#ifndef __IGEP00X0_H
#define __IGEP00X0_H
-#include <asm/sizes.h>
-
-/*
- * High Level Configuration Options
- */
-#define CONFIG_OMAP 1 /* in a TI OMAP core */
-#define CONFIG_OMAP34XX 1 /* which is a 34XX */
-#define CONFIG_OMAP_GPIO
-#define CONFIG_OMAP_COMMON
+#ifdef CONFIG_BOOT_NAND
+#define CONFIG_NAND
+#endif
-#define CONFIG_SDRC /* The chip has SDRC controller */
+#define CONFIG_NR_DRAM_BANKS 2
-#include <asm/arch/cpu.h>
-#include <asm/arch/omap3.h>
+#include <configs/ti_omap3_common.h>
#include <asm/mach-types.h>
/*
#define CONFIG_DISPLAY_CPUINFO 1
#define CONFIG_DISPLAY_BOARDINFO 1
-/* Clock Defines */
-#define V_OSCK 26000000 /* Clock output from T2 */
-#define V_SCLK (V_OSCK >> 1)
-
#define CONFIG_MISC_INIT_R
-#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */
-#define CONFIG_SETUP_MEMORY_TAGS 1
-#define CONFIG_INITRD_TAG 1
#define CONFIG_REVISION_TAG 1
-#define CONFIG_OF_LIBFDT
-#define CONFIG_CMD_BOOTZ
#define CONFIG_SUPPORT_RAW_INITRD
-/*
- * NS16550 Configuration
- */
-
-#define V_NS16550_CLK 48000000 /* 48MHz (APLL96/2) */
-
-#define CONFIG_SYS_NS16550
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE (-4)
-#define CONFIG_SYS_NS16550_CLK V_NS16550_CLK
-
-/* select serial console configuration */
-#define CONFIG_CONS_INDEX 3
-#define CONFIG_SYS_NS16550_COM3 OMAP34XX_UART3
-#define CONFIG_SERIAL3 3
-
-/* allow to overwrite serial and ethaddr */
-#define CONFIG_ENV_OVERWRITE
-#define CONFIG_BAUDRATE 115200
-#define CONFIG_SYS_BAUDRATE_TABLE {4800, 9600, 19200, 38400, 57600, \
- 115200}
-#define CONFIG_GENERIC_MMC 1
-#define CONFIG_MMC 1
-#define CONFIG_OMAP_HSMMC 1
-#define CONFIG_DOS_PARTITION 1
-
/* define to enable boot progress via leds */
#if (CONFIG_MACH_TYPE == MACH_TYPE_IGEP0020) || \
(CONFIG_MACH_TYPE == MACH_TYPE_IGEP0030)
#define CONFIG_USBD_MANUFACTURER "Texas Instruments"
#define CONFIG_USBD_PRODUCT_NAME "IGEP"
-/* commands to include */
-#include <config_cmd_default.h>
-
#define CONFIG_CMD_CACHE
-#define CONFIG_CMD_EXT4
-#define CONFIG_CMD_FAT /* FAT support */
-#define CONFIG_CMD_FS_GENERIC
-#define CONFIG_CMD_I2C /* I2C serial bus support */
-#define CONFIG_CMD_MMC /* MMC support */
#ifdef CONFIG_BOOT_ONENAND
#define CONFIG_CMD_ONENAND /* ONENAND support */
#endif
-#ifdef CONFIG_BOOT_NAND
-#define CONFIG_CMD_NAND
-#endif
#if (CONFIG_MACH_TYPE == MACH_TYPE_IGEP0020) || \
(CONFIG_MACH_TYPE == MACH_TYPE_IGEP0032)
#define CONFIG_CMD_NET /* bootp, tftpboot, rarpboot */
#define CONFIG_CMD_DHCP
#define CONFIG_CMD_PING
#define CONFIG_CMD_NFS /* NFS support */
-#define CONFIG_CMD_MTDPARTS /* Enable MTD parts commands */
-#define CONFIG_MTD_DEVICE
-
-#undef CONFIG_CMD_FLASH /* flinfo, erase, protect */
-#undef CONFIG_CMD_IMLS /* List all found images */
-#define CONFIG_SYS_NO_FLASH
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_OMAP34XX
-#define CONFIG_SYS_OMAP24_I2C_SPEED 100000
-#define CONFIG_SYS_OMAP24_I2C_SLAVE 1
-
-/*
- * TWL4030
- */
-#define CONFIG_TWL4030_POWER 1
-
-#define CONFIG_BOOTDELAY 3
+/*#undef CONFIG_ENV_IS_NOWHERE*/
#define CONFIG_EXTRA_ENV_SETTINGS \
"usbtty=cdc_acm\0" \
"fi;" \
"run nandboot;" \
-#define CONFIG_AUTO_COMPLETE 1
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */
-#define CONFIG_SYS_PROMPT "U-Boot # "
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-/* Print Buffer Size */
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
- sizeof(CONFIG_SYS_PROMPT) + 16)
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-/* Boot Argument Buffer Size */
-#define CONFIG_SYS_BARGSIZE (CONFIG_SYS_CBSIZE)
-
-#define CONFIG_SYS_MEMTEST_START (OMAP34XX_SDRC_CS0) /* memtest */
- /* works on */
-#define CONFIG_SYS_MEMTEST_END (OMAP34XX_SDRC_CS0 + \
- 0x01F00000) /* 31MB */
-
-#define CONFIG_SYS_LOAD_ADDR (OMAP34XX_SDRC_CS0) /* default */
- /* load address */
-
-#define CONFIG_SYS_MONITOR_LEN (256 << 10)
-
-/*
- * OMAP3 has 12 GP timers, they can be driven by the system clock
- * (12/13/16.8/19.2/38.4MHz) or by 32KHz clock. We use 13MHz (V_SCLK).
