/* only accept EAPOL frames */
HTT_RX_IND_MPDU_STATUS_UNAUTH_PEER,
HTT_RX_IND_MPDU_STATUS_OUT_OF_SYNC,
- /* Non-data in promiscous mode */
+ /* Non-data in promiscuous mode */
HTT_RX_IND_MPDU_STATUS_MGMT_CTRL,
HTT_RX_IND_MPDU_STATUS_TKIP_MIC_ERR,
HTT_RX_IND_MPDU_STATUS_DECRYPT_ERR,
* Purpose: indicate how many 32-bit integers follow the message header
* - NUM_CHARS
* Bits 31:16
- * Purpose: indicate how many 8-bit charaters follow the series of integers
+ * Purpose: indicate how many 8-bit characters follow the series of integers
*/
struct htt_rx_test {
u8 num_ints;
/* illegal rate phy errors */
__le32 illgl_rate_phy_err;
- /* wal pdev continous xretry */
+ /* wal pdev continuous xretry */
__le32 pdev_cont_xretry;
- /* wal pdev continous xretry */
+ /* wal pdev continuous xretry */
__le32 pdev_tx_timeout;
/* wal pdev resets */
* type.
*
* 6. Comment each parameter part of the WMI command/event structure by
- * using the 2 stars at the begining of C comment instead of one star to
+ * using the 2 stars at the beginning of C comment instead of one star to
* enable HTML document generation using Doxygen.
*
*/
* In offload mode target supports features like WOW, chatter and
* other protocol offloads. In order to support them some
* functionalities like reorder buffering, PN checking need to be
- * done in target. This determines maximum number of peers suported
+ * done in target. This determines maximum number of peers supported
* by target in offload mode
*/
__le32 num_offload_peers;
* Max. number of Tx fragments per MSDU
* This parameter controls the max number of Tx fragments per MSDU.
* This is sent by the target as part of the WMI_SERVICE_READY event
- * and is overriden by the OS shim as required.
+ * and is overridden by the OS shim as required.
*/
__le32 max_frag_entries;
} __packed;
* Max. number of Tx fragments per MSDU
* This parameter controls the max number of Tx fragments per MSDU.
* This is sent by the target as part of the WMI_SERVICE_READY event
- * and is overriden by the OS shim as required.
+ * and is overridden by the OS shim as required.
*/
__le32 max_frag_entries;
} __packed;
struct wmi_host_mem_chunks mem_chunks;
} __packed;
-/* _10x stucture is from 10.X FW API */
+/* _10x structure is from 10.X FW API */
struct wmi_init_cmd_10x {
struct wmi_resource_config_10x resource_config;
struct wmi_host_mem_chunks mem_chunks;
/* illegal rate phy errors */
__le32 illgl_rate_phy_err;
- /* wal pdev continous xretry */
+ /* wal pdev continuous xretry */
__le32 pdev_cont_xretry;
/* wal pdev continous xretry */
__le32 flags;
/* ssid field. Only valid for AP/GO/IBSS/BTAmp VDEV type. */
struct wmi_ssid ssid;
- /* beacon/probe reponse xmit rate. Applicable for SoftAP. */
+ /* beacon/probe response xmit rate. Applicable for SoftAP. */
__le32 bcn_tx_rate;
- /* beacon/probe reponse xmit power. Applicable for SoftAP. */
+ /* beacon/probe response xmit power. Applicable for SoftAP. */
__le32 bcn_tx_power;
/* number of p2p NOA descriptor(s) from scan entry */
__le32 num_noa_descriptors;
WMI_VDEV_PARAM_BEACON_INTERVAL,
/* Listen interval in TUs */
WMI_VDEV_PARAM_LISTEN_INTERVAL,
- /* muticast rate in Mbps */
+ /* multicast rate in Mbps */
WMI_VDEV_PARAM_MULTICAST_RATE,
/* management frame rate in Mbps */
WMI_VDEV_PARAM_MGMT_TX_RATE,
WMI_10X_VDEV_PARAM_BEACON_INTERVAL,
/* Listen interval in TUs */
WMI_10X_VDEV_PARAM_LISTEN_INTERVAL,
- /* muticast rate in Mbps */
+ /* multicast rate in Mbps */
WMI_10X_VDEV_PARAM_MULTICAST_RATE,
/* management frame rate in Mbps */
WMI_10X_VDEV_PARAM_MGMT_TX_RATE,
} __packed;
/* VDEV start response status codes */
-/* VDEV succesfully started */
+/* VDEV successfully started */
#define WMI_INIFIED_VDEV_START_RESPONSE_STATUS_SUCCESS 0x0
/* requested VDEV not found */
#define WMI_UAPSD_AC_TYPE_TRIG 1
#define WMI_UAPSD_AC_BIT_MASK(ac, type) \
- ((type == WMI_UAPSD_AC_TYPE_DELI) ? (1 << (ac << 1)) : (1 << ((ac << 1) + 1)))
+ (type == WMI_UAPSD_AC_TYPE_DELI ? 1 << (ac << 1) : 1 << ((ac << 1) + 1))
enum wmi_sta_ps_param_uapsd {
WMI_STA_PS_UAPSD_AC0_DELIVERY_EN = (1 << 0),