--- /dev/null
+// SPDX-License-Identifier: GPL-2.0-only
+// Copyright (c) 2019 Pengutronix, Oleksij Rempel <kernel@pengutronix.de>
+/*
+ * +----------------------+
+ * GMAC1----RGMII----|--MAC0 |
+ * \---MDIO1----|--REGs |----MDIO3----\
+ * | | | +------+
+ * | | +--| |
+ * | MAC1-|----RMII--M-----| PHY0 |-o P0
+ * | | | | +------+
+ * | | | +--| |
+ * | MAC2-|----RMII--------| PHY1 |-o P1
+ * | | | | +------+
+ * | | | +--| |
+ * | MAC3-|----RMII--------| PHY2 |-o P2
+ * | | | | +------+
+ * | | | +--| |
+ * | MAC4-|----RMII--------| PHY3 |-o P3
+ * | | | | +------+
+ * | | | +--| |
+ * | MAC5-|--+-RMII--M-----|-PHY4-|-o P4
+ * | | | | +------+
+ * +----------------------+ | \--CFG_SW_PHY_SWAP
+ * GMAC0---------------RMII--------------------/ \-CFG_SW_PHY_ADDR_SWAP
+ * \---MDIO0--NC
+ *
+ * GMAC0 and MAC5 are connected together and use same PHY. Depending on
+ * configuration it can be PHY4 (default) or PHY0. Only GMAC0 or MAC5 can be
+ * used at same time. If GMAC0 is used (default) then MAC5 should be disabled.
+ *
+ * CFG_SW_PHY_SWAP - swap connections of PHY0 and PHY4. If this bit is not set
+ * PHY4 is connected to GMAC0/MAC5 bundle and PHY0 is connected to MAC1. If this
+ * bit is set, PHY4 is connected to MAC1 and PHY0 is connected to GMAC0/MAC5
+ * bundle.
+ *
+ * CFG_SW_PHY_ADDR_SWAP - swap addresses of PHY0 and PHY4
+ *
+ * CFG_SW_PHY_SWAP and CFG_SW_PHY_ADDR_SWAP are part of SoC specific register
+ * set and not related to switch internal registers.
+ */
+
+#include <linux/bitfield.h>
+#include <linux/module.h>
+#include <linux/of_irq.h>
+#include <linux/of_mdio.h>
+#include <linux/regmap.h>
+#include <linux/reset.h>
+#include <net/dsa.h>
+
+#define AR9331_SW_NAME "ar9331_switch"
+#define AR9331_SW_PORTS 6
+
+/* dummy reg to change page */
+#define AR9331_SW_REG_PAGE 0x40000
+
+/* Global Interrupt */
+#define AR9331_SW_REG_GINT 0x10
+#define AR9331_SW_REG_GINT_MASK 0x14
+#define AR9331_SW_GINT_PHY_INT BIT(2)
+
+#define AR9331_SW_REG_FLOOD_MASK 0x2c
+#define AR9331_SW_FLOOD_MASK_BROAD_TO_CPU BIT(26)
+
+#define AR9331_SW_REG_GLOBAL_CTRL 0x30
+#define AR9331_SW_GLOBAL_CTRL_MFS_M GENMASK(13, 0)
+
+#define AR9331_SW_REG_MDIO_CTRL 0x98
+#define AR9331_SW_MDIO_CTRL_BUSY BIT(31)
+#define AR9331_SW_MDIO_CTRL_MASTER_EN BIT(30)
+#define AR9331_SW_MDIO_CTRL_CMD_READ BIT(27)
+#define AR9331_SW_MDIO_CTRL_PHY_ADDR_M GENMASK(25, 21)
+#define AR9331_SW_MDIO_CTRL_REG_ADDR_M GENMASK(20, 16)
+#define AR9331_SW_MDIO_CTRL_DATA_M GENMASK(16, 0)
+
+#define AR9331_SW_REG_PORT_STATUS(_port) (0x100 + (_port) * 0x100)
+
+/* FLOW_LINK_EN - enable mac flow control config auto-neg with phy.
+ * If not set, mac can be config by software.
+ */
+#define AR9331_SW_PORT_STATUS_FLOW_LINK_EN BIT(12)
+
+/* LINK_EN - If set, MAC is configured from PHY link status.
+ * If not set, MAC should be configured by software.
