-/* Copyright 2008-2009 Broadcom Corporation
+/* Copyright 2008-2011 Broadcom Corporation
*
* Unless you and Broadcom execute a separate written software license
* agreement governing use of this software, this software is licensed to you
/********************************************************/
#define ETH_HLEN 14
-#define ETH_OVREHEAD (ETH_HLEN + 8 + 8)/* 16 for CRC + VLAN + LLC */
+/* L2 header size + 2*VLANs (8 bytes) + LLC SNAP (8 bytes) */
+#define ETH_OVREHEAD (ETH_HLEN + 8 + 8)
#define ETH_MIN_PACKET_SIZE 60
#define ETH_MAX_PACKET_SIZE 1500
#define ETH_MAX_JUMBO_PACKET_SIZE 9600
#define MDIO_ACCESS_TIMEOUT 1000
-#define BMAC_CONTROL_RX_ENABLE 2
+#define BMAC_CONTROL_RX_ENABLE 2
/***********************************************************/
/* Shortcut definitions */
#define AUTONEG_CL37 SHARED_HW_CFG_AN_ENABLE_CL37
#define AUTONEG_CL73 SHARED_HW_CFG_AN_ENABLE_CL73
-#define AUTONEG_BAM SHARED_HW_CFG_AN_ENABLE_BAM
+#define AUTONEG_BAM SHARED_HW_CFG_AN_ENABLE_BAM
#define AUTONEG_PARALLEL \
SHARED_HW_CFG_AN_ENABLE_PARALLEL_DETECTION
#define AUTONEG_SGMII_FIBER_AUTODET \
#define GP_STATUS_10G_KX4 \
MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_10G_KX4
-#define LINK_10THD LINK_STATUS_SPEED_AND_DUPLEX_10THD
-#define LINK_10TFD LINK_STATUS_SPEED_AND_DUPLEX_10TFD
+#define LINK_10THD LINK_STATUS_SPEED_AND_DUPLEX_10THD
+#define LINK_10TFD LINK_STATUS_SPEED_AND_DUPLEX_10TFD
#define LINK_100TXHD LINK_STATUS_SPEED_AND_DUPLEX_100TXHD
-#define LINK_100T4 LINK_STATUS_SPEED_AND_DUPLEX_100T4
+#define LINK_100T4 LINK_STATUS_SPEED_AND_DUPLEX_100T4
#define LINK_100TXFD LINK_STATUS_SPEED_AND_DUPLEX_100TXFD
#define LINK_1000THD LINK_STATUS_SPEED_AND_DUPLEX_1000THD
#define LINK_1000TFD LINK_STATUS_SPEED_AND_DUPLEX_1000TFD
#define LINK_2500THD LINK_STATUS_SPEED_AND_DUPLEX_2500THD
#define LINK_2500TFD LINK_STATUS_SPEED_AND_DUPLEX_2500TFD
#define LINK_2500XFD LINK_STATUS_SPEED_AND_DUPLEX_2500XFD
-#define LINK_10GTFD LINK_STATUS_SPEED_AND_DUPLEX_10GTFD
-#define LINK_10GXFD LINK_STATUS_SPEED_AND_DUPLEX_10GXFD
-#define LINK_12GTFD LINK_STATUS_SPEED_AND_DUPLEX_12GTFD
-#define LINK_12GXFD LINK_STATUS_SPEED_AND_DUPLEX_12GXFD
+#define LINK_10GTFD LINK_STATUS_SPEED_AND_DUPLEX_10GTFD
+#define LINK_10GXFD LINK_STATUS_SPEED_AND_DUPLEX_10GXFD
+#define LINK_12GTFD LINK_STATUS_SPEED_AND_DUPLEX_12GTFD
+#define LINK_12GXFD LINK_STATUS_SPEED_AND_DUPLEX_12GXFD
#define LINK_12_5GTFD LINK_STATUS_SPEED_AND_DUPLEX_12_5GTFD
#define LINK_12_5GXFD LINK_STATUS_SPEED_AND_DUPLEX_12_5GXFD
-#define LINK_13GTFD LINK_STATUS_SPEED_AND_DUPLEX_13GTFD
-#define LINK_13GXFD LINK_STATUS_SPEED_AND_DUPLEX_13GXFD
-#define LINK_15GTFD LINK_STATUS_SPEED_AND_DUPLEX_15GTFD
-#define LINK_15GXFD LINK_STATUS_SPEED_AND_DUPLEX_15GXFD
-#define LINK_16GTFD LINK_STATUS_SPEED_AND_DUPLEX_16GTFD
-#define LINK_16GXFD LINK_STATUS_SPEED_AND_DUPLEX_16GXFD
+#define LINK_13GTFD LINK_STATUS_SPEED_AND_DUPLEX_13GTFD
+#define LINK_13GXFD LINK_STATUS_SPEED_AND_DUPLEX_13GXFD
+#define LINK_15GTFD LINK_STATUS_SPEED_AND_DUPLEX_15GTFD
+#define LINK_15GXFD LINK_STATUS_SPEED_AND_DUPLEX_15GXFD
+#define LINK_16GTFD LINK_STATUS_SPEED_AND_DUPLEX_16GTFD
+#define LINK_16GXFD LINK_STATUS_SPEED_AND_DUPLEX_16GXFD
#define PHY_XGXS_FLAG 0x1
#define PHY_SGMII_FLAG 0x2
/* */
#define SFP_EEPROM_CON_TYPE_ADDR 0x2
- #define SFP_EEPROM_CON_TYPE_VAL_LC 0x7
+ #define SFP_EEPROM_CON_TYPE_VAL_LC 0x7
#define SFP_EEPROM_CON_TYPE_VAL_COPPER 0x21
#define SFP_EEPROM_FC_TX_TECH_ADDR 0x8
#define SFP_EEPROM_FC_TX_TECH_BITMASK_COPPER_PASSIVE 0x4
- #define SFP_EEPROM_FC_TX_TECH_BITMASK_COPPER_ACTIVE 0x8
+ #define SFP_EEPROM_FC_TX_TECH_BITMASK_COPPER_ACTIVE 0x8
-#define SFP_EEPROM_OPTIONS_ADDR 0x40
+#define SFP_EEPROM_OPTIONS_ADDR 0x40
#define SFP_EEPROM_OPTIONS_LINEAR_RX_OUT_MASK 0x1
-#define SFP_EEPROM_OPTIONS_SIZE 2
+#define SFP_EEPROM_OPTIONS_SIZE 2
-#define EDC_MODE_LINEAR 0x0022
-#define EDC_MODE_LIMITING 0x0044
-#define EDC_MODE_PASSIVE_DAC 0x0055
+#define EDC_MODE_LINEAR 0x0022
+#define EDC_MODE_LIMITING 0x0044
+#define EDC_MODE_PASSIVE_DAC 0x0055
#define ETS_BW_LIMIT_CREDIT_UPPER_BOUND (0x5000)
if ((0 == total_bw) ||
(0 == cos0_bw) ||
(0 == cos1_bw)) {
- DP(NETIF_MSG_LINK,
- "bnx2x_ets_bw_limit: Total BW can't be zero\n");
+ DP(NETIF_MSG_LINK, "Total BW can't be zero\n");
return;
}
/* MAC/PBF section */
/******************************************************************/
static void bnx2x_emac_init(struct link_params *params,
- struct link_vars *vars)
+ struct link_vars *vars)
{
/* reset and unreset the emac core */
struct bnx2x *bp = params->bp;
u16 timeout;
REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_2_CLEAR,
- (MISC_REGISTERS_RESET_REG_2_RST_EMAC0_HARD_CORE << port));
+ (MISC_REGISTERS_RESET_REG_2_RST_EMAC0_HARD_CORE << port));
udelay(5);
REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_2_SET,
- (MISC_REGISTERS_RESET_REG_2_RST_EMAC0_HARD_CORE << port));
+ (MISC_REGISTERS_RESET_REG_2_RST_EMAC0_HARD_CORE << port));
/* init emac - use read-modify-write */
/* self clear reset */
}
static u8 bnx2x_emac_enable(struct link_params *params,
- struct link_vars *vars, u8 lb)
+ struct link_vars *vars, u8 lb)
{
struct bnx2x *bp = params->bp;
u8 port = params->port;
if (CHIP_REV_IS_EMUL(bp)) {
/* Use lane 1 (of lanes 0-3) */
REG_WR(bp, NIG_REG_XGXS_LANE_SEL_P0 + port*4, 1);
- REG_WR(bp, NIG_REG_XGXS_SERDES0_MODE_SEL +
- port*4, 1);
+ REG_WR(bp, NIG_REG_XGXS_SERDES0_MODE_SEL + port*4, 1);
}
/* for fpga */
else
DP(NETIF_MSG_LINK, "bnx2x_emac_enable: Setting FPGA\n");
REG_WR(bp, NIG_REG_XGXS_LANE_SEL_P0 + port*4, 1);
- REG_WR(bp, NIG_REG_XGXS_SERDES0_MODE_SEL + port*4,
- 0);
+ REG_WR(bp, NIG_REG_XGXS_SERDES0_MODE_SEL + port*4, 0);
} else
/* ASIC */
if (vars->phy_flags & PHY_XGXS_FLAG) {
u32 ser_lane = ((params->lane_config &
- PORT_HW_CFG_LANE_SWAP_CFG_MASTER_MASK) >>
- PORT_HW_CFG_LANE_SWAP_CFG_MASTER_SHIFT);
+ PORT_HW_CFG_LANE_SWAP_CFG_MASTER_MASK) >>
+ PORT_HW_CFG_LANE_SWAP_CFG_MASTER_SHIFT);
DP(NETIF_MSG_LINK, "XGXS\n");
/* select the master lanes (out of 0-3) */
- REG_WR(bp, NIG_REG_XGXS_LANE_SEL_P0 +
- port*4, ser_lane);
+ REG_WR(bp, NIG_REG_XGXS_LANE_SEL_P0 + port*4, ser_lane);
/* select XGXS */
- REG_WR(bp, NIG_REG_XGXS_SERDES0_MODE_SEL +
- port*4, 1);
+ REG_WR(bp, NIG_REG_XGXS_SERDES0_MODE_SEL + port*4, 1);
} else { /* SerDes */
DP(NETIF_MSG_LINK, "SerDes\n");
/* select SerDes */
- REG_WR(bp, NIG_REG_XGXS_SERDES0_MODE_SEL +
- port*4, 0);
+ REG_WR(bp, NIG_REG_XGXS_SERDES0_MODE_SEL + port*4, 0);
}
bnx2x_bits_en(bp, emac_base + EMAC_REG_EMAC_RX_MODE,
- EMAC_RX_MODE_RESET);
+ EMAC_RX_MODE_RESET);
bnx2x_bits_en(bp, emac_base + EMAC_REG_EMAC_TX_MODE,
- EMAC_TX_MODE_RESET);
+ EMAC_TX_MODE_RESET);
if (CHIP_REV_IS_SLOW(bp)) {
/* config GMII mode */
val = REG_RD(bp, emac_base + EMAC_REG_EMAC_MODE);
- EMAC_WR(bp, EMAC_REG_EMAC_MODE,
- (val | EMAC_MODE_PORT_GMII));
+ EMAC_WR(bp, EMAC_REG_EMAC_MODE, (val | EMAC_MODE_PORT_GMII));
} else { /* ASIC */
/* pause enable/disable */
bnx2x_bits_dis(bp, emac_base + EMAC_REG_EMAC_RX_MODE,
if (CHIP_REV_IS_EMUL(bp)) {
/* take the BigMac out of reset */
- REG_WR(bp,
- GRCBASE_MISC + MISC_REGISTERS_RESET_REG_2_SET,
- (MISC_REGISTERS_RESET_REG_2_RST_BMAC0 << port));
+ REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_2_SET,
+ (MISC_REGISTERS_RESET_REG_2_RST_BMAC0 << port));
/* enable access for bmac registers */
REG_WR(bp, NIG_REG_BMAC0_REGS_OUT_EN + port*4, 0x1);
val |= (1<<5);
wb_data[0] = val;
wb_data[1] = 0;
- REG_WR_DMAE(bp, bmac_addr + BIGMAC2_REGISTER_RX_CONTROL,
- wb_data, 2);
+ REG_WR_DMAE(bp, bmac_addr + BIGMAC2_REGISTER_RX_CONTROL, wb_data, 2);
udelay(30);
/* Tx control */
wb_data[0] = val;
wb_data[1] = 0;
REG_WR_DMAE(bp, bmac_addr + BIGMAC2_REGISTER_TX_PAUSE_CONTROL,
- wb_data, 2);
+ wb_data, 2);
/* mac control */
val = 0x3; /* Enable RX and TX */
wb_data[0] = val;
wb_data[1] = 0;
- REG_WR_DMAE(bp, bmac_addr + BIGMAC2_REGISTER_BMAC_CONTROL,
- wb_data, 2);
+ REG_WR_DMAE(bp, bmac_addr + BIGMAC2_REGISTER_BMAC_CONTROL, wb_data, 2);
}
static void bnx2x_update_pfc_brb(struct link_params *params,
static u8 bnx2x_bmac1_enable(struct link_params *params,
struct link_vars *vars,
- u8 is_lb)
+ u8 is_lb)
{
struct bnx2x *bp = params->bp;
u8 port = params->port;
/* XGXS control */
wb_data[0] = 0x3c;
wb_data[1] = 0;
- REG_WR_DMAE(bp, bmac_addr +
- BIGMAC_REGISTER_BMAC_XGXS_CONTROL,
- wb_data, 2);
+ REG_WR_DMAE(bp, bmac_addr + BIGMAC_REGISTER_BMAC_XGXS_CONTROL,
+ wb_data, 2);
/* tx MAC SA */
wb_data[0] = ((params->mac_addr[2] << 24) |
