[MIPS] BCM1480: Fix PCI/HT IO access

- removed check for enable HT-PCI bridges, because some CFE version
  init only the needed one and scanning works even with disabled HT
  links
- implemented I/O access behind HT PCI busses
- fixed pci_map for IO resource behind PCI bridge

Tested with E100 and Tulip driver.

Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

diff --git a/arch/mips/pci/pci-bcm1480.c b/arch/mips/pci/pci-bcm1480.c
index ab68c43..87e2c8f 100644 (file)
--- a/arch/mips/pci/pci-bcm1480.c
+++ b/arch/mips/pci/pci-bcm1480.c
@@ -185,8 +185,8 @@ static struct resource bcm1480_mem_resource = {
 
 static struct resource bcm1480_io_resource = {
        .name   = "BCM1480 PCI I/O",
-       .start  = 0x2c000000UL,
-       .end    = 0x2dffffffUL,
+       .start  = A_BCM1480_PHYS_PCI_IO_MATCH_BYTES,
+       .end    = A_BCM1480_PHYS_PCI_IO_MATCH_BYTES + 0x1ffffffUL,
        .flags  = IORESOURCE_IO,
 };
 
@@ -194,6 +194,7 @@ struct pci_controller bcm1480_controller = {
        .pci_ops        = &bcm1480_pci_ops,
        .mem_resource   = &bcm1480_mem_resource,
        .io_resource    = &bcm1480_io_resource,
+       .io_offset      = A_BCM1480_PHYS_PCI_IO_MATCH_BYTES,
 };
 
 
@@ -251,6 +252,7 @@ static int __init bcm1480_pcibios_init(void)
 
        bcm1480_controller.io_map_base = (unsigned long)
                ioremap(A_BCM1480_PHYS_PCI_IO_MATCH_BYTES, 65536);
+       bcm1480_controller.io_map_base -= bcm1480_controller.io_offset;
        set_io_port_base(bcm1480_controller.io_map_base);
        isa_slot_offset = (unsigned long)
                ioremap(A_BCM1480_PHYS_PCI_MEM_MATCH_BYTES, 1024*1024);

diff --git a/arch/mips/pci/pci-bcm1480ht.c b/arch/mips/pci/pci-bcm1480ht.c
index 005e7fe..f54f454 100644 (file)
--- a/arch/mips/pci/pci-bcm1480ht.c
+++ b/arch/mips/pci/pci-bcm1480ht.c
@@ -180,8 +180,8 @@ static struct resource bcm1480ht_mem_resource = {
 
 static struct resource bcm1480ht_io_resource = {
        .name   = "BCM1480 HT I/O",
-       .start  = 0x00000000UL,
-       .end    = 0x01ffffffUL,
+       .start  = A_BCM1480_PHYS_HT_IO_MATCH_BYTES,
+       .end    = A_BCM1480_PHYS_HT_IO_MATCH_BYTES + 0x01ffffffUL,
        .flags  = IORESOURCE_IO,
 };
 
@@ -191,29 +191,22 @@ struct pci_controller bcm1480ht_controller = {
        .io_resource    = &bcm1480ht_io_resource,
        .index          = 1,
        .get_busno      = bcm1480ht_pcibios_get_busno,
+       .io_offset      = A_BCM1480_PHYS_HT_IO_MATCH_BYTES,
 };
 
 static int __init bcm1480ht_pcibios_init(void)
 {
-       uint32_t cmdreg;
-
        ht_cfg_space = ioremap(A_BCM1480_PHYS_HT_CFG_MATCH_BITS, 16*1024*1024);
 
-       /*
-        * See if the PCI bus has been configured by the firmware.
-        */
-       cmdreg = READCFG32(CFGOFFSET(0, PCI_DEVFN(PCI_BRIDGE_DEVICE, 0),
-                                    PCI_COMMAND));
-       if (!(cmdreg & PCI_COMMAND_MASTER)) {
-               printk("HT: Skipping HT probe. Bus is not initialized.\n");
-               iounmap(ht_cfg_space);
-               return 1; /* XXX */
-       }
+       /* CFE doesn't always init all HT paths, so we always scan */
        bcm1480ht_bus_status |= PCI_BUS_ENABLED;
 
        ht_eoi_space = (unsigned long)
                ioremap(A_BCM1480_PHYS_HT_SPECIAL_MATCH_BYTES,
                        4 * 1024 * 1024);
+       bcm1480ht_controller.io_map_base = (unsigned long)
+               ioremap(A_BCM1480_PHYS_HT_IO_MATCH_BYTES, 65536);
+       bcm1480ht_controller.io_map_base -= bcm1480ht_controller.io_offset;
 
        register_pci_controller(&bcm1480ht_controller);