+ */
+#define AR9331_SW_PORT_STATUS_LINK_EN BIT(9)
+#define AR9331_SW_PORT_STATUS_DUPLEX_MODE BIT(6)
+#define AR9331_SW_PORT_STATUS_RX_FLOW_EN BIT(5)
+#define AR9331_SW_PORT_STATUS_TX_FLOW_EN BIT(4)
+#define AR9331_SW_PORT_STATUS_RXMAC BIT(3)
+#define AR9331_SW_PORT_STATUS_TXMAC BIT(2)
+#define AR9331_SW_PORT_STATUS_SPEED_M GENMASK(1, 0)
+#define AR9331_SW_PORT_STATUS_SPEED_1000 2
+#define AR9331_SW_PORT_STATUS_SPEED_100 1
+#define AR9331_SW_PORT_STATUS_SPEED_10 0
+
+#define AR9331_SW_PORT_STATUS_MAC_MASK \
+ (AR9331_SW_PORT_STATUS_TXMAC | AR9331_SW_PORT_STATUS_RXMAC)
+
+#define AR9331_SW_PORT_STATUS_LINK_MASK \
+ (AR9331_SW_PORT_STATUS_LINK_EN | AR9331_SW_PORT_STATUS_FLOW_LINK_EN | \
+ AR9331_SW_PORT_STATUS_DUPLEX_MODE | \
+ AR9331_SW_PORT_STATUS_RX_FLOW_EN | AR9331_SW_PORT_STATUS_TX_FLOW_EN | \
+ AR9331_SW_PORT_STATUS_SPEED_M)
+
+/* Phy bypass mode
+ * ------------------------------------------------------------------------
+ * Bit: | 0 | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 |10 |11 |12 |13 |14 |15 |
+ *
+ * real | start | OP | PhyAddr | Reg Addr | TA |
+ * atheros| start | OP | 2'b00 |PhyAdd[2:0]| Reg Addr[4:0] | TA |
+ *
+ *
+ * Bit: |16 |17 |18 |19 |20 |21 |22 |23 |24 |25 |26 |27 |28 |29 |30 |31 |
+ * real | Data |
+ * atheros| Data |
+ *
+ * ------------------------------------------------------------------------
+ * Page address mode
+ * ------------------------------------------------------------------------
+ * Bit: | 0 | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 |10 |11 |12 |13 |14 |15 |
+ * real | start | OP | PhyAddr | Reg Addr | TA |
+ * atheros| start | OP | 2'b11 | 8'b0 | TA |
+ *
+ * Bit: |16 |17 |18 |19 |20 |21 |22 |23 |24 |25 |26 |27 |28 |29 |30 |31 |
+ * real | Data |
+ * atheros| | Page [9:0] |
+ */
+/* In case of Page Address mode, Bit[18:9] of 32 bit register address should be
+ * written to bits[9:0] of mdio data register.
+ */
+#define AR9331_SW_ADDR_PAGE GENMASK(18, 9)
+
+/* ------------------------------------------------------------------------
+ * Normal register access mode
+ * ------------------------------------------------------------------------
+ * Bit: | 0 | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 |10 |11 |12 |13 |14 |15 |
+ * real | start | OP | PhyAddr | Reg Addr | TA |
+ * atheros| start | OP | 2'b10 | low_addr[7:0] | TA |
+ *
+ * Bit: |16 |17 |18 |19 |20 |21 |22 |23 |24 |25 |26 |27 |28 |29 |30 |31 |
+ * real | Data |
+ * atheros| Data |
+ * ------------------------------------------------------------------------
+ */
+#define AR9331_SW_LOW_ADDR_PHY GENMASK(8, 6)
+#define AR9331_SW_LOW_ADDR_REG GENMASK(5, 1)
+
+#define AR9331_SW_MDIO_PHY_MODE_M GENMASK(4, 3)
+#define AR9331_SW_MDIO_PHY_MODE_PAGE 3
+#define AR9331_SW_MDIO_PHY_MODE_REG 2
+#define AR9331_SW_MDIO_PHY_MODE_BYPASS 0
+#define AR9331_SW_MDIO_PHY_ADDR_M GENMASK(2, 0)
+
+/* Empirical determined values */
+#define AR9331_SW_MDIO_POLL_SLEEP_US 1
+#define AR9331_SW_MDIO_POLL_TIMEOUT_US 20
+
+struct ar9331_sw_priv {
+ struct device *dev;
+ struct dsa_switch ds;
+ struct dsa_switch_ops ops;
+ struct irq_domain *irqdomain;
+ struct mii_bus *mbus; /* mdio master */
+ struct mii_bus *sbus; /* mdio slave */
+ struct regmap *regmap;
+ struct reset_control *sw_reset;
+};
+
+/* Warning: switch reset will reset last AR9331_SW_MDIO_PHY_MODE_PAGE request
+ * If some kind of optimization is used, the request should be repeated.
