struct rx_sw_desc *sdesc; /* address of SW Rx descriptor ring */
__be64 *desc; /* address of HW Rx descriptor ring */
dma_addr_t addr; /* bus address of HW ring start */
- u64 udb; /* BAR2 offset of User Doorbell area */
+ void __iomem *bar2_addr; /* address of BAR2 Queue registers */
+ unsigned int bar2_qid; /* Queue ID for BAR2 Queue registers */
};
/* A packet gather list */
u16 abs_id; /* absolute SGE id for the response q */
__be64 *desc; /* address of HW response ring */
dma_addr_t phys_addr; /* physical address of the ring */
- u64 udb; /* BAR2 offset of User Doorbell area */
+ void __iomem *bar2_addr; /* address of BAR2 Queue registers */
+ unsigned int bar2_qid; /* Queue ID for BAR2 Queue registers */
unsigned int iqe_len; /* entry size */
unsigned int size; /* capacity of response queue */
struct adapter *adap;
int db_disabled;
unsigned short db_pidx;
unsigned short db_pidx_inc;
- u64 udb; /* BAR2 offset of User Doorbell area */
+ void __iomem *bar2_addr; /* address of BAR2 Queue registers */
+ unsigned int bar2_qid; /* Queue ID for BAR2 Queue registers */
};
struct sge_eth_txq { /* state for an SGE Ethernet Tx queue */
}
EXPORT_SYMBOL(cxgb4_read_sge_timestamp);
+int cxgb4_bar2_sge_qregs(struct net_device *dev,
+ unsigned int qid,
+ enum cxgb4_bar2_qtype qtype,
+ u64 *pbar2_qoffset,
+ unsigned int *pbar2_qid)
+{
+ return t4_bar2_sge_qregs(netdev2adap(dev),
+ qid,
+ (qtype == CXGB4_BAR2_QTYPE_EGRESS
+ ? T4_BAR2_QTYPE_EGRESS
+ : T4_BAR2_QTYPE_INGRESS),
+ pbar2_qoffset,
+ pbar2_qid);
+}
+EXPORT_SYMBOL(cxgb4_bar2_sge_qregs);
+
static struct pci_driver cxgb4_driver;
static void check_neigh_update(struct neighbour *neigh)
u32 dropped_db = t4_read_reg(adap, 0x010ac);
u16 qid = (dropped_db >> 15) & 0x1ffff;
u16 pidx_inc = dropped_db & 0x1fff;
- unsigned int s_qpp;
- unsigned short udb_density;
- unsigned long qpshift;
- int page;
- u32 udb;
-
- dev_warn(adap->pdev_dev,
- "Dropped DB 0x%x qid %d bar2 %d coalesce %d pidx %d\n",
- dropped_db, qid,
- (dropped_db >> 14) & 1,
- (dropped_db >> 13) & 1,
- pidx_inc);
-
- drain_db_fifo(adap, 1);
+ u64 bar2_qoffset;
+ unsigned int bar2_qid;
+ int ret;
- s_qpp = QUEUESPERPAGEPF1 * adap->fn;
- udb_density = 1 << QUEUESPERPAGEPF0_GET(t4_read_reg(adap,
- SGE_EGRESS_QUEUES_PER_PAGE_PF) >> s_qpp);
- qpshift = PAGE_SHIFT - ilog2(udb_density);
- udb = qid << qpshift;
- udb &= PAGE_MASK;
- page = udb / PAGE_SIZE;
- udb += (qid - (page * udb_density)) * 128;
-
- writel(PIDX(pidx_inc), adap->bar2 + udb + 8);
+ ret = t4_bar2_sge_qregs(adap, qid, T4_BAR2_QTYPE_EGRESS,
+ &bar2_qoffset, &bar2_qid);
+ if (ret)
+ dev_err(adap->pdev_dev, "doorbell drop recovery: "
+ "qid=%d, pidx_inc=%d\n", qid, pidx_inc);
+ else
+ writel(PIDX_T5(pidx_inc) | QID(bar2_qid),
