#define ETS_E3B0_PBF_MIN_W_VAL (10000)
#define MAX_PACKET_SIZE (9700)
-#define WC_UC_TIMEOUT 100
#define MAX_KR_LINK_RETRY 4
/**********************************************************/
/* Reset UMAC */
REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_2_CLEAR,
(MISC_REGISTERS_RESET_REG_2_UMAC0 << params->port));
- usleep_range(1000, 1000);
+ usleep_range(1000, 2000);
REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_2_SET,
(MISC_REGISTERS_RESET_REG_2_UMAC0 << params->port));
/* Hard reset */
REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_2_CLEAR,
MISC_REGISTERS_RESET_REG_2_XMAC);
- usleep_range(1000, 1000);
+ usleep_range(1000, 2000);
REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_2_SET,
MISC_REGISTERS_RESET_REG_2_XMAC);
/* Soft reset */
REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_2_CLEAR,
MISC_REGISTERS_RESET_REG_2_XMAC_SOFT);
- usleep_range(1000, 1000);
+ usleep_range(1000, 2000);
REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_2_SET,
MISC_REGISTERS_RESET_REG_2_XMAC_SOFT);
bnx2x_bits_en(bp, emac_base + EMAC_REG_EMAC_TX_MODE,
EMAC_TX_MODE_RESET);
- if (CHIP_REV_IS_SLOW(bp)) {
- /* config GMII mode */
- val = REG_RD(bp, emac_base + EMAC_REG_EMAC_MODE);
- EMAC_WR(bp, EMAC_REG_EMAC_MODE, (val | EMAC_MODE_PORT_GMII));
- } else { /* ASIC */
/* pause enable/disable */
bnx2x_bits_dis(bp, emac_base + EMAC_REG_EMAC_RX_MODE,
EMAC_RX_MODE_FLOW_EN);
} else
bnx2x_bits_en(bp, emac_base + EMAC_REG_EMAC_TX_MODE,
EMAC_TX_MODE_FLOW_EN);
- }
/* KEEP_VLAN_TAG, promiscuous */
val = REG_RD(bp, emac_base + EMAC_REG_EMAC_RX_MODE);
val &= ~0x810;
EMAC_WR(bp, EMAC_REG_EMAC_MODE, val);
- /* enable emac */
+ /* Enable emac */
REG_WR(bp, NIG_REG_NIG_EMAC0_EN + port*4, 1);
- /* enable emac for jumbo packets */
+ /* Enable emac for jumbo packets */
EMAC_WR(bp, EMAC_REG_EMAC_RX_MTU_SIZE,
(EMAC_RX_MTU_SIZE_JUMBO_ENA |
(ETH_MAX_JUMBO_PACKET_SIZE + ETH_OVREHEAD)));
- /* strip CRC */
+ /* Strip CRC */
REG_WR(bp, NIG_REG_NIG_INGRESS_EMAC0_NO_CRC + port*4, 0x1);
- /* disable the NIG in/out to the bmac */
+ /* Disable the NIG in/out to the bmac */
REG_WR(bp, NIG_REG_BMAC0_IN_EN + port*4, 0x0);
REG_WR(bp, NIG_REG_BMAC0_PAUSE_OUT_EN + port*4, 0x0);
REG_WR(bp, NIG_REG_BMAC0_OUT_EN + port*4, 0x0);
- /* enable the NIG in/out to the emac */
+ /* Enable the NIG in/out to the emac */
REG_WR(bp, NIG_REG_EMAC0_IN_EN + port*4, 0x1);
val = 0;
if ((params->feature_config_flags &
wb_data[1] = 0;
REG_WR_DMAE(bp, bmac_addr + BIGMAC_REGISTER_RX_CONTROL, wb_data, 2);
- /* tx control */
+ /* TX control */
val = 0xc0;
if (!(params->feature_config_flags &
FEATURE_CONFIG_PFC_ENABLED) &&
wb_data[0] &= ~(1<<2);
} else {
DP(NETIF_MSG_LINK, "PFC is disabled\n");
- /* disable PFC RX & TX & STATS and set 8 COS */
+ /* Disable PFC RX & TX & STATS and set 8 COS */
wb_data[0] = 0x8;
wb_data[1] = 0;
}
PFC_E2_BRB_MAC_FULL_XOFF_THR_PAUSE;
config_val->pauseable_th.full_xon =
PFC_E2_BRB_MAC_FULL_XON_THR_PAUSE;
- /* non pause able*/
+ /* Non pause able*/
config_val->non_pauseable_th.pause_xoff =
PFC_E2_BRB_MAC_PAUSE_XOFF_THR_NON_PAUSE;
config_val->non_pauseable_th.pause_xon =
PFC_E3A0_BRB_MAC_FULL_XOFF_THR_PAUSE;
config_val->pauseable_th.full_xon =
PFC_E3A0_BRB_MAC_FULL_XON_THR_PAUSE;
- /* non pause able*/
+ /* Non pause able*/
config_val->non_pauseable_th.pause_xoff =
PFC_E3A0_BRB_MAC_PAUSE_XOFF_THR_NON_PAUSE;
config_val->non_pauseable_th.pause_xon =
PFC_E3B0_4P_BRB_MAC_FULL_XOFF_THR_PAUSE;
config_val->pauseable_th.full_xon =
PFC_E3B0_4P_BRB_MAC_FULL_XON_THR_PAUSE;
- /* non pause able*/
+ /* Non pause able*/
config_val->non_pauseable_th.pause_xoff =
PFC_E3B0_4P_BRB_MAC_PAUSE_XOFF_THR_NON_PAUSE;
config_val->non_pauseable_th.pause_xon =
PFC_E3B0_2P_BRB_MAC_FULL_XOFF_THR_PAUSE;
config_val->pauseable_th.full_xon =
PFC_E3B0_2P_BRB_MAC_FULL_XON_THR_PAUSE;
- /* non pause able*/
+ /* Non pause able*/
config_val->non_pauseable_th.pause_xoff =
PFC_E3B0_2P_BRB_MAC_PAUSE_XOFF_THR_NON_PAUSE;
config_val->non_pauseable_th.pause_xon =
if (pfc_params->cos0_pauseable !=
pfc_params->cos1_pauseable) {
- /* nonpauseable= Lossy + pauseable = Lossless*/
+ /* Nonpauseable= Lossy + pauseable = Lossless*/
e3b0_val->lb_guarantied =
PFC_E3B0_2P_MIX_PAUSE_LB_GUART;
e3b0_val->mac_0_class_t_guarantied =
* This function is needed because NIG ARB_CREDIT_WEIGHT_X are
* not continues and ARB_CREDIT_WEIGHT_0 + offset is suitable.