params->mac_addr[5]);
wb_data[1] = ((params->mac_addr[0] << 8) |
params->mac_addr[1]);
- REG_WR_DMAE(bp, bmac_addr + BIGMAC_REGISTER_TX_SOURCE_ADDR,
- wb_data, 2);
+ REG_WR_DMAE(bp, bmac_addr + BIGMAC_REGISTER_TX_SOURCE_ADDR, wb_data, 2);
/* mac control */
val = 0x3;
}
wb_data[0] = val;
wb_data[1] = 0;
- REG_WR_DMAE(bp, bmac_addr + BIGMAC_REGISTER_BMAC_CONTROL,
- wb_data, 2);
+ REG_WR_DMAE(bp, bmac_addr + BIGMAC_REGISTER_BMAC_CONTROL, wb_data, 2);
/* set rx mtu */
wb_data[0] = ETH_MAX_JUMBO_PACKET_SIZE + ETH_OVREHEAD;
wb_data[1] = 0;
- REG_WR_DMAE(bp, bmac_addr + BIGMAC_REGISTER_RX_MAX_SIZE,
- wb_data, 2);
+ REG_WR_DMAE(bp, bmac_addr + BIGMAC_REGISTER_RX_MAX_SIZE, wb_data, 2);
bnx2x_update_pfc_bmac1(params, vars);
/* set tx mtu */
wb_data[0] = ETH_MAX_JUMBO_PACKET_SIZE + ETH_OVREHEAD;
wb_data[1] = 0;
- REG_WR_DMAE(bp, bmac_addr + BIGMAC_REGISTER_TX_MAX_SIZE,
- wb_data, 2);
+ REG_WR_DMAE(bp, bmac_addr + BIGMAC_REGISTER_TX_MAX_SIZE, wb_data, 2);
/* set cnt max size */
wb_data[0] = ETH_MAX_JUMBO_PACKET_SIZE + ETH_OVREHEAD;
wb_data[1] = 0;
- REG_WR_DMAE(bp, bmac_addr + BIGMAC_REGISTER_CNT_MAX_SIZE,
- wb_data, 2);
+ REG_WR_DMAE(bp, bmac_addr + BIGMAC_REGISTER_CNT_MAX_SIZE, wb_data, 2);
/* configure safc */
wb_data[0] = 0x1000200;
if (CHIP_REV_IS_EMUL(bp)) {
wb_data[0] = 0xf000;
wb_data[1] = 0;
- REG_WR_DMAE(bp,
- bmac_addr + BIGMAC_REGISTER_TX_PAUSE_THRESHOLD,
+ REG_WR_DMAE(bp, bmac_addr + BIGMAC_REGISTER_TX_PAUSE_THRESHOLD,
wb_data, 2);
}
wb_data[0] = 0;
wb_data[1] = 0;
- REG_WR_DMAE(bp, bmac_addr + BIGMAC2_REGISTER_BMAC_CONTROL,
- wb_data, 2);
+ REG_WR_DMAE(bp, bmac_addr + BIGMAC2_REGISTER_BMAC_CONTROL, wb_data, 2);
udelay(30);
/* XGXS control: Reset phy HW, MDIO registers, PHY PLL and BMAC */
wb_data[0] = 0x3c;
wb_data[1] = 0;
- REG_WR_DMAE(bp, bmac_addr +
- BIGMAC2_REGISTER_BMAC_XGXS_CONTROL,
- wb_data, 2);
+ REG_WR_DMAE(bp, bmac_addr + BIGMAC2_REGISTER_BMAC_XGXS_CONTROL,
+ wb_data, 2);
udelay(30);
wb_data[1] = ((params->mac_addr[0] << 8) |
params->mac_addr[1]);
REG_WR_DMAE(bp, bmac_addr + BIGMAC2_REGISTER_TX_SOURCE_ADDR,
- wb_data, 2);
+ wb_data, 2);
udelay(30);
wb_data[0] = 0x1000200;
wb_data[1] = 0;
REG_WR_DMAE(bp, bmac_addr + BIGMAC2_REGISTER_RX_LLFC_MSG_FLDS,
- wb_data, 2);
+ wb_data, 2);
udelay(30);
/* set rx mtu */
wb_data[0] = ETH_MAX_JUMBO_PACKET_SIZE + ETH_OVREHEAD;
wb_data[1] = 0;
- REG_WR_DMAE(bp, bmac_addr + BIGMAC2_REGISTER_RX_MAX_SIZE,
- wb_data, 2);
+ REG_WR_DMAE(bp, bmac_addr + BIGMAC2_REGISTER_RX_MAX_SIZE, wb_data, 2);
udelay(30);
/* set tx mtu */
wb_data[0] = ETH_MAX_JUMBO_PACKET_SIZE + ETH_OVREHEAD;
wb_data[1] = 0;
- REG_WR_DMAE(bp, bmac_addr + BIGMAC2_REGISTER_TX_MAX_SIZE,
- wb_data, 2);
+ REG_WR_DMAE(bp, bmac_addr + BIGMAC2_REGISTER_TX_MAX_SIZE, wb_data, 2);
udelay(30);
/* set cnt max size */
wb_data[0] = ETH_MAX_JUMBO_PACKET_SIZE + ETH_OVREHEAD - 2;
wb_data[1] = 0;
- REG_WR_DMAE(bp, bmac_addr + BIGMAC2_REGISTER_CNT_MAX_SIZE,
- wb_data, 2);
+ REG_WR_DMAE(bp, bmac_addr + BIGMAC2_REGISTER_CNT_MAX_SIZE, wb_data, 2);
udelay(30);
bnx2x_update_pfc_bmac2(params, vars, is_lb);
u32 val;
/* reset and unreset the BigMac */
REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_2_CLEAR,
- (MISC_REGISTERS_RESET_REG_2_RST_BMAC0 << port));
+ (MISC_REGISTERS_RESET_REG_2_RST_BMAC0 << port));
msleep(1);
REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_2_SET,
- (MISC_REGISTERS_RESET_REG_2_RST_BMAC0 << port));
+ (MISC_REGISTERS_RESET_REG_2_RST_BMAC0 << port));
/* enable access for bmac registers */
REG_WR(bp, NIG_REG_BMAC0_REGS_OUT_EN + port*4, 0x1);
struct bnx2x *bp = params->bp;
REG_WR(bp, params->shmem_base +
- offsetof(struct shmem_region,
- port_mb[params->port].link_status),
- link_status);
+ offsetof(struct shmem_region,
+ port_mb[params->port].link_status), link_status);
}
static void bnx2x_bmac_rx_disable(struct bnx2x *bp, u8 port)
{
u32 bmac_addr = port ? NIG_REG_INGRESS_BMAC1_MEM :
- NIG_REG_INGRESS_BMAC0_MEM;
+ NIG_REG_INGRESS_BMAC0_MEM;
u32 wb_data[2];
u32 nig_bmac_enable = REG_RD(bp, NIG_REG_BMAC0_REGS_OUT_EN + port*4);
if (CHIP_IS_E2(bp)) {
/* Clear Rx Enable bit in BMAC_CONTROL register */
REG_RD_DMAE(bp, bmac_addr +
- BIGMAC2_REGISTER_BMAC_CONTROL,
- wb_data, 2);
+ BIGMAC2_REGISTER_BMAC_CONTROL,
+ wb_data, 2);
wb_data[0] &= ~BMAC_CONTROL_RX_ENABLE;
REG_WR_DMAE(bp, bmac_addr +
- BIGMAC2_REGISTER_BMAC_CONTROL,
- wb_data, 2);
+ BIGMAC2_REGISTER_BMAC_CONTROL,
+ wb_data, 2);
} else {
/* Clear Rx Enable bit in BMAC_CONTROL register */
REG_RD_DMAE(bp, bmac_addr +
}
static u8 bnx2x_pbf_update(struct link_params *params, u32 flow_ctrl,
- u32 line_speed)
+ u32 line_speed)
{
struct bnx2x *bp = params->bp;
u8 port = params->port;
/* update threshold */
REG_WR(bp, PBF_REG_P0_ARB_THRSH + port*4, 0);
/* update init credit */
- init_crd = 778; /* (800-18-4) */
+ init_crd = 778; /* (800-18-4) */
} else {
u32 thresh = (ETH_MAX_JUMBO_PACKET_SIZE +
for (i = 0; i < 50; i++) {
udelay(10);
- tmp = REG_RD(bp, phy->mdio_ctrl +
- EMAC_REG_EMAC_MDIO_COMM);
+ tmp = REG_RD(bp, phy->mdio_ctrl + EMAC_REG_EMAC_MDIO_COMM);
if (!(tmp & EMAC_MDIO_COMM_START_BUSY)) {
udelay(5);
break;
udelay(10);
tmp = REG_RD(bp, phy->mdio_ctrl +
- EMAC_REG_EMAC_MDIO_COMM);
+ EMAC_REG_EMAC_MDIO_COMM);
if (!(tmp & EMAC_MDIO_COMM_START_BUSY)) {
udelay(5);
break;
saved_mode = REG_RD(bp, phy->mdio_ctrl + EMAC_REG_EMAC_MDIO_MODE);
val = saved_mode & ~((EMAC_MDIO_MODE_AUTO_POLL |
- EMAC_MDIO_MODE_CLOCK_CNT));
+ EMAC_MDIO_MODE_CLOCK_CNT));
val |= (EMAC_MDIO_MODE_CLAUSE_45 |
(49L << EMAC_MDIO_MODE_CLOCK_CNT_BITSHIFT));
REG_WR(bp, phy->mdio_ctrl + EMAC_REG_EMAC_MDIO_MODE, val);
udelay(10);
val = REG_RD(bp, phy->mdio_ctrl +
- EMAC_REG_EMAC_MDIO_COMM);
+ EMAC_REG_EMAC_MDIO_COMM);
if (!(val & EMAC_MDIO_COMM_START_BUSY)) {
*ret_val = (u16)(val & EMAC_MDIO_COMM_DATA);
break;
aer_val = 0x3800 + offset - 1;
else
aer_val = 0x3800 + offset;
- CL45_WR_OVER_CL22(bp, phy,
- MDIO_REG_BANK_AER_BLOCK,
- MDIO_AER_BLOCK_AER_REG, aer_val);
+ CL45_WR_OVER_CL22(bp, phy, MDIO_REG_BANK_AER_BLOCK,
+ MDIO_AER_BLOCK_AER_REG, aer_val);
}
static void bnx2x_set_aer_mmd_serdes(struct bnx2x *bp,
struct bnx2x_phy *phy)
{
CL45_WR_OVER_CL22(bp, phy,
- MDIO_REG_BANK_AER_BLOCK,
- MDIO_AER_BLOCK_AER_REG, 0x3800);
+ MDIO_REG_BANK_AER_BLOCK,
+ MDIO_AER_BLOCK_AER_REG, 0x3800);
}
/******************************************************************/
bnx2x_set_serdes_access(bp, port);
- REG_WR(bp, NIG_REG_SERDES0_CTRL_MD_DEVAD +
- port*0x10,
- DEFAULT_PHY_DEV_ADDR);
+ REG_WR(bp, NIG_REG_SERDES0_CTRL_MD_DEVAD + port*0x10,
+ DEFAULT_PHY_DEV_ADDR);
}
static void bnx2x_xgxs_deassert(struct link_params *params)
udelay(500);
REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_3_SET, val);
- REG_WR(bp, NIG_REG_XGXS0_CTRL_MD_ST +
- port*0x18, 0);
+ REG_WR(bp, NIG_REG_XGXS0_CTRL_MD_ST + port*0x18, 0);
REG_WR(bp, NIG_REG_XGXS0_CTRL_MD_DEVAD + port*0x18,
- params->phy[INT_PHY].def_md_devad);
+ params->phy[INT_PHY].def_md_devad);
}
void bnx2x_link_status_update(struct link_params *params,
- struct link_vars *vars)
+ struct link_vars *vars)
{
struct bnx2x *bp = params->bp;
u8 link_10g;
u8 port = params->port;
vars->link_status = REG_RD(bp, params->shmem_base +
- offsetof(struct shmem_region,
- port_mb[port].link_status));
+ offsetof(struct shmem_region,
+ port_mb[port].link_status));
vars->link_up = (vars->link_status & LINK_STATUS_LINK_UP);
vars->phy_link_up = 1;
vars->duplex = DUPLEX_FULL;
switch (vars->link_status &
- LINK_STATUS_SPEED_AND_DUPLEX_MASK) {
+ LINK_STATUS_SPEED_AND_DUPLEX_MASK) {
case LINK_10THD:
vars->duplex = DUPLEX_HALF;
/* fall thru */
{
struct bnx2x *bp = params->bp;
u16 new_master_ln, ser_lane;
- ser_lane = ((params->lane_config &
+ ser_lane = ((params->lane_config &
PORT_HW_CFG_LANE_SWAP_CFG_MASTER_MASK) >>
- PORT_HW_CFG_LANE_SWAP_CFG_MASTER_SHIFT);
+ PORT_HW_CFG_LANE_SWAP_CFG_MASTER_SHIFT);
/* set the master_ln for AN */
CL45_RD_OVER_CL22(bp, phy,
- MDIO_REG_BANK_XGXS_BLOCK2,
- MDIO_XGXS_BLOCK2_TEST_MODE_LANE,
- &new_master_ln);
+ MDIO_REG_BANK_XGXS_BLOCK2,
+ MDIO_XGXS_BLOCK2_TEST_MODE_LANE,
+ &new_master_ln);
CL45_WR_OVER_CL22(bp, phy,
- MDIO_REG_BANK_XGXS_BLOCK2 ,
- MDIO_XGXS_BLOCK2_TEST_MODE_LANE,
- (new_master_ln | ser_lane));
+ MDIO_REG_BANK_XGXS_BLOCK2 ,
+ MDIO_XGXS_BLOCK2_TEST_MODE_LANE,
+ (new_master_ln | ser_lane));
}
static u8 bnx2x_reset_unicore(struct link_params *params,
u16 i;
CL45_RD_OVER_CL22(bp, phy,
- MDIO_REG_BANK_COMBO_IEEE0,
- MDIO_COMBO_IEEE0_MII_CONTROL, &mii_control);