+ adap->bar2 + bar2_qoffset + SGE_UDB_KDOORBELL);
/* Re-enable BAR2 WC */
t4_set_reg_field(adap, 0x10b0, 1<<15, 1<<15);
lli.adapter_type = adap->params.chip;
lli.iscsi_iolen = MAXRXDATA_GET(t4_read_reg(adap, TP_PARA_REG2));
lli.cclk_ps = 1000000000 / adap->params.vpd.cclk;
- lli.udb_density = 1 << QUEUESPERPAGEPF0_GET(
- t4_read_reg(adap, SGE_EGRESS_QUEUES_PER_PAGE_PF) >>
- (adap->fn * 4));
- lli.ucq_density = 1 << QUEUESPERPAGEPF0_GET(
- t4_read_reg(adap, SGE_INGRESS_QUEUES_PER_PAGE_PF) >>
- (adap->fn * 4));
+ lli.udb_density = 1 << adap->params.sge.eq_qpp;
+ lli.ucq_density = 1 << adap->params.sge.iq_qpp;
lli.filt_mode = adap->params.tp.vlan_pri_map;
/* MODQ_REQ_MAP sets queues 0-3 to chan 0-3 */
for (i = 0; i < NCHAN; i++)
t4_load_mtus(adap, adap->params.mtus, adap->params.a_wnd,
adap->params.b_wnd);
}
+ t4_init_sge_params(adap);
t4_init_tp_params(adap);
adap->flags |= FW_OK;
return 0;
int cxgb4_read_tpte(struct net_device *dev, u32 stag, __be32 *tpte);
u64 cxgb4_read_sge_timestamp(struct net_device *dev);
+enum cxgb4_bar2_qtype { CXGB4_BAR2_QTYPE_EGRESS, CXGB4_BAR2_QTYPE_INGRESS };
+int cxgb4_bar2_sge_qregs(struct net_device *dev,
+ unsigned int qid,
+ enum cxgb4_bar2_qtype qtype,
+ u64 *pbar2_qoffset,
+ unsigned int *pbar2_qid);
+
#endif /* !__CXGB4_OFLD_H */
val |= DBPRIO(1);
wmb();
- /* If we're on T4, use the old doorbell mechanism; otherwise
- * use the new BAR2 mechanism.
+ /* If we don't have access to the new User Doorbell (T5+), use
+ * the old doorbell mechanism; otherwise use the new BAR2
+ * mechanism.
*/
- if (is_t4(adap->params.chip)) {
+ if (unlikely(q->bar2_addr == NULL)) {
t4_write_reg(adap, MYPF_REG(SGE_PF_KDOORBELL),
val | QID(q->cntxt_id));
} else {
- writel(val, adap->bar2 + q->udb + SGE_UDB_KDOORBELL);
+ writel(val | QID(q->bar2_qid),
+ q->bar2_addr + SGE_UDB_KDOORBELL);
/* This Write memory Barrier will force the write to
* the User Doorbell area to be flushed.
*end = 0;
}
-/* This function copies a tx_desc struct to memory mapped BAR2 space(user space
- * writes). For coalesced WR SGE, fetches data from the FIFO instead of from
- * Host.
+/* This function copies 64 byte coalesced work request to
+ * memory mapped BAR2 space. For coalesced WR SGE fetches
+ * data from the FIFO instead of from Host.
*/
-static void cxgb_pio_copy(u64 __iomem *dst, struct tx_desc *desc)
+static void cxgb_pio_copy(u64 __iomem *dst, u64 *src)
{
- int count = sizeof(*desc) / sizeof(u64);
- u64 *src = (u64 *)desc;
+ int count = 8;
while (count) {
writeq(*src, dst);
{
wmb(); /* write descriptors before telling HW */
- if (is_t4(adap->params.chip)) {
+ /* If we don't have access to the new User Doorbell (T5+), use the old
+ * doorbell mechanism; otherwise use the new BAR2 mechanism.
