serial: pl01x: Add support for devices with the rate pre-configured.

For Raspberry Pi, we had the input clock rate to the pl011 fixed in
the rpi.c file, but it may be changed by firmware due to user changes
to config.txt.  Since the firmware always sets up the uart (default
115200 output unless the user changes it), we can just skip our own
uart init to simplify the boot process and more reliably get serial
output.

Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Tom Rini <trini@konsulko.com>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>

diff --git a/board/raspberrypi/rpi/rpi.c b/board/raspberrypi/rpi/rpi.c
index 1d3a4e0..da4b6ff 100644 (file)
--- a/board/raspberrypi/rpi/rpi.c
+++ b/board/raspberrypi/rpi/rpi.c
@@ -37,7 +37,7 @@ static const struct pl01x_serial_platdata serial_platdata = {
        .base = 0x20201000,
 #endif
        .type = TYPE_PL011,
-       .clock = 3000000,
+       .skip_init = true,
 };
 
 U_BOOT_DEVICE(bcm2835_serials) = {

diff --git a/drivers/serial/serial_pl01x.c b/drivers/serial/serial_pl01x.c
index 552c945..6f83835 100644 (file)
--- a/drivers/serial/serial_pl01x.c
+++ b/drivers/serial/serial_pl01x.c
@@ -284,7 +284,10 @@ static int pl01x_serial_setbrg(struct udevice *dev, int baudrate)
        struct pl01x_serial_platdata *plat = dev_get_platdata(dev);
        struct pl01x_priv *priv = dev_get_priv(dev);
 
-       pl01x_generic_setbrg(priv->regs, priv->type, plat->clock, baudrate);
+       if (!plat->skip_init) {
+               pl01x_generic_setbrg(priv->regs, priv->type, plat->clock,
+                                    baudrate);
+       }
 
        return 0;
 }
@@ -296,7 +299,10 @@ static int pl01x_serial_probe(struct udevice *dev)
 
        priv->regs = (struct pl01x_regs *)plat->base;
        priv->type = plat->type;
-       return pl01x_generic_serial_init(priv->regs, priv->type);
+       if (!plat->skip_init)
+               return pl01x_generic_serial_init(priv->regs, priv->type);
+       else
+               return 0;
 }
 
 static int pl01x_serial_getc(struct udevice *dev)

diff --git a/include/dm/platform_data/serial_pl01x.h b/include/dm/platform_data/serial_pl01x.h
index 5e068f3..ccfa808 100644 (file)
--- a/include/dm/platform_data/serial_pl01x.h
+++ b/include/dm/platform_data/serial_pl01x.h
@@ -17,11 +17,14 @@ enum pl01x_type {
  * @base: Register base address
  * @type: Port type
  * @clock: Input clock rate, used for calculating the baud rate divisor
+ * @skip_init: Don't attempt to change port configuration (also means @clock
+ * is ignored)
  */
 struct pl01x_serial_platdata {
        unsigned long base;
        enum pl01x_type type;
        unsigned int clock;
+       bool skip_init;
 };
 
 #endif