imx6ul-liteboard.dtb \
imx6ul-phytec-segin-ff-rdk-nand.dtb \
imx6ul-pico-hobbit.dtb \
- imx6ul-pico-pi.dtb
+ imx6ul-pico-pi.dtb \
+ imx6ul-kontron-n631x-s.dtb \
+ imx6ull-kontron-n641x-s.dtb
dtb-$(CONFIG_MX6ULL) += \
imx6ull-14x14-evk.dtb \
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0 OR MIT
+/*
+ * Copyright (C) 2017 exceet electronics GmbH
+ * Copyright (C) 2018 Kontron Electronics GmbH
+ */
+
+#include "imx6ul-kontron-n6x1x-s-u-boot.dtsi"
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2017 exceet electronics GmbH
+ * Copyright (C) 2018 Kontron Electronics GmbH
+ * Copyright (c) 2019 Krzysztof Kozlowski <krzk@kernel.org>
+ */
+
+/dts-v1/;
+
+#include "imx6ul-kontron-n631x-som.dtsi"
+#include "imx6ul-kontron-n6x1x-s.dtsi"
+
+/ {
+ model = "Kontron N631X S";
+ compatible = "kontron,imx6ul-n631x-s", "kontron,imx6ul-n631x-som",
+ "fsl,imx6ul";
+};
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2017 exceet electronics GmbH
+ * Copyright (C) 2018 Kontron Electronics GmbH
+ * Copyright (c) 2019 Krzysztof Kozlowski <krzk@kernel.org>
+ */
+
+#include "imx6ul.dtsi"
+#include "imx6ul-kontron-n6x1x-som-common.dtsi"
+
+/ {
+ model = "Kontron N631X SOM";
+ compatible = "kontron,imx6ul-n631x-som", "fsl,imx6ul";
+};
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0 OR MIT
+/*
+ * Copyright (C) 2017 exceet electronics GmbH
+ * Copyright (C) 2018 Kontron Electronics GmbH
+ */
+
+#if defined(CONFIG_FIT)
+
+/ {
+ binman: binman {
+ filename = "flash.bin";
+ pad-byte = <0x00>;
+
+ spl: blob-ext@1 {
+ offset = <0x0>;
+ filename = "SPL";
+ };
+
+ uboot: blob-ext@2 {
+ offset = <0x11000>;
+ filename = "u-boot.img";
+ };
+ };
+};
+
+#endif /* CONFIG_FIT */
+
+/*
+ * To make the PHYs work, we need to set the reset pin once. Afterwards
+ * in Linux we can't assign the shared reset GPIO to the PHYs, as this
+ * would cause Linux to reset both PHYs every time one of them gets
+ * reinitialized.
+ *
+ * Also we disable the second ethernet as it currently doesn't work with
+ * the devicetree setup in U-Boot.
+ */
+
+&fec1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet1 &pinctrl_enet1_mdio>;
+ phy-mode = "rmii";
+ phy-handle = <ðphy1>;
+ phy-reset-gpios = <&gpio5 9 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethphy1: ethernet-phy@1 {
+ reg = <1>;
+ micrel,led-mode = <0>;
+ clocks = <&clks IMX6UL_CLK_ENET_REF>;
+ clock-names = "rmii-ref";
+ };
+ };
+};
+
+&fec2 {
+ status = "disabled";
+ /delete-property/ phy-handle;
+ /delete-node/ mdio;
+};
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2017 exceet electronics GmbH
+ * Copyright (C) 2018 Kontron Electronics GmbH
+ * Copyright (c) 2019 Krzysztof Kozlowski <krzk@kernel.org>
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include "imx6ul-kontron-n6x1x-som.dtsi"
+
+/ {
+ gpio-leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpio_leds>;
+
+ led1 {
+ label = "debug-led1";
+ gpios = <&gpio1 30 GPIO_ACTIVE_LOW>;
+ default-state = "off";
+ linux,default-trigger = "heartbeat";
+ };
+
+ led2 {
+ label = "debug-led2";
+ gpios = <&gpio5 3 GPIO_ACTIVE_LOW>;
+ default-state = "off";
+ };
+
+ led3 {
+ label = "debug-led3";
+ gpios = <&gpio5 2 GPIO_ACTIVE_LOW>;
+ default-state = "off";
+ };
+ };
+
+ pwm-beeper {
+ compatible = "pwm-beeper";
+ pwms = <&pwm8 0 5000>;
+ };
+
+ reg_3v3: regulator-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ reg_5v: regulator-5v {
+ compatible = "regulator-fixed";
+ regulator-name = "5v";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ };
+
+ reg_usb_otg1_vbus: regulator-usb-otg1-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usb_otg1_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio1 4 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ reg_vref_adc: regulator-vref-adc {
+ compatible = "regulator-fixed";
+ regulator-name = "vref-adc";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+};
+
+&adc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_adc1>;
+ num-channels = <3>;
+ vref-supply = <®_vref_adc>;
+ status = "okay";
+};
+
+&can2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flexcan2>;
+ status = "okay";
+};
+
+&ecspi1 {
+ cs-gpios = <&gpio4 26 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi1>;
+ status = "okay";
+
+ eeprom@0 {
+ compatible = "anvo,anv32e61w", "atmel,at25";
+ reg = <0>;
+ spi-max-frequency = <20000000>;
+ spi-cpha;
+ spi-cpol;
+ pagesize = <1>;
+ size = <8192>;
+ address-width = <16>;
+ };
+};
+
+&fec1 {
+ pinctrl-0 = <&pinctrl_enet1>;
+ /delete-node/ mdio;
+};
+
+&fec2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet2 &pinctrl_enet2_mdio>;
+ phy-mode = "rmii";
+ phy-handle = <ðphy2>;
+ status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethphy1: ethernet-phy@1 {
+ reg = <1>;
+ micrel,led-mode = <0>;
+ clocks = <&clks IMX6UL_CLK_ENET_REF>;
+ clock-names = "rmii-ref";
+ };
+
+ ethphy2: ethernet-phy@2 {
+ reg = <2>;
+ micrel,led-mode = <0>;
+ clocks = <&clks IMX6UL_CLK_ENET2_REF>;
+ clock-names = "rmii-ref";
+ };
+ };
+};
+
+&i2c1 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1>;
+ status = "okay";
+};
+
+&i2c4 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c4>;
+ status = "okay";
+
+ rtc@32 {
+ compatible = "epson,rx8900";
+ reg = <0x32>;
+ };
+};
+
+&pwm8 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm8>;
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1>;
+ status = "okay";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart2>;
