// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
/*
- * Device Tree file for CRS305-1G-4S board
+ * Device Tree file for MikroTik CRS305-1G-4S+ board
*
- * Copyright (C) 2016 Allied Telesis Labs
- *
- * Based on armada-xp-db.dts
- *
- * Note: this Device Tree assumes that the bootloader has remapped the
- * internal registers to 0xf1000000 (instead of the default
- * 0xd0000000). The 0xf1000000 is the default used by the recent,
- * DT-capable, U-Boot bootloaders provided by Marvell. Some earlier
- * boards were delivered with an older version of the bootloader that
- * left internal registers mapped at 0xd0000000. If you are in this
- * situation, you should either update your bootloader (preferred
- * solution) or the below Device Tree should be adjusted.
+ * Copyright (C) 2020 Sartura Ltd.
+ * Author: Luka Kovacic <luka.kovacic@sartura.hr>
*/
-/dts-v1/;
-#include "armada-xp-98dx3236.dtsi"
-#include "armada-xp-crs305-1g-4s-u-boot.dtsi"
+#include "armada-xp-crs305-1g-4s.dtsi"
/ {
- model = "CRS305-1G-4S";
- compatible = "marvell,armadaxp-98dx3236", "marvell,armadaxp-mv78260", "marvell,armadaxp", "marvell,armada-370-xp";
-
- chosen {
- stdout-path = "serial0:115200n8";
- bootargs = "console=ttyS0,115200 earlyprintk";
- };
-
- aliases {
- spi0 = &spi0;
- };
-
- memory {
- device_type = "memory";
- reg = <0 0x00000000 0 0x20000000>; /* 512 MB */
- };
-};
-
-&L2 {
- arm,parity-enable;
- marvell,ecc-enable;
-};
-
-&devbus_bootcs {
- status = "okay";
-
- /* Device Bus parameters are required */
-
- /* Read parameters */
- devbus,bus-width = <16>;
- devbus,turn-off-ps = <60000>;
- devbus,badr-skew-ps = <0>;
- devbus,acc-first-ps = <124000>;
- devbus,acc-next-ps = <248000>;
- devbus,rd-setup-ps = <0>;
- devbus,rd-hold-ps = <0>;
-
- /* Write parameters */
- devbus,sync-enable = <0>;
- devbus,wr-high-ps = <60000>;
- devbus,wr-low-ps = <60000>;
- devbus,ale-wr-ps = <60000>;
-};
-
-&uart0 {
- status = "okay";
-};
-
-&uart1 {
- status = "okay";
-};
-
-&i2c0 {
- clock-frequency = <100000>;
- status = "okay";
-};
-
-&usb0 {
- status = "okay";
+ model = "MikroTik CRS305-1G-4S+";
};
&spi0 {
status = "okay";
-
- spi-flash@0 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "spi-flash", "jedec,spi-nor";
- reg = <0>; /* Chip select 0 */
- spi-max-frequency = <108000000>;
- m25p,fast-read;
-
- partition@u-boot {
- reg = <0x00000000 0x00100000>;
- label = "u-boot";
- };
- partition@u-boot-env {
- reg = <0x00100000 0x00040000>;
- label = "u-boot-env";
- };
- partition@unused {
- reg = <0x00140000 0x00ec0000>;
- label = "unused";
- };
-
- };
};
--- /dev/null
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Device Tree file for CRS305-1G-4S board
+ *
+ * Copyright (C) 2016 Allied Telesis Labs
+ * Copyright (C) 2020 Sartura Ltd.
+ *
+ * Based on armada-xp-db.dts
+ *
+ * Note: this Device Tree assumes that the bootloader has remapped the
+ * internal registers to 0xf1000000 (instead of the default
+ * 0xd0000000). The 0xf1000000 is the default used by the recent,
+ * DT-capable, U-Boot bootloaders provided by Marvell. Some earlier
+ * boards were delivered with an older version of the bootloader that
+ * left internal registers mapped at 0xd0000000. If you are in this
+ * situation, you should either update your bootloader (preferred
+ * solution) or the below Device Tree should be adjusted.