+ MDIO_REG_BANK_COMBO_IEEE0,
+ MDIO_COMBO_IEEE0_MII_CONTROL, &mii_control);
/* reset the unicore */
CL45_WR_OVER_CL22(bp, phy,
- MDIO_REG_BANK_COMBO_IEEE0,
- MDIO_COMBO_IEEE0_MII_CONTROL,
- (mii_control |
- MDIO_COMBO_IEEO_MII_CONTROL_RESET));
+ MDIO_REG_BANK_COMBO_IEEE0,
+ MDIO_COMBO_IEEE0_MII_CONTROL,
+ (mii_control |
+ MDIO_COMBO_IEEO_MII_CONTROL_RESET));
if (set_serdes)
bnx2x_set_serdes_access(bp, params->port);
/* the reset erased the previous bank value */
CL45_RD_OVER_CL22(bp, phy,
- MDIO_REG_BANK_COMBO_IEEE0,
- MDIO_COMBO_IEEE0_MII_CONTROL,
- &mii_control);
+ MDIO_REG_BANK_COMBO_IEEE0,
+ MDIO_COMBO_IEEE0_MII_CONTROL,
+ &mii_control);
if (!(mii_control & MDIO_COMBO_IEEO_MII_CONTROL_RESET)) {
udelay(5);
u16 ser_lane, rx_lane_swap, tx_lane_swap;
ser_lane = ((params->lane_config &
- PORT_HW_CFG_LANE_SWAP_CFG_MASTER_MASK) >>
- PORT_HW_CFG_LANE_SWAP_CFG_MASTER_SHIFT);
+ PORT_HW_CFG_LANE_SWAP_CFG_MASTER_MASK) >>
+ PORT_HW_CFG_LANE_SWAP_CFG_MASTER_SHIFT);
rx_lane_swap = ((params->lane_config &
- PORT_HW_CFG_LANE_SWAP_CFG_RX_MASK) >>
- PORT_HW_CFG_LANE_SWAP_CFG_RX_SHIFT);
+ PORT_HW_CFG_LANE_SWAP_CFG_RX_MASK) >>
+ PORT_HW_CFG_LANE_SWAP_CFG_RX_SHIFT);
tx_lane_swap = ((params->lane_config &
- PORT_HW_CFG_LANE_SWAP_CFG_TX_MASK) >>
- PORT_HW_CFG_LANE_SWAP_CFG_TX_SHIFT);
+ PORT_HW_CFG_LANE_SWAP_CFG_TX_MASK) >>
+ PORT_HW_CFG_LANE_SWAP_CFG_TX_SHIFT);
if (rx_lane_swap != 0x1b) {
CL45_WR_OVER_CL22(bp, phy,
- MDIO_REG_BANK_XGXS_BLOCK2,
- MDIO_XGXS_BLOCK2_RX_LN_SWAP,
- (rx_lane_swap |
- MDIO_XGXS_BLOCK2_RX_LN_SWAP_ENABLE |
- MDIO_XGXS_BLOCK2_RX_LN_SWAP_FORCE_ENABLE));
+ MDIO_REG_BANK_XGXS_BLOCK2,
+ MDIO_XGXS_BLOCK2_RX_LN_SWAP,
+ (rx_lane_swap |
+ MDIO_XGXS_BLOCK2_RX_LN_SWAP_ENABLE |
+ MDIO_XGXS_BLOCK2_RX_LN_SWAP_FORCE_ENABLE));
} else {
CL45_WR_OVER_CL22(bp, phy,
- MDIO_REG_BANK_XGXS_BLOCK2,
- MDIO_XGXS_BLOCK2_RX_LN_SWAP, 0);
+ MDIO_REG_BANK_XGXS_BLOCK2,
+ MDIO_XGXS_BLOCK2_RX_LN_SWAP, 0);
}
if (tx_lane_swap != 0x1b) {
CL45_WR_OVER_CL22(bp, phy,
- MDIO_REG_BANK_XGXS_BLOCK2,
- MDIO_XGXS_BLOCK2_TX_LN_SWAP,
- (tx_lane_swap |
- MDIO_XGXS_BLOCK2_TX_LN_SWAP_ENABLE));
+ MDIO_REG_BANK_XGXS_BLOCK2,
+ MDIO_XGXS_BLOCK2_TX_LN_SWAP,
+ (tx_lane_swap |
+ MDIO_XGXS_BLOCK2_TX_LN_SWAP_ENABLE));
} else {
CL45_WR_OVER_CL22(bp, phy,
- MDIO_REG_BANK_XGXS_BLOCK2,
- MDIO_XGXS_BLOCK2_TX_LN_SWAP, 0);
+ MDIO_REG_BANK_XGXS_BLOCK2,
+ MDIO_XGXS_BLOCK2_TX_LN_SWAP, 0);
}
}
struct bnx2x *bp = params->bp;
u16 control2;
CL45_RD_OVER_CL22(bp, phy,
- MDIO_REG_BANK_SERDES_DIGITAL,
- MDIO_SERDES_DIGITAL_A_1000X_CONTROL2,
- &control2);
+ MDIO_REG_BANK_SERDES_DIGITAL,
+ MDIO_SERDES_DIGITAL_A_1000X_CONTROL2,
+ &control2);
if (phy->speed_cap_mask & PORT_HW_CFG_SPEED_CAPABILITY_D0_1G)
control2 |= MDIO_SERDES_DIGITAL_A_1000X_CONTROL2_PRL_DT_EN;
else
DP(NETIF_MSG_LINK, "phy->speed_cap_mask = 0x%x, control2 = 0x%x\n",
phy->speed_cap_mask, control2);
CL45_WR_OVER_CL22(bp, phy,
- MDIO_REG_BANK_SERDES_DIGITAL,
- MDIO_SERDES_DIGITAL_A_1000X_CONTROL2,
- control2);
+ MDIO_REG_BANK_SERDES_DIGITAL,
+ MDIO_SERDES_DIGITAL_A_1000X_CONTROL2,
+ control2);
if ((phy->type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_DIRECT) &&
(phy->speed_cap_mask &
DP(NETIF_MSG_LINK, "XGXS\n");
CL45_WR_OVER_CL22(bp, phy,
- MDIO_REG_BANK_10G_PARALLEL_DETECT,
- MDIO_10G_PARALLEL_DETECT_PAR_DET_10G_LINK,
- MDIO_10G_PARALLEL_DETECT_PAR_DET_10G_LINK_CNT);
+ MDIO_REG_BANK_10G_PARALLEL_DETECT,
+ MDIO_10G_PARALLEL_DETECT_PAR_DET_10G_LINK,
+ MDIO_10G_PARALLEL_DETECT_PAR_DET_10G_LINK_CNT);
CL45_RD_OVER_CL22(bp, phy,
- MDIO_REG_BANK_10G_PARALLEL_DETECT,
- MDIO_10G_PARALLEL_DETECT_PAR_DET_10G_CONTROL,
- &control2);
+ MDIO_REG_BANK_10G_PARALLEL_DETECT,
+ MDIO_10G_PARALLEL_DETECT_PAR_DET_10G_CONTROL,
+ &control2);
control2 |=
MDIO_10G_PARALLEL_DETECT_PAR_DET_10G_CONTROL_PARDET10G_EN;
CL45_WR_OVER_CL22(bp, phy,
- MDIO_REG_BANK_10G_PARALLEL_DETECT,
- MDIO_10G_PARALLEL_DETECT_PAR_DET_10G_CONTROL,
- control2);
+ MDIO_REG_BANK_10G_PARALLEL_DETECT,
+ MDIO_10G_PARALLEL_DETECT_PAR_DET_10G_CONTROL,
+ control2);
/* Disable parallel detection of HiG */
CL45_WR_OVER_CL22(bp, phy,
- MDIO_REG_BANK_XGXS_BLOCK2,
- MDIO_XGXS_BLOCK2_UNICORE_MODE_10G,
- MDIO_XGXS_BLOCK2_UNICORE_MODE_10G_CX4_XGXS |
- MDIO_XGXS_BLOCK2_UNICORE_MODE_10G_HIGIG_XGXS);
+ MDIO_REG_BANK_XGXS_BLOCK2,
+ MDIO_XGXS_BLOCK2_UNICORE_MODE_10G,
+ MDIO_XGXS_BLOCK2_UNICORE_MODE_10G_CX4_XGXS |
+ MDIO_XGXS_BLOCK2_UNICORE_MODE_10G_HIGIG_XGXS);
}
}
static void bnx2x_set_autoneg(struct bnx2x_phy *phy,
struct link_params *params,
- struct link_vars *vars,
- u8 enable_cl73)
+ struct link_vars *vars,
+ u8 enable_cl73)
{
struct bnx2x *bp = params->bp;
u16 reg_val;
/* CL37 Autoneg */
CL45_RD_OVER_CL22(bp, phy,
- MDIO_REG_BANK_COMBO_IEEE0,
- MDIO_COMBO_IEEE0_MII_CONTROL, ®_val);
+ MDIO_REG_BANK_COMBO_IEEE0,
+ MDIO_COMBO_IEEE0_MII_CONTROL, ®_val);
/* CL37 Autoneg Enabled */
if (vars->line_speed == SPEED_AUTO_NEG)
MDIO_COMBO_IEEO_MII_CONTROL_RESTART_AN);
CL45_WR_OVER_CL22(bp, phy,
- MDIO_REG_BANK_COMBO_IEEE0,
- MDIO_COMBO_IEEE0_MII_CONTROL, reg_val);
+ MDIO_REG_BANK_COMBO_IEEE0,
+ MDIO_COMBO_IEEE0_MII_CONTROL, reg_val);
/* Enable/Disable Autodetection */
CL45_RD_OVER_CL22(bp, phy,
- MDIO_REG_BANK_SERDES_DIGITAL,
- MDIO_SERDES_DIGITAL_A_1000X_CONTROL1, ®_val);
+ MDIO_REG_BANK_SERDES_DIGITAL,
+ MDIO_SERDES_DIGITAL_A_1000X_CONTROL1, ®_val);
reg_val &= ~(MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_SIGNAL_DETECT_EN |
MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_INVERT_SIGNAL_DETECT);
reg_val |= MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_FIBER_MODE;
reg_val &= ~MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_AUTODET;
CL45_WR_OVER_CL22(bp, phy,
- MDIO_REG_BANK_SERDES_DIGITAL,
- MDIO_SERDES_DIGITAL_A_1000X_CONTROL1, reg_val);
+ MDIO_REG_BANK_SERDES_DIGITAL,
+ MDIO_SERDES_DIGITAL_A_1000X_CONTROL1, reg_val);
/* Enable TetonII and BAM autoneg */
CL45_RD_OVER_CL22(bp, phy,
- MDIO_REG_BANK_BAM_NEXT_PAGE,
- MDIO_BAM_NEXT_PAGE_MP5_NEXT_PAGE_CTRL,
+ MDIO_REG_BANK_BAM_NEXT_PAGE,
+ MDIO_BAM_NEXT_PAGE_MP5_NEXT_PAGE_CTRL,
®_val);
if (vars->line_speed == SPEED_AUTO_NEG) {
/* Enable BAM aneg Mode and TetonII aneg Mode */
MDIO_BAM_NEXT_PAGE_MP5_NEXT_PAGE_CTRL_TETON_AN);
}
CL45_WR_OVER_CL22(bp, phy,
- MDIO_REG_BANK_BAM_NEXT_PAGE,
- MDIO_BAM_NEXT_PAGE_MP5_NEXT_PAGE_CTRL,
- reg_val);
+ MDIO_REG_BANK_BAM_NEXT_PAGE,
+ MDIO_BAM_NEXT_PAGE_MP5_NEXT_PAGE_CTRL,
+ reg_val);
if (enable_cl73) {
/* Enable Cl73 FSM status bits */
CL45_WR_OVER_CL22(bp, phy,
- MDIO_REG_BANK_CL73_USERB0,
- MDIO_CL73_USERB0_CL73_UCTRL,
- 0xe);
+ MDIO_REG_BANK_CL73_USERB0,
+ MDIO_CL73_USERB0_CL73_UCTRL,
+ 0xe);
/* Enable BAM Station Manager*/
CL45_WR_OVER_CL22(bp, phy,
/* Advertise CL73 link speeds */
CL45_RD_OVER_CL22(bp, phy,
- MDIO_REG_BANK_CL73_IEEEB1,
- MDIO_CL73_IEEEB1_AN_ADV2,
- ®_val);
+ MDIO_REG_BANK_CL73_IEEEB1,
+ MDIO_CL73_IEEEB1_AN_ADV2,
+ ®_val);
if (phy->speed_cap_mask &
PORT_HW_CFG_SPEED_CAPABILITY_D0_10G)
reg_val |= MDIO_CL73_IEEEB1_AN_ADV2_ADVR_10G_KX4;
reg_val |= MDIO_CL73_IEEEB1_AN_ADV2_ADVR_1000M_KX;
CL45_WR_OVER_CL22(bp, phy,
- MDIO_REG_BANK_CL73_IEEEB1,
- MDIO_CL73_IEEEB1_AN_ADV2,
- reg_val);
+ MDIO_REG_BANK_CL73_IEEEB1,
+ MDIO_CL73_IEEEB1_AN_ADV2,
+ reg_val);
/* CL73 Autoneg Enabled */
reg_val = MDIO_CL73_IEEEB0_CL73_AN_CONTROL_AN_EN;
reg_val = 0;
CL45_WR_OVER_CL22(bp, phy,
- MDIO_REG_BANK_CL73_IEEEB0,
- MDIO_CL73_IEEEB0_CL73_AN_CONTROL, reg_val);
+ MDIO_REG_BANK_CL73_IEEEB0,
+ MDIO_CL73_IEEEB0_CL73_AN_CONTROL, reg_val);
}
/* program SerDes, forced speed */
static void bnx2x_program_serdes(struct bnx2x_phy *phy,
struct link_params *params,
- struct link_vars *vars)
+ struct link_vars *vars)
{
struct bnx2x *bp = params->bp;
u16 reg_val;
/* program duplex, disable autoneg and sgmii*/
CL45_RD_OVER_CL22(bp, phy,
- MDIO_REG_BANK_COMBO_IEEE0,
- MDIO_COMBO_IEEE0_MII_CONTROL, ®_val);
+ MDIO_REG_BANK_COMBO_IEEE0,
+ MDIO_COMBO_IEEE0_MII_CONTROL, ®_val);
reg_val &= ~(MDIO_COMBO_IEEO_MII_CONTROL_FULL_DUPLEX |
MDIO_COMBO_IEEO_MII_CONTROL_AN_EN |
MDIO_COMBO_IEEO_MII_CONTROL_MAN_SGMII_SP_MASK);
if (phy->req_duplex == DUPLEX_FULL)
reg_val |= MDIO_COMBO_IEEO_MII_CONTROL_FULL_DUPLEX;
CL45_WR_OVER_CL22(bp, phy,
- MDIO_REG_BANK_COMBO_IEEE0,
- MDIO_COMBO_IEEE0_MII_CONTROL, reg_val);
+ MDIO_REG_BANK_COMBO_IEEE0,
+ MDIO_COMBO_IEEE0_MII_CONTROL, reg_val);
/* program speed
- needed only if the speed is greater than 1G (2.5G or 10G) */
CL45_RD_OVER_CL22(bp, phy,
- MDIO_REG_BANK_SERDES_DIGITAL,
- MDIO_SERDES_DIGITAL_MISC1, ®_val);
+ MDIO_REG_BANK_SERDES_DIGITAL,