+ linux,rs485-enabled-at-boot-time;
+ rs485-rx-during-tx;
+ rs485-rts-active-low;
+ uart-has-rtscts;
+ status = "okay";
+};
+
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart3>;
+ fsl,uart-has-rtscts;
+ status = "okay";
+};
+
+&uart4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart4>;
+ status = "okay";
+};
+
+&usbotg1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbotg1>;
+ dr_mode = "otg";
+ srp-disable;
+ hnp-disable;
+ adp-disable;
+ over-current-active-low;
+ vbus-supply = <®_usb_otg1_vbus>;
+ status = "okay";
+};
+
+&usbotg2 {
+ dr_mode = "host";
+ disable-over-current;
+ vbus-supply = <®_5v>;
+ status = "okay";
+};
+
+&usdhc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc1>;
+ cd-gpios = <&gpio1 19 GPIO_ACTIVE_LOW>;
+ keep-power-in-suspend;
+ wakeup-source;
+ vmmc-supply = <®_3v3>;
+ voltage-ranges = <3300 3300>;
+ bus-width = <4>;
+ no-1-8-v;
+ status = "okay";
+};
+
+&usdhc2 {
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc2>;
+ pinctrl-1 = <&pinctrl_usdhc2_100mhz>;
+ pinctrl-2 = <&pinctrl_usdhc2_200mhz>;
+ non-removable;
+ keep-power-in-suspend;
+ wakeup-source;
+ vmmc-supply = <®_3v3>;
+ voltage-ranges = <3300 3300>;
+ bus-width = <4>;
+ no-1-8-v;
+ status = "okay";
+};
+
+&wdog1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_wdog>;
+ fsl,ext-reset-output;
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl-0 = <&pinctrl_reset_out &pinctrl_gpio>;
+
+ pinctrl_adc1: adc1grp {
+ fsl,pins = <
+ MX6UL_PAD_GPIO1_IO02__GPIO1_IO02 0xb0
+ MX6UL_PAD_GPIO1_IO03__GPIO1_IO03 0xb0
+ MX6UL_PAD_GPIO1_IO08__GPIO1_IO08 0xb0
+ >;
+ };
+
+ pinctrl_ecspi1: ecspi1grp {
+ fsl,pins = <
+ MX6UL_PAD_CSI_DATA07__ECSPI1_MISO 0x100b1
+ MX6UL_PAD_CSI_DATA06__ECSPI1_MOSI 0x100b1
+ MX6UL_PAD_CSI_DATA04__ECSPI1_SCLK 0x100b1
+ MX6UL_PAD_CSI_DATA05__GPIO4_IO26 0x100b1 /* ECSPI1-CS1 */
+ >;
+ };
+
+ pinctrl_enet2: enet2grp {
+ fsl,pins = <
+ MX6UL_PAD_ENET2_RX_EN__ENET2_RX_EN 0x1b0b0
+ MX6UL_PAD_ENET2_RX_ER__ENET2_RX_ER 0x1b0b0
+ MX6UL_PAD_ENET2_RX_DATA0__ENET2_RDATA00 0x1b0b0
+ MX6UL_PAD_ENET2_RX_DATA1__ENET2_RDATA01 0x1b0b0
+ MX6UL_PAD_ENET2_TX_EN__ENET2_TX_EN 0x1b0b0
+ MX6UL_PAD_ENET2_TX_DATA0__ENET2_TDATA00 0x1b0b0
+ MX6UL_PAD_ENET2_TX_DATA1__ENET2_TDATA01 0x1b0b0
+ MX6UL_PAD_ENET2_TX_CLK__ENET2_REF_CLK2 0x4001b009
+ >;
+ };
+
+ pinctrl_enet2_mdio: enet2mdiogrp {
+ fsl,pins = <
+ MX6UL_PAD_GPIO1_IO07__ENET2_MDC 0x1b0b0
+ MX6UL_PAD_GPIO1_IO06__ENET2_MDIO 0x1b0b0
+ >;
+ };
+
+ pinctrl_flexcan2: flexcan2grp{
+ fsl,pins = <
+ MX6UL_PAD_UART2_RTS_B__FLEXCAN2_RX 0x1b020
+ MX6UL_PAD_UART2_CTS_B__FLEXCAN2_TX 0x1b020
+ >;
+ };
+
+ pinctrl_gpio: gpiogrp {
+ fsl,pins = <
+ MX6UL_PAD_SNVS_TAMPER5__GPIO5_IO05 0x1b0b0 /* DOUT1 */
+ MX6UL_PAD_SNVS_TAMPER4__GPIO5_IO04 0x1b0b0 /* DIN1 */
+ MX6UL_PAD_SNVS_TAMPER1__GPIO5_IO01 0x1b0b0 /* DOUT2 */
+ MX6UL_PAD_SNVS_TAMPER0__GPIO5_IO00 0x1b0b0 /* DIN2 */
+ >;
+ };
+
+ pinctrl_gpio_leds: gpioledsgrp {
+ fsl,pins = <
+ MX6UL_PAD_UART5_TX_DATA__GPIO1_IO30 0x1b0b0 /* LED H14 */
+ MX6UL_PAD_SNVS_TAMPER3__GPIO5_IO03 0x1b0b0 /* LED H15 */
+ MX6UL_PAD_SNVS_TAMPER2__GPIO5_IO02 0x1b0b0 /* LED H16 */
+ >;
+ };
+
+ pinctrl_i2c1: i2c1grp {
+ fsl,pins = <
+ MX6UL_PAD_CSI_PIXCLK__I2C1_SCL 0x4001b8b0
+ MX6UL_PAD_CSI_MCLK__I2C1_SDA 0x4001b8b0
+ >;
+ };
+
+ pinctrl_i2c4: i2c4grp {
+ fsl,pins = <
+ MX6UL_PAD_UART2_TX_DATA__I2C4_SCL 0x4001f8b0
+ MX6UL_PAD_UART2_RX_DATA__I2C4_SDA 0x4001f8b0
+ >;
+ };
+
+ pinctrl_pwm8: pwm8grp {
+ fsl,pins = <
+ MX6UL_PAD_CSI_HSYNC__PWM8_OUT 0x110b0
+ >;
+ };
+
+ pinctrl_uart1: uart1grp {
+ fsl,pins = <
+ MX6UL_PAD_UART1_TX_DATA__UART1_DCE_TX 0x1b0b1
+ MX6UL_PAD_UART1_RX_DATA__UART1_DCE_RX 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart2: uart2grp {
+ fsl,pins = <
+ MX6UL_PAD_NAND_DATA04__UART2_DCE_TX 0x1b0b1
+ MX6UL_PAD_NAND_DATA05__UART2_DCE_RX 0x1b0b1
+ MX6UL_PAD_NAND_DATA06__UART2_DCE_CTS 0x1b0b1
+ /*
+ * mux unused RTS to make sure it doesn't cause
+ * any interrupts when it is undefined
+ */
+ MX6UL_PAD_NAND_DATA07__UART2_DCE_RTS 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart3: uart3grp {
+ fsl,pins = <
+ MX6UL_PAD_UART3_TX_DATA__UART3_DCE_TX 0x1b0b1
+ MX6UL_PAD_UART3_RX_DATA__UART3_DCE_RX 0x1b0b1
+ MX6UL_PAD_UART3_CTS_B__UART3_DCE_CTS 0x1b0b1
+ MX6UL_PAD_UART3_RTS_B__UART3_DCE_RTS 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart4: uart4grp {
+ fsl,pins = <
+ MX6UL_PAD_UART4_TX_DATA__UART4_DCE_TX 0x1b0b1
+ MX6UL_PAD_UART4_RX_DATA__UART4_DCE_RX 0x1b0b1
+ >;
+ };
+
+ pinctrl_usbotg1: usbotg1 {
+ fsl,pins = <
+ MX6UL_PAD_GPIO1_IO04__GPIO1_IO04 0x1b0b0
+ >;
+ };
+
+ pinctrl_usdhc1: usdhc1grp {
+ fsl,pins = <
+ MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x17059
+ MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x10059
+ MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x17059
+ MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x17059
+ MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x17059
+ MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x17059
+ MX6UL_PAD_UART1_RTS_B__GPIO1_IO19 0x100b1 /* SD1_CD */
+ >;
+ };
+
+ pinctrl_usdhc2: usdhc2grp {
+ fsl,pins = <
+ MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x10059
+ MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x17059
+ MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x17059
+ MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x17059
+ MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x17059
+ MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x17059
+ >;
+ };
+
+ pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
+ fsl,pins = <
+ MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x100b9
+ MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x170b9
+ MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x170b9
+ MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x170b9
+ MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x170b9
+ MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x170b9
+ >;
+ };
+
+ pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
+ fsl,pins = <
+ MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x100f9
+ MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x170f9
+ MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x170f9
+ MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x170f9
+ MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x170f9
+ MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x170f9
+ >;
+ };
+
+ pinctrl_wdog: wdoggrp {
+ fsl,pins = <
+ MX6UL_PAD_GPIO1_IO09__WDOG1_WDOG_ANY 0x30b0
+ >;
+ };
+};
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2017 exceet electronics GmbH
+ * Copyright (C) 2018 Kontron Electronics GmbH
+ * Copyright (c) 2019 Krzysztof Kozlowski <krzk@kernel.org>
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+ gpio-leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpio_leds>;
+
+ led1 {
+ label = "debug-led1";
+ gpios = <&gpio1 30 GPIO_ACTIVE_LOW>;
+ default-state = "off";
+ linux,default-trigger = "heartbeat";
+ };
+
+ led2 {
+ label = "debug-led2";
+ gpios = <&gpio5 3 GPIO_ACTIVE_LOW>;
+ default-state = "off";
+ };
+
+ led3 {
+ label = "debug-led3";
+ gpios = <&gpio5 2 GPIO_ACTIVE_LOW>;
+ default-state = "off";
+ };
+ };
+
+ pwm-beeper {
+ compatible = "pwm-beeper";
+ pwms = <&pwm8 0 5000>;
+ };
+
+ reg_3v3: regulator-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ reg_5v: regulator-5v {
+ compatible = "regulator-fixed";
+ regulator-name = "5v";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ };
+
+ reg_usb_otg1_vbus: regulator-usb-otg1-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usb_otg1_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio1 4 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ reg_vref_adc: regulator-vref-adc {
+ compatible = "regulator-fixed";
+ regulator-name = "vref-adc";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+};
+
+&adc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_adc1>;
+ num-channels = <3>;
+ vref-supply = <®_vref_adc>;
+ status = "okay";
+};
+
+&can2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flexcan2>;
+ status = "okay";
+};
+
+&ecspi1 {
+ cs-gpios = <&gpio4 26 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi1>;
+ status = "okay";
+
+ eeprom@0 {
+ compatible = "anvo,anv32e61w", "atmel,at25";
+ reg = <0>;
+ spi-max-frequency = <20000000>;
+ spi-cpha;
+ spi-cpol;
+ pagesize = <1>;
+ size = <8192>;
+ address-width = <16>;
+ };
+};
+
+&fec1 {
+ pinctrl-0 = <&pinctrl_enet1>;
+ /delete-node/ mdio;
+};
+
+&fec2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet2 &pinctrl_enet2_mdio>;
+ phy-mode = "rmii";
+ phy-handle = <ðphy2>;
+ status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethphy1: ethernet-phy@1 {
+ reg = <1>;
+ micrel,led-mode = <0>;
+ clocks = <&clks IMX6UL_CLK_ENET_REF>;
+ clock-names = "rmii-ref";
+ };
+
+ ethphy2: ethernet-phy@2 {
+ reg = <2>;
+ micrel,led-mode = <0>;
+ clocks = <&clks IMX6UL_CLK_ENET2_REF>;
+ clock-names = "rmii-ref";
+ };
+ };
+};
+
+&i2c1 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1>;
+ status = "okay";
+};
+
+&i2c4 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c4>;
+ status = "okay";
+
+ rtc@32 {
+ compatible = "epson,rx8900";
+ reg = <0x32>;
+ };
+};
+
+&pwm8 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm8>;
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1>;
+ status = "okay";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart2>;
+ linux,rs485-enabled-at-boot-time;
+ rs485-rx-during-tx;
+ rs485-rts-active-low;
+ uart-has-rtscts;
+ status = "okay";
+};
+
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart3>;
+ fsl,uart-has-rtscts;
+ status = "okay";
+};
+
+&uart4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart4>;
+ status = "okay";
+};
+
+&usbotg1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbotg1>;
+ dr_mode = "otg";
+ srp-disable;
+ hnp-disable;
+ adp-disable;
+ over-current-active-low;
+ vbus-supply = <®_usb_otg1_vbus>;
+ status = "okay";
+};
+
+&usbotg2 {
+ dr_mode = "host";
+ disable-over-current;
+ vbus-supply = <®_5v>;
+ status = "okay";
+};
+
+&usdhc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc1>;
+ cd-gpios = <&gpio1 19 GPIO_ACTIVE_LOW>;
+ keep-power-in-suspend;
+ wakeup-source;
+ vmmc-supply = <®_3v3>;
+ voltage-ranges = <3300 3300>;
+ bus-width = <4>;
+ no-1-8-v;
+ status = "okay";
+};
+
+&usdhc2 {
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc2>;
+ pinctrl-1 = <&pinctrl_usdhc2_100mhz>;
+ pinctrl-2 = <&pinctrl_usdhc2_200mhz>;
+ non-removable;
+ keep-power-in-suspend;
+ wakeup-source;
+ vmmc-supply = <®_3v3>;
+ voltage-ranges = <3300 3300>;
+ bus-width = <4>;
+ no-1-8-v;
+ status = "okay";
+};
+
+&wdog1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_wdog>;
+ fsl,ext-reset-output;
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl-0 = <&pinctrl_reset_out &pinctrl_gpio>;
+
+ pinctrl_adc1: adc1grp {
