Synchronise device tree with linux v6.1-rc3.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
linux,autosuspend-period = <125>;
};
+ audio_codec_bt_sco: audio-codec-bt-sco {
+ compatible = "linux,bt-sco";
+ #sound-dai-cells = <1>;
+ };
+
wm8524: audio-codec {
#sound-dai-cells = <0>;
compatible = "wlf,wm8524";
wlf,mute-gpios = <&gpio1 8 GPIO_ACTIVE_LOW>;
};
+ sound-bt-sco {
+ compatible = "simple-audio-card";
+ simple-audio-card,name = "bt-sco-audio";
+ simple-audio-card,format = "dsp_a";
+ simple-audio-card,bitclock-inversion;
+ simple-audio-card,frame-master = <&btcpu>;
+ simple-audio-card,bitclock-master = <&btcpu>;
+
+ btcpu: simple-audio-card,cpu {
+ sound-dai = <&sai3>;
+ dai-tdm-slot-num = <2>;
+ dai-tdm-slot-width = <16>;
+ };
+
+ simple-audio-card,codec {
+ sound-dai = <&audio_codec_bt_sco 1>;
+ };
+ };
+
sound-wm8524 {
compatible = "simple-audio-card";
simple-audio-card,name = "wm8524-audio";
status = "okay";
};
+&sai3 {
+ #sound-dai-cells = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_sai3>;
+ assigned-clocks = <&clk IMX8MQ_CLK_SAI3>;
+ assigned-clock-parents = <&clk IMX8MQ_AUDIO_PLL1_OUT>;
+ assigned-clock-rates = <24576000>;
+ status = "okay";
+};
+
&snvs_pwrkey {
status = "okay";
};
>;
};
+ pinctrl_sai3: sai3grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_SAI3_TXFS_SAI3_TX_SYNC 0xd6
+ MX8MQ_IOMUXC_SAI3_TXC_SAI3_TX_BCLK 0xd6
+ MX8MQ_IOMUXC_SAI3_TXD_SAI3_TX_DATA0 0xd6
+ MX8MQ_IOMUXC_SAI3_RXD_SAI3_RX_DATA0 0xd6
+ >;
+ };
+
pinctrl_spdif1: spdif1grp {
fsl,pins = <
MX8MQ_IOMUXC_SPDIF_TX_SPDIF1_OUT 0xd6
--- /dev/null
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+// Copyright (C) 2021 Purism SPC <kernel@puri.sm>
+
+/dts-v1/;
+
+/*
+ * This file describes hardware that is shared among r3 ("Dogwood") and
+ * later revisions of the Librem 5 so it has to be included in dts there.
+ */
+
+#include "imx8mq-librem5.dtsi"
+
+/ {
+ model = "Purism Librem 5r3";
+ compatible = "purism,librem5r3", "purism,librem5", "fsl,imx8mq";
+};
+
+&accel_gyro {
+ mount-matrix = "1", "0", "0",
+ "0", "1", "0",
+ "0", "0", "-1";
+};
+
+&bq25895 {
+ ti,battery-regulation-voltage = <4200000>; /* uV */
+ ti,charge-current = <1500000>; /* uA */
+ ti,termination-current = <144000>; /* uA */
+};
+
+&camera_front {
+ pinctrl-0 = <&pinctrl_csi1>, <&pinctrl_r3_camera_pwr>;
+ shutdown-gpios = <&gpio5 4 GPIO_ACTIVE_LOW>;
+};
+
+&iomuxc {
+ pinctrl_r3_camera_pwr: r3camerapwrgrp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_SPDIF_RX_GPIO5_IO4 0x83
+ >;
+ };
+};
+
+&proximity {
+ proximity-near-level = <25>;
+};
// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
-// Copyright (C) 2020 Purism SPC <kernel@puri.sm>
+// Copyright (C) 2021 Purism SPC <kernel@puri.sm>
/dts-v1/;
-#include "imx8mq-librem5.dtsi"
+#include "imx8mq-librem5-r3.dtsi"
/ {
model = "Purism Librem 5r4";
compatible = "purism,librem5r4", "purism,librem5", "fsl,imx8mq";
};
-&accel_gyro {
- mount-matrix = "1", "0", "0",
- "0", "1", "0",
- "0", "0", "-1";