+ MDIO_SERDES_DIGITAL_MISC1, ®_val);
/* clearing the speed value before setting the right speed */
DP(NETIF_MSG_LINK, "MDIO_REG_BANK_SERDES_DIGITAL = 0x%x\n", reg_val);
}
CL45_WR_OVER_CL22(bp, phy,
- MDIO_REG_BANK_SERDES_DIGITAL,
- MDIO_SERDES_DIGITAL_MISC1, reg_val);
+ MDIO_REG_BANK_SERDES_DIGITAL,
+ MDIO_SERDES_DIGITAL_MISC1, reg_val);
}
if (phy->speed_cap_mask & PORT_HW_CFG_SPEED_CAPABILITY_D0_10G)
val |= MDIO_OVER_1G_UP1_10G;
CL45_WR_OVER_CL22(bp, phy,
- MDIO_REG_BANK_OVER_1G,
- MDIO_OVER_1G_UP1, val);
+ MDIO_REG_BANK_OVER_1G,
+ MDIO_OVER_1G_UP1, val);
CL45_WR_OVER_CL22(bp, phy,
- MDIO_REG_BANK_OVER_1G,
- MDIO_OVER_1G_UP3, 0x400);
+ MDIO_REG_BANK_OVER_1G,
+ MDIO_OVER_1G_UP3, 0x400);
}
static void bnx2x_calc_ieee_aneg_adv(struct bnx2x_phy *phy,
switch (phy->req_flow_ctrl) {
case BNX2X_FLOW_CTRL_AUTO:
- if (params->req_fc_auto_adv == BNX2X_FLOW_CTRL_BOTH) {
- *ieee_fc |=
- MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH;
- } else {
+ if (params->req_fc_auto_adv == BNX2X_FLOW_CTRL_BOTH)
+ *ieee_fc |= MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH;
+ else
*ieee_fc |=
- MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_ASYMMETRIC;
- }
+ MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_ASYMMETRIC;
break;
case BNX2X_FLOW_CTRL_TX:
- *ieee_fc |=
- MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_ASYMMETRIC;
+ *ieee_fc |= MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_ASYMMETRIC;
break;
case BNX2X_FLOW_CTRL_RX:
static void bnx2x_set_ieee_aneg_advertisment(struct bnx2x_phy *phy,
struct link_params *params,
- u16 ieee_fc)
+ u16 ieee_fc)
{
struct bnx2x *bp = params->bp;
u16 val;
/* for AN, we are always publishing full duplex */
CL45_WR_OVER_CL22(bp, phy,
- MDIO_REG_BANK_COMBO_IEEE0,
- MDIO_COMBO_IEEE0_AUTO_NEG_ADV, ieee_fc);
+ MDIO_REG_BANK_COMBO_IEEE0,
+ MDIO_COMBO_IEEE0_AUTO_NEG_ADV, ieee_fc);
CL45_RD_OVER_CL22(bp, phy,
- MDIO_REG_BANK_CL73_IEEEB1,
- MDIO_CL73_IEEEB1_AN_ADV1, &val);
+ MDIO_REG_BANK_CL73_IEEEB1,
+ MDIO_CL73_IEEEB1_AN_ADV1, &val);
val &= ~MDIO_CL73_IEEEB1_AN_ADV1_PAUSE_BOTH;
val |= ((ieee_fc<<3) & MDIO_CL73_IEEEB1_AN_ADV1_PAUSE_MASK);
CL45_WR_OVER_CL22(bp, phy,
- MDIO_REG_BANK_CL73_IEEEB1,
- MDIO_CL73_IEEEB1_AN_ADV1, val);
+ MDIO_REG_BANK_CL73_IEEEB1,
+ MDIO_CL73_IEEEB1_AN_ADV1, val);
}
static void bnx2x_restart_autoneg(struct bnx2x_phy *phy,
if (enable_cl73) {
CL45_RD_OVER_CL22(bp, phy,
- MDIO_REG_BANK_CL73_IEEEB0,
- MDIO_CL73_IEEEB0_CL73_AN_CONTROL,
- &mii_control);
+ MDIO_REG_BANK_CL73_IEEEB0,
+ MDIO_CL73_IEEEB0_CL73_AN_CONTROL,
+ &mii_control);
CL45_WR_OVER_CL22(bp, phy,
- MDIO_REG_BANK_CL73_IEEEB0,
- MDIO_CL73_IEEEB0_CL73_AN_CONTROL,
- (mii_control |
- MDIO_CL73_IEEEB0_CL73_AN_CONTROL_AN_EN |
- MDIO_CL73_IEEEB0_CL73_AN_CONTROL_RESTART_AN));
+ MDIO_REG_BANK_CL73_IEEEB0,
+ MDIO_CL73_IEEEB0_CL73_AN_CONTROL,
+ (mii_control |
+ MDIO_CL73_IEEEB0_CL73_AN_CONTROL_AN_EN |
+ MDIO_CL73_IEEEB0_CL73_AN_CONTROL_RESTART_AN));
} else {
CL45_RD_OVER_CL22(bp, phy,
- MDIO_REG_BANK_COMBO_IEEE0,
- MDIO_COMBO_IEEE0_MII_CONTROL,
- &mii_control);
+ MDIO_REG_BANK_COMBO_IEEE0,
+ MDIO_COMBO_IEEE0_MII_CONTROL,
+ &mii_control);
DP(NETIF_MSG_LINK,
"bnx2x_restart_autoneg mii_control before = 0x%x\n",
mii_control);
CL45_WR_OVER_CL22(bp, phy,
- MDIO_REG_BANK_COMBO_IEEE0,
- MDIO_COMBO_IEEE0_MII_CONTROL,
- (mii_control |
- MDIO_COMBO_IEEO_MII_CONTROL_AN_EN |
- MDIO_COMBO_IEEO_MII_CONTROL_RESTART_AN));
+ MDIO_REG_BANK_COMBO_IEEE0,
+ MDIO_COMBO_IEEE0_MII_CONTROL,
+ (mii_control |
+ MDIO_COMBO_IEEO_MII_CONTROL_AN_EN |
+ MDIO_COMBO_IEEO_MII_CONTROL_RESTART_AN));
}
}
static void bnx2x_initialize_sgmii_process(struct bnx2x_phy *phy,
struct link_params *params,
- struct link_vars *vars)
+ struct link_vars *vars)
{
struct bnx2x *bp = params->bp;
u16 control1;
/* in SGMII mode, the unicore is always slave */
CL45_RD_OVER_CL22(bp, phy,
- MDIO_REG_BANK_SERDES_DIGITAL,
- MDIO_SERDES_DIGITAL_A_1000X_CONTROL1,
- &control1);
+ MDIO_REG_BANK_SERDES_DIGITAL,
+ MDIO_SERDES_DIGITAL_A_1000X_CONTROL1,
+ &control1);
control1 |= MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_INVERT_SIGNAL_DETECT;
/* set sgmii mode (and not fiber) */
control1 &= ~(MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_FIBER_MODE |
MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_AUTODET |
MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_MSTR_MODE);
CL45_WR_OVER_CL22(bp, phy,
- MDIO_REG_BANK_SERDES_DIGITAL,
- MDIO_SERDES_DIGITAL_A_1000X_CONTROL1,
- control1);
+ MDIO_REG_BANK_SERDES_DIGITAL,
+ MDIO_SERDES_DIGITAL_A_1000X_CONTROL1,
+ control1);
/* if forced speed */
if (!(vars->line_speed == SPEED_AUTO_NEG)) {
u16 mii_control;
CL45_RD_OVER_CL22(bp, phy,
- MDIO_REG_BANK_COMBO_IEEE0,
- MDIO_COMBO_IEEE0_MII_CONTROL,
- &mii_control);
+ MDIO_REG_BANK_COMBO_IEEE0,
+ MDIO_COMBO_IEEE0_MII_CONTROL,
+ &mii_control);
mii_control &= ~(MDIO_COMBO_IEEO_MII_CONTROL_AN_EN |
MDIO_COMBO_IEEO_MII_CONTROL_MAN_SGMII_SP_MASK|
MDIO_COMBO_IEEO_MII_CONTROL_FULL_DUPLEX);
mii_control |=
MDIO_COMBO_IEEO_MII_CONTROL_FULL_DUPLEX;
CL45_WR_OVER_CL22(bp, phy,
- MDIO_REG_BANK_COMBO_IEEE0,
- MDIO_COMBO_IEEE0_MII_CONTROL,
- mii_control);
+ MDIO_REG_BANK_COMBO_IEEE0,
+ MDIO_COMBO_IEEE0_MII_CONTROL,
+ mii_control);
} else { /* AN mode */
/* enable and restart AN */
static void bnx2x_pause_resolve(struct link_vars *vars, u32 pause_result)
{ /* LD LP */
- switch (pause_result) { /* ASYM P ASYM P */
- case 0xb: /* 1 0 1 1 */
+ switch (pause_result) { /* ASYM P ASYM P */
+ case 0xb: /* 1 0 1 1 */
vars->flow_ctrl = BNX2X_FLOW_CTRL_TX;
break;
- case 0xe: /* 1 1 1 0 */
+ case 0xe: /* 1 1 1 0 */
vars->flow_ctrl = BNX2X_FLOW_CTRL_RX;
break;
- case 0x5: /* 0 1 0 1 */
- case 0x7: /* 0 1 1 1 */
- case 0xd: /* 1 1 0 1 */
- case 0xf: /* 1 1 1 1 */
+ case 0x5: /* 0 1 0 1 */
+ case 0x7: /* 0 1 1 1 */
+ case 0xd: /* 1 1 0 1 */
+ case 0xf: /* 1 1 1 1 */
vars->flow_ctrl = BNX2X_FLOW_CTRL_BOTH;
break;
if (phy->req_line_speed != SPEED_AUTO_NEG)
return 0;
CL45_RD_OVER_CL22(bp, phy,
- MDIO_REG_BANK_SERDES_DIGITAL,
- MDIO_SERDES_DIGITAL_A_1000X_STATUS2,
- &status2_1000x);
+ MDIO_REG_BANK_SERDES_DIGITAL,
+ MDIO_SERDES_DIGITAL_A_1000X_STATUS2,
+ &status2_1000x);
CL45_RD_OVER_CL22(bp, phy,
- MDIO_REG_BANK_SERDES_DIGITAL,
- MDIO_SERDES_DIGITAL_A_1000X_STATUS2,
- &status2_1000x);
+ MDIO_REG_BANK_SERDES_DIGITAL,
+ MDIO_SERDES_DIGITAL_A_1000X_STATUS2,
+ &status2_1000x);
if (status2_1000x & MDIO_SERDES_DIGITAL_A_1000X_STATUS2_AN_DISABLED) {
DP(NETIF_MSG_LINK, "1G parallel detect link on port %d\n",
params->port);
}
CL45_RD_OVER_CL22(bp, phy,
- MDIO_REG_BANK_10G_PARALLEL_DETECT,
- MDIO_10G_PARALLEL_DETECT_PAR_DET_10G_STATUS,
- &pd_10g);
+ MDIO_REG_BANK_10G_PARALLEL_DETECT,
+ MDIO_10G_PARALLEL_DETECT_PAR_DET_10G_STATUS,
+ &pd_10g);
if (pd_10g & MDIO_10G_PARALLEL_DETECT_PAR_DET_10G_STATUS_PD_LINK) {
DP(NETIF_MSG_LINK, "10G parallel detect link on port %d\n",
MDIO_GP_STATUS_TOP_AN_STATUS1_CL73_MR_LP_NP_AN_ABLE)) {
CL45_RD_OVER_CL22(bp, phy,
- MDIO_REG_BANK_CL73_IEEEB1,
- MDIO_CL73_IEEEB1_AN_ADV1,
- &ld_pause);
+ MDIO_REG_BANK_CL73_IEEEB1,
+ MDIO_CL73_IEEEB1_AN_ADV1,
+ &ld_pause);
CL45_RD_OVER_CL22(bp, phy,
- MDIO_REG_BANK_CL73_IEEEB1,
- MDIO_CL73_IEEEB1_AN_LP_ADV1,
- &lp_pause);
+ MDIO_REG_BANK_CL73_IEEEB1,
+ MDIO_CL73_IEEEB1_AN_LP_ADV1,
+ &lp_pause);
pause_result = (ld_pause &
MDIO_CL73_IEEEB1_AN_ADV1_PAUSE_MASK)
>> 8;
pause_result);
} else {
CL45_RD_OVER_CL22(bp, phy,
- MDIO_REG_BANK_COMBO_IEEE0,
- MDIO_COMBO_IEEE0_AUTO_NEG_ADV,
- &ld_pause);
+ MDIO_REG_BANK_COMBO_IEEE0,
+ MDIO_COMBO_IEEE0_AUTO_NEG_ADV,
+ &ld_pause);
CL45_RD_OVER_CL22(bp, phy,
- MDIO_REG_BANK_COMBO_IEEE0,
- MDIO_COMBO_IEEE0_AUTO_NEG_LINK_PARTNER_ABILITY1,
- &lp_pause);
+ MDIO_REG_BANK_COMBO_IEEE0,
+ MDIO_COMBO_IEEE0_AUTO_NEG_LINK_PARTNER_ABILITY1,
+ &lp_pause);
pause_result = (ld_pause &
MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_MASK)>>5;
pause_result |= (lp_pause &
- MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_MASK)>>7;
+ MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_MASK)>>7;
DP(NETIF_MSG_LINK, "pause_result CL37 0x%x\n",
pause_result);
}
DP(NETIF_MSG_LINK, "bnx2x_check_fallback_to_cl37\n");
/* Step 1: Make sure signal is detected */
CL45_RD_OVER_CL22(bp, phy,
- MDIO_REG_BANK_RX0,
- MDIO_RX0_RX_STATUS,
- &rx_status);
+ MDIO_REG_BANK_RX0,
+ MDIO_RX0_RX_STATUS,
+ &rx_status);
if ((rx_status & MDIO_RX0_RX_STATUS_SIGDET) !=
(MDIO_RX0_RX_STATUS_SIGDET)) {
DP(NETIF_MSG_LINK, "Signal is not detected. Restoring CL73."
