struct max6650_data {
struct i2c_client *client;
- const struct attribute_group *groups[3];
struct mutex update_lock;
int nr_fans;
bool valid; /* false until following fields are valid */
return 0;
}
-static ssize_t fan_show(struct device *dev, struct device_attribute *devattr,
- char *buf)
-{
- struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr);
- struct max6650_data *data = max6650_update_device(dev);
- int rpm;
-
- /*
- * Calculation details:
- *
- * Each tachometer counts over an interval given by the "count"
- * register (0.25, 0.5, 1 or 2 seconds). This module assumes
- * that the fans produce two pulses per revolution (this seems
- * to be the most common).
- */
-
- rpm = ((data->tach[attr->index] * 120) / DIV_FROM_REG(data->count));
- return sprintf(buf, "%d\n", rpm);
-}
-
/*
* Set the fan speed to the specified RPM (or read back the RPM setting).
* This works in closed loop mode only. Use pwm1 for open loop speed setting.
* controlled.
*/
-static ssize_t fan1_target_show(struct device *dev,
- struct device_attribute *devattr, char *buf)
-{
- struct max6650_data *data = max6650_update_device(dev);
- int kscale, ktach, rpm;
-
- /*
- * Use the datasheet equation:
- *
- * FanSpeed = KSCALE x fCLK / [256 x (KTACH + 1)]
- *
- * then multiply by 60 to give rpm.
- */
-
- kscale = DIV_FROM_REG(data->config);
- ktach = data->speed;
- rpm = 60 * kscale * clock / (256 * (ktach + 1));
- return sprintf(buf, "%d\n", rpm);
-}
-
static int max6650_set_target(struct max6650_data *data, unsigned long rpm)
{
int kscale, ktach;
data->speed);
}
-static ssize_t fan1_target_store(struct device *dev,
- struct device_attribute *devattr,
- const char *buf, size_t count)
-{
- struct max6650_data *data = dev_get_drvdata(dev);
- unsigned long rpm;
- int err;
-
- err = kstrtoul(buf, 10, &rpm);
- if (err)
- return err;
-
- mutex_lock(&data->update_lock);
-
- err = max6650_set_target(data, rpm);
-
- mutex_unlock(&data->update_lock);
-
- if (err < 0)
- return err;
-
- return count;
-}
-
-/*
- * Get/set the fan speed in open loop mode using pwm1 sysfs file.
- * Speed is given as a relative value from 0 to 255, where 255 is maximum
- * speed. Note that this is done by writing directly to the chip's DAC,
- * it won't change the closed loop speed set by fan1_target.
- * Also note that due to rounding errors it is possible that you don't read
- * back exactly the value you have set.
- */
-
-static ssize_t pwm1_show(struct device *dev, struct device_attribute *devattr,
- char *buf)
-{
- struct max6650_data *data = max6650_update_device(dev);
-
- return sprintf(buf, "%d\n", dac_to_pwm(data->dac,
- data->config & MAX6650_CFG_V12));
-}
-
-static ssize_t pwm1_store(struct device *dev,
- struct device_attribute *devattr, const char *buf,
- size_t count)
-{
- struct max6650_data *data = dev_get_drvdata(dev);
- struct i2c_client *client = data->client;
- unsigned long pwm;
- int err;
- u8 dac;
-
- err = kstrtoul(buf, 10, &pwm);
- if (err)
- return err;
-
- pwm = clamp_val(pwm, 0, 255);
-
- mutex_lock(&data->update_lock);
- dac = pwm_to_dac(pwm, data->config & MAX6650_CFG_V12);
- err = i2c_smbus_write_byte_data(client, MAX6650_REG_DAC, dac);
- if (!err)
- data->dac = dac;
- mutex_unlock(&data->update_lock);
-
- return err < 0 ? err : count;
-}
-
/*
- * Get/Set controller mode:
- * Possible values:
- * 0 = Fan always on
- * 1 = Open loop, Voltage is set according to speed, not regulated.
