imx6ull-phytec-segin-ff-rdk-emmc.dtb \
imx6ull-dart-6ul.dtb \
imx6ull-somlabs-visionsom.dtb \
+ imx6ulz-bsh-smm-m2.dtb \
imx6ulz-14x14-evk.dtb
dtb-$(CONFIG_ARCH_MX6) += \
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2022 BSH Hausgeraete GmbH
+ *
+ * Author: Michael Trimarchi <michael@amarulasolutions.com>
+ */
+
+&{/soc} {
+ u-boot,dm-pre-reloc;
+};
+
+&aips2 {
+ u-boot,dm-pre-reloc;
+};
+
+&iomuxc {
+ u-boot,dm-pre-reloc;
+};
+
+&iomuxc_snvs {
+ u-boot,dm-pre-reloc;
+};
+
+&uart4 {
+ u-boot,dm-pre-reloc;
+};
+
+&pinctrl_uart4 {
+ u-boot,dm-pre-reloc;
+};
+
+&gpmi {
+ u-boot,dm-spl;
+ u-boot,dm-pre-reloc;
+};
--- /dev/null
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Copyright (C) 2021 BSH Hausgeraete GmbH
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/input/input.h>
+#include "imx6ulz.dtsi"
+
+/ {
+ model = "BSH SMM M2";
+ compatible = "bsh,imx6ulz-bsh-smm-m2", "fsl,imx6ull", "fsl,imx6ulz";
+
+ chosen {
+ stdout-path = &uart4;
+ };
+
+ usdhc2_pwrseq: usdhc2-pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ reset-gpios = <&gpio2 21 GPIO_ACTIVE_LOW>;
+ };
+};
+
+&gpmi {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpmi_nand>;
+ nand-on-flash-bbt;
+ status = "okay";
+};
+
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart3>;
+ uart-has-rtscts;
+ status = "okay";
+
+ bluetooth {
+ compatible = "brcm,bcm4330-bt";
+ max-speed = <3000000>;
+ shutdown-gpios = <&gpio1 1 GPIO_ACTIVE_HIGH>;
+ device-wakeup-gpios = <&gpio2 17 GPIO_ACTIVE_HIGH>;
+ host-wakeup-gpios = <&gpio2 13 GPIO_ACTIVE_HIGH>;
+ };
+};
+
+&uart4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart4>;
+ status = "okay";
+};
+
+&usbotg1 {
+ dr_mode = "peripheral";
+ srp-disable;
+ hnp-disable;
+ adp-disable;
+ status = "okay";
+};
+
+&usbphy1 {
+ fsl,tx-d-cal = <106>;
+};
+
+&usdhc2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_wlan>;
+ bus-width = <4>;
+ no-1-8-v;
+ non-removable;
+ cap-power-off-card;
+ keep-power-in-suspend;
+ cap-sdio-irq;
+ mmc-pwrseq = <&usdhc2_pwrseq>;
+ status = "okay";
+
+ brcmf: wifi@1 {
+ reg = <1>;
+ compatible = "brcm,bcm4329-fmac";
+ interrupt-parent = <&gpio1>;
+ interrupts = <18 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "host-wake";
+ };
+};
+
+&wdog1 {
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl_gpmi_nand: gpmi-nand {
+ fsl,pins = <
+ MX6UL_PAD_NAND_CLE__RAWNAND_CLE 0xb0b1
+ MX6UL_PAD_NAND_ALE__RAWNAND_ALE 0xb0b1
+ MX6UL_PAD_NAND_WP_B__RAWNAND_WP_B 0xb0b1
+ MX6UL_PAD_NAND_READY_B__RAWNAND_READY_B 0xb000
+ MX6UL_PAD_NAND_CE0_B__RAWNAND_CE0_B 0xb0b1
+ MX6UL_PAD_NAND_RE_B__RAWNAND_RE_B 0xb0b1
+ MX6UL_PAD_NAND_WE_B__RAWNAND_WE_B 0xb0b1