+ fsl,pins = <
+ MX6UL_PAD_GPIO1_IO02__GPIO1_IO02 0xb0
+ MX6UL_PAD_GPIO1_IO03__GPIO1_IO03 0xb0
+ MX6UL_PAD_GPIO1_IO08__GPIO1_IO08 0xb0
+ >;
+ };
+
+ pinctrl_ecspi1: ecspi1grp {
+ fsl,pins = <
+ MX6UL_PAD_CSI_DATA07__ECSPI1_MISO 0x100b1
+ MX6UL_PAD_CSI_DATA06__ECSPI1_MOSI 0x100b1
+ MX6UL_PAD_CSI_DATA04__ECSPI1_SCLK 0x100b1
+ MX6UL_PAD_CSI_DATA05__GPIO4_IO26 0x100b1 /* ECSPI1-CS1 */
+ >;
+ };
+
+ pinctrl_enet2: enet2grp {
+ fsl,pins = <
+ MX6UL_PAD_ENET2_RX_EN__ENET2_RX_EN 0x1b0b0
+ MX6UL_PAD_ENET2_RX_ER__ENET2_RX_ER 0x1b0b0
+ MX6UL_PAD_ENET2_RX_DATA0__ENET2_RDATA00 0x1b0b0
+ MX6UL_PAD_ENET2_RX_DATA1__ENET2_RDATA01 0x1b0b0
+ MX6UL_PAD_ENET2_TX_EN__ENET2_TX_EN 0x1b0b0
+ MX6UL_PAD_ENET2_TX_DATA0__ENET2_TDATA00 0x1b0b0
+ MX6UL_PAD_ENET2_TX_DATA1__ENET2_TDATA01 0x1b0b0
+ MX6UL_PAD_ENET2_TX_CLK__ENET2_REF_CLK2 0x4001b009
+ >;
+ };
+
+ pinctrl_enet2_mdio: enet2mdiogrp {
+ fsl,pins = <
+ MX6UL_PAD_GPIO1_IO07__ENET2_MDC 0x1b0b0
+ MX6UL_PAD_GPIO1_IO06__ENET2_MDIO 0x1b0b0
+ >;
+ };
+
+ pinctrl_flexcan2: flexcan2grp{
+ fsl,pins = <
+ MX6UL_PAD_UART2_RTS_B__FLEXCAN2_RX 0x1b020
+ MX6UL_PAD_UART2_CTS_B__FLEXCAN2_TX 0x1b020
+ >;
+ };
+
+ pinctrl_gpio: gpiogrp {
+ fsl,pins = <
+ MX6UL_PAD_SNVS_TAMPER5__GPIO5_IO05 0x1b0b0 /* DOUT1 */
+ MX6UL_PAD_SNVS_TAMPER4__GPIO5_IO04 0x1b0b0 /* DIN1 */
+ MX6UL_PAD_SNVS_TAMPER1__GPIO5_IO01 0x1b0b0 /* DOUT2 */
+ MX6UL_PAD_SNVS_TAMPER0__GPIO5_IO00 0x1b0b0 /* DIN2 */
+ >;
+ };
+
+ pinctrl_gpio_leds: gpioledsgrp {
+ fsl,pins = <
+ MX6UL_PAD_UART5_TX_DATA__GPIO1_IO30 0x1b0b0 /* LED H14 */
+ MX6UL_PAD_SNVS_TAMPER3__GPIO5_IO03 0x1b0b0 /* LED H15 */
+ MX6UL_PAD_SNVS_TAMPER2__GPIO5_IO02 0x1b0b0 /* LED H16 */
+ >;
+ };
+
+ pinctrl_i2c1: i2c1grp {
+ fsl,pins = <
+ MX6UL_PAD_CSI_PIXCLK__I2C1_SCL 0x4001b8b0
+ MX6UL_PAD_CSI_MCLK__I2C1_SDA 0x4001b8b0
+ >;
+ };
+
+ pinctrl_i2c4: i2c4grp {
+ fsl,pins = <
+ MX6UL_PAD_UART2_TX_DATA__I2C4_SCL 0x4001f8b0
+ MX6UL_PAD_UART2_RX_DATA__I2C4_SDA 0x4001f8b0
+ >;
+ };
+
+ pinctrl_pwm8: pwm8grp {
+ fsl,pins = <
+ MX6UL_PAD_CSI_HSYNC__PWM8_OUT 0x110b0
+ >;
+ };
+
+ pinctrl_uart1: uart1grp {
+ fsl,pins = <
+ MX6UL_PAD_UART1_TX_DATA__UART1_DCE_TX 0x1b0b1
+ MX6UL_PAD_UART1_RX_DATA__UART1_DCE_RX 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart2: uart2grp {
+ fsl,pins = <
+ MX6UL_PAD_NAND_DATA04__UART2_DCE_TX 0x1b0b1
+ MX6UL_PAD_NAND_DATA05__UART2_DCE_RX 0x1b0b1
+ MX6UL_PAD_NAND_DATA06__UART2_DCE_CTS 0x1b0b1
+ /*
+ * mux unused RTS to make sure it doesn't cause
+ * any interrupts when it is undefined
+ */
+ MX6UL_PAD_NAND_DATA07__UART2_DCE_RTS 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart3: uart3grp {
+ fsl,pins = <
+ MX6UL_PAD_UART3_TX_DATA__UART3_DCE_TX 0x1b0b1
+ MX6UL_PAD_UART3_RX_DATA__UART3_DCE_RX 0x1b0b1
+ MX6UL_PAD_UART3_CTS_B__UART3_DCE_CTS 0x1b0b1
+ MX6UL_PAD_UART3_RTS_B__UART3_DCE_RTS 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart4: uart4grp {
+ fsl,pins = <
+ MX6UL_PAD_UART4_TX_DATA__UART4_DCE_TX 0x1b0b1
+ MX6UL_PAD_UART4_RX_DATA__UART4_DCE_RX 0x1b0b1
+ >;
+ };
+
+ pinctrl_usbotg1: usbotg1 {
+ fsl,pins = <
+ MX6UL_PAD_GPIO1_IO04__GPIO1_IO04 0x1b0b0
+ >;
+ };
+
+ pinctrl_usdhc1: usdhc1grp {
+ fsl,pins = <
+ MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x17059
+ MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x10059
+ MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x17059
+ MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x17059
+ MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x17059
+ MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x17059
+ MX6UL_PAD_UART1_RTS_B__GPIO1_IO19 0x100b1 /* SD1_CD */
+ >;
+ };
+
+ pinctrl_usdhc2: usdhc2grp {
+ fsl,pins = <
+ MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x10059
+ MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x17059
+ MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x17059
+ MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x17059
+ MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x17059
+ MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x17059
+ >;
+ };
+
+ pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
+ fsl,pins = <
+ MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x100b9
+ MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x170b9
+ MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x170b9
+ MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x170b9
+ MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x170b9
+ MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x170b9
+ >;
+ };
+
+ pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
+ fsl,pins = <
+ MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x100f9
+ MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x170f9
+ MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x170f9
+ MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x170f9
+ MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x170f9
+ MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x170f9
+ >;
+ };
+
+ pinctrl_wdog: wdoggrp {
+ fsl,pins = <
+ MX6UL_PAD_GPIO1_IO09__WDOG1_WDOG_ANY 0x30b0
+ >;
+ };
+};
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2017 exceet electronics GmbH
+ * Copyright (C) 2018 Kontron Electronics GmbH
+ * Copyright (c) 2019 Krzysztof Kozlowski <krzk@kernel.org>
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+ chosen {
+ stdout-path = &uart4;
+ };
+
+ memory@80000000 {
+ reg = <0x80000000 0x10000000>;
+ device_type = "memory";
+ };
+};
+
+&ecspi2 {