- * This rate is divided by a local divisor.
- */
-#define CONFIG_SYS_TIMERBASE (OMAP34XX_GPT2)
-#define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */
-
-/*
- * Physical Memory Map
- *
- */
-#define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */
-#define PHYS_SDRAM_1 OMAP34XX_SDRC_CS0
-#define PHYS_SDRAM_2 OMAP34XX_SDRC_CS1
-
/*
* FLASH and environment organization
*/
#define CONFIG_ENV_ADDR ONENAND_ENV_OFFSET
#endif
-#ifdef CONFIG_BOOT_NAND
+#ifdef CONFIG_NAND
#define PISMO1_NAND_SIZE GPMC_SIZE_128M /* Configure the PISMO */
-#define CONFIG_NAND_OMAP_GPMC
-#define CONFIG_SYS_NAND_BASE NAND_BASE
#define GPMC_NAND_ECC_LP_x16_LAYOUT 1
#define CONFIG_ENV_OFFSET 0x260000 /* environment starts here */
#define CONFIG_ENV_IS_IN_NAND 1
#define CONFIG_ENV_SIZE (512 << 10) /* Total Size Environment */
#define CONFIG_ENV_ADDR NAND_ENV_OFFSET
-#define CONFIG_SYS_MAX_NAND_DEVICE 1
#endif
/*
- * Size of malloc() pool
- */
-#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (128 << 10))
-
-/*
* SMSC911x Ethernet
*/
#if defined(CONFIG_CMD_NET)
#define CONFIG_SMC911X_BASE 0x2C000000
#endif /* (CONFIG_CMD_NET) */
-/*
- * Leave it at 0x80008000 to allow booting new u-boot.bin with X-loader
- * and older u-boot.bin with the new U-Boot SPL.
- */
-#define CONFIG_SYS_TEXT_BASE 0x80008000
-#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
-#define CONFIG_SYS_INIT_RAM_ADDR 0x4020f800
-#define CONFIG_SYS_INIT_RAM_SIZE 0x800
-#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \
- CONFIG_SYS_INIT_RAM_SIZE - \
- GENERATED_GBL_DATA_SIZE)
-
-/* SPL */
-#define CONFIG_SPL
-#define CONFIG_SPL_FRAMEWORK
-#define CONFIG_SPL_NAND_SIMPLE
-#define CONFIG_SPL_TEXT_BASE 0x40200800
-#define CONFIG_SPL_MAX_SIZE (54 * 1024)
-#define CONFIG_SPL_STACK LOW_LEVEL_SRAM_STACK
-
-/* move malloc and bss high to prevent clashing with the main image */
-#define CONFIG_SYS_SPL_MALLOC_START 0x87000000
-#define CONFIG_SYS_SPL_MALLOC_SIZE 0x80000
-#define CONFIG_SPL_BSS_START_ADDR 0x87080000 /* end of minimum RAM */
-#define CONFIG_SPL_BSS_MAX_SIZE 0x80000 /* 512 KB */
-
-/* MMC boot config */
-#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x300 /* address 0x60000 */
-#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x200 /* 256 KB */
-#define CONFIG_SYS_MMC_SD_FAT_BOOT_PARTITION 1
-#define CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME "u-boot.img"
-
-#define CONFIG_SPL_BOARD_INIT
-#define CONFIG_SPL_LIBCOMMON_SUPPORT
-#define CONFIG_SPL_LIBDISK_SUPPORT
-#define CONFIG_SPL_I2C_SUPPORT
-#define CONFIG_SPL_LIBGENERIC_SUPPORT
-#define CONFIG_SPL_MMC_SUPPORT
-#define CONFIG_SPL_FAT_SUPPORT
-#define CONFIG_SPL_SERIAL_SUPPORT
-
-#define CONFIG_SPL_POWER_SUPPORT
-#define CONFIG_SPL_LDSCRIPT "$(CPUDIR)/omap-common/u-boot-spl.lds"
-
+/* OneNAND boot config */
#ifdef CONFIG_BOOT_ONENAND
#define CONFIG_SPL_ONENAND_SUPPORT
-
-/* OneNAND boot config */
#define CONFIG_SYS_ONENAND_U_BOOT_OFFS 0x80000
#define CONFIG_SYS_ONENAND_PAGE_SIZE 2048
#define CONFIG_SPL_ONENAND_LOAD_ADDR 0x80000
#endif
-#ifdef CONFIG_BOOT_NAND
-#define CONFIG_SPL_NAND_SUPPORT
-#define CONFIG_SPL_NAND_BASE
-#define CONFIG_SPL_NAND_DRIVERS
-#define CONFIG_SPL_NAND_ECC
-
/* NAND boot config */
+#ifdef CONFIG_NAND
#define CONFIG_SYS_NAND_5_ADDR_CYCLE
#define CONFIG_SYS_NAND_PAGE_COUNT 64
#define CONFIG_SYS_NAND_PAGE_SIZE 2048
#define CONFIG_SYS_NAND_ECCSIZE 512
#define CONFIG_SYS_NAND_ECCBYTES 3
#define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_HAM1_CODE_HW
-#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE
-#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000
#endif
#endif /* __IGEP00X0_H */
projects / platform / kernel / u-boot.git / commitdiff