u8 size;
u8 checksum;
void *mrst_gct;
-} __attribute__ ((packed));
+} __packed;
struct mrst_timing_info {
u16 pixel_clock;
u8 stereo:1;
u8 unknown6:1;
u8 interlaced:1;
-} __attribute__((packed));
+} __packed;
struct gct_r10_timing_info {
u16 pixel_clock;
u16 vsync_pulse_width_hi:2;
u16 vsync_positive:1;
u16 rsvd_2:3;
-} __attribute__((packed));
+} __packed;
struct mrst_panel_descriptor_v1 {
u32 Panel_Port_Control; /* 1 dword, Register 0x61180 if LVDS */
/* Bit 6, Reserved, 2 bits, 00b */
/* Bit 8, Minimum Supported Frame Rate, 6 bits, 0 - 63Hz */
/* Bit 14, Reserved, 2 bits, 00b */
-} __attribute__ ((packed));
+} __packed;
struct mrst_panel_descriptor_v2 {
u32 Panel_Port_Control; /* 1 dword, Register 0x61180 if LVDS */
/* Bit 6, Reserved, 2 bits, 00b */
/* Bit 8, Minimum Supported Frame Rate, 6 bits, 0 - 63Hz */
/* Bit 14, Reserved, 2 bits, 00b */
-} __attribute__ ((packed));
+} __packed;
union mrst_panel_rx {
- struct{
+ struct {
u16 NumberOfLanes:2; /*Num of Lanes, 2 bits,0 = 1 lane,*/
/* 1 = 2 lanes, 2 = 3 lanes, 3 = 4 lanes. */
u16 MaxLaneFreq:3; /* 0: 100MHz, 1: 200MHz, 2: 300MHz, */
u16 Rsvd:5;/*5 bits,00000b */
} panelrx;
u16 panel_receiver;
-} __attribute__ ((packed));
+} __packed;
struct mrst_gct_v1 {
- union{ /*8 bits,Defined as follows: */
+ union { /*8 bits,Defined as follows: */
struct {
u8 PanelType:4; /*4 bits, Bit field for panels*/
/* 0 - 3: 0 = LVDS, 1 = MIPI*/
};
struct mrst_panel_descriptor_v1 panel[4];/*panel descrs,38 bytes each*/
union mrst_panel_rx panelrx[4]; /* panel receivers*/
-} __attribute__ ((packed));
+} __packed;
struct mrst_gct_v2 {
- union{ /*8 bits,Defined as follows: */
+ union { /*8 bits,Defined as follows: */
struct {
u8 PanelType:4; /*4 bits, Bit field for panels*/
/* 0 - 3: 0 = LVDS, 1 = MIPI*/
};
struct mrst_panel_descriptor_v2 panel[4];/*panel descrs,38 bytes each*/
union mrst_panel_rx panelrx[4]; /* panel receivers*/
-} __attribute__ ((packed));
+} __packed;
struct mrst_gct_data {
u8 bpi; /* boot panel index, number of panel used during boot */
u32 PP_Cycle_Delay;
u16 Panel_Backlight_Inverter_Descriptor;
u16 Panel_MIPI_Display_Descriptor;
-} __attribute__ ((packed));
+} __packed;
-#define MODE_SETTING_IN_CRTC 0x1
-#define MODE_SETTING_IN_ENCODER 0x2
-#define MODE_SETTING_ON_GOING 0x3
-#define MODE_SETTING_IN_DSR 0x4
-#define MODE_SETTING_ENCODER_DONE 0x8
-#define GCT_R10_HEADER_SIZE 16
-#define GCT_R10_DISPLAY_DESC_SIZE 28
+#define MODE_SETTING_IN_CRTC 0x1
+#define MODE_SETTING_IN_ENCODER 0x2
+#define MODE_SETTING_ON_GOING 0x3
+#define MODE_SETTING_IN_DSR 0x4
+#define MODE_SETTING_ENCODER_DONE 0x8
+#define GCT_R10_HEADER_SIZE 16
+#define GCT_R10_DISPLAY_DESC_SIZE 28
/* This ifdef can go once the cpu ident stuff is cleaned up in arch */
#if defined(CONFIG_X86_MRST)
if (mrst_identify_cpu())
- i2c_adap = i2c_get_adapter(2);
- else /* Oaktrail uses I2C 1 */
-#endif
- i2c_adap = i2c_get_adapter(1);
+ i2c_adap = i2c_get_adapter(2);
+ else /* Oaktrail uses I2C 1 */
+#endif
+ i2c_adap = i2c_get_adapter(1);
if (i2c_adap == NULL)
printk(KERN_ALERT "No ddc adapter available!\n");
void psb_spank(struct drm_psb_private *dev_priv)
{
- PSB_WSGX32(_PSB_CS_RESET_BIF_RESET | _PSB_CS_RESET_DPM_RESET |
+ PSB_WSGX32(_PSB_CS_RESET_BIF_RESET | _PSB_CS_RESET_DPM_RESET |
_PSB_CS_RESET_TA_RESET | _PSB_CS_RESET_USE_RESET |
_PSB_CS_RESET_ISP_RESET | _PSB_CS_RESET_TSP_RESET |
_PSB_CS_RESET_TWOD_RESET, PSB_CR_SOFT_RESET);
- (void) PSB_RSGX32(PSB_CR_SOFT_RESET);
+ PSB_RSGX32(PSB_CR_SOFT_RESET);
msleep(1);
uint32_t avail = PSB_RSGX32(PSB_CR_2D_SOCIF);
unsigned long t = jiffies + HZ;
- while(avail < size) {
+ while (avail < size) {
avail = PSB_RSGX32(PSB_CR_2D_SOCIF);
if (time_after(jiffies, t)) {
psb_spank(dev_priv);
it with console use */
int psbfb_2d_submit(struct drm_psb_private *dev_priv, uint32_t *cmdbuf,
- unsigned size)
+ unsigned size)
{
int ret = 0;
int i;
return ret;
submit_size <<= 2;
- for (i = 0; i < submit_size; i += 4) {
+
+ for (i = 0; i < submit_size; i += 4)
PSB_WSGX32(*cmdbuf++, PSB_SGX_2D_SLAVE_PORT + i);
- }
+
(void)PSB_RSGX32(PSB_SGX_2D_SLAVE_PORT + i - 4);
}
return 0;
{
if (xdir < 0)
return (ydir < 0) ? PSB_2D_COPYORDER_BR2TL :
- PSB_2D_COPYORDER_TR2BL;
+ PSB_2D_COPYORDER_TR2BL;
else
return (ydir < 0) ? PSB_2D_COPYORDER_BL2TR :
- PSB_2D_COPYORDER_TL2BR;
+ PSB_2D_COPYORDER_TL2BR;
}
/*
if (unlikely(info->state != FBINFO_STATE_RUNNING))
return;
- /* Avoid the 8 pixel erratum */
+ /* Avoid the 8 pixel erratum */
if (region->width == 8 || region->height == 8 ||
- (info->flags & FBINFO_HWACCEL_DISABLED))
+ (info->flags & FBINFO_HWACCEL_DISABLED))
return cfb_copyarea(info, region);
psbfb_copyarea_accel(info, region);
void psbfb_imageblit(struct fb_info *info, const struct fb_image *image)
{
- /* For now */
+ /* For now */
cfb_imageblit(info, image);
}
u32 OGAMC3;
u32 OGAMC4;
u32 OGAMC5;
- u32 IEP_ENABLED;
- u32 IEP_BLE_MINMAX;
- u32 IEP_BSSCC_CONTROL;
- u32 b_wait_vblank;
+ u32 IEP_ENABLED;
+ u32 IEP_BLE_MINMAX;
+ u32 IEP_BSSCC_CONTROL;
+ u32 b_wait_vblank;
} overlay;
u32 sprite_enable_mask;
module_param_named(trap_pagefaults, drm_psb_trap_pagefaults, int, 0600);
-static struct pci_device_id pciidlist[] = {
+static DEFINE_PCI_DEVICE_TABLE(pciidlist) = {
{ 0x8086, 0x8108, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_PSB_8108 },
{ 0x8086, 0x8109, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_PSB_8109 },
{ 0x8086, 0x4100, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_MRST_4100},
if (dev_priv->iLVDS_enable) {
dev_priv->is_lvds_on = true;
dev_priv->is_mipi_on = false;
- }
- else {
+ } else {
dev_priv->is_mipi_on = true;
dev_priv->is_lvds_on = false;
}
pci_write_config_dword(pci_root, 0xD0, FB_REG09);
pci_read_config_dword(pci_root, 0xD4, &fuse_value);
- DRM_INFO("SKU values is 0x%x. \n", fuse_value);
+ DRM_INFO("SKU values is 0x%x.\n", fuse_value);
fuse_value_tmp = (fuse_value & FB_SKU_MASK) >> FB_SKU_SHIFT;
dev_priv->fuse_reg_value = fuse_value;
pci_dev_put(pci_root);
}
-void mid_get_pci_revID (struct drm_psb_private *dev_priv)
+void mid_get_pci_revID(struct drm_psb_private *dev_priv)
{
uint32_t platform_rev_id = 0;
struct pci_dev *pci_gfx_root = pci_get_bus_and_slot(0, PCI_DEVFN(2, 0));
dev_priv->platform_rev_id = (uint8_t) platform_rev_id;
pci_dev_put(pci_gfx_root);
dev_info(dev_priv->dev->dev, "platform_rev_id is %x\n",
- dev_priv->platform_rev_id);
+ dev_priv->platform_rev_id);
}
void mrst_get_vbt_data(struct drm_psb_private *dev_priv)
dev_priv->gct_data.Panel_Port_Control =
((struct mrst_gct_v1 *)pGCT)->panel[bpi].Panel_Port_Control;
dev_priv->gct_data.Panel_MIPI_Display_Descriptor =
- ((struct mrst_gct_v1 *)pGCT)->panel[bpi].Panel_MIPI_Display_Descriptor;
+ ((struct mrst_gct_v1 *)pGCT)->panel[bpi].Panel_MIPI_Display_Descriptor;
break;
case 1:
vbt->mrst_gct = NULL;
dev_priv->gct_data.Panel_Port_Control =
((struct mrst_gct_v2 *)pGCT)->panel[bpi].Panel_Port_Control;
dev_priv->gct_data.Panel_MIPI_Display_Descriptor =
- ((struct mrst_gct_v2 *)pGCT)->panel[bpi].Panel_MIPI_Display_Descriptor;
+ ((struct mrst_gct_v2 *)pGCT)->panel[bpi].Panel_MIPI_Display_Descriptor;
break;
case 0x10:
/*header definition changed from rev 01 (v2) to rev 10h. */
PSB_WSGX32(0x00000000, PSB_CR_BIF_BANK0);
PSB_WSGX32(0x00000000, PSB_CR_BIF_BANK1);
PSB_RSGX32(PSB_CR_BIF_BANK1);
- PSB_WSGX32(PSB_RSGX32(PSB_CR_BIF_CTRL) | _PSB_MMU_ER_MASK,
+ PSB_WSGX32(PSB_RSGX32(PSB_CR_BIF_CTRL) | _PSB_MMU_ER_MASK,
PSB_CR_BIF_CTRL);
psb_spank(dev_priv);
/* mmu_gatt ?? */
- PSB_WSGX32(pg->gatt_start, PSB_CR_BIF_TWOD_REQ_BASE);
-
+ PSB_WSGX32(pg->gatt_start, PSB_CR_BIF_TWOD_REQ_BASE);
return 0;
out_err:
psb_do_takedown(dev);
dev_priv->rpm_enabled = 1;
}
return drm_ioctl(filp, cmd, arg);
-
/* FIXME: do we need to wrap the other side of this */
}
static struct drm_driver driver = {
.driver_features = DRIVER_HAVE_IRQ | DRIVER_IRQ_SHARED | \
- DRIVER_IRQ_VBL | DRIVER_MODESET| DRIVER_GEM ,
+ DRIVER_IRQ_VBL | DRIVER_MODESET | DRIVER_GEM ,
.load = psb_driver_load,
.unload = psb_driver_unload,
{
/* MLD Added this from Inaky's patch */
if (pci_enable_msi(pdev))
- dev_warn(&pdev->dev, "Enable MSI failed!\n");
+ dev_warn(&pdev->dev, "Enable MSI failed!\n");
return drm_get_pci_dev(pdev, ent, &driver);
}
#include <drm/drmP.h>
#include "drm_global.h"
+#include "gem_glue.h"
#include "psb_drm.h"
#include "psb_reg.h"
#include "psb_intel_drv.h"
#define _LNC_IRQ_TOPAZ_FLAG (1<<20)
/* This flag includes all the display IRQ bits excepts the vblank irqs. */
-#define _MDFLD_DISP_ALL_IRQ_FLAG (_MDFLD_PIPEC_EVENT_FLAG | _MDFLD_PIPEB_EVENT_FLAG | \
- _PSB_PIPEA_EVENT_FLAG | _PSB_VSYNC_PIPEA_FLAG | _MDFLD_MIPIA_FLAG | _MDFLD_MIPIC_FLAG)
+#define _MDFLD_DISP_ALL_IRQ_FLAG (_MDFLD_PIPEC_EVENT_FLAG | \
+ _MDFLD_PIPEB_EVENT_FLAG | \
+ _PSB_PIPEA_EVENT_FLAG | \
+ _PSB_VSYNC_PIPEA_FLAG | \
+ _MDFLD_MIPIA_FLAG | \
+ _MDFLD_MIPIC_FLAG)
#define PSB_INT_IDENTITY_R 0x20A4
#define PSB_INT_MASK_R 0x20A8
#define PSB_INT_ENABLE_R 0x20A0
/*
* Power
- */
+ */
bool suspended;
bool display_power;
uint32_t blc_adj1;
uint32_t blc_adj2;
- void * fbdev;
+ void *fbdev;
};
extern void psb_irq_turn_off_dpst(struct drm_device *dev);
extern void psb_irq_uninstall_islands(struct drm_device *dev, int hw_islands);
-extern int psb_vblank_wait2(struct drm_device *dev,unsigned int *sequence);
+extern int psb_vblank_wait2(struct drm_device *dev, unsigned int *sequence);
extern int psb_vblank_wait(struct drm_device *dev, unsigned int *sequence);
extern int psb_enable_vblank(struct drm_device *dev, int crtc);
extern void psb_disable_vblank(struct drm_device *dev, int crtc);
extern void psb_spank(struct drm_psb_private *dev_priv);
extern int psbfb_2d_submit(struct drm_psb_private *dev_priv, uint32_t *cmdbuf,
- unsigned size);
+ unsigned size);
/*
* psb_reset.c
/* modesetting */
extern void psb_modeset_init(struct drm_device *dev);
extern void psb_modeset_cleanup(struct drm_device *dev);
-extern int psb_fbdev_init(struct drm_device * dev);
+extern int psb_fbdev_init(struct drm_device *dev);
/* psb_bl.c */
int psb_backlight_init(struct drm_device *dev);
void psb_backlight_exit(void);
int psb_set_brightness(struct backlight_device *bd);
int psb_get_brightness(struct backlight_device *bd);
-struct backlight_device * psb_get_backlight_device(void);
+struct backlight_device *psb_get_backlight_device(void);
/* mrst_crtc.c */
extern const struct drm_crtc_helper_funcs mrst_helper_funcs;
extern int drm_psb_no_fb;
extern int drm_idle_check_interval;
-
/*
* Utilities
*/
{
int mcr = (0xD0<<24) | (port << 16) | (offset << 8);
uint32_t ret_val = 0;
- struct pci_dev *pci_root = pci_get_bus_and_slot (0, 0);
- pci_write_config_dword (pci_root, 0xD0, mcr);
- pci_read_config_dword (pci_root, 0xD4, &ret_val);
+ struct pci_dev *pci_root = pci_get_bus_and_slot(0, 0);
+ pci_write_config_dword(pci_root, 0xD0, mcr);
+ pci_read_config_dword(pci_root, 0xD4, &ret_val);
pci_dev_put(pci_root);
return ret_val;
}
static inline void MRST_MSG_WRITE32(uint port, uint offset, u32 value)
{
int mcr = (0xE0<<24) | (port << 16) | (offset << 8) | 0xF0;
- struct pci_dev *pci_root = pci_get_bus_and_slot (0, 0);
- pci_write_config_dword (pci_root, 0xD4, value);
- pci_write_config_dword (pci_root, 0xD0, mcr);
+ struct pci_dev *pci_root = pci_get_bus_and_slot(0, 0);
+ pci_write_config_dword(pci_root, 0xD4, value);
+ pci_write_config_dword(pci_root, 0xD0, mcr);
pci_dev_put(pci_root);
}
static inline u32 MDFLD_MSG_READ32(uint port, uint offset)
{
int mcr = (0x10<<24) | (port << 16) | (offset << 8);
uint32_t ret_val = 0;
- struct pci_dev *pci_root = pci_get_bus_and_slot (0, 0);
- pci_write_config_dword (pci_root, 0xD0, mcr);
- pci_read_config_dword (pci_root, 0xD4, &ret_val);
+ struct pci_dev *pci_root = pci_get_bus_and_slot(0, 0);
+ pci_write_config_dword(pci_root, 0xD0, mcr);
+ pci_read_config_dword(pci_root, 0xD4, &ret_val);
pci_dev_put(pci_root);
return ret_val;
}
static inline void MDFLD_MSG_WRITE32(uint port, uint offset, u32 value)
{
int mcr = (0x11<<24) | (port << 16) | (offset << 8) | 0xF0;
- struct pci_dev *pci_root = pci_get_bus_and_slot (0, 0);
- pci_write_config_dword (pci_root, 0xD4, value);
- pci_write_config_dword (pci_root, 0xD0, mcr);
+ struct pci_dev *pci_root = pci_get_bus_and_slot(0, 0);
+ pci_write_config_dword(pci_root, 0xD4, value);
+ pci_write_config_dword(pci_root, 0xD0, mcr);
pci_dev_put(pci_root);
}
/* #define TRAP_SGX_PM_FAULT 1 */
#ifdef TRAP_SGX_PM_FAULT
-#define PSB_RSGX32(_offs) \
-({ \
- if (inl(dev_priv->apm_base + PSB_APM_STS) & 0x3) { \
- printk(KERN_ERR "access sgx when it's off!! (READ) %s, %d\n", \
- __FILE__, __LINE__); \
- mdelay(1000); \
- } \
- ioread32(dev_priv->sgx_reg + (_offs)); \
+#define PSB_RSGX32(_offs) \
+({ \
+ if (inl(dev_priv->apm_base + PSB_APM_STS) & 0x3) { \
+ printk(KERN_ERR \
+ "access sgx when it's off!! (READ) %s, %d\n", \
+ __FILE__, __LINE__); \
+ melay(1000); \
+ } \
+ ioread32(dev_priv->sgx_reg + (_offs)); \
})
#else
#define PSB_RSGX32(_offs) ioread32(dev_priv->sgx_reg + (_offs))
fb_screen_base = (char *)info->screen_base;
- /* If this is a GEM object then info->screen_base is the virtual
- kernel remapping of the object. FIXME: Review if this is
- suitable for our mmap work */
+ /*
+ * If this is a GEM object then info->screen_base is the virtual
+ * kernel remapping of the object. FIXME: Review if this is
+ * suitable for our mmap work
+ */
vma->vm_ops = &psbfb_vm_ops;
vma->vm_private_data = (void *)psbfb;
vma->vm_flags |= VM_RESERVED | VM_IO |
return 0;
}
-static int psbfb_ioctl(struct fb_info *info, unsigned int cmd, unsigned long arg)
+static int psbfb_ioctl(struct fb_info *info, unsigned int cmd,
+ unsigned long arg)
{
struct psb_fbdev *fbdev = info->par;
struct psb_framebuffer *psbfb = &fbdev->pfb;
* 0 on success or an error code if we fail.
*/
static int psb_framebuffer_init(struct drm_device *dev,
- struct psb_framebuffer *fb,
- struct drm_mode_fb_cmd *mode_cmd,
- struct gtt_range *gt)
+ struct psb_framebuffer *fb,
+ struct drm_mode_fb_cmd *mode_cmd,
+ struct gtt_range *gt)
{
- int ret;
-
- if (mode_cmd->pitch & 63)
- return -EINVAL;
- switch (mode_cmd->bpp) {
- case 8:
- case 16:
- case 24:
- case 32:
- break;
- default:
- return -EINVAL;
- }
- ret = drm_framebuffer_init(dev, &fb->base, &psb_fb_funcs);
- if (ret) {
- dev_err(dev->dev, "framebuffer init failed: %d\n", ret);
- return ret;
- }
- drm_helper_mode_fill_fb_struct(&fb->base, mode_cmd);
- fb->gtt = gt;
- return 0;
+ int ret;
+
+ if (mode_cmd->pitch & 63)
+ return -EINVAL;
+ switch (mode_cmd->bpp) {
+ case 8:
+ case 16:
+ case 24:
+ case 32:
+ break;
+ default:
+ return -EINVAL;
+ }
+ ret = drm_framebuffer_init(dev, &fb->base, &psb_fb_funcs);
+ if (ret) {
+ dev_err(dev->dev, "framebuffer init failed: %d\n", ret);
+ return ret;
+ }
+ drm_helper_mode_fill_fb_struct(&fb->base, mode_cmd);
+ fb->gtt = gt;
+ return 0;
}
-
+
/**
* psb_framebuffer_create - create a framebuffer backed by gt
* @dev: our DRM device
ret = psb_framebuffer_init(dev, fb, mode_cmd, gt);
if (ret) {
- kfree(fb);
- return ERR_PTR(ret);
- }
- return &fb->base;
+ kfree(fb);
+ return ERR_PTR(ret);
+ }
+ return &fb->base;
}
/**
* stolen memory or the system has no stolen memory we allocate a range
* and back it with a GEM object.