+ cs-gpios = <&gpio4 22 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi2>;
+ status = "okay";
+
+ spi-flash@0 {
+ compatible = "mxicy,mx25v8035f", "jedec,spi-nor";
+ spi-max-frequency = <50000000>;
+ reg = <0>;
+ };
+};
+
+&fec1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet1 &pinctrl_enet1_mdio>;
+ phy-mode = "rmii";
+ phy-handle = <ðphy1>;
+ status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethphy1: ethernet-phy@1 {
+ reg = <1>;
+ micrel,led-mode = <0>;
+ clocks = <&clks IMX6UL_CLK_ENET_REF>;
+ clock-names = "rmii-ref";
+ };
+ };
+};
+
+&fec2 {
+ phy-mode = "rmii";
+ status = "disabled";
+};
+
+&qspi {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_qspi>;
+ status = "okay";
+
+ spi-flash@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "spi-nand";
+ spi-max-frequency = <104000000>;
+ spi-tx-bus-width = <4>;
+ spi-rx-bus-width = <4>;
+ reg = <0>;
+ };
+};
+
+&iomuxc {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_reset_out>;
+
+ pinctrl_ecspi2: ecspi2grp {
+ fsl,pins = <
+ MX6UL_PAD_CSI_DATA03__ECSPI2_MISO 0x100b1
+ MX6UL_PAD_CSI_DATA02__ECSPI2_MOSI 0x100b1
+ MX6UL_PAD_CSI_DATA00__ECSPI2_SCLK 0x100b1
+ MX6UL_PAD_CSI_DATA01__GPIO4_IO22 0x100b1
+ >;
+ };
+
+ pinctrl_enet1: enet1grp {
+ fsl,pins = <
+ MX6UL_PAD_ENET1_RX_EN__ENET1_RX_EN 0x1b0b0
+ MX6UL_PAD_ENET1_RX_ER__ENET1_RX_ER 0x1b0b0
+ MX6UL_PAD_ENET1_RX_DATA0__ENET1_RDATA00 0x1b0b0
+ MX6UL_PAD_ENET1_RX_DATA1__ENET1_RDATA01 0x1b0b0
+ MX6UL_PAD_ENET1_TX_EN__ENET1_TX_EN 0x1b0b0
+ MX6UL_PAD_ENET1_TX_DATA0__ENET1_TDATA00 0x1b0b0
+ MX6UL_PAD_ENET1_TX_DATA1__ENET1_TDATA01 0x1b0b0
+ MX6UL_PAD_ENET1_TX_CLK__ENET1_REF_CLK1 0x4001b009
+ >;
+ };
+
+ pinctrl_enet1_mdio: enet1mdiogrp {
+ fsl,pins = <
+ MX6UL_PAD_GPIO1_IO07__ENET1_MDC 0x1b0b0
+ MX6UL_PAD_GPIO1_IO06__ENET1_MDIO 0x1b0b0
+ >;
+ };
+
+ pinctrl_qspi: qspigrp {
+ fsl,pins = <
+ MX6UL_PAD_NAND_WP_B__QSPI_A_SCLK 0x70a1
+ MX6UL_PAD_NAND_READY_B__QSPI_A_DATA00 0x70a1
+ MX6UL_PAD_NAND_CE0_B__QSPI_A_DATA01 0x70a1
+ MX6UL_PAD_NAND_CE1_B__QSPI_A_DATA02 0x70a1
+ MX6UL_PAD_NAND_CLE__QSPI_A_DATA03 0x70a1
+ MX6UL_PAD_NAND_DQS__QSPI_A_SS0_B 0x70a1
+ >;
+ };
+
+ pinctrl_reset_out: rstoutgrp {
+ fsl,pins = <
+ MX6UL_PAD_SNVS_TAMPER9__GPIO5_IO09 0x1b0b0
+ >;
+ };
+};
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0 OR MIT
+/*
+ * Copyright (C) 2017 exceet electronics GmbH
+ * Copyright (C) 2018 Kontron Electronics GmbH
+ */
+
+#include "imx6ul-kontron-n6x1x-s-u-boot.dtsi"
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2017 exceet electronics GmbH
+ * Copyright (C) 2019 Kontron Electronics GmbH
+ */
+
+/dts-v1/;
+
+#include "imx6ull-kontron-n641x-som.dtsi"
+#include "imx6ul-kontron-n6x1x-s.dtsi"
+
+/ {
+ model = "Kontron N641X S";
+ compatible = "kontron,imx6ull-n641x-s", "kontron,imx6ull-n641x-som",
+ "fsl,imx6ull";
+};
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2017 exceet electronics GmbH
+ * Copyright (C) 2018 Kontron Electronics GmbH
+ */
+
+#include "imx6ull.dtsi"
+#include "imx6ul-kontron-n6x1x-som-common.dtsi"
+
+/ {
+ model = "Kontron N641X SOM";
+ compatible = "kontron,imx6ull-n641x-som", "fsl,imx6ull";
+};
imply CMD_SATA
imply CMD_SPL
+config TARGET_KONTRON_MX6UL
+ bool "Kontron Electronics SL/BL i.MX6UL/ULL (N63xx/N64xx)"
+ depends on MX6UL
+ select BINMAN
+ select DM
+ select DM_THERMAL
+ select SUPPORT_SPL
+ imply CMD_DM
+
config TARGET_KOSAGI_NOVENA
bool "Kosagi Novena"
select BOARD_LATE_INIT
source "board/phytec/pcm058/Kconfig"
source "board/phytec/pcl063/Kconfig"
source "board/gateworks/gw_ventana/Kconfig"
+source "board/kontron/sl-mx6ul/Kconfig"
source "board/kosagi/novena/Kconfig"
source "board/softing/vining_2000/Kconfig"
source "board/liebherr/display5/Kconfig"
--- /dev/null
+if TARGET_KONTRON_MX6UL
+
+config SYS_BOARD
+ string
+ default "sl-mx6ul"
+
+config SYS_VENDOR
+ string
+ default "kontron"
+
+config SYS_CONFIG_NAME
+ string
+ default "kontron-sl-mx6ul"
+
+endif
--- /dev/null
+Kontron SL/BL i.MX6UL/ULL Boards (N63xx/N64xx)
+M: Frieder Schrempf <frieder.schrempf@kontron.de>
+S: Maintained
+F: arch/arm/dts/imx6ul-kontron-n6*
+F: arch/arm/dts/imx6ull-kontron-n6*
+F: board/kontron/sl-mx6ul
+F: configs/kontron-sl-mx6ul_defconfig
+F: doc/board/kontron/sl-mx6ul.rst
+F: include/configs/kontron-sl-mx6ul.h
--- /dev/null
+# SPDX-License-Identifier: GPL-2.0+
+# (C) Copyright 2018 Kontron Electronics GmbH
+
+ifdef CONFIG_SPL_BUILD
+obj-y := spl.o
+else
+obj-y := sl-mx6ul.o
+endif
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2018 Kontron Electronics GmbH
+ */
+
+#include <asm/arch/clock.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/global_data.h>
+#include <fdt_support.h>
+#include <phy.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int dram_init(void)
+{
+ gd->ram_size = imx_ddr_size();
+
+ return 0;
+}
+
+int ft_board_setup(void *blob, struct bd_info *bd)
+{
+ /*
+ * Overwrite the memory size in the devicetree that is
+ * passed to the kernel with the actual size detected.
+ */
+ return fdt_fixup_memory(blob, PHYS_SDRAM, gd->ram_size);
+}
+
+static int setup_fec(void)
+{
+ struct iomuxc *const iomuxc_regs = (struct iomuxc *)IOMUXC_BASE_ADDR;
+ int ret;
+
+ /*
+ * Use 50M anatop loopback REF_CLK1 for ENET1,
+ * clear gpr1[13], set gpr1[17].
+ */
+ clrsetbits_le32(&iomuxc_regs->gpr[1], IOMUX_GPR1_FEC1_MASK,
+ IOMUX_GPR1_FEC1_CLOCK_MUX1_SEL_MASK);
+
+ /*
+ * Use 50M anatop loopback REF_CLK2 for ENET2,
+ * clear gpr1[14], set gpr1[18].