******************************************************************************/
-int bnx2x_pfc_nig_rx_priority_mask(struct bnx2x *bp,
- u8 cos_entry,
- u32 priority_mask, u8 port)
+static int bnx2x_pfc_nig_rx_priority_mask(struct bnx2x *bp,
+ u8 cos_entry,
+ u32 priority_mask, u8 port)
{
u32 nig_reg_rx_priority_mask_add = 0;
REG_WR(bp, port ? NIG_REG_LLFC_EGRESS_SRC_ENABLE_1 :
NIG_REG_LLFC_EGRESS_SRC_ENABLE_0, 0x7);
- /* output enable for RX_XCM # IF */
+ /* Output enable for RX_XCM # IF */
REG_WR(bp, port ? NIG_REG_XCM1_OUT_EN :
NIG_REG_XCM0_OUT_EN, xcm_out_en);
bnx2x_update_mng(params, vars->link_status);
- /* update NIG params */
+ /* Update NIG params */
bnx2x_update_pfc_nig(params, vars, pfc_params);
- /* update BRB params */
+ /* Update BRB params */
bnx2x_status = bnx2x_update_pfc_brb(params, vars, pfc_params);
if (bnx2x_status)
return bnx2x_status;
REG_WR_DMAE(bp, bmac_addr + BIGMAC_REGISTER_BMAC_XGXS_CONTROL,
wb_data, 2);
- /* tx MAC SA */
+ /* TX MAC SA */
wb_data[0] = ((params->mac_addr[2] << 24) |
(params->mac_addr[3] << 16) |
(params->mac_addr[4] << 8) |
params->mac_addr[1]);
REG_WR_DMAE(bp, bmac_addr + BIGMAC_REGISTER_TX_SOURCE_ADDR, wb_data, 2);
- /* mac control */
+ /* MAC control */
val = 0x3;
if (is_lb) {
val |= 0x4;
wb_data[1] = 0;
REG_WR_DMAE(bp, bmac_addr + BIGMAC_REGISTER_BMAC_CONTROL, wb_data, 2);
- /* set rx mtu */
+ /* Set rx mtu */
wb_data[0] = ETH_MAX_JUMBO_PACKET_SIZE + ETH_OVREHEAD;
wb_data[1] = 0;
REG_WR_DMAE(bp, bmac_addr + BIGMAC_REGISTER_RX_MAX_SIZE, wb_data, 2);
bnx2x_update_pfc_bmac1(params, vars);
- /* set tx mtu */
+ /* Set tx mtu */
wb_data[0] = ETH_MAX_JUMBO_PACKET_SIZE + ETH_OVREHEAD;
wb_data[1] = 0;
REG_WR_DMAE(bp, bmac_addr + BIGMAC_REGISTER_TX_MAX_SIZE, wb_data, 2);
- /* set cnt max size */
+ /* Set cnt max size */
wb_data[0] = ETH_MAX_JUMBO_PACKET_SIZE + ETH_OVREHEAD;
wb_data[1] = 0;
REG_WR_DMAE(bp, bmac_addr + BIGMAC_REGISTER_CNT_MAX_SIZE, wb_data, 2);
- /* configure safc */
+ /* Configure SAFC */
wb_data[0] = 0x1000200;
wb_data[1] = 0;
REG_WR_DMAE(bp, bmac_addr + BIGMAC_REGISTER_RX_LLFC_MSG_FLDS,
udelay(30);
- /* tx MAC SA */
+ /* TX MAC SA */
wb_data[0] = ((params->mac_addr[2] << 24) |
(params->mac_addr[3] << 16) |
(params->mac_addr[4] << 8) |
wb_data, 2);
udelay(30);
- /* set rx mtu */
+ /* Set RX MTU */
wb_data[0] = ETH_MAX_JUMBO_PACKET_SIZE + ETH_OVREHEAD;
wb_data[1] = 0;
REG_WR_DMAE(bp, bmac_addr + BIGMAC2_REGISTER_RX_MAX_SIZE, wb_data, 2);
udelay(30);
- /* set tx mtu */
+ /* Set TX MTU */
wb_data[0] = ETH_MAX_JUMBO_PACKET_SIZE + ETH_OVREHEAD;
wb_data[1] = 0;
REG_WR_DMAE(bp, bmac_addr + BIGMAC2_REGISTER_TX_MAX_SIZE, wb_data, 2);
udelay(30);
- /* set cnt max size */
+ /* Set cnt max size */
wb_data[0] = ETH_MAX_JUMBO_PACKET_SIZE + ETH_OVREHEAD - 2;
wb_data[1] = 0;
REG_WR_DMAE(bp, bmac_addr + BIGMAC2_REGISTER_CNT_MAX_SIZE, wb_data, 2);
u8 port = params->port;
struct bnx2x *bp = params->bp;
u32 val;
- /* reset and unreset the BigMac */
+ /* Reset and unreset the BigMac */
REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_2_CLEAR,
(MISC_REGISTERS_RESET_REG_2_RST_BMAC0 << port));
- msleep(1);
+ usleep_range(1000, 2000);
REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_2_SET,
(MISC_REGISTERS_RESET_REG_2_RST_BMAC0 << port));
- /* enable access for bmac registers */
+ /* Enable access for bmac registers */
REG_WR(bp, NIG_REG_BMAC0_REGS_OUT_EN + port*4, 0x1);
/* Enable BMAC according to BMAC type*/
BIGMAC_REGISTER_BMAC_CONTROL,
wb_data, 2);
}
- msleep(1);
+ usleep_range(1000, 2000);
}
}
u32 init_crd, crd;
u32 count = 1000;
- /* disable port */
+ /* Disable port */
REG_WR(bp, PBF_REG_DISABLE_NEW_TASK_PROC_P0 + port*4, 0x1);
- /* wait for init credit */
+ /* Wait for init credit */
init_crd = REG_RD(bp, PBF_REG_P0_INIT_CRD + port*4);
crd = REG_RD(bp, PBF_REG_P0_CREDIT + port*8);
DP(NETIF_MSG_LINK, "init_crd 0x%x crd 0x%x\n", init_crd, crd);
while ((init_crd != crd) && count) {
- msleep(5);
-
+ usleep_range(5000, 10000);
crd = REG_RD(bp, PBF_REG_P0_CREDIT + port*8);
count--;
}
line_speed == SPEED_1000 ||
line_speed == SPEED_2500) {
REG_WR(bp, PBF_REG_P0_PAUSE_ENABLE + port*4, 1);
- /* update threshold */
+ /* Update threshold */
