#ifndef __LINUX_USB_OTG_H
#define __LINUX_USB_OTG_H
-#include <linux/notifier.h>
+#include <linux/usb/phy.h>
/* OTG defines lots of enumeration states before device reset */
enum usb_otg_state {
OTG_STATE_A_VBUS_ERR,
};
-enum usb_phy_events {
- USB_EVENT_NONE, /* no events or cable disconnected */
- USB_EVENT_VBUS, /* vbus valid event */
- USB_EVENT_ID, /* id was grounded */
- USB_EVENT_CHARGER, /* usb dedicated charger */
- USB_EVENT_ENUMERATED, /* gadget driver enumerated */
-};
-
-/* associate a type with PHY */
-enum usb_phy_type {
- USB_PHY_TYPE_UNDEFINED,
- USB_PHY_TYPE_USB2,
- USB_PHY_TYPE_USB3,
-};
-
-struct usb_phy;
-
-/* for transceivers connected thru an ULPI interface, the user must
- * provide access ops
- */
-struct usb_phy_io_ops {
- int (*read)(struct usb_phy *x, u32 reg);
- int (*write)(struct usb_phy *x, u32 val, u32 reg);
-};
-
struct usb_otg {
u8 default_a;
};
-/*
- * the otg driver needs to interact with both device side and host side
- * usb controllers. it decides which controller is active at a given
- * moment, using the transceiver, ID signal, HNP and sometimes static
- * configuration information (including "board isn't wired for otg").
- */
-struct usb_phy {
- struct device *dev;
- const char *label;
- unsigned int flags;
-
- enum usb_phy_type type;
- enum usb_otg_state state;
- enum usb_phy_events last_event;
-
- struct usb_otg *otg;
-
- struct device *io_dev;
- struct usb_phy_io_ops *io_ops;
- void __iomem *io_priv;
-
- /* for notification of usb_phy_events */
- struct atomic_notifier_head notifier;
-
- /* to pass extra port status to the root hub */
- u16 port_status;
- u16 port_change;
-
- /* to support controllers that have multiple transceivers */
- struct list_head head;
-
- /* initialize/shutdown the OTG controller */
- int (*init)(struct usb_phy *x);
- void (*shutdown)(struct usb_phy *x);
-
- /* effective for B devices, ignored for A-peripheral */
- int (*set_power)(struct usb_phy *x,
- unsigned mA);
-
- /* for non-OTG B devices: set transceiver into suspend mode */
- int (*set_suspend)(struct usb_phy *x,
- int suspend);
-
- /* notify phy connect status change */
- int (*notify_connect)(struct usb_phy *x, int port);
- int (*notify_disconnect)(struct usb_phy *x, int port);
-};
-
-
-/* for board-specific init logic */
-extern int usb_add_phy(struct usb_phy *, enum usb_phy_type type);
-extern void usb_remove_phy(struct usb_phy *);
-
-/* helpers for direct access thru low-level io interface */
-static inline int usb_phy_io_read(struct usb_phy *x, u32 reg)
-{
- if (x->io_ops && x->io_ops->read)
- return x->io_ops->read(x, reg);
-
- return -EINVAL;
-}
-
-static inline int usb_phy_io_write(struct usb_phy *x, u32 val, u32 reg)
-{
- if (x->io_ops && x->io_ops->write)
- return x->io_ops->write(x, val, reg);
-
- return -EINVAL;
-}
-
-static inline int
-usb_phy_init(struct usb_phy *x)
-{
- if (x->init)
- return x->init(x);
-
- return 0;
-}
-
-static inline void
-usb_phy_shutdown(struct usb_phy *x)
-{
- if (x->shutdown)
- x->shutdown(x);
-}
-
-/* for usb host and peripheral controller drivers */
#ifdef CONFIG_USB_OTG_UTILS
-extern struct usb_phy *usb_get_phy(enum usb_phy_type type);
-extern struct usb_phy *devm_usb_get_phy(struct device *dev,
- enum usb_phy_type type);
-extern void usb_put_phy(struct usb_phy *);
-extern void devm_usb_put_phy(struct device *dev, struct usb_phy *x);
extern const char *otg_state_string(enum usb_otg_state state);