+ */
+ if (unlikely(q->bar2_addr == NULL)) {
u32 val = PIDX(n);
unsigned long flags;
*/
WARN_ON(val & DBPRIO(1));
- /* For T5 and later we use the Write-Combine mapped BAR2 User
- * Doorbell mechanism. If we're only writing a single TX
- * Descriptor and TX Write Combining hasn't been disabled, we
- * can use the Write Combining Gather Buffer; otherwise we use
- * the simple doorbell.
+ /* If we're only writing a single TX Descriptor and we can use
+ * Inferred QID registers, we can use the Write Combining
+ * Gather Buffer; otherwise we use the simple doorbell.
*/
- if (n == 1) {
+ if (n == 1 && q->bar2_qid == 0) {
int index = (q->pidx
? (q->pidx - 1)
: (q->size - 1));
+ u64 *wr = (u64 *)&q->desc[index];
- cxgb_pio_copy(adap->bar2 + q->udb + SGE_UDB_WCDOORBELL,
- q->desc + index);
+ cxgb_pio_copy((u64 __iomem *)
+ (q->bar2_addr + SGE_UDB_WCDOORBELL),
+ wr);
} else {
- writel(val, adap->bar2 + q->udb + SGE_UDB_KDOORBELL);
+ writel(val | QID(q->bar2_qid),
+ q->bar2_addr + SGE_UDB_KDOORBELL);
}
/* This Write Memory Barrier will force the write to the User
params = QINTR_TIMER_IDX(7);
val = CIDXINC(work_done) | SEINTARM(params);
- if (is_t4(q->adap->params.chip)) {
+
+ /* If we don't have access to the new User GTS (T5+), use the old
+ * doorbell mechanism; otherwise use the new BAR2 mechanism.
+ */
+ if (unlikely(q->bar2_addr == NULL)) {
t4_write_reg(q->adap, MYPF_REG(SGE_PF_GTS),
val | INGRESSQID((u32)q->cntxt_id));
} else {
- writel(val, q->adap->bar2 + q->udb + SGE_UDB_GTS);
+ writel(val | INGRESSQID(q->bar2_qid),
+ q->bar2_addr + SGE_UDB_GTS);
wmb();
}
return work_done;
}
val = CIDXINC(credits) | SEINTARM(q->intr_params);
- if (is_t4(adap->params.chip)) {
+
+ /* If we don't have access to the new User GTS (T5+), use the old
+ * doorbell mechanism; otherwise use the new BAR2 mechanism.
+ */
+ if (unlikely(q->bar2_addr == NULL)) {
t4_write_reg(adap, MYPF_REG(SGE_PF_GTS),
val | INGRESSQID(q->cntxt_id));
} else {
- writel(val, adap->bar2 + q->udb + SGE_UDB_GTS);
+ writel(val | INGRESSQID(q->bar2_qid),
+ q->bar2_addr + SGE_UDB_GTS);
wmb();
}
spin_unlock(&adap->sge.intrq_lock);
}
/**
- * udb_address - return the BAR2 User Doorbell address for a Queue
- * @adap: the adapter
- * @cntxt_id: the Queue Context ID
- * @qpp: Queues Per Page (for all PFs)
+ * bar2_address - return the BAR2 address for an SGE Queue's Registers
+ * @adapter: the adapter
+ * @qid: the SGE Queue ID
+ * @qtype: the SGE Queue Type (Egress or Ingress)
+ * @pbar2_qid: BAR2 Queue ID or 0 for Queue ID inferred SGE Queues
*
- * Returns the BAR2 address of the user Doorbell associated with the
- * indicated Queue Context ID. Note that this is only applicable
- * for T5 and later.