+ MX6UL_PAD_NAND_DATA00__RAWNAND_DATA00 0xb0b1
+ MX6UL_PAD_NAND_DATA01__RAWNAND_DATA01 0xb0b1
+ MX6UL_PAD_NAND_DATA02__RAWNAND_DATA02 0xb0b1
+ MX6UL_PAD_NAND_DATA03__RAWNAND_DATA03 0xb0b1
+ MX6UL_PAD_NAND_DATA04__RAWNAND_DATA04 0xb0b1
+ MX6UL_PAD_NAND_DATA05__RAWNAND_DATA05 0xb0b1
+ MX6UL_PAD_NAND_DATA06__RAWNAND_DATA06 0xb0b1
+ MX6UL_PAD_NAND_DATA07__RAWNAND_DATA07 0xb0b1
+ >;
+ };
+
+ pinctrl_uart3: uart3grp {
+ fsl,pins = <
+ MX6UL_PAD_UART3_TX_DATA__UART3_DCE_TX 0x1b0b1
+ MX6UL_PAD_UART3_RX_DATA__UART3_DCE_RX 0x1b099
+ MX6UL_PAD_UART3_RTS_B__UART3_DCE_RTS 0x1b0b1
+ MX6UL_PAD_UART3_CTS_B__UART3_DCE_CTS 0x1b099
+ MX6UL_PAD_GPIO1_IO01__GPIO1_IO01 0x79 /* BT_REG_ON */
+ MX6UL_PAD_SD1_CLK__GPIO2_IO17 0x100b1 /* BT_DEV_WAKE out */
+ MX6UL_PAD_ENET2_TX_EN__GPIO2_IO13 0x1b0b0 /* BT_HOST_WAKE in */
+ >;
+ };
+
+ pinctrl_uart4: uart4grp {
+ fsl,pins = <
+ MX6UL_PAD_UART4_TX_DATA__UART4_DCE_TX 0x1b0b1
+ MX6UL_PAD_UART4_RX_DATA__UART4_DCE_RX 0x1b0b1
+ >;
+ };
+
+ pinctrl_wlan: wlangrp {
+ fsl,pins = <
+ MX6UL_PAD_CSI_HSYNC__USDHC2_CMD 0x17059
+ MX6UL_PAD_CSI_VSYNC__USDHC2_CLK 0x10059
+ MX6UL_PAD_CSI_DATA00__USDHC2_DATA0 0x17059
+ MX6UL_PAD_CSI_DATA01__USDHC2_DATA1 0x17059
+ MX6UL_PAD_CSI_DATA02__USDHC2_DATA2 0x17059
+ MX6UL_PAD_CSI_DATA03__USDHC2_DATA3 0x17059
+ MX6UL_PAD_SD1_DATA3__GPIO2_IO21 0x79 /* WL_REG_ON */
+ MX6UL_PAD_UART2_CTS_B__GPIO1_IO22 0x100b1 /* WL_DEV_WAKE - WiFi_GPIO_4 - WiFi FW UART */
+ MX6UL_PAD_UART1_CTS_B__GPIO1_IO18 0x1b0b1 /* WL_HOST_WAKE - WIFI_GPIO_0 - OOB IRQ */
+ MX6UL_PAD_ENET1_RX_EN__OSC32K_32K_OUT 0x4001b031 /* OSC 32Khz wifi clk in */
+ >;
+ };
+};
select DM_THERMAL
imply CMD_DM
+config TARGET_MX6ULZ_SMM_M2
+ bool "Support imx6ulz_smm_m2"
+ depends on MX6ULL
+ select DM
+ select DM_GPIO
+ select DM_I2C
+ select DM_SERIAL
+ select DM_MTD
+ select DM_THERMAL
+ select SUPPORT_SPL
+
config TARGET_MYS_6ULX
bool "MYiR MYS-6ULX"
depends on MX6ULL
source "board/aristainetos/Kconfig"
source "board/armadeus/opos6uldev/Kconfig"
source "board/boundary/nitrogen6x/Kconfig"
+source "board/bsh/imx6ulz_smm_m2/Kconfig"
source "board/bticino/mamoj/Kconfig"
source "board/compulab/cm_fx6/Kconfig"
source "board/dhelectronics/dh_imx6/Kconfig"
--- /dev/null
+if TARGET_MX6ULZ_SMM_M2
+
+config SYS_BOARD
+ default "imx6ulz_smm_m2"
+
+config SYS_VENDOR
+ default "bsh"
+
+config SYS_CONFIG_NAME
+ default "imx6ulz_smm_m2"
+
+endif
--- /dev/null
+MX6ULZ_SMM_M2 BOARD
+M: Michael Trimarchi <michael@amarulasolutions.com>
+S: Maintained
+F: board/bsh/mx6ulz_smm_m2/
+F: include/configs/imx6ulz_smm_m2.h
+F: configs/imx6ulz_smm_m2_defconfig
--- /dev/null
+# SPDX-License-Identifier: GPL-2.0+
+# (C) Copyright 2021 Amarula Solutions B.V.