#else
-static inline struct usb_phy *usb_get_phy(enum usb_phy_type type)
-{
- return NULL;
-}
-
-static inline struct usb_phy *devm_usb_get_phy(struct device *dev,
- enum usb_phy_type type)
-{
- return NULL;
-}
-
-static inline void usb_put_phy(struct usb_phy *x)
-{
-}
-
-static inline void devm_usb_put_phy(struct device *dev, struct usb_phy *x)
-{
-}
-
static inline const char *otg_state_string(enum usb_otg_state state)
{
return NULL;
}
static inline int
-usb_phy_set_power(struct usb_phy *x, unsigned mA)
-{
- if (x && x->set_power)
- return x->set_power(x, mA);
- return 0;
-}
-
-/* Context: can sleep */
-static inline int
-usb_phy_set_suspend(struct usb_phy *x, int suspend)
-{
- if (x->set_suspend != NULL)
- return x->set_suspend(x, suspend);
- else
- return 0;
-}
-
-static inline int
-usb_phy_notify_connect(struct usb_phy *x, int port)
-{
- if (x->notify_connect)
- return x->notify_connect(x, port);
- else
- return 0;
-}
-
-static inline int
-usb_phy_notify_disconnect(struct usb_phy *x, int port)
-{
- if (x->notify_disconnect)
- return x->notify_disconnect(x, port);
- else
- return 0;
-}
-
-static inline int
otg_start_srp(struct usb_otg *otg)
{
if (otg && otg->start_srp)
return -ENOTSUPP;
}
-/* notifiers */
-static inline int
-usb_register_notifier(struct usb_phy *x, struct notifier_block *nb)
-{
- return atomic_notifier_chain_register(&x->notifier, nb);
-}
-
-static inline void
-usb_unregister_notifier(struct usb_phy *x, struct notifier_block *nb)
-{
- atomic_notifier_chain_unregister(&x->notifier, nb);
-}
-
/* for OTG controller drivers (and maybe other stuff) */
extern int usb_bus_start_enum(struct usb_bus *bus, unsigned port_num);
-static inline const char *usb_phy_type_string(enum usb_phy_type type)
-{
- switch (type) {
- case USB_PHY_TYPE_USB2:
- return "USB2 PHY";
- case USB_PHY_TYPE_USB3:
- return "USB3 PHY";
- default:
- return "UNKNOWN PHY TYPE";
- }
-}
#endif /* __LINUX_USB_OTG_H */
--- /dev/null
+/* USB OTG (On The Go) defines */
+/*
+ *
+ * These APIs may be used between USB controllers. USB device drivers
+ * (for either host or peripheral roles) don't use these calls; they
+ * continue to use just usb_device and usb_gadget.
+ */
+
+#ifndef __LINUX_USB_PHY_H
+#define __LINUX_USB_PHY_H
+
+#include <linux/notifier.h>
+
+enum usb_phy_events {
+ USB_EVENT_NONE, /* no events or cable disconnected */
+ USB_EVENT_VBUS, /* vbus valid event */
+ USB_EVENT_ID, /* id was grounded */
+ USB_EVENT_CHARGER, /* usb dedicated charger */
+ USB_EVENT_ENUMERATED, /* gadget driver enumerated */
+};
+
+/* associate a type with PHY */
+enum usb_phy_type {
+ USB_PHY_TYPE_UNDEFINED,
+ USB_PHY_TYPE_USB2,
+ USB_PHY_TYPE_USB3,
+};
+
+struct usb_phy;
+struct usb_otg;
+
+/* for transceivers connected thru an ULPI interface, the user must
+ * provide access ops
+ */
+struct usb_phy_io_ops {
+ int (*read)(struct usb_phy *x, u32 reg);
+ int (*write)(struct usb_phy *x, u32 val, u32 reg);
+};
+
+struct usb_phy {
+ struct device *dev;
+ const char *label;
+ unsigned int flags;
+
+ enum usb_phy_type type;
+ enum usb_phy_events last_event;
+
+ struct usb_otg *otg;
+
+ struct device *io_dev;
+ struct usb_phy_io_ops *io_ops;
+ void __iomem *io_priv;
+
+ /* for notification of usb_phy_events */
+ struct atomic_notifier_head notifier;
+
+ /* to pass extra port status to the root hub */
+ u16 port_status;
+ u16 port_change;
+