-};
-
&bat {
maxim,rsns-microohm = <1667>;
};
-&bq25895 {
- ti,battery-regulation-voltage = <4200000>; /* uV */
- ti,charge-current = <1500000>; /* uA */
- ti,termination-current = <144000>; /* uA */
-};
-
&led_backlight {
led-max-microamp = <25000>;
};
+&lcd_panel {
+ compatible = "ys,ys57pss36bh5gq";
+};
+
&proximity {
proximity-near-level = <10>;
};
#include "dt-bindings/input/input.h"
#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/leds/common.h>
#include "dt-bindings/pwm/pwm.h"
#include "dt-bindings/usb/pd.h"
#include "imx8mq.dtsi"
/ {
model = "Purism Librem 5";
compatible = "purism,librem5", "fsl,imx8mq";
+ chassis-type = "handset";
backlight_dsi: backlight-dsi {
compatible = "led-backlight";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_keys>;
- vol-down {
+ key-vol-down {
label = "VOL_DOWN";
gpios = <&gpio1 17 GPIO_ACTIVE_LOW>;
linux,code = <KEY_VOLUMEDOWN>;
debounce-interval = <50>;
+ wakeup-source;
};
- vol-up {
+ key-vol-up {
label = "VOL_UP";
gpios = <&gpio1 16 GPIO_ACTIVE_LOW>;
linux,code = <KEY_VOLUMEUP>;
debounce-interval = <50>;
+ wakeup-source;
+ };
+ };
+
+ led-controller {
+ compatible = "pwm-leds";
+
+ led-0 {
+ function = LED_FUNCTION_STATUS;
+ color = <LED_COLOR_ID_BLUE>;
+ max-brightness = <248>;
+ pwms = <&pwm2 0 50000 0>;
+ };
+
+ led-1 {
+ function = LED_FUNCTION_STATUS;
+ color = <LED_COLOR_ID_GREEN>;
+ max-brightness = <248>;
+ pwms = <&pwm4 0 50000 0>;
+ };
+
+ led-2 {
+ function = LED_FUNCTION_STATUS;
+ color = <LED_COLOR_ID_RED>;
+ max-brightness = <248>;
+ pwms = <&pwm3 0 50000 0>;
};
};
enable-active-high;
};
+ /*
+ * the pinctrl for reg_csi_1v8 and reg_vcam_1v8 is added to the PMIC
+ * since we can't have it twice in the 2 different regulator nodes.
+ */
+ reg_csi_1v8: regulator-csi-1v8 {
+ compatible = "regulator-fixed";
+ regulator-name = "CAMERA_VDDIO_1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ vin-supply = <®_vdd_3v3>;
+ gpio = <&gpio1 0 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ /* controlled by the CAMERA_POWER_KEY HKS */
+ reg_vcam_1v2: regulator-vcam-1v2 {
+ compatible = "regulator-fixed";
+ regulator-name = "CAMERA_VDDD_1V2";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ vin-supply = <®_vdd_1v8>;
+ enable-active-high;
+ };
+
+ reg_vcam_2v8: regulator-vcam-2v8 {
+ compatible = "regulator-fixed";
+ regulator-name = "CAMERA_VDDA_2V8";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ vin-supply = <®_vdd_3v3>;
+ gpio = <&gpio1 0 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
reg_gnss: regulator-gnss {
compatible = "regulator-fixed";
pinctrl-names = "default";
cpu-supply = <&buck2_reg>;
};
+&csi1 {
+ status = "okay";
+};
+
&ddrc {
operating-points-v2 = <&ddrc_opp_table>;
+ status = "okay";
ddrc_opp_table: opp-table {
compatible = "operating-points-v2";
};
partition@30000 {
- label = "protected1";
- reg = <0x30000 0x10000>;
+ label = "firmware";
+ reg = <0x30000 0x1d0000>;
read-only;
};
-
- partition@40000 {
- label = "rw";
