Required root node properties:
compatible = "raspberrypi,2-model-b", "brcm,bcm2836";
+Raspberry Pi 3 Model B
+Required root node properties:
+compatible = "raspberrypi,3-model-b", "brcm,bcm2837";
+
Raspberry Pi Compute Module
Required root node properties:
compatible = "raspberrypi,compute-module", "brcm,bcm2835";
"mediatek,mt6580"
"mediatek,mt6589"
"mediatek,mt6592"
+ "mediatek,mt6755"
"mediatek,mt6795"
"mediatek,mt7623"
"mediatek,mt8127"
- Evaluation board for MT6592:
Required root node properties:
- compatible = "mediatek,mt6592-evb", "mediatek,mt6592";
+- Evaluation phone for MT6755(Helio P10):
+ Required root node properties:
+ - compatible = "mediatek,mt6755-evb", "mediatek,mt6755";
- Evaluation board for MT6795(Helio X10):
Required root node properties:
- compatible = "mediatek,mt6795-evb", "mediatek,mt6795";
compatible = "renesas,r8a7794"
- R-Car H3 (R8A77950)
compatible = "renesas,r8a7795"
+ - R-Car M3-W (R8A77960)
+ compatible = "renesas,r8a7796"
Boards:
compatible = "renesas,porter", "renesas,r8a7791"
- Salvator-X (RTP0RC7795SIPB0010S)
compatible = "renesas,salvator-x", "renesas,r8a7795";
+ - Salvator-X
+ compatible = "renesas,salvator-x", "renesas,r8a7796";
- SILK (RTP0RC7794LCB00011S)
compatible = "renesas,silk", "renesas,r8a7794"
Required properties:
- compatible : compatible string, one of:
- "allwinner,sun4i-a10-ahci"
+ - "brcm,iproc-ahci"
- "hisilicon,hisi-ahci"
- "cavium,octeon-7130-ahci"
- "ibm,476gtr-ahci"
"mediatek,mt8135-sysirq"
"mediatek,mt8127-sysirq"
"mediatek,mt6795-sysirq"
+ "mediatek,mt6755-sysirq"
"mediatek,mt6592-sysirq"
"mediatek,mt6589-sysirq"
"mediatek,mt6582-sysirq"
compatible = "apm,xgene-enet";
status = "disabled";
reg = <0x0 0x17020000 0x0 0xd100>,
- <0x0 0X17030000 0x0 0X400>,
- <0x0 0X10000000 0x0 0X200>;
+ <0x0 0x17030000 0x0 0x400>,
+ <0x0 0x10000000 0x0 0x200>;
reg-names = "enet_csr", "ring_csr", "ring_cmd";
interrupts = <0x0 0x3c 0x4>;
port-id = <0>;
The first entry must be a link to the SCFG device node
The second entry must be '0' or '1' based on physical PCIe controller index.
This is used to get SCFG PEXN registers
+- dma-coherent: Indicates that the hardware IP block can ensure the coherency
+ of the data transferred from/to the IP block. This can avoid the software
+ cache flush/invalid actions, and improve the performance significantly.
Example:
#address-cells = <3>;
#size-cells = <2>;
device_type = "pci";
+ dma-coherent;
num-lanes = <4>;
bus-range = <0x0 0xff>;
ranges = <0x81000000 0x0 0x00000000 0x40 0x00010000 0x0 0x00010000 /* downstream I/O */
"amlogic,meson8b-cbus-pinctrl"
"amlogic,meson8-aobus-pinctrl"
"amlogic,meson8b-aobus-pinctrl"
+ "amlogic,meson-gxbb-periphs-pinctrl"
+ "amlogic,meson-gxbb-aobus-pinctrl"
- reg: address and size of registers controlling irq functionality
=== GPIO sub-nodes ===
--- /dev/null
+Amlogic Meson Random number generator
+=====================================
+
+Required properties:
+
+- compatible : should be "amlogic,meson-rng"
+- reg : Specifies base physical address and size of the registers.
+
+Example:
+
+rng {
+ compatible = "amlogic,meson-rng";
+ reg = <0x0 0xc8834000 0x0 0x4>;
+};
* "mediatek,mt6580-uart" for MT6580 compatible UARTS
* "mediatek,mt6582-uart" for MT6582 compatible UARTS
* "mediatek,mt6589-uart" for MT6589 compatible UARTS
+ * "mediatek,mt6755-uart" for MT6755 compatible UARTS
* "mediatek,mt6795-uart" for MT6795 compatible UARTS
* "mediatek,mt7623-uart" for MT7623 compatible UARTS
* "mediatek,mt8127-uart" for MT8127 compatible UARTS
help
This enables support for the Renesas R-Car H3 SoC.
+config ARCH_R8A7796
+ bool "Renesas R-Car M3-W SoC Platform"
+ depends on ARCH_RENESAS
+ help
+ This enables support for the Renesas R-Car M3-W SoC.
+
config ARCH_STRATIX10
bool "Altera's Stratix 10 SoCFPGA Family"
help
/dts-v1/;
#include "meson-gxbb.dtsi"
+#include <dt-bindings/gpio/gpio.h>
/ {
compatible = "hardkernel,odroid-c2", "amlogic,meson-gxbb";
device_type = "memory";
reg = <0x0 0x0 0x0 0x80000000>;
};
+
+ leds {
+ compatible = "gpio-leds";
+ blue {
+ label = "c2:blue:alive";
+ gpios = <&gpio_ao GPIOAO_13 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "heartbeat";
+ default-state = "off";
+ };
+ };
};
&uart_AO {
status = "okay";
+ pinctrl-0 = <&uart_ao_a_pins>;
+ pinctrl-names = "default";
+};
+
+ðmac {
+ status = "okay";
+ pinctrl-0 = <ð_pins>;
+ pinctrl-names = "default";
};
+
/* This UART is brought out to the DB9 connector */
&uart_AO {
status = "okay";
+ pinctrl-0 = <&uart_ao_a_pins>;
+ pinctrl-names = "default";
};
+
+ðmac {
+ status = "okay";
+ pinctrl-0 = <ð_pins>;
+ pinctrl-names = "default";
+};
+
&uart_AO {
status = "okay";
+ pinctrl-0 = <&uart_ao_a_pins>;
+ pinctrl-names = "default";
+
};
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/gpio/meson-gxbb-gpio.h>
+#include <dt-bindings/reset/amlogic,meson-gxbb-reset.h>
/ {
compatible = "amlogic,meson-gxbb";
#size-cells = <2>;
ranges = <0x0 0x0 0x0 0xc1100000 0x0 0x100000>;
+ reset: reset-controller@4404 {
+ compatible = "amlogic,meson-gxbb-reset";
+ reg = <0x0 0x04404 0x0 0x20>;
+ #reset-cells = <1>;
+ };
+
uart_A: serial@84c0 {
compatible = "amlogic,meson-uart";
- reg = <0x0 0x084c0 0x0 0x14>;
+ reg = <0x0 0x84c0 0x0 0x14>;
interrupts = <GIC_SPI 26 IRQ_TYPE_EDGE_RISING>;
clocks = <&xtal>;
status = "disabled";
};
+
+ uart_B: serial@84dc {
+ compatible = "amlogic,meson-uart";
+ reg = <0x0 0x84dc 0x0 0x14>;
+ interrupts = <GIC_SPI 75 IRQ_TYPE_EDGE_RISING>;
+ clocks = <&xtal>;
+ status = "disabled";
+ };
+
+ uart_C: serial@8700 {
+ compatible = "amlogic,meson-uart";
+ reg = <0x0 0x8700 0x0 0x14>;
+ interrupts = <GIC_SPI 93 IRQ_TYPE_EDGE_RISING>;
+ clocks = <&xtal>;
+ status = "disabled";
+ };
};
gic: interrupt-controller@c4301000 {
#size-cells = <2>;
ranges = <0x0 0x0 0x0 0xc8100000 0x0 0x100000>;
+ pinctrl_aobus: pinctrl@14 {
+ compatible = "amlogic,meson-gxbb-aobus-pinctrl";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ gpio_ao: bank@14 {
+ reg = <0x0 0x00014 0x0 0x8>,
+ <0x0 0x0002c 0x0 0x4>,
+ <0x0 0x00024 0x0 0x8>;
+ reg-names = "mux", "pull", "gpio";
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+
+ uart_ao_a_pins: uart_ao_a {
+ mux {
+ groups = "uart_tx_ao_a", "uart_rx_ao_a";
+ function = "uart_ao";
+ };
+ };
+ };
+
uart_AO: serial@4c0 {
compatible = "amlogic,meson-uart";
reg = <0x0 0x004c0 0x0 0x14>;
};
};
+ periphs: periphs@c8834000 {
+ compatible = "simple-bus";
+ reg = <0x0 0xc8834000 0x0 0x2000>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges = <0x0 0x0 0x0 0xc8834000 0x0 0x2000>;
+
+ rng {
+ compatible = "amlogic,meson-rng";
+ reg = <0x0 0x0 0x0 0x4>;
+ };
+
+ pinctrl_periphs: pinctrl@4b0 {
+ compatible = "amlogic,meson-gxbb-periphs-pinctrl";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ gpio: bank@4b0 {
+ reg = <0x0 0x004b0 0x0 0x28>,
+ <0x0 0x004e8 0x0 0x14>,
+ <0x0 0x00120 0x0 0x14>,
+ <0x0 0x00430 0x0 0x40>;
+ reg-names = "mux", "pull", "pull-enable", "gpio";
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+
+ emmc_pins: emmc {
+ mux {
+ groups = "emmc_nand_d07",
+ "emmc_cmd",
+ "emmc_clk";
+ function = "emmc";
+ };
+ };
+
+ sdcard_pins: sdcard {
+ mux {
+ groups = "sdcard_d0",
+ "sdcard_d1",
+ "sdcard_d2",
+ "sdcard_d3",
+ "sdcard_cmd",
+ "sdcard_clk";
+ function = "sdcard";
+ };
+ };
+
+ uart_a_pins: uart_a {
+ mux {
+ groups = "uart_tx_a",
+ "uart_rx_a";
+ function = "uart_a";
+ };
+ };
+
+ uart_b_pins: uart_b {
+ mux {
+ groups = "uart_tx_b",
+ "uart_rx_b";
+ function = "uart_b";
+ };
+ };
+
+ uart_c_pins: uart_c {
+ mux {
+ groups = "uart_tx_c",
+ "uart_rx_c";
+ function = "uart_c";
+ };
+ };
+
+ eth_pins: eth_c {
+ mux {
+ groups = "eth_mdio",
+ "eth_mdc",
+ "eth_clk_rx_clk",
+ "eth_rx_dv",
+ "eth_rxd0",
+ "eth_rxd1",
+ "eth_rxd2",
+ "eth_rxd3",
+ "eth_rgmii_tx_clk",
+ "eth_tx_en",
+ "eth_txd0",
+ "eth_txd1",
+ "eth_txd2",
+ "eth_txd3";
+ function = "eth";
+ };
+ };
+ };
+ };
+
+ hiubus: hiubus@c883c000 {
+ compatible = "simple-bus";
+ reg = <0x0 0xc883c000 0x0 0x2000>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges = <0x0 0x0 0x0 0xc883c000 0x0 0x2000>;
+
+ clkc: clock-controller@0 {
+ compatible = "amlogic,gxbb-clkc";
+ #clock-cells = <1>;
+ reg = <0x0 0x0 0x0 0x3db>;
+ };
+ };
+
apb: apb@d0000000 {
compatible = "simple-bus";
reg = <0x0 0xd0000000 0x0 0x200000>;
#size-cells = <2>;
ranges = <0x0 0x0 0x0 0xd0000000 0x0 0x200000>;
};
+
+ ethmac: ethernet@c9410000 {
+ compatible = "amlogic,meson6-dwmac", "snps,dwmac";
+ reg = <0x0 0xc9410000 0x0 0x10000
+ 0x0 0xc8834540 0x0 0x4>;
+ interrupts = <0 8 1>;
+ interrupt-names = "macirq";
+ clocks = <&xtal>;
+ clock-names = "stmmaceth";
+ phy-mode = "rgmii";
+ status = "disabled";
+ };
};
};
interrupts = <1 9 0xf04>; /* GIC Maintenence IRQ */
ranges = <0 0 0 0x79000000 0x0 0x800000>; /* MSI Range */
reg = <0x0 0x78090000 0x0 0x10000>, /* GIC Dist */
- <0x0 0x780A0000 0x0 0x20000>, /* GIC CPU */
- <0x0 0x780C0000 0x0 0x10000>, /* GIC VCPU Control */
- <0x0 0x780E0000 0x0 0x20000>; /* GIC VCPU */
- v2m0: v2m@0x00000 {
+ <0x0 0x780a0000 0x0 0x20000>, /* GIC CPU */
+ <0x0 0x780c0000 0x0 0x10000>, /* GIC VCPU Control */
+ <0x0 0x780e0000 0x0 0x20000>; /* GIC VCPU */
+ v2m0: v2m@00000 {
compatible = "arm,gic-v2m-frame";
msi-controller;
reg = <0x0 0x0 0x0 0x1000>;
};
- v2m1: v2m@0x10000 {
+ v2m1: v2m@10000 {
compatible = "arm,gic-v2m-frame";
msi-controller;
reg = <0x0 0x10000 0x0 0x1000>;
};
- v2m2: v2m@0x20000 {
+ v2m2: v2m@20000 {
compatible = "arm,gic-v2m-frame";
msi-controller;
reg = <0x0 0x20000 0x0 0x1000>;
};
- v2m3: v2m@0x30000 {
+ v2m3: v2m@30000 {
compatible = "arm,gic-v2m-frame";
msi-controller;
reg = <0x0 0x30000 0x0 0x1000>;
};
- v2m4: v2m@0x40000 {
+ v2m4: v2m@40000 {
compatible = "arm,gic-v2m-frame";
msi-controller;
reg = <0x0 0x40000 0x0 0x1000>;
};
- v2m5: v2m@0x50000 {
+ v2m5: v2m@50000 {
compatible = "arm,gic-v2m-frame";
msi-controller;
reg = <0x0 0x50000 0x0 0x1000>;
};
- v2m6: v2m@0x60000 {
+ v2m6: v2m@60000 {
compatible = "arm,gic-v2m-frame";
msi-controller;
reg = <0x0 0x60000 0x0 0x1000>;
};
- v2m7: v2m@0x70000 {
+ v2m7: v2m@70000 {
compatible = "arm,gic-v2m-frame";
msi-controller;
reg = <0x0 0x70000 0x0 0x1000>;
};
- v2m8: v2m@0x80000 {
+ v2m8: v2m@80000 {
compatible = "arm,gic-v2m-frame";
msi-controller;
reg = <0x0 0x80000 0x0 0x1000>;
};
- v2m9: v2m@0x90000 {
+ v2m9: v2m@90000 {
compatible = "arm,gic-v2m-frame";
msi-controller;
reg = <0x0 0x90000 0x0 0x1000>;
};
- v2m10: v2m@0xA0000 {
+ v2m10: v2m@a0000 {
compatible = "arm,gic-v2m-frame";
msi-controller;
- reg = <0x0 0xA0000 0x0 0x1000>;
+ reg = <0x0 0xa0000 0x0 0x1000>;
};
- v2m11: v2m@0xB0000 {
+ v2m11: v2m@b0000 {
compatible = "arm,gic-v2m-frame";
msi-controller;
- reg = <0x0 0xB0000 0x0 0x1000>;
+ reg = <0x0 0xb0000 0x0 0x1000>;
};
- v2m12: v2m@0xC0000 {
+ v2m12: v2m@c0000 {
compatible = "arm,gic-v2m-frame";
msi-controller;
- reg = <0x0 0xC0000 0x0 0x1000>;
+ reg = <0x0 0xc0000 0x0 0x1000>;
};
- v2m13: v2m@0xD0000 {
+ v2m13: v2m@d0000 {
compatible = "arm,gic-v2m-frame";
msi-controller;
- reg = <0x0 0xD0000 0x0 0x1000>;
+ reg = <0x0 0xd0000 0x0 0x1000>;
};
- v2m14: v2m@0xE0000 {
+ v2m14: v2m@e0000 {
compatible = "arm,gic-v2m-frame";
msi-controller;
- reg = <0x0 0xE0000 0x0 0x1000>;
+ reg = <0x0 0xe0000 0x0 0x1000>;
};
- v2m15: v2m@0xF0000 {
+ v2m15: v2m@f0000 {
compatible = "arm,gic-v2m-frame";
msi-controller;
- reg = <0x0 0xF0000 0x0 0x1000>;
+ reg = <0x0 0xf0000 0x0 0x1000>;
};
};
timer {
compatible = "arm,armv8-timer";
- interrupts = <1 0 0xff04>, /* Secure Phys IRQ */
- <1 13 0xff04>, /* Non-secure Phys IRQ */
- <1 14 0xff04>, /* Virt IRQ */
- <1 15 0xff04>; /* Hyp IRQ */
+ interrupts = <1 0 0xff08>, /* Secure Phys IRQ */
+ <1 13 0xff08>, /* Non-secure Phys IRQ */
+ <1 14 0xff08>, /* Virt IRQ */
+ <1 15 0xff08>; /* Hyp IRQ */
clock-frequency = <50000000>;
};
compatible = "apm,xgene2-sgenet";
status = "disabled";
reg = <0x0 0x1f610000 0x0 0xd100>,
- <0x0 0x1f600000 0x0 0Xd100>,
- <0x0 0x20000000 0x0 0X20000>;
+ <0x0 0x1f600000 0x0 0xd100>,
+ <0x0 0x20000000 0x0 0x20000>;
interrupts = <0 96 4>,
<0 97 4>;
dma-coherent;
compatible = "apm,xgene2-xgenet";
status = "disabled";
reg = <0x0 0x1f620000 0x0 0x10000>,
- <0x0 0x1f600000 0x0 0Xd100>,
- <0x0 0x20000000 0x0 0X220000>;
+ <0x0 0x1f600000 0x0 0xd100>,
+ <0x0 0x20000000 0x0 0x220000>;
interrupts = <0 108 4>,
<0 109 4>,
<0 110 4>,
#size-cells = <0>;
compatible = "snps,designware-i2c";
reg = <0x0 0x10640000 0x0 0x1000>;
- interrupts = <0 0x3A 0x4>;
+ interrupts = <0 0x3a 0x4>;
clocks = <&i2c4clk 0>;
bus_num = <4>;
};
clock-output-names = "sdioclk";
};
- qmlclk: qmlclk {
- compatible = "apm,xgene-device-clock";
- #clock-cells = <1>;
- clocks = <&socplldiv2 0>;
- clock-names = "qmlclk";
- reg = <0x0 0x1703C000 0x0 0x1000>;
- reg-names = "csr-reg";
- clock-output-names = "qmlclk";
- };
-
ethclk: ethclk {
compatible = "apm,xgene-device-clock";
#clock-cells = <1>;
compatible = "apm,xgene-device-clock";
#clock-cells = <1>;
clocks = <ðclk 0>;
- reg = <0x0 0x1702C000 0x0 0x1000>;
+ reg = <0x0 0x1702c000 0x0 0x1000>;
reg-names = "csr-reg";
clock-output-names = "menetclk";
};
compatible = "apm,xgene-enet";
status = "disabled";
reg = <0x0 0x17020000 0x0 0xd100>,
- <0x0 0X17030000 0x0 0Xc300>,
- <0x0 0X10000000 0x0 0X200>;
+ <0x0 0x17030000 0x0 0xc300>,
+ <0x0 0x10000000 0x0 0x200>;
reg-names = "enet_csr", "ring_csr", "ring_cmd";
interrupts = <0x0 0x3c 0x4>;
dma-coherent;
compatible = "apm,xgene1-sgenet";
status = "disabled";
reg = <0x0 0x1f210000 0x0 0xd100>,
- <0x0 0x1f200000 0x0 0Xc300>,
- <0x0 0x1B000000 0x0 0X200>;
+ <0x0 0x1f200000 0x0 0xc300>,
+ <0x0 0x1b000000 0x0 0x200>;
reg-names = "enet_csr", "ring_csr", "ring_cmd";
- interrupts = <0x0 0xA0 0x4>,
- <0x0 0xA1 0x4>;
+ interrupts = <0x0 0xa0 0x4>,
+ <0x0 0xa1 0x4>;
dma-coherent;
clocks = <&sge0clk 0>;
local-mac-address = [00 00 00 00 00 00];
compatible = "apm,xgene1-sgenet";
status = "disabled";
reg = <0x0 0x1f210030 0x0 0xd100>,
- <0x0 0x1f200000 0x0 0Xc300>,
- <0x0 0x1B000000 0x0 0X8000>;
+ <0x0 0x1f200000 0x0 0xc300>,
+ <0x0 0x1b000000 0x0 0x8000>;
reg-names = "enet_csr", "ring_csr", "ring_cmd";
- interrupts = <0x0 0xAC 0x4>,
- <0x0 0xAD 0x4>;
+ interrupts = <0x0 0xac 0x4>,
+ <0x0 0xad 0x4>;
port-id = <1>;
dma-coherent;
local-mac-address = [00 00 00 00 00 00];
compatible = "apm,xgene1-xgenet";
status = "disabled";
reg = <0x0 0x1f610000 0x0 0xd100>,
- <0x0 0x1f600000 0x0 0Xc300>,
- <0x0 0x18000000 0x0 0X200>;
+ <0x0 0x1f600000 0x0 0xc300>,
+ <0x0 0x18000000 0x0 0x200>;
reg-names = "enet_csr", "ring_csr", "ring_cmd";
interrupts = <0x0 0x60 0x4>,
<0x0 0x61 0x4>,
compatible = "apm,xgene1-xgenet";
status = "disabled";
reg = <0x0 0x1f620000 0x0 0xd100>,
- <0x0 0x1f600000 0x0 0Xc300>,
- <0x0 0x18000000 0x0 0X8000>;
+ <0x0 0x1f600000 0x0 0xc300>,
+ <0x0 0x18000000 0x0 0x8000>;
reg-names = "enet_csr", "ring_csr", "ring_cmd";
- interrupts = <0x0 0x6C 0x4>,
- <0x0 0x6D 0x4>;
+ interrupts = <0x0 0x6c 0x4>,
+ <0x0 0x6d 0x4>;
port-id = <1>;
dma-coherent;
clocks = <&xge1clk 0>;
<GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(6) | IRQ_TYPE_LEVEL_LOW)>;
};
+ /*
+ * Juno TRMs specify the size for these coresight components as 64K.