REG_WR(bp, PBF_REG_P0_ARB_THRSH + port*4, 0);
- /* update init credit */
+ /* Update init credit */
init_crd = 778; /* (800-18-4) */
} else {
u32 thresh = (ETH_MAX_JUMBO_PACKET_SIZE +
ETH_OVREHEAD)/16;
REG_WR(bp, PBF_REG_P0_PAUSE_ENABLE + port*4, 0);
- /* update threshold */
+ /* Update threshold */
REG_WR(bp, PBF_REG_P0_ARB_THRSH + port*4, thresh);
- /* update init credit */
+ /* Update init credit */
switch (line_speed) {
case SPEED_10000:
init_crd = thresh + 553 - 22;
DP(NETIF_MSG_LINK, "PBF updated to speed %d credit %d\n",
line_speed, init_crd);
- /* probe the credit changes */
+ /* Probe the credit changes */
REG_WR(bp, PBF_REG_INIT_P0 + port*4, 0x1);
- msleep(5);
+ usleep_range(5000, 10000);
REG_WR(bp, PBF_REG_INIT_P0 + port*4, 0x0);
- /* enable port */
+ /* Enable port */
REG_WR(bp, PBF_REG_DISABLE_NEW_TASK_PROC_P0 + port*4, 0x0);
return 0;
}
REG_WR(bp, phy->mdio_ctrl + EMAC_REG_EMAC_MDIO_MODE,
mode & ~EMAC_MDIO_MODE_CLAUSE_45);
- /* address */
+ /* Address */
tmp = ((phy->addr << 21) | (reg << 16) | val |
EMAC_MDIO_COMM_COMMAND_WRITE_22 |
EMAC_MDIO_COMM_START_BUSY);
REG_WR(bp, phy->mdio_ctrl + EMAC_REG_EMAC_MDIO_MODE,
mode & ~EMAC_MDIO_MODE_CLAUSE_45);
- /* address */
+ /* Address */
val = ((phy->addr << 21) | (reg << 16) |
EMAC_MDIO_COMM_COMMAND_READ_22 |
EMAC_MDIO_COMM_START_BUSY);
if (phy->flags & FLAGS_MDC_MDIO_WA_B0)
bnx2x_bits_en(bp, phy->mdio_ctrl + EMAC_REG_EMAC_MDIO_STATUS,
EMAC_MDIO_STATUS_10MB);
- /* address */
+ /* Address */
val = ((phy->addr << 21) | (devad << 16) | reg |
EMAC_MDIO_COMM_COMMAND_ADDRESS |
EMAC_MDIO_COMM_START_BUSY);
*ret_val = 0;
rc = -EFAULT;
} else {
- /* data */
+ /* Data */
val = ((phy->addr << 21) | (devad << 16) |
EMAC_MDIO_COMM_COMMAND_READ_45 |
EMAC_MDIO_COMM_START_BUSY);
bnx2x_bits_en(bp, phy->mdio_ctrl + EMAC_REG_EMAC_MDIO_STATUS,
EMAC_MDIO_STATUS_10MB);
- /* address */
+ /* Address */
tmp = ((phy->addr << 21) | (devad << 16) | reg |
EMAC_MDIO_COMM_COMMAND_ADDRESS |
EMAC_MDIO_COMM_START_BUSY);
netdev_err(bp->dev, "MDC/MDIO access timeout\n");
rc = -EFAULT;
} else {
- /* data */
+ /* Data */
tmp = ((phy->addr << 21) | (devad << 16) | val |
EMAC_MDIO_COMM_COMMAND_WRITE_45 |
EMAC_MDIO_COMM_START_BUSY);
xfer_cnt = 16 - lc_addr;
- /* enable the engine */
+ /* Enable the engine */
val = REG_RD(bp, MCP_REG_MCPR_IMC_COMMAND);
val |= MCPR_IMC_COMMAND_ENABLE;
REG_WR(bp, MCP_REG_MCPR_IMC_COMMAND, val);
- /* program slave device ID */
+ /* Program slave device ID */
val = (sl_devid << 16) | sl_addr;
REG_WR(bp, MCP_REG_MCPR_IMC_SLAVE_CONTROL, val);
- /* start xfer with 0 byte to update the address pointer ???*/
+ /* Start xfer with 0 byte to update the address pointer ???*/
val = (MCPR_IMC_COMMAND_ENABLE) |
(MCPR_IMC_COMMAND_WRITE_OP <<
MCPR_IMC_COMMAND_OPERATION_BITSHIFT) |
(lc_addr << MCPR_IMC_COMMAND_TRANSFER_ADDRESS_BITSHIFT) | (0);
REG_WR(bp, MCP_REG_MCPR_IMC_COMMAND, val);
- /* poll for completion */
+ /* Poll for completion */
i = 0;
val = REG_RD(bp, MCP_REG_MCPR_IMC_COMMAND);
while (((val >> MCPR_IMC_COMMAND_IMC_STATUS_BITSHIFT) & 0x3) != 1) {
if (rc == -EFAULT)
return rc;
- /* start xfer with read op */
+ /* Start xfer with read op */
val = (MCPR_IMC_COMMAND_ENABLE) |
(MCPR_IMC_COMMAND_READ_OP <<
MCPR_IMC_COMMAND_OPERATION_BITSHIFT) |
(xfer_cnt);
REG_WR(bp, MCP_REG_MCPR_IMC_COMMAND, val);
- /* poll for completion */
+ /* Poll for completion */
i = 0;
val = REG_RD(bp, MCP_REG_MCPR_IMC_COMMAND);
while (((val >> MCPR_IMC_COMMAND_IMC_STATUS_BITSHIFT) & 0x3) != 1) {
port = port ^ 1;
lane = (port<<1) + path;
- } else { /* two port mode - no port swap */
+ } else { /* Two port mode - no port swap */
/* Figure out path swap value */
path_swap_ovr =
val = SERDES_RESET_BITS << (port*16);
- /* reset and unreset the SerDes/XGXS */
+ /* Reset and unreset the SerDes/XGXS */
REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_3_CLEAR, val);
udelay(500);
REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_3_SET, val);
val = XGXS_RESET_BITS << (port*16);
- /* reset and unreset the SerDes/XGXS */
+ /* Reset and unreset the SerDes/XGXS */
REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_3_CLEAR, val);
udelay(500);
REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_3_SET, val);