*
- * In this case the GEM object has no handle.
+ * In this case the GEM object has no handle.
*
* FIXME: console speed up - allocate twice the space if room and use
* hardware scrolling for acceleration.
/* Begin by trying to use stolen memory backing */
backing = psb_gtt_alloc_range(dev, aligned_size, "fb", 1);
if (backing) {
- if (drm_gem_private_object_init(dev, &backing->gem, aligned_size) == 0)
- return backing;
- psb_gtt_free_range(dev, backing);
- }
+ if (drm_gem_private_object_init(dev,
+ &backing->gem, aligned_size) == 0)
+ return backing;
+ psb_gtt_free_range(dev, backing);
+ }
/* Next try using GEM host memory */
backing = psb_gtt_alloc_range(dev, aligned_size, "fb(gem)", 0);
if (backing == NULL)
}
return backing;
}
-
+
/**
* psbfb_create - create a framebuffer
* @fbdev: the framebuffer device
/* No 24bit packed */
if (mode_cmd.bpp == 24)
- mode_cmd.bpp = 32;
+ mode_cmd.bpp = 32;
/* HW requires pitch to be 64 byte aligned */
mode_cmd.pitch = ALIGN(mode_cmd.width * ((mode_cmd.bpp + 7) / 8), 64);
/* Allocate the framebuffer in the GTT with stolen page backing */
backing = psbfb_alloc(dev, size);
if (backing == NULL)
- return -ENOMEM;
+ return -ENOMEM;
mutex_lock(&dev->struct_mutex);
if (ret)
goto out_unref;
- fb = &psbfb->base;
+ fb = &psbfb->base;
psbfb->fbdev = info;
fbdev->psb_fb_helper.fb = fb;
mutex_unlock(&dev->struct_mutex);
return 0;
out_unref:
- if (backing->stolen)
- psb_gtt_free_range(dev, backing);
- else {
- if (psbfb->vm_map)
- vm_unmap_ram(info->screen_base, backing->npage);
- drm_gem_object_unreference(&backing->gem);
- }
+ if (backing->stolen)
+ psb_gtt_free_range(dev, backing);
+ else {
+ if (psbfb->vm_map)
+ vm_unmap_ram(info->screen_base, backing->npage);
+ drm_gem_object_unreference(&backing->gem);
+ }
out_err1:
mutex_unlock(&dev->struct_mutex);
psb_gtt_free_range(dev, backing);
(struct drm_device *dev, struct drm_file *filp,
struct drm_mode_fb_cmd *cmd)
{
- struct gtt_range *r;
- struct drm_gem_object *obj;
+ struct gtt_range *r;
+ struct drm_gem_object *obj;
- /* Find the GEM object and thus the gtt range object that is
- to back this space */
+ /*
+ * Find the GEM object and thus the gtt range object that is
+ * to back this space
+ */
obj = drm_gem_object_lookup(dev, filp, cmd->handle);
if (obj == NULL)
- return ERR_PTR(-ENOENT);
+ return ERR_PTR(-ENOENT);
- /* Let the core code do all the work */
- r = container_of(obj, struct gtt_range, gem);
+ /* Let the core code do all the work */
+ r = container_of(obj, struct gtt_range, gem);
return psb_framebuffer_create(dev, cmd, r);
}
}
unregister_framebuffer(info);
if (info->cmap.len)
- fb_dealloc_cmap(&info->cmap);
+ fb_dealloc_cmap(&info->cmap);
framebuffer_release(info);
}
drm_fb_helper_fini(&fbdev->psb_fb_helper);
drm_framebuffer_cleanup(&psbfb->base);
-
+
if (psbfb->gtt) {
/* FIXME: this is a bit more inside knowledge than I'd like
but I don't see how to make a fake GEM object of the
psb_gtt_free_range(dev, psbfb->gtt);
else
drm_gem_object_unreference(&psbfb->gtt->gem);
- }
+ }
return 0;
}
struct drm_file *file_priv,
unsigned int *handle)
{
- struct psb_framebuffer *psbfb = to_psb_fb(fb);
- struct gtt_range *r = psbfb->gtt;
- return drm_gem_handle_create(file_priv, &r->gem, handle);
+ struct psb_framebuffer *psbfb = to_psb_fb(fb);
+ struct gtt_range *r = psbfb->gtt;
+ return drm_gem_handle_create(file_priv, &r->gem, handle);
}
/**
reset = 1;
if (reset)
- /*
- * Now force a sane response before we permit the DRM crc layer to
- * do stupid things like blank the display. Instead we reset this
- * framebuffer as if the user had forced a reset. We must do this
- * before the cleanup so that the DRM layer doesn't get a chance
- * to stick its oar in where it isn't wanted.
+ /*
+ * Now force a sane response before we permit the DRM CRTC
+ * layer to do stupid things like blank the display. Instead
+ * we reset this framebuffer as if the user had forced a reset.
+ * We must do this before the cleanup so that the DRM layer
+ * doesn't get a chance to stick its oar in where it isn't
+ * wanted.
*/
drm_fb_helper_restore_fbdev_mode(&fbdev->psb_fb_helper);
- /* Let DRM do its clean up */
+ /* Let DRM do its clean up */
drm_framebuffer_cleanup(fb);
/* We are no longer using the resource in GEM */
drm_gem_object_unreference_unlocked(&r->gem);
map = list->map;
map->type = _DRM_GEM;
map->size = obj->size;
- map->handle =obj;
+ map->handle = obj;
list->file_offset_node = drm_mm_search_free(&mm->offset_manager,
obj->size / PAGE_SIZE, 0, 0);
if (!list->file_offset_node) {
- dev_err(dev->dev, "failed to allocate offset for bo %d\n", obj->name);
+ dev_err(dev->dev, "failed to allocate offset for bo %d\n",
+ obj->name);
ret = -ENOSPC;
goto free_it;
}
if (!(dev->driver->driver_features & DRIVER_GEM))
return -ENODEV;
-
+
mutex_lock(&dev->struct_mutex);
/* GEM does all our handle to object mapping */
goto unlock;
}
/* What validation is needed here ? */
-
+
/* Make it mmapable */
if (!obj->map_list.map) {
ret = psb_gem_create_mmap_offset(obj);
size = roundup(size, PAGE_SIZE);
- /* Allocate our object - for now a direct gtt range which is not
+ /* Allocate our object - for now a direct gtt range which is not
stolen memory backed */
r = psb_gtt_alloc_range(dev, size, "gem", 0);
if (r == NULL) {
if (r->mmapping == 0) {
ret = psb_gtt_pin(r);
if (ret < 0) {
- dev_err(dev->dev, "gma500: pin failed: %d\n", ret);
- goto fail;
- }
+ dev_err(dev->dev, "gma500: pin failed: %d\n", ret);
+ goto fail;
+ }
r->mmapping = 1;
}
ret = vm_insert_pfn(vma, (unsigned long)vmf->virtual_address, pfn);
fail:
- mutex_unlock(&dev->struct_mutex);
+ mutex_unlock(&dev->struct_mutex);
switch (ret) {
case 0:
case -ERESTARTSYS:
* psb_gtt_entry - find the GTT entries for a gtt_range
* @dev: our DRM device
* @r: our GTT range
- *
+ *
* Given a gtt_range object return the GTT offset of the page table
* entries for this gtt_range
*/
}
/* Make sure all the entries are set before we return */
ioread32(gtt_slot - 1);
-
return 0;
}
}
mutex_unlock(&dev_priv->gtt_mutex);
}
-
+
/*
* GTT resource allocator - allocate and manage GTT address space
*/
/* The start of the GTT is the stolen pages */
start = r->start;
end = r->start + dev_priv->pg->stolen_size - 1;
- } else {
- /* The rest we will use for GEM backed objects */
- start = r->start + dev_priv->pg->stolen_size;
- end = r->end;
- }
+ } else {
+ /* The rest we will use for GEM backed objects */
+ start = r->start + dev_priv->pg->stolen_size;
+ end = r->end;
+ }
gt = kzalloc(sizeof(struct gtt_range), GFP_KERNEL);
if (gt == NULL)
* @dev: our DRM device
* @gt: a mapping created with psb_gtt_alloc_range
*
- * Release a resource that was allocated with psb_gtt_alloc_range. If the object
- * has been pinned by mmap users we clean this up here currently.
+ * Release a resource that was allocated with psb_gtt_alloc_range. If the
+ * object has been pinned by mmap users we clean this up here currently.
*/
void psb_gtt_free_range(struct drm_device *dev, struct gtt_range *gt)
{
if (pg == NULL)
return -ENOMEM;
- /* Enable the GTT */
+ /* Enable the GTT */
pci_read_config_word(dev->pdev, PSB_GMCH_CTRL, &dev_priv->gmch_ctrl);
pci_write_config_word(dev->pdev, PSB_GMCH_CTRL,
dev_priv->gmch_ctrl | _PSB_GMCH_ENABLED);
pg->gtt_phys_start = dev_priv->pge_ctl & PAGE_MASK;
pg->gatt_start = pci_resource_start(dev->pdev, PSB_GATT_RESOURCE);
- /*
+ /*
* FIXME: video mmu has hw bug to access 0x0D0000000,
* then make gatt start at 0x0e000,0000
*/
pg->mmu_gatt_start = 0xE0000000;
pg->gtt_start = pci_resource_start(dev->pdev, PSB_GTT_RESOURCE);
- gtt_pages = pci_resource_len(dev->pdev, PSB_GTT_RESOURCE) >> PAGE_SHIFT;
- pg->gatt_pages = pci_resource_len(dev->pdev, PSB_GATT_RESOURCE) >> PAGE_SHIFT;
+ gtt_pages = pci_resource_len(dev->pdev, PSB_GTT_RESOURCE)
+ >> PAGE_SHIFT;
+ pg->gatt_pages = pci_resource_len(dev->pdev, PSB_GATT_RESOURCE)
+ >> PAGE_SHIFT;
pci_read_config_dword(dev->pdev, PSB_BSM, &dev_priv->stolen_base);
- vram_stolen_size = pg->gtt_phys_start - dev_priv->stolen_base - PAGE_SIZE;
+ vram_stolen_size = pg->gtt_phys_start - dev_priv->stolen_base
+ - PAGE_SIZE;
stolen_size = vram_stolen_size;
/*
* Map the GTT and the stolen memory area
*/
- dev_priv->gtt_map = ioremap_nocache(pg->gtt_phys_start, gtt_pages << PAGE_SHIFT);
+ dev_priv->gtt_map = ioremap_nocache(pg->gtt_phys_start,
+ gtt_pages << PAGE_SHIFT);
if (!dev_priv->gtt_map) {
dev_err(dev->dev, "Failure to map gtt.\n");
ret = -ENOMEM;
dspcntr |= DISPPLANE_32BPP_NO_ALPHA;
break;
default:
- dev_err(dev->dev, "Unknown color depth\n");
+ dev_err(dev->dev, "Unknown color depth\n");
ret = -EINVAL;
psb_gtt_unpin(psbfb->gtt);
goto psb_intel_pipe_set_base_exit;
/* No scan out no play */
if (crtc->fb == NULL) {
- crtc_funcs->mode_set_base(crtc, x, y, old_fb);
- return 0;
- }
+ crtc_funcs->mode_set_base(crtc, x, y, old_fb);
+ return 0;
+ }
list_for_each_entry(connector, &mode_config->connector_list, head) {
struct psb_intel_output *psb_intel_output =
u32 lvds = REG_READ(LVDS);
lvds &= ~LVDS_PIPEB_SELECT;
- if (pipe == 1)
- lvds |= LVDS_PIPEB_SELECT;
+ if (pipe == 1)
+ lvds |= LVDS_PIPEB_SELECT;
lvds |= LVDS_PORT_EN | LVDS_A0A2_CLKA_POWER_UP;
/* Set the B0-B3 data pairs corresponding to
u8 driver_ver[16];
u32 mboxes;
u8 reserved[164];
-} __attribute__((packed));
+} __packed;
struct opregion_apci {
/*FIXME: add it later*/
-} __attribute__((packed));
+} __packed;
struct opregion_swsci {
/*FIXME: add it later*/
-} __attribute__((packed));
+} __packed;
struct opregion_acpi {
/*FIXME: add it later*/
-} __attribute__((packed));
+} __packed;
int psb_intel_opregion_init(struct drm_device *dev)
{
*
* The actual value is this field multiplied by two.
*/
-#define BACKLIGHT_MODULATION_FREQ_MASK (0x7fff << 17)
-#define BLM_LEGACY_MODE (1 << 16)
+#define BACKLIGHT_MODULATION_FREQ_MASK (0x7fff << 17)
+#define BLM_LEGACY_MODE (1 << 16)
/*
* This is the number of cycles out of the backlight modulation cycle for which
* the backlight is on.
* This field must be no greater than the number of cycles in the complete
* backlight modulation cycle.
*/
-#define BACKLIGHT_DUTY_CYCLE_SHIFT (0)
-#define BACKLIGHT_DUTY_CYCLE_MASK (0xffff)
+#define BACKLIGHT_DUTY_CYCLE_SHIFT (0)
+#define BACKLIGHT_DUTY_CYCLE_MASK (0xffff)
#define I915_GCFGC 0xf0
-#define I915_LOW_FREQUENCY_ENABLE (1 << 7)
-#define I915_DISPLAY_CLOCK_190_200_MHZ (0 << 4)
-#define I915_DISPLAY_CLOCK_333_MHZ (4 << 4)
-#define I915_DISPLAY_CLOCK_MASK (7 << 4)
+#define I915_LOW_FREQUENCY_ENABLE (1 << 7)
+#define I915_DISPLAY_CLOCK_190_200_MHZ (0 << 4)
+#define I915_DISPLAY_CLOCK_333_MHZ (4 << 4)
+#define I915_DISPLAY_CLOCK_MASK (7 << 4)
#define I855_HPLLCC 0xc0
-#define I855_CLOCK_CONTROL_MASK (3 << 0)
-#define I855_CLOCK_133_200 (0 << 0)
-#define I855_CLOCK_100_200 (1 << 0)
-#define I855_CLOCK_100_133 (2 << 0)
-#define I855_CLOCK_166_250 (3 << 0)
+#define I855_CLOCK_CONTROL_MASK (3 << 0)
+#define I855_CLOCK_133_200 (0 << 0)
+#define I855_CLOCK_100_200 (1 << 0)
+#define I855_CLOCK_100_133 (2 << 0)
+#define I855_CLOCK_166_250 (3 << 0)
/* I830 CRTC registers */
-#define HTOTAL_A 0x60000
-#define HBLANK_A 0x60004
-#define HSYNC_A 0x60008
-#define VTOTAL_A 0x6000c
-#define VBLANK_A 0x60010
-#define VSYNC_A 0x60014
-#define PIPEASRC 0x6001c
-#define BCLRPAT_A 0x60020
-#define VSYNCSHIFT_A 0x60028
-
-#define HTOTAL_B 0x61000
-#define HBLANK_B 0x61004
-#define HSYNC_B 0x61008
-#define VTOTAL_B 0x6100c
-#define VBLANK_B 0x61010
-#define VSYNC_B 0x61014
-#define PIPEBSRC 0x6101c
-#define BCLRPAT_B 0x61020
-#define VSYNCSHIFT_B 0x61028
-
-#define HTOTAL_C 0x62000
-#define HBLANK_C 0x62004
-#define HSYNC_C 0x62008
-#define VTOTAL_C 0x6200c
-#define VBLANK_C 0x62010
-#define VSYNC_C 0x62014
-#define PIPECSRC 0x6201c
-#define BCLRPAT_C 0x62020
-#define VSYNCSHIFT_C 0x62028
-
-#define PP_STATUS 0x61200
-# define PP_ON (1 << 31)
+#define HTOTAL_A 0x60000
+#define HBLANK_A 0x60004
+#define HSYNC_A 0x60008
+#define VTOTAL_A 0x6000c
+#define VBLANK_A 0x60010
+#define VSYNC_A 0x60014
+#define PIPEASRC 0x6001c
+#define BCLRPAT_A 0x60020
+#define VSYNCSHIFT_A 0x60028
+
+#define HTOTAL_B 0x61000
+#define HBLANK_B 0x61004
+#define HSYNC_B 0x61008
+#define VTOTAL_B 0x6100c
+#define VBLANK_B 0x61010
+#define VSYNC_B 0x61014
+#define PIPEBSRC 0x6101c
+#define BCLRPAT_B 0x61020
+#define VSYNCSHIFT_B 0x61028
+
+#define HTOTAL_C 0x62000
+#define HBLANK_C 0x62004
+#define HSYNC_C 0x62008
+#define VTOTAL_C 0x6200c
+#define VBLANK_C 0x62010
+#define VSYNC_C 0x62014
+#define PIPECSRC 0x6201c
+#define BCLRPAT_C 0x62020
+#define VSYNCSHIFT_C 0x62028
+
+#define PP_STATUS 0x61200
+# define PP_ON (1 << 31)
/*
* Indicates that all dependencies of the panel are on:
*
* - pipe enabled
* - LVDS/DVOB/DVOC on
*/
-# define PP_READY (1 << 30)
-# define PP_SEQUENCE_NONE (0 << 28)
-# define PP_SEQUENCE_ON (1 << 28)
-# define PP_SEQUENCE_OFF (2 << 28)
-# define PP_SEQUENCE_MASK 0x30000000
-#define PP_CONTROL 0x61204
-# define POWER_TARGET_ON (1 << 0)
-
-#define LVDSPP_ON 0x61208
-#define LVDSPP_OFF 0x6120c
-#define PP_CYCLE 0x61210
-
-#define PFIT_CONTROL 0x61230
-# define PFIT_ENABLE (1 << 31)
-# define PFIT_PIPE_MASK (3 << 29)
-# define PFIT_PIPE_SHIFT 29
-# define PFIT_SCALING_MODE_PILLARBOX (1 << 27)
-# define PFIT_SCALING_MODE_LETTERBOX (3 << 26)
-# define VERT_INTERP_DISABLE (0 << 10)
-# define VERT_INTERP_BILINEAR (1 << 10)
-# define VERT_INTERP_MASK (3 << 10)
-# define VERT_AUTO_SCALE (1 << 9)
-# define HORIZ_INTERP_DISABLE (0 << 6)
-# define HORIZ_INTERP_BILINEAR (1 << 6)
-# define HORIZ_INTERP_MASK (3 << 6)
-# define HORIZ_AUTO_SCALE (1 << 5)
-# define PANEL_8TO6_DITHER_ENABLE (1 << 3)
-
-#define PFIT_PGM_RATIOS 0x61234
-# define PFIT_VERT_SCALE_MASK 0xfff00000
-# define PFIT_HORIZ_SCALE_MASK 0x0000fff0
+#define PP_READY (1 << 30)
+#define PP_SEQUENCE_NONE (0 << 28)
+#define PP_SEQUENCE_ON (1 << 28)
+#define PP_SEQUENCE_OFF (2 << 28)
+#define PP_SEQUENCE_MASK 0x30000000
+#define PP_CONTROL 0x61204
+#define POWER_TARGET_ON (1 << 0)
+
+#define LVDSPP_ON 0x61208
+#define LVDSPP_OFF 0x6120c
+#define PP_CYCLE 0x61210
+
+#define PFIT_CONTROL 0x61230
+#define PFIT_ENABLE (1 << 31)
+#define PFIT_PIPE_MASK (3 << 29)
+#define PFIT_PIPE_SHIFT 29
+#define PFIT_SCALING_MODE_PILLARBOX (1 << 27)
+#define PFIT_SCALING_MODE_LETTERBOX (3 << 26)
+#define VERT_INTERP_DISABLE (0 << 10)
+#define VERT_INTERP_BILINEAR (1 << 10)
+#define VERT_INTERP_MASK (3 << 10)
+#define VERT_AUTO_SCALE (1 << 9)
+#define HORIZ_INTERP_DISABLE (0 << 6)
+#define HORIZ_INTERP_BILINEAR (1 << 6)
+#define HORIZ_INTERP_MASK (3 << 6)
+#define HORIZ_AUTO_SCALE (1 << 5)
+#define PANEL_8TO6_DITHER_ENABLE (1 << 3)
+
+#define PFIT_PGM_RATIOS 0x61234
+#define PFIT_VERT_SCALE_MASK 0xfff00000
+#define PFIT_HORIZ_SCALE_MASK 0x0000fff0
#define PFIT_AUTO_RATIOS 0x61238
-
-#define DPLL_A 0x06014
-#define DPLL_B 0x06018
-# define DPLL_VCO_ENABLE (1 << 31)
-# define DPLL_DVO_HIGH_SPEED (1 << 30)
-# define DPLL_SYNCLOCK_ENABLE (1 << 29)
-# define DPLL_VGA_MODE_DIS (1 << 28)
-# define DPLLB_MODE_DAC_SERIAL (1 << 26) /* i915 */
-# define DPLLB_MODE_LVDS (2 << 26) /* i915 */
-# define DPLL_MODE_MASK (3 << 26)
-# define DPLL_DAC_SERIAL_P2_CLOCK_DIV_10 (0 << 24) /* i915 */
-# define DPLL_DAC_SERIAL_P2_CLOCK_DIV_5 (1 << 24) /* i915 */
-# define DPLLB_LVDS_P2_CLOCK_DIV_14 (0 << 24) /* i915 */
-# define DPLLB_LVDS_P2_CLOCK_DIV_7 (1 << 24) /* i915 */
-# define DPLL_P2_CLOCK_DIV_MASK 0x03000000 /* i915 */
-# define DPLL_FPA01_P1_POST_DIV_MASK 0x00ff0000 /* i915 */
+#define DPLL_A 0x06014
+#define DPLL_B 0x06018
+#define DPLL_VCO_ENABLE (1 << 31)
+#define DPLL_DVO_HIGH_SPEED (1 << 30)
+#define DPLL_SYNCLOCK_ENABLE (1 << 29)
+#define DPLL_VGA_MODE_DIS (1 << 28)
+#define DPLLB_MODE_DAC_SERIAL (1 << 26) /* i915 */
+#define DPLLB_MODE_LVDS (2 << 26) /* i915 */
+#define DPLL_MODE_MASK (3 << 26)
+#define DPLL_DAC_SERIAL_P2_CLOCK_DIV_10 (0 << 24) /* i915 */
+#define DPLL_DAC_SERIAL_P2_CLOCK_DIV_5 (1 << 24) /* i915 */
+#define DPLLB_LVDS_P2_CLOCK_DIV_14 (0 << 24) /* i915 */
+#define DPLLB_LVDS_P2_CLOCK_DIV_7 (1 << 24) /* i915 */
+#define DPLL_P2_CLOCK_DIV_MASK 0x03000000 /* i915 */
+#define DPLL_FPA01_P1_POST_DIV_MASK 0x00ff0000 /* i915 */
/*
* The i830 generation, in DAC/serial mode, defines p1 as two plus this
* bitfield, or just 2 if PLL_P1_DIVIDE_BY_TWO is set.