+ * The actual size is just 4K though 64K is reserved. Access to the
+ * unmapped reserved region results in a DECERR response.
+ */
+ etf@20010000 {
+ compatible = "arm,coresight-tmc", "arm,primecell";
+ reg = <0 0x20010000 0 0x1000>;
+
+ clocks = <&soc_smc50mhz>;
+ clock-names = "apb_pclk";
+ power-domains = <&scpi_devpd 0>;
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /* input port */
+ port@0 {
+ reg = <0>;
+ etf_in_port: endpoint {
+ slave-mode;
+ remote-endpoint = <&main_funnel_out_port>;
+ };
+ };
+
+ /* output port */
+ port@1 {
+ reg = <0>;
+ etf_out_port: endpoint {
+ remote-endpoint = <&replicator_in_port0>;
+ };
+ };
+ };
+ };
+
+ tpiu@20030000 {
+ compatible = "arm,coresight-tpiu", "arm,primecell";
+ reg = <0 0x20030000 0 0x1000>;
+
+ clocks = <&soc_smc50mhz>;
+ clock-names = "apb_pclk";
+ power-domains = <&scpi_devpd 0>;
+ port {
+ tpiu_in_port: endpoint {
+ slave-mode;
+ remote-endpoint = <&replicator_out_port0>;
+ };
+ };
+ };
+
+ main-funnel@20040000 {
+ compatible = "arm,coresight-funnel", "arm,primecell";
+ reg = <0 0x20040000 0 0x1000>;
+
+ clocks = <&soc_smc50mhz>;
+ clock-names = "apb_pclk";
+ power-domains = <&scpi_devpd 0>;
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ main_funnel_out_port: endpoint {
+ remote-endpoint = <&etf_in_port>;
+ };
+ };
+
+ port@1 {
+ reg = <0>;
+ main_funnel_in_port0: endpoint {
+ slave-mode;
+ remote-endpoint = <&cluster0_funnel_out_port>;
+ };
+ };
+
+ port@2 {
+ reg = <1>;
+ main_funnel_in_port1: endpoint {
+ slave-mode;
+ remote-endpoint = <&cluster1_funnel_out_port>;
+ };
+ };
+
+ };
+ };
+
+ etr@20070000 {
+ compatible = "arm,coresight-tmc", "arm,primecell";
+ reg = <0 0x20070000 0 0x1000>;
+
+ clocks = <&soc_smc50mhz>;
+ clock-names = "apb_pclk";
+ power-domains = <&scpi_devpd 0>;
+ port {
+ etr_in_port: endpoint {
+ slave-mode;
+ remote-endpoint = <&replicator_out_port1>;
+ };
+ };
+ };
+
+ etm0: etm@22040000 {
+ compatible = "arm,coresight-etm4x", "arm,primecell";
+ reg = <0 0x22040000 0 0x1000>;
+
+ clocks = <&soc_smc50mhz>;
+ clock-names = "apb_pclk";
+ power-domains = <&scpi_devpd 0>;
+ port {
+ cluster0_etm0_out_port: endpoint {
+ remote-endpoint = <&cluster0_funnel_in_port0>;
+ };
+ };
+ };
+
+ cluster0-funnel@220c0000 {
+ compatible = "arm,coresight-funnel", "arm,primecell";
+ reg = <0 0x220c0000 0 0x1000>;
+
+ clocks = <&soc_smc50mhz>;
+ clock-names = "apb_pclk";
+ power-domains = <&scpi_devpd 0>;
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ cluster0_funnel_out_port: endpoint {
+ remote-endpoint = <&main_funnel_in_port0>;
+ };
+ };
+
+ port@1 {
+ reg = <0>;
+ cluster0_funnel_in_port0: endpoint {
+ slave-mode;
+ remote-endpoint = <&cluster0_etm0_out_port>;
+ };
+ };
+
+ port@2 {
+ reg = <1>;
+ cluster0_funnel_in_port1: endpoint {
+ slave-mode;
+ remote-endpoint = <&cluster0_etm1_out_port>;
+ };
+ };
+ };
+ };
+
+ etm1: etm@22140000 {
+ compatible = "arm,coresight-etm4x", "arm,primecell";
+ reg = <0 0x22140000 0 0x1000>;
+
+ clocks = <&soc_smc50mhz>;
+ clock-names = "apb_pclk";
+ power-domains = <&scpi_devpd 0>;
+ port {
+ cluster0_etm1_out_port: endpoint {
+ remote-endpoint = <&cluster0_funnel_in_port1>;
+ };
+ };
+ };
+
+ etm2: etm@23040000 {
+ compatible = "arm,coresight-etm4x", "arm,primecell";
+ reg = <0 0x23040000 0 0x1000>;
+
+ clocks = <&soc_smc50mhz>;
+ clock-names = "apb_pclk";
+ power-domains = <&scpi_devpd 0>;
+ port {
+ cluster1_etm0_out_port: endpoint {
+ remote-endpoint = <&cluster1_funnel_in_port0>;
+ };
+ };
+ };
+
+ cluster1-funnel@230c0000 {
+ compatible = "arm,coresight-funnel", "arm,primecell";
+ reg = <0 0x230c0000 0 0x1000>;
+
+ clocks = <&soc_smc50mhz>;
+ clock-names = "apb_pclk";
+ power-domains = <&scpi_devpd 0>;
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ cluster1_funnel_out_port: endpoint {
+ remote-endpoint = <&main_funnel_in_port1>;
+ };
+ };
+
+ port@1 {
+ reg = <0>;
+ cluster1_funnel_in_port0: endpoint {
+ slave-mode;
+ remote-endpoint = <&cluster1_etm0_out_port>;
+ };
+ };
+
+ port@2 {
+ reg = <1>;
+ cluster1_funnel_in_port1: endpoint {
+ slave-mode;
+ remote-endpoint = <&cluster1_etm1_out_port>;
+ };
+ };
+ port@3 {
+ reg = <2>;
+ cluster1_funnel_in_port2: endpoint {
+ slave-mode;
+ remote-endpoint = <&cluster1_etm2_out_port>;
+ };
+ };
+ port@4 {
+ reg = <3>;
+ cluster1_funnel_in_port3: endpoint {
+ slave-mode;
+ remote-endpoint = <&cluster1_etm3_out_port>;
+ };
+ };
+ };
+ };
+
+ etm3: etm@23140000 {
+ compatible = "arm,coresight-etm4x", "arm,primecell";
+ reg = <0 0x23140000 0 0x1000>;
+
+ clocks = <&soc_smc50mhz>;
+ clock-names = "apb_pclk";
+ power-domains = <&scpi_devpd 0>;
+ port {
+ cluster1_etm1_out_port: endpoint {
+ remote-endpoint = <&cluster1_funnel_in_port1>;
+ };
+ };
+ };
+
+ etm4: etm@23240000 {
+ compatible = "arm,coresight-etm4x", "arm,primecell";
+ reg = <0 0x23240000 0 0x1000>;
+
+ clocks = <&soc_smc50mhz>;
+ clock-names = "apb_pclk";
+ power-domains = <&scpi_devpd 0>;
+ port {
+ cluster1_etm2_out_port: endpoint {
+ remote-endpoint = <&cluster1_funnel_in_port2>;
+ };
+ };
+ };
+
+ etm5: etm@23340000 {
+ compatible = "arm,coresight-etm4x", "arm,primecell";
+ reg = <0 0x23340000 0 0x1000>;
+
+ clocks = <&soc_smc50mhz>;
+ clock-names = "apb_pclk";
+ power-domains = <&scpi_devpd 0>;
+ port {
+ cluster1_etm3_out_port: endpoint {
+ remote-endpoint = <&cluster1_funnel_in_port3>;
+ };
+ };
+ };
+
+ coresight-replicator {
+ /*
+ * Non-configurable replicators don't show up on the
+ * AMBA bus. As such no need to add "arm,primecell".
+ */
+ compatible = "arm,coresight-replicator";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /* replicator output ports */
+ port@0 {
+ reg = <0>;
+ replicator_out_port0: endpoint {
+ remote-endpoint = <&tpiu_in_port>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ replicator_out_port1: endpoint {
+ remote-endpoint = <&etr_in_port>;
+ };
+ };
+
+ /* replicator input port */
+ port@2 {
+ reg = <0>;
+ replicator_in_port0: endpoint {
+ slave-mode;
+ remote-endpoint = <&etf_out_port>;
+ };
+ };
+ };
+ };
+
sram: sram@2e000000 {
compatible = "arm,juno-sram-ns", "mmio-sram";
reg = <0x0 0x2e000000 0x0 0x8000>;
};
};
+ scpi_devpd: scpi-power-domains {
+ compatible = "arm,scpi-power-domains";
+ num-domains = <2>;
+ #power-domain-cells = <1>;
+ };
+
scpi_sensors0: sensors {
compatible = "arm,scpi-sensors";
#thermal-sensor-cells = <1>;
};
};
+ thermal-zones {
+ pmic {
+ polling-delay = <1000>;
+ polling-delay-passive = <100>;
+ thermal-sensors = <&scpi_sensors0 0>;
+ };
+
+ soc {
+ polling-delay = <1000>;
+ polling-delay-passive = <100>;
+ thermal-sensors = <&scpi_sensors0 3>;
+ };
+
+ big_cluster_thermal_zone: big_cluster {
+ polling-delay = <1000>;
+ polling-delay-passive = <100>;
+ thermal-sensors = <&scpi_sensors0 21>;
+ status = "disabled";
+ };
+
+ little_cluster_thermal_zone: little_cluster {
+ polling-delay = <1000>;
+ polling-delay-passive = <100>;
+ thermal-sensors = <&scpi_sensors0 22>;
+ status = "disabled";
+ };
+
+ gpu0_thermal_zone: gpu0 {
+ polling-delay = <1000>;
+ polling-delay-passive = <100>;
+ thermal-sensors = <&scpi_sensors0 23>;
+ status = "disabled";
+ };
+
+ gpu1_thermal_zone: gpu1 {
+ polling-delay = <1000>;
+ polling-delay-passive = <100>;
+ thermal-sensors = <&scpi_sensors0 24>;
+ status = "disabled";
+ };
+ };
+
/include/ "juno-clocks.dtsi"
dma@7ff00000 {
&pcie_ctlr {
status = "okay";
};
+
+&etm0 {
+ cpu = <&A57_0>;
+};
+
+&etm1 {
+ cpu = <&A57_1>;
+};
+
+&etm2 {
+ cpu = <&A53_0>;
+};
+
+&etm3 {
+ cpu = <&A53_1>;
+};
+
+&etm4 {
+ cpu = <&A53_2>;
+};
+
+&etm5 {
+ cpu = <&A53_3>;
+};
+
+&big_cluster_thermal_zone {
+ status = "okay";
+};
+
+&little_cluster_thermal_zone {
+ status = "okay";
+};
+
+&gpu0_thermal_zone {
+ status = "okay";
+};
+
+&gpu1_thermal_zone {
+ status = "okay";
+};
&pcie_ctlr {
status = "okay";
};
+
+&etm0 {
+ cpu = <&A72_0>;
+};
+
+&etm1 {
+ cpu = <&A72_1>;
+};
+
+&etm2 {
+ cpu = <&A53_0>;
+};
+
+&etm3 {
+ cpu = <&A53_1>;
+};
+
+&etm4 {
+ cpu = <&A53_2>;
+};
+
+&etm5 {
+ cpu = <&A53_3>;
+};
+
+&big_cluster_thermal_zone {
+ status = "okay";
+};
+
+&little_cluster_thermal_zone {
+ status = "okay";
+};
+
+&gpu0_thermal_zone {
+ status = "okay";
+};
+
+&gpu1_thermal_zone {
+ status = "okay";
+};
#include "juno-base.dtsi"
};
+
+&etm0 {
+ cpu = <&A57_0>;
+};
+
+&etm1 {
+ cpu = <&A57_1>;
+};
+
+&etm2 {
+ cpu = <&A53_0>;
+};
+
+&etm3 {
+ cpu = <&A53_1>;
+};
+
+&etm4 {
+ cpu = <&A53_2>;
+};
+
+&etm5 {
+ cpu = <&A53_3>;
+};
+dtb-$(CONFIG_ARCH_BCM2835) += bcm2837-rpi-3-b.dtb
dtb-$(CONFIG_ARCH_BCM_IPROC) += ns2-svk.dtb
dtb-$(CONFIG_ARCH_VULCAN) += vulcan-eval.dtb
--- /dev/null
+/dts-v1/;
+#include "bcm2837.dtsi"
+#include "../../../../arm/boot/dts/bcm2835-rpi.dtsi"
+#include "../../../../arm/boot/dts/bcm283x-rpi-smsc9514.dtsi"
+
+/ {
+ compatible = "raspberrypi,3-model-b", "brcm,bcm2837";
+ model = "Raspberry Pi 3 Model B";
+
+ memory {
+ reg = <0 0x40000000>;
+ };
+
+ leds {
+ act {
+ gpios = <&gpio 47 0>;
+ };
+
+ pwr {
+ label = "PWR";
+ gpios = <&gpio 35 0>;
+ default-state = "keep";
+ linux,default-trigger = "default-on";
+ };
+ };
+};
+
+&uart1 {
+ status = "okay";
+};
--- /dev/null
+#include "../../../../arm/boot/dts/bcm283x.dtsi"
+
+/ {
+ compatible = "brcm,bcm2836";
+
+ soc {
+ ranges = <0x7e000000 0x3f000000 0x1000000>,
+ <0x40000000 0x40000000 0x00001000>;
+ dma-ranges = <0xc0000000 0x00000000 0x3f000000>;
+
+ local_intc: local_intc {
+ compatible = "brcm,bcm2836-l1-intc";
+ reg = <0x40000000 0x100>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ interrupt-parent = <&local_intc>;
+ };
+ };
+
+ timer {
+ compatible = "arm,armv7-timer";
+ interrupt-parent = <&local_intc>;
+ interrupts = <0>, // PHYS_SECURE_PPI
+ <1>, // PHYS_NONSECURE_PPI
+ <3>, // VIRT_PPI
+ <2>; // HYP_PPI
+ always-on;
+ };
+
+ cpus: cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu0: cpu@0 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ reg = <0>;
+ enable-method = "spin-table";
+ cpu-release-addr = <0x0 0x000000d8>;
+ };
+
+ cpu1: cpu@1 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ reg = <1>;
+ enable-method = "spin-table";
+ cpu-release-addr = <0x0 0x000000e0>;
+ };
+
+ cpu2: cpu@2 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ reg = <2>;
+ enable-method = "spin-table";
+ cpu-release-addr = <0x0 0x000000e8>;
+ };
+
+ cpu3: cpu@3 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ reg = <3>;
+ enable-method = "spin-table";
+ cpu-release-addr = <0x0 0x000000f0>;
+ };
+ };
+};
+
+/* Make the BCM2835-style global interrupt controller be a child of the
+ * CPU-local interrupt controller.