+ */
+static int ar9331_sw_reset(struct ar9331_sw_priv *priv)
+{
+ int ret;
+
+ ret = reset_control_assert(priv->sw_reset);
+ if (ret)
+ goto error;
+
+ /* AR9331 doc do not provide any information about proper reset
+ * sequence. The AR8136 (the closes switch to the AR9331) doc says:
+ * reset duration should be greater than 10ms. So, let's use this value
+ * for now.
+ */
+ usleep_range(10000, 15000);
+ ret = reset_control_deassert(priv->sw_reset);
+ if (ret)
+ goto error;
+ /* There is no information on how long should we wait after reset.
+ * AR8136 has an EEPROM and there is an Interrupt for EEPROM load
+ * status. AR9331 has no EEPROM support.
+ * For now, do not wait. In case AR8136 will be needed, the after
+ * reset delay can be added as well.
+ */
+
+ return 0;
+error:
+ dev_err_ratelimited(priv->dev, "%s: %i\n", __func__, ret);
+ return ret;
+}
+
+static int ar9331_sw_mbus_write(struct mii_bus *mbus, int port, int regnum,
+ u16 data)
+{
+ struct ar9331_sw_priv *priv = mbus->priv;
+ struct regmap *regmap = priv->regmap;
+ u32 val;
+ int ret;
+
+ ret = regmap_write(regmap, AR9331_SW_REG_MDIO_CTRL,
+ AR9331_SW_MDIO_CTRL_BUSY |
+ AR9331_SW_MDIO_CTRL_MASTER_EN |
+ FIELD_PREP(AR9331_SW_MDIO_CTRL_PHY_ADDR_M, port) |
+ FIELD_PREP(AR9331_SW_MDIO_CTRL_REG_ADDR_M, regnum) |
+ FIELD_PREP(AR9331_SW_MDIO_CTRL_DATA_M, data));
+ if (ret)
+ goto error;
+
+ ret = regmap_read_poll_timeout(regmap, AR9331_SW_REG_MDIO_CTRL, val,
+ !(val & AR9331_SW_MDIO_CTRL_BUSY),
+ AR9331_SW_MDIO_POLL_SLEEP_US,
+ AR9331_SW_MDIO_POLL_TIMEOUT_US);
+ if (ret)
+ goto error;
+
+ return 0;
+error:
+ dev_err_ratelimited(priv->dev, "PHY write error: %i\n", ret);
+ return ret;
+}
+
+static int ar9331_sw_mbus_read(struct mii_bus *mbus, int port, int regnum)
+{
+ struct ar9331_sw_priv *priv = mbus->priv;
+ struct regmap *regmap = priv->regmap;
+ u32 val;
+ int ret;
+
+ ret = regmap_write(regmap, AR9331_SW_REG_MDIO_CTRL,
+ AR9331_SW_MDIO_CTRL_BUSY |
+ AR9331_SW_MDIO_CTRL_MASTER_EN |
+ AR9331_SW_MDIO_CTRL_CMD_READ |
+ FIELD_PREP(AR9331_SW_MDIO_CTRL_PHY_ADDR_M, port) |
+ FIELD_PREP(AR9331_SW_MDIO_CTRL_REG_ADDR_M, regnum));
+ if (ret)
+ goto error;
+
+ ret = regmap_read_poll_timeout(regmap, AR9331_SW_REG_MDIO_CTRL, val,
+ !(val & AR9331_SW_MDIO_CTRL_BUSY),
+ AR9331_SW_MDIO_POLL_SLEEP_US,
+ AR9331_SW_MDIO_POLL_TIMEOUT_US);
+ if (ret)
+ goto error;
+
+ ret = regmap_read(regmap, AR9331_SW_REG_MDIO_CTRL, &val);
+ if (ret)
+ goto error;
+
+ return FIELD_GET(AR9331_SW_MDIO_CTRL_DATA_M, val);
+
+error:
+ dev_err_ratelimited(priv->dev, "PHY read error: %i\n", ret);
+ return ret;
+}
+
+static int ar9331_sw_mbus_init(struct ar9331_sw_priv *priv)
+{
+ struct device *dev = priv->dev;
+ static struct mii_bus *mbus;
+ struct device_node *np, *mnp;
+ int ret;
+
+ np = dev->of_node;
+
+ mbus = devm_mdiobus_alloc(dev);
+ if (!mbus)
+ return -ENOMEM;
+
+ mbus->name = np->full_name;
+ snprintf(mbus->id, MII_BUS_ID_SIZE, "%pOF", np);
+
+ mbus->read = ar9331_sw_mbus_read;
+ mbus->write = ar9331_sw_mbus_write;
+ mbus->priv = priv;
