#define AR5K_TUNE_MAX_TXPOWER 63
#define AR5K_TUNE_DEFAULT_TXPOWER 25
#define AR5K_TUNE_TPC_TXPOWER false
-#define ATH5K_TUNE_CALIBRATION_INTERVAL_FULL 10000 /* 10 sec */
+#define ATH5K_TUNE_CALIBRATION_INTERVAL_FULL 60000 /* 60 sec */
+#define ATH5K_TUNE_CALIBRATION_INTERVAL_SHORT 10000 /* 10 sec */
#define ATH5K_TUNE_CALIBRATION_INTERVAL_ANI 1000 /* 1 sec */
-#define ATH5K_TUNE_CALIBRATION_INTERVAL_NF 60000 /* 60 sec */
-
#define ATH5K_TX_COMPLETE_POLL_INT 3000 /* 3 sec */
#define AR5K_INIT_CARR_SENSE_EN 1
enum ath5k_calibration_mask {
AR5K_CALIBRATION_FULL = 0x01,
AR5K_CALIBRATION_SHORT = 0x02,
- AR5K_CALIBRATION_ANI = 0x04,
+ AR5K_CALIBRATION_NF = 0x04,
+ AR5K_CALIBRATION_ANI = 0x08,
};
/*
led_on; /* pin setting for LED on */
struct work_struct reset_work; /* deferred chip reset */
+ struct work_struct calib_work; /* deferred phy calibration */
struct list_head rxbuf; /* receive buffer */
spinlock_t rxbuflock;
struct ath5k_rfkill rf_kill;
- struct tasklet_struct calib; /* calibration tasklet */
-
spinlock_t block; /* protects beacon */
struct tasklet_struct beacontq; /* beacon intr tasklet */
struct list_head bcbuf; /* beacon buffer */
enum ath5k_int ah_imr;
struct ieee80211_channel *ah_current_channel;
- bool ah_calibration;
+ bool ah_iq_cal_needed;
bool ah_single_chip;
enum ath5k_version ah_version;
/* Calibration timestamp */
unsigned long ah_cal_next_full;
+ unsigned long ah_cal_next_short;
unsigned long ah_cal_next_ani;
- unsigned long ah_cal_next_nf;
/* Calibration mask */
u8 ah_cal_mask;
ath5k_intr_calibration_poll(struct ath5k_hw *ah)
{
if (time_is_before_eq_jiffies(ah->ah_cal_next_ani) &&
- !(ah->ah_cal_mask & AR5K_CALIBRATION_FULL)) {
- /* run ANI only when full calibration is not active */
+ !(ah->ah_cal_mask & AR5K_CALIBRATION_FULL) &&
+ !(ah->ah_cal_mask & AR5K_CALIBRATION_SHORT)) {
+
+ /* Run ANI only when calibration is not active */
+
ah->ah_cal_next_ani = jiffies +
msecs_to_jiffies(ATH5K_TUNE_CALIBRATION_INTERVAL_ANI);
tasklet_schedule(&ah->ani_tasklet);
- } else if (time_is_before_eq_jiffies(ah->ah_cal_next_full)) {
- ah->ah_cal_next_full = jiffies +
- msecs_to_jiffies(ATH5K_TUNE_CALIBRATION_INTERVAL_FULL);
- tasklet_schedule(&ah->calib);
+ } else if (time_is_before_eq_jiffies(ah->ah_cal_next_short) &&
+ !(ah->ah_cal_mask & AR5K_CALIBRATION_FULL) &&
+ !(ah->ah_cal_mask & AR5K_CALIBRATION_SHORT)) {
+
+ /* Run calibration only when another calibration
+ * is not running.
+ *
+ * Note: This is for both full/short calibration,
+ * if it's time for a full one, ath5k_calibrate_work will deal
+ * with it. */
+
+ ah->ah_cal_next_short = jiffies +
+ msecs_to_jiffies(ATH5K_TUNE_CALIBRATION_INTERVAL_SHORT);
+ ieee80211_queue_work(ah->hw, &ah->calib_work);
}
/* we could use SWI to generate enough interrupts to meet our
* calibration interval requirements, if necessary:
* for temperature/environment changes.