+
+obj-y := imx6ulz_smm_m2.o
+obj-$(CONFIG_SPL_BUILD) += spl.o
+
--- /dev/null
+How to Update U-Boot on imx6ulz_smm_m2 board
+--------------------------------------------
+
+Required software on the host PC:
+
+- UUU: https://github.com/NXPmicro/mfgtools
+
+Build U-Boot for m2:
+
+$ make mrproper
+$ make imx6ulz_smm_m2_defconfig
+$ make
+
+This generates the SPL and u-boot-dtb.img binaries.
+
+1. Loading U-Boot via USB Serial Download Protocol
+
+Copy SPL and u-boot-dtb.img to the uuu folder.
+
+Load the U-Boot via USB:
+
+$ sudo uuu -v -b nand_script.lst u-boot-with-spl.imx
+
+where nand_script.lst contains the following:
+
+uuu_version 1.2.39
+
+# @_flash.bin | bootloader
+# @_image [_flash.bin] | image burn to nand, default is the same as bootloader
+
+# This command will be run when i.MX6/7 i.MX8MM, i.MX8MQ
+SDP: boot -f _flash.bin
+
+# This command will be run when ROM support stream mode
+# i.MX8QXP, i.MX8QM
+SDPS: boot -f _flash.bin
+
+# These commands will be run when use SPL and will be skipped if no spl
+# SDPU will be deprecated. please use SDPV instead of SDPU
+# {
+SDPU: delay 1000
+SDPU: write -f _flash.bin -offset 0x57c00
+SDPU: jump
+# }
+
+# These commands will be run when use SPL and will be skipped if no spl
+# if (SPL support SDPV)
+# {
+SDPV: delay 1000
+SDPV: write -f _flash.bin -offset 0x11000
+SDPV: jump
+# }
+
+FB: ucmd setenv fastboot_buffer ${loadaddr}
+FB: download -f _image
+FB: ucmd if test ! -n "$fastboot_bytes"; then setenv fastboot_bytes $filesize; else true; fi
+# Burn image to nandfit partition if needed
+FB: ucmd if env exists nandfit_part; then nand erase.part nandfit; nand write ${fastboot_buffer} nandfit ${fastboot_bytes}; else true; fi;
+FB: ucmd nandbcb init ${fastboot_buffer} nandboot ${fastboot_bytes}
+FB: Done
+
+Then U-Boot starts and its messages appear in the console program.