{
u16 val;
struct bnx2x *bp = params->bp;
- /* read modify write pause advertizing */
+ /* Read modify write pause advertizing */
bnx2x_cl45_read(bp, phy, MDIO_AN_DEVAD, MDIO_AN_REG_ADV_PAUSE, &val);
val &= ~MDIO_AN_REG_ADV_PAUSE_BOTH;
bnx2x_cl45_read_or_write(bp, phy, MDIO_WC_DEVAD,
MDIO_WC_REG_RX66_CONTROL, 0xF9);
- /* set and clear loopback to cause a reset to 64/66 decoder */
+ /* Set and clear loopback to cause a reset to 64/66 decoder */
bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
MDIO_WC_REG_IEEE0BLK_MIICNTL, 0x4000);
bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
if (!vars->turn_to_run_wc_rt)
return;
- /* return if there is no link partner */
+ /* Return if there is no link partner */
if (!(bnx2x_warpcore_get_sigdet(phy, params))) {
DP(NETIF_MSG_LINK, "bnx2x_warpcore_get_sigdet false\n");
return;
bnx2x_warpcore_reset_lane(bp, phy, 1);
bnx2x_warpcore_reset_lane(bp, phy, 0);
- /* restart Autoneg */
+ /* Restart Autoneg */
bnx2x_cl45_write(bp, phy, MDIO_AN_DEVAD,
MDIO_WC_REG_IEEE0BLK_MIICNTL, 0x1200);
}
-void bnx2x_sync_link(struct link_params *params,
- struct link_vars *vars)
+
+static void bnx2x_sync_link(struct link_params *params,
+ struct link_vars *vars)
{
struct bnx2x *bp = params->bp;
u8 link_10g_plus;
USES_WARPCORE(bp) &&
(vars->line_speed == SPEED_1000))
vars->phy_flags |= PHY_SGMII_FLAG;
- /* anything 10 and over uses the bmac */
+ /* Anything 10 and over uses the bmac */
link_10g_plus = (vars->line_speed >= SPEED_10000);
if (link_10g_plus) {
else
vars->mac_type = MAC_TYPE_EMAC;
}
- } else { /* link down */
+ } else { /* Link down */
DP(NETIF_MSG_LINK, "phy link down\n");
vars->phy_link_up = 0;
vars->duplex = DUPLEX_FULL;
vars->flow_ctrl = BNX2X_FLOW_CTRL_NONE;
- /* indicate no mac active */
+ /* Indicate no mac active */
vars->mac_type = MAC_TYPE_NONE;
if (vars->link_status & LINK_STATUS_PHYSICAL_LINK_FLAG)
vars->phy_flags |= PHY_HALF_OPEN_CONN_FLAG;
PORT_HW_CFG_LANE_SWAP_CFG_MASTER_MASK) >>
PORT_HW_CFG_LANE_SWAP_CFG_MASTER_SHIFT);
- /* set the master_ln for AN */
+ /* Set the master_ln for AN */
CL22_RD_OVER_CL45(bp, phy,
MDIO_REG_BANK_XGXS_BLOCK2,
MDIO_XGXS_BLOCK2_TEST_MODE_LANE,
MDIO_REG_BANK_COMBO_IEEE0,
MDIO_COMBO_IEEE0_MII_CONTROL, &mii_control);
- /* reset the unicore */
+ /* Reset the unicore */
CL22_WR_OVER_CL45(bp, phy,
MDIO_REG_BANK_COMBO_IEEE0,
MDIO_COMBO_IEEE0_MII_CONTROL,
if (set_serdes)
bnx2x_set_serdes_access(bp, params->port);
- /* wait for the reset to self clear */
+ /* Wait for the reset to self clear */
for (i = 0; i < MDIO_ACCESS_TIMEOUT; i++) {
udelay(5);
- /* the reset erased the previous bank value */
+ /* The reset erased the previous bank value */
CL22_RD_OVER_CL45(bp, phy,
MDIO_REG_BANK_COMBO_IEEE0,
MDIO_COMBO_IEEE0_MII_CONTROL,
MDIO_CL73_IEEEB0_CL73_AN_CONTROL, reg_val);
}
-/* program SerDes, forced speed */
+/* Program SerDes, forced speed */
static void bnx2x_program_serdes(struct bnx2x_phy *phy,
struct link_params *params,
struct link_vars *vars)
struct bnx2x *bp = params->bp;
u16 reg_val;
- /* program duplex, disable autoneg and sgmii*/
+ /* Program duplex, disable autoneg and sgmii*/
CL22_RD_OVER_CL45(bp, phy,
MDIO_REG_BANK_COMBO_IEEE0,
MDIO_COMBO_IEEE0_MII_CONTROL, ®_val);
CL22_RD_OVER_CL45(bp, phy,
MDIO_REG_BANK_SERDES_DIGITAL,
MDIO_SERDES_DIGITAL_MISC1, ®_val);
- /* clearing the speed value before setting the right speed */
+ /* Clearing the speed value before setting the right speed */
DP(NETIF_MSG_LINK, "MDIO_REG_BANK_SERDES_DIGITAL = 0x%x\n", reg_val);
reg_val &= ~(MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_MASK |
struct bnx2x *bp = params->bp;
u16 val = 0;
- /* set extended capabilities */
+ /* Set extended capabilities */
if (phy->speed_cap_mask & PORT_HW_CFG_SPEED_CAPABILITY_D0_2_5G)
val |= MDIO_OVER_1G_UP1_2_5G;
if (phy->speed_cap_mask & PORT_HW_CFG_SPEED_CAPABILITY_D0_10G)
{
struct bnx2x *bp = params->bp;
u16 val;
- /* for AN, we are always publishing full duplex */
+ /* For AN, we are always publishing full duplex */
CL22_WR_OVER_CL45(bp, phy,
MDIO_REG_BANK_COMBO_IEEE0,
struct bnx2x *bp = params->bp;
u16 control1;
- /* in SGMII mode, the unicore is always slave */
+ /* In SGMII mode, the unicore is always slave */