+ */
+ clrsetbits_le32(&iomuxc_regs->gpr[1], IOMUX_GPR1_FEC2_MASK,
+ IOMUX_GPR1_FEC2_CLOCK_MUX1_SEL_MASK);
+
+ ret = enable_fec_anatop_clock(0, ENET_50MHZ);
+ if (ret)
+ return ret;
+
+ ret = enable_fec_anatop_clock(1, ENET_50MHZ);
+ if (ret)
+ return ret;
+
+ return 0;
+}
+
+int board_phy_config(struct phy_device *phydev)
+{
+ phy_write(phydev, MDIO_DEVAD_NONE, 0x1f, 0x8190);
+
+ if (phydev->drv->config)
+ phydev->drv->config(phydev);
+
+ return 0;
+}
+
+int board_early_init_f(void)
+{
+ enable_qspi_clk(0);
+
+ return 0;
+}
+
+int board_init(void)
+{
+ /* Address of boot parameters */
+ gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
+
+ setup_fec();
+
+ return 0;
+}
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2018 Kontron Electronics GmbH
+ */
+
+#include <asm/arch/clock.h>
+#include <asm/arch/crm_regs.h>
+#include <asm/arch/mx6-pins.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/global_data.h>
+#include <asm/gpio.h>
+#include <asm/io.h>
+#include <asm/mach-imx/iomux-v3.h>
+#include <fsl_esdhc_imx.h>
+#include <init.h>
+#include <linux/delay.h>
+#include <linux/sizes.h>
+#include <linux/errno.h>
+#include <mmc.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+enum {
+ BOARD_TYPE_KTN_N631X = 1,
+ BOARD_TYPE_KTN_N641X,
+ BOARD_TYPE_MAX
+};
+
+#define UART_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
+ PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
+ PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS)
+
+#define USDHC_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
+ PAD_CTL_PUS_22K_UP | PAD_CTL_SPEED_LOW | \
+ PAD_CTL_DSE_80ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS)
+
+#define USDHC_CD_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
+ PAD_CTL_PUS_100K_DOWN | PAD_CTL_SPEED_LOW | \
+ PAD_CTL_DSE_80ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS)
+
+#define SPI_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_SPEED_MED | \
+ PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST)
+
+#include <spl.h>
+#include <asm/arch/mx6-ddr.h>
+
+static iomux_v3_cfg_t const usdhc1_pads[] = {
+ MX6_PAD_SD1_CLK__USDHC1_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD1_CMD__USDHC1_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD1_DATA0__USDHC1_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD1_DATA1__USDHC1_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD1_DATA2__USDHC1_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD1_DATA3__USDHC1_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+
+ /* CD */
+ MX6_PAD_UART1_RTS_B__GPIO1_IO19 | MUX_PAD_CTRL(USDHC_CD_PAD_CTRL),
+};
+
+#define USDHC1_CD_GPIO IMX_GPIO_NR(1, 19)
+
+static iomux_v3_cfg_t const usdhc2_pads[] = {
+ MX6_PAD_NAND_RE_B__USDHC2_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_NAND_WE_B__USDHC2_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_NAND_DATA00__USDHC2_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_NAND_DATA01__USDHC2_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_NAND_DATA02__USDHC2_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_NAND_DATA03__USDHC2_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ /* RST */
+ MX6_PAD_NAND_ALE__GPIO4_IO10 | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+#define USDHC2_PWR_GPIO IMX_GPIO_NR(4, 10)
+
+static struct fsl_esdhc_cfg usdhc_cfg[2] = {
+ {USDHC1_BASE_ADDR, 0, 4},
+ {USDHC2_BASE_ADDR, 0, 4},
+};
+
+int board_mmc_getcd(struct mmc *mmc)
+{
+ struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
+ int ret = 0;
+
+ switch (cfg->esdhc_base) {
+ case USDHC1_BASE_ADDR:
+ ret = !gpio_get_value(USDHC1_CD_GPIO);
+ break;
+ case USDHC2_BASE_ADDR:
+ // This SDHC interface does not use a CD pin
+ ret = 1;
+ break;
+ }
+
+ return ret;
+}
+
+int board_mmc_init(struct bd_info *bis)
+{
+ int i, ret;
+
+ /*
+ * According to the board_mmc_init() the following map is done:
+ * (U-boot device node) (Physical Port)
+ * mmc0 USDHC1
+ * mmc1 USDHC2
+ */
+ for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) {
+ switch (i) {
+ case 0:
+ imx_iomux_v3_setup_multiple_pads(usdhc1_pads, ARRAY_SIZE(usdhc1_pads));
+ gpio_direction_input(USDHC1_CD_GPIO);
+ usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK);
+ break;
+ case 1:
+ imx_iomux_v3_setup_multiple_pads(usdhc2_pads, ARRAY_SIZE(usdhc2_pads));
+ gpio_direction_output(USDHC2_PWR_GPIO, 0);
+ udelay(500);
+ gpio_direction_output(USDHC2_PWR_GPIO, 1);
+ usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
+ break;
+ default:
+ printf("Warning: you configured more USDHC controllers (%d) than supported by the board\n",
+ i + 1);
+ return -EINVAL;
+ }
+
+ ret = fsl_esdhc_initialize(bis, &usdhc_cfg[i]);
+ if (ret) {
+ printf("Warning: failed to initialize mmc dev %d\n", i);
+ return ret;
+ }
+ }
+ return 0;
+}
+
+iomux_v3_cfg_t const ecspi2_pads[] = {
+ MX6_PAD_CSI_DATA00__ECSPI2_SCLK | MUX_PAD_CTRL(SPI_PAD_CTRL),
+ MX6_PAD_CSI_DATA02__ECSPI2_MOSI | MUX_PAD_CTRL(SPI_PAD_CTRL),
+ MX6_PAD_CSI_DATA03__ECSPI2_MISO | MUX_PAD_CTRL(SPI_PAD_CTRL),
+ MX6_PAD_CSI_DATA01__GPIO4_IO22 | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+int board_spi_cs_gpio(unsigned int bus, unsigned int cs)
+{
+ return (bus == CONFIG_SF_DEFAULT_BUS && cs == CONFIG_SF_DEFAULT_CS)
+ ? (IMX_GPIO_NR(4, 22)) : -1;
+}
+
+static void setup_spi(void)
+{
+ gpio_request(IMX_GPIO_NR(4, 22), "spi2_cs0");
+ gpio_direction_output(IMX_GPIO_NR(4, 22), 1);
+ imx_iomux_v3_setup_multiple_pads(ecspi2_pads, ARRAY_SIZE(ecspi2_pads));
+
+ enable_spi_clk(true, 1);
+}
+
+static iomux_v3_cfg_t const uart4_pads[] = {
+ MX6_PAD_UART4_TX_DATA__UART4_DCE_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
+ MX6_PAD_UART4_RX_DATA__UART4_DCE_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+static void setup_iomux_uart(void)
+{
+ imx_iomux_v3_setup_multiple_pads(uart4_pads, ARRAY_SIZE(uart4_pads));
+}
+
+// DDR 256MB (Hynix H5TQ2G63DFR)
+static struct mx6_ddr3_cfg mem_256M_ddr = {
+ .mem_speed = 800,
+ .density = 2,
+ .width = 16,
+ .banks = 8,
+ .rowaddr = 14,
+ .coladdr = 10,
+ .pagesz = 2,
+ .trcd = 1350,
+ .trcmin = 4950,
+ .trasmin = 3600,
+};
+
+static struct mx6_mmdc_calibration mx6_mmcd_256M_calib = {
+ .p0_mpwldectrl0 = 0x00000000,
+ .p0_mpdgctrl0 = 0x01340134,
+ .p0_mprddlctl = 0x40405052,
+ .p0_mpwrdlctl = 0x40404E48,
+};
+
+// DDR 512MB (Hynix H5TQ4G63DFR)
+static struct mx6_ddr3_cfg mem_512M_ddr = {
+ .mem_speed = 800,
+ .density = 4,
+ .width = 16,
+ .banks = 8,
+ .rowaddr = 15,
+ .coladdr = 10,
+ .pagesz = 2,
+ .trcd = 1350,
+ .trcmin = 4950,
+ .trasmin = 3600,
+};
+
+static struct mx6_mmdc_calibration mx6_mmcd_512M_calib = {
+ .p0_mpwldectrl0 = 0x00000000,
+ .p0_mpdgctrl0 = 0X01440144,
+ .p0_mprddlctl = 0x40405454,
+ .p0_mpwrdlctl = 0x40404E4C,
+};
+
+// Common DDR parameters (256MB and 512MB)
+static struct mx6ul_iomux_grp_regs mx6_grp_ioregs = {
+ .grp_addds = 0x00000028,
+ .grp_ddrmode_ctl = 0x00020000,
+ .grp_b0ds = 0x00000028,
+ .grp_ctlds = 0x00000028,
+ .grp_b1ds = 0x00000028,
+ .grp_ddrpke = 0x00000000,
+ .grp_ddrmode = 0x00020000,
+ .grp_ddr_type = 0x000c0000,
+};
+
+static struct mx6ul_iomux_ddr_regs mx6_ddr_ioregs = {
+ .dram_dqm0 = 0x00000028,
+ .dram_dqm1 = 0x00000028,
+ .dram_ras = 0x00000028,
+ .dram_cas = 0x00000028,
+ .dram_odt0 = 0x00000028,
+ .dram_odt1 = 0x00000028,
+ .dram_sdba2 = 0x00000000,
+ .dram_sdclk_0 = 0x00000028,
+ .dram_sdqs0 = 0x00000028,
+ .dram_sdqs1 = 0x00000028,
+ .dram_reset = 0x00000028,
+};
+
+struct mx6_ddr_sysinfo ddr_sysinfo = {
+ .dsize = 0,
+ .cs_density = 20,
+ .ncs = 1,
+ .cs1_mirror = 0,
+ .rtt_wr = 2,
+ .rtt_nom = 1, /* RTT_Nom = RZQ/2 */
+ .walat = 1, /* Write additional latency */
+ .ralat = 5, /* Read additional latency */
+ .mif3_mode = 3, /* Command prediction working mode */
+ .bi_on = 1, /* Bank interleaving enabled */
+ .sde_to_rst = 0x10, /* 14 cycles, 200us (JEDEC default) */
+ .rst_to_cke = 0x23, /* 33 cycles, 500us (JEDEC default) */
+ .ddr_type = DDR_TYPE_DDR3,
+ .refsel = 0, /* Refresh cycles at 64KHz */
+ .refr = 1, /* 2 refresh commands per refresh cycle */
+};
+
+static void ccgr_init(void)
+{
+ struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
+
+ writel(0xFFFFFFFF, &ccm->CCGR0);
+ writel(0xFFFFFFFF, &ccm->CCGR1);
+ writel(0xFFFFFFFF, &ccm->CCGR2);
+ writel(0xFFFFFFFF, &ccm->CCGR3);
+ writel(0xFFFFFFFF, &ccm->CCGR4);
+ writel(0xFFFFFFFF, &ccm->CCGR5);
+ writel(0xFFFFFFFF, &ccm->CCGR6);
+ writel(0xFFFFFFFF, &ccm->CCGR7);
+}
+
+static void spl_dram_init(void)
+{
+ unsigned int size;
+
+ // DDR RAM connection is always 16 bit wide. Init IOs.