+ */
+&intc {
+ compatible = "brcm,bcm2836-armctrl-ic";
+ reg = <0x7e00b200 0x200>;
+ interrupt-parent = <&local_intc>;
+ interrupts = <8>;
+};
aliases {
serial0 = &uart3;
+ serial1 = &uart0;
+ serial2 = &uart1;
+ serial3 = &uart2;
};
chosen {
stdout-path = "serial0:115200n8";
+ bootargs = "earlycon=uart8250,mmio32,0x66130000";
};
memory {
status = "ok";
};
+&uart0 {
+ status = "ok";
+};
+
+&uart1 {
+ status = "ok";
+};
+
+&uart2 {
+ status = "ok";
+};
+
&uart3 {
status = "ok";
};
};
};
+&sata_phy0 {
+ status = "ok";
+};
+
+&sata_phy1 {
+ status = "ok";
+};
+
+&sata {
+ status = "ok";
+};
+
&sdio0 {
status = "ok";
};
};
};
};
+
+&pinctrl {
+ pinctrl-names = "default";
+ pinctrl-0 = <&nand_sel>;
+ nand_sel: nand_sel {
+ function = "nand";
+ groups = "nand_grp";
+ };
+};
mmu-masters;
};
+ pinctrl: pinctrl@6501d130 {
+ compatible = "brcm,ns2-pinmux";
+ reg = <0x6501d130 0x08>,
+ <0x660a0028 0x04>,
+ <0x660009b0 0x40>;
+ };
+
+ gpio_aon: gpio@65024800 {
+ compatible = "brcm,iproc-gpio";
+ reg = <0x65024800 0x50>,
+ <0x65024008 0x18>;
+ ngpios = <6>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ };
+
gic: interrupt-controller@65210000 {
compatible = "arm,gic-400";
#interrupt-cells = <3>;
IRQ_TYPE_LEVEL_HIGH)>;
};
+ cci@65590000 {
+ compatible = "arm,cci-400";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0x65590000 0x1000>;
+ ranges = <0 0x65590000 0x10000>;
+
+ pmu@9000 {
+ compatible = "arm,cci-400-pmu,r1",
+ "arm,cci-400-pmu";
+ reg = <0x9000 0x4000>;
+ interrupts = <GIC_SPI 344 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 345 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 346 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 347 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 348 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 349 IRQ_TYPE_LEVEL_HIGH>;
+ };
+ };
+
mdio_mux_iproc: mdio-mux@6602023c {
compatible = "brcm,mdio-mux-iproc";
reg = <0x6602023c 0x14>;
clock-names = "wdogclk", "apb_pclk";
};
+ gpio_g: gpio@660a0000 {
+ compatible = "brcm,iproc-gpio";
+ reg = <0x660a0000 0x50>;
+ ngpios = <32>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ interrupt-controller;
+ interrupts = <GIC_SPI 400 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
i2c1: i2c@660b0000 {
compatible = "brcm,iproc-i2c";
reg = <0x660b0000 0x100>;
status = "disabled";
};
+ uart0: serial@66100000 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x66100000 0x100>;
+ interrupts = <GIC_SPI 390 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&iprocslow>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ status = "disabled";
+ };
+
+ uart1: serial@66110000 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x66110000 0x100>;
+ interrupts = <GIC_SPI 391 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&iprocslow>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ status = "disabled";
+ };
+
+ uart2: serial@66120000 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x66120000 0x100>;
+ interrupts = <GIC_SPI 392 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&iprocslow>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ status = "disabled";
+ };
+
uart3: serial@66130000 {
compatible = "snps,dw-apb-uart";
reg = <0x66130000 0x100>;
reg = <0x66220000 0x28>;
};
+ sata_phy: sata_phy@663f0100 {
+ compatible = "brcm,iproc-ns2-sata-phy";
+ reg = <0x663f0100 0x1f00>,
+ <0x663f004c 0x10>;
+ reg-names = "phy", "phy-ctrl";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ sata_phy0: sata-phy@0 {
+ reg = <0>;
+ #phy-cells = <0>;
+ status = "disabled";
+ };
+
+ sata_phy1: sata-phy@1 {
+ reg = <1>;
+ #phy-cells = <0>;
+ status = "disabled";
+ };
+ };
+
+ sata: ahci@663f2000 {
+ compatible = "brcm,iproc-ahci", "generic-ahci";
+ reg = <0x663f2000 0x1000>;
+ reg-names = "ahci";
+ interrupts = <GIC_SPI 438 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+
+ sata0: sata-port@0 {
+ reg = <0>;
+ phys = <&sata_phy0>;
+ phy-names = "sata-phy";
+ };
+
+ sata1: sata-port@1 {
+ reg = <1>;
+ phys = <&sata_phy1>;
+ phy-names = "sata-phy";
+ };
+ };
+
sdio0: sdhci@66420000 {
compatible = "brcm,sdhci-iproc-cygnus";
reg = <0x66420000 0x100>;
buck2_reg: BUCK2 {
regulator-name = "vdd_atlas";
- regulator-min-microvolt = <1200000>;
+ regulator-min-microvolt = <500000>;
regulator-max-microvolt = <1200000>;
regulator-always-on;
regulator-boot-on;
#size-cells = <2>;
cpus {
- #address-cells = <2>;
+ #address-cells = <1>;
#size-cells = <0>;
/*
cpu0: cpu@0 {
device_type = "cpu";
compatible = "arm,cortex-a53";
- reg = <0x0 0x0>;
+ reg = <0x0>;
clocks = <&clockgen 1 0>;
+ next-level-cache = <&l2>;
};
cpu1: cpu@1 {
device_type = "cpu";
compatible = "arm,cortex-a53";
- reg = <0x0 0x1>;
+ reg = <0x1>;
clocks = <&clockgen 1 0>;
+ next-level-cache = <&l2>;
};
cpu2: cpu@2 {
device_type = "cpu";
compatible = "arm,cortex-a53";
- reg = <0x0 0x2>;
+ reg = <0x2>;
clocks = <&clockgen 1 0>;
+ next-level-cache = <&l2>;
};
cpu3: cpu@3 {
device_type = "cpu";
compatible = "arm,cortex-a53";
- reg = <0x0 0x3>;
+ reg = <0x3>;
clocks = <&clockgen 1 0>;
+ next-level-cache = <&l2>;
+ };
+
+ l2: l2-cache {
+ compatible = "cache";
};
};
interrupts = <0 60 0x4>;
dr_mode = "host";
snps,quirk-frame-length-adjustment = <0x20>;
+ snps,dis_rxdet_inp3_quirk;
};
usb1: usb3@3000000 {
interrupts = <0 61 0x4>;
dr_mode = "host";
snps,quirk-frame-length-adjustment = <0x20>;
+ snps,dis_rxdet_inp3_quirk;
};
usb2: usb3@3100000 {
interrupts = <0 63 0x4>;
dr_mode = "host";
snps,quirk-frame-length-adjustment = <0x20>;
+ snps,dis_rxdet_inp3_quirk;
};
sata: sata@3200000 {
#address-cells = <3>;
#size-cells = <2>;
device_type = "pci";
+ dma-coherent;
num-lanes = <4>;
bus-range = <0x0 0xff>;
ranges = <0x81000000 0x0 0x00000000 0x40 0x00010000 0x0 0x00010000 /* downstream I/O */
#address-cells = <3>;
#size-cells = <2>;
device_type = "pci";
+ dma-coherent;
num-lanes = <2>;
bus-range = <0x0 0xff>;
ranges = <0x81000000 0x0 0x00000000 0x48 0x00010000 0x0 0x00010000 /* downstream I/O */
#address-cells = <3>;
#size-cells = <2>;
device_type = "pci";
+ dma-coherent;
num-lanes = <2>;
bus-range = <0x0 0xff>;
ranges = <0x81000000 0x0 0x00000000 0x50 0x00010000 0x0 0x00010000 /* downstream I/O */
#size-cells = <2>;
cpus {
- #address-cells = <2>;
+ #address-cells = <1>;
#size-cells = <0>;
/*
cpu@0 {
device_type = "cpu";
compatible = "arm,cortex-a57";
- reg = <0x0 0x0>;
+ reg = <0x0>;
clocks = <&clockgen 1 0>;
+ next-level-cache = <&cluster0_l2>;
};
cpu@1 {
device_type = "cpu";
compatible = "arm,cortex-a57";
- reg = <0x0 0x1>;
+ reg = <0x1>;
clocks = <&clockgen 1 0>;
+ next-level-cache = <&cluster0_l2>;
};
cpu@100 {
device_type = "cpu";
compatible = "arm,cortex-a57";
- reg = <0x0 0x100>;
+ reg = <0x100>;
clocks = <&clockgen 1 1>;
+ next-level-cache = <&cluster1_l2>;
};
cpu@101 {
device_type = "cpu";
compatible = "arm,cortex-a57";
- reg = <0x0 0x101>;
+ reg = <0x101>;
clocks = <&clockgen 1 1>;
+ next-level-cache = <&cluster1_l2>;
};
cpu@200 {
device_type = "cpu";
compatible = "arm,cortex-a57";
- reg = <0x0 0x200>;
+ reg = <0x200>;
clocks = <&clockgen 1 2>;
+ next-level-cache = <&cluster2_l2>;
};
cpu@201 {
device_type = "cpu";
compatible = "arm,cortex-a57";
- reg = <0x0 0x201>;
+ reg = <0x201>;
clocks = <&clockgen 1 2>;
+ next-level-cache = <&cluster2_l2>;
};
cpu@300 {
device_type = "cpu";
compatible = "arm,cortex-a57";
- reg = <0x0 0x300>;
+ reg = <0x300>;
clocks = <&clockgen 1 3>;
+ next-level-cache = <&cluster3_l2>;
};
cpu@301 {
device_type = "cpu";
compatible = "arm,cortex-a57";
- reg = <0x0 0x301>;
+ reg = <0x301>;
clocks = <&clockgen 1 3>;
+ next-level-cache = <&cluster3_l2>;
+ };
+
+ cluster0_l2: l2-cache0 {
+ compatible = "cache";
+ };
+
+ cluster1_l2: l2-cache1 {
+ compatible = "cache";
+ };
+
+ cluster2_l2: l2-cache2 {
+ compatible = "cache";
+ };
+
+ cluster3_l2: l2-cache3 {
+ compatible = "cache";
};
};
interrupts = <0 80 0x4>; /* Level high type */
dr_mode = "host";
snps,quirk-frame-length-adjustment = <0x20>;
+ snps,dis_rxdet_inp3_quirk;
};
usb1: usb3@3110000 {
interrupts = <0 81 0x4>; /* Level high type */
dr_mode = "host";
snps,quirk-frame-length-adjustment = <0x20>;
+ snps,dis_rxdet_inp3_quirk;
};
ccn@4000000 {
status = "ok";
};
+ /*
+ * Legend: proper name = the GPIO line is used as GPIO
+ * NC = not connected (not routed from the SoC)
+ * "[PER]" = pin is muxed for peripheral (not GPIO)
+ * "" = no idea, schematic doesn't say, could be
+ * unrouted (not connected to any external pin)
+ * LSEC = Low Speed External Connector
+ * HSEC = High Speed External Connector
+ *
+ * Pin assignments taken from LeMaker and CircuitCo Schematics
+ * Rev A1.
+ *
+ * For the lines routed to the external connectors the
+ * lines are named after the 96Boards CE Specification 1.0,
+ * Appendix "Expansion Connector Signal Description".
+ *
+ * When the 96Board naming of a line and the schematic name of
+ * the same line are in conflict, the 96Board specification
+ * takes precedence, which means that the external UART on the
+ * LSEC is named UART0 while the schematic and SoC names this
+ * UART2. This is only for the informational lines i.e. "[FOO]",
+ * the GPIO named lines "GPIO-A" thru "GPIO-L" are the only
+ * ones actually used for GPIO.
+ */
+ gpio0: gpio@f8011000 {
+ gpio-line-names = "PWR_HOLD", "DSI_SEL",
+ "USB_HUB_RESET_N", "USB_SEL", "HDMI_PD", "WL_REG_ON",
+ "PWRON_DET", "5V_HUB_EN";
+ };
+
+ gpio1: gpio@f8012000 {
+ gpio-line-names = "SD_DET", "HDMI_INT", "PMU_IRQ_N",
+ "WL_HOST_WAKE", "NC", "NC", "NC", "BT_REG_ON";
+ };
+
+ gpio2: gpio@f8013000 {
+ gpio-line-names =
+ "GPIO-A", /* LSEC Pin 23: GPIO2_0 */
+ "GPIO-B", /* LSEC Pin 24: GPIO2_1 */
+ "GPIO-C", /* LSEC Pin 25: GPIO2_2 */
+ "GPIO-D", /* LSEC Pin 26: GPIO2_3 */
+ "GPIO-E", /* LSEC Pin 27: GPIO2_4 */
+ "USB_ID_DET", "USB_VBUS_DET",
+ "GPIO-H"; /* LSEC Pin 30: GPIO2_7 */
+ };
+
+ gpio3: gpio@f8014000 {
+ gpio-line-names = "GPIO3_0", "NC", "NC", "", "NC", "",
+ "WLAN_ACTIVE", "NC", "NC";
+ };
+
+ gpio4: gpio@f7020000 {
+ gpio-line-names = "USER_LED1", "USER_LED2", "USER_LED3",
+ "USER_LED4", "SD_SEL", "NC", "NC", "BT_ACTIVE";
+ };
+
+ gpio5: gpio@f7021000 {
+ gpio-line-names = "NC", "NC",
+ "[UART1_RxD]", /* LSEC Pin 11: UART3_RX */
+ "[UART1_TxD]", /* LSEC Pin 13: UART3_TX */
+ "[AUX_SSI1]", "NC",
+ "[PCM_CLK]", /* LSEC Pin 18: MODEM_PCM_XCLK */
+ "[PCM_FS]"; /* LSEC Pin 16: MODEM_PCM_XFS */
+ };
+
+ gpio6: gpio@f7022000 {
+ gpio-line-names =
+ "[SPI0_DIN]", /* Pin 10: SPI0_DI */
+ "[SPI0_DOUT]", /* Pin 14: SPI0_DO */
+ "[SPI0_CS]", /* Pin 12: SPI0_CS_N */
+ "[SPI0_SCLK]", /* Pin 8: SPI0_SCLK */
+ "NC", "NC", "NC",
+ "GPIO-G"; /* Pin 29: GPIO6_7_DSI_TE0 */
+ };
+
+ gpio7: gpio@f7023000 {
+ gpio-line-names = "NC", "NC", "NC", "NC",
+ "[PCM_DI]", /* Pin 22: MODEM_PCM_DI */
+ "[PCM_DO]", /* Pin 20: MODEM_PCM_DO */
+ "NC", "NC";
+ };
+
+ gpio8: gpio@f7024000 {
+ gpio-line-names = "NC", "[CEC_CLK_19_2MHZ]", "NC",
+ "", "", "", "", "", "";
+ };
+
+ gpio9: gpio@f7025000 {
+ gpio-line-names = "",
+ "GPIO-J", /* LSEC Pin 32: ISP_PWDN0_GPIO9_1 */
+ "GPIO-L", /* LSEC Pin 34: ISP_PWDN1_GPIO9_2 */
+ "NC", "NC", "NC", "NC", "[ISP_CCLK0]";
+ };
+
+ gpio10: gpio@f7026000 {
+ gpio-line-names = "BOOT_SEL",
+ "[ISP_CCLK1]",
+ "GPIO-I", /* LSEC Pin 31: ISP_RSTB0_GPIO10_2 */
+ "GPIO-K", /* LSEC Pin 33: ISP_RSTB1_GPIO10_3 */
+ "NC", "NC",
+ "[I2C2_SDA]", /* HSEC Pin 34: ISP0_SDA */
+ "[I2C2_SCL]"; /* HSEC Pin 32: ISP0_SCL */
+ };
+
+ gpio11: gpio@f7027000 {
+ gpio-line-names =
+ "[I2C3_SDA]", /* HSEC Pin 38: ISP1_SDA */
+ "[I2C3_SCL]", /* HSEC Pin 36: ISP1_SCL */
+ "", "NC", "NC", "NC", "", "";
+ };
+
+ gpio12: gpio@f7028000 {
+ gpio-line-names = "[BT_PCM_XFS]", "[BT_PCM_DI]",
+ "[BT_PCM_DO]",
+ "NC", "NC", "NC", "NC",
+ "GPIO-F"; /* LSEC Pin 28: BL_PWM_GPIO12_7 */
+ };
+
+ gpio13: gpio@f7029000 {
+ gpio-line-names = "[UART0_RX]", "[UART0_TX]",
+ "[BT_UART1_CTS]", "[BT_UART1_RTS]",
+ "[BT_UART1_RX]", "[BT_UART1_TX]",
+ "[UART0_CTS]", /* LSEC Pin 3: UART2_CTS_N */
+ "[UART0_RTS]"; /* LSEC Pin 9: UART2_RTS_N */
+ };
+
+ gpio14: gpio@f702a000 {
+ gpio-line-names =
+ "[UART0_RxD]", /* LSEC Pin 7: UART2_RX */
+ "[UART0_TxD]", /* LSEC Pin 5: UART2_TX */
+ "[I2C0_SCL]", /* LSEC Pin 15: I2C0_SCL */
+ "[I2C0_SDA]", /* LSEC Pin 17: I2C0_SDA */
+ "[I2C1_SCL]", /* LSEC Pin 19: I2C1_SCL */
+ "[I2C1_SDA]", /* LSEC Pin 21: I2C1_SDA */
+ "[I2C2_SCL]", "[I2C2_SDA]";
+ };
+
+ gpio15: gpio@f702b000 {
+ gpio-line-names = "", "", "", "", "", "", "NC", "";
+ };
+
+ /* GPIO blocks 16 thru 19 do not appear to be routed to pins */
+
dwmmc_2: dwmmc2@f723f000 {
ti,non-removable;
non-removable;
clock-names = "timer1", "timer2", "apb_pclk";
};
+ rtc0: rtc@f8003000 {
+ compatible = "arm,pl031", "arm,primecell";
+ reg = <0x0 0xf8003000 0x0 0x1000>;
+ interrupts = <0 12 4>;
+ clocks = <&ao_ctrl HI6220_RTC0_PCLK>;
+ clock-names = "apb_pclk";
+ };
+
+ rtc1: rtc@f8004000 {
+ compatible = "arm,pl031", "arm,primecell";
+ reg = <0x0 0xf8004000 0x0 0x1000>;
+ interrupts = <0 8 4>;
+ clocks = <&ao_ctrl HI6220_RTC1_PCLK>;
+ clock-names = "apb_pclk";
+ };
+
pmx0: pinmux@f7010000 {
compatible = "pinctrl-single";
reg = <0x0 0xf7010000 0x0 0x27c>;
dtb-$(CONFIG_ARCH_LG1K) += lg1312-ref.dtb
+dtb-$(CONFIG_ARCH_LG1K) += lg1313-ref.dtb
always := $(dtb-y)
subdir-y := $(dts-dirs)
--- /dev/null
+/*
+ * dts file for lg1313 Reference Board.
+ *
+ * Copyright (C) 2016, LG Electronics
+ */
+
+/dts-v1/;
+
+#include "lg1313.dtsi"
+
+/ {
+ #address-cells = <2>;
+ #size-cells = <1>;
+
+ model = "LG Electronics, DTV SoC LG1313 Reference Board";
+ compatible = "lge,lg1313-ref", "lge,lg1313";
+
+ aliases {
+ serial0 = &uart0;
+ serial1 = &uart1;
+ serial2 = &uart2;
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0x0 0x00000000 0x20000000>;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+};
+
+&uart0 {
+ status = "okay";
+};
--- /dev/null
+/*
+ * dts file for lg1313 SoC
+ *
+ * Copyright (C) 2016, LG Electronics
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
+/ {
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ compatible = "lge,lg1313";
+ interrupt-parent = <&gic>;
+
+ cpus {
+ #address-cells = <2>;
+ #size-cells = <0>;
+
+ cpu0: cpu@0 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53", "arm,armv8";
+ reg = <0x0 0x0>;
+ next-level-cache = <&L2_0>;
+ };
+ cpu1: cpu@1 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53", "arm,armv8";
+ reg = <0x0 0x1>;
+ enable-method = "psci";
+ next-level-cache = <&L2_0>;
+ };
+ cpu2: cpu@2 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53", "arm,armv8";
+ reg = <0x0 0x2>;
+ enable-method = "psci";
+ next-level-cache = <&L2_0>;
+ };
+ cpu3: cpu@3 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53", "arm,armv8";
+ reg = <0x0 0x3>;
+ enable-method = "psci";
+ next-level-cache = <&L2_0>;
+ };
+ L2_0: l2-cache0 {
+ compatible = "cache";
+ };
+ };
+
+ psci {
+ compatible = "arm,psci-0.2", "arm,psci";
+ method = "smc";
+ cpu_suspend = <0x84000001>;
+ cpu_off = <0x84000002>;
+ cpu_on = <0x84000003>;
+ };
+
+ gic: interrupt-controller@c0001000 {
+ #interrupt-cells = <3>;
+ compatible = "arm,gic-400";
+ interrupt-controller;
+ reg = <0x0 0xc0001000 0x1000>,
+ <0x0 0xc0002000 0x2000>,
+ <0x0 0xc0004000 0x2000>,
+ <0x0 0xc0006000 0x2000>;
+ };
+
+ pmu {
+ compatible = "arm,cortex-a53-pmu";
+ interrupts = <GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 150 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 151 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 152 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-affinity = <&cpu0>,
+ <&cpu1>,
+ <&cpu2>,
+ <&cpu3>;
+ };
+
+ timer {
+ compatible = "arm,armv8-timer";
+ interrupts = <GIC_PPI 13 (GIC_CPU_MASK_RAW(0x0f) |
+ IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 14 (GIC_CPU_MASK_RAW(0x0f) |
+ IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 11 (GIC_CPU_MASK_RAW(0x0f) |
+ IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 10 (GIC_CPU_MASK_RAW(0x0f) |
+ IRQ_TYPE_LEVEL_LOW)>;
+ };
+
+ clk_bus: clk_bus {
+ #clock-cells = <0>;
+
+ compatible = "fixed-clock";
+ clock-frequency = <198000000>;
+ clock-output-names = "BUSCLK";
+ };
+
+ soc {
+ #address-cells = <2>;
+ #size-cells = <1>;
+
+ compatible = "simple-bus";
+ interrupt-parent = <&gic>;
+ ranges;
+
+ eth0: ethernet@c3700000 {
+ compatible = "cdns,gem";
+ reg = <0x0 0xc3700000 0x1000>;
+ interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk_bus>, <&clk_bus>;
+ clock-names = "hclk", "pclk";
+ phy-mode = "rmii";
+ /* Filled in by boot */
+ mac-address = [ 00 00 00 00 00 00 ];
+ };
+ };
+
+ amba {
+ #address-cells = <2>;
+ #size-cells = <1>;
+ #interrupts-cells = <3>;
+
+ compatible = "simple-bus";
+ interrupt-parent = <&gic>;
+ ranges;
+
+ timers: timer@fd100000 {
+ compatible = "arm,sp804";
+ reg = <0x0 0xfd100000 0x1000>;
+ interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk_bus>;
+ clock-names = "apb_pclk";
+ };
+ wdog: watchdog@fd200000 {
+ compatible = "arm,sp805", "arm,primecell";
+ reg = <0x0 0xfd200000 0x1000>;
+ interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk_bus>;
+ clock-names = "apb_pclk";
+ };
+ uart0: serial@fe000000 {
+ compatible = "arm,pl011", "arm,primecell";
+ reg = <0x0 0xfe000000 0x1000>;
+ interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk_bus>;
+ clock-names = "apb_pclk";
+ status="disabled";
+ };
+ uart1: serial@fe100000 {
+ compatible = "arm,pl011", "arm,primecell";
+ reg = <0x0 0xfe100000 0x1000>;
+ interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk_bus>;
+ clock-names = "apb_pclk";
+ status="disabled";
+ };
+ uart2: serial@fe200000 {
+ compatible = "arm,pl011", "arm,primecell";
+ reg = <0x0 0xfe200000 0x1000>;
+ interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk_bus>;
+ clock-names = "apb_pclk";
+ status="disabled";
+ };
+ spi0: ssp@fe800000 {
+ compatible = "arm,pl022", "arm,primecell";
+ reg = <0x0 0xfe800000 0x1000>;
+ interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk_bus>;
+ clock-names = "apb_pclk";
+ };
+ spi1: ssp@fe900000 {
+ compatible = "arm,pl022", "arm,primecell";
+ reg = <0x0 0xfe900000 0x1000>;
+ interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk_bus>;
+ clock-names = "apb_pclk";
+ };
+ dmac0: dma@c1128000 {
+ compatible = "arm,pl330", "arm,primecell";
+ reg = <0x0 0xc1128000 0x1000>;
+ interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk_bus>;
+ clock-names = "apb_pclk";
+ };
+ gpio0: gpio@fd400000 {
+ #gpio-cells = <2>;
+ compatible = "arm,pl061", "arm,primecell";
+ gpio-controller;
+ reg = <0x0 0xfd400000 0x1000>;
+ clocks = <&clk_bus>;
+ clock-names = "apb_pclk";
+ status="disabled";
+ };
+ gpio1: gpio@fd410000 {
+ #gpio-cells = <2>;
+ compatible = "arm,pl061", "arm,primecell";
+ gpio-controller;
+ reg = <0x0 0xfd410000 0x1000>;
+ clocks = <&clk_bus>;
+ clock-names = "apb_pclk";
+ status="disabled";
+ };
+ gpio2: gpio@fd420000 {
+ #gpio-cells = <2>;
+ compatible = "arm,pl061", "arm,primecell";
+ gpio-controller;
+ reg = <0x0 0xfd420000 0x1000>;
+ clocks = <&clk_bus>;
+ clock-names = "apb_pclk";
+ status="disabled";
+ };
+ gpio3: gpio@fd430000 {
+ #gpio-cells = <2>;
+ compatible = "arm,pl061", "arm,primecell";
+ gpio-controller;
+ reg = <0x0 0xfd430000 0x1000>;
+ clocks = <&clk_bus>;
+ clock-names = "apb_pclk";
+ };
+ gpio4: gpio@fd440000 {
+ #gpio-cells = <2>;
+ compatible = "arm,pl061", "arm,primecell";
+ gpio-controller;
