--- /dev/null
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (c) 2020 Linaro Limited
+ *
+ * Based on original driver:
+ * Copyright (c) 2012-2020, The Linux Foundation. All rights reserved.
+ */
+#include <linux/bitfield.h>
+#include <linux/iio/adc/qcom-vadc-common.h>
+#include <linux/iio/consumer.h>
+#include <linux/interrupt.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/thermal.h>
+
+/*
+ * Thermal monitoring block consists of 8 (ADC_TM5_NUM_CHANNELS) channels. Each
+ * channel is programmed to use one of ADC channels for voltage comparison.
+ * Voltages are programmed using ADC codes, so we have to convert temp to
+ * voltage and then to ADC code value.
+ *
+ * Configuration of TM channels must match configuration of corresponding ADC
+ * channels.
+ */
+
+#define ADC5_MAX_CHANNEL 0xc0
+#define ADC_TM5_NUM_CHANNELS 8
+
+#define ADC_TM5_STATUS_LOW 0x0a
+
+#define ADC_TM5_STATUS_HIGH 0x0b
+
+#define ADC_TM5_NUM_BTM 0x0f
+
+#define ADC_TM5_ADC_DIG_PARAM 0x42
+
+#define ADC_TM5_FAST_AVG_CTL (ADC_TM5_ADC_DIG_PARAM + 1)
+#define ADC_TM5_FAST_AVG_EN BIT(7)
+
+#define ADC_TM5_MEAS_INTERVAL_CTL (ADC_TM5_ADC_DIG_PARAM + 2)
+#define ADC_TM5_TIMER1 3 /* 3.9ms */
+
+#define ADC_TM5_MEAS_INTERVAL_CTL2 (ADC_TM5_ADC_DIG_PARAM + 3)
+#define ADC_TM5_MEAS_INTERVAL_CTL2_MASK 0xf0
+#define ADC_TM5_TIMER2 10 /* 1 second */
+#define ADC_TM5_MEAS_INTERVAL_CTL3_MASK 0xf
+#define ADC_TM5_TIMER3 4 /* 4 second */
+
+#define ADC_TM_EN_CTL1 0x46
+#define ADC_TM_EN BIT(7)
+#define ADC_TM_CONV_REQ 0x47
+#define ADC_TM_CONV_REQ_EN BIT(7)
+
+#define ADC_TM5_M_CHAN_BASE 0x60
+
+#define ADC_TM5_M_ADC_CH_SEL_CTL(n) (ADC_TM5_M_CHAN_BASE + ((n) * 8) + 0)
+#define ADC_TM5_M_LOW_THR0(n) (ADC_TM5_M_CHAN_BASE + ((n) * 8) + 1)
+#define ADC_TM5_M_LOW_THR1(n) (ADC_TM5_M_CHAN_BASE + ((n) * 8) + 2)
+#define ADC_TM5_M_HIGH_THR0(n) (ADC_TM5_M_CHAN_BASE + ((n) * 8) + 3)
+#define ADC_TM5_M_HIGH_THR1(n) (ADC_TM5_M_CHAN_BASE + ((n) * 8) + 4)
+#define ADC_TM5_M_MEAS_INTERVAL_CTL(n) (ADC_TM5_M_CHAN_BASE + ((n) * 8) + 5)
+#define ADC_TM5_M_CTL(n) (ADC_TM5_M_CHAN_BASE + ((n) * 8) + 6)
+#define ADC_TM5_M_CTL_HW_SETTLE_DELAY_MASK 0xf
+#define ADC_TM5_M_CTL_CAL_SEL_MASK 0x30
+#define ADC_TM5_M_CTL_CAL_VAL 0x40
+#define ADC_TM5_M_EN(n) (ADC_TM5_M_CHAN_BASE + ((n) * 8) + 7)
+#define ADC_TM5_M_MEAS_EN BIT(7)
+#define ADC_TM5_M_HIGH_THR_INT_EN BIT(1)
+#define ADC_TM5_M_LOW_THR_INT_EN BIT(0)
+
+enum adc5_timer_select {
+ ADC5_TIMER_SEL_1 = 0,
+ ADC5_TIMER_SEL_2,
+ ADC5_TIMER_SEL_3,
+ ADC5_TIMER_SEL_NONE,
+};
+
+struct adc_tm5_data {
+ const u32 full_scale_code_volt;
+ unsigned int *decimation;
+ unsigned int *hw_settle;
+};
+
+enum adc_tm5_cal_method {
+ ADC_TM5_NO_CAL = 0,
+ ADC_TM5_RATIOMETRIC_CAL,
+ ADC_TM5_ABSOLUTE_CAL
+};
+
+struct adc_tm5_chip;
+
+/**
+ * struct adc_tm5_channel - ADC Thermal Monitoring channel data.