CL22_RD_OVER_CL45(bp, phy,
MDIO_REG_BANK_SERDES_DIGITAL,
MDIO_SERDES_DIGITAL_A_1000X_CONTROL1,
&control1);
control1 |= MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_INVERT_SIGNAL_DETECT;
- /* set sgmii mode (and not fiber) */
+ /* Set sgmii mode (and not fiber) */
control1 &= ~(MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_FIBER_MODE |
MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_AUTODET |
MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_MSTR_MODE);
MDIO_SERDES_DIGITAL_A_1000X_CONTROL1,
control1);
- /* if forced speed */
+ /* If forced speed */
if (!(vars->line_speed == SPEED_AUTO_NEG)) {
- /* set speed, disable autoneg */
+ /* Set speed, disable autoneg */
u16 mii_control;
CL22_RD_OVER_CL45(bp, phy,
MDIO_COMBO_IEEO_MII_CONTROL_MAN_SGMII_SP_1000;
break;
case SPEED_10:
- /* there is nothing to set for 10M */
+ /* There is nothing to set for 10M */
break;
default:
- /* invalid speed for SGMII */
+ /* Invalid speed for SGMII */
DP(NETIF_MSG_LINK, "Invalid line_speed 0x%x\n",
vars->line_speed);
break;
}
- /* setting the full duplex */
+ /* Setting the full duplex */
if (phy->req_duplex == DUPLEX_FULL)
mii_control |=
MDIO_COMBO_IEEO_MII_CONTROL_FULL_DUPLEX;
mii_control);
} else { /* AN mode */
- /* enable and restart AN */
+ /* Enable and restart AN */
bnx2x_restart_autoneg(phy, params, 0);
}
}
struct bnx2x *bp = params->bp;
vars->flow_ctrl = BNX2X_FLOW_CTRL_NONE;
- /* resolve from gp_status in case of AN complete and not sgmii */
+ /* Resolve from gp_status in case of AN complete and not sgmii */
if (phy->req_flow_ctrl != BNX2X_FLOW_CTRL_AUTO) {
/* Update the advertised flow-controled of LD/LP in AN */
if (phy->req_line_speed == SPEED_AUTO_NEG)
bnx2x_xgxs_an_resolve(phy, params, vars,
gp_status);
}
- } else { /* link_down */
+ } else { /* Link_down */
if ((phy->req_line_speed == SPEED_AUTO_NEG) &&
SINGLE_MEDIA_DIRECT(params)) {
/* Check signal is detected */
u16 tx_driver;
u16 bank;
- /* read precomp */
+ /* Read precomp */
CL22_RD_OVER_CL45(bp, phy,
MDIO_REG_BANK_OVER_1G,
MDIO_OVER_1G_LP_UP2, &lp_up2);
- /* bits [10:7] at lp_up2, positioned at [15:12] */
+ /* Bits [10:7] at lp_up2, positioned at [15:12] */
lp_up2 = (((lp_up2 & MDIO_OVER_1G_LP_UP2_PREEMPHASIS_MASK) >>
MDIO_OVER_1G_LP_UP2_PREEMPHASIS_SHIFT) <<
MDIO_TX0_TX_DRIVER_PREEMPHASIS_SHIFT);
bank,
MDIO_TX0_TX_DRIVER, &tx_driver);
- /* replace tx_driver bits [15:12] */
+ /* Replace tx_driver bits [15:12] */
if (lp_up2 !=
(tx_driver & MDIO_TX0_TX_DRIVER_PREEMPHASIS_MASK)) {
tx_driver &= ~MDIO_TX0_TX_DRIVER_PREEMPHASIS_MASK;
FEATURE_CONFIG_OVERRIDE_PREEMPHASIS_ENABLED))
bnx2x_set_preemphasis(phy, params);
- /* forced speed requested? */
+ /* Forced speed requested? */
if (vars->line_speed != SPEED_AUTO_NEG ||
(SINGLE_MEDIA_DIRECT(params) &&
params->loopback_mode == LOOPBACK_EXT)) {
DP(NETIF_MSG_LINK, "not SGMII, no AN\n");
- /* disable autoneg */
+ /* Disable autoneg */
bnx2x_set_autoneg(phy, params, vars, 0);
- /* program speed and duplex */
+ /* Program speed and duplex */
bnx2x_program_serdes(phy, params, vars);
} else { /* AN_mode */
/* AN enabled */
bnx2x_set_brcm_cl37_advertisement(phy, params);
- /* program duplex & pause advertisement (for aneg) */
+ /* Program duplex & pause advertisement (for aneg) */
bnx2x_set_ieee_aneg_advertisement(phy, params,
vars->ieee_fc);
- /* enable autoneg */
+ /* Enable autoneg */
bnx2x_set_autoneg(phy, params, vars, enable_cl73);
- /* enable and restart AN */
+ /* Enable and restart AN */
bnx2x_restart_autoneg(phy, params, enable_cl73);
}
bnx2x_set_master_ln(params, phy);
rc = bnx2x_reset_unicore(params, phy, 0);
- /* reset the SerDes and wait for reset bit return low */
- if (rc != 0)
+ /* Reset the SerDes and wait for reset bit return low */
+ if (rc)
return rc;
bnx2x_set_aer_mmd(params, phy);
- /* setting the masterLn_def again after the reset */
+ /* Setting the masterLn_def again after the reset */
if (phy->type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_DIRECT) {
bnx2x_set_master_ln(params, phy);
bnx2x_set_swap_lanes(params, phy);
MDIO_PMA_REG_CTRL, &ctrl);
if (!(ctrl & (1<<15)))
break;
- msleep(1);
+ usleep_range(1000, 2000);
}
if (cnt == 1000)