- */
-static u64 udb_address(struct adapter *adap, unsigned int cntxt_id,
- unsigned int qpp)
-{
- u64 udb;
- unsigned int s_qpp;
- unsigned short udb_density;
- unsigned long qpshift;
- int page;
-
- BUG_ON(is_t4(adap->params.chip));
-
- s_qpp = (QUEUESPERPAGEPF0 +
- (QUEUESPERPAGEPF1 - QUEUESPERPAGEPF0) * adap->fn);
- udb_density = 1 << ((qpp >> s_qpp) & QUEUESPERPAGEPF0_MASK);
- qpshift = PAGE_SHIFT - ilog2(udb_density);
- udb = (u64)cntxt_id << qpshift;
- udb &= PAGE_MASK;
- page = udb / PAGE_SIZE;
- udb += (cntxt_id - (page * udb_density)) * SGE_UDB_SIZE;
-
- return udb;
-}
+ * Returns the BAR2 address for the SGE Queue Registers associated with
+ * @qid. If BAR2 SGE Registers aren't available, returns NULL. Also
+ * returns the BAR2 Queue ID to be used with writes to the BAR2 SGE
+ * Queue Registers. If the BAR2 Queue ID is 0, then "Inferred Queue ID"
+ * Registers are supported (e.g. the Write Combining Doorbell Buffer).
+ */
+static void __iomem *bar2_address(struct adapter *adapter,
+ unsigned int qid,
+ enum t4_bar2_qtype qtype,
+ unsigned int *pbar2_qid)
+{
+ u64 bar2_qoffset;
+ int ret;
-static u64 udb_address_eq(struct adapter *adap, unsigned int cntxt_id)
-{
- return udb_address(adap, cntxt_id,
- t4_read_reg(adap, SGE_EGRESS_QUEUES_PER_PAGE_PF));
-}
+ ret = t4_bar2_sge_qregs(adapter, qid, qtype,
+ &bar2_qoffset, pbar2_qid);
+ if (ret)
+ return NULL;
-static u64 udb_address_iq(struct adapter *adap, unsigned int cntxt_id)
-{
- return udb_address(adap, cntxt_id,
- t4_read_reg(adap, SGE_INGRESS_QUEUES_PER_PAGE_PF));
+ return adapter->bar2 + bar2_qoffset;
}
int t4_sge_alloc_rxq(struct adapter *adap, struct sge_rspq *iq, bool fwevtq,
iq->next_intr_params = iq->intr_params;
iq->cntxt_id = ntohs(c.iqid);
iq->abs_id = ntohs(c.physiqid);
- if (!is_t4(adap->params.chip))
- iq->udb = udb_address_iq(adap, iq->cntxt_id);
+ iq->bar2_addr = bar2_address(adap,
+ iq->cntxt_id,
+ T4_BAR2_QTYPE_INGRESS,
+ &iq->bar2_qid);
iq->size--; /* subtract status entry */
iq->netdev = dev;
iq->handler = hnd;
fl->alloc_failed = fl->large_alloc_failed = fl->starving = 0;
adap->sge.egr_map[fl->cntxt_id - adap->sge.egr_start] = fl;
- /* Note, we must initialize the Free List User Doorbell
- * address before refilling the Free List!
+ /* Note, we must initialize the BAR2 Free List User Doorbell
+ * information before refilling the Free List!
*/
- if (!is_t4(adap->params.chip))
- fl->udb = udb_address_eq(adap, fl->cntxt_id);
+ fl->bar2_addr = bar2_address(adap,
+ fl->cntxt_id,
+ T4_BAR2_QTYPE_EGRESS,
+ &fl->bar2_qid);
refill_fl(adap, fl, fl_cap(fl), GFP_KERNEL);
}
return 0;
static void init_txq(struct adapter *adap, struct sge_txq *q, unsigned int id)
{
q->cntxt_id = id;
- if (!is_t4(adap->params.chip))
- q->udb = udb_address_eq(adap, q->cntxt_id);
-
+ q->bar2_addr = bar2_address(adap,
+ q->cntxt_id,
+ T4_BAR2_QTYPE_EGRESS,
+ &q->bar2_qid);
q->in_use = 0;
q->cidx = q->pidx = 0;
q->stops = q->restarts = 0;
struct rx_sw_desc *sdesc; /* address of SW RX descriptor ring */
__be64 *desc; /* address of HW RX descriptor ring */
dma_addr_t addr; /* PCI bus address of hardware ring */
+ void __iomem *bar2_addr; /* address of BAR2 Queue registers */
+ unsigned int bar2_qid; /* Queue ID for BAR2 Queue registers */
};
/*
u16 abs_id; /* SGE abs QID for the response Q */
__be64 *desc; /* address of hardware response ring */
dma_addr_t phys_addr; /* PCI bus address of ring */
+ void __iomem *bar2_addr; /* address of BAR2 Queue registers */
+ unsigned int bar2_qid; /* Queue ID for BAR2 Queue registers */
unsigned int iqe_len; /* entry size */
unsigned int size; /* capcity of response Q */
struct adapter *adapter; /* our adapter */
struct tx_sw_desc *sdesc; /* address of SW TX descriptor ring */
struct sge_qstat *stat; /* queue status entry */
dma_addr_t phys_addr; /* PCI bus address of hardware ring */
+ void __iomem *bar2_addr; /* address of BAR2 Queue registers */
+ unsigned int bar2_qid; /* Queue ID for BAR2 Queue registers */
};
/*
struct adapter {
/* PCI resources */
void __iomem *regs;
+ void __iomem *bar2;
struct pci_dev *pdev;
struct device *pdev_dev;
unsigned int ethqsets;
int err;
u32 param, val = 0;
- unsigned int chipid;
/*
* Wait for the device to become ready before proceeding ...