+ mx6ul_dram_iocfg(16, &mx6_ddr_ioregs, &mx6_grp_ioregs);
+
+ // Try to detect the 512MB RAM chip first.
+ mx6_dram_cfg(&ddr_sysinfo, &mx6_mmcd_512M_calib, &mem_512M_ddr);
+
+ // Get the available RAM size
+ size = get_ram_size((void *)PHYS_SDRAM, SZ_512M);
+
+ gd->ram_size = size;
+
+ if (size == SZ_512M) {
+ // 512MB RAM was detected
+ return;
+ } else if (size == SZ_256M) {
+ // 256MB RAM was detected, use correct config and calibration
+ mx6_dram_cfg(&ddr_sysinfo, &mx6_mmcd_256M_calib, &mem_256M_ddr);
+ } else {
+ printf("Invalid DDR RAM size detected: %x\n", size);
+ }
+}
+
+static int do_board_detect(void)
+{
+ if (is_mx6ul())
+ gd->board_type = BOARD_TYPE_KTN_N631X;
+ else if (is_mx6ull())
+ gd->board_type = BOARD_TYPE_KTN_N641X;
+
+ printf("Kontron SL i.MX6UL%s (N6%s1x) module, %lu MB RAM detected\n",
+ is_mx6ull() ? "L" : "", is_mx6ull() ? "4" : "3", gd->ram_size / SZ_1M);
+
+ return 0;
+}
+
+void board_init_f(ulong dummy)
+{
+ ccgr_init();
+
+ /* setup AIPS and disable watchdog */
+ arch_cpu_init();
+
+ /* iomux and setup of UART and SPI */
+ board_early_init_f();
+
+ /* setup GP timer */
+ timer_init();
+
+ /* UART clocks enabled and gd valid - init serial console */
+ preloader_console_init();
+
+ /* DDR initialization */
+ spl_dram_init();
+
+ /* Clear the BSS. */
+ memset(__bss_start, 0, __bss_end - __bss_start);
+
+ /* Detect the board type */
+ do_board_detect();
+
+ /* load/boot image from boot device */
+ board_init_r(NULL, 0);
+}
+
+void board_boot_order(u32 *spl_boot_list)
+{
+ u32 bootdev = spl_boot_device();
+
+ /*
+ * The default boot fuse settings use the SD card (MMC1) as primary
+ * boot device, but allow SPI NOR as a fallback boot device.
+ * We can't detect the fallback case and spl_boot_device() will return
+ * BOOT_DEVICE_MMC1 despite the actual boot device being SPI NOR.
+ * Therefore we try to load U-Boot proper vom SPI NOR after loading
+ * from MMC has failed.
+ */
+ spl_boot_list[0] = bootdev;
+
+ switch (bootdev) {
+ case BOOT_DEVICE_MMC1:
+ case BOOT_DEVICE_MMC2:
+ spl_boot_list[1] = BOOT_DEVICE_SPI;
+ break;
+ }
+}
+
+int board_early_init_f(void)
+{
+ setup_iomux_uart();
+ setup_spi();
+
+ return 0;
+}
+
+int board_fit_config_name_match(const char *name)
+{
+ if (gd->board_type == BOARD_TYPE_KTN_N631X && is_mx6ul() &&
+ !strcmp(name, "imx6ul-kontron-n631x-s"))
+ return 0;
+
+ if (gd->board_type == BOARD_TYPE_KTN_N641X && is_mx6ull() &&
+ !strcmp(name, "imx6ull-kontron-n641x-s"))
+ return 0;
+
+ return -1;
+}
--- /dev/null
+CONFIG_ARM=y
+CONFIG_ARCH_MX6=y
+CONFIG_SYS_TEXT_BASE=0x87800000
+CONFIG_SPL_GPIO=y
+CONFIG_SPL_LIBCOMMON_SUPPORT=y
+CONFIG_SPL_LIBGENERIC_SUPPORT=y
+CONFIG_NR_DRAM_BANKS=1
+CONFIG_SYS_MEMTEST_START=0x80000000
+CONFIG_SYS_MEMTEST_END=0x90000000
+CONFIG_ENV_SIZE=0x10000
+CONFIG_ENV_OFFSET=0xF0000
+CONFIG_ENV_SECT_SIZE=0x10000
+CONFIG_MX6UL=y
+CONFIG_TARGET_KONTRON_MX6UL=y
+CONFIG_SYS_MALLOC_LEN=0x4000000
+CONFIG_DM_GPIO=y
+CONFIG_DEFAULT_DEVICE_TREE="imx6ul-kontron-n631x-s"
+CONFIG_SPL_TEXT_BASE=0x00908000
+CONFIG_SPL_MMC_SUPPORT=y
+CONFIG_SPL_SERIAL_SUPPORT=y
+CONFIG_BOOTCOUNT_BOOTLIMIT=3
+CONFIG_SPL=y
+CONFIG_SPL_SPI_FLASH_SUPPORT=y
+CONFIG_SPL_SPI_SUPPORT=y
+CONFIG_DISTRO_DEFAULTS=y
+CONFIG_FIT=y
+CONFIG_SPL_LOAD_FIT=y
+# CONFIG_USE_SPL_FIT_GENERATOR is not set
+CONFIG_OF_BOARD_SETUP=y
+CONFIG_IMX_CONFIG="arch/arm/mach-imx/spl_sd.cfg"
+CONFIG_SYS_CONSOLE_IS_IN_ENV=y
+CONFIG_BOARD_TYPES=y
+CONFIG_BOARD_EARLY_INIT_F=y
+CONFIG_SPL_RAW_IMAGE_SUPPORT=y
+CONFIG_SPL_LEGACY_IMAGE_SUPPORT=y
+CONFIG_SPL_LEGACY_IMAGE_CRC_CHECK=y
+CONFIG_SPL_SEPARATE_BSS=y
+CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0x8A
+CONFIG_SPL_SPI_LOAD=y
+CONFIG_SYS_SPI_U_BOOT_OFFS=0x11400
+CONFIG_SPL_USB_HOST=y
+CONFIG_SPL_USB_GADGET=y
+CONFIG_SPL_USB_SDP_SUPPORT=y
+CONFIG_SPL_WATCHDOG=y
+CONFIG_CMD_MEMTEST=y
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_MTD=y
+CONFIG_CMD_SF_TEST=y
+CONFIG_CMD_USB=y
+CONFIG_CMD_USB_SDP=y
+CONFIG_CMD_USB_MASS_STORAGE=y
+CONFIG_CMD_CACHE=y
+CONFIG_CMD_EXT4_WRITE=y
+CONFIG_CMD_FS_UUID=y
+CONFIG_CMD_MTDPARTS=y
+CONFIG_MTDIDS_DEFAULT="nor0=spi1.0,spi-nand0=spi4.0"
+CONFIG_MTDPARTS_DEFAULT="mtdparts=spi1.0:128k(spl),832k(u-boot),64k(env);spi4.0:-(UBI)"
+CONFIG_CMD_UBI=y
+CONFIG_OF_CONTROL=y
+CONFIG_SPL_OF_CONTROL=y
+CONFIG_OF_LIST="imx6ul-kontron-n631x-s imx6ull-kontron-n641x-s"
