spi: pxa2xx: Print actual DMA/PIO transfer mode in debug messages

Transfer debug messages don't actually show is the transfer really using
DMA. Driver may fall back to PIO in case transfer size is not within the
certain limits or fails to map DMA buffers but debug messages don't reveal
that.

Move these debug messages further in pump_transfers() where the actual
transfer mode is known and use drv_data->dma_mapped flag instead of
chip->enable_dma for printing the mode.

Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

diff --git a/drivers/spi/spi-pxa2xx.c b/drivers/spi/spi-pxa2xx.c
index ab9914a..227e8ba 100644 (file)
--- a/drivers/spi/spi-pxa2xx.c
+++ b/drivers/spi/spi-pxa2xx.c
@@ -1001,19 +1001,6 @@ static void pump_transfers(unsigned long data)
                                             "pump_transfers: DMA burst size reduced to match bits_per_word\n");
        }
 
-       /* NOTE:  PXA25x_SSP _could_ use external clocking ... */
-       cr0 = pxa2xx_configure_sscr0(drv_data, clk_div, bits);
-       if (!pxa25x_ssp_comp(drv_data))
-               dev_dbg(&message->spi->dev, "%u Hz actual, %s\n",
-                       drv_data->master->max_speed_hz
-                               / (1 + ((cr0 & SSCR0_SCR(0xfff)) >> 8)),
-                       chip->enable_dma ? "DMA" : "PIO");
-       else
-               dev_dbg(&message->spi->dev, "%u Hz actual, %s\n",
-                       drv_data->master->max_speed_hz / 2
-                               / (1 + ((cr0 & SSCR0_SCR(0x0ff)) >> 8)),
-                       chip->enable_dma ? "DMA" : "PIO");
-
        message->state = RUNNING_STATE;
 
        drv_data->dma_mapped = 0;
@@ -1040,6 +1027,19 @@ static void pump_transfers(unsigned long data)
                write_SSSR_CS(drv_data, drv_data->clear_sr);
        }
 
+       /* NOTE:  PXA25x_SSP _could_ use external clocking ... */
+       cr0 = pxa2xx_configure_sscr0(drv_data, clk_div, bits);
+       if (!pxa25x_ssp_comp(drv_data))
+               dev_dbg(&message->spi->dev, "%u Hz actual, %s\n",
+                       drv_data->master->max_speed_hz
+                               / (1 + ((cr0 & SSCR0_SCR(0xfff)) >> 8)),
+                       drv_data->dma_mapped ? "DMA" : "PIO");
+       else
+               dev_dbg(&message->spi->dev, "%u Hz actual, %s\n",
+                       drv_data->master->max_speed_hz / 2
+                               / (1 + ((cr0 & SSCR0_SCR(0x0ff)) >> 8)),
+                       drv_data->dma_mapped ? "DMA" : "PIO");
+
        if (is_lpss_ssp(drv_data)) {
                if ((pxa2xx_spi_read(drv_data, SSIRF) & 0xff)
                    != chip->lpss_rx_threshold)