+ * @channel: channel number.
+ * @adc_channel: corresponding ADC channel number.
+ * @cal_method: calibration method.
+ * @prescale: channel scaling performed on the input signal.
+ * @hw_settle_time: the time between AMUX being configured and the
+ * start of conversion.
+ * @iio: IIO channel instance used by this channel.
+ * @chip: ADC TM chip instance.
+ * @tzd: thermal zone device used by this channel.
+ */
+struct adc_tm5_channel {
+ unsigned int channel;
+ unsigned int adc_channel;
+ enum adc_tm5_cal_method cal_method;
+ unsigned int prescale;
+ unsigned int hw_settle_time;
+ struct iio_channel *iio;
+ struct adc_tm5_chip *chip;
+ struct thermal_zone_device *tzd;
+};
+
+/**
+ * struct adc_tm5_chip - ADC Thermal Monitoring properties
+ * @regmap: SPMI ADC5 Thermal Monitoring peripheral register map field.
+ * @dev: SPMI ADC5 device.
+ * @data: software configuration data.
+ * @channels: array of ADC TM channel data.
+ * @nchannels: amount of channels defined/allocated
+ * @decimation: sampling rate supported for the channel.
+ * @avg_samples: ability to provide single result from the ADC
+ * that is an average of multiple measurements.
+ * @base: base address of TM registers.
+ */
+struct adc_tm5_chip {
+ struct regmap *regmap;
+ struct device *dev;
+ const struct adc_tm5_data *data;
+ struct adc_tm5_channel *channels;
+ unsigned int nchannels;
+ unsigned int decimation;
+ unsigned int avg_samples;
+ u16 base;
+};
+
+static const struct adc_tm5_data adc_tm5_data_pmic = {
+ .full_scale_code_volt = 0x70e4,
+ .decimation = (unsigned int []) { 250, 420, 840 },
+ .hw_settle = (unsigned int []) { 15, 100, 200, 300, 400, 500, 600, 700,
+ 1000, 2000, 4000, 8000, 16000, 32000,
+ 64000, 128000 },
+};
+
+static int adc_tm5_read(struct adc_tm5_chip *adc_tm, u16 offset, u8 *data, int len)
+{
+ return regmap_bulk_read(adc_tm->regmap, adc_tm->base + offset, data, len);
+}
+
+static int adc_tm5_write(struct adc_tm5_chip *adc_tm, u16 offset, u8 *data, int len)
+{
+ return regmap_bulk_write(adc_tm->regmap, adc_tm->base + offset, data, len);
+}
+
+static int adc_tm5_reg_update(struct adc_tm5_chip *adc_tm, u16 offset, u8 mask, u8 val)
+{
+ return regmap_write_bits(adc_tm->regmap, adc_tm->base + offset, mask, val);
+}
+
+static irqreturn_t adc_tm5_isr(int irq, void *data)
+{
+ struct adc_tm5_chip *chip = data;
+ u8 status_low, status_high, ctl;
+ int ret, i;
+
+ ret = adc_tm5_read(chip, ADC_TM5_STATUS_LOW, &status_low, sizeof(status_low));
+ if (unlikely(ret)) {