+
+Use the default environment variables:
+
+=> env default -f -a
+=> saveenv
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ *
+ * Copyright (C) 2021 BSH Hausgeraete GmbH
+ */
+
+#include <init.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/iomux.h>
+#include <asm/arch/imx-regs.h>
+#include <asm/arch/crm_regs.h>
+#include <asm/arch/mx6-pins.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/mach-imx/boot_mode.h>
+#include <asm/global_data.h>
+#include <asm/gpio.h>
+#include <common.h>
+#include <env.h>
+#include <linux/sizes.h>
+
+static void setup_gpmi_nand(void)
+{
+ setup_gpmi_io_clk((MXC_CCM_CS2CDR_ENFC_CLK_PODF(0) |
+ MXC_CCM_CS2CDR_ENFC_CLK_PRED(3) |
+ MXC_CCM_CS2CDR_ENFC_CLK_SEL(3)));
+};
+
+int dram_init(void)
+{
+ gd->ram_size = imx_ddr_size();
+
+ return 0;
+}
+
+int board_init(void)
+{
+ /* Address of boot parameters */
+ gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
+
+ setup_gpmi_nand();
+
+ return 0;
+}
+
+int board_late_init(void)
+{
+ if (is_boot_from_usb()) {
+ env_set("bootcmd", "run bootcmd_mfg");
+ env_set("bootdelay", "0");
+ }
+
+ return 0;
+}
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0+
+
+#include <common.h>
+#include <cpu_func.h>
+#include <hang.h>
+#include <init.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/iomux.h>
+#include <asm/arch/imx-regs.h>
+#include <asm/arch/crm_regs.h>
+#include <asm/arch/mx6ull_pins.h>
+#include <asm/arch/mx6-pins.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/gpio.h>
+#include <asm/mach-imx/iomux-v3.h>
+#include <asm/mach-imx/boot_mode.h>
+#include <linux/libfdt.h>
+#include <spl.h>
+#include <asm/arch/mx6-ddr.h>
+
+#define UART_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
+ PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
+ PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS)
+
+static const iomux_v3_cfg_t uart4_pads[] = {
+ MX6_PAD_UART4_TX_DATA__UART4_DCE_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
+ MX6_PAD_UART4_RX_DATA__UART4_DCE_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+static void setup_iomux_uart(void)
+{
+ imx_iomux_v3_setup_multiple_pads(uart4_pads, ARRAY_SIZE(uart4_pads));
+}
+
+static struct mx6ul_iomux_grp_regs mx6_grp_ioregs = {
+ .grp_addds = 0x00000028,
+ .grp_ddrmode_ctl = 0x00020000,
+ .grp_b0ds = 0x00000028,
+ .grp_ctlds = 0x00000028,
+ .grp_b1ds = 0x00000028,
+ .grp_ddrpke = 0x00000000,
+ .grp_ddrmode = 0x00020000,
+ .grp_ddr_type = 0x000c0000,
+};
+
+static struct mx6ul_iomux_ddr_regs mx6_ddr_ioregs = {
+ .dram_dqm0 = 0x00000028,
+ .dram_dqm1 = 0x00000028,
+ .dram_ras = 0x00000028,
+ .dram_cas = 0x00000028,
+ .dram_odt0 = 0x00000028,
+ .dram_odt1 = 0x00000028,
+ .dram_sdba2 = 0x00000000,
+ .dram_sdclk_0 = 0x00000028,
+ .dram_sdqs0 = 0x00000028,
+ .dram_sdqs1 = 0x00000028,
+ .dram_reset = 0x000c0028,
+};
+
+static struct mx6_mmdc_calibration mx6_mmcd_calib = {
+ .p0_mpwldectrl0 = 0x00000000,
+ .p0_mpwldectrl1 = 0x00100010,
+ .p0_mpdgctrl0 = 0x414c014c,
+ .p0_mpdgctrl1 = 0x00000000,
+ .p0_mprddlctl = 0x40403a42,
+ .p0_mpwrdlctl = 0x4040342e,
+};
+
+static struct mx6_ddr_sysinfo ddr_sysinfo = {
+ .dsize = 0,
+ .cs1_mirror = 0,
+ .cs_density = 32,
+ .ncs = 1,
+ .bi_on = 1,
+ .rtt_nom = 1,
+ .rtt_wr = 0,
+ .ralat = 5,
+ .walat = 1,
+ .mif3_mode = 3,
+ .rst_to_cke = 0x23, /* 33 cycles (JEDEC value for DDR3) - total of 500 us */