+CONFIG_ENV_OVERWRITE=y
+CONFIG_ENV_IS_IN_MMC=y
+CONFIG_ENV_IS_IN_SPI_FLASH=y
+CONFIG_USE_ENV_SPI_BUS=y
+CONFIG_ENV_SPI_BUS=2
+CONFIG_BOOTCOUNT_LIMIT=y
+CONFIG_BOOTCOUNT_ENV=y
+CONFIG_DM_I2C=y
+CONFIG_FSL_USDHC=y
+CONFIG_MTD=y
+CONFIG_DM_MTD=y
+CONFIG_MTD_SPI_NAND=y
+CONFIG_DM_SPI_FLASH=y
+CONFIG_SF_DEFAULT_BUS=1
+CONFIG_SF_DEFAULT_MODE=0
+CONFIG_SF_DEFAULT_SPEED=10000000
+CONFIG_SPI_FLASH_MACRONIX=y
+CONFIG_SPI_FLASH_WINBOND=y
+CONFIG_SPI_FLASH_MTD=y
+CONFIG_PHYLIB=y
+CONFIG_PHY_MICREL=y
+CONFIG_PHY_MICREL_KSZ8XXX=y
+CONFIG_DM_ETH=y
+CONFIG_DM_ETH_PHY=y
+CONFIG_FEC_MXC=y
+CONFIG_MII=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_IMX6=y
+CONFIG_DM_REGULATOR=y
+CONFIG_DM_REGULATOR_FIXED=y
+CONFIG_DM_REGULATOR_GPIO=y
+CONFIG_CONS_INDEX=4
+CONFIG_MXC_UART=y
+CONFIG_SPI=y
+CONFIG_DM_SPI=y
+CONFIG_FSL_QSPI=y
+CONFIG_MXC_SPI=y
+CONFIG_IMX_THERMAL=y
+CONFIG_USB=y
+CONFIG_USB_GADGET=y
+CONFIG_USB_GADGET_MANUFACTURER="FSL"
+CONFIG_USB_GADGET_VENDOR_NUM=0x0525
+CONFIG_USB_GADGET_PRODUCT_NUM=0xa4a5
+CONFIG_CI_UDC=y
+CONFIG_USB_GADGET_DOWNLOAD=y
+CONFIG_FDT_FIXUP_PARTITIONS=y
:maxdepth: 2
sl28
+ sl-mx6ul
--- /dev/null
+.. SPDX-License-Identifier: GPL-2.0+
+
+Kontron Electronics SL i.MX6UL/ULL SoM
+======================================
+
+The Kontron SoM-Line i.MX6UL/ULL (N6x1x) by Kontron Electronics GmbH is a SoM module
+with either an i.MX6UL or i.MX6ULL SoC, 256/512 MB DDR3 RAM, SPI NOR, SPI NAND and Ethernet PHY.
+
+The matching evaluation boards (Board-Line) have two Ethernet ports, USB 2.0,
+RGB, SD card, CAN, RS485, RS232 and much more.
+
+Quick Start
+-----------
+
+- Build U-Boot
+- Boot
+
+Build U-Boot
+^^^^^^^^^^^^
+
+.. code-block:: bash
+
+ $ make kontron-sl-mx6ul_defconfig
+ $ make
+
+Burn the flash.bin to SD card at an offset of 1 KiB:
+
+.. code-block:: bash
+
+ $ dd if=flash.bin of=/dev/sd[x] bs=1K seek=1 conv=notrunc
+
+Boot
+^^^^
+
+Put the SD card in the slot on the board and apply power.
+
+Further Information
+-------------------
+
+The bootloader configuration is setup to be used with kernel FIT images. Legacy
+images might not be working out of the box.
+
+Please see https://docs.kontron-electronics.de for further vendor documentation.
--- /dev/null
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * Copyright (C) 2018 Kontron Electronics GmbH
+ *
+ * Configuration settings for the Kontron i.MX6UL boards/SoMs.
+ */
+#ifndef __KONTRON_MX6UL_CONFIG_H
+#define __KONTRON_MX6UL_CONFIG_H
+
+#include <asm/arch/imx-regs.h>
+#include <linux/sizes.h>
+
+#include "mx6_common.h"
+#ifdef CONFIG_SPL_BUILD
+#include "imx6_spl.h"
+#endif
+
+/* RAM */
+#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR
+#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM
+
+#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR
+#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE
+
+#define CONFIG_SYS_HZ 1000
+
+#define CONFIG_SYS_INIT_SP_OFFSET \
+ (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_ADDR \
+ (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
+
+#define CONFIG_SYS_UBOOT_BASE CONFIG_SYS_TEXT_BASE
+
+/* Board and environment settings */
+#define CONFIG_MXC_UART_BASE UART4_BASE
+#define CONFIG_HOSTNAME "kontron-mx6ul"
+#define CONFIG_ETHPRIME "eth0"
+
+#ifdef CONFIG_USB_EHCI_HCD
+#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
+#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW)
+#define CONFIG_MXC_USB_FLAGS 0
+#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
+#endif
+
+/* Boot order for distro boot */
+#ifndef CONFIG_SPL_BUILD
+#define BOOT_TARGET_DEVICES(func) \
+ func(MMC, mmc, 1) \
+ func(MMC, mmc, 0) \
+ func(UBIFS, ubifs, 0) \
+ func(USB, usb, 0) \
+ func(PXE, pxe, na) \
+ func(DHCP, dhcp, na)
+#include <config_distro_bootcmd.h>
+#else
+#define BOOTENV
+#endif
+
+/* MMC Configs */
+#ifdef CONFIG_FSL_USDHC
+#define CONFIG_SYS_FSL_ESDHC_ADDR USDHC1_BASE_ADDR
+#define CONFIG_SYS_FSL_USDHC_NUM 2
+#define CONFIG_SYS_MMC_IMG_LOAD_PART 1
+#endif
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "kernel_addr_r=0x82000000\0" \
+ "ramdisk_addr_r=0x88080000\0" \
+ "pxefile_addr_r=0x80100000\0" \
+ "scriptaddr=0x80100000\0" \
+ "bootdelay=3\0" \
+ "ethact=" CONFIG_ETHPRIME "\0" \
+ "hostname=" CONFIG_HOSTNAME "\0" \
+ BOOTENV
+
+#endif /* __KONTRON_MX6UL_CONFIG_H */
projects / platform / kernel / u-boot.git / commitdiff