+ mbus->parent = dev;
+
+ mnp = of_get_child_by_name(np, "mdio");
+ if (!mnp)
+ return -ENODEV;
+
+ ret = of_mdiobus_register(mbus, mnp);
+ of_node_put(mnp);
+ if (ret)
+ return ret;
+
+ priv->mbus = mbus;
+
+ return 0;
+}
+
+static int ar9331_sw_setup(struct dsa_switch *ds)
+{
+ struct ar9331_sw_priv *priv = (struct ar9331_sw_priv *)ds->priv;
+ struct regmap *regmap = priv->regmap;
+ int ret;
+
+ ret = ar9331_sw_reset(priv);
+ if (ret)
+ return ret;
+
+ /* Reset will set proper defaults. CPU - Port0 will be enabled and
+ * configured. All other ports (ports 1 - 5) are disabled
+ */
+ ret = ar9331_sw_mbus_init(priv);
+ if (ret)
+ return ret;
+
+ /* Do not drop broadcast frames */
+ ret = regmap_write_bits(regmap, AR9331_SW_REG_FLOOD_MASK,
+ AR9331_SW_FLOOD_MASK_BROAD_TO_CPU,
+ AR9331_SW_FLOOD_MASK_BROAD_TO_CPU);
+ if (ret)
+ goto error;
+
+ /* Set max frame size to the maximum supported value */
+ ret = regmap_write_bits(regmap, AR9331_SW_REG_GLOBAL_CTRL,
+ AR9331_SW_GLOBAL_CTRL_MFS_M,
+ AR9331_SW_GLOBAL_CTRL_MFS_M);
+ if (ret)
+ goto error;
+
+ return 0;
+error:
+ dev_err_ratelimited(priv->dev, "%s: %i\n", __func__, ret);
+ return ret;
+}
+
+static void ar9331_sw_port_disable(struct dsa_switch *ds, int port)
+{
+ struct ar9331_sw_priv *priv = (struct ar9331_sw_priv *)ds->priv;
+ struct regmap *regmap = priv->regmap;
+ int ret;
+
+ ret = regmap_write(regmap, AR9331_SW_REG_PORT_STATUS(port), 0);
+ if (ret)
+ dev_err_ratelimited(priv->dev, "%s: %i\n", __func__, ret);
+}
+
+static enum dsa_tag_protocol ar9331_sw_get_tag_protocol(struct dsa_switch *ds,
+ int port)
+{
+ return DSA_TAG_PROTO_AR9331;
+}
+
+static void ar9331_sw_phylink_validate(struct dsa_switch *ds, int port,
+ unsigned long *supported,
+ struct phylink_link_state *state)
+{
+ __ETHTOOL_DECLARE_LINK_MODE_MASK(mask) = { 0, };
+
+ switch (port) {
+ case 0:
+ if (state->interface != PHY_INTERFACE_MODE_GMII)
+ goto unsupported;
+
+ phylink_set(mask, 1000baseT_Full);
+ phylink_set(mask, 1000baseT_Half);
+ break;
+ case 1:
+ case 2:
+ case 3:
+ case 4:
+ case 5:
+ if (state->interface != PHY_INTERFACE_MODE_INTERNAL)
+ goto unsupported;
+ break;
+ default:
+ bitmap_zero(supported, __ETHTOOL_LINK_MODE_MASK_NBITS);
+ dev_err(ds->dev, "Unsupported port: %i\n", port);
+ return;
+ }
+
+ phylink_set_port_modes(mask);
+ phylink_set(mask, Pause);
+ phylink_set(mask, Asym_Pause);
+
+ phylink_set(mask, 10baseT_Half);
+ phylink_set(mask, 10baseT_Full);
+ phylink_set(mask, 100baseT_Half);
+ phylink_set(mask, 100baseT_Full);
+
+ bitmap_and(supported, supported, mask,
+ __ETHTOOL_LINK_MODE_MASK_NBITS);
+ bitmap_and(state->advertising, state->advertising, mask,
+ __ETHTOOL_LINK_MODE_MASK_NBITS);
+
+ return;
+
+unsupported:
+ bitmap_zero(supported, __ETHTOOL_LINK_MODE_MASK_NBITS);
+ dev_err(ds->dev, "Unsupported interface: %d, port: %d\n",
+ state->interface, port);
+}
+
+static void ar9331_sw_phylink_mac_config(struct dsa_switch *ds, int port,
+ unsigned int mode,
+ const struct phylink_link_state *state)
+{