"rx_status(0x80b0) = 0x%x\n", rx_status);
CL45_WR_OVER_CL22(bp, phy,
- MDIO_REG_BANK_CL73_IEEEB0,
- MDIO_CL73_IEEEB0_CL73_AN_CONTROL,
- MDIO_CL73_IEEEB0_CL73_AN_CONTROL_AN_EN);
+ MDIO_REG_BANK_CL73_IEEEB0,
+ MDIO_CL73_IEEEB0_CL73_AN_CONTROL,
+ MDIO_CL73_IEEEB0_CL73_AN_CONTROL_AN_EN);
return;
}
/* Step 2: Check CL73 state machine */
CL45_RD_OVER_CL22(bp, phy,
- MDIO_REG_BANK_CL73_USERB0,
- MDIO_CL73_USERB0_CL73_USTAT1,
- &ustat_val);
+ MDIO_REG_BANK_CL73_USERB0,
+ MDIO_CL73_USERB0_CL73_USTAT1,
+ &ustat_val);
if ((ustat_val &
(MDIO_CL73_USERB0_CL73_USTAT1_LINK_STATUS_CHECK |
MDIO_CL73_USERB0_CL73_USTAT1_AN_GOOD_CHECK_BAM37)) !=
/* Step 3: Check CL37 Message Pages received to indicate LP
supports only CL37 */
CL45_RD_OVER_CL22(bp, phy,
- MDIO_REG_BANK_REMOTE_PHY,
- MDIO_REMOTE_PHY_MISC_RX_STATUS,
- &cl37_fsm_recieved);
+ MDIO_REG_BANK_REMOTE_PHY,
+ MDIO_REMOTE_PHY_MISC_RX_STATUS,
+ &cl37_fsm_recieved);
if ((cl37_fsm_recieved &
(MDIO_REMOTE_PHY_MISC_RX_STATUS_CL37_FSM_RECEIVED_OVER1G_MSG |
MDIO_REMOTE_PHY_MISC_RX_STATUS_CL37_FSM_RECEIVED_BRCM_OUI_MSG)) !=
cl37 BAM. In this case we disable cl73 and restart cl37 auto-neg */
/* Disable CL73 */
CL45_WR_OVER_CL22(bp, phy,
- MDIO_REG_BANK_CL73_IEEEB0,
- MDIO_CL73_IEEEB0_CL73_AN_CONTROL,
- 0);
+ MDIO_REG_BANK_CL73_IEEEB0,
+ MDIO_CL73_IEEEB0_CL73_AN_CONTROL,
+ 0);
/* Restart CL37 autoneg */
bnx2x_restart_autoneg(phy, params, 0);
DP(NETIF_MSG_LINK, "Disabling CL73, and restarting CL37 autoneg\n");
struct link_vars *vars)
{
struct bnx2x *bp = params->bp;
- u16 new_line_speed , gp_status;
+ u16 new_line_speed, gp_status;
u8 rc = 0;
/* Read gp_status */
CL45_RD_OVER_CL22(bp, phy,
- MDIO_REG_BANK_GP_STATUS,
- MDIO_GP_STATUS_TOP_AN_STATUS1,
- &gp_status);
+ MDIO_REG_BANK_GP_STATUS,
+ MDIO_GP_STATUS_TOP_AN_STATUS1,
+ &gp_status);
if (phy->req_line_speed == SPEED_AUTO_NEG)
vars->link_status |= LINK_STATUS_AUTO_NEGOTIATE_ENABLED;
/* read precomp */
CL45_RD_OVER_CL22(bp, phy,
- MDIO_REG_BANK_OVER_1G,
- MDIO_OVER_1G_LP_UP2, &lp_up2);
+ MDIO_REG_BANK_OVER_1G,
+ MDIO_OVER_1G_LP_UP2, &lp_up2);
/* bits [10:7] at lp_up2, positioned at [15:12] */
lp_up2 = (((lp_up2 & MDIO_OVER_1G_LP_UP2_PREEMPHASIS_MASK) >>
for (bank = MDIO_REG_BANK_TX0; bank <= MDIO_REG_BANK_TX3;
bank += (MDIO_REG_BANK_TX1 - MDIO_REG_BANK_TX0)) {
CL45_RD_OVER_CL22(bp, phy,
- bank,
- MDIO_TX0_TX_DRIVER, &tx_driver);
+ bank,
+ MDIO_TX0_TX_DRIVER, &tx_driver);
/* replace tx_driver bits [15:12] */
if (lp_up2 !=
tx_driver &= ~MDIO_TX0_TX_DRIVER_PREEMPHASIS_MASK;
tx_driver |= lp_up2;
CL45_WR_OVER_CL22(bp, phy,
- bank,
- MDIO_TX0_TX_DRIVER, tx_driver);
+ bank,
+ MDIO_TX0_TX_DRIVER, tx_driver);
}
}
}
DP(NETIF_MSG_LINK, "setting link speed & duplex\n");
bnx2x_bits_dis(bp, GRCBASE_EMAC0 + port*0x400 +
- EMAC_REG_EMAC_MODE,
- (EMAC_MODE_25G_MODE |
- EMAC_MODE_PORT_MII_10M |
- EMAC_MODE_HALF_DUPLEX));
+ EMAC_REG_EMAC_MODE,
+ (EMAC_MODE_25G_MODE |
+ EMAC_MODE_PORT_MII_10M |
+ EMAC_MODE_HALF_DUPLEX));
switch (vars->line_speed) {
case SPEED_10:
mode |= EMAC_MODE_PORT_MII_10M;
if (vars->duplex == DUPLEX_HALF)
mode |= EMAC_MODE_HALF_DUPLEX;
bnx2x_bits_en(bp,
- GRCBASE_EMAC0 + port*0x400 + EMAC_REG_EMAC_MODE,
- mode);
+ GRCBASE_EMAC0 + port*0x400 + EMAC_REG_EMAC_MODE,
+ mode);
bnx2x_set_led(params, vars, LED_MODE_OPER, vars->line_speed);
return 0;
/* forced speed requested? */
if (vars->line_speed != SPEED_AUTO_NEG ||
(SINGLE_MEDIA_DIRECT(params) &&
- params->loopback_mode == LOOPBACK_EXT)) {
+ params->loopback_mode == LOOPBACK_EXT)) {
DP(NETIF_MSG_LINK, "not SGMII, no AN\n");
/* disable autoneg */
/* program duplex & pause advertisement (for aneg) */
bnx2x_set_ieee_aneg_advertisment(phy, params,
- vars->ieee_fc);
+ vars->ieee_fc);
/* enable autoneg */
bnx2x_set_autoneg(phy, params, vars, enable_cl73);
/* For all latched-signal=up : Re-Arm Latch signals */
REG_WR(bp, NIG_REG_LATCH_STATUS_0 + port*8,
- (latch_status & 0xfffe) | (latch_status & 1));
+ (latch_status & 0xfffe) | (latch_status & 1));
}
/* For all latched-signal=up,Write original_signal to status */
}
static void bnx2x_link_int_ack(struct link_params *params,
- struct link_vars *vars, u8 is_10g)
+ struct link_vars *vars, u8 is_10g)
{
struct bnx2x *bp = params->bp;
u8 port = params->port;
/* first reset all status
* we assume only one line will be change at a time */
bnx2x_bits_dis(bp, NIG_REG_STATUS_INTERRUPT_PORT0 + port*4,
- (NIG_STATUS_XGXS0_LINK10G |
- NIG_STATUS_XGXS0_LINK_STATUS |
- NIG_STATUS_SERDES0_LINK_STATUS));
+ (NIG_STATUS_XGXS0_LINK10G |
+ NIG_STATUS_XGXS0_LINK_STATUS |
+ NIG_STATUS_SERDES0_LINK_STATUS));
if (vars->phy_link_up) {
if (is_10g) {
/* Disable the 10G link interrupt
}
if ((params->num_phys == MAX_PHYS) &&
(params->phy[EXT_PHY2].ver_addr != 0)) {
- spirom_ver = REG_RD(bp,
- params->phy[EXT_PHY2].ver_addr);
+ spirom_ver = REG_RD(bp, params->phy[EXT_PHY2].ver_addr);
if (params->phy[EXT_PHY2].format_fw_ver) {
*ver_p = '/';
ver_p++;
/* change the uni_phy_addr in the nig */
md_devad = REG_RD(bp, (NIG_REG_XGXS0_CTRL_MD_DEVAD +
- port*0x18));
+ port*0x18));
REG_WR(bp, NIG_REG_XGXS0_CTRL_MD_DEVAD + port*0x18, 0x5);
bnx2x_cl45_write(bp, phy,
- 5,
- (MDIO_REG_BANK_AER_BLOCK +
- (MDIO_AER_BLOCK_AER_REG & 0xf)),
- 0x2800);
+ 5,
+ (MDIO_REG_BANK_AER_BLOCK +
+ (MDIO_AER_BLOCK_AER_REG & 0xf)),
+ 0x2800);
bnx2x_cl45_write(bp, phy,
- 5,
- (MDIO_REG_BANK_CL73_IEEEB0 +
- (MDIO_CL73_IEEEB0_CL73_AN_CONTROL & 0xf)),
- 0x6041);
+ 5,
+ (MDIO_REG_BANK_CL73_IEEEB0 +
+ (MDIO_CL73_IEEEB0_CL73_AN_CONTROL & 0xf)),
+ 0x6041);
msleep(200);
/* set aer mmd back */
bnx2x_set_aer_mmd_xgxs(params, phy);
/* and md_devad */
- REG_WR(bp, NIG_REG_XGXS0_CTRL_MD_DEVAD + port*0x18,
- md_devad);
-
+ REG_WR(bp, NIG_REG_XGXS0_CTRL_MD_DEVAD + port*0x18, md_devad);
} else {
u16 mii_ctrl;
DP(NETIF_MSG_LINK, "XGXS 1G loopback enable\n");
case LED_MODE_OFF:
REG_WR(bp, NIG_REG_LED_10G_P0 + port*4, 0);
REG_WR(bp, NIG_REG_LED_MODE_P0 + port*4,
- SHARED_HW_CFG_LED_MAC1);
+ SHARED_HW_CFG_LED_MAC1);
tmp = EMAC_RD(bp, EMAC_REG_EMAC_LED);
EMAC_WR(bp, EMAC_REG_EMAC_LED, (tmp | EMAC_LED_OVERRIDE));
REG_WR(bp, NIG_REG_LED_MODE_P0 + port*4, 0);
REG_WR(bp, NIG_REG_LED_10G_P0 + port*4, 1);
} else {
- REG_WR(bp, NIG_REG_LED_MODE_P0 + port*4,
- hw_led_mode);
+ REG_WR(bp, NIG_REG_LED_MODE_P0 + port*4, hw_led_mode);
}
- REG_WR(bp, NIG_REG_LED_CONTROL_OVERRIDE_TRAFFIC_P0 +
- port*4, 0);
+ REG_WR(bp, NIG_REG_LED_CONTROL_OVERRIDE_TRAFFIC_P0 + port*4, 0);
/* Set blinking rate to ~15.9Hz */
REG_WR(bp, NIG_REG_LED_CONTROL_BLINK_RATE_P0 + port*4,
- LED_BLINK_RATE_VAL);
+ LED_BLINK_RATE_VAL);
REG_WR(bp, NIG_REG_LED_CONTROL_BLINK_RATE_ENA_P0 +
- port*4, 1);
+ port*4, 1);
tmp = EMAC_RD(bp, EMAC_REG_EMAC_LED);
- EMAC_WR(bp, EMAC_REG_EMAC_LED,
- (tmp & (~EMAC_LED_OVERRIDE)));
+ EMAC_WR(bp, EMAC_REG_EMAC_LED, (tmp & (~EMAC_LED_OVERRIDE)));
if (CHIP_IS_E1(bp) &&
((speed == SPEED_2500) ||
/* On Everest 1 Ax chip versions for speeds less than
10G LED scheme is different */
REG_WR(bp, NIG_REG_LED_CONTROL_OVERRIDE_TRAFFIC_P0
- + port*4, 1);
+ + port*4, 1);
REG_WR(bp, NIG_REG_LED_CONTROL_TRAFFIC_P0 +
- port*4, 0);
+ port*4, 0);
REG_WR(bp, NIG_REG_LED_CONTROL_BLINK_TRAFFIC_P0 +
- port*4, 1);
+ port*4, 1);
}
break;
struct link_vars temp_vars;
CL45_RD_OVER_CL22(bp, ¶ms->phy[INT_PHY],
- MDIO_REG_BANK_GP_STATUS,
- MDIO_GP_STATUS_TOP_AN_STATUS1,
- &gp_status);
+ MDIO_REG_BANK_GP_STATUS,
+ MDIO_GP_STATUS_TOP_AN_STATUS1,
+ &gp_status);
/* link is up only if both local phy and external phy are up */
if (!(gp_status & MDIO_GP_STATUS_TOP_AN_STATUS1_LINK_STATUS))
return -ESRCH;
struct link_params *params)
{
/* reset the SerDes/XGXS */
- REG_WR(params->bp, GRCBASE_MISC +
- MISC_REGISTERS_RESET_REG_3_CLEAR,
- (0x1ff << (params->port*16)));
+ REG_WR(params->bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_3_CLEAR,
+ (0x1ff << (params->port*16)));
}
static void bnx2x_common_ext_link_reset(struct bnx2x_phy *phy,
else
gpio_port = params->port;
bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_1,
- MISC_REGISTERS_GPIO_OUTPUT_LOW,
- gpio_port);
+ MISC_REGISTERS_GPIO_OUTPUT_LOW,
+ gpio_port);
bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2,
- MISC_REGISTERS_GPIO_OUTPUT_LOW,
- gpio_port);
+ MISC_REGISTERS_GPIO_OUTPUT_LOW,
+ gpio_port);
DP(NETIF_MSG_LINK, "reset external PHY\n");
}
/* reset BigMac */
bnx2x_bmac_rx_disable(bp, params->port);
- REG_WR(bp, GRCBASE_MISC +
- MISC_REGISTERS_RESET_REG_2_CLEAR,
- (MISC_REGISTERS_RESET_REG_2_RST_BMAC0 << port));
+ REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_2_CLEAR,
+ (MISC_REGISTERS_RESET_REG_2_RST_BMAC0 << port));
return 0;
}
REG_RD(bp, NIG_REG_STATUS_INTERRUPT_PORT0 + port*4));
is_mi_int = (u8)(REG_RD(bp, NIG_REG_EMAC0_STATUS_MISC_MI_INT +
- port*0x18) > 0);
+ port*0x18) > 0);
DP(NETIF_MSG_LINK, "int_mask 0x%x MI_INT %x, SERDES_LINK %x\n",
REG_RD(bp, NIG_REG_MASK_INTERRUPT_PORT0 + port*4),
is_mi_int,
- REG_RD(bp,
- NIG_REG_SERDES0_STATUS_LINK_STATUS + port*0x3c));
+ REG_RD(bp, NIG_REG_SERDES0_STATUS_LINK_STATUS + port*0x3c));
DP(NETIF_MSG_LINK, " 10G %x, XGXS_LINK %x\n",
REG_RD(bp, NIG_REG_XGXS0_STATUS_LINK10G + port*0x68),
ext_phy_line_speed);
vars->phy_link_up = 0;
} else if (prev_line_speed != vars->line_speed) {
- REG_WR(bp, NIG_REG_EGRESS_DRAIN0_MODE
- + params->port*4, 0);
+ REG_WR(bp, NIG_REG_EGRESS_DRAIN0_MODE + params->port*4,
+ 0);
msleep(1);
}
}
void bnx2x_ext_phy_hw_reset(struct bnx2x *bp, u8 port)
{
bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_1,
- MISC_REGISTERS_GPIO_OUTPUT_LOW, port);
+ MISC_REGISTERS_GPIO_OUTPUT_LOW, port);
msleep(1);
bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_1,
- MISC_REGISTERS_GPIO_OUTPUT_HIGH, port);
+ MISC_REGISTERS_GPIO_OUTPUT_HIGH, port);
}
static void bnx2x_save_spirom_version(struct bnx2x *bp, u8 port,
u16 fw_ver1, fw_ver2;
bnx2x_cl45_read(bp, phy, MDIO_PMA_DEVAD,
- MDIO_PMA_REG_ROM_VER1, &fw_ver1);
+ MDIO_PMA_REG_ROM_VER1, &fw_ver1);