+ reg = <0x0 0xfd440000 0x1000>;
+ clocks = <&clk_bus>;
+ clock-names = "apb_pclk";
+ status="disabled";
+ };
+ gpio5: gpio@fd450000 {
+ #gpio-cells = <2>;
+ compatible = "arm,pl061", "arm,primecell";
+ gpio-controller;
+ reg = <0x0 0xfd450000 0x1000>;
+ clocks = <&clk_bus>;
+ clock-names = "apb_pclk";
+ status="disabled";
+ };
+ gpio6: gpio@fd460000 {
+ #gpio-cells = <2>;
+ compatible = "arm,pl061", "arm,primecell";
+ gpio-controller;
+ reg = <0x0 0xfd460000 0x1000>;
+ clocks = <&clk_bus>;
+ clock-names = "apb_pclk";
+ status="disabled";
+ };
+ gpio7: gpio@fd470000 {
+ #gpio-cells = <2>;
+ compatible = "arm,pl061", "arm,primecell";
+ gpio-controller;
+ reg = <0x0 0xfd470000 0x1000>;
+ clocks = <&clk_bus>;
+ clock-names = "apb_pclk";
+ status="disabled";
+ };
+ gpio8: gpio@fd480000 {
+ #gpio-cells = <2>;
+ compatible = "arm,pl061", "arm,primecell";
+ gpio-controller;
+ reg = <0x0 0xfd480000 0x1000>;
+ clocks = <&clk_bus>;
+ clock-names = "apb_pclk";
+ status="disabled";
+ };
+ gpio9: gpio@fd490000 {
+ #gpio-cells = <2>;
+ compatible = "arm,pl061", "arm,primecell";
+ gpio-controller;
+ reg = <0x0 0xfd490000 0x1000>;
+ clocks = <&clk_bus>;
+ clock-names = "apb_pclk";
+ status="disabled";
+ };
+ gpio10: gpio@fd4a0000 {
+ #gpio-cells = <2>;
+ compatible = "arm,pl061", "arm,primecell";
+ gpio-controller;
+ reg = <0x0 0xfd4a0000 0x1000>;
+ clocks = <&clk_bus>;
+ clock-names = "apb_pclk";
+ status="disabled";
+ };
+ gpio11: gpio@fd4b0000 {
+ #gpio-cells = <2>;
+ compatible = "arm,pl061", "arm,primecell";
+ gpio-controller;
+ reg = <0x0 0xfd4b0000 0x1000>;
+ clocks = <&clk_bus>;
+ clock-names = "apb_pclk";
+ };
+ gpio12: gpio@fd4c0000 {
+ #gpio-cells = <2>;
+ compatible = "arm,pl061", "arm,primecell";
+ gpio-controller;
+ reg = <0x0 0xfd4c0000 0x1000>;
+ clocks = <&clk_bus>;
+ clock-names = "apb_pclk";
+ status="disabled";
+ };
+ gpio13: gpio@fd4d0000 {
+ #gpio-cells = <2>;
+ compatible = "arm,pl061", "arm,primecell";
+ gpio-controller;
+ reg = <0x0 0xfd4d0000 0x1000>;
+ clocks = <&clk_bus>;
+ clock-names = "apb_pclk";
+ status="disabled";
+ };
+ gpio14: gpio@fd4e0000 {
+ #gpio-cells = <2>;
+ compatible = "arm,pl061", "arm,primecell";
+ gpio-controller;
+ reg = <0x0 0xfd4e0000 0x1000>;
+ clocks = <&clk_bus>;
+ clock-names = "apb_pclk";
+ status="disabled";
+ };
+ gpio15: gpio@fd4f0000 {
+ #gpio-cells = <2>;
+ compatible = "arm,pl061", "arm,primecell";
+ gpio-controller;
+ reg = <0x0 0xfd4f0000 0x1000>;
+ clocks = <&clk_bus>;
+ clock-names = "apb_pclk";
+ status="disabled";
+ };
+ gpio16: gpio@fd500000 {
+ #gpio-cells = <2>;
+ compatible = "arm,pl061", "arm,primecell";
+ gpio-controller;
+ reg = <0x0 0xfd500000 0x1000>;
+ clocks = <&clk_bus>;
+ clock-names = "apb_pclk";
+ status="disabled";
+ };
+ gpio17: gpio@fd510000 {
+ #gpio-cells = <2>;
+ compatible = "arm,pl061", "arm,primecell";
+ gpio-controller;
+ reg = <0x0 0xfd510000 0x1000>;
+ clocks = <&clk_bus>;
+ clock-names = "apb_pclk";
+ };
+ };
+};
status = "disabled";
};
+ nb_perih_clk: nb-periph-clk@13000{
+ compatible = "marvell,armada-3700-periph-clock-nb";
+ reg = <0x13000 0x100>;
+ clocks = <&tbg 0>, <&tbg 1>, <&tbg 2>,
+ <&tbg 3>, <&xtalclk>;
+ #clock-cells = <1>;
+ };
+
+ sb_perih_clk: sb-periph-clk@18000{
+ compatible = "marvell,armada-3700-periph-clock-sb";
+ reg = <0x18000 0x100>;
+ clocks = <&tbg 0>, <&tbg 1>, <&tbg 2>,
+ <&tbg 3>, <&xtalclk>;
+ #clock-cells = <1>;
+ };
+
+ tbg: tbg@13200 {
+ compatible = "marvell,armada-3700-tbg-clock";
+ reg = <0x13200 0x100>;
+ clocks = <&xtalclk>;
+ #clock-cells = <1>;
+ };
+
+ gpio1: gpio@13800 {
+ compatible = "marvell,mvebu-gpio-3700",
+ "syscon", "simple-mfd";
+ reg = <0x13800 0x500>;
+
+ xtalclk: xtal-clk {
+ compatible = "marvell,armada-3700-xtal-clock";
+ clock-output-names = "xtal";
+ #clock-cells = <0>;
+ };
+ };
+
usb3: usb@58000 {
compatible = "marvell,armada3700-xhci",
"generic-xhci";
};
xor@400000 {
- compatible = "marvell,mv-xor-v2";
+ compatible = "marvell,armada-7k-xor", "marvell,xor-v2";
reg = <0x400000 0x1000>,
<0x410000 0x1000>;
msi-parent = <&gic_v2m0>;
};
xor@420000 {
- compatible = "marvell,mv-xor-v2";
+ compatible = "marvell,armada-7k-xor", "marvell,xor-v2";
reg = <0x420000 0x1000>,
<0x430000 0x1000>;
msi-parent = <&gic_v2m0>;
};
xor@440000 {
- compatible = "marvell,mv-xor-v2";
+ compatible = "marvell,armada-7k-xor", "marvell,xor-v2";
reg = <0x440000 0x1000>,
<0x450000 0x1000>;
msi-parent = <&gic_v2m0>;
};
xor@460000 {
- compatible = "marvell,mv-xor-v2";
+ compatible = "marvell,armada-7k-xor", "marvell,xor-v2";
reg = <0x460000 0x1000>,
<0x470000 0x1000>;
msi-parent = <&gic_v2m0>;
status = "disabled";
};
+ cpm_xor0: xor@6a0000 {
+ compatible = "marvell,armada-7k-xor", "marvell,xor-v2";
+ reg = <0x6a0000 0x1000>,
+ <0x6b0000 0x1000>;
+ dma-coherent;
+ msi-parent = <&gic_v2m0>;
+ clocks = <&cpm_syscon0 1 8>;
+ };
+
+ cpm_xor1: xor@6c0000 {
+ compatible = "marvell,armada-7k-xor", "marvell,xor-v2";
+ reg = <0x6c0000 0x1000>,
+ <0x6d0000 0x1000>;
+ dma-coherent;
+ msi-parent = <&gic_v2m0>;
+ clocks = <&cpm_syscon0 1 7>;
+ };
+
cpm_spi0: spi@700600 {
compatible = "marvell,armada-380-spi";
reg = <0x700600 0x50>;
+dtb-$(CONFIG_ARCH_MEDIATEK) += mt6755-evb.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt6795-evb.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt8173-evb.dtb
--- /dev/null
+/*
+ * Copyright (c) 2016 MediaTek Inc.
+ * Author: Mars.C <mars.cheng@mediatek.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+/dts-v1/;
+#include "mt6755.dtsi"
+
+/ {
+ model = "MediaTek MT6755 EVB";
+ compatible = "mediatek,mt6755-evb", "mediatek,mt6755";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ memory@40000000 {
+ device_type = "memory";
+ reg = <0 0x40000000 0 0x1e800000>;
+ };
+
+ chosen {
+ stdout-path = "serial0:921600n8";
+ };
+};
+
+&uart0 {
+ status = "okay";
+};
--- /dev/null
+/*
+ * Copyright (c) 2016 MediaTek Inc.
+ * Author: Mars.C <mars.cheng@mediatek.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
+/ {
+ compatible = "mediatek,mt6755";
+ interrupt-parent = <&sysirq>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ psci {
+ compatible = "arm,psci-0.2";
+ method = "smc";
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu0: cpu@0 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ enable-method = "psci";
+ reg = <0x000>;
+ };
+
+ cpu1: cpu@1 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ enable-method = "psci";
+ reg = <0x001>;
+ };
+
+ cpu2: cpu@2 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ enable-method = "psci";
+ reg = <0x002>;
+ };
+
+ cpu3: cpu@3 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ enable-method = "psci";
+ reg = <0x003>;
+ };
+
+ cpu4: cpu@100 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ enable-method = "psci";
+ reg = <0x100>;
+ };
+
+ cpu5: cpu@101 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ enable-method = "psci";
+ reg = <0x101>;
+ };
+
+ cpu6: cpu@102 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ enable-method = "psci";
+ reg = <0x102>;
+ };
+
+ cpu7: cpu@103 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ enable-method = "psci";
+ reg = <0x103>;
+ };
+ };
+
+ uart_clk: dummy26m {
+ compatible = "fixed-clock";
+ clock-frequency = <26000000>;
+ #clock-cells = <0>;
+ };
+
+ timer {
+ compatible = "arm,armv8-timer";
+ interrupt-parent = <&gic>;
+ interrupts = <GIC_PPI 13
+ (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 14
+ (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 11
+ (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 10
+ (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>;
+ };
+
+ sysirq: intpol-controller@10200620 {
+ compatible = "mediatek,mt6755-sysirq",
+ "mediatek,mt6577-sysirq";
+ interrupt-controller;
+ #interrupt-cells = <3>;
+ interrupt-parent = <&gic>;
+ reg = <0 0x10200620 0 0x20>;
+ };
+
+ gic: interrupt-controller@10231000 {
+ compatible = "arm,gic-400";
+ #interrupt-cells = <3>;
+ interrupt-parent = <&gic>;
+ interrupt-controller;
+ reg = <0 0x10231000 0 0x1000>,
+ <0 0x10232000 0 0x2000>,
+ <0 0x10234000 0 0x2000>,
+ <0 0x10236000 0 0x2000>;
+ };
+
+ uart0: serial@11002000 {
+ compatible = "mediatek,mt6755-uart",
+ "mediatek,mt6577-uart";
+ reg = <0 0x11002000 0 0x400>;
+ interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_LOW>;
+ clocks = <&uart_clk>;
+ status = "disabled";
+ };
+
+ uart1: serial@11003000 {
+ compatible = "mediatek,mt6755-uart",
+ "mediatek,mt6577-uart";
+ reg = <0 0x11003000 0 0x400>;
+ interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_LOW>;
+ clocks = <&uart_clk>;
+ status = "disabled";
+ };
+};
#address-cells = <2>;
#size-cells = <2>;
+ aliases {
+ ovl0 = &ovl0;
+ ovl1 = &ovl1;
+ rdma0 = &rdma0;
+ rdma1 = &rdma1;
+ rdma2 = &rdma2;
+ wdma0 = &wdma0;
+ wdma1 = &wdma1;
+ color0 = &color0;
+ color1 = &color1;
+ split0 = &split0;
+ split1 = &split1;
+ dpi0 = &dpi0;
+ dsi0 = &dsi0;
+ dsi1 = &dsi1;
+ };
+
cpus {
#address-cells = <1>;
#size-cells = <0>;
#clock-cells = <1>;
};
+ mipi_tx0: mipi-dphy@10215000 {
+ compatible = "mediatek,mt8173-mipi-tx";
+ reg = <0 0x10215000 0 0x1000>;
+ clocks = <&clk26m>;
+ clock-output-names = "mipi_tx0_pll";
+ #clock-cells = <0>;
+ #phy-cells = <0>;
+ status = "disabled";
+ };
+
+ mipi_tx1: mipi-dphy@10216000 {
+ compatible = "mediatek,mt8173-mipi-tx";
+ reg = <0 0x10216000 0 0x1000>;
+ clocks = <&clk26m>;
+ clock-output-names = "mipi_tx1_pll";
+ #clock-cells = <0>;
+ #phy-cells = <0>;
+ status = "disabled";
+ };
+
gic: interrupt-controller@10220000 {
compatible = "arm,gic-400";
#interrupt-cells = <3>;
mmsys: clock-controller@14000000 {
compatible = "mediatek,mt8173-mmsys", "syscon";
reg = <0 0x14000000 0 0x1000>;
+ power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>;
#clock-cells = <1>;
};
+ ovl0: ovl@1400c000 {
+ compatible = "mediatek,mt8173-disp-ovl";
+ reg = <0 0x1400c000 0 0x1000>;
+ interrupts = <GIC_SPI 180 IRQ_TYPE_LEVEL_LOW>;
+ power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>;
+ clocks = <&mmsys CLK_MM_DISP_OVL0>;
+ iommus = <&iommu M4U_PORT_DISP_OVL0>;
+ mediatek,larb = <&larb0>;
+ };
+
+ ovl1: ovl@1400d000 {
+ compatible = "mediatek,mt8173-disp-ovl";
+ reg = <0 0x1400d000 0 0x1000>;
+ interrupts = <GIC_SPI 181 IRQ_TYPE_LEVEL_LOW>;
+ power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>;
+ clocks = <&mmsys CLK_MM_DISP_OVL1>;
+ iommus = <&iommu M4U_PORT_DISP_OVL1>;
+ mediatek,larb = <&larb4>;
+ };
+
+ rdma0: rdma@1400e000 {
+ compatible = "mediatek,mt8173-disp-rdma";
+ reg = <0 0x1400e000 0 0x1000>;
+ interrupts = <GIC_SPI 182 IRQ_TYPE_LEVEL_LOW>;
+ power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>;
+ clocks = <&mmsys CLK_MM_DISP_RDMA0>;
+ iommus = <&iommu M4U_PORT_DISP_RDMA0>;
+ mediatek,larb = <&larb0>;
+ };
+
+ rdma1: rdma@1400f000 {
+ compatible = "mediatek,mt8173-disp-rdma";
+ reg = <0 0x1400f000 0 0x1000>;
+ interrupts = <GIC_SPI 183 IRQ_TYPE_LEVEL_LOW>;
+ power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>;
+ clocks = <&mmsys CLK_MM_DISP_RDMA1>;
+ iommus = <&iommu M4U_PORT_DISP_RDMA1>;
+ mediatek,larb = <&larb4>;
+ };
+
+ rdma2: rdma@14010000 {
+ compatible = "mediatek,mt8173-disp-rdma";
+ reg = <0 0x14010000 0 0x1000>;
+ interrupts = <GIC_SPI 184 IRQ_TYPE_LEVEL_LOW>;
+ power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>;
+ clocks = <&mmsys CLK_MM_DISP_RDMA2>;
+ iommus = <&iommu M4U_PORT_DISP_RDMA2>;
+ mediatek,larb = <&larb4>;
+ };
+
+ wdma0: wdma@14011000 {
+ compatible = "mediatek,mt8173-disp-wdma";
+ reg = <0 0x14011000 0 0x1000>;
+ interrupts = <GIC_SPI 185 IRQ_TYPE_LEVEL_LOW>;
+ power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>;
+ clocks = <&mmsys CLK_MM_DISP_WDMA0>;
+ iommus = <&iommu M4U_PORT_DISP_WDMA0>;
+ mediatek,larb = <&larb0>;
+ };
+
+ wdma1: wdma@14012000 {
+ compatible = "mediatek,mt8173-disp-wdma";
+ reg = <0 0x14012000 0 0x1000>;
+ interrupts = <GIC_SPI 186 IRQ_TYPE_LEVEL_LOW>;
+ power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>;
+ clocks = <&mmsys CLK_MM_DISP_WDMA1>;
+ iommus = <&iommu M4U_PORT_DISP_WDMA1>;
+ mediatek,larb = <&larb4>;
+ };
+
+ color0: color@14013000 {
+ compatible = "mediatek,mt8173-disp-color";
+ reg = <0 0x14013000 0 0x1000>;
+ interrupts = <GIC_SPI 187 IRQ_TYPE_LEVEL_LOW>;
+ power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>;
+ clocks = <&mmsys CLK_MM_DISP_COLOR0>;
+ };
+
+ color1: color@14014000 {
+ compatible = "mediatek,mt8173-disp-color";
+ reg = <0 0x14014000 0 0x1000>;
+ interrupts = <GIC_SPI 188 IRQ_TYPE_LEVEL_LOW>;
+ power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>;
+ clocks = <&mmsys CLK_MM_DISP_COLOR1>;
+ };
+
+ aal@14015000 {
+ compatible = "mediatek,mt8173-disp-aal";
+ reg = <0 0x14015000 0 0x1000>;
+ interrupts = <GIC_SPI 189 IRQ_TYPE_LEVEL_LOW>;
+ power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>;
+ clocks = <&mmsys CLK_MM_DISP_AAL>;
+ };
+
+ gamma@14016000 {
+ compatible = "mediatek,mt8173-disp-gamma";
+ reg = <0 0x14016000 0 0x1000>;
+ interrupts = <GIC_SPI 190 IRQ_TYPE_LEVEL_LOW>;
+ power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>;
+ clocks = <&mmsys CLK_MM_DISP_GAMMA>;
+ };
+
+ merge@14017000 {
+ compatible = "mediatek,mt8173-disp-merge";
+ reg = <0 0x14017000 0 0x1000>;
+ power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>;
+ clocks = <&mmsys CLK_MM_DISP_MERGE>;
+ };
+
+ split0: split@14018000 {
+ compatible = "mediatek,mt8173-disp-split";
+ reg = <0 0x14018000 0 0x1000>;
+ power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>;
+ clocks = <&mmsys CLK_MM_DISP_SPLIT0>;
+ };
+
+ split1: split@14019000 {
+ compatible = "mediatek,mt8173-disp-split";
+ reg = <0 0x14019000 0 0x1000>;
+ power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>;
+ clocks = <&mmsys CLK_MM_DISP_SPLIT1>;
+ };
+
+ ufoe@1401a000 {
+ compatible = "mediatek,mt8173-disp-ufoe";
+ reg = <0 0x1401a000 0 0x1000>;
+ interrupts = <GIC_SPI 191 IRQ_TYPE_LEVEL_LOW>;
+ power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>;
+ clocks = <&mmsys CLK_MM_DISP_UFOE>;
+ };
+
+ dsi0: dsi@1401b000 {
+ compatible = "mediatek,mt8173-dsi";
+ reg = <0 0x1401b000 0 0x1000>;
+ interrupts = <GIC_SPI 192 IRQ_TYPE_LEVEL_LOW>;
+ power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>;
+ clocks = <&mmsys CLK_MM_DSI0_ENGINE>,
+ <&mmsys CLK_MM_DSI0_DIGITAL>,
+ <&mipi_tx0>;
+ clock-names = "engine", "digital", "hs";
+ phys = <&mipi_tx0>;
+ phy-names = "dphy";
+ status = "disabled";
+ };
+
+ dsi1: dsi@1401c000 {
+ compatible = "mediatek,mt8173-dsi";
+ reg = <0 0x1401c000 0 0x1000>;
+ interrupts = <GIC_SPI 193 IRQ_TYPE_LEVEL_LOW>;
+ power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>;
+ clocks = <&mmsys CLK_MM_DSI1_ENGINE>,
+ <&mmsys CLK_MM_DSI1_DIGITAL>,
+ <&mipi_tx1>;
+ clock-names = "engine", "digital", "hs";
+ phy = <&mipi_tx1>;
+ phy-names = "dphy";
+ status = "disabled";
+ };
+
+ dpi0: dpi@1401d000 {
+ compatible = "mediatek,mt8173-dpi";
+ reg = <0 0x1401d000 0 0x1000>;
+ interrupts = <GIC_SPI 194 IRQ_TYPE_LEVEL_LOW>;
+ power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>;
+ clocks = <&mmsys CLK_MM_DPI_PIXEL>,
+ <&mmsys CLK_MM_DPI_ENGINE>,
+ <&apmixedsys CLK_APMIXED_TVDPLL>;
+ clock-names = "pixel", "engine", "pll";
+ status = "disabled";
+ };
+
pwm0: pwm@1401e000 {
compatible = "mediatek,mt8173-disp-pwm",
"mediatek,mt6595-disp-pwm";
status = "disabled";
};
+ mutex: mutex@14020000 {
+ compatible = "mediatek,mt8173-disp-mutex";
+ reg = <0 0x14020000 0 0x1000>;
+ interrupts = <GIC_SPI 169 IRQ_TYPE_LEVEL_LOW>;
+ power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>;
+ clocks = <&mmsys CLK_MM_MUTEX_32K>;
+ };
+
larb0: larb@14021000 {
compatible = "mediatek,mt8173-smi-larb";
reg = <0 0x14021000 0 0x1000>;
clock-names = "apb", "smi";
};
+ od@14023000 {
+ compatible = "mediatek,mt8173-disp-od";
+ reg = <0 0x14023000 0 0x1000>;
+ clocks = <&mmsys CLK_MM_DISP_OD>;
+ };
+
larb4: larb@14027000 {
compatible = "mediatek,mt8173-smi-larb";
reg = <0 0x14027000 0 0x1000>;
+#include <dt-bindings/mfd/max77620.h>
+
#include "tegra210.dtsi"
/ {
compatible = "nvidia,p2180", "nvidia,tegra210";
aliases {
+ rtc0 = "/i2c@7000d000/pmic@3c";
rtc1 = "/rtc@7000e000";
serial0 = &uarta;
};
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
memory {
device_type = "memory";
reg = <0x0 0x80000000 0x1 0x0>;
status = "okay";
};
+ i2c@7000d000 {
+ status = "okay";
+ clock-frequency = <400000>;
+
+ pmic: pmic@3c {
+ compatible = "maxim,max77620";
+ reg = <0x3c>;
+ interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
+
+ #interrupt-cells = <2>;
+ interrupt-controller;
+
+ #gpio-cells = <2>;
+ gpio-controller;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&max77620_default>;
+
+ max77620_default: pinmux {
+ gpio0 {
+ pins = "gpio0";
+ function = "gpio";
+ };
+
+ gpio1 {
+ pins = "gpio1";
+ function = "fps-out";
+ drive-push-pull = <1>;
+ maxim,active-fps-source = <MAX77620_FPS_SRC_0>;
+ maxim,active-fps-power-up-slot = <7>;
+ maxim,active-fps-power-down-slot = <0>;
+ };
+
+ gpio2_3 {
+ pins = "gpio2", "gpio3";
+ function = "fps-out";
+ drive-open-drain = <1>;
+ maxim,active-fps-source = <MAX77620_FPS_SRC_0>;
+ };
+
+ gpio4 {
+ pins = "gpio4";
+ function = "32k-out1";
+ };
+
+ gpio5_6_7 {
+ pins = "gpio5", "gpio6", "gpio7";
+ function = "gpio";
+ drive-push-pull = <1>;
+ };
+ };
+
+ fps {
+ fps0 {
+ maxim,fps-event-source = <MAX77620_FPS_EVENT_SRC_EN0>;
+ maxim,suspend-fps-time-period-us = <1280>;
+ };
+
+ fps1 {
+ maxim,fps-event-source = <MAX77620_FPS_EVENT_SRC_EN1>;
+ maxim,suspend-fps-time-period-us = <1280>;
+ };
+
+ fps2 {
+ maxim,fps-event-source = <MAX77620_FPS_EVENT_SRC_EN0>;
+ };
+ };
+
+ regulators {
+ in-ldo0-1-supply = <&vdd_pre>;
+ in-ldo7-8-supply = <&vdd_pre>;
+ in-sd3-supply = <&vdd_5v0_sys>;
+
+ vdd_soc: sd0 {
+ regulator-name = "VDD_SOC";
+ regulator-min-microvolt = <600000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-enable-ramp-delay = <146>;
+ regulator-ramp-delay = <27500>;
+
+ maxim,active-fps-source = <MAX77620_FPS_SRC_1>;
+ };
+
+ vdd_ddr: sd1 {
+ regulator-name = "VDD_DDR_1V1_PMIC";
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-enable-ramp-delay = <130>;
+ regulator-ramp-delay = <27500>;
+
+ maxim,active-fps-source = <MAX77620_FPS_SRC_0>;
+ };
+
+ vdd_pre: sd2 {
+ regulator-name = "VDD_PRE_REG_1V35";
+ regulator-min-microvolt = <1350000>;
+ regulator-max-microvolt = <1350000>;
+
+ regulator-enable-ramp-delay = <176>;
+ regulator-ramp-delay = <27500>;
+
+ maxim,active-fps-source = <MAX77620_FPS_SRC_1>;
+ };
+
+ vdd_1v8: sd3 {
+ regulator-name = "VDD_1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-enable-ramp-delay = <242>;
+ regulator-ramp-delay = <27500>;
+
+ maxim,active-fps-source = <MAX77620_FPS_SRC_0>;
+ };
+
+ vdd_sys_1v2: ldo0 {
+ regulator-name = "AVDD_SYS_1V2";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-enable-ramp-delay = <26>;
+ regulator-ramp-delay = <100000>;
+
+ maxim,active-fps-source = <MAX77620_FPS_SRC_NONE>;
+ };
+
+ vdd_pex_1v05: ldo1 {
+ regulator-name = "VDD_PEX_1V05";
+ regulator-min-microvolt = <1050000>;
+ regulator-max-microvolt = <1050000>;
+
+ regulator-enable-ramp-delay = <22>;
+ regulator-ramp-delay = <100000>;
+
+ maxim,active-fps-source = <MAX77620_FPS_SRC_1>;
+ };
+
+ vddio_sdmmc: ldo2 {
+ regulator-name = "VDDIO_SDMMC";
+ /*
+ * Technically this supply should have
+ * a supported range from 1.8 - 3.3 V.