+ struct ar9331_sw_priv *priv = (struct ar9331_sw_priv *)ds->priv;
+ struct regmap *regmap = priv->regmap;
+ int ret;
+ u32 val;
+
+ switch (state->speed) {
+ case SPEED_1000:
+ val = AR9331_SW_PORT_STATUS_SPEED_1000;
+ break;
+ case SPEED_100:
+ val = AR9331_SW_PORT_STATUS_SPEED_100;
+ break;
+ case SPEED_10:
+ val = AR9331_SW_PORT_STATUS_SPEED_10;
+ break;
+ default:
+ return;
+ }
+
+ if (state->duplex)
+ val |= AR9331_SW_PORT_STATUS_DUPLEX_MODE;
+
+ if (state->pause & MLO_PAUSE_TX)
+ val |= AR9331_SW_PORT_STATUS_TX_FLOW_EN;
+
+ if (state->pause & MLO_PAUSE_RX)
+ val |= AR9331_SW_PORT_STATUS_RX_FLOW_EN;
+
+ ret = regmap_update_bits(regmap, AR9331_SW_REG_PORT_STATUS(port),
+ AR9331_SW_PORT_STATUS_LINK_MASK, val);
+ if (ret)
+ dev_err_ratelimited(priv->dev, "%s: %i\n", __func__, ret);
+}
+
+static void ar9331_sw_phylink_mac_link_down(struct dsa_switch *ds, int port,
+ unsigned int mode,
+ phy_interface_t interface)
+{
+ struct ar9331_sw_priv *priv = (struct ar9331_sw_priv *)ds->priv;
+ struct regmap *regmap = priv->regmap;
+ int ret;
+
+ ret = regmap_update_bits(regmap, AR9331_SW_REG_PORT_STATUS(port),
+ AR9331_SW_PORT_STATUS_MAC_MASK, 0);
+ if (ret)
+ dev_err_ratelimited(priv->dev, "%s: %i\n", __func__, ret);
+}
+
+static void ar9331_sw_phylink_mac_link_up(struct dsa_switch *ds, int port,
+ unsigned int mode,
+ phy_interface_t interface,
+ struct phy_device *phydev)
+{
+ struct ar9331_sw_priv *priv = (struct ar9331_sw_priv *)ds->priv;
+ struct regmap *regmap = priv->regmap;
+ int ret;
+
+ ret = regmap_update_bits(regmap, AR9331_SW_REG_PORT_STATUS(port),
+ AR9331_SW_PORT_STATUS_MAC_MASK,
+ AR9331_SW_PORT_STATUS_MAC_MASK);
+ if (ret)
+ dev_err_ratelimited(priv->dev, "%s: %i\n", __func__, ret);
+}
+
+static const struct dsa_switch_ops ar9331_sw_ops = {
+ .get_tag_protocol = ar9331_sw_get_tag_protocol,
+ .setup = ar9331_sw_setup,
+ .port_disable = ar9331_sw_port_disable,
+ .phylink_validate = ar9331_sw_phylink_validate,
+ .phylink_mac_config = ar9331_sw_phylink_mac_config,
+ .phylink_mac_link_down = ar9331_sw_phylink_mac_link_down,
+ .phylink_mac_link_up = ar9331_sw_phylink_mac_link_up,
+};
+
+static irqreturn_t ar9331_sw_irq(int irq, void *data)
+{
+ struct ar9331_sw_priv *priv = data;
+ struct regmap *regmap = priv->regmap;
+ u32 stat;
+ int ret;
+
+ ret = regmap_read(regmap, AR9331_SW_REG_GINT, &stat);
+ if (ret) {
+ dev_err(priv->dev, "can't read interrupt status\n");
+ return IRQ_NONE;
+ }
+
+ if (!stat)
+ return IRQ_NONE;
+
+ if (stat & AR9331_SW_GINT_PHY_INT) {
+ int child_irq;
+
+ child_irq = irq_find_mapping(priv->irqdomain, 0);
+ handle_nested_irq(child_irq);
+ }
+
+ ret = regmap_write(regmap, AR9331_SW_REG_GINT, stat);
+ if (ret) {
+ dev_err(priv->dev, "can't write interrupt status\n");
+ return IRQ_NONE;
+ }
+
+ return IRQ_HANDLED;
+}
+
+static void ar9331_sw_mask_irq(struct irq_data *d)
+{
+ struct ar9331_sw_priv *priv = irq_data_get_irq_chip_data(d);
+ struct regmap *regmap = priv->regmap;
+ int ret;
+
+ ret = regmap_update_bits(regmap, AR9331_SW_REG_GINT_MASK,