bnx2x_cl45_read(bp, phy, MDIO_PMA_DEVAD,
- MDIO_PMA_REG_ROM_VER2, &fw_ver2);
+ MDIO_PMA_REG_ROM_VER2, &fw_ver2);
bnx2x_save_spirom_version(bp, port, (u32)(fw_ver1<<16 | fw_ver2),
phy->ver_addr);
}
if ((vars->ieee_fc &
MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_ASYMMETRIC) ==
MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_ASYMMETRIC) {
- val |= MDIO_AN_REG_ADV_PAUSE_ASYMMETRIC;
+ val |= MDIO_AN_REG_ADV_PAUSE_ASYMMETRIC;
}
if ((vars->ieee_fc &
MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH) ==
else if (vars->link_status & LINK_STATUS_AUTO_NEGOTIATE_COMPLETE) {
ret = 1;
bnx2x_cl45_read(bp, phy,
- MDIO_AN_DEVAD,
- MDIO_AN_REG_ADV_PAUSE, &ld_pause);
+ MDIO_AN_DEVAD,
+ MDIO_AN_REG_ADV_PAUSE, &ld_pause);
bnx2x_cl45_read(bp, phy,
- MDIO_AN_DEVAD,
- MDIO_AN_REG_LP_AUTO_NEG, &lp_pause);
+ MDIO_AN_DEVAD,
+ MDIO_AN_REG_LP_AUTO_NEG, &lp_pause);
pause_result = (ld_pause &
MDIO_AN_REG_ADV_PAUSE_MASK) >> 8;
pause_result |= (lp_pause &
/* Boot port from external ROM */
/* EDC grst */
bnx2x_cl45_write(bp, phy,
- MDIO_PMA_DEVAD,
- MDIO_PMA_REG_GEN_CTRL,
- 0x0001);
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_GEN_CTRL,
+ 0x0001);
/* ucode reboot and rst */
bnx2x_cl45_write(bp, phy,
- MDIO_PMA_DEVAD,
- MDIO_PMA_REG_GEN_CTRL,
- 0x008c);
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_GEN_CTRL,
+ 0x008c);
bnx2x_cl45_write(bp, phy,
- MDIO_PMA_DEVAD,
- MDIO_PMA_REG_MISC_CTRL1, 0x0001);
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_MISC_CTRL1, 0x0001);
/* Reset internal microprocessor */
bnx2x_cl45_write(bp, phy,
- MDIO_PMA_DEVAD,
- MDIO_PMA_REG_GEN_CTRL,
- MDIO_PMA_REG_GEN_CTRL_ROM_MICRO_RESET);
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_GEN_CTRL,
+ MDIO_PMA_REG_GEN_CTRL_ROM_MICRO_RESET);
/* Release srst bit */
bnx2x_cl45_write(bp, phy,
- MDIO_PMA_DEVAD,
- MDIO_PMA_REG_GEN_CTRL,
- MDIO_PMA_REG_GEN_CTRL_ROM_RESET_INTERNAL_MP);
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_GEN_CTRL,
+ MDIO_PMA_REG_GEN_CTRL_ROM_RESET_INTERNAL_MP);
/* Delay 100ms per the PHY specifications */
msleep(100);
/* Clear ser_boot_ctl bit */
bnx2x_cl45_write(bp, phy,
- MDIO_PMA_DEVAD,
- MDIO_PMA_REG_MISC_CTRL1, 0x0000);
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_MISC_CTRL1, 0x0000);
bnx2x_save_bcm_spirom_ver(bp, phy, port);
DP(NETIF_MSG_LINK,
/* Read 8073 HW revision*/
bnx2x_cl45_read(bp, phy,
- MDIO_PMA_DEVAD,
- MDIO_PMA_REG_8073_CHIP_REV, &val);
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_8073_CHIP_REV, &val);
if (val != 1) {
/* No need to workaround in 8073 A1 */
}
bnx2x_cl45_read(bp, phy,
- MDIO_PMA_DEVAD,
- MDIO_PMA_REG_ROM_VER2, &val);
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_ROM_VER2, &val);
/* SNR should be applied only for version 0x102 */
if (val != 0x102)
u16 val, cnt, cnt1 ;
bnx2x_cl45_read(bp, phy,
- MDIO_PMA_DEVAD,
- MDIO_PMA_REG_8073_CHIP_REV, &val);
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_8073_CHIP_REV, &val);
if (val > 0) {
/* No need to workaround in 8073 A1 */
for (cnt = 0; cnt < 1000; cnt++) {
bnx2x_cl45_read(bp, phy,
- MDIO_PMA_DEVAD,
- MDIO_PMA_REG_8073_SPEED_LINK_STATUS,
- &val);
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_8073_SPEED_LINK_STATUS,
+ &val);
/* If bit [14] = 0 or bit [13] = 0, continue on with
system initialization (XAUI work-around not required,
as these bits indicate 2.5G or 1G link up). */
gpio_port = params->port;
/* Restore normal power mode*/
bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2,
- MISC_REGISTERS_GPIO_OUTPUT_HIGH, gpio_port);
+ MISC_REGISTERS_GPIO_OUTPUT_HIGH, gpio_port);
bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_1,
- MISC_REGISTERS_GPIO_OUTPUT_HIGH, gpio_port);
+ MISC_REGISTERS_GPIO_OUTPUT_HIGH, gpio_port);
/* enable LASI */
bnx2x_cl45_write(bp, phy,
DP(NETIF_MSG_LINK, "Setting 8073 port %d into low power mode\n",
gpio_port);
bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2,
- MISC_REGISTERS_GPIO_OUTPUT_LOW,
- gpio_port);
+ MISC_REGISTERS_GPIO_OUTPUT_LOW,
+ gpio_port);
}
/******************************************************************/
DP(NETIF_MSG_LINK, "init 8705\n");
/* Restore normal power mode*/
bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2,
- MISC_REGISTERS_GPIO_OUTPUT_HIGH, params->port);
+ MISC_REGISTERS_GPIO_OUTPUT_HIGH, params->port);
/* HW reset */
bnx2x_ext_phy_hw_reset(bp, params->port);
bnx2x_cl45_write(bp, phy, MDIO_PMA_DEVAD, MDIO_PMA_REG_CTRL, 0xa040);
static u8 bnx2x_8726_read_sfp_module_eeprom(struct bnx2x_phy *phy,
struct link_params *params,
- u16 addr, u8 byte_cnt, u8 *o_buf)
+ u16 addr, u8 byte_cnt, u8 *o_buf)
{
struct bnx2x *bp = params->bp;
u16 val = 0;
/* Set the read command byte count */
bnx2x_cl45_write(bp, phy,
MDIO_PMA_DEVAD, MDIO_PMA_REG_SFP_TWO_WIRE_BYTE_CNT,
- (byte_cnt | 0xa000));
+ (byte_cnt | 0xa000));
/* Set the read command address */
bnx2x_cl45_write(bp, phy,
MDIO_PMA_DEVAD, MDIO_PMA_REG_SFP_TWO_WIRE_MEM_ADDR,
- addr);
+ addr);
/* Activate read command */
bnx2x_cl45_write(bp, phy,
MDIO_PMA_DEVAD, MDIO_PMA_REG_SFP_TWO_WIRE_CTRL,
- 0x2c0f);
+ 0x2c0f);
/* Wait up to 500us for command complete status */
for (i = 0; i < 100; i++) {
bnx2x_cl45_read(bp, phy,
- MDIO_PMA_DEVAD,
- MDIO_PMA_REG_SFP_TWO_WIRE_CTRL, &val);
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_SFP_TWO_WIRE_CTRL, &val);
if ((val & MDIO_PMA_REG_SFP_TWO_WIRE_CTRL_STATUS_MASK) ==
MDIO_PMA_REG_SFP_TWO_WIRE_STATUS_COMPLETE)
break;
/* Read the buffer */
for (i = 0; i < byte_cnt; i++) {
bnx2x_cl45_read(bp, phy,
- MDIO_PMA_DEVAD,
- MDIO_PMA_REG_8726_TWO_WIRE_DATA_BUF + i, &val);
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_8726_TWO_WIRE_DATA_BUF + i, &val);
o_buf[i] = (u8)(val & MDIO_PMA_REG_8726_TWO_WIRE_DATA_MASK);
}
for (i = 0; i < 100; i++) {
bnx2x_cl45_read(bp, phy,
- MDIO_PMA_DEVAD,
- MDIO_PMA_REG_SFP_TWO_WIRE_CTRL, &val);
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_SFP_TWO_WIRE_CTRL, &val);
if ((val & MDIO_PMA_REG_SFP_TWO_WIRE_CTRL_STATUS_MASK) ==
MDIO_PMA_REG_SFP_TWO_WIRE_STATUS_IDLE)
return 0;
static u8 bnx2x_8727_read_sfp_module_eeprom(struct bnx2x_phy *phy,
struct link_params *params,
- u16 addr, u8 byte_cnt, u8 *o_buf)
+ u16 addr, u8 byte_cnt, u8 *o_buf)
{
struct bnx2x *bp = params->bp;
u16 val, i;
/* Need to read from 1.8000 to clear it */
bnx2x_cl45_read(bp, phy,
- MDIO_PMA_DEVAD,
- MDIO_PMA_REG_SFP_TWO_WIRE_CTRL,
- &val);
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_SFP_TWO_WIRE_CTRL,
+ &val);
/* Set the read command byte count */
bnx2x_cl45_write(bp, phy,
- MDIO_PMA_DEVAD,
- MDIO_PMA_REG_SFP_TWO_WIRE_BYTE_CNT,
- ((byte_cnt < 2) ? 2 : byte_cnt));
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_SFP_TWO_WIRE_BYTE_CNT,
+ ((byte_cnt < 2) ? 2 : byte_cnt));
/* Set the read command address */
bnx2x_cl45_write(bp, phy,
- MDIO_PMA_DEVAD,
- MDIO_PMA_REG_SFP_TWO_WIRE_MEM_ADDR,
- addr);
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_SFP_TWO_WIRE_MEM_ADDR,
+ addr);
/* Set the destination address */
bnx2x_cl45_write(bp, phy,
- MDIO_PMA_DEVAD,
- 0x8004,
- MDIO_PMA_REG_8727_TWO_WIRE_DATA_BUF);
+ MDIO_PMA_DEVAD,
+ 0x8004,
+ MDIO_PMA_REG_8727_TWO_WIRE_DATA_BUF);
/* Activate read command */
bnx2x_cl45_write(bp, phy,
- MDIO_PMA_DEVAD,
- MDIO_PMA_REG_SFP_TWO_WIRE_CTRL,
- 0x8002);
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_SFP_TWO_WIRE_CTRL,
+ 0x8002);
/* Wait appropriate time for two-wire command to finish before
polling the status register */
msleep(1);
/* Wait up to 500us for command complete status */
for (i = 0; i < 100; i++) {
bnx2x_cl45_read(bp, phy,
- MDIO_PMA_DEVAD,
- MDIO_PMA_REG_SFP_TWO_WIRE_CTRL, &val);
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_SFP_TWO_WIRE_CTRL, &val);
if ((val & MDIO_PMA_REG_SFP_TWO_WIRE_CTRL_STATUS_MASK) ==
MDIO_PMA_REG_SFP_TWO_WIRE_STATUS_COMPLETE)
break;
/* Read the buffer */
for (i = 0; i < byte_cnt; i++) {
bnx2x_cl45_read(bp, phy,
- MDIO_PMA_DEVAD,
- MDIO_PMA_REG_8727_TWO_WIRE_DATA_BUF + i, &val);
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_8727_TWO_WIRE_DATA_BUF + i, &val);
o_buf[i] = (u8)(val & MDIO_PMA_REG_8727_TWO_WIRE_DATA_MASK);
}
for (i = 0; i < 100; i++) {
bnx2x_cl45_read(bp, phy,
- MDIO_PMA_DEVAD,
- MDIO_PMA_REG_SFP_TWO_WIRE_CTRL, &val);
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_SFP_TWO_WIRE_CTRL, &val);
if ((val & MDIO_PMA_REG_SFP_TWO_WIRE_CTRL_STATUS_MASK) ==
MDIO_PMA_REG_SFP_TWO_WIRE_STATUS_IDLE)
return 0;
return -EINVAL;
}
-static u8 bnx2x_read_sfp_module_eeprom(struct bnx2x_phy *phy,
- struct link_params *params, u16 addr,
- u8 byte_cnt, u8 *o_buf)
+u8 bnx2x_read_sfp_module_eeprom(struct bnx2x_phy *phy,
+ struct link_params *params, u16 addr,
+ u8 byte_cnt, u8 *o_buf)
{
if (phy->type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8726)
return bnx2x_8726_read_sfp_module_eeprom(phy, params, addr,
- byte_cnt, o_buf);
+ byte_cnt, o_buf);
else if (phy->type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727)
return bnx2x_8727_read_sfp_module_eeprom(phy, params, addr,
- byte_cnt, o_buf);
+ byte_cnt, o_buf);
return -EINVAL;
}
static u8 bnx2x_get_edc_mode(struct bnx2x_phy *phy,
struct link_params *params,
- u16 *edc_mode)
+ u16 *edc_mode)
{
struct bnx2x *bp = params->bp;
u8 val, check_limiting_mode = 0;
/* format the warning message */
if (bnx2x_read_sfp_module_eeprom(phy,
params,
- SFP_EEPROM_VENDOR_NAME_ADDR,
- SFP_EEPROM_VENDOR_NAME_SIZE,
- (u8 *)vendor_name))
+ SFP_EEPROM_VENDOR_NAME_ADDR,
+ SFP_EEPROM_VENDOR_NAME_SIZE,
+ (u8 *)vendor_name))
vendor_name[0] = '\0';
else
vendor_name[SFP_EEPROM_VENDOR_NAME_SIZE] = '\0';
if (bnx2x_read_sfp_module_eeprom(phy,
params,
- SFP_EEPROM_PART_NO_ADDR,
- SFP_EEPROM_PART_NO_SIZE,
- (u8 *)vendor_pn))
+ SFP_EEPROM_PART_NO_ADDR,
+ SFP_EEPROM_PART_NO_SIZE,
+ (u8 *)vendor_pn))
vendor_pn[0] = '\0';
else
vendor_pn[SFP_EEPROM_PART_NO_SIZE] = '\0';
u16 cur_limiting_mode;