+ * However, that would cause the SDHCI
+ * driver to request 2.7 V upon access
+ * and that in turn will cause traffic
+ * to be broken. Leave it at 3.3 V for
+ * now.
+ */
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-enable-ramp-delay = <62>;
+ regulator-ramp-delay = <100000>;
+
+ maxim,active-fps-source = <MAX77620_FPS_SRC_NONE>;
+ };
+
+ vdd_cam_hv: ldo3 {
+ regulator-name = "VDD_CAM_HV";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+
+ regulator-enable-ramp-delay = <50>;
+ regulator-ramp-delay = <100000>;
+
+ maxim,active-fps-source = <MAX77620_FPS_SRC_NONE>;
+ };
+
+ vdd_rtc: ldo4 {
+ regulator-name = "VDD_RTC";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <850000>;
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-enable-ramp-delay = <22>;
+ regulator-ramp-delay = <100000>;
+
+ maxim,active-fps-source = <MAX77620_FPS_SRC_0>;
+ };
+
+ vdd_ts_hv: ldo5 {
+ regulator-name = "VDD_TS_HV";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ regulator-enable-ramp-delay = <62>;
+ regulator-ramp-delay = <100000>;
+
+ maxim,active-fps-source = <MAX77620_FPS_SRC_NONE>;
+ };
+
+ vdd_ts: ldo6 {
+ regulator-name = "VDD_TS_1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-enable-ramp-delay = <36>;
+ regulator-ramp-delay = <100000>;
+
+ maxim,active-fps-source = <MAX77620_FPS_SRC_0>;
+ maxim,active-fps-power-up-slot = <7>;
+ maxim,active-fps-power-down-slot = <0>;
+ };
+
+ avdd_1v05_pll: ldo7 {
+ regulator-name = "AVDD_1V05_PLL";
+ regulator-min-microvolt = <1050000>;
+ regulator-max-microvolt = <1050000>;
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-enable-ramp-delay = <24>;
+ regulator-ramp-delay = <100000>;
+
+ maxim,active-fps-source = <MAX77620_FPS_SRC_1>;
+ };
+
+ avdd_1v05: ldo8 {
+ regulator-name = "AVDD_SATA_HDMI_DP_1V05";
+ regulator-min-microvolt = <1050000>;
+ regulator-max-microvolt = <1050000>;
+
+ regulator-enable-ramp-delay = <22>;
+ regulator-ramp-delay = <100000>;
+
+ maxim,active-fps-source = <MAX77620_FPS_SRC_1>;
+ };
+ };
+ };
+ };
+
pmc@7000e400 {
nvidia,invert-interrupt;
};
/ {
model = "NVIDIA Jetson TX1 Developer Kit";
compatible = "nvidia,p2371-2180", "nvidia,tegra210";
+
+ host1x@50000000 {
+ dsi@54300000 {
+ status = "okay";
+
+ avdd-dsi-csi-supply = <&vdd_dsi_csi>;
+
+ panel@0 {
+ compatible = "auo,b080uan01";
+ reg = <0>;
+
+ enable-gpios = <&gpio TEGRA_GPIO(V, 2)
+ GPIO_ACTIVE_HIGH>;
+ power-supply = <&vdd_5v0_io>;
+ backlight = <&backlight>;
+ };
+ };
+ };
+
+ i2c@7000c400 {
+ backlight: backlight@2c {
+ compatible = "ti,lp8557";
+ reg = <0x2c>;
+
+ dev-ctrl = /bits/ 8 <0x80>;
+ init-brt = /bits/ 8 <0xff>;
+
+ pwm-period = <29334>;
+
+ pwms = <&pwm 0 29334>;
+ pwm-names = "lp8557";
+
+ /* 3 LED string */
+ rom_14h {
+ rom-addr = /bits/ 8 <0x14>;
+ rom-val = /bits/ 8 <0x87>;
+ };
+
+ /* boost frequency 1 MHz */
+ rom_13h {
+ rom-addr = /bits/ 8 <0x13>;
+ rom-val = /bits/ 8 <0x01>;
+ };
+ };
+ };
};
model = "NVIDIA Tegra210 P2597 I/O board";
compatible = "nvidia,p2597", "nvidia,tegra210";
+ host1x@50000000 {
+ dpaux@54040000 {
+ status = "okay";
+ };
+
+ sor@54580000 {
+ status = "okay";
+
+ avdd-io-supply = <&avdd_1v05>;
+ vdd-pll-supply = <&vdd_1v8>;
+ hdmi-supply = <&vdd_hdmi>;
+
+ nvidia,ddc-i2c-bus = <&hdmi_ddc>;
+ nvidia,hpd-gpio = <&gpio TEGRA_GPIO(CC, 1)
+ GPIO_ACTIVE_LOW>;
+ };
+ };
+
pinmux: pinmux@700008d4 {
pinctrl-names = "boot";
pinctrl-0 = <&state_boot>;
};
};
+ pwm@7000a000 {
+ status = "okay";
+ };
+
+ i2c@7000c400 {
+ status = "okay";
+ clock-frequency = <100000>;
+
+ exp1: gpio@74 {
+ compatible = "ti,tca9539";
+ reg = <0x74>;
+
+ #gpio-cells = <2>;
+ gpio-controller;
+ };
+ };
+
+ /* HDMI DDC */
+ hdmi_ddc: i2c@7000c700 {
+ status = "okay";
+ clock-frequency = <100000>;
+ };
+
+ usb@70090000 {
+ phys = <&{/padctl@7009f000/pads/usb2/lanes/usb2-0}>,
+ <&{/padctl@7009f000/pads/usb2/lanes/usb2-1}>,
+ <&{/padctl@7009f000/pads/usb2/lanes/usb2-2}>,
+ <&{/padctl@7009f000/pads/usb2/lanes/usb2-3}>,
+ <&{/padctl@7009f000/pads/pcie/lanes/pcie-6}>,
+ <&{/padctl@7009f000/pads/pcie/lanes/pcie-5}>;
+ phy-names = "usb2-0", "usb2-1", "usb2-2", "usb2-3", "usb3-0",
+ "usb3-1";
+
+ dvddio-pex-supply = <&vdd_pex_1v05>;
+ hvddio-pex-supply = <&vdd_1v8>;
+ avdd-usb-supply = <&vdd_3v3_sys>;
+ /* XXX what are these? */
+ avdd-pll-utmip-supply = <&vdd_1v8>;
+ avdd-pll-uerefe-supply = <&vdd_pex_1v05>;
+ dvdd-usb-ss-pll-supply = <&vdd_pex_1v05>;
+ hvdd-usb-ss-pll-e-supply = <&vdd_1v8>;
+
+ status = "okay";
+ };
+
+ padctl@7009f000 {
+ status = "okay";
+
+ pads {
+ usb2 {
+ status = "okay";
+
+ lanes {
+ usb2-0 {
+ nvidia,function = "xusb";
+ status = "okay";
+ };
+
+ usb2-1 {
+ nvidia,function = "xusb";
+ status = "okay";
+ };
+
+ usb2-2 {
+ nvidia,function = "xusb";
+ status = "okay";
+ };
+
+ usb2-3 {
+ nvidia,function = "xusb";
+ status = "okay";
+ };
+ };
+ };
+
+ pcie {
+ status = "okay";
+
+ lanes {
+ pcie-0 {
+ nvidia,function = "pcie-x1";
+ status = "okay";
+ };
+
+ pcie-1 {
+ nvidia,function = "pcie-x4";
+ status = "okay";
+ };
+
+ pcie-2 {
+ nvidia,function = "pcie-x4";
+ status = "okay";
+ };
+
+ pcie-3 {
+ nvidia,function = "pcie-x4";
+ status = "okay";
+ };
+
+ pcie-4 {
+ nvidia,function = "pcie-x4";
+ status = "okay";
+ };
+
+ pcie-5 {
+ nvidia,function = "usb3-ss";
+ status = "okay";
+ };
+
+ pcie-6 {
+ nvidia,function = "usb3-ss";
+ status = "okay";
+ };
+ };
+ };
+
+ sata {
+ status = "okay";
+
+ lanes {
+ sata-0 {
+ nvidia,function = "sata";
+ status = "okay";
+ };
+ };
+ };
+ };
+
+ ports {
+ usb2-0 {
+ status = "okay";
+ mode = "otg";
+ };
+
+ usb2-1 {
+ status = "okay";
+ vbus-supply = <&vdd_5v0_rtl>;
+ mode = "host";
+ };
+
+ usb2-2 {
+ status = "okay";
+ vbus-supply = <&vdd_usb_vbus>;
+ mode = "host";
+ };
+
+ usb2-3 {
+ status = "okay";
+ mode = "host";
+ };
+
+ usb3-0 {
+ nvidia,usb2-companion = <1>;
+ status = "okay";
+ };
+
+ usb3-1 {
+ nvidia,usb2-companion = <2>;
+ status = "okay";
+ };
+ };
+ };
+
/* MMC/SD */
sdhci@700b0000 {
status = "okay";
no-1-8-v;
cd-gpios = <&gpio TEGRA_GPIO(Z, 1) GPIO_ACTIVE_LOW>;
+
+ vqmmc-supply = <&vddio_sdmmc>;
+ vmmc-supply = <&vdd_3v3_sd>;
+ };
+
+ regulators {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ vdd_sys_mux: regulator@0 {
+ compatible = "regulator-fixed";
+ reg = <0>;
+ regulator-name = "VDD_SYS_MUX";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ vdd_5v0_sys: regulator@1 {
+ compatible = "regulator-fixed";
+ reg = <1>;
+ regulator-name = "VDD_5V0_SYS";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ regulator-boot-on;
+ gpio = <&pmic 1 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ vin-supply = <&vdd_sys_mux>;
+ };
+
+ vdd_3v3_sys: regulator@2 {
+ compatible = "regulator-fixed";
+ reg = <2>;
+ regulator-name = "VDD_3V3_SYS";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ gpio = <&pmic 3 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ vin-supply = <&vdd_sys_mux>;
+
+ regulator-enable-ramp-delay = <160>;
+ regulator-disable-ramp-delay = <10000>;
+ };
+
+ vdd_5v0_io: regulator@3 {
+ compatible = "regulator-fixed";
+ reg = <3>;
+ regulator-name = "VDD_5V0_IO_SYS";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ vdd_3v3_sd: regulator@4 {
+ compatible = "regulator-fixed";
+ reg = <4>;
+ regulator-name = "VDD_3V3_SD";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio TEGRA_GPIO(Z, 4) GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ vin-supply = <&vdd_3v3_sys>;
+
+ regulator-enable-ramp-delay = <472>;
+ regulator-disable-ramp-delay = <4880>;
+ };
+
+ vdd_dsi_csi: regulator@5 {
+ compatible = "regulator-fixed";
+ reg = <5>;
+ regulator-name = "AVDD_DSI_CSI_1V2";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ vin-supply = <&vdd_sys_1v2>;
+ };
+
+ vdd_3v3_dis: regulator@6 {
+ compatible = "regulator-fixed";
+ reg = <6>;
+ regulator-name = "VDD_DIS_3V3_LCD";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ gpio = <&exp1 3 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ vin-supply = <&vdd_3v3_sys>;
+ };
+
+ vdd_1v8_dis: regulator@7 {
+ compatible = "regulator-fixed";
+ reg = <7>;
+ regulator-name = "VDD_LCD_1V8_DIS";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ gpio = <&exp1 14 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ vin-supply = <&vdd_1v8>;
+ };
+
+ vdd_5v0_rtl: regulator@8 {
+ compatible = "regulator-fixed";
+ reg = <8>;
+ regulator-name = "RTL_5V";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio TEGRA_GPIO(H, 1) GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ vin-supply = <&vdd_5v0_sys>;
+ };
+
+ vdd_usb_vbus: regulator@9 {
+ compatible = "regulator-fixed";
+ reg = <9>;
+ regulator-name = "USB_VBUS_EN1";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio TEGRA_GPIO(CC, 5) GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ vin-supply = <&vdd_5v0_sys>;
+ };
+
+ vdd_hdmi: regulator@10 {
+ compatible = "regulator-fixed";
+ reg = <10>;
+ regulator-name = "VDD_HDMI_5V0";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&exp1 12 GPIO_ACTIVE_LOW>;
+ enable-active-high;
+ vin-supply = <&vdd_5v0_sys>;
+ };
};
gpio-keys {
/dts-v1/;
#include <dt-bindings/input/input.h>
+#include <dt-bindings/mfd/max77620.h>
#include <dt-bindings/pinctrl/pinctrl-tegra.h>
#include "tegra210.dtsi"
};
};
+ i2c@7000d000 {
+ status = "okay";
+ clock-frequency = <1000000>;
+
+ max77620: max77620@3c {
+ compatible = "maxim,max77620";
+ reg = <0x3c>;
+ interrupts = <0 86 IRQ_TYPE_NONE>;
+
+ #interrupt-cells = <2>;
+ interrupt-controller;
+
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&max77620_default>;
+
+ max77620_default: pinmux@0 {
+ pin_gpio {
+ pins = "gpio0", "gpio1", "gpio2", "gpio7";
+ function = "gpio";
+ };
+
+ /*
+ * GPIO3 is used to en_pp3300, and it is part of power
+ * sequence, So it must be sequenced up (automatically
+ * set by OTP) and down properly.