* The i830 generation, in LVDS mode, defines P1 as the bit number set within
* this field (only one bit may be set).
*/
-# define DPLL_FPA01_P1_POST_DIV_MASK_I830_LVDS 0x003f0000
-# define DPLL_FPA01_P1_POST_DIV_SHIFT 16
-# define PLL_P2_DIVIDE_BY_4 (1 << 23) /* i830, required
+#define DPLL_FPA01_P1_POST_DIV_MASK_I830_LVDS 0x003f0000
+#define DPLL_FPA01_P1_POST_DIV_SHIFT 16
+#define PLL_P2_DIVIDE_BY_4 (1 << 23) /* i830, required
* in DVO non-gang */
-# define PLL_P1_DIVIDE_BY_TWO (1 << 21) /* i830 */
-# define PLL_REF_INPUT_DREFCLK (0 << 13)
-# define PLL_REF_INPUT_TVCLKINA (1 << 13) /* i830 */
-# define PLL_REF_INPUT_TVCLKINBC (2 << 13) /* SDVO
+# define PLL_P1_DIVIDE_BY_TWO (1 << 21) /* i830 */
+#define PLL_REF_INPUT_DREFCLK (0 << 13)
+#define PLL_REF_INPUT_TVCLKINA (1 << 13) /* i830 */
+#define PLL_REF_INPUT_TVCLKINBC (2 << 13) /* SDVO
* TVCLKIN */
-# define PLLB_REF_INPUT_SPREADSPECTRUMIN (3 << 13)
-# define PLL_REF_INPUT_MASK (3 << 13)
-# define PLL_LOAD_PULSE_PHASE_SHIFT 9
+#define PLLB_REF_INPUT_SPREADSPECTRUMIN (3 << 13)
+#define PLL_REF_INPUT_MASK (3 << 13)
+#define PLL_LOAD_PULSE_PHASE_SHIFT 9
/*
* Parallel to Serial Load Pulse phase selection.
* Selects the phase for the 10X DPLL clock for the PCIe
* digital display port. The range is 4 to 13; 10 or more
* is just a flip delay. The default is 6
*/
-# define PLL_LOAD_PULSE_PHASE_MASK (0xf << PLL_LOAD_PULSE_PHASE_SHIFT)
-# define DISPLAY_RATE_SELECT_FPA1 (1 << 8)
+#define PLL_LOAD_PULSE_PHASE_MASK (0xf << PLL_LOAD_PULSE_PHASE_SHIFT)
+#define DISPLAY_RATE_SELECT_FPA1 (1 << 8)
/*
* SDVO multiplier for 945G/GM. Not used on 965.
*
* DPLL_MD_UDI_MULTIPLIER_MASK
*/
-# define SDVO_MULTIPLIER_MASK 0x000000ff
-# define SDVO_MULTIPLIER_SHIFT_HIRES 4
-# define SDVO_MULTIPLIER_SHIFT_VGA 0
+#define SDVO_MULTIPLIER_MASK 0x000000ff
+#define SDVO_MULTIPLIER_SHIFT_HIRES 4
+#define SDVO_MULTIPLIER_SHIFT_VGA 0
/*
* PLL_MD
*
* Value is pixels minus 1. Must be set to 1 pixel for SDVO.
*/
-# define DPLL_MD_UDI_DIVIDER_MASK 0x3f000000
-# define DPLL_MD_UDI_DIVIDER_SHIFT 24
+#define DPLL_MD_UDI_DIVIDER_MASK 0x3f000000
+#define DPLL_MD_UDI_DIVIDER_SHIFT 24
/* UDI pixel divider for VGA, same as DPLL_MD_UDI_DIVIDER_MASK. */
-# define DPLL_MD_VGA_UDI_DIVIDER_MASK 0x003f0000
-# define DPLL_MD_VGA_UDI_DIVIDER_SHIFT 16
+#define DPLL_MD_VGA_UDI_DIVIDER_MASK 0x003f0000
+#define DPLL_MD_VGA_UDI_DIVIDER_SHIFT 16
/*
* SDVO/UDI pixel multiplier.
*
* This register field has values of multiplication factor minus 1, with
* a maximum multiplier of 5 for SDVO.
*/
-# define DPLL_MD_UDI_MULTIPLIER_MASK 0x00003f00
-# define DPLL_MD_UDI_MULTIPLIER_SHIFT 8
+#define DPLL_MD_UDI_MULTIPLIER_MASK 0x00003f00
+#define DPLL_MD_UDI_MULTIPLIER_SHIFT 8
/*
* SDVO/UDI pixel multiplier for VGA, same as DPLL_MD_UDI_MULTIPLIER_MASK.
* This best be set to the default value (3) or the CRT won't work. No,
* I don't entirely understand what this does...
*/
-# define DPLL_MD_VGA_UDI_MULTIPLIER_MASK 0x0000003f
-# define DPLL_MD_VGA_UDI_MULTIPLIER_SHIFT 0
+#define DPLL_MD_VGA_UDI_MULTIPLIER_MASK 0x0000003f
+#define DPLL_MD_VGA_UDI_MULTIPLIER_SHIFT 0
#define DPLL_TEST 0x606c
-# define DPLLB_TEST_SDVO_DIV_1 (0 << 22)
-# define DPLLB_TEST_SDVO_DIV_2 (1 << 22)
-# define DPLLB_TEST_SDVO_DIV_4 (2 << 22)
-# define DPLLB_TEST_SDVO_DIV_MASK (3 << 22)
-# define DPLLB_TEST_N_BYPASS (1 << 19)
-# define DPLLB_TEST_M_BYPASS (1 << 18)
-# define DPLLB_INPUT_BUFFER_ENABLE (1 << 16)
-# define DPLLA_TEST_N_BYPASS (1 << 3)
-# define DPLLA_TEST_M_BYPASS (1 << 2)
-# define DPLLA_INPUT_BUFFER_ENABLE (1 << 0)
+#define DPLLB_TEST_SDVO_DIV_1 (0 << 22)
+#define DPLLB_TEST_SDVO_DIV_2 (1 << 22)
+#define DPLLB_TEST_SDVO_DIV_4 (2 << 22)
+#define DPLLB_TEST_SDVO_DIV_MASK (3 << 22)
+#define DPLLB_TEST_N_BYPASS (1 << 19)
+#define DPLLB_TEST_M_BYPASS (1 << 18)
+#define DPLLB_INPUT_BUFFER_ENABLE (1 << 16)
+#define DPLLA_TEST_N_BYPASS (1 << 3)
+#define DPLLA_TEST_M_BYPASS (1 << 2)
+#define DPLLA_INPUT_BUFFER_ENABLE (1 << 0)
#define ADPA 0x61100
-#define ADPA_DAC_ENABLE (1<<31)
-#define ADPA_DAC_DISABLE 0
-#define ADPA_PIPE_SELECT_MASK (1<<30)
-#define ADPA_PIPE_A_SELECT 0
-#define ADPA_PIPE_B_SELECT (1<<30)
-#define ADPA_USE_VGA_HVPOLARITY (1<<15)
-#define ADPA_SETS_HVPOLARITY 0
-#define ADPA_VSYNC_CNTL_DISABLE (1<<11)
-#define ADPA_VSYNC_CNTL_ENABLE 0
-#define ADPA_HSYNC_CNTL_DISABLE (1<<10)
-#define ADPA_HSYNC_CNTL_ENABLE 0
-#define ADPA_VSYNC_ACTIVE_HIGH (1<<4)
-#define ADPA_VSYNC_ACTIVE_LOW 0
-#define ADPA_HSYNC_ACTIVE_HIGH (1<<3)
-#define ADPA_HSYNC_ACTIVE_LOW 0
-
-#define FPA0 0x06040
-#define FPA1 0x06044
-#define FPB0 0x06048
-#define FPB1 0x0604c
-# define FP_N_DIV_MASK 0x003f0000
-# define FP_N_DIV_SHIFT 16
-# define FP_M1_DIV_MASK 0x00003f00
-# define FP_M1_DIV_SHIFT 8
-# define FP_M2_DIV_MASK 0x0000003f
-# define FP_M2_DIV_SHIFT 0
-
+#define ADPA_DAC_ENABLE (1 << 31)
+#define ADPA_DAC_DISABLE 0
+#define ADPA_PIPE_SELECT_MASK (1 << 30)
+#define ADPA_PIPE_A_SELECT 0
+#define ADPA_PIPE_B_SELECT (1 << 30)
+#define ADPA_USE_VGA_HVPOLARITY (1 << 15)
+#define ADPA_SETS_HVPOLARITY 0
+#define ADPA_VSYNC_CNTL_DISABLE (1 << 11)
+#define ADPA_VSYNC_CNTL_ENABLE 0
+#define ADPA_HSYNC_CNTL_DISABLE (1 << 10)
+#define ADPA_HSYNC_CNTL_ENABLE 0
+#define ADPA_VSYNC_ACTIVE_HIGH (1 << 4)
+#define ADPA_VSYNC_ACTIVE_LOW 0
+#define ADPA_HSYNC_ACTIVE_HIGH (1 << 3)
+#define ADPA_HSYNC_ACTIVE_LOW 0
+
+#define FPA0 0x06040
+#define FPA1 0x06044
+#define FPB0 0x06048
+#define FPB1 0x0604c
+#define FP_N_DIV_MASK 0x003f0000
+#define FP_N_DIV_SHIFT 16
+#define FP_M1_DIV_MASK 0x00003f00
+#define FP_M1_DIV_SHIFT 8
+#define FP_M2_DIV_MASK 0x0000003f
+#define FP_M2_DIV_SHIFT 0
#define PORT_HOTPLUG_EN 0x61110
-# define SDVOB_HOTPLUG_INT_EN (1 << 26)
-# define SDVOC_HOTPLUG_INT_EN (1 << 25)
-# define TV_HOTPLUG_INT_EN (1 << 18)
-# define CRT_HOTPLUG_INT_EN (1 << 9)
-# define CRT_HOTPLUG_FORCE_DETECT (1 << 3)
+#define SDVOB_HOTPLUG_INT_EN (1 << 26)
+#define SDVOC_HOTPLUG_INT_EN (1 << 25)
+#define TV_HOTPLUG_INT_EN (1 << 18)
+#define CRT_HOTPLUG_INT_EN (1 << 9)
+#define CRT_HOTPLUG_FORCE_DETECT (1 << 3)
#define PORT_HOTPLUG_STAT 0x61114
-# define CRT_HOTPLUG_INT_STATUS (1 << 11)
-# define TV_HOTPLUG_INT_STATUS (1 << 10)
-# define CRT_HOTPLUG_MONITOR_MASK (3 << 8)
-# define CRT_HOTPLUG_MONITOR_COLOR (3 << 8)
-# define CRT_HOTPLUG_MONITOR_MONO (2 << 8)
-# define CRT_HOTPLUG_MONITOR_NONE (0 << 8)
-# define SDVOC_HOTPLUG_INT_STATUS (1 << 7)
-# define SDVOB_HOTPLUG_INT_STATUS (1 << 6)
+#define CRT_HOTPLUG_INT_STATUS (1 << 11)
+#define TV_HOTPLUG_INT_STATUS (1 << 10)
+#define CRT_HOTPLUG_MONITOR_MASK (3 << 8)
+#define CRT_HOTPLUG_MONITOR_COLOR (3 << 8)
+#define CRT_HOTPLUG_MONITOR_MONO (2 << 8)
+#define CRT_HOTPLUG_MONITOR_NONE (0 << 8)
+#define SDVOC_HOTPLUG_INT_STATUS (1 << 7)
+#define SDVOB_HOTPLUG_INT_STATUS (1 << 6)
#define SDVOB 0x61140
#define SDVOC 0x61160
-#define SDVO_ENABLE (1 << 31)
-#define SDVO_PIPE_B_SELECT (1 << 30)
-#define SDVO_STALL_SELECT (1 << 29)
-#define SDVO_INTERRUPT_ENABLE (1 << 26)
+#define SDVO_ENABLE (1 << 31)
+#define SDVO_PIPE_B_SELECT (1 << 30)
+#define SDVO_STALL_SELECT (1 << 29)
+#define SDVO_INTERRUPT_ENABLE (1 << 26)
+
/**
* 915G/GM SDVO pixel multiplier.
*
*
* DPLL_MD_UDI_MULTIPLIER_MASK
*/
-#define SDVO_PORT_MULTIPLY_MASK (7 << 23)
-#define SDVO_PORT_MULTIPLY_SHIFT 23
-#define SDVO_PHASE_SELECT_MASK (15 << 19)
-#define SDVO_PHASE_SELECT_DEFAULT (6 << 19)
-#define SDVO_CLOCK_OUTPUT_INVERT (1 << 18)
-#define SDVOC_GANG_MODE (1 << 16)
-#define SDVO_BORDER_ENABLE (1 << 7)
-#define SDVOB_PCIE_CONCURRENCY (1 << 3)
-#define SDVO_DETECTED (1 << 2)
+#define SDVO_PORT_MULTIPLY_MASK (7 << 23)
+#define SDVO_PORT_MULTIPLY_SHIFT 23
+#define SDVO_PHASE_SELECT_MASK (15 << 19)
+#define SDVO_PHASE_SELECT_DEFAULT (6 << 19)
+#define SDVO_CLOCK_OUTPUT_INVERT (1 << 18)
+#define SDVOC_GANG_MODE (1 << 16)
+#define SDVO_BORDER_ENABLE (1 << 7)
+#define SDVOB_PCIE_CONCURRENCY (1 << 3)
+#define SDVO_DETECTED (1 << 2)
/* Bits to be preserved when writing */
#define SDVOB_PRESERVE_MASK ((1 << 17) | (1 << 16) | (1 << 14))
-#define SDVOC_PRESERVE_MASK (1 << 17)
+#define SDVOC_PRESERVE_MASK (1 << 17)
/*
* This register controls the LVDS output enable, pipe selection, and data
* Enables the LVDS port. This bit must be set before DPLLs are enabled, as
* the DPLL semantics change when the LVDS is assigned to that pipe.
*/
-# define LVDS_PORT_EN (1 << 31)
+#define LVDS_PORT_EN (1 << 31)
/* Selects pipe B for LVDS data. Must be set on pre-965. */
-# define LVDS_PIPEB_SELECT (1 << 30)
+#define LVDS_PIPEB_SELECT (1 << 30)
/* Turns on border drawing to allow centered display. */
-# define LVDS_BORDER_EN (1 << 15)
+#define LVDS_BORDER_EN (1 << 15)
/*
* Enables the A0-A2 data pairs and CLKA, containing 18 bits of color data per
* pixel.
*/
-# define LVDS_A0A2_CLKA_POWER_MASK (3 << 8)
-# define LVDS_A0A2_CLKA_POWER_DOWN (0 << 8)
-# define LVDS_A0A2_CLKA_POWER_UP (3 << 8)
+#define LVDS_A0A2_CLKA_POWER_MASK (3 << 8)
+#define LVDS_A0A2_CLKA_POWER_DOWN (0 << 8)
+#define LVDS_A0A2_CLKA_POWER_UP (3 << 8)
/*
* Controls the A3 data pair, which contains the additional LSBs for 24 bit
* mode. Only enabled if LVDS_A0A2_CLKA_POWER_UP also indicates it should be
* on.
*/
-# define LVDS_A3_POWER_MASK (3 << 6)
-# define LVDS_A3_POWER_DOWN (0 << 6)
-# define LVDS_A3_POWER_UP (3 << 6)
+#define LVDS_A3_POWER_MASK (3 << 6)
+#define LVDS_A3_POWER_DOWN (0 << 6)
+#define LVDS_A3_POWER_UP (3 << 6)
/*
* Controls the CLKB pair. This should only be set when LVDS_B0B3_POWER_UP
* is set.
*/
-# define LVDS_CLKB_POWER_MASK (3 << 4)
-# define LVDS_CLKB_POWER_DOWN (0 << 4)
-# define LVDS_CLKB_POWER_UP (3 << 4)
+#define LVDS_CLKB_POWER_MASK (3 << 4)
+#define LVDS_CLKB_POWER_DOWN (0 << 4)
+#define LVDS_CLKB_POWER_UP (3 << 4)
/*
* Controls the B0-B3 data pairs. This must be set to match the DPLL p2
* setting for whether we are in dual-channel mode. The B3 pair will
* additionally only be powered up when LVDS_A3_POWER_UP is set.
