m68k/mac: Fix unexpected interrupt with CONFIG_EARLY_PRINTK

The present code does not wait for the SCC to finish resetting itself
before trying to initialise the device. The result is that the SCC
interrupt sources become enabled (if they weren't already). This leads to
an early boot crash (unexpected interrupt) given CONFIG_EARLY_PRINTK. Fix
this by adding a delay. A successful reset disables the interrupt sources.

Also, after the reset for channel A setup, the SCC then gets a second
reset for channel B setup which leaves channel A uninitialised again. Fix
this by performing the reset only once.

Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Cc: stable@vger.kernel.org
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>

diff --git a/arch/m68k/kernel/head.S b/arch/m68k/kernel/head.S
index d197e7f..ac85f16 100644 (file)
--- a/arch/m68k/kernel/head.S
+++ b/arch/m68k/kernel/head.S
@@ -2752,11 +2752,9 @@ func_return      get_new_page
 #ifdef CONFIG_MAC
 
 L(scc_initable_mac):
-       .byte   9,12            /* Reset */
        .byte   4,0x44          /* x16, 1 stopbit, no parity */
        .byte   3,0xc0          /* receiver: 8 bpc */
        .byte   5,0xe2          /* transmitter: 8 bpc, assert dtr/rts */
-       .byte   9,0             /* no interrupts */
        .byte   10,0            /* NRZ */
        .byte   11,0x50         /* use baud rate generator */
        .byte   12,1,13,0       /* 38400 baud */
@@ -2899,6 +2897,7 @@ func_start        serial_init,%d0/%d1/%a0/%a1
        is_not_mac(L(serial_init_not_mac))
 
 #ifdef SERIAL_DEBUG
+
 /* You may define either or both of these. */
 #define MAC_USE_SCC_A /* Modem port */
 #define MAC_USE_SCC_B /* Printer port */
@@ -2908,9 +2907,21 @@ func_start       serial_init,%d0/%d1/%a0/%a1
 #define mac_scc_cha_b_data_offset      0x4
 #define mac_scc_cha_a_data_offset      0x6
 
+#if defined(MAC_USE_SCC_A) || defined(MAC_USE_SCC_B)
+       movel   %pc@(L(mac_sccbase)),%a0
+       /* Reset SCC device */
+       moveb   #9,%a0@(mac_scc_cha_a_ctrl_offset)
+       moveb   #0xc0,%a0@(mac_scc_cha_a_ctrl_offset)
+       /* Wait for 5 PCLK cycles, which is about 68 CPU cycles */
+       /* 5 / 3.6864 MHz = approx. 1.36 us = 68 / 50 MHz */
+       movel   #35,%d0
+5:
+       subq    #1,%d0
+       jne     5b
+#endif
+
 #ifdef MAC_USE_SCC_A
        /* Initialize channel A */
-       movel   %pc@(L(mac_sccbase)),%a0
        lea     %pc@(L(scc_initable_mac)),%a1
 5:     moveb   %a1@+,%d0
        jmi     6f
@@ -2922,9 +2933,6 @@ func_start        serial_init,%d0/%d1/%a0/%a1
 
 #ifdef MAC_USE_SCC_B
        /* Initialize channel B */
-#ifndef MAC_USE_SCC_A  /* Load mac_sccbase only if needed */
-       movel   %pc@(L(mac_sccbase)),%a0
-#endif /* MAC_USE_SCC_A */
        lea     %pc@(L(scc_initable_mac)),%a1
 7:     moveb   %a1@+,%d0
        jmi     8f
@@ -2933,6 +2941,7 @@ func_start        serial_init,%d0/%d1/%a0/%a1
        jra     7b
 8:
 #endif /* MAC_USE_SCC_B */
+
 #endif /* SERIAL_DEBUG */
 
        jra     L(serial_init_done)
@@ -3006,17 +3015,17 @@ func_start      serial_putc,%d0/%d1/%a0/%a1
 
 #ifdef SERIAL_DEBUG
 
-#ifdef MAC_USE_SCC_A
+#if defined(MAC_USE_SCC_A) || defined(MAC_USE_SCC_B)
        movel   %pc@(L(mac_sccbase)),%a1
+#endif
+
+#ifdef MAC_USE_SCC_A
 3:     btst    #2,%a1@(mac_scc_cha_a_ctrl_offset)
        jeq     3b
        moveb   %d0,%a1@(mac_scc_cha_a_data_offset)
 #endif /* MAC_USE_SCC_A */
 
 #ifdef MAC_USE_SCC_B
-#ifndef MAC_USE_SCC_A  /* Load mac_sccbase only if needed */
-       movel   %pc@(L(mac_sccbase)),%a1
-#endif /* MAC_USE_SCC_A */
 4:     btst    #2,%a1@(mac_scc_cha_b_ctrl_offset)
        jeq     4b
        moveb   %d0,%a1@(mac_scc_cha_b_data_offset)