+ */
+ pin_gpio3 {
+ pins = "gpio3";
+ function = "fps-out";
+ drive-open-drain = <1>;
+ maxim,active-fps-source = <MAX77620_FPS_SRC_0>;
+ maxim,active-fps-power-up-slot = <4>;
+ maxim,active-fps-power-down-slot = <2>;
+ };
+
+ pin_gpio5_6 {
+ pins = "gpio5", "gpio6";
+ function = "gpio";
+ drive-push-pull = <1>;
+ };
+
+ pin_32k {
+ pins = "gpio4";
+ function = "32k-out1";
+ };
+ };
+
+ fps {
+ fps0 {
+ maxim,shutdown-fps-time-period-us = <5120>;
+ maxim,fps-event-source = <MAX77620_FPS_EVENT_SRC_EN0>;
+ };
+
+ fps1 {
+ maxim,shutdown-fps-time-period-us = <5120>;
+ maxim,fps-event-source = <MAX77620_FPS_EVENT_SRC_EN1>;
+ maxim,device-state-on-disabled-event = <MAX77620_FPS_INACTIVE_STATE_SLEEP>;
+ };
+
+ fps2 {
+ maxim,fps-event-source = <MAX77620_FPS_EVENT_SRC_EN0>;
+ };
+ };
+
+ regulators {
+ in-ldo0-1-supply = <&pp1350>;
+ in-ldo2-supply = <&pp3300>;
+ in-ldo3-5-supply = <&pp3300>;
+ in-ldo7-8-supply = <&pp1350>;
+
+ ppvar_soc: sd0 {
+ regulator-name = "PPVAR_SOC";
+ regulator-min-microvolt = <825000>;
+ regulator-max-microvolt = <1125000>;
+ regulator-always-on;
+ regulator-boot-on;
+ maxim,active-fps-source = <MAX77620_FPS_SRC_1>;
+ maxim,active-fps-power-up-slot = <1>;
+ maxim,active-fps-power-down-slot = <7>;
+ };
+
+ pp1100_sd1: sd1 {
+ regulator-name = "PP1100";
+ regulator-min-microvolt = <1125000>;
+ regulator-max-microvolt = <1125000>;
+ regulator-always-on;
+ regulator-boot-on;
+ maxim,active-fps-source = <MAX77620_FPS_SRC_0>;
+ maxim,active-fps-power-up-slot = <5>;
+ maxim,active-fps-power-down-slot = <1>;
+ };
+
+ pp1350: sd2 {
+ regulator-name = "PP1350";
+ regulator-min-microvolt = <1350000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-always-on;
+ regulator-boot-on;
+ maxim,active-fps-source = <MAX77620_FPS_SRC_NONE>;
+ maxim,active-fps-power-up-slot = <2>;
+ maxim,active-fps-power-down-slot = <5>;
+ };
+
+ pp1800: sd3 {
+ regulator-name = "PP1800";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ maxim,active-fps-source = <MAX77620_FPS_SRC_0>;
+ maxim,active-fps-power-up-slot = <3>;
+ maxim,active-fps-power-down-slot = <3>;
+ };
+
+ pp1200_avdd: ldo0 {
+ regulator-name = "PP1200_AVDD";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-enable-ramp-delay = <26>;
+ regulator-ramp-delay = <100000>;
+ regulator-boot-on;
+ maxim,active-fps-source = <MAX77620_FPS_SRC_NONE>;
+ maxim,active-fps-power-up-slot = <0>;
+ maxim,active-fps-power-down-slot = <7>;
+ };
+
+ pp1200_rcam: ldo1 {
+ regulator-name = "PP1200_RCAM";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-enable-ramp-delay = <22>;
+ regulator-ramp-delay = <100000>;
+ maxim,active-fps-source = <MAX77620_FPS_SRC_NONE>;
+ maxim,active-fps-power-up-slot = <0>;
+ maxim,active-fps-power-down-slot = <7>;
+ };
+
+ pp_ldo2: ldo2 {
+ regulator-name = "PP_LDO2";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-enable-ramp-delay = <62>;
+ regulator-ramp-delay = <11000>;
+ regulator-always-on;
+ regulator-boot-on;
+ maxim,active-fps-source = <MAX77620_FPS_SRC_NONE>;
+ maxim,active-fps-power-up-slot = <0>;
+ maxim,active-fps-power-down-slot = <7>;
+ };
+
+ pp2800l_rcam: ldo3 {
+ regulator-name = "PP2800L_RCAM";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-enable-ramp-delay = <50>;
+ regulator-ramp-delay = <100000>;
+ maxim,active-fps-source = <MAX77620_FPS_SRC_NONE>;
+ maxim,active-fps-power-up-slot = <0>;
+ maxim,active-fps-power-down-slot = <7>;
+ };
+
+ pp100_soc_rtc: ldo4 {
+ regulator-name = "PP1100_SOC_RTC";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <850000>;
+ regulator-enable-ramp-delay = <22>;
+ regulator-ramp-delay = <100000>;
+ regulator-always-on; /* Check this */
+ regulator-boot-on;
+ maxim,active-fps-source = <MAX77620_FPS_SRC_0>;
+ maxim,active-fps-power-up-slot = <1>;
+ maxim,active-fps-power-down-slot = <7>;
+ };
+
+ pp2800l_fcam: ldo5 {
+ regulator-name = "PP2800L_FCAM";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-enable-ramp-delay = <62>;
+ regulator-ramp-delay = <100000>;
+ maxim,active-fps-source = <MAX77620_FPS_SRC_NONE>;
+ maxim,active-fps-power-up-slot = <0>;
+ maxim,active-fps-power-down-slot = <7>;
+ };
+
+ ldo6 {
+ /* Unused. */
+ regulator-name = "PP_LDO6";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-enable-ramp-delay = <36>;
+ regulator-ramp-delay = <100000>;
+ maxim,active-fps-source = <MAX77620_FPS_SRC_NONE>;
+ maxim,active-fps-power-up-slot = <0>;
+ maxim,active-fps-power-down-slot = <7>;
+ };
+
+ pp1050_avdd: ldo7 {
+ regulator-name = "PP1050_AVDD";
+ regulator-min-microvolt = <1050000>;
+ regulator-max-microvolt = <1050000>;
+ regulator-enable-ramp-delay = <24>;
+ regulator-ramp-delay = <100000>;
+ regulator-always-on;
+ regulator-boot-on;
+ maxim,active-fps-source = <MAX77620_FPS_SRC_1>;
+ maxim,active-fps-power-up-slot = <3>;
+ maxim,active-fps-power-down-slot = <4>;
+ };
+
+ avddio_1v05: ldo8 {
+ regulator-name = "AVDDIO_1V05";
+ regulator-min-microvolt = <1050000>;
+ regulator-max-microvolt = <1050000>;
+ regulator-enable-ramp-delay = <22>;
+ regulator-ramp-delay = <100000>;
+ regulator-boot-on;
+ maxim,active-fps-source = <MAX77620_FPS_SRC_NONE>;
+ maxim,active-fps-power-up-slot = <0>;
+ maxim,active-fps-power-down-slot = <7>;
+ };
+ };
+ };
+ };
+
pmc@7000e400 {
nvidia,invert-interrupt;
nvidia,suspend-mode = <0>;
compatible = "arm,psci-1.0";
method = "smc";
};
+
+ regulators {
+ compatible = "simple-bus";
+ device_type = "fixed-regulators";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ppvar_sys: regulator@0 {
+ compatible = "regulator-fixed";
+ reg = <0>;
+ regulator-name = "PPVAR_SYS";
+ regulator-min-microvolt = <4400000>;
+ regulator-max-microvolt = <4400000>;
+ regulator-always-on;
+ };
+
+ pplcd_vdd: regulator@1 {
+ compatible = "regulator-fixed";
+ reg = <1>;
+ regulator-name = "PPLCD_VDD";
+ regulator-min-microvolt = <4400000>;
+ regulator-max-microvolt = <4400000>;
+ gpio = <&gpio TEGRA_GPIO(V, 4) 0>;
+ enable-active-high;
+ regulator-boot-on;
+ };
+
+ pp3000_always: regulator@2 {
+ compatible = "regulator-fixed";
+ reg = <2>;
+ regulator-name = "PP3000_ALWAYS";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-always-on;
+ };
+
+ pp3300: regulator@3 {
+ compatible = "regulator-fixed";
+ reg = <3>;
+ regulator-name = "PP3300";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ enable-active-high;
+ };
+
+ pp5000: regulator@4 {
+ compatible = "regulator-fixed";
+ reg = <4>;
+ regulator-name = "PP5000";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ };
+
+ pp1800_lcdio: regulator@5 {
+ compatible = "regulator-fixed";
+ reg = <5>;
+ regulator-name = "PP1800_LCDIO";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ gpio = <&gpio TEGRA_GPIO(V, 3) 0>;
+ enable-active-high;
+ regulator-boot-on;
+ };
+
+ pp1800_cam: regulator@6 {
+ compatible = "regulator-fixed";
+ reg= <6>;
+ regulator-name = "PP1800_CAM";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ gpio = <&gpio TEGRA_GPIO(K, 3) 0>;
+ enable-active-high;
+ };
+
+ usbc_vbus: regulator@7 {
+ compatible = "regulator-fixed";
+ reg = <7>;
+ regulator-name = "USBC_VBUS";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ };
+ };
};
resets = <&tegra_car 207>;
reset-names = "dpaux";
status = "disabled";
+
+ state_dpaux1_aux: pinmux-aux {
+ groups = "dpaux-io";
+ function = "aux";
+ };
+
+ state_dpaux1_i2c: pinmux-i2c {
+ groups = "dpaux-io";
+ function = "i2c";
+ };
+
+ state_dpaux1_off: pinmux-off {
+ groups = "dpaux-io";
+ function = "off";
+ };
+
+ i2c-bus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
};
vi@54080000 {
clock-names = "sor", "parent", "dp", "safe";
resets = <&tegra_car 182>;
reset-names = "sor";
+ pinctrl-0 = <&state_dpaux_aux>;
+ pinctrl-1 = <&state_dpaux_i2c>;
+ pinctrl-2 = <&state_dpaux_off>;
+ pinctrl-names = "aux", "i2c", "off";
status = "disabled";
};
reg = <0x0 0x54580000 0x0 0x00040000>;
interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&tegra_car TEGRA210_CLK_SOR1>,
+ <&tegra_car TEGRA210_CLK_SOR1_SRC>,
<&tegra_car TEGRA210_CLK_PLL_D2_OUT0>,
<&tegra_car TEGRA210_CLK_PLL_DP>,
<&tegra_car TEGRA210_CLK_SOR_SAFE>;
- clock-names = "sor", "parent", "dp", "safe";
+ clock-names = "sor", "source", "parent", "dp", "safe";
resets = <&tegra_car 183>;
reset-names = "sor";
+ pinctrl-0 = <&state_dpaux1_aux>;
+ pinctrl-1 = <&state_dpaux1_i2c>;
+ pinctrl-2 = <&state_dpaux1_off>;
+ pinctrl-names = "aux", "i2c", "off";
status = "disabled";
};
resets = <&tegra_car 181>;
reset-names = "dpaux";
status = "disabled";
+
+ state_dpaux_aux: pinmux-aux {
+ groups = "dpaux-io";
+ function = "aux";
+ };
+
+ state_dpaux_i2c: pinmux-i2c {
+ groups = "dpaux-io";
+ function = "i2c";
+ };
+
+ state_dpaux_off: pinmux-off {
+ groups = "dpaux-io";
+ function = "off";
+ };
+
+ i2c-bus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
};
isp@54600000 {
reset-names = "i2c";
dmas = <&apbdma 26>, <&apbdma 26>;
dma-names = "rx", "tx";
+ pinctrl-0 = <&state_dpaux1_i2c>;
+ pinctrl-1 = <&state_dpaux1_off>;
+ pinctrl-names = "default", "idle";
status = "disabled";
};
reset-names = "i2c";
dmas = <&apbdma 30>, <&apbdma 30>;
dma-names = "rx", "tx";
+ pinctrl-0 = <&state_dpaux_i2c>;
+ pinctrl-1 = <&state_dpaux_off>;
+ pinctrl-names = "default", "idle";
status = "disabled";
};
reg = <0x0 0x7000e400 0x0 0x400>;
clocks = <&tegra_car TEGRA210_CLK_PCLK>, <&clk32k_in>;
clock-names = "pclk", "clk32k_in";
+
+ powergates {
+ pd_audio: aud {
+ clocks = <&tegra_car TEGRA210_CLK_APE>,
+ <&tegra_car TEGRA210_CLK_APB2APE>;
+ resets = <&tegra_car 198>;
+ #power-domain-cells = <0>;
+ };
+
+ pd_xusbss: xusba {
+ clocks = <&tegra_car TEGRA210_CLK_XUSB_SS>;
+ clock-names = "xusb-ss";
+ resets = <&tegra_car TEGRA210_CLK_XUSB_SS>;
+ reset-names = "xusb-ss";
+ #power-domain-cells = <0>;
+ };
+
+ pd_xusbdev: xusbb {
+ clocks = <&tegra_car TEGRA210_CLK_XUSB_DEV>;
+ clock-names = "xusb-dev";
+ resets = <&tegra_car 95>;
+ reset-names = "xusb-dev";
+ #power-domain-cells = <0>;
+ };
+
+ pd_xusbhost: xusbc {
+ clocks = <&tegra_car TEGRA210_CLK_XUSB_HOST>;
+ clock-names = "xusb-host";
+ resets = <&tegra_car TEGRA210_CLK_XUSB_HOST>;
+ reset-names = "xusb-host";
+ #power-domain-cells = <0>;
+ };
+ };
};
fuse@7000f800 {
status = "disabled";
};
+ usb@70090000 {
+ compatible = "nvidia,tegra210-xusb";
+ reg = <0x0 0x70090000 0x0 0x8000>,
+ <0x0 0x70098000 0x0 0x1000>,
+ <0x0 0x70099000 0x0 0x1000>;
+ reg-names = "hcd", "fpci", "ipfs";
+
+ interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>;
+
+ clocks = <&tegra_car TEGRA210_CLK_XUSB_HOST>,
+ <&tegra_car TEGRA210_CLK_XUSB_HOST_SRC>,
+ <&tegra_car TEGRA210_CLK_XUSB_FALCON_SRC>,
+ <&tegra_car TEGRA210_CLK_XUSB_SS>,
+ <&tegra_car TEGRA210_CLK_XUSB_SS_DIV2>,
+ <&tegra_car TEGRA210_CLK_XUSB_SS_SRC>,
+ <&tegra_car TEGRA210_CLK_XUSB_HS_SRC>,
+ <&tegra_car TEGRA210_CLK_XUSB_FS_SRC>,
+ <&tegra_car TEGRA210_CLK_PLL_U_480M>,
+ <&tegra_car TEGRA210_CLK_CLK_M>,
+ <&tegra_car TEGRA210_CLK_PLL_E>;
+ clock-names = "xusb_host", "xusb_host_src",
+ "xusb_falcon_src", "xusb_ss",
+ "xusb_ss_div2", "xusb_ss_src",
+ "xusb_hs_src", "xusb_fs_src",
+ "pll_u_480m", "clk_m", "pll_e";
+ resets = <&tegra_car 89>, <&tegra_car 156>,
+ <&tegra_car 143>;
+ reset-names = "xusb_host", "xusb_ss", "xusb_src";
+
+ nvidia,xusb-padctl = <&padctl>;
+
+ status = "disabled";
+ };
+
+ padctl: padctl@7009f000 {
+ compatible = "nvidia,tegra210-xusb-padctl";
+ reg = <0x0 0x7009f000 0x0 0x1000>;
+ resets = <&tegra_car 142>;
+ reset-names = "padctl";
+
+ status = "disabled";
+
+ pads {
+ usb2 {
+ clocks = <&tegra_car TEGRA210_CLK_USB2_TRK>;
+ clock-names = "trk";
+ status = "disabled";
+
+ lanes {
+ usb2-0 {
+ status = "disabled";
+ #phy-cells = <0>;
+ };
+
+ usb2-1 {
+ status = "disabled";
+ #phy-cells = <0>;
+ };
+
+ usb2-2 {
+ status = "disabled";
+ #phy-cells = <0>;
+ };
+
+ usb2-3 {
+ status = "disabled";
+ #phy-cells = <0>;
+ };
+ };
+ };
+
+ hsic {
+ clocks = <&tegra_car TEGRA210_CLK_HSIC_TRK>;
+ clock-names = "trk";
+ status = "disabled";
+
+ lanes {
+ hsic-0 {
+ status = "disabled";
+ #phy-cells = <0>;
+ };
+
+ hsic-1 {
+ status = "disabled";
+ #phy-cells = <0>;
+ };
+ };
+ };
+
+ pcie {
+ clocks = <&tegra_car TEGRA210_CLK_PLL_E>;
+ clock-names = "pll";
+ resets = <&tegra_car 205>;
+ reset-names = "phy";
+ status = "disabled";
+
+ lanes {
+ pcie-0 {
+ status = "disabled";
+ #phy-cells = <0>;
+ };
+
+ pcie-1 {
+ status = "disabled";
+ #phy-cells = <0>;
+ };
+
+ pcie-2 {
+ status = "disabled";
+ #phy-cells = <0>;
+ };
+
+ pcie-3 {
+ status = "disabled";
+ #phy-cells = <0>;
+ };
+
+ pcie-4 {
+ status = "disabled";
+ #phy-cells = <0>;
+ };
+
+ pcie-5 {
+ status = "disabled";
+ #phy-cells = <0>;
+ };
+
+ pcie-6 {
+ status = "disabled";
+ #phy-cells = <0>;
+ };
+ };
+ };
+
+ sata {
+ clocks = <&tegra_car TEGRA210_CLK_PLL_E>;
+ clock-names = "pll";
+ resets = <&tegra_car 204>;
+ reset-names = "phy";
+ status = "disabled";
+
+ lanes {
+ sata-0 {
+ status = "disabled";
+ #phy-cells = <0>;
+ };
+ };
+ };
+ };
+
+ ports {
+ usb2-0 {
+ status = "disabled";
+ };
+
+ usb2-1 {
+ status = "disabled";
+ };
+
+ usb2-2 {
+ status = "disabled";
+ };
+
+ usb2-3 {
+ status = "disabled";
+ };
+
+ hsic-0 {
+ status = "disabled";
+ };
+
+ usb3-0 {
+ status = "disabled";
+ };
+
+ usb3-1 {
+ status = "disabled";
+ };
+
+ usb3-2 {
+ status = "disabled";
+ };
+
+ usb3-3 {
+ status = "disabled";
+ };
+ };
+ };
+
sdhci@700b0000 {
compatible = "nvidia,tegra210-sdhci", "nvidia,tegra124-sdhci";
reg = <0x0 0x700b0000 0x0 0x200>;
#nvidia,mipi-calibrate-cells = <1>;
};
+ aconnect@702c0000 {
+ compatible = "nvidia,tegra210-aconnect";
+ clocks = <&tegra_car TEGRA210_CLK_APE>,
+ <&tegra_car TEGRA210_CLK_APB2APE>;
+ clock-names = "ape", "apb2ape";
+ power-domains = <&pd_audio>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0x702c0000 0x0 0x702c0000 0x00040000>;
+ status = "disabled";
+ };
+
spi@70410000 {
compatible = "nvidia,tegra210-qspi";
reg = <0x0 0x70410000 0x0 0x1000>;
};
soc {
+ dma@7884000 {
+ status = "okay";
+ };
+
serial@78af000 {
label = "LS-UART0";
status = "okay";
status = "okay";
};
+ sdhci@07864000 {
+ vmmc-supply = <&pm8916_l11>;
+ vqmmc-supply = <&pm8916_l12>;
+
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on &sdc2_cd_on>;
+ pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off &sdc2_cd_off>;
+
+ cd-gpios = <&msmgpio 38 0x1>;
+ status = "okay";
+ };
+
usb@78d9000 {
extcon = <&usb_id>, <&usb_id>;
status = "okay";
#size-cells = <2>;
ranges;
- reserve_aligned@86000000 {
- reg = <0x0 0x86000000 0x0 0x0300000>;
+ tz-apps@86000000 {
+ reg = <0x0 0x86000000 0x0 0x300000>;
no-map;
};
smem_mem: smem_region@86300000 {
- reg = <0x0 0x86300000 0x0 0x0100000>;
+ reg = <0x0 0x86300000 0x0 0x100000>;
+ no-map;
+ };
+
+ hypervisor@86400000 {
+ reg = <0x0 0x86400000 0x0 0x100000>;
+ no-map;
+ };
+
+ tz@86500000 {
+ reg = <0x0 0x86500000 0x0 0x180000>;
+ no-map;
+ };
+
+ reserved@8668000 {
+ reg = <0x0 0x86680000 0x0 0x80000>;
+ no-map;
+ };
+
+ rmtfs@86700000 {
+ reg = <0x0 0x86700000 0x0 0xe0000>;
+ no-map;
+ };
+
+ rfsa@867e00000 {
+ reg = <0x0 0x867e0000 0x0 0x20000>;
+ no-map;
+ };
+
+ mpss@86800000 {
+ reg = <0x0 0x86800000 0x0 0x2b00000>;
+ no-map;
+ };
+
+ wcnss@89300000 {
+ reg = <0x0 0x89300000 0x0 0x600000>;
no-map;
};
};
compatible = "arm,cortex-a53", "arm,armv8";
reg = <0x0>;
next-level-cache = <&L2_0>;
+ enable-method = "psci";
+ cpu-idle-states = <&CPU_SPC>;
};
CPU1: cpu@1 {
compatible = "arm,cortex-a53", "arm,armv8";
reg = <0x1>;
next-level-cache = <&L2_0>;
+ enable-method = "psci";
+ cpu-idle-states = <&CPU_SPC>;
};
CPU2: cpu@2 {
compatible = "arm,cortex-a53", "arm,armv8";
reg = <0x2>;
next-level-cache = <&L2_0>;
+ enable-method = "psci";
+ cpu-idle-states = <&CPU_SPC>;
};
CPU3: cpu@3 {
compatible = "arm,cortex-a53", "arm,armv8";
reg = <0x3>;
next-level-cache = <&L2_0>;
+ enable-method = "psci";
+ cpu-idle-states = <&CPU_SPC>;
};
L2_0: l2-cache {
compatible = "cache";
cache-level = <2>;
};
+
+ idle-states {
+ CPU_SPC: spc {
+ compatible = "arm,idle-state";
+ arm,psci-suspend-param = <0x40000002>;
+ entry-latency-us = <130>;
+ exit-latency-us = <150>;
+ min-residency-us = <2000>;
+ local-timer-stop;
+ };
+ };
+ };
+
+ psci {
+ compatible = "arm,psci-1.0";
+ method = "smc";
+ };
+
+ pmu {
+ compatible = "arm,armv8-pmuv3";
+ interrupts = <GIC_PPI 7 GIC_CPU_MASK_SIMPLE(4)>;
};
timer {
hwlocks = <&tcsr_mutex 3>;
};
+ firmware {
+ scm {
+ compatible = "qcom,scm";
+ clocks = <&gcc GCC_CRYPTO_CLK>, <&gcc GCC_CRYPTO_AXI_CLK>, <&gcc GCC_CRYPTO_AHB_CLK>;
+ clock-names = "core", "bus", "iface";
+ };
+ };
+
soc: soc {
#address-cells = <1>;
#size-cells = <1>;
--- /dev/null
+/*
+ * Copyright (c) 2013-2016, The Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+&msmgpio {
+
+ blsp1_spi0_default: blsp1_spi0_default {
+ pinmux {
+ function = "blsp_spi1";
+ pins = "gpio0", "gpio1", "gpio3";
+ };
+ pinmux_cs {
+ function = "gpio";
+ pins = "gpio2";
+ };
+ pinconf {
+ pins = "gpio0", "gpio1", "gpio3";
+ drive-strength = <12>;
+ bias-disable;
+ };
+ pinconf_cs {
+ pins = "gpio2";
+ drive-strength = <16>;
+ bias-disable;
+ output-high;
+ };
+ };
+