*/
static void
-ath5k_tasklet_calibrate(unsigned long data)
+ath5k_calibrate_work(struct work_struct *work)
{
- struct ath5k_hw *ah = (void *)data;
+ struct ath5k_hw *ah = container_of(work, struct ath5k_hw,
+ calib_work);
+
+ /* Should we run a full calibration ? */
+ if (time_is_before_eq_jiffies(ah->ah_cal_next_full)) {
+
+ ah->ah_cal_next_full = jiffies +
+ msecs_to_jiffies(ATH5K_TUNE_CALIBRATION_INTERVAL_FULL);
+ ah->ah_cal_mask |= AR5K_CALIBRATION_FULL;
+
+ ATH5K_DBG(ah, ATH5K_DEBUG_CALIBRATE,
+ "running full calibration\n");
+
+ if (ath5k_hw_gainf_calibrate(ah) == AR5K_RFGAIN_NEED_CHANGE) {
+ /*
+ * Rfgain is out of bounds, reset the chip
+ * to load new gain values.
+ */
+ ATH5K_DBG(ah, ATH5K_DEBUG_RESET,
+ "got new rfgain, resetting\n");
+ ieee80211_queue_work(ah->hw, &ah->reset_work);
+ }
+
+ /* TODO: On full calibration we should stop TX here,
+ * so that it doesn't interfere (mostly due to gain_f
+ * calibration that messes with tx packets -see phy.c).
+ *
+ * NOTE: Stopping the queues from above is not enough
+ * to stop TX but saves us from disconecting (at least
+ * we don't lose packets). */
+ ieee80211_stop_queues(ah->hw);
+ } else
+ ah->ah_cal_mask |= AR5K_CALIBRATION_SHORT;
- /* Only full calibration for now */
- ah->ah_cal_mask |= AR5K_CALIBRATION_FULL;
ATH5K_DBG(ah, ATH5K_DEBUG_CALIBRATE, "channel %u/%x\n",
ieee80211_frequency_to_channel(ah->curchan->center_freq),
ah->curchan->hw_value);
- if (ath5k_hw_gainf_calibrate(ah) == AR5K_RFGAIN_NEED_CHANGE) {
- /*
- * Rfgain is out of bounds, reset the chip
- * to load new gain values.
- */
- ATH5K_DBG(ah, ATH5K_DEBUG_RESET, "calibration, resetting\n");
- ieee80211_queue_work(ah->hw, &ah->reset_work);
- }
if (ath5k_hw_phy_calibrate(ah, ah->curchan))
ATH5K_ERR(ah, "calibration of channel %u failed\n",
ieee80211_frequency_to_channel(
ah->curchan->center_freq));
- /* Noise floor calibration interrupts rx/tx path while I/Q calibration
- * doesn't.
- * TODO: We should stop TX here, so that it doesn't interfere.
- * Note that stopping the queues is not enough to stop TX! */
- if (time_is_before_eq_jiffies(ah->ah_cal_next_nf)) {
- ah->ah_cal_next_nf = jiffies +
- msecs_to_jiffies(ATH5K_TUNE_CALIBRATION_INTERVAL_NF);
- ath5k_hw_update_noise_floor(ah);
- }
-
- ah->ah_cal_mask &= ~AR5K_CALIBRATION_FULL;
+ /* Clear calibration flags */
+ if (ah->ah_cal_mask & AR5K_CALIBRATION_FULL) {
+ ieee80211_wake_queues(ah->hw);
+ ah->ah_cal_mask &= ~AR5K_CALIBRATION_FULL;
+ } else if (ah->ah_cal_mask & AR5K_CALIBRATION_SHORT)
+ ah->ah_cal_mask &= ~AR5K_CALIBRATION_SHORT;
}
ah->tx_pending = false;
tasklet_kill(&ah->rxtq);
tasklet_kill(&ah->txtq);
- tasklet_kill(&ah->calib);
tasklet_kill(&ah->beacontq);
tasklet_kill(&ah->ani_tasklet);
}
ath5k_ani_init(ah, ani_mode);
- ah->ah_cal_next_full = jiffies + msecs_to_jiffies(100);
- ah->ah_cal_next_ani = jiffies;
- ah->ah_cal_next_nf = jiffies;
+ /*
+ * Set calibration intervals
+ *
+ * Note: We don't need to run calibration imediately
+ * since some initial calibration is done on reset
+ * even for fast channel switching. Also on scanning
+ * this will get set again and again and it won't get
+ * executed unless we connect somewhere and spend some
+ * time on the channel (that's what calibration needs
+ * anyway to be accurate).