DP(NETIF_MSG_LINK, "XGXS 10G loopback enable\n");
if (!CHIP_IS_E3(bp)) {
- /* change the uni_phy_addr in the nig */
+ /* Change the uni_phy_addr in the nig */
md_devad = REG_RD(bp, (NIG_REG_XGXS0_CTRL_MD_DEVAD +
port*0x18));
(MDIO_CL73_IEEEB0_CL73_AN_CONTROL & 0xf)),
0x6041);
msleep(200);
- /* set aer mmd back */
+ /* Set aer mmd back */
bnx2x_set_aer_mmd(params, phy);
if (!CHIP_IS_E3(bp)) {
- /* and md_devad */
+ /* And md_devad */
REG_WR(bp, NIG_REG_XGXS0_CTRL_MD_DEVAD + port*0x18,
md_devad);
}
MDIO_REG_BANK_GP_STATUS,
MDIO_GP_STATUS_TOP_AN_STATUS1,
&gp_status);
- /* link is up only if both local phy and external phy are up */
+ /* Link is up only if both local phy and external phy are up */
if (!(gp_status & MDIO_GP_STATUS_TOP_AN_STATUS1_LINK_STATUS))
return -ESRCH;
}
static void bnx2x_int_link_reset(struct bnx2x_phy *phy,
struct link_params *params)
{
- /* reset the SerDes/XGXS */
+ /* Reset the SerDes/XGXS */
REG_WR(params->bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_3_CLEAR,
(0x1ff << (params->port*16)));
}
DP(NETIF_MSG_LINK, "Port %x: Link is down\n", port);
bnx2x_set_led(params, vars, LED_MODE_OFF, 0);
vars->phy_flags &= ~PHY_PHYSICAL_LINK_FLAG;
- /* indicate no mac active */
+ /* Indicate no mac active */
vars->mac_type = MAC_TYPE_NONE;
- /* update shared memory */
+ /* Update shared memory */
vars->link_status &= ~(LINK_STATUS_SPEED_AND_DUPLEX_MASK |
LINK_STATUS_LINK_UP |
LINK_STATUS_PHYSICAL_LINK_FLAG |
vars->line_speed = 0;
bnx2x_update_mng(params, vars->link_status);
- /* activate nig drain */
+ /* Activate nig drain */
REG_WR(bp, NIG_REG_EGRESS_DRAIN0_MODE + port*4, 1);
- /* disable emac */
+ /* Disable emac */
if (!CHIP_IS_E3(bp))
REG_WR(bp, NIG_REG_NIG_EMAC0_EN + port*4, 0);
- msleep(10);
- /* reset BigMac/Xmac */
+ usleep_range(10000, 20000);
+ /* Reset BigMac/Xmac */
if (CHIP_IS_E1x(bp) ||
CHIP_IS_E2(bp)) {
bnx2x_bmac_rx_disable(bp, params->port);
(MISC_REGISTERS_RESET_REG_2_RST_BMAC0 << port));
}
if (CHIP_IS_E3(bp)) {
+ /* Prevent LPI Generation by chip */
REG_WR(bp, MISC_REG_CPMU_LP_FW_ENABLE_P0 + (params->port << 2),
0);
REG_WR(bp, MISC_REG_CPMU_LP_DR_ENABLE, 0);
rc |= bnx2x_pbf_update(params, vars->flow_ctrl,
vars->line_speed);
- /* disable drain */
+ /* Disable drain */
REG_WR(bp, NIG_REG_EGRESS_DRAIN0_MODE + port*4, 0);
- /* update shared memory */
+ /* Update shared memory */
bnx2x_update_mng(params, vars->link_status);
bnx2x_update_mng_eee(params, vars->eee_status);
/* Check remote fault */
REG_RD(bp, NIG_REG_XGXS0_STATUS_LINK10G + port*0x68),
REG_RD(bp, NIG_REG_XGXS0_STATUS_LINK_STATUS + port*0x68));
- /* disable emac */
+ /* Disable emac */
if (!CHIP_IS_E3(bp))
REG_WR(bp, NIG_REG_NIG_EMAC0_EN + port*4, 0);
} else if (prev_line_speed != vars->line_speed) {
REG_WR(bp, NIG_REG_EGRESS_DRAIN0_MODE + params->port*4,
0);
- msleep(1);
+ usleep_range(1000, 2000);
}
}
- /* anything 10 and over uses the bmac */
+ /* Anything 10 and over uses the bmac */
link_10g_plus = (vars->line_speed >= SPEED_10000);
bnx2x_link_int_ack(params, vars, link_10g_plus);
{
bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_1,
MISC_REGISTERS_GPIO_OUTPUT_LOW, port);
- msleep(1);
+ usleep_range(1000, 2000);
bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_1,
MISC_REGISTERS_GPIO_OUTPUT_HIGH, port);
}
MDIO_PMA_REG_GEN_CTRL,
0x0001);
- /* ucode reboot and rst */
+ /* Ucode reboot and rst */
bnx2x_cl45_write(bp, phy,
MDIO_PMA_DEVAD,
MDIO_PMA_REG_GEN_CTRL,
MDIO_PMA_DEVAD,
MDIO_PMA_REG_M8051_MSGOUT_REG, &fw_msgout);
- msleep(1);
+ usleep_range(1000, 2000);
} while (fw_ver1 == 0 || fw_ver1 == 0x4321 ||
((fw_msgout & 0xff) != 0x03 && (phy->type ==
PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073)));
"XAUI workaround has completed\n");
return 0;
}
- msleep(3);
+ usleep_range(3000, 6000);
}
break;
}
- msleep(3);
+ usleep_range(3000, 6000);
}
DP(NETIF_MSG_LINK, "Warning: XAUI work-around timeout !!!\n");
return -EINVAL;
bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_1,
MISC_REGISTERS_GPIO_OUTPUT_HIGH, gpio_port);
- /* enable LASI */
+ /* Enable LASI */
bnx2x_cl45_write(bp, phy,
MDIO_PMA_DEVAD, MDIO_PMA_LASI_RXCTRL, (1<<2));
bnx2x_cl45_write(bp, phy,
DP(NETIF_MSG_LINK, "8703 LASI status 0x%x\n", val1);