+ blsp1_spi0_sleep: blsp1_spi0_sleep {
+ pinmux {
+ function = "gpio";
+ pins = "gpio0", "gpio1", "gpio2", "gpio3";
+ };
+ pinconf {
+ pins = "gpio0", "gpio1", "gpio2", "gpio3";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+ };
+
+ blsp1_i2c2_default: blsp1_i2c2_default {
+ pinmux {
+ function = "blsp_i2c3";
+ pins = "gpio47", "gpio48";
+ };
+ pinconf {
+ pins = "gpio47", "gpio48";
+ drive-strength = <16>;
+ bias-disable = <0>;
+ };
+ };
+
+ blsp1_i2c2_sleep: blsp1_i2c2_sleep {
+ pinmux {
+ function = "gpio";
+ pins = "gpio47", "gpio48";
+ };
+ pinconf {
+ pins = "gpio47", "gpio48";
+ drive-strength = <2>;
+ bias-disable = <0>;
+ };
+ };
+
+ blsp2_i2c0_default: blsp2_i2c0 {
+ pinmux {
+ function = "blsp_i2c7";
+ pins = "gpio55", "gpio56";
+ };
+ pinconf {
+ pins = "gpio55", "gpio56";
+ drive-strength = <16>;
+ bias-disable;
+ };
+ };
+
+ blsp2_i2c0_sleep: blsp2_i2c0_sleep {
+ pinmux {
+ function = "gpio";
+ pins = "gpio55", "gpio56";
+ };
+ pinconf {
+ pins = "gpio55", "gpio56";
+ drive-strength = <2>;
+ bias-disable;
+ };
+ };
+
+ blsp2_uart1_2pins_default: blsp2_uart1_2pins {
+ pinmux {
+ function = "blsp_uart8";
+ pins = "gpio4", "gpio5";
+ };
+ pinconf {
+ pins = "gpio4", "gpio5";
+ drive-strength = <16>;
+ bias-disable;
+ };
+ };
+
+ blsp2_uart1_2pins_sleep: blsp2_uart1_2pins_sleep {
+ pinmux {
+ function = "gpio";
+ pins = "gpio4", "gpio5";
+ };
+ pinconf {
+ pins = "gpio4", "gpio5";
+ drive-strength = <2>;
+ bias-disable;
+ };
+ };
+
+ blsp2_uart1_4pins_default: blsp2_uart1_4pins {
+ pinmux {
+ function = "blsp_uart8";
+ pins = "gpio4", "gpio5", "gpio6", "gpio7";
+ };
+
+ pinconf {
+ pins = "gpio4", "gpio5", "gpio6", "gpio7";
+ drive-strength = <16>;
+ bias-disable;
+ };
+ };
+
+ blsp2_uart1_4pins_sleep: blsp2_uart1_4pins_sleep {
+ pinmux {
+ function = "gpio";
+ pins = "gpio4", "gpio5", "gpio6", "gpio7";
+ };
+
+ pinconf {
+ pins = "gpio4", "gpiio5", "gpio6", "gpio7";
+ drive-strength = <2>;
+ bias-disable;
+ };
+ };
+
+ blsp2_i2c1_default: blsp2_i2c1 {
+ pinmux {
+ function = "blsp_i2c8";
+ pins = "gpio6", "gpio7";
+ };
+ pinconf {
+ pins = "gpio6", "gpio7";
+ drive-strength = <16>;
+ bias-disable;
+ };
+ };
+
+ blsp2_i2c1_sleep: blsp2_i2c1_sleep {
+ pinmux {
+ function = "gpio";
+ pins = "gpio6", "gpio7";
+ };
+ pinconf {
+ pins = "gpio6", "gpio7";
+ drive-strength = <2>;
+ bias-disable;
+ };
+ };
+
+ blsp2_uart2_2pins_default: blsp2_uart2_2pins {
+ pinmux {
+ function = "blsp_uart9";
+ pins = "gpio49", "gpio50";
+ };
+ pinconf {
+ pins = "gpio49", "gpio50";
+ drive-strength = <16>;
+ bias-disable;
+ };
+ };
+
+ blsp2_uart2_2pins_sleep: blsp2_uart2_2pins_sleep {
+ pinmux {
+ function = "gpio";
+ pins = "gpio49", "gpio50";
+ };
+ pinconf {
+ pins = "gpio49", "gpio50";
+ drive-strength = <2>;
+ bias-disable;
+ };
+ };
+
+ blsp2_uart2_4pins_default: blsp2_uart2_4pins {
+ pinmux {
+ function = "blsp_uart9";
+ pins = "gpio49", "gpio50", "gpio51", "gpio52";
+ };
+
+ pinconf {
+ pins = "gpio49", "gpio50", "gpio51", "gpio52";
+ drive-strength = <16>;
+ bias-disable;
+ };
+ };
+
+ blsp2_uart2_4pins_sleep: blsp2_uart2_4pins_sleep {
+ pinmux {
+ function = "gpio";
+ pins = "gpio49", "gpio50", "gpio51", "gpio52";
+ };
+
+ pinconf {
+ pins = "gpio49", "gpio50", "gpio51", "gpio52";
+ drive-strength = <2>;
+ bias-disable;
+ };
+ };
+
+ blsp2_spi5_default: blsp2_spi5_default {
+ pinmux {
+ function = "blsp_spi12";
+ pins = "gpio85", "gpio86", "gpio88";
+ };
+ pinmux_cs {
+ function = "gpio";
+ pins = "gpio87";
+ };
+ pinconf {
+ pins = "gpio85", "gpio86", "gpio88";
+ drive-strength = <12>;
+ bias-disable;
+ };
+ pinconf_cs {
+ pins = "gpio87";
+ drive-strength = <16>;
+ bias-disable;
+ output-high;
+ };
+ };
+
+ blsp2_spi5_sleep: blsp2_spi5_sleep {
+ pinmux {
+ function = "gpio";
+ pins = "gpio85", "gpio86", "gpio87", "gpio88";
+ };
+ pinconf {
+ pins = "gpio85", "gpio86", "gpio87", "gpio88";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+ };
+
+ sdc2_clk_on: sdc2_clk_on {
+ config {
+ pins = "sdc2_clk";
+ bias-disable; /* NO pull */
+ drive-strength = <16>; /* 16 MA */
+ };
+ };
+
+ sdc2_clk_off: sdc2_clk_off {
+ config {
+ pins = "sdc2_clk";
+ bias-disable; /* NO pull */
+ drive-strength = <2>; /* 2 MA */
+ };
+ };
+
+ sdc2_cmd_on: sdc2_cmd_on {
+ config {
+ pins = "sdc2_cmd";
+ bias-pull-up; /* pull up */
+ drive-strength = <10>; /* 10 MA */
+ };
+ };
+
+ sdc2_cmd_off: sdc2_cmd_off {
+ config {
+ pins = "sdc2_cmd";
+ bias-pull-up; /* pull up */
+ drive-strength = <2>; /* 2 MA */
+ };
+ };
+
+ sdc2_data_on: sdc2_data_on {
+ config {
+ pins = "sdc2_data";
+ bias-pull-up; /* pull up */
+ drive-strength = <10>; /* 10 MA */
+ };
+ };
+
+ sdc2_data_off: sdc2_data_off {
+ config {
+ pins = "sdc2_data";
+ bias-pull-up; /* pull up */
+ drive-strength = <2>; /* 2 MA */
+ };
+ };
+};
reg = <0x300000 0x90000>;
};
+ blsp1_spi0: spi@07575000 {
+ compatible = "qcom,spi-qup-v2.2.1";
+ reg = <0x07575000 0x600>;
+ interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP1_QUP1_SPI_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&blsp1_spi0_default>;
+ pinctrl-1 = <&blsp1_spi0_sleep>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ blsp2_i2c0: i2c@075b5000 {
+ compatible = "qcom,i2c-qup-v2.2.1";
+ reg = <0x075b5000 0x1000>;
+ interrupts = <GIC_SPI 101 0>;
+ clocks = <&gcc GCC_BLSP2_AHB_CLK>,
+ <&gcc GCC_BLSP2_QUP1_I2C_APPS_CLK>;
+ clock-names = "iface", "core";
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&blsp2_i2c0_default>;
+ pinctrl-1 = <&blsp2_i2c0_sleep>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
blsp2_uart1: serial@75b0000 {
compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
reg = <0x75b0000 0x1000>;
status = "disabled";
};
- pinctrl@1010000 {
+ blsp2_i2c1: i2c@075b6000 {
+ compatible = "qcom,i2c-qup-v2.2.1";
+ reg = <0x075b6000 0x1000>;
+ interrupts = <GIC_SPI 102 0>;
+ clocks = <&gcc GCC_BLSP2_AHB_CLK>,
+ <&gcc GCC_BLSP2_QUP2_I2C_APPS_CLK>;
+ clock-names = "iface", "core";
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&blsp2_i2c1_default>;
+ pinctrl-1 = <&blsp2_i2c1_sleep>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ blsp2_uart2: serial@75b1000 {
+ compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
+ reg = <0x075b1000 0x1000>;
+ interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP2_UART3_APPS_CLK>,
+ <&gcc GCC_BLSP2_AHB_CLK>;
+ clock-names = "core", "iface";
+ status = "disabled";
+ };
+
+ blsp1_i2c2: i2c@07577000 {
+ compatible = "qcom,i2c-qup-v2.2.1";
+ reg = <0x07577000 0x1000>;
+ interrupts = <GIC_SPI 97 0>;
+ clocks = <&gcc GCC_BLSP1_AHB_CLK>,
+ <&gcc GCC_BLSP1_QUP3_I2C_APPS_CLK>;
+ clock-names = "iface", "core";
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&blsp1_i2c2_default>;
+ pinctrl-1 = <&blsp1_i2c2_sleep>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ blsp2_spi5: spi@075ba000{
+ compatible = "qcom,spi-qup-v2.2.1";
+ reg = <0x075ba000 0x600>;
+ interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP2_QUP5_SPI_APPS_CLK>,
+ <&gcc GCC_BLSP2_AHB_CLK>;
+ clock-names = "core", "iface";
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&blsp2_spi5_default>;
+ pinctrl-1 = <&blsp2_spi5_sleep>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ sdhc2: sdhci@74a4900 {
+ status = "disabled";
+ compatible = "qcom,sdhci-msm-v4";
+ reg = <0x74a4900 0x314>, <0x74a4000 0x800>;
+ reg-names = "hc_mem", "core_mem";
+
+ interrupts = <0 125 0>, <0 221 0>;
+ interrupt-names = "hc_irq", "pwr_irq";
+
+ clock-names = "iface", "core";
+ clocks = <&gcc GCC_SDCC2_AHB_CLK>,
+ <&gcc GCC_SDCC2_APPS_CLK>;
+ bus-width = <4>;
+ };
+
+ msmgpio: pinctrl@1010000 {
compatible = "qcom,msm8996-pinctrl";
reg = <0x01010000 0x300000>;
interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
};
};
};
+#include "msm8996-pins.dtsi"
dtb-$(CONFIG_ARCH_R8A7795) += r8a7795-salvator-x.dtb
+dtb-$(CONFIG_ARCH_R8A7796) += r8a7796-salvator-x.dtb
always := $(dtb-y)
clean-files := *.dtb
clock-frequency = <24576000>;
};
- vcc_sdhi0: regulator@1 {
+ vcc_sdhi0: regulator-vcc-sdhi0 {
compatible = "regulator-fixed";
regulator-name = "SDHI0 Vcc";
enable-active-high;
};
- vccq_sdhi0: regulator@2 {
+ vccq_sdhi0: regulator-vccq-sdhi0 {
compatible = "regulator-gpio";
regulator-name = "SDHI0 VccQ";
1800000 0>;
};
- vcc_sdhi3: regulator@3 {
+ vcc_sdhi3: regulator-vcc-sdhi3 {
compatible = "regulator-fixed";
regulator-name = "SDHI3 Vcc";
enable-active-high;
};
- vccq_sdhi3: regulator@4 {
+ vccq_sdhi3: regulator-vccq-sdhi3 {
compatible = "regulator-gpio";
regulator-name = "SDHI3 VccQ";
pinctrl-0 = <&scif1_pins>;
pinctrl-names = "default";
+ uart-has-rtscts;
status = "okay";
};
shared-pin;
};
+&wdt0 {
+ timeout-sec = <60>;
+ status = "okay";
+};
+
&audio_clk_a {
clock-frequency = <22579200>;
};
next-level-cache = <&L2_CA57>;
enable-method = "psci";
};
+
a57_2: cpu@2 {
compatible = "arm,cortex-a57","arm,armv8";
reg = <0x2>;
next-level-cache = <&L2_CA57>;
enable-method = "psci";
};
+
a57_3: cpu@3 {
compatible = "arm,cortex-a57","arm,armv8";
reg = <0x3>;
next-level-cache = <&L2_CA57>;
enable-method = "psci";
};
- };
- L2_CA57: cache-controller@0 {
- compatible = "cache";
- power-domains = <&sysc R8A7795_PD_CA57_SCU>;
- cache-unified;
- cache-level = <2>;
- };
+ L2_CA57: cache-controller@0 {
+ compatible = "cache";
+ reg = <0>;
+ power-domains = <&sysc R8A7795_PD_CA57_SCU>;
+ cache-unified;
+ cache-level = <2>;
+ };
- L2_CA53: cache-controller@1 {
- compatible = "cache";
- power-domains = <&sysc R8A7795_PD_CA53_SCU>;
- cache-unified;
- cache-level = <2>;
+ L2_CA53: cache-controller@100 {
+ compatible = "cache";
+ reg = <0x100>;
+ power-domains = <&sysc R8A7795_PD_CA53_SCU>;
+ cache-unified;
+ cache-level = <2>;
+ };
};
extal_clk: extal {
#size-cells = <2>;
ranges;
- gic: interrupt-controller@0xf1010000 {
+ gic: interrupt-controller@f1010000 {
compatible = "arm,gic-400";
#interrupt-cells = <3>;
#address-cells = <0>;
interrupt-controller;
reg = <0x0 0xf1010000 0 0x1000>,
- <0x0 0xf1020000 0 0x2000>,
+ <0x0 0xf1020000 0 0x20000>,
<0x0 0xf1040000 0 0x20000>,
- <0x0 0xf1060000 0 0x2000>;
+ <0x0 0xf1060000 0 0x20000>;
interrupts = <GIC_PPI 9
(GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
};
+ wdt0: watchdog@e6020000 {
+ compatible = "renesas,r8a7795-wdt", "renesas,rcar-gen3-wdt";
+ reg = <0 0xe6020000 0 0x0c>;
+ clocks = <&cpg CPG_MOD 402>;
+ power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
+ status = "disabled";
+ };
+
gpio0: gpio@e6050000 {
compatible = "renesas,gpio-r8a7795",
"renesas,gpio-rcar";
status = "disabled";
};
+ canfd: can@e66c0000 {
+ compatible = "renesas,r8a7795-canfd",
+ "renesas,rcar-gen3-canfd";
+ reg = <0 0xe66c0000 0 0x8000>;
+ interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cpg CPG_MOD 914>,
+ <&cpg CPG_CORE R8A7795_CLK_CANFD>,
+ <&can_clk>;
+ clock-names = "fck", "canfd", "can_clk";
+ assigned-clocks = <&cpg CPG_CORE R8A7795_CLK_CANFD>;
+ assigned-clock-rates = <40000000>;
+ power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
+ status = "disabled";
+
+ channel0 {
+ status = "disabled";
+ };
+
+ channel1 {
+ status = "disabled";
+ };
+ };
+
hscif0: serial@e6540000 {
compatible = "renesas,hscif-r8a7795",
"renesas,rcar-gen3-hscif",
interrupts = <GIC_SPI 287 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 931>;
power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
+ dmas = <&dmac1 0x91>, <&dmac1 0x90>;
+ dma-names = "tx", "rx";
i2c-scl-internal-delay-ns = <110>;
status = "disabled";
};
interrupts = <GIC_SPI 288 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 930>;
power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
+ dmas = <&dmac1 0x93>, <&dmac1 0x92>;
+ dma-names = "tx", "rx";
i2c-scl-internal-delay-ns = <6>;
status = "disabled";
};
interrupts = <GIC_SPI 286 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 929>;
power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
+ dmas = <&dmac1 0x95>, <&dmac1 0x94>;
+ dma-names = "tx", "rx";
i2c-scl-internal-delay-ns = <6>;
status = "disabled";
};
interrupts = <GIC_SPI 290 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 928>;
power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
+ dmas = <&dmac0 0x97>, <&dmac0 0x96>;
+ dma-names = "tx", "rx";
i2c-scl-internal-delay-ns = <110>;
status = "disabled";
};
interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 927>;
power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
+ dmas = <&dmac0 0x99>, <&dmac0 0x98>;
+ dma-names = "tx", "rx";
i2c-scl-internal-delay-ns = <110>;
status = "disabled";
};
interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 919>;
power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
+ dmas = <&dmac0 0x9b>, <&dmac0 0x9a>;
+ dma-names = "tx", "rx";
i2c-scl-internal-delay-ns = <110>;
status = "disabled";
};
interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 918>;
power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
+ dmas = <&dmac0 0x9d>, <&dmac0 0x9c>;
+ dma-names = "tx", "rx";
i2c-scl-internal-delay-ns = <6>;
status = "disabled";
};
status = "disabled";
rcar_sound,dvc {
- dvc0: dvc@0 {
+ dvc0: dvc-0 {
dmas = <&audma0 0xbc>;
dma-names = "tx";
};
- dvc1: dvc@1 {
+ dvc1: dvc-1 {
dmas = <&audma0 0xbe>;
dma-names = "tx";
};
};
rcar_sound,src {
- src0: src@0 {
+ src0: src-0 {
interrupts = <GIC_SPI 352 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&audma0 0x85>, <&audma1 0x9a>;
dma-names = "rx", "tx";
};
- src1: src@1 {
+ src1: src-1 {
interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&audma0 0x87>, <&audma1 0x9c>;
dma-names = "rx", "tx";
};
- src2: src@2 {
+ src2: src-2 {
interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&audma0 0x89>, <&audma1 0x9e>;
dma-names = "rx", "tx";
};
- src3: src@3 {
+ src3: src-3 {
interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&audma0 0x8b>, <&audma1 0xa0>;
dma-names = "rx", "tx";
};
- src4: src@4 {
+ src4: src-4 {
interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&audma0 0x8d>, <&audma1 0xb0>;
dma-names = "rx", "tx";
};
- src5: src@5 {
+ src5: src-5 {
interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&audma0 0x8f>, <&audma1 0xb2>;
dma-names = "rx", "tx";
};
- src6: src@6 {
+ src6: src-6 {
interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&audma0 0x91>, <&audma1 0xb4>;
dma-names = "rx", "tx";
};
- src7: src@7 {
+ src7: src-7 {
interrupts = <GIC_SPI 359 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&audma0 0x93>, <&audma1 0xb6>;
dma-names = "rx", "tx";
};
- src8: src@8 {
+ src8: src-8 {
interrupts = <GIC_SPI 360 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&audma0 0x95>, <&audma1 0xb8>;
dma-names = "rx", "tx";
};
- src9: src@9 {
+ src9: src-9 {
interrupts = <GIC_SPI 361 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&audma0 0x97>, <&audma1 0xba>;
dma-names = "rx", "tx";
};
rcar_sound,ssi {
- ssi0: ssi@0 {
+ ssi0: ssi-0 {
interrupts = <GIC_SPI 370 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&audma0 0x01>, <&audma1 0x02>, <&audma0 0x15>, <&audma1 0x16>;
dma-names = "rx", "tx", "rxu", "txu";
};
- ssi1: ssi@1 {
+ ssi1: ssi-1 {
interrupts = <GIC_SPI 371 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&audma0 0x03>, <&audma1 0x04>, <&audma0 0x49>, <&audma1 0x4a>;
dma-names = "rx", "tx", "rxu", "txu";
};
- ssi2: ssi@2 {
+ ssi2: ssi-2 {
interrupts = <GIC_SPI 372 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&audma0 0x05>, <&audma1 0x06>, <&audma0 0x63>, <&audma1 0x64>;
dma-names = "rx", "tx", "rxu", "txu";
};
- ssi3: ssi@3 {
+ ssi3: ssi-3 {
interrupts = <GIC_SPI 373 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&audma0 0x07>, <&audma1 0x08>, <&audma0 0x6f>, <&audma1 0x70>;
dma-names = "rx", "tx", "rxu", "txu";
};
- ssi4: ssi@4 {
+ ssi4: ssi-4 {
interrupts = <GIC_SPI 374 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&audma0 0x09>, <&audma1 0x0a>, <&audma0 0x71>, <&audma1 0x72>;
dma-names = "rx", "tx", "rxu", "txu";
};
- ssi5: ssi@5 {
+ ssi5: ssi-5 {
interrupts = <GIC_SPI 375 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&audma0 0x0b>, <&audma1 0x0c>, <&audma0 0x73>, <&audma1 0x74>;
dma-names = "rx", "tx", "rxu", "txu";
};
- ssi6: ssi@6 {
+ ssi6: ssi-6 {
interrupts = <GIC_SPI 376 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&audma0 0x0d>, <&audma1 0x0e>, <&audma0 0x75>, <&audma1 0x76>;
dma-names = "rx", "tx", "rxu", "txu";
};
- ssi7: ssi@7 {
+ ssi7: ssi-7 {
interrupts = <GIC_SPI 377 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&audma0 0x0f>, <&audma1 0x10>, <&audma0 0x79>, <&audma1 0x7a>;
dma-names = "rx", "tx", "rxu", "txu";
};
- ssi8: ssi@8 {
+ ssi8: ssi-8 {
interrupts = <GIC_SPI 378 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&audma0 0x11>, <&audma1 0x12>, <&audma0 0x7b>, <&audma1 0x7c>;
dma-names = "rx", "tx", "rxu", "txu";
};
- ssi9: ssi@9 {
+ ssi9: ssi-9 {
interrupts = <GIC_SPI 379 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&audma0 0x13>, <&audma1 0x14>, <&audma0 0x7d>, <&audma1 0x7e>;
dma-names = "rx", "tx", "rxu", "txu";
--- /dev/null
+/*
+ * Device Tree Source for the Salvator-X board
+ *
+ * Copyright (C) 2016 Renesas Electronics Corp.