bnx2x_cl45_read(bp, phy,
- MDIO_PMA_DEVAD,
- MDIO_PMA_REG_ROM_VER2,
- &cur_limiting_mode);
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_ROM_VER2,
+ &cur_limiting_mode);
DP(NETIF_MSG_LINK, "Current Limiting mode is 0x%x\n",
cur_limiting_mode);
if (edc_mode == EDC_MODE_LIMITING) {
- DP(NETIF_MSG_LINK,
- "Setting LIMITING MODE\n");
+ DP(NETIF_MSG_LINK, "Setting LIMITING MODE\n");
bnx2x_cl45_write(bp, phy,
MDIO_PMA_DEVAD,
MDIO_PMA_REG_ROM_VER2,
return 0;
bnx2x_cl45_write(bp, phy,
- MDIO_PMA_DEVAD,
- MDIO_PMA_REG_LRM_MODE,
- 0);
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_LRM_MODE,
+ 0);
bnx2x_cl45_write(bp, phy,
- MDIO_PMA_DEVAD,
- MDIO_PMA_REG_ROM_VER2,
- 0x128);
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_ROM_VER2,
+ 0x128);
bnx2x_cl45_write(bp, phy,
- MDIO_PMA_DEVAD,
- MDIO_PMA_REG_MISC_CTRL0,
- 0x4008);
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_MISC_CTRL0,
+ 0x4008);
bnx2x_cl45_write(bp, phy,
- MDIO_PMA_DEVAD,
- MDIO_PMA_REG_LRM_MODE,
- 0xaaaa);
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_LRM_MODE,
+ 0xaaaa);
}
return 0;
}
static u8 bnx2x_8727_set_limiting_mode(struct bnx2x *bp,
struct bnx2x_phy *phy,
- u16 edc_mode)
+ u16 edc_mode)
{
u16 phy_identifier;
u16 rom_ver2_val;
bnx2x_cl45_read(bp, phy,
- MDIO_PMA_DEVAD,
- MDIO_PMA_REG_PHY_IDENTIFIER,
- &phy_identifier);
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_PHY_IDENTIFIER,
+ &phy_identifier);
bnx2x_cl45_write(bp, phy,
- MDIO_PMA_DEVAD,
- MDIO_PMA_REG_PHY_IDENTIFIER,
- (phy_identifier & ~(1<<9)));
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_PHY_IDENTIFIER,
+ (phy_identifier & ~(1<<9)));
bnx2x_cl45_read(bp, phy,
- MDIO_PMA_DEVAD,
- MDIO_PMA_REG_ROM_VER2,
- &rom_ver2_val);
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_ROM_VER2,
+ &rom_ver2_val);
/* Keep the MSB 8-bits, and set the LSB 8-bits with the edc_mode */
bnx2x_cl45_write(bp, phy,
- MDIO_PMA_DEVAD,
- MDIO_PMA_REG_ROM_VER2,
- (rom_ver2_val & 0xff00) | (edc_mode & 0x00ff));
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_ROM_VER2,
+ (rom_ver2_val & 0xff00) | (edc_mode & 0x00ff));
bnx2x_cl45_write(bp, phy,
- MDIO_PMA_DEVAD,
- MDIO_PMA_REG_PHY_IDENTIFIER,
- (phy_identifier | (1<<9)));
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_PHY_IDENTIFIER,
+ (phy_identifier | (1<<9)));
return 0;
}
if (bnx2x_get_edc_mode(phy, params, &edc_mode) != 0) {
DP(NETIF_MSG_LINK, "Failed to get valid module type\n");
return -EINVAL;
- } else if (bnx2x_verify_sfp_module(phy, params) !=
- 0) {
+ } else if (bnx2x_verify_sfp_module(phy, params) != 0) {
/* check SFP+ module compatibility */
DP(NETIF_MSG_LINK, "Module verification failed!!\n");
rc = -EINVAL;
DP(NETIF_MSG_LINK, "SFP+ module is not initialized\n");
} else {
u32 val = REG_RD(bp, params->shmem_base +
- offsetof(struct shmem_region, dev_info.
- port_feature_config[params->port].
- config));
+ offsetof(struct shmem_region, dev_info.
+ port_feature_config[params->port].
+ config));
bnx2x_set_gpio_int(bp, MISC_REGISTERS_GPIO_3,
MISC_REGISTERS_GPIO_INT_OUTPUT_SET,
u16 cnt, val;
struct bnx2x *bp = params->bp;
bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2,
- MISC_REGISTERS_GPIO_OUTPUT_HIGH, params->port);
+ MISC_REGISTERS_GPIO_OUTPUT_HIGH, params->port);
/* HW reset */
bnx2x_ext_phy_hw_reset(bp, params->port);
bnx2x_cl45_write(bp, phy, MDIO_PMA_DEVAD, MDIO_PMA_REG_CTRL, 0xa040);
/* Set soft reset */
bnx2x_cl45_write(bp, phy,
- MDIO_PMA_DEVAD,
- MDIO_PMA_REG_GEN_CTRL,
- MDIO_PMA_REG_GEN_CTRL_ROM_MICRO_RESET);
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_GEN_CTRL,
+ MDIO_PMA_REG_GEN_CTRL_ROM_MICRO_RESET);
bnx2x_cl45_write(bp, phy,
- MDIO_PMA_DEVAD,
- MDIO_PMA_REG_MISC_CTRL1, 0x0001);
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_MISC_CTRL1, 0x0001);
bnx2x_cl45_write(bp, phy,
- MDIO_PMA_DEVAD,
- MDIO_PMA_REG_GEN_CTRL,
- MDIO_PMA_REG_GEN_CTRL_ROM_RESET_INTERNAL_MP);
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_GEN_CTRL,
+ MDIO_PMA_REG_GEN_CTRL_ROM_RESET_INTERNAL_MP);
/* wait for 150ms for microcode load */
msleep(150);
/* Disable serial boot control, tristates pins SS_N, SCK, MOSI, MISO */
bnx2x_cl45_write(bp, phy,
- MDIO_PMA_DEVAD,
- MDIO_PMA_REG_MISC_CTRL1, 0x0000);
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_MISC_CTRL1, 0x0000);
msleep(200);
bnx2x_save_bcm_spirom_ver(bp, phy, params->port);
/* Set GPIO3 to trigger SFP+ module insertion/removal */
bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_3,
- MISC_REGISTERS_GPIO_INPUT_HI_Z, params->port);
+ MISC_REGISTERS_GPIO_INPUT_HI_Z, params->port);
/* The GPIO should be swapped if the swap register is set and active */
swap_val = REG_RD(bp, NIG_REG_PORT_SWAP);
swap_override = REG_RD(bp, NIG_REG_STRAP_OVERRIDE);
port = (swap_val && swap_override) ^ 1;
bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_1,
- MISC_REGISTERS_GPIO_OUTPUT_LOW, port);
+ MISC_REGISTERS_GPIO_OUTPUT_LOW, port);
}
static u8 bnx2x_8727_config_init(struct bnx2x_phy *phy,
port_feature_config[params->port].
config));
bnx2x_cl45_read(bp, phy,
- MDIO_PMA_DEVAD,
- MDIO_PMA_REG_PHY_IDENTIFIER, &mod_abs);
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_PHY_IDENTIFIER, &mod_abs);
if (mod_abs & (1<<8)) {
/* Module is absent */
if (!(phy->flags & FLAGS_NOC))
mod_abs &= ~(1<<9);
bnx2x_cl45_write(bp, phy,
- MDIO_PMA_DEVAD,
- MDIO_PMA_REG_PHY_IDENTIFIER, mod_abs);
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_PHY_IDENTIFIER, mod_abs);
/* Clear RX alarm since it stays up as long as
the mod_abs wasn't changed */
bnx2x_cl45_read(bp, phy,
- MDIO_PMA_DEVAD,
- MDIO_PMA_REG_RX_ALARM, &rx_alarm_status);
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_RX_ALARM, &rx_alarm_status);
} else {
/* Module is present */
struct bnx2x *bp = params->bp;
/* Restore normal power mode*/
bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2,
- MISC_REGISTERS_GPIO_OUTPUT_HIGH, params->port);
+ MISC_REGISTERS_GPIO_OUTPUT_HIGH, params->port);
/* HW reset */
bnx2x_ext_phy_hw_reset(bp, params->port);
}
static u8 bnx2x_848xx_read_status(struct bnx2x_phy *phy,
- struct link_params *params,
- struct link_vars *vars)
+ struct link_params *params,
+ struct link_vars *vars)
{
struct bnx2x *bp = params->bp;
u16 val, val1, val2;
struct link_params *params)
{
bnx2x_set_gpio(params->bp, MISC_REGISTERS_GPIO_1,
- MISC_REGISTERS_GPIO_OUTPUT_LOW, 0);
+ MISC_REGISTERS_GPIO_OUTPUT_LOW, 0);
bnx2x_set_gpio(params->bp, MISC_REGISTERS_GPIO_1,
- MISC_REGISTERS_GPIO_OUTPUT_LOW, 1);
+ MISC_REGISTERS_GPIO_OUTPUT_LOW, 1);
}
static void bnx2x_8481_link_reset(struct bnx2x_phy *phy,
else
port = params->port;
bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_3,
- MISC_REGISTERS_GPIO_OUTPUT_LOW,
- port);
+ MISC_REGISTERS_GPIO_OUTPUT_LOW,
+ port);
}
static void bnx2x_848xx_set_link_led(struct bnx2x_phy *phy,
/* Set LED masks */
bnx2x_cl45_write(bp, phy,
- MDIO_PMA_DEVAD,
- MDIO_PMA_REG_8481_LED1_MASK,
- 0x0);
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_8481_LED1_MASK,
+ 0x0);
bnx2x_cl45_write(bp, phy,
- MDIO_PMA_DEVAD,
- MDIO_PMA_REG_8481_LED2_MASK,
- 0x0);
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_8481_LED2_MASK,
+ 0x0);
bnx2x_cl45_write(bp, phy,
- MDIO_PMA_DEVAD,
- MDIO_PMA_REG_8481_LED3_MASK,
- 0x0);
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_8481_LED3_MASK,
+ 0x0);
bnx2x_cl45_write(bp, phy,
- MDIO_PMA_DEVAD,
- MDIO_PMA_REG_8481_LED5_MASK,
- 0x20);
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_8481_LED5_MASK,
+ 0x20);
} else {
bnx2x_cl45_write(bp, phy,
val |= 0x2492;
bnx2x_cl45_write(bp, phy,
- MDIO_PMA_DEVAD,
- MDIO_PMA_REG_8481_LINK_SIGNAL,
- val);
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_8481_LINK_SIGNAL,
+ val);
/* Set LED masks */
bnx2x_cl45_write(bp, phy,
- MDIO_PMA_DEVAD,
- MDIO_PMA_REG_8481_LED1_MASK,
- 0x0);
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_8481_LED1_MASK,
+ 0x0);
bnx2x_cl45_write(bp, phy,
- MDIO_PMA_DEVAD,
- MDIO_PMA_REG_8481_LED2_MASK,
- 0x20);
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_8481_LED2_MASK,
+ 0x20);
bnx2x_cl45_write(bp, phy,
- MDIO_PMA_DEVAD,
- MDIO_PMA_REG_8481_LED3_MASK,
- 0x20);
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_8481_LED3_MASK,
+ 0x20);
bnx2x_cl45_write(bp, phy,
- MDIO_PMA_DEVAD,
- MDIO_PMA_REG_8481_LED5_MASK,
- 0x0);
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_8481_LED5_MASK,
+ 0x0);
} else {
bnx2x_cl45_write(bp, phy,
- MDIO_PMA_DEVAD,
- MDIO_PMA_REG_8481_LED1_MASK,
- 0x20);
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_8481_LED1_MASK,
+ 0x20);
}
break;
&val);
if (!((val &
- MDIO_PMA_REG_8481_LINK_SIGNAL_LED4_ENABLE_MASK)
- >> MDIO_PMA_REG_8481_LINK_SIGNAL_LED4_ENABLE_SHIFT)){
+ MDIO_PMA_REG_8481_LINK_SIGNAL_LED4_ENABLE_MASK)
+ >> MDIO_PMA_REG_8481_LINK_SIGNAL_LED4_ENABLE_SHIFT)) {
DP(NETIF_MSG_LINK, "Seting LINK_SIGNAL\n");
bnx2x_cl45_write(bp, phy,
MDIO_PMA_DEVAD,
/* Set LED masks */
bnx2x_cl45_write(bp, phy,
- MDIO_PMA_DEVAD,
- MDIO_PMA_REG_8481_LED1_MASK,
- 0x10);
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_8481_LED1_MASK,
+ 0x10);
bnx2x_cl45_write(bp, phy,
- MDIO_PMA_DEVAD,
- MDIO_PMA_REG_8481_LED2_MASK,
- 0x80);
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_8481_LED2_MASK,
+ 0x80);
bnx2x_cl45_write(bp, phy,
- MDIO_PMA_DEVAD,
- MDIO_PMA_REG_8481_LED3_MASK,
- 0x98);
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_8481_LED3_MASK,
+ 0x98);
bnx2x_cl45_write(bp, phy,
- MDIO_PMA_DEVAD,
- MDIO_PMA_REG_8481_LED5_MASK,
- 0x40);
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_8481_LED5_MASK,
+ 0x40);
} else {
bnx2x_cl45_write(bp, phy,
/* Restore normal power mode*/
bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2,
- MISC_REGISTERS_GPIO_OUTPUT_HIGH, params->port);
+ MISC_REGISTERS_GPIO_OUTPUT_HIGH, params->port);
/* HW reset */
bnx2x_ext_phy_hw_reset(bp, params->port);
bnx2x_wait_reset_complete(bp, phy);