- reg = <0x40000 0x1C0000>;
- };
};
};
>;
};
+ pinctrl_camera_pwr: camerapwrgrp {
+ fsl,pins = <
+ /* CAMERA_PWR_EN_3V3 */
+ MX8MQ_IOMUXC_GPIO1_IO00_GPIO1_IO0 0x83
+ >;
+ };
+
+ pinctrl_csi1: csi1grp {
+ fsl,pins = <
+ /* CSI1_NRST */
+ MX8MQ_IOMUXC_ENET_RXC_GPIO1_IO25 0x83
+ >;
+ };
+
pinctrl_charger_in: chargeringrp {
fsl,pins = <
/* CHRG_INT */
MX8MQ_IOMUXC_NAND_CE2_B_GPIO3_IO3 0x80
- /* CHG_STATUS_B */
- MX8MQ_IOMUXC_NAND_ALE_GPIO3_IO0 0x80
>;
};
interrupt-names = "irq";
connector {
+ compatible = "usb-c-connector";
+ label = "USB-C";
+ data-role = "dual";
+
ports {
#address-cells = <1>;
#size-cells = <0>;
compatible = "rohm,bd71837";
reg = <0x4b>;
pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_pmic>;
+ pinctrl-0 = <&pinctrl_pmic>, <&pinctrl_camera_pwr>;
clocks = <&pmic_osc>;
clock-names = "osc";
clock-output-names = "pmic_clk";
>;
};
+ camera_front: camera@20 {
+ compatible = "hynix,hi846";
+ reg = <0x20>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_csi1>;
+ clocks = <&clk IMX8MQ_CLK_CLKO2>;
+ assigned-clocks = <&clk IMX8MQ_CLK_CLKO2>;
+ assigned-clock-rates = <25000000>;
+ reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
+ vdda-supply = <®_vcam_2v8>;
+ vddd-supply = <®_vcam_1v2>;
+ vddio-supply = <®_csi_1v8>;
+ rotation = <90>;
+ orientation = <0>;
+
+ port {
+ camera1_ep: endpoint {
+ data-lanes = <1 2>;
+ link-frequencies = /bits/ 64
+ <80000000 200000000 300000000>;
+ remote-endpoint = <&mipi1_sensor_ep>;
+ };
+ };
+ };
+
backlight@36 {
compatible = "ti,lm36922";
reg = <0x36>;
pinctrl-0 = <&pinctrl_i2c4>;
status = "okay";
+ vcm@c {
+ compatible = "dongwoon,dw9714";
+ reg = <0x0c>;
+ vcc-supply = <®_csi_1v8>;
+ };
+
bat: fuel-gauge@36 {
compatible = "maxim,max17055";
reg = <0x36>;
interrupts = <20 IRQ_TYPE_LEVEL_LOW>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_gauge>;
+ power-supplies = <&bq25895>;
maxim,over-heat-temp = <700>;
maxim,over-volt = <4500>;
maxim,rsns-microohm = <5000>;
ti,precharge-current = <130000>; /* uA */
ti,minimum-sys-voltage = <3700000>; /* uV */
ti,boost-voltage = <5000000>; /* uV */
- ti,boost-max-current = <500000>; /* uA */
+ ti,boost-max-current = <1500000>; /* uA */
ti,use-vinmin-threshold = <1>; /* enable VINDPM */
ti,vinmin-threshold = <3900000>; /* uV */
monitored-battery = <&bat>;
status = "okay";
};
+&mipi_csi1 {
+ status = "okay";
+
+ ports {
+ port@0 {
+ reg = <0>;
+
+ mipi1_sensor_ep: endpoint {
+ remote-endpoint = <&camera1_ep>;
+ data-lanes = <1 2>;
+ };
+ };
+ };
+};
+
&mipi_dsi {
#address-cells = <1>;
#size-cells = <0>;
#size-cells = <0>;
dr_mode = "otg";
snps,dis_u3_susphy_quirk;
+ usb-role-switch;
status = "okay";
port@0 {
};
-&{/soc@0} {
+&soc {
u-boot,dm-spl;
};
-&{/soc@0/bus@30000000} {
+&aips1 {
u-boot,dm-spl;
};
-&{/soc@0/bus@30400000} {
+&aips2 {
u-boot,dm-spl;
};
-&{/soc@0/bus@30800000} {
+&aips3 {
u-boot,dm-spl;
};
-&{/soc@0/bus@32c00000} {
+&aips4 {
u-boot,dm-spl;
};
clk_ext4: clock-ext4 {
compatible = "fixed-clock";