+ AR9331_SW_GINT_PHY_INT, 0);
+ if (ret)
+ dev_err(priv->dev, "could not mask IRQ\n");
+}
+
+static void ar9331_sw_unmask_irq(struct irq_data *d)
+{
+ struct ar9331_sw_priv *priv = irq_data_get_irq_chip_data(d);
+ struct regmap *regmap = priv->regmap;
+ int ret;
+
+ ret = regmap_update_bits(regmap, AR9331_SW_REG_GINT_MASK,
+ AR9331_SW_GINT_PHY_INT,
+ AR9331_SW_GINT_PHY_INT);
+ if (ret)
+ dev_err(priv->dev, "could not unmask IRQ\n");
+}
+
+static struct irq_chip ar9331_sw_irq_chip = {
+ .name = AR9331_SW_NAME,
+ .irq_mask = ar9331_sw_mask_irq,
+ .irq_unmask = ar9331_sw_unmask_irq,
+};
+
+static int ar9331_sw_irq_map(struct irq_domain *domain, unsigned int irq,
+ irq_hw_number_t hwirq)
+{
+ irq_set_chip_data(irq, domain->host_data);
+ irq_set_chip_and_handler(irq, &ar9331_sw_irq_chip, handle_simple_irq);
+ irq_set_nested_thread(irq, 1);
+ irq_set_noprobe(irq);
+
+ return 0;
+}
+
+static void ar9331_sw_irq_unmap(struct irq_domain *d, unsigned int irq)
+{
+ irq_set_nested_thread(irq, 0);
+ irq_set_chip_and_handler(irq, NULL, NULL);
+ irq_set_chip_data(irq, NULL);
+}
+
+static const struct irq_domain_ops ar9331_sw_irqdomain_ops = {
+ .map = ar9331_sw_irq_map,
+ .unmap = ar9331_sw_irq_unmap,
+ .xlate = irq_domain_xlate_onecell,
+};
+
+static int ar9331_sw_irq_init(struct ar9331_sw_priv *priv)
+{
+ struct device_node *np = priv->dev->of_node;
+ struct device *dev = priv->dev;
+ int ret, irq;
+
+ irq = of_irq_get(np, 0);
+ if (irq <= 0) {
+ dev_err(dev, "failed to get parent IRQ\n");
+ return irq ? irq : -EINVAL;
+ }
+
+ ret = devm_request_threaded_irq(dev, irq, NULL, ar9331_sw_irq,
+ IRQF_ONESHOT, AR9331_SW_NAME, priv);
+ if (ret) {
+ dev_err(dev, "unable to request irq: %d\n", ret);
+ return ret;
+ }
+
+ priv->irqdomain = irq_domain_add_linear(np, 1, &ar9331_sw_irqdomain_ops,
+ priv);
+ if (!priv->irqdomain) {
+ dev_err(dev, "failed to create IRQ domain\n");
+ return -EINVAL;
+ }
+
+ irq_set_parent(irq_create_mapping(priv->irqdomain, 0), irq);
+
+ return 0;
+}
+
+static int __ar9331_mdio_write(struct mii_bus *sbus, u8 mode, u16 reg, u16 val)
+{
+ u8 r, p;
+
+ p = FIELD_PREP(AR9331_SW_MDIO_PHY_MODE_M, mode) |
+ FIELD_GET(AR9331_SW_LOW_ADDR_PHY, reg);
+ r = FIELD_GET(AR9331_SW_LOW_ADDR_REG, reg);
+
+ return mdiobus_write(sbus, p, r, val);
+}
+
+static int __ar9331_mdio_read(struct mii_bus *sbus, u16 reg)
+{
+ u8 r, p;
+
+ p = FIELD_PREP(AR9331_SW_MDIO_PHY_MODE_M, AR9331_SW_MDIO_PHY_MODE_REG) |
+ FIELD_GET(AR9331_SW_LOW_ADDR_PHY, reg);
+ r = FIELD_GET(AR9331_SW_LOW_ADDR_REG, reg);
+
+ return mdiobus_read(sbus, p, r);
+}
+
+static int ar9331_mdio_read(void *ctx, const void *reg_buf, size_t reg_len,
+ void *val_buf, size_t val_len)
+{
+ struct ar9331_sw_priv *priv = ctx;
+ struct mii_bus *sbus = priv->sbus;
+ u32 reg = *(u32 *)reg_buf;
+ int ret;
+
+ if (reg == AR9331_SW_REG_PAGE) {
+ /* We cannot read the page selector register from hardware and
+ * we cache its value in regmap. Return all bits set here,
+ * that regmap will always write the page on first use.