+ *
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2. This program is licensed "as is" without any warranty of any
+ * kind, whether express or implied.
+ */
+
+/dts-v1/;
+#include "r8a7796.dtsi"
+
+/ {
+ model = "Renesas Salvator-X board based on r8a7796";
+ compatible = "renesas,salvator-x", "renesas,r8a7796";
+
+ aliases {
+ serial0 = &scif2;
+ };
+
+ chosen {
+ bootargs = "ignore_loglevel";
+ stdout-path = "serial0:115200n8";
+ };
+
+ memory@48000000 {
+ device_type = "memory";
+ /* first 128MB is reserved for secure area. */
+ reg = <0x0 0x48000000 0x0 0x78000000>;
+ };
+};
+
+&extal_clk {
+ clock-frequency = <16666666>;
+};
+
+&scif2 {
+ status = "okay";
+};
+
+&scif_clk {
+ clock-frequency = <14745600>;
+ status = "okay";
+};
+
+&wdt0 {
+ timeout-sec = <60>;
+ status = "okay";
+};
--- /dev/null
+/*
+ * Device Tree Source for the r8a7796 SoC
+ *
+ * Copyright (C) 2016 Renesas Electronics Corp.
+ *
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2. This program is licensed "as is" without any warranty of any
+ * kind, whether express or implied.
+ */
+
+#include <dt-bindings/clock/r8a7796-cpg-mssr.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/power/r8a7796-sysc.h>
+
+/ {
+ compatible = "renesas,r8a7796";
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ psci {
+ compatible = "arm,psci-0.2";
+ method = "smc";
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /* 1 core only at this point */
+ a57_0: cpu@0 {
+ compatible = "arm,cortex-a57", "arm,armv8";
+ reg = <0x0>;
+ device_type = "cpu";
+ power-domains = <&sysc R8A7796_PD_CA57_CPU0>;
+ next-level-cache = <&L2_CA57>;
+ enable-method = "psci";
+ };
+
+ L2_CA57: cache-controller@0 {
+ compatible = "cache";
+ reg = <0>;
+ power-domains = <&sysc R8A7796_PD_CA57_SCU>;
+ cache-unified;
+ cache-level = <2>;
+ };
+ };
+
+ extal_clk: extal {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ /* This value must be overridden by the board */
+ clock-frequency = <0>;
+ };
+
+ extalr_clk: extalr {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ /* This value must be overridden by the board */
+ clock-frequency = <0>;
+ };
+
+ /* External SCIF clock - to be overridden by boards that provide it */
+ scif_clk: scif {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <0>;
+ };
+
+ soc {
+ compatible = "simple-bus";
+ interrupt-parent = <&gic>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ gic: interrupt-controller@f1010000 {
+ compatible = "arm,gic-400";
+ #interrupt-cells = <3>;
+ #address-cells = <0>;
+ interrupt-controller;
+ reg = <0x0 0xf1010000 0 0x1000>,
+ <0x0 0xf1020000 0 0x20000>,
+ <0x0 0xf1040000 0 0x20000>,
+ <0x0 0xf1060000 0 0x20000>;
+ interrupts = <GIC_PPI 9
+ (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_HIGH)>;
+ };
+
+ timer {
+ compatible = "arm,armv8-timer";
+ interrupts = <GIC_PPI 13
+ (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 14
+ (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 11
+ (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 10
+ (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>;
+ };
+
+ wdt0: watchdog@e6020000 {
+ compatible = "renesas,r8a7796-wdt",
+ "renesas,rcar-gen3-wdt";
+ reg = <0 0xe6020000 0 0x0c>;
+ clocks = <&cpg CPG_MOD 402>;
+ power-domains = <&sysc R8A7796_PD_ALWAYS_ON>;
+ status = "disabled";
+ };
+
+ cpg: clock-controller@e6150000 {
+ compatible = "renesas,r8a7796-cpg-mssr";
+ reg = <0 0xe6150000 0 0x1000>;
+ clocks = <&extal_clk>, <&extalr_clk>;
+ clock-names = "extal", "extalr";
+ #clock-cells = <2>;
+ #power-domain-cells = <0>;
+ };
+
+ sysc: system-controller@e6180000 {
+ compatible = "renesas,r8a7796-sysc";
+ reg = <0 0xe6180000 0 0x0400>;
+ #power-domain-cells = <1>;
+ };
+
+ scif2: serial@e6e88000 {
+ compatible = "renesas,scif-r8a7796",
+ "renesas,rcar-gen3-scif", "renesas,scif";
+ reg = <0 0xe6e88000 0 64>;
+ interrupts = <GIC_SPI 164 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cpg CPG_MOD 310>,
+ <&cpg CPG_CORE R8A7796_CLK_S3D1>,
+ <&scif_clk>;
+ clock-names = "fck", "brg_int", "scif_clk";
+ power-domains = <&sysc R8A7796_PD_ALWAYS_ON>;
+ status = "disabled";
+ };
+ };
+};
};
};
+&io_domains {
+ status = "ok";
+
+ audio-supply = <&vcc_io>;
+ gpio30-supply = <&vcc_io>;
+ gpio1830-supply = <&vcc_io>;
+ wifi-supply = <&vccio_wl>;
+};
+
&sdio0 {
assigned-clocks = <&cru SCLK_SDIO0>;
assigned-clock-parents = <&cru PLL_CPLL>;
};
};
+&pmu_io_domains {
+ status = "okay";
+
+ pmu-supply = <&vcc_io>;
+ vop-supply = <&vcc_io>;
+};
+
&saradc {
vref-supply = <&vcc_18>;
status = "okay";
};
pmugrf: syscon@ff738000 {
- compatible = "rockchip,rk3368-pmugrf", "syscon";
+ compatible = "rockchip,rk3368-pmugrf", "syscon", "simple-mfd";
reg = <0x0 0xff738000 0x0 0x1000>;
+
+ pmu_io_domains: io-domains {
+ compatible = "rockchip,rk3368-pmu-io-voltage-domain";
+ status = "disabled";
+ };
};
cru: clock-controller@ff760000 {
};
grf: syscon@ff770000 {
- compatible = "rockchip,rk3368-grf", "syscon";
+ compatible = "rockchip,rk3368-grf", "syscon", "simple-mfd";
reg = <0x0 0xff770000 0x0 0x1000>;
+
+ io_domains: io-domains {
+ compatible = "rockchip,rk3368-io-voltage-domain";
+ status = "disabled";
+ };
};
wdt: watchdog@ff800000 {
#address-cells = <0>;
reg = <0x0 0xffb71000 0x0 0x1000>,
- <0x0 0xffb72000 0x0 0x1000>,
+ <0x0 0xffb72000 0x0 0x2000>,
<0x0 0xffb74000 0x0 0x2000>,
<0x0 0xffb76000 0x0 0x2000>;
interrupts = <GIC_PPI 9
};
};
+&emmc_phy {
+ status = "okay";
+};
+
&pwm0 {
status = "okay";
};
status = "okay";
};
+&sdhci {
+ bus-width = <8>;
+ mmc-hs400-1_8v;
+ mmc-hs400-enhanced-strobe;
+ non-removable;
+ status = "okay";
+};
+
&uart2 {
status = "okay";
};
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/pinctrl/rockchip.h>
+#include <dt-bindings/thermal/thermal.h>
/ {
compatible = "rockchip,rk3399";
#size-cells = <2>;
aliases {
+ i2c0 = &i2c0;
+ i2c1 = &i2c1;
+ i2c2 = &i2c2;
+ i2c3 = &i2c3;
+ i2c4 = &i2c4;
+ i2c5 = &i2c5;
+ i2c6 = &i2c6;
+ i2c7 = &i2c7;
+ i2c8 = &i2c8;
serial0 = &uart0;
serial1 = &uart1;
serial2 = &uart2;
status = "disabled";
};
+ sdhci: sdhci@fe330000 {
+ compatible = "rockchip,rk3399-sdhci-5.1", "arasan,sdhci-5.1";
+ reg = <0x0 0xfe330000 0x0 0x10000>;
+ interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
+ arasan,soc-ctl-syscon = <&grf>;
+ assigned-clocks = <&cru SCLK_EMMC>;
+ assigned-clock-rates = <200000000>;
+ clocks = <&cru SCLK_EMMC>, <&cru ACLK_EMMC>;
+ clock-names = "clk_xin", "clk_ahb";
+ clock-output-names = "emmc_cardclock";
+ #clock-cells = <0>;
+ phys = <&emmc_phy>;
+ phy-names = "phy_arasan";
+ status = "disabled";
+ };
+
usb_host0_ehci: usb@fe380000 {
compatible = "generic-ehci";
reg = <0x0 0xfe380000 0x0 0x20000>;
};
};
+ i2c1: i2c@ff110000 {
+ compatible = "rockchip,rk3399-i2c";
+ reg = <0x0 0xff110000 0x0 0x1000>;
+ assigned-clocks = <&cru SCLK_I2C1>;
+ assigned-clock-rates = <200000000>;
+ clocks = <&cru SCLK_I2C1>, <&cru PCLK_I2C1>;
+ clock-names = "i2c", "pclk";
+ interrupts = <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_xfer>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ i2c2: i2c@ff120000 {
+ compatible = "rockchip,rk3399-i2c";
+ reg = <0x0 0xff120000 0x0 0x1000>;
+ assigned-clocks = <&cru SCLK_I2C2>;
+ assigned-clock-rates = <200000000>;
+ clocks = <&cru SCLK_I2C2>, <&cru PCLK_I2C2>;
+ clock-names = "i2c", "pclk";
+ interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2_xfer>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ i2c3: i2c@ff130000 {
+ compatible = "rockchip,rk3399-i2c";
+ reg = <0x0 0xff130000 0x0 0x1000>;
+ assigned-clocks = <&cru SCLK_I2C3>;
+ assigned-clock-rates = <200000000>;
+ clocks = <&cru SCLK_I2C3>, <&cru PCLK_I2C3>;
+ clock-names = "i2c", "pclk";
+ interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c3_xfer>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ i2c5: i2c@ff140000 {
+ compatible = "rockchip,rk3399-i2c";
+ reg = <0x0 0xff140000 0x0 0x1000>;
+ assigned-clocks = <&cru SCLK_I2C5>;
+ assigned-clock-rates = <200000000>;
+ clocks = <&cru SCLK_I2C5>, <&cru PCLK_I2C5>;
+ clock-names = "i2c", "pclk";
+ interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c5_xfer>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ i2c6: i2c@ff150000 {
+ compatible = "rockchip,rk3399-i2c";
+ reg = <0x0 0xff150000 0x0 0x1000>;
+ assigned-clocks = <&cru SCLK_I2C6>;
+ assigned-clock-rates = <200000000>;
+ clocks = <&cru SCLK_I2C6>, <&cru PCLK_I2C6>;
+ clock-names = "i2c", "pclk";
+ interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c6_xfer>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ i2c7: i2c@ff160000 {
+ compatible = "rockchip,rk3399-i2c";
+ reg = <0x0 0xff160000 0x0 0x1000>;
+ assigned-clocks = <&cru SCLK_I2C7>;
+ assigned-clock-rates = <200000000>;
+ clocks = <&cru SCLK_I2C7>, <&cru PCLK_I2C7>;
+ clock-names = "i2c", "pclk";
+ interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c7_xfer>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
uart0: serial@ff180000 {
compatible = "rockchip,rk3399-uart", "snps,dw-apb-uart";
reg = <0x0 0xff180000 0x0 0x100>;
status = "disabled";
};
+ thermal-zones {
+ cpu_thermal: cpu {
+ polling-delay-passive = <100>;
+ polling-delay = <1000>;
+
+ thermal-sensors = <&tsadc 0>;
+
+ trips {
+ cpu_alert0: cpu_alert0 {
+ temperature = <70000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+ cpu_alert1: cpu_alert1 {
+ temperature = <75000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+ cpu_crit: cpu_crit {
+ temperature = <95000>;
+ hysteresis = <2000>;
+ type = "critical";
+ };
+ };
+
+ cooling-maps {
+ map0 {
+ trip = <&cpu_alert0>;
+ cooling-device =
+ <&cpu_b0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+ };
+ map1 {
+ trip = <&cpu_alert1>;
+ cooling-device =
+ <&cpu_l0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu_b0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+ };
+ };
+ };
+
+ gpu_thermal: gpu {
+ polling-delay-passive = <100>;
+ polling-delay = <1000>;
+
+ thermal-sensors = <&tsadc 1>;
+
+ trips {
+ gpu_alert0: gpu_alert0 {
+ temperature = <75000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+ gpu_crit: gpu_crit {
+ temperature = <95000>;
+ hysteresis = <2000>;
+ type = "critical";
+ };
+ };
+
+ cooling-maps {
+ map0 {
+ trip = <&gpu_alert0>;
+ cooling-device =
+ <&cpu_b0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+ };
+ };
+ };
+ };
+
+ tsadc: tsadc@ff260000 {
+ compatible = "rockchip,rk3399-tsadc";
+ reg = <0x0 0xff260000 0x0 0x100>;
+ interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
+ assigned-clocks = <&cru SCLK_TSADC>;
+ assigned-clock-rates = <750000>;
+ clocks = <&cru SCLK_TSADC>, <&cru PCLK_TSADC>;
+ clock-names = "tsadc", "apb_pclk";
+ resets = <&cru SRST_TSADC>;
+ reset-names = "tsadc-apb";
+ rockchip,grf = <&grf>;
+ rockchip,hw-tshut-temp = <95000>;
+ pinctrl-names = "init", "default", "sleep";
+ pinctrl-0 = <&otp_gpio>;
+ pinctrl-1 = <&otp_out>;
+ pinctrl-2 = <&otp_gpio>;
+ #thermal-sensor-cells = <1>;
+ status = "disabled";
+ };
+
pmugrf: syscon@ff320000 {
- compatible = "rockchip,rk3399-pmugrf", "syscon";
+ compatible = "rockchip,rk3399-pmugrf", "syscon", "simple-mfd";
reg = <0x0 0xff320000 0x0 0x1000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ pmu_io_domains: io-domains {
+ compatible = "rockchip,rk3399-pmu-io-voltage-domain";
+ status = "disabled";
+ };
};
spi3: spi@ff350000 {
status = "disabled";
};
+ i2c0: i2c@ff3c0000 {
+ compatible = "rockchip,rk3399-i2c";
+ reg = <0x0 0xff3c0000 0x0 0x1000>;
+ assigned-clocks = <&pmucru SCLK_I2C0_PMU>;
+ assigned-clock-rates = <200000000>;
+ clocks = <&pmucru SCLK_I2C0_PMU>, <&pmucru PCLK_I2C0_PMU>;
+ clock-names = "i2c", "pclk";
+ interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_xfer>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ i2c4: i2c@ff3d0000 {
+ compatible = "rockchip,rk3399-i2c";
+ reg = <0x0 0xff3d0000 0x0 0x1000>;
+ assigned-clocks = <&pmucru SCLK_I2C4_PMU>;
+ assigned-clock-rates = <200000000>;
+ clocks = <&pmucru SCLK_I2C4_PMU>, <&pmucru PCLK_I2C4_PMU>;
+ clock-names = "i2c", "pclk";
+ interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c4_xfer>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ i2c8: i2c@ff3e0000 {
+ compatible = "rockchip,rk3399-i2c";
+ reg = <0x0 0xff3e0000 0x0 0x1000>;
+ assigned-clocks = <&pmucru SCLK_I2C8_PMU>;
+ assigned-clock-rates = <200000000>;
+ clocks = <&pmucru SCLK_I2C8_PMU>, <&pmucru PCLK_I2C8_PMU>;
+ clock-names = "i2c", "pclk";
+ interrupts = <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c8_xfer>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
pwm0: pwm@ff420000 {
compatible = "rockchip,rk3399-pwm", "rockchip,rk3288-pwm";
reg = <0x0 0xff420000 0x0 0x10>;
reg = <0x0 0xff760000 0x0 0x1000>;
#clock-cells = <1>;
#reset-cells = <1>;
+ assigned-clocks =
+ <&cru PLL_GPLL>, <&cru PLL_CPLL>,
+ <&cru PLL_NPLL>,
+ <&cru ACLK_PERIHP>, <&cru HCLK_PERIHP>,
+ <&cru PCLK_PERIHP>,
+ <&cru ACLK_PERILP0>, <&cru HCLK_PERILP0>,
+ <&cru PCLK_PERILP0>,
+ <&cru HCLK_PERILP1>, <&cru PCLK_PERILP1>;
+ assigned-clock-rates =
+ <594000000>, <800000000>,
+ <1000000000>,
+ <150000000>, <75000000>,
+ <37500000>,
+ <100000000>, <100000000>,
+ <50000000>,
+ <100000000>, <50000000>;
};
grf: syscon@ff770000 {
- compatible = "rockchip,rk3399-grf", "syscon";
+ compatible = "rockchip,rk3399-grf", "syscon", "simple-mfd";
reg = <0x0 0xff770000 0x0 0x10000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ io_domains: io-domains {
+ compatible = "rockchip,rk3399-io-voltage-domain";
+ status = "disabled";
+ };
+
+ emmc_phy: phy@f780 {
+ compatible = "rockchip,rk3399-emmc-phy";
+ reg = <0xf780 0x24>;
+ clocks = <&sdhci>;
+ clock-names = "emmcclk";
+ #phy-cells = <0>;
+ status = "disabled";
+ };
};
watchdog@ff840000 {
};
};
+ sleep {
+ ap_pwroff: ap-pwroff {
+ rockchip,pins = <1 5 RK_FUNC_1 &pcfg_pull_none>;
+ };
+
+ ddrio_pwroff: ddrio-pwroff {
+ rockchip,pins = <0 1 RK_FUNC_1 &pcfg_pull_none>;
+ };
+ };
+
spdif {
spdif_bus: spdif-bus {
rockchip,pins =
};
};
+ tsadc {
+ otp_gpio: otp-gpio {
+ rockchip,pins = <1 6 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ otp_out: otp-out {
+ rockchip,pins = <1 6 RK_FUNC_1 &pcfg_pull_none>;
+ };
+ };
+
uart0 {
uart0_xfer: uart0-xfer {
rockchip,pins =
* OTHER DEALINGS IN THE SOFTWARE.
*/
+/memreserve/ 0x80000000 0x00000008; /* cpu-release-addr */
+
/ {
compatible = "socionext,ph1-ld20";
#address-cells = <2>;
compatible = "arm,cortex-a72", "arm,armv8";
reg = <0 0x000>;
enable-method = "spin-table";
- cpu-release-addr = <0 0x80000100>;
+ cpu-release-addr = <0 0x80000000>;
};
cpu1: cpu@1 {
compatible = "arm,cortex-a72", "arm,armv8";
reg = <0 0x001>;
enable-method = "spin-table";
- cpu-release-addr = <0 0x80000100>;
+ cpu-release-addr = <0 0x80000000>;
};
cpu2: cpu@100 {
compatible = "arm,cortex-a53", "arm,armv8";
reg = <0 0x100>;
enable-method = "spin-table";
- cpu-release-addr = <0 0x80000100>;
+ cpu-release-addr = <0 0x80000000>;
};
cpu3: cpu@101 {
compatible = "arm,cortex-a53", "arm,armv8";
reg = <0 0x101>;
enable-method = "spin-table";
- cpu-release-addr = <0 0x80000100>;
+ cpu-release-addr = <0 0x80000000>;
};
};
reg = <0x59801000 0x400>;
};
- pinctrl: pinctrl@5f801000 {
- compatible = "socionext,ph1-ld20-pinctrl", "syscon";
- reg = <0x5f801000 0xe00>;
+ soc-glue@5f800000 {
+ compatible = "simple-mfd", "syscon";
+ reg = <0x5f800000 0x2000>;
+
+ pinctrl: pinctrl {
+ compatible = "socionext,uniphier-ld20-pinctrl";
+ };
};
gic: interrupt-controller@5fe00000 {
projects / platform / kernel / linux-starfive.git / commitdiff