#clock-cells = <0>;
- clock-frequency= <133000000>;
+ clock-frequency = <133000000>;
clock-output-names = "clk_ext4";
};
arm,no-tick-in-suspend;
};
- soc@0 {
+ soc: soc@0 {
compatible = "fsl,imx8mq-soc", "simple-bus";
#address-cells = <1>;
#size-cells = <1>;
nvmem-cells = <&imx8mq_uid>;
nvmem-cell-names = "soc_unique_id";
- bus@30000000 { /* AIPS1 */
+ aips1: bus@30000000 { /* AIPS1 */
compatible = "fsl,aips-bus", "simple-bus";
reg = <0x30000000 0x400000>;
#address-cells = <1>;
<0x00030005 0x00000053>,
<0x00030006 0x0000005f>,
<0x00030007 0x00000071>;
- #thermal-sensor-cells = <1>;
+ #thermal-sensor-cells = <1>;
};
wdog1: watchdog@30280000 {
status = "disabled";
};
- sdma2: sdma@302c0000 {
+ sdma2: dma-controller@302c0000 {
compatible = "fsl,imx8mq-sdma","fsl,imx7d-sdma";
reg = <0x302c0000 0x10000>;
interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>;
};
};
- bus@30400000 { /* AIPS2 */
+ aips2: bus@30400000 { /* AIPS2 */
compatible = "fsl,aips-bus", "simple-bus";
reg = <0x30400000 0x400000>;
#address-cells = <1>;
};
};
- bus@30800000 { /* AIPS3 */
+ aips3: bus@30800000 { /* AIPS3 */
compatible = "fsl,aips-bus", "simple-bus";
reg = <0x30800000 0x400000>;
#address-cells = <1>;
compatible = "fsl,sec-v4.0-job-ring";
reg = <0x1000 0x1000>;
interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
};
sec_jr1: jr@2000 {
status = "disabled";
};
- sdma1: sdma@30bd0000 {
+ sdma1: dma-controller@30bd0000 {
compatible = "fsl,imx8mq-sdma","fsl,imx7d-sdma";
reg = <0x30bd0000 0x10000>;
interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
};
};
- bus@32c00000 { /* AIPS4 */
+ aips4: bus@32c00000 { /* AIPS4 */
compatible = "fsl,aips-bus", "simple-bus";
reg = <0x32c00000 0x400000>;
#address-cells = <1>;
#define IMX8MQ_RESET_A53_L2RESET 17
#define IMX8MQ_RESET_SW_NON_SCLR_M4C_RST 18
#define IMX8MQ_RESET_OTG1_PHY_RESET 19
-#define IMX8MQ_RESET_OTG2_PHY_RESET 20
-#define IMX8MQ_RESET_MIPI_DSI_RESET_BYTE_N 21
-#define IMX8MQ_RESET_MIPI_DSI_RESET_N 22
-#define IMX8MQ_RESET_MIPI_DSI_DPI_RESET_N 23
-#define IMX8MQ_RESET_MIPI_DSI_ESC_RESET_N 24
-#define IMX8MQ_RESET_MIPI_DSI_PCLK_RESET_N 25
-#define IMX8MQ_RESET_PCIEPHY 26
-#define IMX8MQ_RESET_PCIEPHY_PERST 27
-#define IMX8MQ_RESET_PCIE_CTRL_APPS_EN 28
-#define IMX8MQ_RESET_PCIE_CTRL_APPS_TURNOFF 29
-#define IMX8MQ_RESET_HDMI_PHY_APB_RESET 30 /* i.MX8MM does NOT support */
+#define IMX8MQ_RESET_OTG2_PHY_RESET 20 /* i.MX8MN does NOT support */
+#define IMX8MQ_RESET_MIPI_DSI_RESET_BYTE_N 21 /* i.MX8MN does NOT support */
+#define IMX8MQ_RESET_MIPI_DSI_RESET_N 22 /* i.MX8MN does NOT support */
+#define IMX8MQ_RESET_MIPI_DSI_DPI_RESET_N 23 /* i.MX8MN does NOT support */
+#define IMX8MQ_RESET_MIPI_DSI_ESC_RESET_N 24 /* i.MX8MN does NOT support */
+#define IMX8MQ_RESET_MIPI_DSI_PCLK_RESET_N 25 /* i.MX8MN does NOT support */
+#define IMX8MQ_RESET_PCIEPHY 26 /* i.MX8MN does NOT support */
+#define IMX8MQ_RESET_PCIEPHY_PERST 27 /* i.MX8MN does NOT support */
