commit
781f0766cc41a9dd2e5d118ef4b1d5d89430257b upstream.
Devices connected under Terminus Technology Inc. Hub (1a40:0101) may
fail to work after the system resumes from suspend:
[ 206.063325] usb 3-2.4: reset full-speed USB device number 4 using xhci_hcd
[ 206.143691] usb 3-2.4: device descriptor read/64, error -32
[ 206.351671] usb 3-2.4: device descriptor read/64, error -32
Info for this hub:
T: Bus=03 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 2 Spd=480 MxCh= 4
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=1a40 ProdID=0101 Rev=01.11
S: Product=USB 2.0 Hub
C: #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=100mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
Some expirements indicate that the USB devices connected to the hub are
innocent, it's the hub itself is to blame. The hub needs extra delay
time after it resets its port.
Hence wait for extra delay, if the device is connected to this quirky
hub.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
prevent spurious wakeup);
n = USB_QUIRK_DELAY_CTRL_MSG (Device needs a
pause after every control message);
+ o = USB_QUIRK_HUB_SLOW_RESET (Hub needs extra
+ delay after resetting its port);
Example: quirks=0781:5580:bk,0a5c:5834:gij
usbhid.mousepoll=
int i, status;
u16 portchange, portstatus;
struct usb_port *port_dev = hub->ports[port1 - 1];
+ int reset_recovery_time;
if (!hub_is_superspeed(hub->hdev)) {
if (warm) {
done:
if (status == 0) {
- /* TRSTRCY = 10 ms; plus some extra */
if (port_dev->quirks & USB_PORT_QUIRK_FAST_ENUM)
usleep_range(10000, 12000);
- else
- msleep(10 + 40);
+ else {
+ /* TRSTRCY = 10 ms; plus some extra */
+ reset_recovery_time = 10 + 40;
+
+ /* Hub needs extra delay after resetting its port. */
+ if (hub->hdev->quirks & USB_QUIRK_HUB_SLOW_RESET)
+ reset_recovery_time += 100;
+
+ msleep(reset_recovery_time);
+ }
if (udev) {
struct usb_hcd *hcd = bus_to_hcd(udev->bus);
case 'n':
flags |= USB_QUIRK_DELAY_CTRL_MSG;
break;
+ case 'o':
+ flags |= USB_QUIRK_HUB_SLOW_RESET;
+ break;
/* Ignore unrecognized flag characters */
}
}
{ USB_DEVICE(0x1a0a, 0x0200), .driver_info =
USB_QUIRK_LINEAR_UFRAME_INTR_BINTERVAL },
+ /* Terminus Technology Inc. Hub */
+ { USB_DEVICE(0x1a40, 0x0101), .driver_info = USB_QUIRK_HUB_SLOW_RESET },
+
/* Corsair K70 RGB */
{ USB_DEVICE(0x1b1c, 0x1b13), .driver_info = USB_QUIRK_DELAY_INIT },
/* Device needs a pause after every control message. */
#define USB_QUIRK_DELAY_CTRL_MSG BIT(13)
+/* Hub needs extra delay after resetting its port. */
+#define USB_QUIRK_HUB_SLOW_RESET BIT(14)
+
#endif /* __LINUX_USB_QUIRKS_H */