+ .sde_to_rst = 0x10, /* 14 cycles (JEDEC value for DDR3) - total of 200 us */
+ .refsel = 1,
+ .refr = 3,
+};
+
+static struct mx6_ddr3_cfg mem_ddr = {
+ .mem_speed = 1333,
+ .density = 2,
+ .width = 16,
+ .banks = 8,
+ .rowaddr = 13,
+ .coladdr = 10,
+ .pagesz = 2,
+ .trcd = 1350,
+ .trcmin = 4950,
+ .trasmin = 3600,
+};
+
+static void ccgr_init(void)
+{
+ struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
+
+ writel(0xFFFFFFFF, &ccm->CCGR0);
+ writel(0xFFFFFFFF, &ccm->CCGR1);
+ writel(0xFFFFFFFF, &ccm->CCGR2);
+ writel(0xFFFFFFFF, &ccm->CCGR3);
+ writel(0xFFFFFFFF, &ccm->CCGR4);
+ writel(0xFFFFFFFF, &ccm->CCGR5);
+ writel(0xFFFFFFFF, &ccm->CCGR6);
+}
+
+static void imx6ul_spl_dram_cfg(void)
+{
+ mx6ul_dram_iocfg(mem_ddr.width, &mx6_ddr_ioregs, &mx6_grp_ioregs);
+ mx6_dram_cfg(&ddr_sysinfo, &mx6_mmcd_calib, &mem_ddr);
+}
+
+void board_init_f(ulong dummy)
+{
+ ccgr_init();
+ arch_cpu_init();
+ timer_init();
+ setup_iomux_uart();
+ preloader_console_init();
+ imx6ul_spl_dram_cfg();
+}
+
+void reset_cpu(void)
+{
+}
--- /dev/null
+CONFIG_ARM=y
+CONFIG_ARCH_MX6=y
+CONFIG_SYS_TEXT_BASE=0x87800000
+CONFIG_SYS_MALLOC_LEN=0x1000000
+CONFIG_SYS_MALLOC_F_LEN=0x18000
+CONFIG_SPL_GPIO=y
+CONFIG_SPL_LIBCOMMON_SUPPORT=y
+CONFIG_SPL_LIBGENERIC_SUPPORT=y
+CONFIG_NR_DRAM_BANKS=1
+CONFIG_ENV_SIZE=0x20000
+CONFIG_ENV_OFFSET=0x400000
+CONFIG_MX6ULL=y
+CONFIG_TARGET_MX6ULZ_SMM_M2=y
+CONFIG_DEFAULT_DEVICE_TREE="imx6ulz-bsh-smm-m2"
+CONFIG_SPL_TEXT_BASE=0x00908000
+CONFIG_SPL_SERIAL=y
+CONFIG_SPL=y
+CONFIG_DISTRO_DEFAULTS=y
+CONFIG_FIT=y
+CONFIG_FIT_SIGNATURE=y
+CONFIG_FIT_VERBOSE=y
+CONFIG_LEGACY_IMAGE_FORMAT=y
+CONFIG_BOOTDELAY=3
+CONFIG_BOARD_LATE_INIT=y
+CONFIG_SPL_BSS_START_ADDR=0x84100000
+CONFIG_SYS_SPL_MALLOC=y
+CONFIG_SPL_DMA=y
+CONFIG_SPL_MTD_SUPPORT=y
+CONFIG_SPL_NAND_SUPPORT=y
+CONFIG_SPL_USB_HOST=y
+CONFIG_SPL_USB_GADGET=y
+CONFIG_SPL_USB_SDP_SUPPORT=y
+CONFIG_SPL_WATCHDOG=y
+CONFIG_CMD_DM=y
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_USB=y
+CONFIG_CMD_USB_SDP=y
+CONFIG_CMD_CACHE=y
+CONFIG_CMD_MTDPARTS=y
+CONFIG_MTDIDS_DEFAULT="nand0=gpmi-nand"
+CONFIG_MTDPARTS_DEFAULT="mtdparts=gpmi-nand:4m(nandboot),1m(env),8m(kernel),1m(nanddtb),-(rootfs)"
+CONFIG_CMD_UBI=y
+# CONFIG_ISO_PARTITION is not set
+CONFIG_OF_CONTROL=y
+CONFIG_ENV_OVERWRITE=y
+CONFIG_ENV_IS_IN_NAND=y
+CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+# CONFIG_NET is not set
+CONFIG_BOUNCE_BUFFER=y
+CONFIG_USB_FUNCTION_FASTBOOT=y
+CONFIG_FASTBOOT_BUF_ADDR=0x82000000
+CONFIG_FASTBOOT_FLASH=y
+CONFIG_FASTBOOT_UUU_SUPPORT=y
+CONFIG_FASTBOOT_FLASH_NAND=y
+CONFIG_SYS_I2C_MXC=y
+# CONFIG_MMC is not set
+CONFIG_MTD=y
+CONFIG_MTD_RAW_NAND=y
+CONFIG_SYS_NAND_USE_FLASH_BBT=y
+CONFIG_NAND_MXS=y
+CONFIG_NAND_MXS_DT=y
+CONFIG_SYS_NAND_ONFI_DETECTION=y
+CONFIG_SYS_NAND_U_BOOT_LOCATIONS=y
+CONFIG_SYS_NAND_U_BOOT_OFFS=0x111400
+CONFIG_SYS_NAND_U_BOOT_OFFS_REDUND=0x291400
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_IMX6=y
+CONFIG_DM_PMIC=y
+CONFIG_DM_REGULATOR=y
+CONFIG_DM_REGULATOR_FIXED=y
+CONFIG_MXC_UART=y
+CONFIG_IMX_THERMAL=y
+CONFIG_USB=y
+CONFIG_USB_GADGET=y
+CONFIG_USB_GADGET_MANUFACTURER="BSH"
+CONFIG_USB_GADGET_VENDOR_NUM=0x0525
+CONFIG_USB_GADGET_PRODUCT_NUM=0xa4a5
+CONFIG_CI_UDC=y
+CONFIG_SDP_LOADADDR=0x877fffc0
--- /dev/null
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * Copyright (C) 2021 Amarula Solutions B.V.