*/
-# define LVDS_B0B3_POWER_MASK (3 << 2)
-# define LVDS_B0B3_POWER_DOWN (0 << 2)
-# define LVDS_B0B3_POWER_UP (3 << 2)
-
-#define PIPEACONF 0x70008
-#define PIPEACONF_ENABLE (1<<31)
-#define PIPEACONF_DISABLE 0
-#define PIPEACONF_DOUBLE_WIDE (1<<30)
-#define PIPECONF_ACTIVE (1<<30)
-#define I965_PIPECONF_ACTIVE (1<<30)
-#define PIPECONF_DSIPLL_LOCK (1<<29)
-#define PIPEACONF_SINGLE_WIDE 0
-#define PIPEACONF_PIPE_UNLOCKED 0
-#define PIPEACONF_DSR (1<<26)
-#define PIPEACONF_PIPE_LOCKED (1<<25)
-#define PIPEACONF_PALETTE 0
-#define PIPECONF_FORCE_BORDER (1<<25)
-#define PIPEACONF_GAMMA (1<<24)
-#define PIPECONF_PROGRESSIVE (0 << 21)
+#define LVDS_B0B3_POWER_MASK (3 << 2)
+#define LVDS_B0B3_POWER_DOWN (0 << 2)
+#define LVDS_B0B3_POWER_UP (3 << 2)
+
+#define PIPEACONF 0x70008
+#define PIPEACONF_ENABLE (1 << 31)
+#define PIPEACONF_DISABLE 0
+#define PIPEACONF_DOUBLE_WIDE (1 << 30)
+#define PIPECONF_ACTIVE (1 << 30)
+#define I965_PIPECONF_ACTIVE (1 << 30)
+#define PIPECONF_DSIPLL_LOCK (1 << 29)
+#define PIPEACONF_SINGLE_WIDE 0
+#define PIPEACONF_PIPE_UNLOCKED 0
+#define PIPEACONF_DSR (1 << 26)
+#define PIPEACONF_PIPE_LOCKED (1 << 25)
+#define PIPEACONF_PALETTE 0
+#define PIPECONF_FORCE_BORDER (1 << 25)
+#define PIPEACONF_GAMMA (1 << 24)
+#define PIPECONF_PROGRESSIVE (0 << 21)
#define PIPECONF_INTERLACE_W_FIELD_INDICATION (6 << 21)
#define PIPECONF_INTERLACE_FIELD_0_ONLY (7 << 21)
-#define PIPECONF_PLANE_OFF (1<<19)
-#define PIPECONF_CURSOR_OFF (1<<18)
+#define PIPECONF_PLANE_OFF (1 << 19)
+#define PIPECONF_CURSOR_OFF (1 << 18)
+#define PIPEBCONF 0x71008
+#define PIPEBCONF_ENABLE (1 << 31)
+#define PIPEBCONF_DISABLE 0
+#define PIPEBCONF_DOUBLE_WIDE (1 << 30)
+#define PIPEBCONF_DISABLE 0
+#define PIPEBCONF_GAMMA (1 << 24)
+#define PIPEBCONF_PALETTE 0
-#define PIPEBCONF 0x71008
-#define PIPEBCONF_ENABLE (1<<31)
-#define PIPEBCONF_DISABLE 0
-#define PIPEBCONF_DOUBLE_WIDE (1<<30)
-#define PIPEBCONF_DISABLE 0
-#define PIPEBCONF_GAMMA (1<<24)
-#define PIPEBCONF_PALETTE 0
-
-#define PIPECCONF 0x72008
+#define PIPECCONF 0x72008
#define PIPEBGCMAXRED 0x71010
#define PIPEBGCMAXGREEN 0x71014
#define PIPEBGCMAXBLUE 0x71018
-#define PIPEASTAT 0x70024
+#define PIPEASTAT 0x70024
#define PIPEBSTAT 0x71024
#define PIPECSTAT 0x72024
-#define PIPE_VBLANK_INTERRUPT_STATUS (1UL<<1)
-#define PIPE_START_VBLANK_INTERRUPT_STATUS (1UL<<2)
-#define PIPE_VBLANK_CLEAR (1 << 1)
-#define PIPE_VBLANK_STATUS (1 << 1)
-#define PIPE_TE_STATUS (1UL<<6)
-#define PIPE_DPST_EVENT_STATUS (1UL<<7)
-#define PIPE_VSYNC_CLEAR (1UL<<9)
-#define PIPE_VSYNC_STATUS (1UL<<9)
-#define PIPE_HDMI_AUDIO_UNDERRUN_STATUS (1UL<<10)
-#define PIPE_HDMI_AUDIO_BUFFER_DONE_STATUS (1UL<<11)
-#define PIPE_VBLANK_INTERRUPT_ENABLE (1UL<<17)
-#define PIPE_START_VBLANK_INTERRUPT_ENABLE (1UL<<18)
-#define PIPE_TE_ENABLE (1UL<<22)
-#define PIPE_DPST_EVENT_ENABLE (1UL<<23)
-#define PIPE_VSYNC_ENABL (1UL<<25)
-#define PIPE_HDMI_AUDIO_UNDERRUN (1UL<<26)
-#define PIPE_HDMI_AUDIO_BUFFER_DONE (1UL<<27)
-#define PIPE_HDMI_AUDIO_INT_MASK (PIPE_HDMI_AUDIO_UNDERRUN | PIPE_HDMI_AUDIO_BUFFER_DONE)
+#define PIPE_VBLANK_INTERRUPT_STATUS (1UL << 1)
+#define PIPE_START_VBLANK_INTERRUPT_STATUS (1UL << 2)
+#define PIPE_VBLANK_CLEAR (1 << 1)
+#define PIPE_VBLANK_STATUS (1 << 1)
+#define PIPE_TE_STATUS (1UL << 6)
+#define PIPE_DPST_EVENT_STATUS (1UL << 7)
+#define PIPE_VSYNC_CLEAR (1UL << 9)
+#define PIPE_VSYNC_STATUS (1UL << 9)
+#define PIPE_HDMI_AUDIO_UNDERRUN_STATUS (1UL << 10)
+#define PIPE_HDMI_AUDIO_BUFFER_DONE_STATUS (1UL << 11)
+#define PIPE_VBLANK_INTERRUPT_ENABLE (1UL << 17)
+#define PIPE_START_VBLANK_INTERRUPT_ENABLE (1UL << 18)
+#define PIPE_TE_ENABLE (1UL << 22)
+#define PIPE_DPST_EVENT_ENABLE (1UL << 23)
+#define PIPE_VSYNC_ENABL (1UL << 25)
+#define PIPE_HDMI_AUDIO_UNDERRUN (1UL << 26)
+#define PIPE_HDMI_AUDIO_BUFFER_DONE (1UL << 27)
+#define PIPE_HDMI_AUDIO_INT_MASK (PIPE_HDMI_AUDIO_UNDERRUN | \
+ PIPE_HDMI_AUDIO_BUFFER_DONE)
#define PIPE_EVENT_MASK ((1 << 29)|(1 << 28)|(1 << 27)|(1 << 26)|(1 << 24)|(1 << 23)|(1 << 22)|(1 << 21)|(1 << 20)|(1 << 16))
#define PIPE_VBLANK_MASK ((1 << 25)|(1 << 24)|(1 << 18)|(1 << 17))
#define HISTOGRAM_INT_CONTROL 0x61268
#define HISTOGRAM_BIN_DATA 0X61264
#define HISTOGRAM_LOGIC_CONTROL 0x61260
#define PWM_CONTROL_LOGIC 0x61250
-#define PIPE_HOTPLUG_INTERRUPT_STATUS (1UL<<10)
-#define HISTOGRAM_INTERRUPT_ENABLE (1UL<<31)
-#define HISTOGRAM_LOGIC_ENABLE (1UL<<31)
-#define PWM_LOGIC_ENABLE (1UL<<31)
-#define PWM_PHASEIN_ENABLE (1UL<<25)
-#define PWM_PHASEIN_INT_ENABLE (1UL<<24)
-#define PWM_PHASEIN_VB_COUNT 0x00001f00
-#define PWM_PHASEIN_INC 0x0000001f
-#define HISTOGRAM_INT_CTRL_CLEAR (1UL<<30)
-#define DPST_YUV_LUMA_MODE 0
+#define PIPE_HOTPLUG_INTERRUPT_STATUS (1UL << 10)
+#define HISTOGRAM_INTERRUPT_ENABLE (1UL << 31)
+#define HISTOGRAM_LOGIC_ENABLE (1UL << 31)
+#define PWM_LOGIC_ENABLE (1UL << 31)
+#define PWM_PHASEIN_ENABLE (1UL << 25)
+#define PWM_PHASEIN_INT_ENABLE (1UL << 24)
+#define PWM_PHASEIN_VB_COUNT 0x00001f00
+#define PWM_PHASEIN_INC 0x0000001f
+#define HISTOGRAM_INT_CTRL_CLEAR (1UL << 30)
+#define DPST_YUV_LUMA_MODE 0
struct dpst_ie_histogram_control {
union {
#define PIPEBFRAMEPIXEL 0x71044
#define PIPECFRAMEHIGH 0x72040
#define PIPECFRAMEPIXEL 0x72044
-#define PIPE_FRAME_HIGH_MASK 0x0000ffff
-#define PIPE_FRAME_HIGH_SHIFT 0
-#define PIPE_FRAME_LOW_MASK 0xff000000
-#define PIPE_FRAME_LOW_SHIFT 24
-#define PIPE_PIXEL_MASK 0x00ffffff
-#define PIPE_PIXEL_SHIFT 0
+#define PIPE_FRAME_HIGH_MASK 0x0000ffff
+#define PIPE_FRAME_HIGH_SHIFT 0
+#define PIPE_FRAME_LOW_MASK 0xff000000
+#define PIPE_FRAME_LOW_SHIFT 24
+#define PIPE_PIXEL_MASK 0x00ffffff
+#define PIPE_PIXEL_SHIFT 0
#define DSPARB 0x70030
#define DSPFW1 0x70034
#define DSPACNTR 0x70180
#define DSPBCNTR 0x71180
#define DSPCCNTR 0x72180
-#define DISPLAY_PLANE_ENABLE (1<<31)
+#define DISPLAY_PLANE_ENABLE (1 << 31)
#define DISPLAY_PLANE_DISABLE 0
-#define DISPPLANE_GAMMA_ENABLE (1<<30)
+#define DISPPLANE_GAMMA_ENABLE (1 << 30)
#define DISPPLANE_GAMMA_DISABLE 0
-#define DISPPLANE_PIXFORMAT_MASK (0xf<<26)
-#define DISPPLANE_8BPP (0x2<<26)
-#define DISPPLANE_15_16BPP (0x4<<26)
-#define DISPPLANE_16BPP (0x5<<26)
-#define DISPPLANE_32BPP_NO_ALPHA (0x6<<26)
-#define DISPPLANE_32BPP (0x7<<26)
-#define DISPPLANE_STEREO_ENABLE (1<<25)
+#define DISPPLANE_PIXFORMAT_MASK (0xf << 26)
+#define DISPPLANE_8BPP (0x2 << 26)
+#define DISPPLANE_15_16BPP (0x4 << 26)
+#define DISPPLANE_16BPP (0x5 << 26)
+#define DISPPLANE_32BPP_NO_ALPHA (0x6 << 26)
+#define DISPPLANE_32BPP (0x7 << 26)
+#define DISPPLANE_STEREO_ENABLE (1 << 25)
#define DISPPLANE_STEREO_DISABLE 0
-#define DISPPLANE_SEL_PIPE_MASK (1<<24)
+#define DISPPLANE_SEL_PIPE_MASK (1 << 24)
#define DISPPLANE_SEL_PIPE_POS 24
#define DISPPLANE_SEL_PIPE_A 0
-#define DISPPLANE_SEL_PIPE_B (1<<24)
-#define DISPPLANE_SRC_KEY_ENABLE (1<<22)
+#define DISPPLANE_SEL_PIPE_B (1 << 24)
+#define DISPPLANE_SRC_KEY_ENABLE (1 << 22)
#define DISPPLANE_SRC_KEY_DISABLE 0
-#define DISPPLANE_LINE_DOUBLE (1<<20)
+#define DISPPLANE_LINE_DOUBLE (1 << 20)
#define DISPPLANE_NO_LINE_DOUBLE 0
#define DISPPLANE_STEREO_POLARITY_FIRST 0
-#define DISPPLANE_STEREO_POLARITY_SECOND (1<<18)
+#define DISPPLANE_STEREO_POLARITY_SECOND (1 << 18)
/* plane B only */
-#define DISPPLANE_ALPHA_TRANS_ENABLE (1<<15)
+#define DISPPLANE_ALPHA_TRANS_ENABLE (1 << 15)
#define DISPPLANE_ALPHA_TRANS_DISABLE 0
#define DISPPLANE_SPRITE_ABOVE_DISPLAYA 0
#define DISPPLANE_SPRITE_ABOVE_OVERLAY (1)
#define DSPCSURF 0x7219C
#define DSPCTILEOFF 0x721A4
-#define DSPCKEYMAXVAL 0x721A0
-#define DSPCKEYMINVAL 0x72194
-#define DSPCKEYMSK 0x72198
+#define DSPCKEYMAXVAL 0x721A0
+#define DSPCKEYMINVAL 0x72194
+#define DSPCKEYMSK 0x72198
#define VGACNTRL 0x71400
-# define VGA_DISP_DISABLE (1 << 31)
-# define VGA_2X_MODE (1 << 30)
-# define VGA_PIPE_B_SELECT (1 << 29)
+#define VGA_DISP_DISABLE (1 << 31)
+#define VGA_2X_MODE (1 << 30)
+#define VGA_PIPE_B_SELECT (1 << 29)
/*
* Overlay registers
*/
#define OV_C_OFFSET 0x08000
#define OV_OVADD 0x30000
-#define OV_DOVASTA 0x30008
-# define OV_PIPE_SELECT ((1 << 6)|(1 << 7))
-# define OV_PIPE_SELECT_POS 6
-# define OV_PIPE_A 0
-# define OV_PIPE_C 1
+#define OV_DOVASTA 0x30008
+# define OV_PIPE_SELECT ((1 << 6)|(1 << 7))
+# define OV_PIPE_SELECT_POS 6
+# define OV_PIPE_A 0
+# define OV_PIPE_C 1
#define OV_OGAMC5 0x30010
#define OV_OGAMC4 0x30014
#define OV_OGAMC3 0x30018
#define OV_OGAMC1 0x30020
#define OV_OGAMC0 0x30024
#define OVC_OVADD 0x38000
-#define OVC_DOVCSTA 0x38008
+#define OVC_DOVCSTA 0x38008
#define OVC_OGAMC5 0x38010
#define OVC_OGAMC4 0x38014
#define OVC_OGAMC3 0x38018
/* Cursor A & B regs */
#define CURACNTR 0x70080
-#define CURSOR_MODE_DISABLE 0x00
-#define CURSOR_MODE_64_32B_AX 0x07
-#define CURSOR_MODE_64_ARGB_AX ((1 << 5) | CURSOR_MODE_64_32B_AX)
-#define MCURSOR_GAMMA_ENABLE (1 << 26)
+#define CURSOR_MODE_DISABLE 0x00
+#define CURSOR_MODE_64_32B_AX 0x07
+#define CURSOR_MODE_64_ARGB_AX ((1 << 5) | CURSOR_MODE_64_32B_AX)
+#define MCURSOR_GAMMA_ENABLE (1 << 26)
#define CURABASE 0x70084
#define CURAPOS 0x70088
-#define CURSOR_POS_MASK 0x007FF
-#define CURSOR_POS_SIGN 0x8000
-#define CURSOR_X_SHIFT 0
-#define CURSOR_Y_SHIFT 16
+#define CURSOR_POS_MASK 0x007FF
+#define CURSOR_POS_SIGN 0x8000
+#define CURSOR_X_SHIFT 0
+#define CURSOR_Y_SHIFT 16
#define CURBCNTR 0x700c0
#define CURBBASE 0x700c4
#define CURBPOS 0x700c8
/*
* Interrupt Registers
*/
-#define IER 0x020a0
-#define IIR 0x020a4
-#define IMR 0x020a8
-#define ISR 0x020ac
+#define IER 0x020a0
+#define IIR 0x020a4
+#define IMR 0x020a8
+#define ISR 0x020ac
/*
* MOORESTOWN delta registers
*/
#define MRST_DPLL_A 0x0f014
#define MDFLD_DPLL_B 0x0f018
-#define MDFLD_INPUT_REF_SEL (1 << 14)
-#define MDFLD_VCO_SEL (1 << 16)
-#define DPLLA_MODE_LVDS (2 << 26) /* mrst */
-#define MDFLD_PLL_LATCHEN (1 << 28)
-#define MDFLD_PWR_GATE_EN (1 << 30)
-#define MDFLD_P1_MASK (0x1FF << 17)
+#define MDFLD_INPUT_REF_SEL (1 << 14)
+#define MDFLD_VCO_SEL (1 << 16)
+#define DPLLA_MODE_LVDS (2 << 26) /* mrst */
+#define MDFLD_PLL_LATCHEN (1 << 28)
+#define MDFLD_PWR_GATE_EN (1 << 30)
+#define MDFLD_P1_MASK (0x1FF << 17)
#define MRST_FPA0 0x0f040
#define MRST_FPA1 0x0f044
#define MDFLD_DPLL_DIV0 0x0f048
/*
* MEDFIELD HDMI registers
*/
-#define HDMIPHYMISCCTL 0x61134
-# define HDMI_PHY_POWER_DOWN 0x7f
-#define HDMIB_CONTROL 0x61140
-# define HDMIB_PORT_EN (1 << 31)
-# define HDMIB_PIPE_B_SELECT (1 << 30)
-# define HDMIB_NULL_PACKET (1 << 9)
-#define HDMIB_HDCP_PORT (1 << 5)
+#define HDMIPHYMISCCTL 0x61134
+#define HDMI_PHY_POWER_DOWN 0x7f
+#define HDMIB_CONTROL 0x61140
+#define HDMIB_PORT_EN (1 << 31)
+#define HDMIB_PIPE_B_SELECT (1 << 30)
+#define HDMIB_NULL_PACKET (1 << 9)
+#define HDMIB_HDCP_PORT (1 << 5)
/* #define LVDS 0x61180 */
-# define MRST_PANEL_8TO6_DITHER_ENABLE (1 << 25)
-# define MRST_PANEL_24_DOT_1_FORMAT (1 << 24)
-# define LVDS_A3_POWER_UP_0_OUTPUT (1 << 6)
+#define MRST_PANEL_8TO6_DITHER_ENABLE (1 << 25)
+#define MRST_PANEL_24_DOT_1_FORMAT (1 << 24)
+#define LVDS_A3_POWER_UP_0_OUTPUT (1 << 6)
#define MIPI 0x61190
#define MIPI_C 0x62190
-# define MIPI_PORT_EN (1 << 31)
+#define MIPI_PORT_EN (1 << 31)
/* Turns on border drawing to allow centered display. */
-# define SEL_FLOPPED_HSTX (1 << 23)
-# define PASS_FROM_SPHY_TO_AFE (1 << 16)
-# define MIPI_BORDER_EN (1 << 15)
-# define MIPIA_3LANE_MIPIC_1LANE 0x1
-# define MIPIA_2LANE_MIPIC_2LANE 0x2
-# define TE_TRIGGER_DSI_PROTOCOL (1 << 2)
-# define TE_TRIGGER_GPIO_PIN (1 << 3)
-#define MIPI_TE_COUNT 0x61194
+#define SEL_FLOPPED_HSTX (1 << 23)
+#define PASS_FROM_SPHY_TO_AFE (1 << 16)
+#define MIPI_BORDER_EN (1 << 15)
+#define MIPIA_3LANE_MIPIC_1LANE 0x1
+#define MIPIA_2LANE_MIPIC_2LANE 0x2
+#define TE_TRIGGER_DSI_PROTOCOL (1 << 2)
+#define TE_TRIGGER_GPIO_PIN (1 << 3)
+#define MIPI_TE_COUNT 0x61194
/* #define PP_CONTROL 0x61204 */
-# define POWER_DOWN_ON_RESET (1 << 1)
+#define POWER_DOWN_ON_RESET (1 << 1)
/* #define PFIT_CONTROL 0x61230 */
-# define PFIT_PIPE_SELECT (3 << 29)
-# define PFIT_PIPE_SELECT_SHIFT (29)
+#define PFIT_PIPE_SELECT (3 << 29)
+#define PFIT_PIPE_SELECT_SHIFT (29)
/* #define BLC_PWM_CTL 0x61254 */
-#define MRST_BACKLIGHT_MODULATION_FREQ_SHIFT (16)
-#define MRST_BACKLIGHT_MODULATION_FREQ_MASK (0xffff << 16)
+#define MRST_BACKLIGHT_MODULATION_FREQ_SHIFT (16)
+#define MRST_BACKLIGHT_MODULATION_FREQ_MASK (0xffff << 16)
/* #define PIPEACONF 0x70008 */
-#define PIPEACONF_PIPE_STATE (1<<30)
+#define PIPEACONF_PIPE_STATE (1 << 30)
/* #define DSPACNTR 0x70180 */
#define MRST_DSPABASE 0x7019c
/*
* MIPI IP registers
*/
-#define MIPIC_REG_OFFSET 0x800
-#define DEVICE_READY_REG 0xb000
-#define LP_OUTPUT_HOLD (1 << 16)
-#define EXIT_ULPS_DEV_READY 0x3
-#define LP_OUTPUT_HOLD_RELEASE 0x810000
-# define ENTERING_ULPS (2 << 1)
-# define EXITING_ULPS (1 << 1)
-# define ULPS_MASK (3 << 1)
-# define BUS_POSSESSION (1 << 3)
-#define INTR_STAT_REG 0xb004
-#define RX_SOT_ERROR (1 << 0)
-#define RX_SOT_SYNC_ERROR (1 << 1)
-#define RX_ESCAPE_MODE_ENTRY_ERROR (1 << 3)
-#define RX_LP_TX_SYNC_ERROR (1 << 4)
-#define RX_HS_RECEIVE_TIMEOUT_ERROR (1 << 5)
-#define RX_FALSE_CONTROL_ERROR (1 << 6)
-#define RX_ECC_SINGLE_BIT_ERROR (1 << 7)
-#define RX_ECC_MULTI_BIT_ERROR (1 << 8)
-#define RX_CHECKSUM_ERROR (1 << 9)
-#define RX_DSI_DATA_TYPE_NOT_RECOGNIZED (1 << 10)
-#define RX_DSI_VC_ID_INVALID (1 << 11)
-#define TX_FALSE_CONTROL_ERROR (1 << 12)
-#define TX_ECC_SINGLE_BIT_ERROR (1 << 13)
-#define TX_ECC_MULTI_BIT_ERROR (1 << 14)
-#define TX_CHECKSUM_ERROR (1 << 15)
-#define TX_DSI_DATA_TYPE_NOT_RECOGNIZED (1 << 16)
-#define TX_DSI_VC_ID_INVALID (1 << 17)
-#define HIGH_CONTENTION (1 << 18)
-#define LOW_CONTENTION (1 << 19)
-#define DPI_FIFO_UNDER_RUN (1 << 20)
-#define HS_TX_TIMEOUT (1 << 21)
-#define LP_RX_TIMEOUT (1 << 22)
-#define TURN_AROUND_ACK_TIMEOUT (1 << 23)
-#define ACK_WITH_NO_ERROR (1 << 24)
-#define HS_GENERIC_WR_FIFO_FULL (1 << 27)
-#define LP_GENERIC_WR_FIFO_FULL (1 << 28)
-#define SPL_PKT_SENT (1 << 30)
-#define INTR_EN_REG 0xb008
-#define DSI_FUNC_PRG_REG 0xb00c
-#define DPI_CHANNEL_NUMBER_POS 0x03
-#define DBI_CHANNEL_NUMBER_POS 0x05
-#define FMT_DPI_POS 0x07
-#define FMT_DBI_POS 0x0A
-#define DBI_DATA_WIDTH_POS 0x0D
+#define MIPIC_REG_OFFSET 0x800
+
+#define DEVICE_READY_REG 0xb000
+#define LP_OUTPUT_HOLD (1 << 16)
+#define EXIT_ULPS_DEV_READY 0x3
+#define LP_OUTPUT_HOLD_RELEASE 0x810000
+# define ENTERING_ULPS (2 << 1)
+# define EXITING_ULPS (1 << 1)
+# define ULPS_MASK (3 << 1)
+# define BUS_POSSESSION (1 << 3)
+#define INTR_STAT_REG 0xb004
+#define RX_SOT_ERROR (1 << 0)
+#define RX_SOT_SYNC_ERROR (1 << 1)
+#define RX_ESCAPE_MODE_ENTRY_ERROR (1 << 3)
+#define RX_LP_TX_SYNC_ERROR (1 << 4)
+#define RX_HS_RECEIVE_TIMEOUT_ERROR (1 << 5)
+#define RX_FALSE_CONTROL_ERROR (1 << 6)
+#define RX_ECC_SINGLE_BIT_ERROR (1 << 7)
+#define RX_ECC_MULTI_BIT_ERROR (1 << 8)
+#define RX_CHECKSUM_ERROR (1 << 9)
+#define RX_DSI_DATA_TYPE_NOT_RECOGNIZED (1 << 10)
+#define RX_DSI_VC_ID_INVALID (1 << 11)
+#define TX_FALSE_CONTROL_ERROR (1 << 12)
+#define TX_ECC_SINGLE_BIT_ERROR (1 << 13)
+#define TX_ECC_MULTI_BIT_ERROR (1 << 14)
+#define TX_CHECKSUM_ERROR (1 << 15)