+ */
+
+/dts-v1/;
+#include "armada-xp-98dx3236.dtsi"
+#include "armada-xp-crs305-1g-4s-u-boot.dtsi"
+
+/ {
+ model = "CRS305-1G-4S+";
+ compatible = "marvell,armadaxp-98dx3236", "marvell,armadaxp-mv78260", "marvell,armadaxp", "marvell,armada-370-xp";
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ bootargs = "console=ttyS0,115200 earlyprintk";
+ };
+
+ aliases {
+ spi0 = &spi0;
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0 0x00000000 0 0x20000000>; /* 512 MB */
+ };
+};
+
+&L2 {
+ arm,parity-enable;
+ marvell,ecc-enable;
+};
+
+&devbus_bootcs {
+ status = "okay";
+
+ /* Device Bus parameters are required */
+
+ /* Read parameters */
+ devbus,bus-width = <16>;
+ devbus,turn-off-ps = <60000>;
+ devbus,badr-skew-ps = <0>;
+ devbus,acc-first-ps = <124000>;
+ devbus,acc-next-ps = <248000>;
+ devbus,rd-setup-ps = <0>;
+ devbus,rd-hold-ps = <0>;
+
+ /* Write parameters */
+ devbus,sync-enable = <0>;
+ devbus,wr-high-ps = <60000>;
+ devbus,wr-low-ps = <60000>;
+ devbus,ale-wr-ps = <60000>;
+};
+
+&uart0 {
+ status = "okay";
+};
+
+&uart1 {
+ status = "okay";
+};
+
+&i2c0 {
+ clock-frequency = <100000>;
+ status = "okay";
+};
+
+&usb0 {
+ status = "okay";
+};
+
+&spi0 {
+ status = "okay";
+
+ spi-flash@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "spi-flash", "jedec,spi-nor";
+ reg = <0>; /* Chip select 0 */
+ spi-max-frequency = <108000000>;
+ m25p,fast-read;
+
+ partition@u-boot {
+ reg = <0x00000000 0x00080000>;
+ label = "u-boot";
+ };
+ partition@u-boot-env {
+ reg = <0x00080000 0x00010000>;
+ label = "u-boot-env";
+ };
+ partition@firmware {
+ reg = <0x00090000 0x00f70000>;
+ label = "firmware";
+ };
+
+ };
+};
bool "Support DB-XC3-24G4XG"
select 98DX3336
-config TARGET_CRS305_1G_4S
- bool "Support CRS305-1G-4S"
+config TARGET_CRS3XX_98DX3236
+ bool "Support CRS3XX-98DX3236"
select 98DX3236
endchoice
default "a38x" if TARGET_CONTROLCENTERDC
default "x530" if TARGET_X530
default "db-xc3-24g4xg" if TARGET_DB_XC3_24G4XG
- default "crs305-1g-4s" if TARGET_CRS305_1G_4S
+ default "crs3xx-98dx3236" if TARGET_CRS3XX_98DX3236
config SYS_CONFIG_NAME
default "clearfog" if TARGET_CLEARFOG
default "controlcenterdc" if TARGET_CONTROLCENTERDC
default "x530" if TARGET_X530
default "db-xc3-24g4xg" if TARGET_DB_XC3_24G4XG
- default "crs305-1g-4s" if TARGET_CRS305_1G_4S
+ default "crs3xx-98dx3236" if TARGET_CRS3XX_98DX3236
config SYS_VENDOR
default "Marvell" if TARGET_DB_MV784MP_GP
default "CZ.NIC" if TARGET_TURRIS_MOX
default "gdsys" if TARGET_CONTROLCENTERDC
default "alliedtelesis" if TARGET_X530
- default "mikrotik" if TARGET_CRS305_1G_4S
+ default "mikrotik" if TARGET_CRS3XX_98DX3236
config SYS_SOC
default "mvebu"
+++ /dev/null
-CRS305-1G-4S BOARD
-M: Luka Kovacic <me@lukakovacic.xyz>
-S: Maintained
-F: board/mikrotik/crs305-1g-4s/
-F: include/configs/crs305-1g-4s.h
-F: configs/crs305-1g-4s_defconfig
-F: arch/arm/dts/armada-xp-crs305-1g-4s.dts
--- /dev/null
+CRS3XX-98DX3236 BOARD
+M: Luka Kovacic <luka.kovacic@sartura.hr>
+S: Maintained
+F: board/mikrotik/crs3xx-98dx3236/
+F: include/configs/crs3xx-98dx3236.h
+
+CRS305-1G-4S BOARD
+M: Luka Kovacic <luka.kovacic@sartura.hr>
+S: Maintained
+F: configs/crs305-1g-4s_defconfig
+F: arch/arm/dts/armada-xp-crs305-1g-4s.dts
#
# Copyright (C) 2015 Stefan Roese <sr@denx.de>
-obj-y := crs305-1g-4s.o
+obj-y := crs3xx-98dx3236.o
extra-y := kwbimage.cfg
quiet_cmd_sed = SED $@
-MikroTik CRS305-1G-4S+IN
+MikroTik CRS3XX-98DX3236
========================
-CRS305-1G-4S+IN is a 4x SFP+ switch with a Gigabit Ethernet port for management.
-Specifications:
+CRS3XX-98DX3236 is a U-Boot port that supports a series of MikroTik switches
+based on the Marvell Prestera 98DX3236 switch with an integrated CPU.