u16 val, cnt;
bnx2x_cl45_read(bp, phy,
- MDIO_PMA_DEVAD,
- MDIO_PMA_REG_7101_RESET, &val);
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_7101_RESET, &val);
for (cnt = 0; cnt < 10; cnt++) {
msleep(50);
/* Writes a self-clearing reset */
bnx2x_cl45_write(bp, phy,
- MDIO_PMA_DEVAD,
- MDIO_PMA_REG_7101_RESET,
- (val | (1<<15)));
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_7101_RESET,
+ (val | (1<<15)));
/* Wait for clear */
bnx2x_cl45_read(bp, phy,
- MDIO_PMA_DEVAD,
- MDIO_PMA_REG_7101_RESET, &val);
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_7101_RESET, &val);
if ((val & (1<<15)) == 0)
break;
struct link_params *params) {
/* Low power mode is controlled by GPIO 2 */
bnx2x_set_gpio(params->bp, MISC_REGISTERS_GPIO_2,
- MISC_REGISTERS_GPIO_OUTPUT_LOW, params->port);
+ MISC_REGISTERS_GPIO_OUTPUT_LOW, params->port);
/* The PHY reset is controlled by GPIO 1 */
bnx2x_set_gpio(params->bp, MISC_REGISTERS_GPIO_1,
- MISC_REGISTERS_GPIO_OUTPUT_LOW, params->port);
+ MISC_REGISTERS_GPIO_OUTPUT_LOW, params->port);
}
static void bnx2x_7101_set_link_led(struct bnx2x_phy *phy,
.supported = 0,
.media_type = ETH_PHY_NOT_PRESENT,
.ver_addr = 0,
- .req_flow_ctrl = 0,
- .req_line_speed = 0,
- .speed_cap_mask = 0,
+ .req_flow_ctrl = 0,
+ .req_line_speed = 0,
+ .speed_cap_mask = 0,
.req_duplex = 0,
.rsrv = 0,
.config_init = (config_init_t)NULL,
.media_type = ETH_PHY_UNSPECIFIED,
.ver_addr = 0,
.req_flow_ctrl = 0,
- .req_line_speed = 0,
- .speed_cap_mask = 0,
+ .req_line_speed = 0,
+ .speed_cap_mask = 0,
.req_duplex = 0,
.rsrv = 0,
.config_init = (config_init_t)bnx2x_init_serdes,
.media_type = ETH_PHY_UNSPECIFIED,
.ver_addr = 0,
.req_flow_ctrl = 0,
- .req_line_speed = 0,
- .speed_cap_mask = 0,
+ .req_line_speed = 0,
+ .speed_cap_mask = 0,
.req_duplex = 0,
.rsrv = 0,
.config_init = (config_init_t)bnx2x_init_xgxs,
.media_type = ETH_PHY_BASE_T,
.ver_addr = 0,
.req_flow_ctrl = 0,
- .req_line_speed = 0,
- .speed_cap_mask = 0,
+ .req_line_speed = 0,
+ .speed_cap_mask = 0,
.req_duplex = 0,
.rsrv = 0,
.config_init = (config_init_t)bnx2x_7101_config_init,
SUPPORTED_Asym_Pause),
.media_type = ETH_PHY_UNSPECIFIED,
.ver_addr = 0,
- .req_flow_ctrl = 0,
- .req_line_speed = 0,
- .speed_cap_mask = 0,
+ .req_flow_ctrl = 0,
+ .req_line_speed = 0,
+ .speed_cap_mask = 0,
.req_duplex = 0,
.rsrv = 0,
.config_init = (config_init_t)bnx2x_8073_config_init,
if (phy_index == INT_PHY || phy_index == EXT_PHY1) {
rx = REG_RD(bp, shmem_base +
offsetof(struct shmem_region,
- dev_info.port_hw_config[port].xgxs_config_rx[i<<1]));
+ dev_info.port_hw_config[port].xgxs_config_rx[i<<1]));
tx = REG_RD(bp, shmem_base +
offsetof(struct shmem_region,
- dev_info.port_hw_config[port].xgxs_config_tx[i<<1]));
+ dev_info.port_hw_config[port].xgxs_config_tx[i<<1]));
} else {
rx = REG_RD(bp, shmem_base +
offsetof(struct shmem_region,
- dev_info.port_hw_config[port].xgxs_config2_rx[i<<1]));
+ dev_info.port_hw_config[port].xgxs_config2_rx[i<<1]));
tx = REG_RD(bp, shmem_base +
offsetof(struct shmem_region,
- dev_info.port_hw_config[port].xgxs_config2_rx[i<<1]));
+ dev_info.port_hw_config[port].xgxs_config2_rx[i<<1]));
}
phy->rx_preemphasis[i << 1] = ((rx>>16) & 0xffff);
phy->ver_addr = shmem_base + offsetof(struct shmem_region,
port_mb[port].ext_phy_fw_version);
- /* Check specific mdc mdio settings */
- if (config2 & SHARED_HW_CFG_MDC_MDIO_ACCESS1_MASK)
- mdc_mdio_access = config2 &
- SHARED_HW_CFG_MDC_MDIO_ACCESS1_MASK;
+ /* Check specific mdc mdio settings */
+ if (config2 & SHARED_HW_CFG_MDC_MDIO_ACCESS1_MASK)
+ mdc_mdio_access = config2 &
+ SHARED_HW_CFG_MDC_MDIO_ACCESS1_MASK;
} else {
u32 size = REG_RD(bp, shmem2_base);
/* Populate the default phy configuration for MF mode */
if (phy_index == EXT_PHY2) {
link_config = REG_RD(bp, params->shmem_base +
- offsetof(struct shmem_region, dev_info.
+ offsetof(struct shmem_region, dev_info.
port_feature_config[params->port].link_config2));
phy->speed_cap_mask = REG_RD(bp, params->shmem_base +
- offsetof(struct shmem_region, dev_info.
+ offsetof(struct shmem_region,
+ dev_info.
port_hw_config[params->port].speed_capability_mask2));
} else {
link_config = REG_RD(bp, params->shmem_base +
- offsetof(struct shmem_region, dev_info.
+ offsetof(struct shmem_region, dev_info.
port_feature_config[params->port].link_config));
phy->speed_cap_mask = REG_RD(bp, params->shmem_base +
- offsetof(struct shmem_region, dev_info.
- port_hw_config[params->port].speed_capability_mask));
+ offsetof(struct shmem_region,
+ dev_info.
+ port_hw_config[params->port].speed_capability_mask));
}
DP(NETIF_MSG_LINK, "Default config phy idx %x cfg 0x%x speed_cap_mask"
" 0x%x\n", phy_index, link_config, phy->speed_cap_mask);
else if (phy_index == EXT_PHY2)
actual_phy_idx = EXT_PHY1;
}
- params->phy[actual_phy_idx].req_flow_ctrl =
+ params->phy[actual_phy_idx].req_flow_ctrl =
params->req_flow_ctrl[link_cfg_idx];
params->phy[actual_phy_idx].req_line_speed =
/* set bmac loopback */
bnx2x_bmac_enable(params, vars, 1);
- REG_WR(bp, NIG_REG_EGRESS_DRAIN0_MODE +
- params->port*4, 0);
+ REG_WR(bp, NIG_REG_EGRESS_DRAIN0_MODE + params->port*4, 0);
} else if (params->loopback_mode == LOOPBACK_EMAC) {
/* set bmac loopback */
bnx2x_emac_enable(params, vars, 1);
bnx2x_emac_program(params, vars);
- REG_WR(bp, NIG_REG_EGRESS_DRAIN0_MODE +
- params->port*4, 0);
+ REG_WR(bp, NIG_REG_EGRESS_DRAIN0_MODE + params->port*4, 0);
} else if ((params->loopback_mode == LOOPBACK_XGXS) ||
(params->loopback_mode == LOOPBACK_EXT_PHY)) {
bnx2x_emac_program(params, vars);
bnx2x_emac_enable(params, vars, 0);
} else
- bnx2x_bmac_enable(params, vars, 0);
-
+ bnx2x_bmac_enable(params, vars, 0);
if (params->loopback_mode == LOOPBACK_XGXS) {
/* set 10G XGXS loopback */
params->phy[INT_PHY].config_loopback(
params);
}
}
-
- REG_WR(bp, NIG_REG_EGRESS_DRAIN0_MODE +
- params->port*4, 0);
+ REG_WR(bp, NIG_REG_EGRESS_DRAIN0_MODE + params->port*4, 0);
bnx2x_set_led(params, vars,
LED_MODE_OPER, vars->line_speed);
return 0;
}
u8 bnx2x_link_reset(struct link_params *params, struct link_vars *vars,
- u8 reset_ext_phy)
+ u8 reset_ext_phy)
{
struct bnx2x *bp = params->bp;
u8 phy_index, port = params->port, clear_latch_ind = 0;
vars->link_status = 0;
bnx2x_update_mng(params, vars->link_status);
bnx2x_bits_dis(bp, NIG_REG_MASK_INTERRUPT_PORT0 + port*4,
- (NIG_MASK_XGXS0_LINK_STATUS |
- NIG_MASK_XGXS0_LINK10G |
- NIG_MASK_SERDES0_LINK_STATUS |
- NIG_MASK_MI_INT));
+ (NIG_MASK_XGXS0_LINK_STATUS |
+ NIG_MASK_XGXS0_LINK10G |
+ NIG_MASK_SERDES0_LINK_STATUS |
+ NIG_MASK_MI_INT));
/* activate nig drain */
REG_WR(bp, NIG_REG_EGRESS_DRAIN0_MODE + port*4, 1);
/* disable attentions */
bnx2x_bits_dis(bp, NIG_REG_MASK_INTERRUPT_PORT0 +
port_of_path*4,
- (NIG_MASK_XGXS0_LINK_STATUS |
- NIG_MASK_XGXS0_LINK10G |
- NIG_MASK_SERDES0_LINK_STATUS |
- NIG_MASK_MI_INT));
+ (NIG_MASK_XGXS0_LINK_STATUS |
+ NIG_MASK_XGXS0_LINK10G |
+ NIG_MASK_SERDES0_LINK_STATUS |
+ NIG_MASK_MI_INT));
/* Need to take the phy out of low power mode in order
to write to access its registers */
bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2,
- MISC_REGISTERS_GPIO_OUTPUT_HIGH, port);
+ MISC_REGISTERS_GPIO_OUTPUT_HIGH,
+ port);
/* Reset the phy */
bnx2x_cl45_write(bp, &phy[port],
- MDIO_PMA_DEVAD,
- MDIO_PMA_REG_CTRL,
- 1<<15);
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_CTRL,
+ 1<<15);
}
/* Add delay of 150ms after reset */
/* Only set bit 10 = 1 (Tx power down) */
bnx2x_cl45_read(bp, phy_blk[port],
- MDIO_PMA_DEVAD,
- MDIO_PMA_REG_TX_POWER_DOWN, &val);
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_TX_POWER_DOWN, &val);
/* Phase1 of TX_POWER_DOWN reset */
bnx2x_cl45_write(bp, phy_blk[port],
- MDIO_PMA_DEVAD,
- MDIO_PMA_REG_TX_POWER_DOWN,
- (val | 1<<10));
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_TX_POWER_DOWN,
+ (val | 1<<10));
}
/* Toggle Transmitter: Power down and then up with 600ms
/* Phase2 of POWER_DOWN_RESET */
/* Release bit 10 (Release Tx power down) */
bnx2x_cl45_read(bp, phy_blk[port],
- MDIO_PMA_DEVAD,
- MDIO_PMA_REG_TX_POWER_DOWN, &val);
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_TX_POWER_DOWN, &val);
bnx2x_cl45_write(bp, phy_blk[port],
- MDIO_PMA_DEVAD,
- MDIO_PMA_REG_TX_POWER_DOWN, (val & (~(1<<10))));
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_TX_POWER_DOWN, (val & (~(1<<10))));
msleep(15);
/* Read modify write the SPI-ROM version select register */
bnx2x_cl45_read(bp, phy_blk[port],
- MDIO_PMA_DEVAD,
- MDIO_PMA_REG_EDC_FFE_MAIN, &val);
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_EDC_FFE_MAIN, &val);
bnx2x_cl45_write(bp, phy_blk[port],
- MDIO_PMA_DEVAD,
- MDIO_PMA_REG_EDC_FFE_MAIN, (val | (1<<12)));
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_EDC_FFE_MAIN, (val | (1<<12)));
/* set GPIO2 back to LOW */
bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2,
- MISC_REGISTERS_GPIO_OUTPUT_LOW, port);
+ MISC_REGISTERS_GPIO_OUTPUT_LOW, port);
}
return 0;
}
/* Set fault module detected LED on */
bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_0,
- MISC_REGISTERS_GPIO_HIGH,
- port);
+ MISC_REGISTERS_GPIO_HIGH,
+ port);
}
return 0;
struct bnx2x_phy phy[PORT_MAX];
struct bnx2x_phy *phy_blk[PORT_MAX];
s8 port_of_path;
- swap_val = REG_RD(bp, NIG_REG_PORT_SWAP);
- swap_override = REG_RD(bp, NIG_REG_STRAP_OVERRIDE);
+ swap_val = REG_RD(bp, NIG_REG_PORT_SWAP);
+ swap_override = REG_RD(bp, NIG_REG_STRAP_OVERRIDE);
port = 1;
/* Reset the phy */
bnx2x_cl45_write(bp, &phy[port],
- MDIO_PMA_DEVAD,
- MDIO_PMA_REG_CTRL,
- 1<<15);
+ MDIO_PMA_DEVAD, MDIO_PMA_REG_CTRL, 1<<15);
}
/* Add delay of 150ms after reset */
}
/* PART2 - Download firmware to both phys */
for (port = PORT_MAX - 1; port >= PORT_0; port--) {
- if (CHIP_IS_E2(bp))
+ if (CHIP_IS_E2(bp))
port_of_path = 0;
else
port_of_path = port;
projects / platform / kernel / linux-amlogic.git / commitdiff