+#define TX_DSI_DATA_TYPE_NOT_RECOGNIZED (1 << 16)
+#define TX_DSI_VC_ID_INVALID (1 << 17)
+#define HIGH_CONTENTION (1 << 18)
+#define LOW_CONTENTION (1 << 19)
+#define DPI_FIFO_UNDER_RUN (1 << 20)
+#define HS_TX_TIMEOUT (1 << 21)
+#define LP_RX_TIMEOUT (1 << 22)
+#define TURN_AROUND_ACK_TIMEOUT (1 << 23)
+#define ACK_WITH_NO_ERROR (1 << 24)
+#define HS_GENERIC_WR_FIFO_FULL (1 << 27)
+#define LP_GENERIC_WR_FIFO_FULL (1 << 28)
+#define SPL_PKT_SENT (1 << 30)
+#define INTR_EN_REG 0xb008
+#define DSI_FUNC_PRG_REG 0xb00c
+#define DPI_CHANNEL_NUMBER_POS 0x03
+#define DBI_CHANNEL_NUMBER_POS 0x05
+#define FMT_DPI_POS 0x07
+#define FMT_DBI_POS 0x0A
+#define DBI_DATA_WIDTH_POS 0x0D
+
/* DPI PIXEL FORMATS */
-#define RGB_565_FMT 0x01 /* RGB 565 FORMAT */
-#define RGB_666_FMT 0x02 /* RGB 666 FORMAT */
-#define LRGB_666_FMT 0x03 /* RGB LOOSELY PACKED
- * 666 FORMAT
- */
-#define RGB_888_FMT 0x04 /* RGB 888 FORMAT */
-#define VIRTUAL_CHANNEL_NUMBER_0 0x00 /* Virtual channel 0 */
-#define VIRTUAL_CHANNEL_NUMBER_1 0x01 /* Virtual channel 1 */
-#define VIRTUAL_CHANNEL_NUMBER_2 0x02 /* Virtual channel 2 */
-#define VIRTUAL_CHANNEL_NUMBER_3 0x03 /* Virtual channel 3 */
-#define DBI_NOT_SUPPORTED 0x00 /* command mode
- * is not supported
- */
-#define DBI_DATA_WIDTH_16BIT 0x01 /* 16 bit data */
+#define RGB_565_FMT 0x01 /* RGB 565 FORMAT */
+#define RGB_666_FMT 0x02 /* RGB 666 FORMAT */
+#define LRGB_666_FMT 0x03 /* RGB LOOSELY PACKED
+ * 666 FORMAT
+ */
+#define RGB_888_FMT 0x04 /* RGB 888 FORMAT */
+#define VIRTUAL_CHANNEL_NUMBER_0 0x00 /* Virtual channel 0 */
+#define VIRTUAL_CHANNEL_NUMBER_1 0x01 /* Virtual channel 1 */
+#define VIRTUAL_CHANNEL_NUMBER_2 0x02 /* Virtual channel 2 */
+#define VIRTUAL_CHANNEL_NUMBER_3 0x03 /* Virtual channel 3 */
+
+#define DBI_NOT_SUPPORTED 0x00 /* command mode
+ * is not supported
+ */
+#define DBI_DATA_WIDTH_16BIT 0x01 /* 16 bit data */
#define DBI_DATA_WIDTH_9BIT 0x02 /* 9 bit data */
#define DBI_DATA_WIDTH_8BIT 0x03 /* 8 bit data */
-#define DBI_DATA_WIDTH_OPT1 0x04 /* option 1 */
-#define DBI_DATA_WIDTH_OPT2 0x05 /* option 2 */
-#define HS_TX_TIMEOUT_REG 0xb010
-#define LP_RX_TIMEOUT_REG 0xb014
-#define TURN_AROUND_TIMEOUT_REG 0xb018
-#define DEVICE_RESET_REG 0xb01C
-#define DPI_RESOLUTION_REG 0xb020
-#define RES_V_POS 0x10
-#define DBI_RESOLUTION_REG 0xb024 /* Reserved for MDFLD */
-#define HORIZ_SYNC_PAD_COUNT_REG 0xb028
-#define HORIZ_BACK_PORCH_COUNT_REG 0xb02C
-#define HORIZ_FRONT_PORCH_COUNT_REG 0xb030
-#define HORIZ_ACTIVE_AREA_COUNT_REG 0xb034
-#define VERT_SYNC_PAD_COUNT_REG 0xb038
-#define VERT_BACK_PORCH_COUNT_REG 0xb03c
-#define VERT_FRONT_PORCH_COUNT_REG 0xb040
-#define HIGH_LOW_SWITCH_COUNT_REG 0xb044
-#define DPI_CONTROL_REG 0xb048
-#define DPI_SHUT_DOWN (1 << 0)
-#define DPI_TURN_ON (1 << 1)
-#define DPI_COLOR_MODE_ON (1 << 2)
-#define DPI_COLOR_MODE_OFF (1 << 3)
-#define DPI_BACK_LIGHT_ON (1 << 4)
-#define DPI_BACK_LIGHT_OFF (1 << 5)
-#define DPI_LP (1 << 6)
-#define DPI_DATA_REG 0xb04c
-#define DPI_BACK_LIGHT_ON_DATA 0x07
-#define DPI_BACK_LIGHT_OFF_DATA 0x17
-#define INIT_COUNT_REG 0xb050
-#define MAX_RET_PAK_REG 0xb054
-#define VIDEO_FMT_REG 0xb058
-#define COMPLETE_LAST_PCKT (1 << 2)
-#define EOT_DISABLE_REG 0xb05c
-#define ENABLE_CLOCK_STOPPING (1 << 1)
-#define LP_BYTECLK_REG 0xb060
-#define LP_GEN_DATA_REG 0xb064
-#define HS_GEN_DATA_REG 0xb068
-#define LP_GEN_CTRL_REG 0xb06C
-#define HS_GEN_CTRL_REG 0xb070
-#define DCS_CHANNEL_NUMBER_POS 0x06
-#define MCS_COMMANDS_POS 0x8
-#define WORD_COUNTS_POS 0x8
-#define MCS_PARAMETER_POS 0x10
-#define GEN_FIFO_STAT_REG 0xb074
-#define HS_DATA_FIFO_FULL (1 << 0)
-#define HS_DATA_FIFO_HALF_EMPTY (1 << 1)
-#define HS_DATA_FIFO_EMPTY (1 << 2)
-#define LP_DATA_FIFO_FULL (1 << 8)
-#define LP_DATA_FIFO_HALF_EMPTY (1 << 9)
-#define LP_DATA_FIFO_EMPTY (1 << 10)
-#define HS_CTRL_FIFO_FULL (1 << 16)
-#define HS_CTRL_FIFO_HALF_EMPTY (1 << 17)
-#define HS_CTRL_FIFO_EMPTY (1 << 18)
-#define LP_CTRL_FIFO_FULL (1 << 24)
-#define LP_CTRL_FIFO_HALF_EMPTY (1 << 25)
-#define LP_CTRL_FIFO_EMPTY (1 << 26)
-#define DBI_FIFO_EMPTY (1 << 27)
-#define DPI_FIFO_EMPTY (1 << 28)
-#define HS_LS_DBI_ENABLE_REG 0xb078
-#define TXCLKESC_REG 0xb07c
-#define DPHY_PARAM_REG 0xb080
-#define DBI_BW_CTRL_REG 0xb084
-#define CLK_LANE_SWT_REG 0xb088
+#define DBI_DATA_WIDTH_OPT1 0x04 /* option 1 */
+#define DBI_DATA_WIDTH_OPT2 0x05 /* option 2 */
+
+#define HS_TX_TIMEOUT_REG 0xb010
+#define LP_RX_TIMEOUT_REG 0xb014
+#define TURN_AROUND_TIMEOUT_REG 0xb018
+#define DEVICE_RESET_REG 0xb01C
+#define DPI_RESOLUTION_REG 0xb020
+#define RES_V_POS 0x10
+#define DBI_RESOLUTION_REG 0xb024 /* Reserved for MDFLD */
+#define HORIZ_SYNC_PAD_COUNT_REG 0xb028
+#define HORIZ_BACK_PORCH_COUNT_REG 0xb02C
+#define HORIZ_FRONT_PORCH_COUNT_REG 0xb030
+#define HORIZ_ACTIVE_AREA_COUNT_REG 0xb034
+#define VERT_SYNC_PAD_COUNT_REG 0xb038
+#define VERT_BACK_PORCH_COUNT_REG 0xb03c
+#define VERT_FRONT_PORCH_COUNT_REG 0xb040
+#define HIGH_LOW_SWITCH_COUNT_REG 0xb044
+#define DPI_CONTROL_REG 0xb048
+#define DPI_SHUT_DOWN (1 << 0)
+#define DPI_TURN_ON (1 << 1)
+#define DPI_COLOR_MODE_ON (1 << 2)
+#define DPI_COLOR_MODE_OFF (1 << 3)
+#define DPI_BACK_LIGHT_ON (1 << 4)
+#define DPI_BACK_LIGHT_OFF (1 << 5)
+#define DPI_LP (1 << 6)
+#define DPI_DATA_REG 0xb04c
+#define DPI_BACK_LIGHT_ON_DATA 0x07
+#define DPI_BACK_LIGHT_OFF_DATA 0x17
+#define INIT_COUNT_REG 0xb050
+#define MAX_RET_PAK_REG 0xb054
+#define VIDEO_FMT_REG 0xb058
+#define COMPLETE_LAST_PCKT (1 << 2)
+#define EOT_DISABLE_REG 0xb05c
+#define ENABLE_CLOCK_STOPPING (1 << 1)
+#define LP_BYTECLK_REG 0xb060
+#define LP_GEN_DATA_REG 0xb064
+#define HS_GEN_DATA_REG 0xb068
+#define LP_GEN_CTRL_REG 0xb06C
+#define HS_GEN_CTRL_REG 0xb070
+#define DCS_CHANNEL_NUMBER_POS 0x6
+#define MCS_COMMANDS_POS 0x8
+#define WORD_COUNTS_POS 0x8
+#define MCS_PARAMETER_POS 0x10
+#define GEN_FIFO_STAT_REG 0xb074
+#define HS_DATA_FIFO_FULL (1 << 0)
+#define HS_DATA_FIFO_HALF_EMPTY (1 << 1)
+#define HS_DATA_FIFO_EMPTY (1 << 2)
+#define LP_DATA_FIFO_FULL (1 << 8)
+#define LP_DATA_FIFO_HALF_EMPTY (1 << 9)
+#define LP_DATA_FIFO_EMPTY (1 << 10)
+#define HS_CTRL_FIFO_FULL (1 << 16)
+#define HS_CTRL_FIFO_HALF_EMPTY (1 << 17)
+#define HS_CTRL_FIFO_EMPTY (1 << 18)
+#define LP_CTRL_FIFO_FULL (1 << 24)
+#define LP_CTRL_FIFO_HALF_EMPTY (1 << 25)
+#define LP_CTRL_FIFO_EMPTY (1 << 26)
+#define DBI_FIFO_EMPTY (1 << 27)
+#define DPI_FIFO_EMPTY (1 << 28)
+#define HS_LS_DBI_ENABLE_REG 0xb078
+#define TXCLKESC_REG 0xb07c
+#define DPHY_PARAM_REG 0xb080
+#define DBI_BW_CTRL_REG 0xb084
+#define CLK_LANE_SWT_REG 0xb088
/*
* MIPI Adapter registers
*/
-#define MIPI_CONTROL_REG 0xb104
-#define MIPI_2X_CLOCK_BITS ((1 << 0) | (1 << 1))
-#define MIPI_DATA_ADDRESS_REG 0xb108
-#define MIPI_DATA_LENGTH_REG 0xb10C
-#define MIPI_COMMAND_ADDRESS_REG 0xb110
-#define MIPI_COMMAND_LENGTH_REG 0xb114
-#define MIPI_READ_DATA_RETURN_REG0 0xb118
-#define MIPI_READ_DATA_RETURN_REG1 0xb11C
-#define MIPI_READ_DATA_RETURN_REG2 0xb120
-#define MIPI_READ_DATA_RETURN_REG3 0xb124
-#define MIPI_READ_DATA_RETURN_REG4 0xb128
-#define MIPI_READ_DATA_RETURN_REG5 0xb12C
-#define MIPI_READ_DATA_RETURN_REG6 0xb130
-#define MIPI_READ_DATA_RETURN_REG7 0xb134
-#define MIPI_READ_DATA_VALID_REG 0xb138
+#define MIPI_CONTROL_REG 0xb104
+#define MIPI_2X_CLOCK_BITS ((1 << 0) | (1 << 1))
+#define MIPI_DATA_ADDRESS_REG 0xb108
+#define MIPI_DATA_LENGTH_REG 0xb10C
+#define MIPI_COMMAND_ADDRESS_REG 0xb110
+#define MIPI_COMMAND_LENGTH_REG 0xb114
+#define MIPI_READ_DATA_RETURN_REG0 0xb118
+#define MIPI_READ_DATA_RETURN_REG1 0xb11C
+#define MIPI_READ_DATA_RETURN_REG2 0xb120
+#define MIPI_READ_DATA_RETURN_REG3 0xb124
+#define MIPI_READ_DATA_RETURN_REG4 0xb128
+#define MIPI_READ_DATA_RETURN_REG5 0xb12C
+#define MIPI_READ_DATA_RETURN_REG6 0xb130
+#define MIPI_READ_DATA_RETURN_REG7 0xb134
+#define MIPI_READ_DATA_VALID_REG 0xb138
+
/* DBI COMMANDS */
-#define soft_reset 0x01
+#define soft_reset 0x01
/*
* The display module performs a software reset.
* Registers are written with their SW Reset default values.
*/
-#define get_power_mode 0x0a
+#define get_power_mode 0x0a
/*
* The display module returns the current power mode
*/
-#define get_address_mode 0x0b
+#define get_address_mode 0x0b
/*
* The display module returns the current status.
*/
-#define get_pixel_format 0x0c
+#define get_pixel_format 0x0c
/*
* This command gets the pixel format for the RGB image data
* used by the interface.
*/
-#define get_display_mode 0x0d
+#define get_display_mode 0x0d
/*
* The display module returns the Display Image Mode status.
*/
-#define get_signal_mode 0x0e
+#define get_signal_mode 0x0e
/*
* The display module returns the Display Signal Mode.
*/
-#define get_diagnostic_result 0x0f
+#define get_diagnostic_result 0x0f
/*
* The display module returns the self-diagnostic results following
* a Sleep Out command.
*/
-#define enter_sleep_mode 0x10
+#define enter_sleep_mode 0x10
/*
* This command causes the display module to enter the Sleep mode.
* In this mode, all unnecessary blocks inside the display module are
* disabled except interface communication. This is the lowest power
* mode the display module supports.
*/
-#define exit_sleep_mode 0x11
+#define exit_sleep_mode 0x11
/*
* This command causes the display module to exit Sleep mode.
* All blocks inside the display module are enabled.
*/
-#define enter_partial_mode 0x12
+#define enter_partial_mode 0x12
/*
* This command causes the display module to enter the Partial Display
* Mode. The Partial Display Mode window is described by the
* set_partial_area command.
*/
-#define enter_normal_mode 0x13
+#define enter_normal_mode 0x13
/*
* This command causes the display module to enter the Normal mode.
* Normal Mode is defined as Partial Display mode and Scroll mode are off
*/
-#define exit_invert_mode 0x20
+#define exit_invert_mode 0x20
/*
* This command causes the display module to stop inverting the image
* data on the display device. The frame memory contents remain unchanged.
* No status bits are changed.
*/
-#define enter_invert_mode 0x21
+#define enter_invert_mode 0x21
/*
* This command causes the display module to invert the image data only on
* the display device. The frame memory contents remain unchanged.
* No status bits are changed.
*/
-#define set_gamma_curve 0x26
+#define set_gamma_curve 0x26
/*
* This command selects the desired gamma curve for the display device.
* Four fixed gamma curves are defined in section DCS spec.
*/
-#define set_display_off 0x28
+#define set_display_off 0x28
/* ************************************************************************* *\
This command causes the display module to stop displaying the image data
on the display device. The frame memory contents remain unchanged.
No status bits are changed.
\* ************************************************************************* */
-#define set_display_on 0x29
+#define set_display_on 0x29
/* ************************************************************************* *\
This command causes the display module to start displaying the image data
on the display device. The frame memory contents remain unchanged.
No status bits are changed.
\* ************************************************************************* */
-#define set_column_address 0x2a
+#define set_column_address 0x2a
/*
* This command defines the column extent of the frame memory accessed by
* the hostprocessor with the read_memory_continue and
* write_memory_continue commands.
* No status bits are changed.
*/
-#define set_page_addr 0x2b
+#define set_page_addr 0x2b
/*
* This command defines the page extent of the frame memory accessed by
* the host processor with the write_memory_continue and
- * read_memory_continue command.
+ * read_memory_continue command.
* No status bits are changed.
*/
-#define write_mem_start 0x2c
+#define write_mem_start 0x2c
/*
* This command transfers image data from the host processor to the
- * display module s frame memory starting at the pixel location specified
+ * display modules frame memory starting at the pixel location specified
* by preceding set_column_address and set_page_address commands.
*/
-#define set_partial_area 0x30
+#define set_partial_area 0x30
/*
* This command defines the Partial Display mode s display area.
* There are two parameters associated with this command, the first
* defines the Start Row (SR) and the second the End Row (ER). SR and ER
* refer to the Frame Memory Line Pointer.
*/
-#define set_scroll_area 0x33
+#define set_scroll_area 0x33
/*
* This command defines the display modules Vertical Scrolling Area.
*/
-#define set_tear_off 0x34
+#define set_tear_off 0x34
/*
* This command turns off the display modules Tearing Effect output
* signal on the TE signal line.
*/
-#define set_tear_on 0x35
+#define set_tear_on 0x35
/*
* This command turns on the display modules Tearing Effect output signal
* on the TE signal line.
*/
-#define set_address_mode 0x36
+#define set_address_mode 0x36
/*
* This command sets the data order for transfers from the host processor
* to display modules frame memory,bits B[7:5] and B3, and from the
* display modules frame memory to the display device, bits B[2:0] and B4.
*/
-#define set_scroll_start 0x37
+#define set_scroll_start 0x37
/*
* This command sets the start of the vertical scrolling area in the frame
* memory. The vertical scrolling area is fully defined when this command
* line in the frame memory that is written to the display device as the
* first line of the vertical scroll area.
*/
-#define exit_idle_mode 0x38
+#define exit_idle_mode 0x38
/*
* This command causes the display module to exit Idle mode.
*/
-#define enter_idle_mode 0x39
+#define enter_idle_mode 0x39
/*
* This command causes the display module to enter Idle Mode.
* In Idle Mode, color expression is reduced. Colors are shown on the
* display device using the MSB of each of the R, G and B color
* components in the frame memory
*/
-#define set_pixel_format 0x3a
+#define set_pixel_format 0x3a
/*
* This command sets the pixel format for the RGB image data used by the
* interface.
* Bits D[2:0] DBI Pixel Format Definition
* Bits D7 and D3 are not used.
*/
- #define DCS_PIXEL_FORMAT_3bbp 0x1
- #define DCS_PIXEL_FORMAT_8bbp 0x2
- #define DCS_PIXEL_FORMAT_12bbp 0x3
- #define DCS_PIXEL_FORMAT_16bbp 0x5
- #define DCS_PIXEL_FORMAT_18bbp 0x6
- #define DCS_PIXEL_FORMAT_24bbp 0x7
-#define write_mem_cont 0x3c
+#define DCS_PIXEL_FORMAT_3bpp 0x1
+#define DCS_PIXEL_FORMAT_8bpp 0x2
+#define DCS_PIXEL_FORMAT_12bpp 0x3
+#define DCS_PIXEL_FORMAT_16bpp 0x5
+#define DCS_PIXEL_FORMAT_18bpp 0x6
+#define DCS_PIXEL_FORMAT_24bpp 0x7
+
+#define write_mem_cont 0x3c
+
/*
* This command transfers image data from the host processor to the
* display module's frame memory continuing from the pixel location
* following the previous write_memory_continue or write_memory_start
* command.
*/
-#define set_tear_scanline 0x44
+#define set_tear_scanline 0x44
/*
* This command turns on the display modules Tearing Effect output signal
* on the TE signal line when the display module reaches line N.