- /* clear the interrupt LASI status register */
+ /* Clear the interrupt LASI status register */
bnx2x_cl45_read(bp, phy,
MDIO_PCS_DEVAD, MDIO_PCS_REG_STATUS, &val2);
bnx2x_cl45_read(bp, phy,
if ((val & MDIO_PMA_REG_SFP_TWO_WIRE_CTRL_STATUS_MASK) ==
MDIO_PMA_REG_SFP_TWO_WIRE_STATUS_IDLE)
return 0;
- msleep(1);
+ usleep_range(1000, 2000);
}
return -EINVAL;
}
/* Wait appropriate time for two-wire command to finish before
* polling the status register
*/
- msleep(1);
+ usleep_range(1000, 2000);
/* Wait up to 500us for command complete status */
for (i = 0; i < 100; i++) {
if ((val & MDIO_PMA_REG_SFP_TWO_WIRE_CTRL_STATUS_MASK) ==
MDIO_PMA_REG_SFP_TWO_WIRE_STATUS_IDLE)
return 0;
- msleep(1);
+ usleep_range(1000, 2000);
}
return -EINVAL;
return 0;
}
- /* format the warning message */
+ /* Format the warning message */
if (bnx2x_read_sfp_module_eeprom(phy,
params,
SFP_EEPROM_VENDOR_NAME_ADDR,
timeout * 5);
return 0;
}
- msleep(5);
+ usleep_range(5000, 10000);
}
return -EINVAL;
}
DP(NETIF_MSG_LINK, "Failed to get valid module type\n");
return -EINVAL;
} else if (bnx2x_verify_sfp_module(phy, params) != 0) {
- /* check SFP+ module compatibility */
+ /* Check SFP+ module compatibility */
DP(NETIF_MSG_LINK, "Module verification failed!!\n");
rc = -EINVAL;
/* Turn on fault module-detected led */
bnx2x_sfp_mask_fault(bp, phy, MDIO_PMA_LASI_TXSTAT,
MDIO_PMA_LASI_TXCTRL);
- /* clear LASI indication*/
+ /* Clear LASI indication*/
bnx2x_cl45_read(bp, phy,
MDIO_PMA_DEVAD, MDIO_PMA_LASI_STAT, &val1);
bnx2x_cl45_read(bp, phy,
MDIO_PMA_DEVAD, MDIO_PMA_REG_ROM_VER1, &val);
if (val)
break;
- msleep(10);
+ usleep_range(10000, 20000);
}
DP(NETIF_MSG_LINK, "XGXS 8706 is initialized after %d ms\n", cnt);
if ((params->feature_config_flags &
MDIO_PMA_REG_GEN_CTRL,
MDIO_PMA_REG_GEN_CTRL_ROM_RESET_INTERNAL_MP);
- /* wait for 150ms for microcode load */
+ /* Wait for 150ms for microcode load */
msleep(150);
/* Disable serial boot control, tristates pins SS_N, SCK, MOSI, MISO */
lasi_ctrl_val = 0x0006;
DP(NETIF_MSG_LINK, "Initializing BCM8727\n");
- /* enable LASI */
+ /* Enable LASI */
bnx2x_cl45_write(bp, phy,
MDIO_PMA_DEVAD, MDIO_PMA_LASI_RXCTRL,
rx_alarm_ctrl_val);
MDIO_84833_CMD_HDLR_STATUS, &val);
if (val == PHY84833_STATUS_CMD_OPEN_FOR_CMDS)
break;
- msleep(1);
+ usleep_range(1000, 2000);
}
if (idx >= PHY84833_CMDHDLR_WAIT) {
DP(NETIF_MSG_LINK, "FW cmd: FW not ready.\n");
if ((val == PHY84833_STATUS_CMD_COMPLETE_PASS) ||
(val == PHY84833_STATUS_CMD_COMPLETE_ERROR))
break;
- msleep(1);
+ usleep_range(1000, 2000);
}
if ((idx >= PHY84833_CMDHDLR_WAIT) ||
(val == PHY84833_STATUS_CMD_COMPLETE_ERROR)) {
/* Prevent Phy from working in EEE and advertising it */
rc = bnx2x_84833_cmd_hdlr(phy, params,
PHY84833_CMD_SET_EEE_MODE, &cmd_args, 1);
- if (rc != 0) {
+ if (rc) {
DP(NETIF_MSG_LINK, "EEE disable failed.\n");
return rc;
}
rc = bnx2x_84833_cmd_hdlr(phy, params,
PHY84833_CMD_SET_EEE_MODE, &cmd_args, 1);
- if (rc != 0) {
+ if (rc) {
DP(NETIF_MSG_LINK, "EEE enable failed.\n");
return rc;
}
u16 cmd_args[PHY84833_CMDHDLR_MAX_ARGS];
int rc = 0;
- msleep(1);
+ usleep_range(1000, 2000);
if (!(CHIP_IS_E1(bp)))
port = BP_PATH(bp);
rc = bnx2x_84833_cmd_hdlr(phy, params,
PHY84833_CMD_SET_EEE_MODE, cmd_args,
PHY84833_CMDHDLR_MAX_ARGS);
- if (rc != 0)
+ if (rc)
DP(NETIF_MSG_LINK, "Cfg AutogrEEEn failed.\n");
}
if (initialize)
vars->eee_status &= ~SHMEM_EEE_REQUESTED_BIT;
rc = bnx2x_8483x_eee_timers(params, vars);
- if (rc != 0) {
+ if (rc) {
DP(NETIF_MSG_LINK, "Failed to configure EEE timers\n");
bnx2x_8483x_disable_eee(phy, params, vars);
return rc;
rc = bnx2x_8483x_enable_eee(phy, params, vars);
else
rc = bnx2x_8483x_disable_eee(phy, params, vars);
- if (rc != 0) {
+ if (rc) {
DP(NETIF_MSG_LINK, "Failed to set EEE advertisment\n");
return rc;
}
}
}
if (link_up) {
- DP(NETIF_MSG_LINK, "BCM84823: link speed is %d\n",
+ DP(NETIF_MSG_LINK, "BCM848x3: link speed is %d\n",
vars->line_speed);
bnx2x_ext_phy_resolve_fc(phy, params, vars);
u32 cfg_pin;
DP(NETIF_MSG_LINK, "54618SE cfg init\n");
- usleep_range(1000, 1000);
+ usleep_range(1000, 2000);
/* This works with E3 only, no need to check the chip
* before determining the port.
MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH)
fc_val |= MDIO_AN_REG_ADV_PAUSE_PAUSE;
- /* read all advertisement */
+ /* Read all advertisement */
bnx2x_cl22_read(bp, phy,
0x09,
&an_1000_val);
0x09,
&an_1000_val);
- /* set 100 speed advertisement */
+ /* Set 100 speed advertisement */
if (((phy->req_line_speed == SPEED_AUTO_NEG) &&
(phy->speed_cap_mask &
(PORT_HW_CFG_SPEED_CAPABILITY_D0_100M_FULL |
DP(NETIF_MSG_LINK, "Advertising 100M\n");
}
- /* set 10 speed advertisement */
+ /* Set 10 speed advertisement */
if (((phy->req_line_speed == SPEED_AUTO_NEG) &&
(phy->speed_cap_mask &
(PORT_HW_CFG_SPEED_CAPABILITY_D0_10M_FULL |
DP(NETIF_MSG_LINK, "10G-base-T PMA status 0x%x->0x%x\n",
val2, val1);
link_up = ((val1 & 4) == 4);
- /* if link is up print the AN outcome of the SFX7101 PHY */
+ /* If link is up print the AN outcome of the SFX7101 PHY */
if (link_up) {
bnx2x_cl45_read(bp, phy,
MDIO_AN_DEVAD, MDIO_AN_REG_MASTER_STATUS,
bnx2x_ext_phy_10G_an_resolve(bp, phy, vars);
bnx2x_ext_phy_resolve_fc(phy, params, vars);
- /* read LP advertised speeds */
+ /* Read LP advertised speeds */
if (val2 & (1<<11))
vars->link_status |=
LINK_STATUS_LINK_PARTNER_10GXFD_CAPABLE;
vars->mac_type = MAC_TYPE_NONE;
vars->phy_flags = 0;
- /* disable attentions */
+ /* Disable attentions */
bnx2x_bits_dis(bp, NIG_REG_MASK_INTERRUPT_PORT0 + params->port*4,
(NIG_MASK_XGXS0_LINK_STATUS |
NIG_MASK_XGXS0_LINK10G |
struct bnx2x *bp = params->bp;
u8 phy_index, port = params->port, clear_latch_ind = 0;
DP(NETIF_MSG_LINK, "Resetting the link of port %d\n", port);
- /* disable attentions */
+ /* Disable attentions */
vars->link_status = 0;
bnx2x_update_mng(params, vars->link_status);
vars->eee_status &= ~(SHMEM_EEE_LP_ADV_STATUS_MASK |
NIG_MASK_SERDES0_LINK_STATUS |
NIG_MASK_MI_INT));
- /* activate nig drain */
+ /* Activate nig drain */
REG_WR(bp, NIG_REG_EGRESS_DRAIN0_MODE + port*4, 1);
- /* disable nig egress interface */
+ /* Disable nig egress interface */
if (!CHIP_IS_E3(bp)) {
REG_WR(bp, NIG_REG_BMAC0_OUT_EN + port*4, 0);
REG_WR(bp, NIG_REG_EGRESS_EMAC0_OUT_EN + port*4, 0);
bnx2x_xmac_disable(params);
bnx2x_umac_disable(params);
}
- /* disable emac */
+ /* Disable emac */
if (!CHIP_IS_E3(bp))
REG_WR(bp, NIG_REG_NIG_EMAC0_EN + port*4, 0);
- msleep(10);
+ usleep_range(10000, 20000);
/* The PHY reset is controlled by GPIO 1
* Hold it as vars low
*/
- /* clear link led */
+ /* Clear link led */
bnx2x_set_mdio_clk(bp, params->chip_id, port);
bnx2x_set_led(params, vars, LED_MODE_OFF, 0);
params->phy[INT_PHY].link_reset(
¶ms->phy[INT_PHY], params);
- /* disable nig ingress interface */
+ /* Disable nig ingress interface */
if (!CHIP_IS_E3(bp)) {
- /* reset BigMac */
+ /* Reset BigMac */
REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_2_CLEAR,
(MISC_REGISTERS_RESET_REG_2_RST_BMAC0 << port));
REG_WR(bp, NIG_REG_BMAC0_IN_EN + port*4, 0);
DP(NETIF_MSG_LINK, "populate_phy failed\n");
return -EINVAL;
}
- /* disable attentions */
+ /* Disable attentions */
bnx2x_bits_dis(bp, NIG_REG_MASK_INTERRUPT_PORT0 +
port_of_path*4,
(NIG_MASK_XGXS0_LINK_STATUS |
bnx2x_cl45_write(bp, phy_blk[port],
MDIO_PMA_DEVAD,
MDIO_PMA_REG_TX_POWER_DOWN, (val & (~(1<<10))));
- msleep(15);
+ usleep_range(15000, 30000);
/* Read modify write the SPI-ROM version select register */
bnx2x_cl45_read(bp, phy_blk[port],
REG_WR(bp, MISC_REG_GPIO_EVENT_EN, val);
bnx2x_ext_phy_hw_reset(bp, 0);
- msleep(5);
+ usleep_range(5000, 10000);
for (port = 0; port < PORT_MAX; port++) {
u32 shmem_base, shmem2_base;
/* Initiate PHY reset*/
bnx2x_set_gpio(bp, reset_gpio, MISC_REGISTERS_GPIO_OUTPUT_LOW,
port);
- msleep(1);
+ usleep_range(1000, 2000);
bnx2x_set_gpio(bp, reset_gpio, MISC_REGISTERS_GPIO_OUTPUT_HIGH,
port);
- msleep(5);
+ usleep_range(5000, 10000);
/* PART1 - Reset both phys */
for (port = PORT_MAX - 1; port >= PORT_0; port--) {
MDIO_PMA_REG_CTRL, &val);
if (!(val & (1<<15)))
break;
- msleep(1);
+ usleep_range(1000, 2000);
}
if (cnt >= 1500) {
DP(NETIF_MSG_LINK, "84833 reset timeout\n");
break;
}
- if (rc != 0)
+ if (rc)
netdev_err(bp->dev, "Warning: PHY was not initialized,"
" Port %d\n",
0);
projects / platform / upstream / kernel-adaptation-pc.git / commitdiff