return err;
}
- adapter->params.chip = 0;
- switch (adapter->pdev->device >> 12) {
- case CHELSIO_T4:
- adapter->params.chip = CHELSIO_CHIP_CODE(CHELSIO_T4, 0);
- break;
- case CHELSIO_T5:
- chipid = G_REV(t4_read_reg(adapter, A_PL_VF_REV));
- adapter->params.chip |= CHELSIO_CHIP_CODE(CHELSIO_T5, chipid);
- break;
- }
-
/*
* Grab basic operational parameters. These will predominantly have
* been set up by the Physical Function Driver or will be hard coded
{
u32 val;
- /*
- * The SGE keeps track of its Producer and Consumer Indices in terms
+ /* The SGE keeps track of its Producer and Consumer Indices in terms
* of Egress Queue Units so we can only tell it about integral numbers
* of multiples of Free List Entries per Egress Queue Units ...
*/
if (fl->pend_cred >= FL_PER_EQ_UNIT) {
- val = PIDX(fl->pend_cred / FL_PER_EQ_UNIT);
- if (!is_t4(adapter->params.chip))
- val |= DBTYPE(1);
+ if (is_t4(adapter->params.chip))
+ val = PIDX(fl->pend_cred / FL_PER_EQ_UNIT);
+ else
+ val = PIDX_T5(fl->pend_cred / FL_PER_EQ_UNIT) |
+ DBTYPE(1);
+ val |= DBPRIO(1);
+
+ /* Make sure all memory writes to the Free List queue are
+ * committed before we tell the hardware about them.
+ */
wmb();
- t4_write_reg(adapter, T4VF_SGE_BASE_ADDR + SGE_VF_KDOORBELL,
- DBPRIO(1) |
- QID(fl->cntxt_id) | val);
+
+ /* If we don't have access to the new User Doorbell (T5+), use
+ * the old doorbell mechanism; otherwise use the new BAR2
+ * mechanism.
+ */
+ if (unlikely(fl->bar2_addr == NULL)) {
+ t4_write_reg(adapter,
+ T4VF_SGE_BASE_ADDR + SGE_VF_KDOORBELL,
+ QID(fl->cntxt_id) | val);
+ } else {
+ writel(val | QID(fl->bar2_qid),
+ fl->bar2_addr + SGE_UDB_KDOORBELL);
+
+ /* This Write memory Barrier will force the write to
+ * the User Doorbell area to be flushed.
+ */
+ wmb();
+ }
fl->pend_cred %= FL_PER_EQ_UNIT;
}
}
static inline void ring_tx_db(struct adapter *adapter, struct sge_txq *tq,
int n)
{
- /*
- * Warn if we write doorbells with the wrong priority and write
- * descriptors before telling HW.
+ /* Make sure that all writes to the TX Descriptors are committed
+ * before we tell the hardware about them.