+ */
+ *(u32 *)val_buf = GENMASK(9, 0);
+ return 0;
+ }
+
+ ret = __ar9331_mdio_read(sbus, reg);
+ if (ret < 0)
+ goto error;
+
+ *(u32 *)val_buf = ret;
+ ret = __ar9331_mdio_read(sbus, reg + 2);
+ if (ret < 0)
+ goto error;
+
+ *(u32 *)val_buf |= ret << 16;
+
+ return 0;
+error:
+ dev_err_ratelimited(&sbus->dev, "Bus error. Failed to read register.\n");
+ return ret;
+}
+
+static int ar9331_mdio_write(void *ctx, u32 reg, u32 val)
+{
+ struct ar9331_sw_priv *priv = (struct ar9331_sw_priv *)ctx;
+ struct mii_bus *sbus = priv->sbus;
+ int ret;
+
+ if (reg == AR9331_SW_REG_PAGE) {
+ ret = __ar9331_mdio_write(sbus, AR9331_SW_MDIO_PHY_MODE_PAGE,
+ 0, val);
+ if (ret < 0)
+ goto error;
+
+ return 0;
+ }
+
+ ret = __ar9331_mdio_write(sbus, AR9331_SW_MDIO_PHY_MODE_REG, reg, val);
+ if (ret < 0)
+ goto error;
+
+ ret = __ar9331_mdio_write(sbus, AR9331_SW_MDIO_PHY_MODE_REG, reg + 2,
+ val >> 16);
+ if (ret < 0)
+ goto error;
+
+ return 0;
+error:
+ dev_err_ratelimited(&sbus->dev, "Bus error. Failed to write register.\n");
+ return ret;
+}
+
+static int ar9331_sw_bus_write(void *context, const void *data, size_t count)
+{
+ u32 reg = *(u32 *)data;
+ u32 val = *((u32 *)data + 1);
+
+ return ar9331_mdio_write(context, reg, val);
+}
+
+static const struct regmap_range ar9331_valid_regs[] = {
+ regmap_reg_range(0x0, 0x0),
+ regmap_reg_range(0x10, 0x14),
+ regmap_reg_range(0x20, 0x24),
+ regmap_reg_range(0x2c, 0x30),
+ regmap_reg_range(0x40, 0x44),
+ regmap_reg_range(0x50, 0x78),
+ regmap_reg_range(0x80, 0x98),
+
+ regmap_reg_range(0x100, 0x120),
+ regmap_reg_range(0x200, 0x220),
+ regmap_reg_range(0x300, 0x320),
+ regmap_reg_range(0x400, 0x420),
+ regmap_reg_range(0x500, 0x520),
+ regmap_reg_range(0x600, 0x620),
+
+ regmap_reg_range(0x20000, 0x200a4),
+ regmap_reg_range(0x20100, 0x201a4),
+ regmap_reg_range(0x20200, 0x202a4),
+ regmap_reg_range(0x20300, 0x203a4),
+ regmap_reg_range(0x20400, 0x204a4),
+ regmap_reg_range(0x20500, 0x205a4),
+
+ /* dummy page selector reg */
+ regmap_reg_range(AR9331_SW_REG_PAGE, AR9331_SW_REG_PAGE),
+};
+
+static const struct regmap_range ar9331_nonvolatile_regs[] = {
+ regmap_reg_range(AR9331_SW_REG_PAGE, AR9331_SW_REG_PAGE),
+};
+
+static const struct regmap_range_cfg ar9331_regmap_range[] = {
+ {
+ .selector_reg = AR9331_SW_REG_PAGE,
+ .selector_mask = GENMASK(9, 0),
+ .selector_shift = 0,
+
+ .window_start = 0,
+ .window_len = 512,
+
+ .range_min = 0,
+ .range_max = AR9331_SW_REG_PAGE - 4,
+ },
+};
+
+static const struct regmap_access_table ar9331_register_set = {
+ .yes_ranges = ar9331_valid_regs,
+ .n_yes_ranges = ARRAY_SIZE(ar9331_valid_regs),
+};
+
+static const struct regmap_access_table ar9331_volatile_set = {
+ .no_ranges = ar9331_nonvolatile_regs,