+
+Common specifications:
- Marvell Prestera 98DX3236 switch with an integrated ARMv7 CPU
- 512 MB DDR3 RAM
- UART @ 115200bps
- - 4x SFP+
- - Gigabit Ethernet (AR8033)
- 16 MB SPI flash (Winbond 25Q128JVSM)
Currently supported hardware:
- SPI boot, environment and load kernel
Planned:
- - Gigabit Ethernet support
+ - Gigabit Ethernet support (internal CPU <-> switch fabric connection)
Getting binary.0
================
BOOT_FROM spi
# Binary Header (bin_hdr) with DDR3 training code
-BINARY board/mikrotik/crs305-1g-4s/binary.0 0000005b 00000068
+BINARY board/mikrotik/crs3xx-98dx3236/binary.0 0000005b 00000068
CONFIG_ARCH_MVEBU=y
CONFIG_SYS_TEXT_BASE=0x00800000
CONFIG_SYS_MALLOC_F_LEN=0x2000
-CONFIG_TARGET_CRS305_1G_4S=y
+CONFIG_TARGET_CRS3XX_98DX3236=y
CONFIG_ENV_SIZE=0x10000
-CONFIG_ENV_OFFSET=0x100000
-CONFIG_ENV_SECT_SIZE=0x40000
+CONFIG_ENV_SECT_SIZE=0x10000
+CONFIG_ENV_OFFSET=0x80000
+# CONFIG_EFI_LOADER is not set
CONFIG_BUILD_TARGET="u-boot.kwb"
CONFIG_USE_PREBOOT=y
CONFIG_SYS_CONSOLE_INFO_QUIET=y
+CONFIG_AUTOBOOT_KEYED=y
+CONFIG_AUTOBOOT_PROMPT="Autoboot in %d seconds, to stop use 's' key\n"
+CONFIG_AUTOBOOT_STOP_STR="s"
+CONFIG_AUTOBOOT_KEYED_CTRLC=y
CONFIG_CMD_BOOTZ=y
-CONFIG_CMD_MEMTEST=y
-CONFIG_SYS_ALT_MEMTEST=y
-CONFIG_SYS_MEMTEST_START=0x00800000
-CONFIG_SYS_MEMTEST_END=0x00ffffff
# CONFIG_CMD_FLASH is not set
-CONFIG_CMD_I2C=y
+# CONFIG_CMD_I2C is not set
CONFIG_CMD_SPI=y
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_TFTPPUT=y
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
CONFIG_CMD_CACHE=y
-CONFIG_CMD_TIME=y
-CONFIG_CMD_EXT2=y
-CONFIG_CMD_EXT4=y
-CONFIG_CMD_FAT=y
-CONFIG_CMD_FS_GENERIC=y
-CONFIG_CMD_UBI=y
+# CONFIG_CMD_UBI is not set
+CONFIG_CMD_MTD=y
+CONFIG_CMD_MTDPARTS=y
CONFIG_DEFAULT_DEVICE_TREE="armada-xp-crs305-1g-4s"
CONFIG_ENV_IS_IN_SPI_FLASH=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_BLK=y
-CONFIG_DM_I2C=y
-CONFIG_SYS_I2C_MVTWSI=y
+# CONFIG_DM_I2C is not set
+# CONFIG_SYS_I2C_MVTWSI is not set
# CONFIG_MMC is not set
CONFIG_MTD=y
+CONFIG_MTD_PARTITIONS=y
CONFIG_DM_MTD=y
+CONFIG_DM_SPI_FLASH=y
+CONFIG_SPI_FLASH_MTD=y
CONFIG_SPI_FLASH_SFDP_SUPPORT=y
-CONFIG_SPI_FLASH_MACRONIX=y
-CONFIG_SPI_FLASH_STMICRO=y
-CONFIG_SPI_FLASH_SST=y
+CONFIG_SPI_FLASH_BAR=y
CONFIG_SPI_FLASH_WINBOND=y
# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set
+CONFIG_FIT=y
+CONFIG_FIT_ENABLE_SHA256_SUPPORT=y
+CONFIG_FIT_VERBOSE=y
+CONFIG_FIT_BEST_MATCH=y
CONFIG_PCI=y
CONFIG_PCI_MVEBU=y
CONFIG_SYS_NS16550=y
* Copyright (C) 2014 Stefan Roese <sr@denx.de>
*/
-#ifndef _CONFIG_CRS305_1G_4S_H
-#define _CONFIG_CRS305_1G_4S_H
+#ifndef _CONFIG_CRS3XX_98DX3236_H
+#define _CONFIG_CRS3XX_98DX3236_H
/*
* High Level Configuration Options (easy to change)
#undef CONFIG_SYS_MAXARGS
#define CONFIG_SYS_MAXARGS 96
-#endif /* _CONFIG_CRS305_1G_4S_H */
+#endif /* _CONFIG_CRS3XX_98DX3236_H */
projects / platform / kernel / u-boot.git / commitdiff