*/
-#define get_scanline 0x45
+#define get_scanline 0x45
/*
* The display module returns the current scanline, N, used to update the
* display device. The total number of scanlines on a display device is
#define GAMMA_AUTO (1 << 0)
/* DCS Interface Pixel Formats */
-#define DCS_PIXEL_FORMAT_3BPP 0x1
-#define DCS_PIXEL_FORMAT_8BPP 0x2
-#define DCS_PIXEL_FORMAT_12BPP 0x3
-#define DCS_PIXEL_FORMAT_16BPP 0x5
-#define DCS_PIXEL_FORMAT_18BPP 0x6
-#define DCS_PIXEL_FORMAT_24BPP 0x7
+#define DCS_PIXEL_FORMAT_3BPP 0x1
+#define DCS_PIXEL_FORMAT_8BPP 0x2
+#define DCS_PIXEL_FORMAT_12BPP 0x3
+#define DCS_PIXEL_FORMAT_16BPP 0x5
+#define DCS_PIXEL_FORMAT_18BPP 0x6
+#define DCS_PIXEL_FORMAT_24BPP 0x7
/* ONE PARAMETER READ DATA */
-#define addr_mode_data 0xfc
-#define diag_res_data 0x00
-#define disp_mode_data 0x23
-#define pxl_fmt_data 0x77
-#define pwr_mode_data 0x74
-#define sig_mode_data 0x00
+#define addr_mode_data 0xfc
+#define diag_res_data 0x00
+#define disp_mode_data 0x23
+#define pxl_fmt_data 0x77
+#define pwr_mode_data 0x74
+#define sig_mode_data 0x00
/* TWO PARAMETERS READ DATA */
-#define scanline_data1 0xff
-#define scanline_data2 0xff
+#define scanline_data1 0xff
+#define scanline_data2 0xff
#define NON_BURST_MODE_SYNC_PULSE 0x01 /* Non Burst Mode
* with Sync Pulse
*/
* with Sync events
*/
#define BURST_MODE 0x03 /* Burst Mode */
-#define DBI_COMMAND_BUFFER_SIZE 0x240 /* 0x32 */ /* 0x120 */ /* Allocate at least
+#define DBI_COMMAND_BUFFER_SIZE 0x240 /* 0x32 */ /* 0x120 */
+ /* Allocate at least
* 0x100 Byte with 32
* byte alignment
*/
* 0x100 Byte with 32
* byte alignment
*/
-#define DBI_CB_TIME_OUT 0xFFFF
-
-#define GEN_FB_TIME_OUT 2000
-#define ALIGNMENT_32BYTE_MASK (~((1 << 0)|(1 << 1)|(1 << 2)|(1 << 3)|(1 << 4)))
-#define SKU_83 0x01
-#define SKU_100 0x02
-#define SKU_100L 0x04
-#define SKU_BYPASS 0x08
+#define DBI_CB_TIME_OUT 0xFFFF
+
+#define GEN_FB_TIME_OUT 2000
+
+#define SKU_83 0x01
+#define SKU_100 0x02
+#define SKU_100L 0x04
+#define SKU_BYPASS 0x08
#endif
sizeof(sdvo_cmd_names) / sizeof(sdvo_cmd_names[0]);
i++) {
if (cmd == sdvo_cmd_names[i].cmd) {
- printk(KERN_CONT "(%s)", sdvo_cmd_names[i].name);
+ printk(KERN_CONT
+ "(%s)", sdvo_cmd_names[i].name);
break;
}
}
unsigned int stall_support:1;
unsigned int pad:1;
u16 output_flags;
-} __attribute__ ((packed));
+} __packed;
/** This matches the EDID DTD structure, more or less */
struct psb_intel_sdvo_dtd {
u8 v_sync_off_high;
u8 reserved;
} part2;
-} __attribute__ ((packed));
+} __packed;
struct psb_intel_sdvo_pixel_clock_range {
u16 min; /**< pixel clock, in 10kHz units */
u16 max; /**< pixel clock, in 10kHz units */
-} __attribute__ ((packed));
+} __packed;
struct psb_intel_sdvo_preferred_input_timing_args {
u16 clock;
u16 width;
u16 height;
-} __attribute__ ((packed));
+} __packed;
/* I2C registers for SDVO */
#define SDVO_I2C_ARG_0 0x07
unsigned int input0_trained:1;
unsigned int input1_trained:1;
unsigned int pad:6;
-} __attribute__ ((packed));
+} __packed;
/** Returns a struct psb_intel_sdvo_output_flags of active outputs. */
#define SDVO_CMD_GET_ACTIVE_OUTPUTS 0x04
u16 interrupt_status;
unsigned int ambient_light_interrupt:1;
unsigned int pad:7;
-} __attribute__ ((packed));
+} __packed;
/**
* Selects which input is affected by future input commands.
struct psb_intel_sdvo_set_target_input_args {
unsigned int target_1:1;
unsigned int pad:7;
-} __attribute__ ((packed));
+} __packed;
/**
* Takes a struct psb_intel_sdvo_output_flags of which outputs are targeted by
#ifndef _PSB_REG_H_
#define _PSB_REG_H_
-#define PSB_CR_CLKGATECTL 0x0000
-#define _PSB_C_CLKGATECTL_AUTO_MAN_REG (1 << 24)
-#define _PSB_C_CLKGATECTL_USE_CLKG_SHIFT (20)
-#define _PSB_C_CLKGATECTL_USE_CLKG_MASK (0x3 << 20)
-#define _PSB_C_CLKGATECTL_DPM_CLKG_SHIFT (16)
-#define _PSB_C_CLKGATECTL_DPM_CLKG_MASK (0x3 << 16)
-#define _PSB_C_CLKGATECTL_TA_CLKG_SHIFT (12)
-#define _PSB_C_CLKGATECTL_TA_CLKG_MASK (0x3 << 12)
-#define _PSB_C_CLKGATECTL_TSP_CLKG_SHIFT (8)
-#define _PSB_C_CLKGATECTL_TSP_CLKG_MASK (0x3 << 8)
-#define _PSB_C_CLKGATECTL_ISP_CLKG_SHIFT (4)
-#define _PSB_C_CLKGATECTL_ISP_CLKG_MASK (0x3 << 4)
-#define _PSB_C_CLKGATECTL_2D_CLKG_SHIFT (0)
-#define _PSB_C_CLKGATECTL_2D_CLKG_MASK (0x3 << 0)
-#define _PSB_C_CLKGATECTL_CLKG_ENABLED (0)
-#define _PSB_C_CLKGATECTL_CLKG_DISABLED (1)
-#define _PSB_C_CLKGATECTL_CLKG_AUTO (2)
-
-#define PSB_CR_CORE_ID 0x0010
-#define _PSB_CC_ID_ID_SHIFT (16)
-#define _PSB_CC_ID_ID_MASK (0xFFFF << 16)
-#define _PSB_CC_ID_CONFIG_SHIFT (0)
-#define _PSB_CC_ID_CONFIG_MASK (0xFFFF << 0)
-
-#define PSB_CR_CORE_REVISION 0x0014
-#define _PSB_CC_REVISION_DESIGNER_SHIFT (24)
-#define _PSB_CC_REVISION_DESIGNER_MASK (0xFF << 24)
-#define _PSB_CC_REVISION_MAJOR_SHIFT (16)
-#define _PSB_CC_REVISION_MAJOR_MASK (0xFF << 16)
-#define _PSB_CC_REVISION_MINOR_SHIFT (8)
-#define _PSB_CC_REVISION_MINOR_MASK (0xFF << 8)
-#define _PSB_CC_REVISION_MAINTENANCE_SHIFT (0)
-#define _PSB_CC_REVISION_MAINTENANCE_MASK (0xFF << 0)
-
-#define PSB_CR_DESIGNER_REV_FIELD1 0x0018
-
-#define PSB_CR_SOFT_RESET 0x0080
-#define _PSB_CS_RESET_TSP_RESET (1 << 6)
-#define _PSB_CS_RESET_ISP_RESET (1 << 5)
-#define _PSB_CS_RESET_USE_RESET (1 << 4)
-#define _PSB_CS_RESET_TA_RESET (1 << 3)
-#define _PSB_CS_RESET_DPM_RESET (1 << 2)
-#define _PSB_CS_RESET_TWOD_RESET (1 << 1)
-#define _PSB_CS_RESET_BIF_RESET (1 << 0)
-
-#define PSB_CR_DESIGNER_REV_FIELD2 0x001C
-
-#define PSB_CR_EVENT_HOST_ENABLE2 0x0110
-
-#define PSB_CR_EVENT_STATUS2 0x0118
-
-#define PSB_CR_EVENT_HOST_CLEAR2 0x0114
-#define _PSB_CE2_BIF_REQUESTER_FAULT (1 << 4)
-
-#define PSB_CR_EVENT_STATUS 0x012C
-
-#define PSB_CR_EVENT_HOST_ENABLE 0x0130
-
-#define PSB_CR_EVENT_HOST_CLEAR 0x0134
-#define _PSB_CE_MASTER_INTERRUPT (1 << 31)
-#define _PSB_CE_TA_DPM_FAULT (1 << 28)
-#define _PSB_CE_TWOD_COMPLETE (1 << 27)
-#define _PSB_CE_DPM_OUT_OF_MEMORY_ZLS (1 << 25)
-#define _PSB_CE_DPM_TA_MEM_FREE (1 << 24)
-#define _PSB_CE_PIXELBE_END_RENDER (1 << 18)
-#define _PSB_CE_SW_EVENT (1 << 14)
-#define _PSB_CE_TA_FINISHED (1 << 13)
-#define _PSB_CE_TA_TERMINATE (1 << 12)
-#define _PSB_CE_DPM_REACHED_MEM_THRESH (1 << 3)
-#define _PSB_CE_DPM_OUT_OF_MEMORY_GBL (1 << 2)
-#define _PSB_CE_DPM_OUT_OF_MEMORY_MT (1 << 1)
-#define _PSB_CE_DPM_3D_MEM_FREE (1 << 0)
-
-
-#define PSB_USE_OFFSET_MASK 0x0007FFFF
-#define PSB_USE_OFFSET_SIZE (PSB_USE_OFFSET_MASK + 1)
-#define PSB_CR_USE_CODE_BASE0 0x0A0C
-#define PSB_CR_USE_CODE_BASE1 0x0A10
-#define PSB_CR_USE_CODE_BASE2 0x0A14
-#define PSB_CR_USE_CODE_BASE3 0x0A18
-#define PSB_CR_USE_CODE_BASE4 0x0A1C
-#define PSB_CR_USE_CODE_BASE5 0x0A20
-#define PSB_CR_USE_CODE_BASE6 0x0A24
-#define PSB_CR_USE_CODE_BASE7 0x0A28
-#define PSB_CR_USE_CODE_BASE8 0x0A2C
-#define PSB_CR_USE_CODE_BASE9 0x0A30
-#define PSB_CR_USE_CODE_BASE10 0x0A34
-#define PSB_CR_USE_CODE_BASE11 0x0A38
-#define PSB_CR_USE_CODE_BASE12 0x0A3C
-#define PSB_CR_USE_CODE_BASE13 0x0A40
-#define PSB_CR_USE_CODE_BASE14 0x0A44
-#define PSB_CR_USE_CODE_BASE15 0x0A48
-#define PSB_CR_USE_CODE_BASE(_i) (0x0A0C + ((_i) << 2))
-#define _PSB_CUC_BASE_DM_SHIFT (25)
-#define _PSB_CUC_BASE_DM_MASK (0x3 << 25)
-#define _PSB_CUC_BASE_ADDR_SHIFT (0) /* 1024-bit aligned address? */
-#define _PSB_CUC_BASE_ADDR_ALIGNSHIFT (7)
-#define _PSB_CUC_BASE_ADDR_MASK (0x1FFFFFF << 0)
-#define _PSB_CUC_DM_VERTEX (0)
-#define _PSB_CUC_DM_PIXEL (1)
-#define _PSB_CUC_DM_RESERVED (2)
-#define _PSB_CUC_DM_EDM (3)
-
-#define PSB_CR_PDS_EXEC_BASE 0x0AB8
-#define _PSB_CR_PDS_EXEC_BASE_ADDR_SHIFT (20) /* 1MB aligned address */
-#define _PSB_CR_PDS_EXEC_BASE_ADDR_ALIGNSHIFT (20)
-
-#define PSB_CR_EVENT_KICKER 0x0AC4
-#define _PSB_CE_KICKER_ADDRESS_SHIFT (4) /* 128-bit aligned address */
-
-#define PSB_CR_EVENT_KICK 0x0AC8
-#define _PSB_CE_KICK_NOW (1 << 0)
-
-
-#define PSB_CR_BIF_DIR_LIST_BASE1 0x0C38
-
-#define PSB_CR_BIF_CTRL 0x0C00
-#define _PSB_CB_CTRL_CLEAR_FAULT (1 << 4)
-#define _PSB_CB_CTRL_INVALDC (1 << 3)
-#define _PSB_CB_CTRL_FLUSH (1 << 2)
-
-#define PSB_CR_BIF_INT_STAT 0x0C04
-
-#define PSB_CR_BIF_FAULT 0x0C08
-#define _PSB_CBI_STAT_PF_N_RW (1 << 14)
-#define _PSB_CBI_STAT_FAULT_SHIFT (0)
-#define _PSB_CBI_STAT_FAULT_MASK (0x3FFF << 0)
-#define _PSB_CBI_STAT_FAULT_CACHE (1 << 1)
-#define _PSB_CBI_STAT_FAULT_TA (1 << 2)
-#define _PSB_CBI_STAT_FAULT_VDM (1 << 3)
-#define _PSB_CBI_STAT_FAULT_2D (1 << 4)
-#define _PSB_CBI_STAT_FAULT_PBE (1 << 5)
-#define _PSB_CBI_STAT_FAULT_TSP (1 << 6)
-#define _PSB_CBI_STAT_FAULT_ISP (1 << 7)
-#define _PSB_CBI_STAT_FAULT_USSEPDS (1 << 8)
-#define _PSB_CBI_STAT_FAULT_HOST (1 << 9)
-
-#define PSB_CR_BIF_BANK0 0x0C78
-
-#define PSB_CR_BIF_BANK1 0x0C7C
-
-#define PSB_CR_BIF_DIR_LIST_BASE0 0x0C84
-
-#define PSB_CR_BIF_TWOD_REQ_BASE 0x0C88
-#define PSB_CR_BIF_3D_REQ_BASE 0x0CAC
-
-#define PSB_CR_2D_SOCIF 0x0E18
-#define _PSB_C2_SOCIF_FREESPACE_SHIFT (0)
-#define _PSB_C2_SOCIF_FREESPACE_MASK (0xFF << 0)
-#define _PSB_C2_SOCIF_EMPTY (0x80 << 0)
-
-#define PSB_CR_2D_BLIT_STATUS 0x0E04
-#define _PSB_C2B_STATUS_BUSY (1 << 24)
-#define _PSB_C2B_STATUS_COMPLETE_SHIFT (0)
-#define _PSB_C2B_STATUS_COMPLETE_MASK (0xFFFFFF << 0)
+#define PSB_CR_CLKGATECTL 0x0000
+#define _PSB_C_CLKGATECTL_AUTO_MAN_REG (1 << 24)
+#define _PSB_C_CLKGATECTL_USE_CLKG_SHIFT (20)
+#define _PSB_C_CLKGATECTL_USE_CLKG_MASK (0x3 << 20)
+#define _PSB_C_CLKGATECTL_DPM_CLKG_SHIFT (16)
+#define _PSB_C_CLKGATECTL_DPM_CLKG_MASK (0x3 << 16)
+#define _PSB_C_CLKGATECTL_TA_CLKG_SHIFT (12)
+#define _PSB_C_CLKGATECTL_TA_CLKG_MASK (0x3 << 12)
+#define _PSB_C_CLKGATECTL_TSP_CLKG_SHIFT (8)
+#define _PSB_C_CLKGATECTL_TSP_CLKG_MASK (0x3 << 8)
+#define _PSB_C_CLKGATECTL_ISP_CLKG_SHIFT (4)
+#define _PSB_C_CLKGATECTL_ISP_CLKG_MASK (0x3 << 4)
+#define _PSB_C_CLKGATECTL_2D_CLKG_SHIFT (0)
+#define _PSB_C_CLKGATECTL_2D_CLKG_MASK (0x3 << 0)
+#define _PSB_C_CLKGATECTL_CLKG_ENABLED (0)
+#define _PSB_C_CLKGATECTL_CLKG_DISABLED (1)
+#define _PSB_C_CLKGATECTL_CLKG_AUTO (2)
+
+#define PSB_CR_CORE_ID 0x0010
+#define _PSB_CC_ID_ID_SHIFT (16)
+#define _PSB_CC_ID_ID_MASK (0xFFFF << 16)
+#define _PSB_CC_ID_CONFIG_SHIFT (0)
+#define _PSB_CC_ID_CONFIG_MASK (0xFFFF << 0)
+
+#define PSB_CR_CORE_REVISION 0x0014
+#define _PSB_CC_REVISION_DESIGNER_SHIFT (24)
+#define _PSB_CC_REVISION_DESIGNER_MASK (0xFF << 24)
+#define _PSB_CC_REVISION_MAJOR_SHIFT (16)
+#define _PSB_CC_REVISION_MAJOR_MASK (0xFF << 16)
+#define _PSB_CC_REVISION_MINOR_SHIFT (8)
+#define _PSB_CC_REVISION_MINOR_MASK (0xFF << 8)
+#define _PSB_CC_REVISION_MAINTENANCE_SHIFT (0)
+#define _PSB_CC_REVISION_MAINTENANCE_MASK (0xFF << 0)
+
+#define PSB_CR_DESIGNER_REV_FIELD1 0x0018
+
+#define PSB_CR_SOFT_RESET 0x0080
+#define _PSB_CS_RESET_TSP_RESET (1 << 6)
+#define _PSB_CS_RESET_ISP_RESET (1 << 5)
+#define _PSB_CS_RESET_USE_RESET (1 << 4)
+#define _PSB_CS_RESET_TA_RESET (1 << 3)
+#define _PSB_CS_RESET_DPM_RESET (1 << 2)
+#define _PSB_CS_RESET_TWOD_RESET (1 << 1)
+#define _PSB_CS_RESET_BIF_RESET (1 << 0)
+
+#define PSB_CR_DESIGNER_REV_FIELD2 0x001C
+
+#define PSB_CR_EVENT_HOST_ENABLE2 0x0110
+
+#define PSB_CR_EVENT_STATUS2 0x0118
+
+#define PSB_CR_EVENT_HOST_CLEAR2 0x0114
+#define _PSB_CE2_BIF_REQUESTER_FAULT (1 << 4)
+
+#define PSB_CR_EVENT_STATUS 0x012C
+
+#define PSB_CR_EVENT_HOST_ENABLE 0x0130
+
+#define PSB_CR_EVENT_HOST_CLEAR 0x0134
+#define _PSB_CE_MASTER_INTERRUPT (1 << 31)
+#define _PSB_CE_TA_DPM_FAULT (1 << 28)
+#define _PSB_CE_TWOD_COMPLETE (1 << 27)
+#define _PSB_CE_DPM_OUT_OF_MEMORY_ZLS (1 << 25)
+#define _PSB_CE_DPM_TA_MEM_FREE (1 << 24)
+#define _PSB_CE_PIXELBE_END_RENDER (1 << 18)
+#define _PSB_CE_SW_EVENT (1 << 14)
+#define _PSB_CE_TA_FINISHED (1 << 13)
+#define _PSB_CE_TA_TERMINATE (1 << 12)
+#define _PSB_CE_DPM_REACHED_MEM_THRESH (1 << 3)
+#define _PSB_CE_DPM_OUT_OF_MEMORY_GBL (1 << 2)
+#define _PSB_CE_DPM_OUT_OF_MEMORY_MT (1 << 1)
+#define _PSB_CE_DPM_3D_MEM_FREE (1 << 0)
+
+
+#define PSB_USE_OFFSET_MASK 0x0007FFFF
+#define PSB_USE_OFFSET_SIZE (PSB_USE_OFFSET_MASK + 1)
+#define PSB_CR_USE_CODE_BASE0 0x0A0C
+#define PSB_CR_USE_CODE_BASE1 0x0A10
+#define PSB_CR_USE_CODE_BASE2 0x0A14
+#define PSB_CR_USE_CODE_BASE3 0x0A18
+#define PSB_CR_USE_CODE_BASE4 0x0A1C
+#define PSB_CR_USE_CODE_BASE5 0x0A20
+#define PSB_CR_USE_CODE_BASE6 0x0A24
+#define PSB_CR_USE_CODE_BASE7 0x0A28
+#define PSB_CR_USE_CODE_BASE8 0x0A2C
+#define PSB_CR_USE_CODE_BASE9 0x0A30
+#define PSB_CR_USE_CODE_BASE10 0x0A34
+#define PSB_CR_USE_CODE_BASE11 0x0A38
+#define PSB_CR_USE_CODE_BASE12 0x0A3C
+#define PSB_CR_USE_CODE_BASE13 0x0A40
+#define PSB_CR_USE_CODE_BASE14 0x0A44
+#define PSB_CR_USE_CODE_BASE15 0x0A48
+#define PSB_CR_USE_CODE_BASE(_i) (0x0A0C + ((_i) << 2))
+#define _PSB_CUC_BASE_DM_SHIFT (25)
+#define _PSB_CUC_BASE_DM_MASK (0x3 << 25)
+#define _PSB_CUC_BASE_ADDR_SHIFT (0) /* 1024-bit aligned address? */
+#define _PSB_CUC_BASE_ADDR_ALIGNSHIFT (7)
+#define _PSB_CUC_BASE_ADDR_MASK (0x1FFFFFF << 0)
+#define _PSB_CUC_DM_VERTEX (0)
+#define _PSB_CUC_DM_PIXEL (1)
+#define _PSB_CUC_DM_RESERVED (2)
+#define _PSB_CUC_DM_EDM (3)
+
+#define PSB_CR_PDS_EXEC_BASE 0x0AB8
+#define _PSB_CR_PDS_EXEC_BASE_ADDR_SHIFT (20) /* 1MB aligned address */
+#define _PSB_CR_PDS_EXEC_BASE_ADDR_ALIGNSHIFT (20)
+
+#define PSB_CR_EVENT_KICKER 0x0AC4
+#define _PSB_CE_KICKER_ADDRESS_SHIFT (4) /* 128-bit aligned address */
+
+#define PSB_CR_EVENT_KICK 0x0AC8
+#define _PSB_CE_KICK_NOW (1 << 0)
+
+#define PSB_CR_BIF_DIR_LIST_BASE1 0x0C38
+
+#define PSB_CR_BIF_CTRL 0x0C00
+#define _PSB_CB_CTRL_CLEAR_FAULT (1 << 4)
+#define _PSB_CB_CTRL_INVALDC (1 << 3)
+#define _PSB_CB_CTRL_FLUSH (1 << 2)
+
+#define PSB_CR_BIF_INT_STAT 0x0C04
+
+#define PSB_CR_BIF_FAULT 0x0C08
+#define _PSB_CBI_STAT_PF_N_RW (1 << 14)
+#define _PSB_CBI_STAT_FAULT_SHIFT (0)
+#define _PSB_CBI_STAT_FAULT_MASK (0x3FFF << 0)
+#define _PSB_CBI_STAT_FAULT_CACHE (1 << 1)
+#define _PSB_CBI_STAT_FAULT_TA (1 << 2)
+#define _PSB_CBI_STAT_FAULT_VDM (1 << 3)
+#define _PSB_CBI_STAT_FAULT_2D (1 << 4)
+#define _PSB_CBI_STAT_FAULT_PBE (1 << 5)
+#define _PSB_CBI_STAT_FAULT_TSP (1 << 6)
+#define _PSB_CBI_STAT_FAULT_ISP (1 << 7)
+#define _PSB_CBI_STAT_FAULT_USSEPDS (1 << 8)
+#define _PSB_CBI_STAT_FAULT_HOST (1 << 9)
+
+#define PSB_CR_BIF_BANK0 0x0C78
+#define PSB_CR_BIF_BANK1 0x0C7C
+#define PSB_CR_BIF_DIR_LIST_BASE0 0x0C84
+#define PSB_CR_BIF_TWOD_REQ_BASE 0x0C88
+#define PSB_CR_BIF_3D_REQ_BASE 0x0CAC
+
+#define PSB_CR_2D_SOCIF 0x0E18
+#define _PSB_C2_SOCIF_FREESPACE_SHIFT (0)
+#define _PSB_C2_SOCIF_FREESPACE_MASK (0xFF << 0)
+#define _PSB_C2_SOCIF_EMPTY (0x80 << 0)
+
+#define PSB_CR_2D_BLIT_STATUS 0x0E04
+#define _PSB_C2B_STATUS_BUSY (1 << 24)
+#define _PSB_C2B_STATUS_COMPLETE_SHIFT (0)
+#define _PSB_C2B_STATUS_COMPLETE_MASK (0xFFFFFF << 0)
/*
* 2D defs.