+ /* to support controllers that have multiple transceivers */
+ struct list_head head;
+
+ /* initialize/shutdown the OTG controller */
+ int (*init)(struct usb_phy *x);
+ void (*shutdown)(struct usb_phy *x);
+
+ /* effective for B devices, ignored for A-peripheral */
+ int (*set_power)(struct usb_phy *x,
+ unsigned mA);
+
+ /* for non-OTG B devices: set transceiver into suspend mode */
+ int (*set_suspend)(struct usb_phy *x,
+ int suspend);
+
+ /* notify phy connect status change */
+ int (*notify_connect)(struct usb_phy *x, int port);
+ int (*notify_disconnect)(struct usb_phy *x, int port);
+};
+
+
+/* for board-specific init logic */
+extern int usb_add_phy(struct usb_phy *, enum usb_phy_type type);
+extern void usb_remove_phy(struct usb_phy *);
+
+/* helpers for direct access thru low-level io interface */
+static inline int usb_phy_io_read(struct usb_phy *x, u32 reg)
+{
+ if (x->io_ops && x->io_ops->read)
+ return x->io_ops->read(x, reg);
+
+ return -EINVAL;
+}
+
+static inline int usb_phy_io_write(struct usb_phy *x, u32 val, u32 reg)
+{
+ if (x->io_ops && x->io_ops->write)
+ return x->io_ops->write(x, val, reg);
+
+ return -EINVAL;
+}
+
+static inline int
+usb_phy_init(struct usb_phy *x)
+{
+ if (x->init)
+ return x->init(x);
+
+ return 0;
+}
+
+static inline void
+usb_phy_shutdown(struct usb_phy *x)
+{
+ if (x->shutdown)
+ x->shutdown(x);
+}
+
+/* for usb host and peripheral controller drivers */
+#ifdef CONFIG_USB_OTG_UTILS
+extern struct usb_phy *usb_get_phy(enum usb_phy_type type);
+extern struct usb_phy *devm_usb_get_phy(struct device *dev,
+ enum usb_phy_type type);
+extern void usb_put_phy(struct usb_phy *);
+extern void devm_usb_put_phy(struct device *dev, struct usb_phy *x);
+#else
+static inline struct usb_phy *usb_get_phy(enum usb_phy_type type)
+{
+ return NULL;
+}
+
+static inline struct usb_phy *devm_usb_get_phy(struct device *dev,
+ enum usb_phy_type type)
+{
+ return NULL;
+}
+
+static inline void usb_put_phy(struct usb_phy *x)
+{
+}
+
+static inline void devm_usb_put_phy(struct device *dev, struct usb_phy *x)
+{
+}
+
+#endif
+
+static inline int
+usb_phy_set_power(struct usb_phy *x, unsigned mA)
+{
+ if (x && x->set_power)
+ return x->set_power(x, mA);
+ return 0;
+}
+
+/* Context: can sleep */
+static inline int
+usb_phy_set_suspend(struct usb_phy *x, int suspend)
+{
+ if (x->set_suspend != NULL)
+ return x->set_suspend(x, suspend);
+ else
+ return 0;
+}
+
+static inline int
+usb_phy_notify_connect(struct usb_phy *x, int port)
+{
+ if (x->notify_connect)
+ return x->notify_connect(x, port);
+ else
+ return 0;
+}
+
+static inline int
+usb_phy_notify_disconnect(struct usb_phy *x, int port)
+{
+ if (x->notify_disconnect)
+ return x->notify_disconnect(x, port);
+ else
+ return 0;
+}
+
+/* notifiers */
+static inline int
+usb_register_notifier(struct usb_phy *x, struct notifier_block *nb)
+{
+ return atomic_notifier_chain_register(&x->notifier, nb);
+}
+
+static inline void
+usb_unregister_notifier(struct usb_phy *x, struct notifier_block *nb)
+{
+ atomic_notifier_chain_unregister(&x->notifier, nb);
+}
+
+static inline const char *usb_phy_type_string(enum usb_phy_type type)
+{
+ switch (type) {
+ case USB_PHY_TYPE_USB2:
+ return "USB2 PHY";
+ case USB_PHY_TYPE_USB3:
+ return "USB3 PHY";
+ default:
+ return "UNKNOWN PHY TYPE";
+ }
+}
+#endif /* __LINUX_USB_PHY_H */
projects / platform / adaptation / renesas_rcar / renesas_kernel.git / commitdiff