- * 2 = Closed loop, RPM for all fans regulated by fan1 tachometer
- * 3 = Fan off
- */
-static ssize_t pwm1_enable_show(struct device *dev,
- struct device_attribute *devattr, char *buf)
-{
- struct max6650_data *data = max6650_update_device(dev);
- int mode = (data->config & MAX6650_CFG_MODE_MASK) >> 4;
- int sysfs_modes[4] = {0, 3, 2, 1};
-
- return sprintf(buf, "%d\n", sysfs_modes[mode]);
-}
-
-static ssize_t pwm1_enable_store(struct device *dev,
- struct device_attribute *devattr,
- const char *buf, size_t count)
-{
- struct max6650_data *data = dev_get_drvdata(dev);
- unsigned long mode;
- int err;
- const u8 max6650_modes[] = {
- MAX6650_CFG_MODE_ON,
- MAX6650_CFG_MODE_OPEN_LOOP,
- MAX6650_CFG_MODE_CLOSED_LOOP,
- MAX6650_CFG_MODE_OFF,
- };
-
- err = kstrtoul(buf, 10, &mode);
- if (err)
- return err;
-
- if (mode >= ARRAY_SIZE(max6650_modes))
- return -EINVAL;
-
- mutex_lock(&data->update_lock);
-
- max6650_set_operating_mode(data, max6650_modes[mode]);
-
- mutex_unlock(&data->update_lock);
-
- return count;
-}
-
-/*
- * Read/write functions for fan1_div sysfs file. The MAX6650 has no such
- * divider. We handle this by converting between divider and counttime:
- *
- * (counttime == k) <==> (divider == 2^k), k = 0, 1, 2, or 3
- *
- * Lower values of k allow to connect a faster fan without the risk of
- * counter overflow. The price is lower resolution. You can also set counttime
- * using the module parameter. Note that the module parameter "prescaler" also
- * influences the behaviour. Unfortunately, there's no sysfs attribute
- * defined for that. See the data sheet for details.
- */
-
-static ssize_t fan1_div_show(struct device *dev,
- struct device_attribute *devattr, char *buf)
-{
- struct max6650_data *data = max6650_update_device(dev);
-
- return sprintf(buf, "%d\n", DIV_FROM_REG(data->count));
-}
-
-static ssize_t fan1_div_store(struct device *dev,
- struct device_attribute *devattr,
- const char *buf, size_t count)
-{
- struct max6650_data *data = dev_get_drvdata(dev);
- struct i2c_client *client = data->client;
- unsigned long div;
- int err;
-
- err = kstrtoul(buf, 10, &div);
- if (err)
- return err;
-
- mutex_lock(&data->update_lock);
- switch (div) {
- case 1:
- data->count = 0;
- break;
- case 2:
- data->count = 1;
- break;
- case 4:
- data->count = 2;
- break;
- case 8:
- data->count = 3;
- break;
- default:
- mutex_unlock(&data->update_lock);
- return -EINVAL;
- }
-
- i2c_smbus_write_byte_data(client, MAX6650_REG_COUNT, data->count);
- mutex_unlock(&data->update_lock);
-
- return count;
-}
-
-/*
- * Get alarm stati:
+ * Get gpio alarm status:
* Possible values:
* 0 = no alarm
* 1 = alarm
return sprintf(buf, "%d\n", alarm);
}
-static SENSOR_DEVICE_ATTR_RO(fan1_input, fan, 0);
-static SENSOR_DEVICE_ATTR_RO(fan2_input, fan, 1);
-static SENSOR_DEVICE_ATTR_RO(fan3_input, fan, 2);
-static SENSOR_DEVICE_ATTR_RO(fan4_input, fan, 3);
-static DEVICE_ATTR_RW(fan1_target);
-static DEVICE_ATTR_RW(fan1_div);
-static DEVICE_ATTR_RW(pwm1_enable);
-static DEVICE_ATTR_RW(pwm1);
-static SENSOR_DEVICE_ATTR_RO(fan1_max_alarm, alarm, MAX6650_ALRM_MAX);
-static SENSOR_DEVICE_ATTR_RO(fan1_min_alarm, alarm, MAX6650_ALRM_MIN);
-static SENSOR_DEVICE_ATTR_RO(fan1_fault, alarm, MAX6650_ALRM_TACH);
static SENSOR_DEVICE_ATTR_RO(gpio1_alarm, alarm, MAX6650_ALRM_GPIO1);
static SENSOR_DEVICE_ATTR_RO(gpio2_alarm, alarm, MAX6650_ALRM_GPIO2);
*/
devattr = container_of(a, struct device_attribute, attr);
- if (devattr == &sensor_dev_attr_fan1_max_alarm.dev_attr