* 2D Slave Port Data : Block Header's Object Type
*/
-#define PSB_2D_CLIP_BH (0x00000000)
-#define PSB_2D_PAT_BH (0x10000000)
-#define PSB_2D_CTRL_BH (0x20000000)
-#define PSB_2D_SRC_OFF_BH (0x30000000)
-#define PSB_2D_MASK_OFF_BH (0x40000000)
-#define PSB_2D_RESERVED1_BH (0x50000000)
-#define PSB_2D_RESERVED2_BH (0x60000000)
-#define PSB_2D_FENCE_BH (0x70000000)
-#define PSB_2D_BLIT_BH (0x80000000)
-#define PSB_2D_SRC_SURF_BH (0x90000000)
-#define PSB_2D_DST_SURF_BH (0xA0000000)
-#define PSB_2D_PAT_SURF_BH (0xB0000000)
-#define PSB_2D_SRC_PAL_BH (0xC0000000)
-#define PSB_2D_PAT_PAL_BH (0xD0000000)
-#define PSB_2D_MASK_SURF_BH (0xE0000000)
-#define PSB_2D_FLUSH_BH (0xF0000000)
+#define PSB_2D_CLIP_BH (0x00000000)
+#define PSB_2D_PAT_BH (0x10000000)
+#define PSB_2D_CTRL_BH (0x20000000)
+#define PSB_2D_SRC_OFF_BH (0x30000000)
+#define PSB_2D_MASK_OFF_BH (0x40000000)
+#define PSB_2D_RESERVED1_BH (0x50000000)
+#define PSB_2D_RESERVED2_BH (0x60000000)
+#define PSB_2D_FENCE_BH (0x70000000)
+#define PSB_2D_BLIT_BH (0x80000000)
+#define PSB_2D_SRC_SURF_BH (0x90000000)
+#define PSB_2D_DST_SURF_BH (0xA0000000)
+#define PSB_2D_PAT_SURF_BH (0xB0000000)
+#define PSB_2D_SRC_PAL_BH (0xC0000000)
+#define PSB_2D_PAT_PAL_BH (0xD0000000)
+#define PSB_2D_MASK_SURF_BH (0xE0000000)
+#define PSB_2D_FLUSH_BH (0xF0000000)
/*
* Clip Definition block (PSB_2D_CLIP_BH)
*/
-#define PSB_2D_CLIPCOUNT_MAX (1)
-#define PSB_2D_CLIPCOUNT_MASK (0x00000000)
-#define PSB_2D_CLIPCOUNT_CLRMASK (0xFFFFFFFF)
-#define PSB_2D_CLIPCOUNT_SHIFT (0)
+#define PSB_2D_CLIPCOUNT_MAX (1)
+#define PSB_2D_CLIPCOUNT_MASK (0x00000000)
+#define PSB_2D_CLIPCOUNT_CLRMASK (0xFFFFFFFF)
+#define PSB_2D_CLIPCOUNT_SHIFT (0)
/* clip rectangle min & max */
-#define PSB_2D_CLIP_XMAX_MASK (0x00FFF000)
-#define PSB_2D_CLIP_XMAX_CLRMASK (0xFF000FFF)
-#define PSB_2D_CLIP_XMAX_SHIFT (12)
-#define PSB_2D_CLIP_XMIN_MASK (0x00000FFF)
-#define PSB_2D_CLIP_XMIN_CLRMASK (0x00FFF000)
-#define PSB_2D_CLIP_XMIN_SHIFT (0)
+#define PSB_2D_CLIP_XMAX_MASK (0x00FFF000)
+#define PSB_2D_CLIP_XMAX_CLRMASK (0xFF000FFF)
+#define PSB_2D_CLIP_XMAX_SHIFT (12)
+#define PSB_2D_CLIP_XMIN_MASK (0x00000FFF)
+#define PSB_2D_CLIP_XMIN_CLRMASK (0x00FFF000)
+#define PSB_2D_CLIP_XMIN_SHIFT (0)
/* clip rectangle offset */
-#define PSB_2D_CLIP_YMAX_MASK (0x00FFF000)
-#define PSB_2D_CLIP_YMAX_CLRMASK (0xFF000FFF)
-#define PSB_2D_CLIP_YMAX_SHIFT (12)
-#define PSB_2D_CLIP_YMIN_MASK (0x00000FFF)
-#define PSB_2D_CLIP_YMIN_CLRMASK (0x00FFF000)
-#define PSB_2D_CLIP_YMIN_SHIFT (0)
+#define PSB_2D_CLIP_YMAX_MASK (0x00FFF000)
+#define PSB_2D_CLIP_YMAX_CLRMASK (0xFF000FFF)
+#define PSB_2D_CLIP_YMAX_SHIFT (12)
+#define PSB_2D_CLIP_YMIN_MASK (0x00000FFF)
+#define PSB_2D_CLIP_YMIN_CLRMASK (0x00FFF000)
+#define PSB_2D_CLIP_YMIN_SHIFT (0)
/*
* Pattern Control (PSB_2D_PAT_BH)
*/
-#define PSB_2D_PAT_HEIGHT_MASK (0x0000001F)
-#define PSB_2D_PAT_HEIGHT_SHIFT (0)
-#define PSB_2D_PAT_WIDTH_MASK (0x000003E0)
-#define PSB_2D_PAT_WIDTH_SHIFT (5)
-#define PSB_2D_PAT_YSTART_MASK (0x00007C00)
-#define PSB_2D_PAT_YSTART_SHIFT (10)
-#define PSB_2D_PAT_XSTART_MASK (0x000F8000)
-#define PSB_2D_PAT_XSTART_SHIFT (15)
+#define PSB_2D_PAT_HEIGHT_MASK (0x0000001F)
+#define PSB_2D_PAT_HEIGHT_SHIFT (0)
+#define PSB_2D_PAT_WIDTH_MASK (0x000003E0)
+#define PSB_2D_PAT_WIDTH_SHIFT (5)
+#define PSB_2D_PAT_YSTART_MASK (0x00007C00)
+#define PSB_2D_PAT_YSTART_SHIFT (10)
+#define PSB_2D_PAT_XSTART_MASK (0x000F8000)
+#define PSB_2D_PAT_XSTART_SHIFT (15)
/*
* 2D Control block (PSB_2D_CTRL_BH)
*/
/* Present Flags */
-#define PSB_2D_SRCCK_CTRL (0x00000001)
-#define PSB_2D_DSTCK_CTRL (0x00000002)
-#define PSB_2D_ALPHA_CTRL (0x00000004)
+#define PSB_2D_SRCCK_CTRL (0x00000001)
+#define PSB_2D_DSTCK_CTRL (0x00000002)
+#define PSB_2D_ALPHA_CTRL (0x00000004)
/* Colour Key Colour (SRC/DST)*/
-#define PSB_2D_CK_COL_MASK (0xFFFFFFFF)
-#define PSB_2D_CK_COL_CLRMASK (0x00000000)
-#define PSB_2D_CK_COL_SHIFT (0)
+#define PSB_2D_CK_COL_MASK (0xFFFFFFFF)
+#define PSB_2D_CK_COL_CLRMASK (0x00000000)
+#define PSB_2D_CK_COL_SHIFT (0)
/* Colour Key Mask (SRC/DST)*/
-#define PSB_2D_CK_MASK_MASK (0xFFFFFFFF)
-#define PSB_2D_CK_MASK_CLRMASK (0x00000000)
-#define PSB_2D_CK_MASK_SHIFT (0)
+#define PSB_2D_CK_MASK_MASK (0xFFFFFFFF)
+#define PSB_2D_CK_MASK_CLRMASK (0x00000000)
+#define PSB_2D_CK_MASK_SHIFT (0)
/* Alpha Control (Alpha/RGB)*/
-#define PSB_2D_GBLALPHA_MASK (0x000FF000)
-#define PSB_2D_GBLALPHA_CLRMASK (0xFFF00FFF)
-#define PSB_2D_GBLALPHA_SHIFT (12)
-#define PSB_2D_SRCALPHA_OP_MASK (0x00700000)
-#define PSB_2D_SRCALPHA_OP_CLRMASK (0xFF8FFFFF)
-#define PSB_2D_SRCALPHA_OP_SHIFT (20)
-#define PSB_2D_SRCALPHA_OP_ONE (0x00000000)
-#define PSB_2D_SRCALPHA_OP_SRC (0x00100000)
-#define PSB_2D_SRCALPHA_OP_DST (0x00200000)
-#define PSB_2D_SRCALPHA_OP_SG (0x00300000)
-#define PSB_2D_SRCALPHA_OP_DG (0x00400000)
-#define PSB_2D_SRCALPHA_OP_GBL (0x00500000)
-#define PSB_2D_SRCALPHA_OP_ZERO (0x00600000)
-#define PSB_2D_SRCALPHA_INVERT (0x00800000)
-#define PSB_2D_SRCALPHA_INVERT_CLR (0xFF7FFFFF)
-#define PSB_2D_DSTALPHA_OP_MASK (0x07000000)
-#define PSB_2D_DSTALPHA_OP_CLRMASK (0xF8FFFFFF)
-#define PSB_2D_DSTALPHA_OP_SHIFT (24)
-#define PSB_2D_DSTALPHA_OP_ONE (0x00000000)
-#define PSB_2D_DSTALPHA_OP_SRC (0x01000000)
-#define PSB_2D_DSTALPHA_OP_DST (0x02000000)
-#define PSB_2D_DSTALPHA_OP_SG (0x03000000)
-#define PSB_2D_DSTALPHA_OP_DG (0x04000000)
-#define PSB_2D_DSTALPHA_OP_GBL (0x05000000)
-#define PSB_2D_DSTALPHA_OP_ZERO (0x06000000)
-#define PSB_2D_DSTALPHA_INVERT (0x08000000)
-#define PSB_2D_DSTALPHA_INVERT_CLR (0xF7FFFFFF)
-
-#define PSB_2D_PRE_MULTIPLICATION_ENABLE (0x10000000)
-#define PSB_2D_PRE_MULTIPLICATION_CLRMASK (0xEFFFFFFF)
-#define PSB_2D_ZERO_SOURCE_ALPHA_ENABLE (0x20000000)
-#define PSB_2D_ZERO_SOURCE_ALPHA_CLRMASK (0xDFFFFFFF)
+#define PSB_2D_GBLALPHA_MASK (0x000FF000)
+#define PSB_2D_GBLALPHA_CLRMASK (0xFFF00FFF)
+#define PSB_2D_GBLALPHA_SHIFT (12)
+#define PSB_2D_SRCALPHA_OP_MASK (0x00700000)
+#define PSB_2D_SRCALPHA_OP_CLRMASK (0xFF8FFFFF)
+#define PSB_2D_SRCALPHA_OP_SHIFT (20)
+#define PSB_2D_SRCALPHA_OP_ONE (0x00000000)
+#define PSB_2D_SRCALPHA_OP_SRC (0x00100000)
+#define PSB_2D_SRCALPHA_OP_DST (0x00200000)
+#define PSB_2D_SRCALPHA_OP_SG (0x00300000)
+#define PSB_2D_SRCALPHA_OP_DG (0x00400000)
+#define PSB_2D_SRCALPHA_OP_GBL (0x00500000)
+#define PSB_2D_SRCALPHA_OP_ZERO (0x00600000)
+#define PSB_2D_SRCALPHA_INVERT (0x00800000)
+#define PSB_2D_SRCALPHA_INVERT_CLR (0xFF7FFFFF)
+#define PSB_2D_DSTALPHA_OP_MASK (0x07000000)
+#define PSB_2D_DSTALPHA_OP_CLRMASK (0xF8FFFFFF)
+#define PSB_2D_DSTALPHA_OP_SHIFT (24)
+#define PSB_2D_DSTALPHA_OP_ONE (0x00000000)
+#define PSB_2D_DSTALPHA_OP_SRC (0x01000000)
+#define PSB_2D_DSTALPHA_OP_DST (0x02000000)
+#define PSB_2D_DSTALPHA_OP_SG (0x03000000)
+#define PSB_2D_DSTALPHA_OP_DG (0x04000000)
+#define PSB_2D_DSTALPHA_OP_GBL (0x05000000)
+#define PSB_2D_DSTALPHA_OP_ZERO (0x06000000)
+#define PSB_2D_DSTALPHA_INVERT (0x08000000)
+#define PSB_2D_DSTALPHA_INVERT_CLR (0xF7FFFFFF)
+
+#define PSB_2D_PRE_MULTIPLICATION_ENABLE (0x10000000)
+#define PSB_2D_PRE_MULTIPLICATION_CLRMASK (0xEFFFFFFF)
+#define PSB_2D_ZERO_SOURCE_ALPHA_ENABLE (0x20000000)
+#define PSB_2D_ZERO_SOURCE_ALPHA_CLRMASK (0xDFFFFFFF)
/*
*Source Offset (PSB_2D_SRC_OFF_BH)
*/
-#define PSB_2D_SRCOFF_XSTART_MASK ((0x00000FFF) << 12)
-#define PSB_2D_SRCOFF_XSTART_SHIFT (12)
-#define PSB_2D_SRCOFF_YSTART_MASK (0x00000FFF)
-#define PSB_2D_SRCOFF_YSTART_SHIFT (0)
+#define PSB_2D_SRCOFF_XSTART_MASK ((0x00000FFF) << 12)
+#define PSB_2D_SRCOFF_XSTART_SHIFT (12)
+#define PSB_2D_SRCOFF_YSTART_MASK (0x00000FFF)
+#define PSB_2D_SRCOFF_YSTART_SHIFT (0)
/*
* Mask Offset (PSB_2D_MASK_OFF_BH)
*/
-#define PSB_2D_MASKOFF_XSTART_MASK ((0x00000FFF) << 12)
-#define PSB_2D_MASKOFF_XSTART_SHIFT (12)
-#define PSB_2D_MASKOFF_YSTART_MASK (0x00000FFF)
-#define PSB_2D_MASKOFF_YSTART_SHIFT (0)
+#define PSB_2D_MASKOFF_XSTART_MASK ((0x00000FFF) << 12)
+#define PSB_2D_MASKOFF_XSTART_SHIFT (12)
+#define PSB_2D_MASKOFF_YSTART_MASK (0x00000FFF)
+#define PSB_2D_MASKOFF_YSTART_SHIFT (0)
/*
* 2D Fence (see PSB_2D_FENCE_BH): bits 0:27 are ignored
*Blit Rectangle (PSB_2D_BLIT_BH)
*/
-#define PSB_2D_ROT_MASK (3<<25)
-#define PSB_2D_ROT_CLRMASK (~PSB_2D_ROT_MASK)
-#define PSB_2D_ROT_NONE (0<<25)
-#define PSB_2D_ROT_90DEGS (1<<25)
-#define PSB_2D_ROT_180DEGS (2<<25)
-#define PSB_2D_ROT_270DEGS (3<<25)
-
-#define PSB_2D_COPYORDER_MASK (3<<23)
-#define PSB_2D_COPYORDER_CLRMASK (~PSB_2D_COPYORDER_MASK)
-#define PSB_2D_COPYORDER_TL2BR (0<<23)
-#define PSB_2D_COPYORDER_BR2TL (1<<23)
-#define PSB_2D_COPYORDER_TR2BL (2<<23)
-#define PSB_2D_COPYORDER_BL2TR (3<<23)
-
-#define PSB_2D_DSTCK_CLRMASK (0xFF9FFFFF)
-#define PSB_2D_DSTCK_DISABLE (0x00000000)
-#define PSB_2D_DSTCK_PASS (0x00200000)
-#define PSB_2D_DSTCK_REJECT (0x00400000)
-
-#define PSB_2D_SRCCK_CLRMASK (0xFFE7FFFF)
-#define PSB_2D_SRCCK_DISABLE (0x00000000)
-#define PSB_2D_SRCCK_PASS (0x00080000)
-#define PSB_2D_SRCCK_REJECT (0x00100000)
-
-#define PSB_2D_CLIP_ENABLE (0x00040000)
-
-#define PSB_2D_ALPHA_ENABLE (0x00020000)
-
-#define PSB_2D_PAT_CLRMASK (0xFFFEFFFF)
-#define PSB_2D_PAT_MASK (0x00010000)
-#define PSB_2D_USE_PAT (0x00010000)
-#define PSB_2D_USE_FILL (0x00000000)
+#define PSB_2D_ROT_MASK (3 << 25)
+#define PSB_2D_ROT_CLRMASK (~PSB_2D_ROT_MASK)
+#define PSB_2D_ROT_NONE (0 << 25)
+#define PSB_2D_ROT_90DEGS (1 << 25)
+#define PSB_2D_ROT_180DEGS (2 << 25)
+#define PSB_2D_ROT_270DEGS (3 << 25)
+
+#define PSB_2D_COPYORDER_MASK (3 << 23)
+#define PSB_2D_COPYORDER_CLRMASK (~PSB_2D_COPYORDER_MASK)
+#define PSB_2D_COPYORDER_TL2BR (0 << 23)
+#define PSB_2D_COPYORDER_BR2TL (1 << 23)
+#define PSB_2D_COPYORDER_TR2BL (2 << 23)
+#define PSB_2D_COPYORDER_BL2TR (3 << 23)
+
+#define PSB_2D_DSTCK_CLRMASK (0xFF9FFFFF)
+#define PSB_2D_DSTCK_DISABLE (0x00000000)
+#define PSB_2D_DSTCK_PASS (0x00200000)
+#define PSB_2D_DSTCK_REJECT (0x00400000)
+
+#define PSB_2D_SRCCK_CLRMASK (0xFFE7FFFF)
+#define PSB_2D_SRCCK_DISABLE (0x00000000)
+#define PSB_2D_SRCCK_PASS (0x00080000)
+#define PSB_2D_SRCCK_REJECT (0x00100000)
+
+#define PSB_2D_CLIP_ENABLE (0x00040000)
+
+#define PSB_2D_ALPHA_ENABLE (0x00020000)
+
+#define PSB_2D_PAT_CLRMASK (0xFFFEFFFF)
+#define PSB_2D_PAT_MASK (0x00010000)
+#define PSB_2D_USE_PAT (0x00010000)
+#define PSB_2D_USE_FILL (0x00000000)
/*
* Tungsten Graphics note on rop codes: If rop A and rop B are
* identical, the mask surface will not be read and need not be
* set up.