+ */
+ ah->ah_cal_next_full = jiffies +
+ msecs_to_jiffies(ATH5K_TUNE_CALIBRATION_INTERVAL_FULL);
+ ah->ah_cal_next_ani = jiffies +
+ msecs_to_jiffies(ATH5K_TUNE_CALIBRATION_INTERVAL_ANI);
+ ah->ah_cal_next_short = jiffies +
+ msecs_to_jiffies(ATH5K_TUNE_CALIBRATION_INTERVAL_SHORT);
+
ewma_init(&ah->ah_beacon_rssi_avg, 1024, 8);
/* clear survey data and cycle counters */
tasklet_init(&ah->rxtq, ath5k_tasklet_rx, (unsigned long)ah);
tasklet_init(&ah->txtq, ath5k_tasklet_tx, (unsigned long)ah);
- tasklet_init(&ah->calib, ath5k_tasklet_calibrate, (unsigned long)ah);
tasklet_init(&ah->beacontq, ath5k_tasklet_beacon, (unsigned long)ah);
tasklet_init(&ah->ani_tasklet, ath5k_tasklet_ani, (unsigned long)ah);
INIT_WORK(&ah->reset_work, ath5k_reset_work);
+ INIT_WORK(&ah->calib_work, ath5k_calibrate_work);
INIT_DELAYED_WORK(&ah->tx_complete_work, ath5k_tx_complete_poll_work);
ret = ath5k_hw_common(ah)->bus_ops->eeprom_read_mac(ah, mac);
* And this is the MadWiFi bug entry related to the above
* http://madwifi-project.org/ticket/1659
* with various measurements and diagrams
- *
- * TODO: Deal with power drops due to probes by setting an appropriate
- * tx power on the probe packets ! Make this part of the calibration process.
*/
/* Initialize ah_gain during attach */
* tx power and a Peak to Average Power Detector (PAPD) will try
* to measure the gain.
*
- * XXX: How about forcing a tx packet (bypassing PCU arbitrator etc)
+ * TODO: Force a tx packet (bypassing PCU arbitrator etc)
* just after we enable the probe so that we don't mess with
- * standard traffic ? Maybe it's time to use sw interrupts and
- * a probe tasklet !!!
+ * standard traffic.
*/
static void ath5k_hw_request_rfgain_probe(struct ath5k_hw *ah)
{
/* Main callback for thermal RF gain calibration engine
* Check for a new gain reading and schedule an adjustment
* if needed.