*/
- WARN_ON((QID(tq->cntxt_id) | PIDX(n)) & DBPRIO(1));
wmb();
- t4_write_reg(adapter, T4VF_SGE_BASE_ADDR + SGE_VF_KDOORBELL,
- QID(tq->cntxt_id) | PIDX(n));
+
+ /* If we don't have access to the new User Doorbell (T5+), use the old
+ * doorbell mechanism; otherwise use the new BAR2 mechanism.
+ */
+ if (unlikely(tq->bar2_addr == NULL)) {
+ u32 val = PIDX(n);
+
+ t4_write_reg(adapter, T4VF_SGE_BASE_ADDR + SGE_VF_KDOORBELL,
+ QID(tq->cntxt_id) | val);
+ } else {
+ u32 val = PIDX_T5(n);
+
+ /* T4 and later chips share the same PIDX field offset within
+ * the doorbell, but T5 and later shrank the field in order to
+ * gain a bit for Doorbell Priority. The field was absurdly
+ * large in the first place (14 bits) so we just use the T5
+ * and later limits and warn if a Queue ID is too large.
+ */
+ WARN_ON(val & DBPRIO(1));
+
+ /* If we're only writing a single Egress Unit and the BAR2
+ * Queue ID is 0, we can use the Write Combining Doorbell
+ * Gather Buffer; otherwise we use the simple doorbell.
+ */
+ if (n == 1 && tq->bar2_qid == 0) {
+ unsigned int index = (tq->pidx
+ ? (tq->pidx - 1)
+ : (tq->size - 1));
+ __be64 *src = (__be64 *)&tq->desc[index];
+ __be64 __iomem *dst = (__be64 *)(tq->bar2_addr +
+ SGE_UDB_WCDOORBELL);
+ unsigned int count = EQ_UNIT / sizeof(__be64);
+
+ /* Copy the TX Descriptor in a tight loop in order to
+ * try to get it to the adapter in a single Write
+ * Combined transfer on the PCI-E Bus. If the Write
+ * Combine fails (say because of an interrupt, etc.)
+ * the hardware will simply take the last write as a
+ * simple doorbell write with a PIDX Increment of 1
+ * and will fetch the TX Descriptor from memory via
+ * DMA.
+ */
+ while (count) {
+ writeq(*src, dst);
+ src++;
+ dst++;
+ count--;
+ }
+ } else
+ writel(val | QID(tq->bar2_qid),
+ tq->bar2_addr + SGE_UDB_KDOORBELL);
+
+ /* This Write Memory Barrier will force the write to the User
+ * Doorbell area to be flushed. This is needed to prevent
+ * writes on different CPUs for the same queue from hitting
+ * the adapter out of order. This is required when some Work
+ * Requests take the Write Combine Gather Buffer path (user
+ * doorbell area offset [SGE_UDB_WCDOORBELL..+63]) and some
+ * take the traditional path where we simply increment the
+ * PIDX (User Doorbell area SGE_UDB_KDOORBELL) and have the
+ * hardware DMA read the actual Work Request.
+ */
+ wmb();
+ }
}
/**
unsigned int intr_params;
struct sge_rspq *rspq = container_of(napi, struct sge_rspq, napi);
int work_done = process_responses(rspq, budget);
+ u32 val;
if (likely(work_done < budget)) {
napi_complete(napi);
if (unlikely(work_done == 0))
rspq->unhandled_irqs++;
- t4_write_reg(rspq->adapter,
- T4VF_SGE_BASE_ADDR + SGE_VF_GTS,
- CIDXINC(work_done) |
- INGRESSQID((u32)rspq->cntxt_id) |
- SEINTARM(intr_params));
+ val = CIDXINC(work_done) | SEINTARM(intr_params);
+ if (is_t4(rspq->adapter->params.chip)) {
+ t4_write_reg(rspq->adapter,
+ T4VF_SGE_BASE_ADDR + SGE_VF_GTS,