*/
-#define PSB_2D_ROP3B_MASK (0x0000FF00)
-#define PSB_2D_ROP3B_CLRMASK (0xFFFF00FF)
-#define PSB_2D_ROP3B_SHIFT (8)
+#define PSB_2D_ROP3B_MASK (0x0000FF00)
+#define PSB_2D_ROP3B_CLRMASK (0xFFFF00FF)
+#define PSB_2D_ROP3B_SHIFT (8)
/* rop code A */
-#define PSB_2D_ROP3A_MASK (0x000000FF)
-#define PSB_2D_ROP3A_CLRMASK (0xFFFFFF00)
-#define PSB_2D_ROP3A_SHIFT (0)
+#define PSB_2D_ROP3A_MASK (0x000000FF)
+#define PSB_2D_ROP3A_CLRMASK (0xFFFFFF00)
+#define PSB_2D_ROP3A_SHIFT (0)
-#define PSB_2D_ROP4_MASK (0x0000FFFF)
+#define PSB_2D_ROP4_MASK (0x0000FFFF)
/*
* DWORD0: (Only pass if Pattern control == Use Fill Colour)
* Fill Colour RGBA8888
*/
-#define PSB_2D_FILLCOLOUR_MASK (0xFFFFFFFF)
-#define PSB_2D_FILLCOLOUR_SHIFT (0)
+#define PSB_2D_FILLCOLOUR_MASK (0xFFFFFFFF)
+#define PSB_2D_FILLCOLOUR_SHIFT (0)
/*
* DWORD1: (Always Present)
* X Start (Dest)
* Y Start (Dest)
*/
-#define PSB_2D_DST_XSTART_MASK (0x00FFF000)
-#define PSB_2D_DST_XSTART_CLRMASK (0xFF000FFF)
-#define PSB_2D_DST_XSTART_SHIFT (12)
-#define PSB_2D_DST_YSTART_MASK (0x00000FFF)
-#define PSB_2D_DST_YSTART_CLRMASK (0xFFFFF000)
-#define PSB_2D_DST_YSTART_SHIFT (0)
+#define PSB_2D_DST_XSTART_MASK (0x00FFF000)
+#define PSB_2D_DST_XSTART_CLRMASK (0xFF000FFF)
+#define PSB_2D_DST_XSTART_SHIFT (12)
+#define PSB_2D_DST_YSTART_MASK (0x00000FFF)
+#define PSB_2D_DST_YSTART_CLRMASK (0xFFFFF000)
+#define PSB_2D_DST_YSTART_SHIFT (0)
/*
* DWORD2: (Always Present)
* X Size (Dest)
* Y Size (Dest)
*/
-#define PSB_2D_DST_XSIZE_MASK (0x00FFF000)
-#define PSB_2D_DST_XSIZE_CLRMASK (0xFF000FFF)
-#define PSB_2D_DST_XSIZE_SHIFT (12)
-#define PSB_2D_DST_YSIZE_MASK (0x00000FFF)
-#define PSB_2D_DST_YSIZE_CLRMASK (0xFFFFF000)
-#define PSB_2D_DST_YSIZE_SHIFT (0)
+#define PSB_2D_DST_XSIZE_MASK (0x00FFF000)
+#define PSB_2D_DST_XSIZE_CLRMASK (0xFF000FFF)
+#define PSB_2D_DST_XSIZE_SHIFT (12)
+#define PSB_2D_DST_YSIZE_MASK (0x00000FFF)
+#define PSB_2D_DST_YSIZE_CLRMASK (0xFFFFF000)
+#define PSB_2D_DST_YSIZE_SHIFT (0)
/*
* Source Surface (PSB_2D_SRC_SURF_BH)
*/
/*
- * WORD 0
+ * WORD 0
*/
-#define PSB_2D_SRC_FORMAT_MASK (0x00078000)
-#define PSB_2D_SRC_1_PAL (0x00000000)
-#define PSB_2D_SRC_2_PAL (0x00008000)
-#define PSB_2D_SRC_4_PAL (0x00010000)
-#define PSB_2D_SRC_8_PAL (0x00018000)
-#define PSB_2D_SRC_8_ALPHA (0x00020000)
-#define PSB_2D_SRC_4_ALPHA (0x00028000)
-#define PSB_2D_SRC_332RGB (0x00030000)
-#define PSB_2D_SRC_4444ARGB (0x00038000)
-#define PSB_2D_SRC_555RGB (0x00040000)
-#define PSB_2D_SRC_1555ARGB (0x00048000)
-#define PSB_2D_SRC_565RGB (0x00050000)
-#define PSB_2D_SRC_0888ARGB (0x00058000)
-#define PSB_2D_SRC_8888ARGB (0x00060000)
-#define PSB_2D_SRC_8888UYVY (0x00068000)
-#define PSB_2D_SRC_RESERVED (0x00070000)
-#define PSB_2D_SRC_1555ARGB_LOOKUP (0x00078000)
-
-
-#define PSB_2D_SRC_STRIDE_MASK (0x00007FFF)
-#define PSB_2D_SRC_STRIDE_CLRMASK (0xFFFF8000)
-#define PSB_2D_SRC_STRIDE_SHIFT (0)
+#define PSB_2D_SRC_FORMAT_MASK (0x00078000)
+#define PSB_2D_SRC_1_PAL (0x00000000)
+#define PSB_2D_SRC_2_PAL (0x00008000)
+#define PSB_2D_SRC_4_PAL (0x00010000)
+#define PSB_2D_SRC_8_PAL (0x00018000)
+#define PSB_2D_SRC_8_ALPHA (0x00020000)
+#define PSB_2D_SRC_4_ALPHA (0x00028000)
+#define PSB_2D_SRC_332RGB (0x00030000)
+#define PSB_2D_SRC_4444ARGB (0x00038000)
+#define PSB_2D_SRC_555RGB (0x00040000)
+#define PSB_2D_SRC_1555ARGB (0x00048000)
+#define PSB_2D_SRC_565RGB (0x00050000)
+#define PSB_2D_SRC_0888ARGB (0x00058000)
+#define PSB_2D_SRC_8888ARGB (0x00060000)
+#define PSB_2D_SRC_8888UYVY (0x00068000)
+#define PSB_2D_SRC_RESERVED (0x00070000)
+#define PSB_2D_SRC_1555ARGB_LOOKUP (0x00078000)
+
+
+#define PSB_2D_SRC_STRIDE_MASK (0x00007FFF)
+#define PSB_2D_SRC_STRIDE_CLRMASK (0xFFFF8000)
+#define PSB_2D_SRC_STRIDE_SHIFT (0)
/*
* WORD 1 - Base Address
*/
-#define PSB_2D_SRC_ADDR_MASK (0x0FFFFFFC)
-#define PSB_2D_SRC_ADDR_CLRMASK (0x00000003)
-#define PSB_2D_SRC_ADDR_SHIFT (2)
-#define PSB_2D_SRC_ADDR_ALIGNSHIFT (2)
+#define PSB_2D_SRC_ADDR_MASK (0x0FFFFFFC)
+#define PSB_2D_SRC_ADDR_CLRMASK (0x00000003)
+#define PSB_2D_SRC_ADDR_SHIFT (2)
+#define PSB_2D_SRC_ADDR_ALIGNSHIFT (2)
/*
* Pattern Surface (PSB_2D_PAT_SURF_BH)
* WORD 0
*/
-#define PSB_2D_PAT_FORMAT_MASK (0x00078000)
-#define PSB_2D_PAT_1_PAL (0x00000000)
-#define PSB_2D_PAT_2_PAL (0x00008000)
-#define PSB_2D_PAT_4_PAL (0x00010000)
-#define PSB_2D_PAT_8_PAL (0x00018000)
-#define PSB_2D_PAT_8_ALPHA (0x00020000)
-#define PSB_2D_PAT_4_ALPHA (0x00028000)
-#define PSB_2D_PAT_332RGB (0x00030000)
-#define PSB_2D_PAT_4444ARGB (0x00038000)
-#define PSB_2D_PAT_555RGB (0x00040000)
-#define PSB_2D_PAT_1555ARGB (0x00048000)
-#define PSB_2D_PAT_565RGB (0x00050000)
-#define PSB_2D_PAT_0888ARGB (0x00058000)
-#define PSB_2D_PAT_8888ARGB (0x00060000)
-
-#define PSB_2D_PAT_STRIDE_MASK (0x00007FFF)
-#define PSB_2D_PAT_STRIDE_CLRMASK (0xFFFF8000)
-#define PSB_2D_PAT_STRIDE_SHIFT (0)
+#define PSB_2D_PAT_FORMAT_MASK (0x00078000)
+#define PSB_2D_PAT_1_PAL (0x00000000)
+#define PSB_2D_PAT_2_PAL (0x00008000)
+#define PSB_2D_PAT_4_PAL (0x00010000)
+#define PSB_2D_PAT_8_PAL (0x00018000)
+#define PSB_2D_PAT_8_ALPHA (0x00020000)
+#define PSB_2D_PAT_4_ALPHA (0x00028000)
+#define PSB_2D_PAT_332RGB (0x00030000)
+#define PSB_2D_PAT_4444ARGB (0x00038000)
+#define PSB_2D_PAT_555RGB (0x00040000)
+#define PSB_2D_PAT_1555ARGB (0x00048000)
+#define PSB_2D_PAT_565RGB (0x00050000)
+#define PSB_2D_PAT_0888ARGB (0x00058000)
+#define PSB_2D_PAT_8888ARGB (0x00060000)
+
+#define PSB_2D_PAT_STRIDE_MASK (0x00007FFF)
+#define PSB_2D_PAT_STRIDE_CLRMASK (0xFFFF8000)
+#define PSB_2D_PAT_STRIDE_SHIFT (0)
/*
* WORD 1 - Base Address
*/
-#define PSB_2D_PAT_ADDR_MASK (0x0FFFFFFC)
-#define PSB_2D_PAT_ADDR_CLRMASK (0x00000003)
-#define PSB_2D_PAT_ADDR_SHIFT (2)
-#define PSB_2D_PAT_ADDR_ALIGNSHIFT (2)
+#define PSB_2D_PAT_ADDR_MASK (0x0FFFFFFC)
+#define PSB_2D_PAT_ADDR_CLRMASK (0x00000003)
+#define PSB_2D_PAT_ADDR_SHIFT (2)
+#define PSB_2D_PAT_ADDR_ALIGNSHIFT (2)
/*
* Destination Surface (PSB_2D_DST_SURF_BH)
* WORD 0
*/
-#define PSB_2D_DST_FORMAT_MASK (0x00078000)
-#define PSB_2D_DST_332RGB (0x00030000)
-#define PSB_2D_DST_4444ARGB (0x00038000)
-#define PSB_2D_DST_555RGB (0x00040000)
-#define PSB_2D_DST_1555ARGB (0x00048000)
-#define PSB_2D_DST_565RGB (0x00050000)
-#define PSB_2D_DST_0888ARGB (0x00058000)
-#define PSB_2D_DST_8888ARGB (0x00060000)
-#define PSB_2D_DST_8888AYUV (0x00070000)
-
-#define PSB_2D_DST_STRIDE_MASK (0x00007FFF)
-#define PSB_2D_DST_STRIDE_CLRMASK (0xFFFF8000)
-#define PSB_2D_DST_STRIDE_SHIFT (0)
+#define PSB_2D_DST_FORMAT_MASK (0x00078000)
+#define PSB_2D_DST_332RGB (0x00030000)
+#define PSB_2D_DST_4444ARGB (0x00038000)
+#define PSB_2D_DST_555RGB (0x00040000)
+#define PSB_2D_DST_1555ARGB (0x00048000)
+#define PSB_2D_DST_565RGB (0x00050000)
+#define PSB_2D_DST_0888ARGB (0x00058000)
+#define PSB_2D_DST_8888ARGB (0x00060000)
+#define PSB_2D_DST_8888AYUV (0x00070000)
+
+#define PSB_2D_DST_STRIDE_MASK (0x00007FFF)
+#define PSB_2D_DST_STRIDE_CLRMASK (0xFFFF8000)
+#define PSB_2D_DST_STRIDE_SHIFT (0)
/*
* WORD 1 - Base Address
*/
-#define PSB_2D_DST_ADDR_MASK (0x0FFFFFFC)
-#define PSB_2D_DST_ADDR_CLRMASK (0x00000003)
-#define PSB_2D_DST_ADDR_SHIFT (2)
-#define PSB_2D_DST_ADDR_ALIGNSHIFT (2)
+#define PSB_2D_DST_ADDR_MASK (0x0FFFFFFC)
+#define PSB_2D_DST_ADDR_CLRMASK (0x00000003)
+#define PSB_2D_DST_ADDR_SHIFT (2)
+#define PSB_2D_DST_ADDR_ALIGNSHIFT (2)
/*
* Mask Surface (PSB_2D_MASK_SURF_BH)
/*
* WORD 0
*/
-#define PSB_2D_MASK_STRIDE_MASK (0x00007FFF)
-#define PSB_2D_MASK_STRIDE_CLRMASK (0xFFFF8000)
-#define PSB_2D_MASK_STRIDE_SHIFT (0)
+#define PSB_2D_MASK_STRIDE_MASK (0x00007FFF)
+#define PSB_2D_MASK_STRIDE_CLRMASK (0xFFFF8000)
+#define PSB_2D_MASK_STRIDE_SHIFT (0)
/*
* WORD 1 - Base Address
*/
-#define PSB_2D_MASK_ADDR_MASK (0x0FFFFFFC)
-#define PSB_2D_MASK_ADDR_CLRMASK (0x00000003)
-#define PSB_2D_MASK_ADDR_SHIFT (2)
-#define PSB_2D_MASK_ADDR_ALIGNSHIFT (2)
+#define PSB_2D_MASK_ADDR_MASK (0x0FFFFFFC)
+#define PSB_2D_MASK_ADDR_CLRMASK (0x00000003)
+#define PSB_2D_MASK_ADDR_SHIFT (2)
+#define PSB_2D_MASK_ADDR_ALIGNSHIFT (2)
/*
* Source Palette (PSB_2D_SRC_PAL_BH)
*/
-#define PSB_2D_SRCPAL_ADDR_SHIFT (0)
-#define PSB_2D_SRCPAL_ADDR_CLRMASK (0xF0000007)
-#define PSB_2D_SRCPAL_ADDR_MASK (0x0FFFFFF8)
-#define PSB_2D_SRCPAL_BYTEALIGN (1024)
+#define PSB_2D_SRCPAL_ADDR_SHIFT (0)
+#define PSB_2D_SRCPAL_ADDR_CLRMASK (0xF0000007)
+#define PSB_2D_SRCPAL_ADDR_MASK (0x0FFFFFF8)
+#define PSB_2D_SRCPAL_BYTEALIGN (1024)
/*
* Pattern Palette (PSB_2D_PAT_PAL_BH)
*/
-#define PSB_2D_PATPAL_ADDR_SHIFT (0)
-#define PSB_2D_PATPAL_ADDR_CLRMASK (0xF0000007)
-#define PSB_2D_PATPAL_ADDR_MASK (0x0FFFFFF8)
-#define PSB_2D_PATPAL_BYTEALIGN (1024)
+#define PSB_2D_PATPAL_ADDR_SHIFT (0)
+#define PSB_2D_PATPAL_ADDR_CLRMASK (0xF0000007)
+#define PSB_2D_PATPAL_ADDR_MASK (0x0FFFFFF8)
+#define PSB_2D_PATPAL_BYTEALIGN (1024)
/*
* Rop3 Codes (2 LS bytes)
*/
-#define PSB_2D_ROP3_SRCCOPY (0xCCCC)
-#define PSB_2D_ROP3_PATCOPY (0xF0F0)
-#define PSB_2D_ROP3_WHITENESS (0xFFFF)
-#define PSB_2D_ROP3_BLACKNESS (0x0000)
-#define PSB_2D_ROP3_SRC (0xCC)
-#define PSB_2D_ROP3_PAT (0xF0)
-#define PSB_2D_ROP3_DST (0xAA)
-
+#define PSB_2D_ROP3_SRCCOPY (0xCCCC)
+#define PSB_2D_ROP3_PATCOPY (0xF0F0)
+#define PSB_2D_ROP3_WHITENESS (0xFFFF)
+#define PSB_2D_ROP3_BLACKNESS (0x0000)
+#define PSB_2D_ROP3_SRC (0xCC)
+#define PSB_2D_ROP3_PAT (0xF0)
+#define PSB_2D_ROP3_DST (0xAA)
/*
* Sizes.
*/
-#define PSB_SCENE_HW_COOKIE_SIZE 16
-#define PSB_TA_MEM_HW_COOKIE_SIZE 16
+#define PSB_SCENE_HW_COOKIE_SIZE 16
+#define PSB_TA_MEM_HW_COOKIE_SIZE 16
/*
* Scene stuff.
*/
-#define PSB_NUM_HW_SCENES 2
+#define PSB_NUM_HW_SCENES 2
/*
* Scheduler completion actions.
*/
-#define PSB_RASTER_BLOCK 0
-#define PSB_RASTER 1
-#define PSB_RETURN 2
-#define PSB_TA 3
-
-
-/*Power management*/
-#define PSB_PUNIT_PORT 0x04
-#define PSB_OSPMBA 0x78
-#define PSB_APMBA 0x7a
-#define PSB_APM_CMD 0x0
-#define PSB_APM_STS 0x04
-#define PSB_PWRGT_VID_ENC_MASK 0x30
-#define PSB_PWRGT_VID_DEC_MASK 0xc
-#define PSB_PWRGT_GL3_MASK 0xc0
-
-#define PSB_PM_SSC 0x20
-#define PSB_PM_SSS 0x30
-#define PSB_PWRGT_DISPLAY_MASK 0xc /*on a different BA than video/gfx*/
-#define MDFLD_PWRGT_DISPLAY_A_CNTR 0x0000000c
-#define MDFLD_PWRGT_DISPLAY_B_CNTR 0x0000c000
-#define MDFLD_PWRGT_DISPLAY_C_CNTR 0x00030000
-#define MDFLD_PWRGT_DISP_MIPI_CNTR 0x000c0000
-#define MDFLD_PWRGT_DISPLAY_CNTR (MDFLD_PWRGT_DISPLAY_A_CNTR | MDFLD_PWRGT_DISPLAY_B_CNTR | MDFLD_PWRGT_DISPLAY_C_CNTR | MDFLD_PWRGT_DISP_MIPI_CNTR)// 0x000fc00c
+#define PSB_RASTER_BLOCK 0
+#define PSB_RASTER 1
+#define PSB_RETURN 2
+#define PSB_TA 3
+
+/* Power management */
+#define PSB_PUNIT_PORT 0x04
+#define PSB_OSPMBA 0x78
+#define PSB_APMBA 0x7a
+#define PSB_APM_CMD 0x0
+#define PSB_APM_STS 0x04
+#define PSB_PWRGT_VID_ENC_MASK 0x30
+#define PSB_PWRGT_VID_DEC_MASK 0xc
+#define PSB_PWRGT_GL3_MASK 0xc0
+
+#define PSB_PM_SSC 0x20
+#define PSB_PM_SSS 0x30
+#define PSB_PWRGT_DISPLAY_MASK 0xc /*on a different BA than video/gfx*/
+#define MDFLD_PWRGT_DISPLAY_A_CNTR 0x0000000c
+#define MDFLD_PWRGT_DISPLAY_B_CNTR 0x0000c000
+#define MDFLD_PWRGT_DISPLAY_C_CNTR 0x00030000
+#define MDFLD_PWRGT_DISP_MIPI_CNTR 0x000c0000
+#define MDFLD_PWRGT_DISPLAY_CNTR (MDFLD_PWRGT_DISPLAY_A_CNTR | MDFLD_PWRGT_DISPLAY_B_CNTR | MDFLD_PWRGT_DISPLAY_C_CNTR | MDFLD_PWRGT_DISP_MIPI_CNTR) /* 0x000fc00c */
/* Display SSS register bits are different in A0 vs. B0 */
-#define PSB_PWRGT_GFX_MASK 0x3
-#define MDFLD_PWRGT_DISPLAY_A_STS 0x000000c0
-#define MDFLD_PWRGT_DISPLAY_B_STS 0x00000300
-#define MDFLD_PWRGT_DISPLAY_C_STS 0x00000c00
-#define PSB_PWRGT_GFX_MASK_B0 0xc3
+#define PSB_PWRGT_GFX_MASK 0x3
+#define MDFLD_PWRGT_DISPLAY_A_STS 0x000000c0
+#define MDFLD_PWRGT_DISPLAY_B_STS 0x00000300
+#define MDFLD_PWRGT_DISPLAY_C_STS 0x00000c00
+#define PSB_PWRGT_GFX_MASK_B0 0xc3
#define MDFLD_PWRGT_DISPLAY_A_STS_B0 0x0000000c
-#define MDFLD_PWRGT_DISPLAY_B_STS_B0 0x0000c000
-#define MDFLD_PWRGT_DISPLAY_C_STS_B0 0x00030000
-#define MDFLD_PWRGT_DISP_MIPI_STS 0x000c0000
-#define MDFLD_PWRGT_DISPLAY_STS_A0 (MDFLD_PWRGT_DISPLAY_A_STS | MDFLD_PWRGT_DISPLAY_B_STS | MDFLD_PWRGT_DISPLAY_C_STS | MDFLD_PWRGT_DISP_MIPI_STS)// 0x000fc00c
-#define MDFLD_PWRGT_DISPLAY_STS_B0 (MDFLD_PWRGT_DISPLAY_A_STS_B0 | MDFLD_PWRGT_DISPLAY_B_STS_B0 | MDFLD_PWRGT_DISPLAY_C_STS_B0 | MDFLD_PWRGT_DISP_MIPI_STS)// 0x000fc00c
+#define MDFLD_PWRGT_DISPLAY_B_STS_B0 0x0000c000
+#define MDFLD_PWRGT_DISPLAY_C_STS_B0 0x00030000
+#define MDFLD_PWRGT_DISP_MIPI_STS 0x000c0000
+#define MDFLD_PWRGT_DISPLAY_STS_A0 (MDFLD_PWRGT_DISPLAY_A_STS | MDFLD_PWRGT_DISPLAY_B_STS | MDFLD_PWRGT_DISPLAY_C_STS | MDFLD_PWRGT_DISP_MIPI_STS) /* 0x000fc00c */
+#define MDFLD_PWRGT_DISPLAY_STS_B0 (MDFLD_PWRGT_DISPLAY_A_STS_B0 | MDFLD_PWRGT_DISPLAY_B_STS_B0 | MDFLD_PWRGT_DISPLAY_C_STS_B0 | MDFLD_PWRGT_DISP_MIPI_STS) /* 0x000fc00c */
#endif
projects / platform / kernel / linux-stable.git / commitdiff