+ *
+ */
+#ifndef __IMX6ULZ_SMM_M2_CONFIG_H
+#define __IMX6ULZ_SMM_M2_CONFIG_H
+
+#include "mx6_common.h"
+
+#include <asm/arch/imx-regs.h>
+#include <linux/sizes.h>
+#include <linux/stringify.h>
+
+/* SPL options */
+#include "imx6_spl.h"
+
+#define CONFIG_MXC_UART_BASE UART4_BASE
+
+#ifndef CONFIG_SPL_BUILD
+
+#define BOOT_TARGET_DEVICES(func) \
+ func(NAND, nand, 0) \
+
+#include <config_distro_bootcmd.h>
+
+#endif /* !CONFIG_SPL_BUILD */
+
+#define MEM_LAYOUT_ENV_SETTINGS \
+ "scriptaddr=" __stringify(CONFIG_SYS_LOAD_ADDR) "\0" \
+ "kernel_addr_r=" __stringify(CONFIG_SYS_LOAD_ADDR) "\0" \
+ "fdt_addr_r=0x81000000\0" \
+ "fdtfile=" CONFIG_DEFAULT_FDT_FILE "\0" \
+ "bootcmd_mfg=echo Running fastboot mode; fastboot usb 0\0" \
+
+#define NANDARGS \
+ "mtdids=" CONFIG_MTDIDS_DEFAULT "\0" \
+ CONFIG_MTDPARTS_DEFAULT "\0" \
+ "nandargs=setenv bootargs " \
+ "${optargs} " \
+ "mtdparts=${mtdparts} " \
+ "root=${nandroot} " \
+ "rootfstype=${nandrootfstype}\0" \
+ "nandroot=ubi0:root rw ubi.mtd=rootfs\0" \
+ "nandrootfstype=ubifs rootwait=1\0" \
+ "nandboot=echo Booting from nand ...; " \
+ "run nandargs; " \
+ "nand read ${fdt_addr_r} nanddtb; " \
+ "nand read ${loadaddr} kernel; " \
+ "bootz ${loadaddr} - ${fdt_addr_r}\0"
+
+#define BOOTENV_DEV_NAND(devtypeu, devtypel, instance) \
+ "bootcmd_" #devtypel #instance "=" \
+ "run nandboot\0"
+
+#define BOOTENV_DEV_NAME_NAND(devtypeu, devtypel, instance) \
+ #devtypel #instance " "
+
+/* Initial environment variables */
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ MEM_LAYOUT_ENV_SETTINGS \
+ NANDARGS \
+ BOOTENV
+
+/* Physical Memory Map */
+#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR
+#define PHYS_SDRAM_SIZE SZ_128M
+
+#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM
+#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR
+#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE
+
+/* NAND */
+#define CONFIG_SYS_MAX_NAND_DEVICE 1
+
+#define CONFIG_SYS_NAND_BASE 0x20000000
+
+#endif
projects / platform / kernel / u-boot.git / commitdiff