+ .n_no_ranges = ARRAY_SIZE(ar9331_nonvolatile_regs),
+};
+
+static const struct regmap_config ar9331_mdio_regmap_config = {
+ .reg_bits = 32,
+ .val_bits = 32,
+ .reg_stride = 4,
+ .max_register = AR9331_SW_REG_PAGE,
+
+ .ranges = ar9331_regmap_range,
+ .num_ranges = ARRAY_SIZE(ar9331_regmap_range),
+
+ .volatile_table = &ar9331_volatile_set,
+ .wr_table = &ar9331_register_set,
+ .rd_table = &ar9331_register_set,
+
+ .cache_type = REGCACHE_RBTREE,
+};
+
+static struct regmap_bus ar9331_sw_bus = {
+ .reg_format_endian_default = REGMAP_ENDIAN_NATIVE,
+ .val_format_endian_default = REGMAP_ENDIAN_NATIVE,
+ .read = ar9331_mdio_read,
+ .write = ar9331_sw_bus_write,
+ .max_raw_read = 4,
+ .max_raw_write = 4,
+};
+
+static int ar9331_sw_probe(struct mdio_device *mdiodev)
+{
+ struct ar9331_sw_priv *priv;
+ struct dsa_switch *ds;
+ int ret;
+
+ priv = devm_kzalloc(&mdiodev->dev, sizeof(*priv), GFP_KERNEL);
+ if (!priv)
+ return -ENOMEM;
+
+ priv->regmap = devm_regmap_init(&mdiodev->dev, &ar9331_sw_bus, priv,
+ &ar9331_mdio_regmap_config);
+ if (IS_ERR(priv->regmap)) {
+ ret = PTR_ERR(priv->regmap);
+ dev_err(&mdiodev->dev, "regmap init failed: %d\n", ret);
+ return ret;
+ }
+
+ priv->sw_reset = devm_reset_control_get(&mdiodev->dev, "switch");
+ if (IS_ERR(priv->sw_reset)) {
+ dev_err(&mdiodev->dev, "missing switch reset\n");
+ return PTR_ERR(priv->sw_reset);
+ }
+
+ priv->sbus = mdiodev->bus;
+ priv->dev = &mdiodev->dev;
+
+ ret = ar9331_sw_irq_init(priv);
+ if (ret)
+ return ret;
+
+ ds = &priv->ds;
+ ds->dev = &mdiodev->dev;
+ ds->num_ports = AR9331_SW_PORTS;
+ ds->priv = priv;
+ priv->ops = ar9331_sw_ops;
+ ds->ops = &priv->ops;
+ dev_set_drvdata(&mdiodev->dev, priv);
+
+ ret = dsa_register_switch(ds);
+ if (ret)
+ goto err_remove_irq;
+
+ return 0;
+
+err_remove_irq:
+ irq_domain_remove(priv->irqdomain);
+
+ return ret;
+}
+
+static void ar9331_sw_remove(struct mdio_device *mdiodev)
+{
+ struct ar9331_sw_priv *priv = dev_get_drvdata(&mdiodev->dev);
+
+ irq_domain_remove(priv->irqdomain);
+ mdiobus_unregister(priv->mbus);
+ dsa_unregister_switch(&priv->ds);
+
+ reset_control_assert(priv->sw_reset);
+}
+
+static const struct of_device_id ar9331_sw_of_match[] = {
+ { .compatible = "qca,ar9331-switch" },
+ { },
+};
+
+static struct mdio_driver ar9331_sw_mdio_driver = {
+ .probe = ar9331_sw_probe,
+ .remove = ar9331_sw_remove,
+ .mdiodrv.driver = {
+ .name = AR9331_SW_NAME,
+ .of_match_table = ar9331_sw_of_match,
+ },
+};
+
+mdio_module_driver(ar9331_sw_mdio_driver);
+
+MODULE_AUTHOR("Oleksij Rempel <kernel@pengutronix.de>");
+MODULE_DESCRIPTION("Driver for Atheros AR9331 switch");
+MODULE_LICENSE("GPL v2");
projects / platform / kernel / linux-starfive.git / commitdiff