- || devattr == &sensor_dev_attr_fan1_min_alarm.dev_attr
- || devattr == &sensor_dev_attr_fan1_fault.dev_attr
- || devattr == &sensor_dev_attr_gpio1_alarm.dev_attr
- || devattr == &sensor_dev_attr_gpio2_alarm.dev_attr) {
+ if (devattr == &sensor_dev_attr_gpio1_alarm.dev_attr ||
+ devattr == &sensor_dev_attr_gpio2_alarm.dev_attr) {
if (!(data->alarm_en & to_sensor_dev_attr(devattr)->index))
return 0;
}
}
static struct attribute *max6650_attrs[] = {
- &sensor_dev_attr_fan1_input.dev_attr.attr,
- &dev_attr_fan1_target.attr,
- &dev_attr_fan1_div.attr,
- &dev_attr_pwm1_enable.attr,
- &dev_attr_pwm1.attr,
- &sensor_dev_attr_fan1_max_alarm.dev_attr.attr,
- &sensor_dev_attr_fan1_min_alarm.dev_attr.attr,
- &sensor_dev_attr_fan1_fault.dev_attr.attr,
&sensor_dev_attr_gpio1_alarm.dev_attr.attr,
&sensor_dev_attr_gpio2_alarm.dev_attr.attr,
NULL
.is_visible = max6650_attrs_visible,
};
-static struct attribute *max6651_attrs[] = {
- &sensor_dev_attr_fan2_input.dev_attr.attr,
- &sensor_dev_attr_fan3_input.dev_attr.attr,
- &sensor_dev_attr_fan4_input.dev_attr.attr,
+static const struct attribute_group *max6650_groups[] = {
+ &max6650_group,
NULL
};
-static const struct attribute_group max6651_group = {
- .attrs = max6651_attrs,
-};
-
-/*
- * Real code
- */
-
static int max6650_init_client(struct max6650_data *data,
struct i2c_client *client)
{
};
#endif
+static int max6650_read(struct device *dev, enum hwmon_sensor_types type,
+ u32 attr, int channel, long *val)
+{
+ struct max6650_data *data = max6650_update_device(dev);
+ int mode;
+
+ switch (type) {
+ case hwmon_pwm:
+ switch (attr) {
+ case hwmon_pwm_input:
+ *val = dac_to_pwm(data->dac,
+ data->config & MAX6650_CFG_V12);
+ break;
+ case hwmon_pwm_enable:
+ /*
+ * Possible values:
+ * 0 = Fan always on
+ * 1 = Open loop, Voltage is set according to speed,
+ * not regulated.
+ * 2 = Closed loop, RPM for all fans regulated by fan1
+ * tachometer
+ * 3 = Fan off
+ */
+ mode = (data->config & MAX6650_CFG_MODE_MASK) >> 4;
+ *val = (4 - mode) & 3; /* {0 1 2 3} -> {0 3 2 1} */
+ break;
+ default:
+ return -EOPNOTSUPP;
+ }
+ break;
+ case hwmon_fan:
+ switch (attr) {
+ case hwmon_fan_input:
+ /*
+ * Calculation details:
+ *
+ * Each tachometer counts over an interval given by the
+ * "count" register (0.25, 0.5, 1 or 2 seconds).
+ * The driver assumes that the fans produce two pulses
+ * per revolution (this seems to be the most common).
+ */
+ *val = DIV_ROUND_CLOSEST(data->tach[channel] * 120,
+ DIV_FROM_REG(data->count));
+ break;
+ case hwmon_fan_div:
+ *val = DIV_FROM_REG(data->count);
+ break;
+ case hwmon_fan_target:
+ /*
+ * Use the datasheet equation:
+ * FanSpeed = KSCALE x fCLK / [256 x (KTACH + 1)]
+ * then multiply by 60 to give rpm.
+ */
+ *val = 60 * DIV_FROM_REG(data->config) * clock /
+ (256 * (data->speed + 1));
+ break;
+ case hwmon_fan_min_alarm:
+ *val = !!(data->alarm & MAX6650_ALRM_MIN);
+ data->alarm &= ~MAX6650_ALRM_MIN;
+ data->valid = false;
+ break;
+ case hwmon_fan_max_alarm:
+ *val = !!(data->alarm & MAX6650_ALRM_MAX);
+ data->alarm &= ~MAX6650_ALRM_MAX;
+ data->valid = false;
+ break;
+ case hwmon_fan_fault:
+ *val = !!(data->alarm & MAX6650_ALRM_TACH);
+ data->alarm &= ~MAX6650_ALRM_TACH;
+ data->valid = false;
+ break;
+ default:
+ return -EOPNOTSUPP;
+ }
+ break;
+ default:
+ return -EOPNOTSUPP;
+ }
+ return 0;
+}
+
+static const u8 max6650_pwm_modes[] = {
+ MAX6650_CFG_MODE_ON,
+ MAX6650_CFG_MODE_OPEN_LOOP,
+ MAX6650_CFG_MODE_CLOSED_LOOP,