+ val | INGRESSQID((u32)rspq->cntxt_id));
+ } else {
+ writel(val | INGRESSQID(rspq->bar2_qid),
+ rspq->bar2_addr + SGE_UDB_GTS);
+ wmb();
+ }
return work_done;
}
struct sge *s = &adapter->sge;
struct sge_rspq *intrq = &s->intrq;
unsigned int work_done;
+ u32 val;
spin_lock(&adapter->sge.intrq_lock);
for (work_done = 0; ; work_done++) {
rspq_next(intrq);
}
- t4_write_reg(adapter, T4VF_SGE_BASE_ADDR + SGE_VF_GTS,
- CIDXINC(work_done) |
- INGRESSQID(intrq->cntxt_id) |
- SEINTARM(intrq->intr_params));
+ val = CIDXINC(work_done) | SEINTARM(intrq->intr_params);
+ if (is_t4(adapter->params.chip))
+ t4_write_reg(adapter, T4VF_SGE_BASE_ADDR + SGE_VF_GTS,
+ val | INGRESSQID(intrq->cntxt_id));
+ else {
+ writel(val | INGRESSQID(intrq->bar2_qid),
+ intrq->bar2_addr + SGE_UDB_GTS);
+ wmb();
+ }
spin_unlock(&adapter->sge.intrq_lock);
}
/**
+ * bar2_address - return the BAR2 address for an SGE Queue's Registers
+ * @adapter: the adapter
+ * @qid: the SGE Queue ID
+ * @qtype: the SGE Queue Type (Egress or Ingress)
+ * @pbar2_qid: BAR2 Queue ID or 0 for Queue ID inferred SGE Queues
+ *
+ * Returns the BAR2 address for the SGE Queue Registers associated with
+ * @qid. If BAR2 SGE Registers aren't available, returns NULL. Also
+ * returns the BAR2 Queue ID to be used with writes to the BAR2 SGE
+ * Queue Registers. If the BAR2 Queue ID is 0, then "Inferred Queue ID"
+ * Registers are supported (e.g. the Write Combining Doorbell Buffer).
+ */
+static void __iomem *bar2_address(struct adapter *adapter,
+ unsigned int qid,
+ enum t4_bar2_qtype qtype,
+ unsigned int *pbar2_qid)
+{
+ u64 bar2_qoffset;
+ int ret;
+
+ ret = t4_bar2_sge_qregs(adapter, qid, qtype,
+ &bar2_qoffset, pbar2_qid);
+ if (ret)
+ return NULL;
+
+ return adapter->bar2 + bar2_qoffset;
+}
+
+/**
* t4vf_sge_alloc_rxq - allocate an SGE RX Queue
* @adapter: the adapter
* @rspq: pointer to to the new rxq's Response Queue to be filled in
rspq->gen = 1;
rspq->next_intr_params = rspq->intr_params;
rspq->cntxt_id = be16_to_cpu(rpl.iqid);
+ rspq->bar2_addr = bar2_address(adapter,
+ rspq->cntxt_id,
+ T4_BAR2_QTYPE_INGRESS,
+ &rspq->bar2_qid);
rspq->abs_id = be16_to_cpu(rpl.physiqid);
rspq->size--; /* subtract status entry */
rspq->adapter = adapter;
fl->alloc_failed = 0;
fl->large_alloc_failed = 0;
fl->starving = 0;
+
+ /* Note, we must initialize the BAR2 Free List User Doorbell
+ * information before refilling the Free List!
+ */
+ fl->bar2_addr = bar2_address(adapter,
+ fl->cntxt_id,
+ T4_BAR2_QTYPE_EGRESS,
+ &fl->bar2_qid);
+
refill_fl(adapter, fl, fl_cap(fl), GFP_KERNEL);
}
txq->q.pidx = 0;
txq->q.stat = (void *)&txq->q.desc[txq->q.size];
txq->q.cntxt_id = FW_EQ_ETH_CMD_EQID_G(be32_to_cpu(rpl.eqid_pkd));
+ txq->q.bar2_addr = bar2_address(adapter,
+ txq->q.cntxt_id,
+ T4_BAR2_QTYPE_EGRESS,
+ &txq->q.bar2_qid);
txq->q.abs_id =
FW_EQ_ETH_CMD_PHYSEQID_G(be32_to_cpu(rpl.physeqid_pkd));
txq->txq = devq;
projects / platform / kernel / linux-rpi3.git / commitdiff