- *
- * TODO: Use sw interrupt to schedule reset if gain_F needs
- * adjustment */
+ */
enum ath5k_rfgain ath5k_hw_gainf_calibrate(struct ath5k_hw *ah)
{
u32 data, type;
return;
}
+ ah->ah_cal_mask |= AR5K_CALIBRATION_NF;
+
ee_mode = ath5k_eeprom_mode_from_channel(ah->ah_current_channel);
/* completed NF calibration, test threshold */
ah->ah_noise_floor = nf;
+ ah->ah_cal_mask &= ~AR5K_CALIBRATION_NF;
+
ATH5K_DBG(ah, ATH5K_DEBUG_CALIBRATE,
"noise floor calibrated: %d\n", nf);
}
s32 iq_corr, i_coff, i_coffd, q_coff, q_coffd;
int i;
- if (!ah->ah_calibration ||
- ath5k_hw_reg_read(ah, AR5K_PHY_IQ) & AR5K_PHY_IQ_RUN)
- return 0;
+ /* Skip if I/Q calibration is not needed or if it's still running */
+ if (!ah->ah_iq_cal_needed)
+ return -EINVAL;
+ else if (ath5k_hw_reg_read(ah, AR5K_PHY_IQ) & AR5K_PHY_IQ_RUN) {
+ ATH5K_DBG_UNLIMIT(ah, ATH5K_DEBUG_CALIBRATE,
+ "I/Q calibration still running");
+ return -EBUSY;
+ }
/* Calibration has finished, get the results and re-run */
- /* work around empty results which can apparently happen on 5212 */
+
+ /* Work around for empty results which can apparently happen on 5212:
+ * Read registers up to 10 times until we get both i_pr and q_pwr */
for (i = 0; i <= 10; i++) {
iq_corr = ath5k_hw_reg_read(ah, AR5K_PHY_IQRES_CAL_CORR);
i_pwr = ath5k_hw_reg_read(ah, AR5K_PHY_IQRES_CAL_PWR_I);
else
q_coffd = q_pwr >> 7;
- /* protect against divide by 0 and loss of sign bits */
+ /* In case i_coffd became zero, cancel calibration
+ * not only it's too small, it'll also result a divide
+ * by zero later on. */
if (i_coffd == 0 || q_coffd < 2)
- return 0;
+ return -ECANCELED;
+
+ /* Protect against loss of sign bits */
i_coff = (-iq_corr) / i_coffd;
i_coff = clamp(i_coff, -32, 31); /* signed 6 bit */
return ath5k_hw_rf5110_calibrate(ah, channel);
ret = ath5k_hw_rf511x_iq_calibrate(ah);
+ if (ret) {
+ ATH5K_DBG_UNLIMIT(ah, ATH5K_DEBUG_CALIBRATE,
+ "No I/Q correction performed (%uMHz)\n",
+ channel->center_freq);
+
+ /* Happens all the time if there is not much
+ * traffic, consider it normal behaviour. */
+ ret = 0;
+ }
+
+ /* On full calibration do an AGC calibration and
+ * request a PAPD probe for gainf calibration if
+ * needed */
+ if (ah->ah_cal_mask & AR5K_CALIBRATION_FULL) {
+
+ AR5K_REG_ENABLE_BITS(ah, AR5K_PHY_AGCCTL,
+ AR5K_PHY_AGCCTL_CAL);
+
+ ret = ath5k_hw_register_timeout(ah, AR5K_PHY_AGCCTL,
+ AR5K_PHY_AGCCTL_CAL | AR5K_PHY_AGCCTL_NF,
+ 0, false);
+ if (ret) {
+ ATH5K_ERR(ah,
+ "gain calibration timeout (%uMHz)\n",
+ channel->center_freq);
+ }
+
+ if ((ah->ah_radio == AR5K_RF5111 ||
+ ah->ah_radio == AR5K_RF5112)
+ && (channel->hw_value != AR5K_MODE_11B))
+ ath5k_hw_request_rfgain_probe(ah);
+ }
- if ((ah->ah_radio == AR5K_RF5111 || ah->ah_radio == AR5K_RF5112) &&
- (channel->hw_value != AR5K_MODE_11B))
- ath5k_hw_request_rfgain_probe(ah);
+ /* Update noise floor
+ * XXX: Only do this after AGC calibration */
+ if (!(ah->ah_cal_mask & AR5K_CALIBRATION_NF))
+ ath5k_hw_update_noise_floor(ah);
return ret;
}
/* At the same time start I/Q calibration for QAM constellation
* -no need for CCK- */
- ah->ah_calibration = false;
+ ah->ah_iq_cal_needed = false;
if (!(mode == AR5K_MODE_11B)) {
- ah->ah_calibration = true;
+ ah->ah_iq_cal_needed = true;
AR5K_REG_WRITE_BITS(ah, AR5K_PHY_IQ,
AR5K_PHY_IQ_CAL_NUM_LOG_MAX, 15);
AR5K_REG_ENABLE_BITS(ah, AR5K_PHY_IQ,
projects / platform / kernel / linux-exynos.git / commitdiff