+ MAX6650_CFG_MODE_OFF,
+};
+
+static int max6650_write(struct device *dev, enum hwmon_sensor_types type,
+ u32 attr, int channel, long val)
+{
+ struct max6650_data *data = dev_get_drvdata(dev);
+ int ret = 0;
+ u8 reg;
+
+ mutex_lock(&data->update_lock);
+
+ switch (type) {
+ case hwmon_pwm:
+ switch (attr) {
+ case hwmon_pwm_input:
+ reg = pwm_to_dac(clamp_val(val, 0, 255),
+ data->config & MAX6650_CFG_V12);
+ ret = i2c_smbus_write_byte_data(data->client,
+ MAX6650_REG_DAC, reg);
+ if (ret)
+ break;
+ data->dac = reg;
+ break;
+ case hwmon_pwm_enable:
+ if (val < 0 || val >= ARRAY_SIZE(max6650_pwm_modes)) {
+ ret = -EINVAL;
+ break;
+ }
+ ret = max6650_set_operating_mode(data,
+ max6650_pwm_modes[val]);
+ break;
+ default:
+ ret = -EOPNOTSUPP;
+ break;
+ }
+ break;
+ case hwmon_fan:
+ switch (attr) {
+ case hwmon_fan_div:
+ switch (val) {
+ case 1:
+ reg = 0;
+ break;
+ case 2:
+ reg = 1;
+ break;
+ case 4:
+ reg = 2;
+ break;
+ case 8:
+ reg = 3;
+ break;
+ default:
+ ret = -EINVAL;
+ goto error;
+ }
+ ret = i2c_smbus_write_byte_data(data->client,
+ MAX6650_REG_COUNT, reg);
+ if (ret)
+ break;
+ data->count = reg;
+ break;
+ case hwmon_fan_target:
+ if (val < 0) {
+ ret = -EINVAL;
+ break;
+ }
+ ret = max6650_set_target(data, val);
+ break;
+ default:
+ ret = -EOPNOTSUPP;
+ break;
+ }
+ break;
+ default:
+ ret = -EOPNOTSUPP;
+ break;
+ }
+
+error:
+ mutex_unlock(&data->update_lock);
+ return ret;
+}
+
+static umode_t max6650_is_visible(const void *_data,
+ enum hwmon_sensor_types type, u32 attr,
+ int channel)
+{
+ const struct max6650_data *data = _data;
+
+ if (channel && (channel >= data->nr_fans || type != hwmon_fan))
+ return 0;
+
+ switch (type) {
+ case hwmon_fan:
+ switch (attr) {
+ case hwmon_fan_input:
+ return 0444;
+ case hwmon_fan_target:
+ case hwmon_fan_div:
+ return 0644;
+ case hwmon_fan_min_alarm:
+ if (data->alarm_en & MAX6650_ALRM_MIN)
+ return 0444;
+ break;
+ case hwmon_fan_max_alarm:
+ if (data->alarm_en & MAX6650_ALRM_MAX)
+ return 0444;
+ break;
+ case hwmon_fan_fault:
+ if (data->alarm_en & MAX6650_ALRM_TACH)
+ return 0444;
+ break;
+ default:
+ break;
+ }
+ break;
+ case hwmon_pwm:
+ switch (attr) {
+ case hwmon_pwm_input:
+ case hwmon_pwm_enable:
+ return 0644;
+ default:
+ break;
+ }
+ break;
+ default:
+ break;
+ }
+ return 0;
+}
+
+static const struct hwmon_channel_info *max6650_info[] = {
+ HWMON_CHANNEL_INFO(fan, HWMON_F_INPUT | HWMON_F_TARGET | HWMON_F_DIV |
+ HWMON_F_MIN_ALARM | HWMON_F_MAX_ALARM |
+ HWMON_F_FAULT,
+ HWMON_F_INPUT, HWMON_F_INPUT, HWMON_F_INPUT),
+ HWMON_CHANNEL_INFO(pwm, HWMON_PWM_INPUT | HWMON_PWM_ENABLE),
+ NULL
+};
+
+static const struct hwmon_ops max6650_hwmon_ops = {
+ .read = max6650_read,
+ .write = max6650_write,
+ .is_visible = max6650_is_visible,
+};
+
+static const struct hwmon_chip_info max6650_chip_info = {
+ .ops = &max6650_hwmon_ops,
+ .info = max6650_info,
+};
+
static int max6650_probe(struct i2c_client *client,
const struct i2c_device_id *id)
{
if (err)
return err;
- data->groups[0] = &max6650_group;
- /* 3 additional fan inputs for the MAX6651 */
- if (data->nr_fans == 4)
- data->groups[1] = &max6651_group;
-
- hwmon_dev = devm_hwmon_device_register_with_groups(dev,
- client->name, data,
- data->groups);
+ hwmon_dev = devm_hwmon_device_register_with_info(dev,
+ client->name, data,
+ &max6650_chip_info,
+ max6650_groups);
err = PTR_ERR_OR_ZERO(hwmon_dev);
if (err)
return err;
projects / platform / kernel / linux-starfive.git / commitdiff