+#define IMX8MQ_RESET_PCIE_CTRL_APPS_EN 28 /* i.MX8MN does NOT support */
+#define IMX8MQ_RESET_PCIE_CTRL_APPS_TURNOFF 29 /* i.MX8MN does NOT support */
+#define IMX8MQ_RESET_HDMI_PHY_APB_RESET 30 /* i.MX8MM/i.MX8MN does NOT support */
#define IMX8MQ_RESET_DISP_RESET 31
#define IMX8MQ_RESET_GPU_RESET 32
-#define IMX8MQ_RESET_VPU_RESET 33
-#define IMX8MQ_RESET_PCIEPHY2 34 /* i.MX8MM does NOT support */
-#define IMX8MQ_RESET_PCIEPHY2_PERST 35 /* i.MX8MM does NOT support */
-#define IMX8MQ_RESET_PCIE2_CTRL_APPS_EN 36 /* i.MX8MM does NOT support */
-#define IMX8MQ_RESET_PCIE2_CTRL_APPS_TURNOFF 37 /* i.MX8MM does NOT support */
-#define IMX8MQ_RESET_MIPI_CSI1_CORE_RESET 38 /* i.MX8MM does NOT support */
-#define IMX8MQ_RESET_MIPI_CSI1_PHY_REF_RESET 39 /* i.MX8MM does NOT support */
-#define IMX8MQ_RESET_MIPI_CSI1_ESC_RESET 40 /* i.MX8MM does NOT support */
-#define IMX8MQ_RESET_MIPI_CSI2_CORE_RESET 41 /* i.MX8MM does NOT support */
-#define IMX8MQ_RESET_MIPI_CSI2_PHY_REF_RESET 42 /* i.MX8MM does NOT support */
-#define IMX8MQ_RESET_MIPI_CSI2_ESC_RESET 43 /* i.MX8MM does NOT support */
-#define IMX8MQ_RESET_DDRC1_PRST 44
-#define IMX8MQ_RESET_DDRC1_CORE_RESET 45
-#define IMX8MQ_RESET_DDRC1_PHY_RESET 46
-#define IMX8MQ_RESET_DDRC2_PRST 47 /* i.MX8MM does NOT support */
-#define IMX8MQ_RESET_DDRC2_CORE_RESET 48 /* i.MX8MM does NOT support */
-#define IMX8MQ_RESET_DDRC2_PHY_RESET 49 /* i.MX8MM does NOT support */
+#define IMX8MQ_RESET_VPU_RESET 33 /* i.MX8MN does NOT support */
+#define IMX8MQ_RESET_PCIEPHY2 34 /* i.MX8MM/i.MX8MN does NOT support */
+#define IMX8MQ_RESET_PCIEPHY2_PERST 35 /* i.MX8MM/i.MX8MN does NOT support */
+#define IMX8MQ_RESET_PCIE2_CTRL_APPS_EN 36 /* i.MX8MM/i.MX8MN does NOT support */
+#define IMX8MQ_RESET_PCIE2_CTRL_APPS_TURNOFF 37 /* i.MX8MM/i.MX8MN does NOT support */
+#define IMX8MQ_RESET_MIPI_CSI1_CORE_RESET 38 /* i.MX8MM/i.MX8MN does NOT support */
+#define IMX8MQ_RESET_MIPI_CSI1_PHY_REF_RESET 39 /* i.MX8MM/i.MX8MN does NOT support */
+#define IMX8MQ_RESET_MIPI_CSI1_ESC_RESET 40 /* i.MX8MM/i.MX8MN does NOT support */
+#define IMX8MQ_RESET_MIPI_CSI2_CORE_RESET 41 /* i.MX8MM/i.MX8MN does NOT support */
+#define IMX8MQ_RESET_MIPI_CSI2_PHY_REF_RESET 42 /* i.MX8MM/i.MX8MN does NOT support */
+#define IMX8MQ_RESET_MIPI_CSI2_ESC_RESET 43 /* i.MX8MM/i.MX8MN does NOT support */
+#define IMX8MQ_RESET_DDRC1_PRST 44 /* i.MX8MN does NOT support */
+#define IMX8MQ_RESET_DDRC1_CORE_RESET 45 /* i.MX8MN does NOT support */
+#define IMX8MQ_RESET_DDRC1_PHY_RESET 46 /* i.MX8MN does NOT support */
+#define IMX8MQ_RESET_DDRC2_PRST 47 /* i.MX8MM/i.MX8MN does NOT support */
+#define IMX8MQ_RESET_DDRC2_CORE_RESET 48 /* i.MX8MM/i.MX8MN does NOT support */
+#define IMX8MQ_RESET_DDRC2_PHY_RESET 49 /* i.MX8MM/i.MX8MN does NOT support */
+#define IMX8MQ_RESET_SW_M4C_RST 50
+#define IMX8MQ_RESET_SW_M4P_RST 51
+#define IMX8MQ_RESET_M4_ENABLE 52
-#define IMX8MQ_RESET_NUM 50
+#define IMX8MQ_RESET_NUM 53
#endif
projects / platform / kernel / u-boot.git / commitdiff