+ dev_err(chip->dev, "read status low failed: %d\n", ret);
+ return IRQ_HANDLED;
+ }
+
+ ret = adc_tm5_read(chip, ADC_TM5_STATUS_HIGH, &status_high, sizeof(status_high));
+ if (unlikely(ret)) {
+ dev_err(chip->dev, "read status high failed: %d\n", ret);
+ return IRQ_HANDLED;
+ }
+
+ for (i = 0; i < chip->nchannels; i++) {
+ bool upper_set = false, lower_set = false;
+ unsigned int ch = chip->channels[i].channel;
+
+ /* No TZD, we warned at the boot time */
+ if (!chip->channels[i].tzd)
+ continue;
+
+ ret = adc_tm5_read(chip, ADC_TM5_M_EN(ch), &ctl, sizeof(ctl));
+ if (unlikely(ret)) {
+ dev_err(chip->dev, "ctl read failed: %d, channel %d\n", ret, i);
+ continue;
+ }
+
+ if (!(ctl & ADC_TM5_M_MEAS_EN))
+ continue;
+
+ lower_set = (status_low & BIT(ch)) &&
+ (ctl & ADC_TM5_M_LOW_THR_INT_EN);
+
+ upper_set = (status_high & BIT(ch)) &&
+ (ctl & ADC_TM5_M_HIGH_THR_INT_EN);
+
+ if (upper_set || lower_set)
+ thermal_zone_device_update(chip->channels[i].tzd,
+ THERMAL_EVENT_UNSPECIFIED);
+ }
+
+ return IRQ_HANDLED;
+}
+
+static int adc_tm5_get_temp(void *data, int *temp)
+{
+ struct adc_tm5_channel *channel = data;
+ int ret;
+
+ if (!channel || !channel->iio)
+ return -EINVAL;
+
+ ret = iio_read_channel_processed(channel->iio, temp);
+ if (ret < 0)
+ return ret;
+
+ if (ret != IIO_VAL_INT)
+ return -EINVAL;
+
+ return 0;
+}
+
+static int adc_tm5_disable_channel(struct adc_tm5_channel *channel)
+{
+ struct adc_tm5_chip *chip = channel->chip;
+ unsigned int reg = ADC_TM5_M_EN(channel->channel);
+
+ return adc_tm5_reg_update(chip, reg,
+ ADC_TM5_M_MEAS_EN |
+ ADC_TM5_M_HIGH_THR_INT_EN |
+ ADC_TM5_M_LOW_THR_INT_EN,
+ 0);
+}
+
+static int adc_tm5_enable(struct adc_tm5_chip *chip)
+{
+ int ret;
+ u8 data;
+
+ data = ADC_TM_EN;
+ ret = adc_tm5_write(chip, ADC_TM_EN_CTL1, &data, sizeof(data));
+ if (ret < 0) {
+ dev_err(chip->dev, "adc-tm enable failed\n");
+ return ret;
+ }
+
+ data = ADC_TM_CONV_REQ_EN;
+ ret = adc_tm5_write(chip, ADC_TM_CONV_REQ, &data, sizeof(data));
+ if (ret < 0) {
+ dev_err(chip->dev, "adc-tm request conversion failed\n");
+ return ret;
+ }
+
+ return 0;
+}
+
+static int adc_tm5_configure(struct adc_tm5_channel *channel, int low, int high)
+{
+ struct adc_tm5_chip *chip = channel->chip;
+ u8 buf[8];
+ u16 reg = ADC_TM5_M_ADC_CH_SEL_CTL(channel->channel);
+ int ret;
+
+ ret = adc_tm5_read(chip, reg, buf, sizeof(buf));
+ if (ret) {
+ dev_err(chip->dev, "channel %d params read failed: %d\n", channel->channel, ret);
+ return ret;
+ }
+
+ buf[0] = channel->adc_channel;
+
+ /* High temperature corresponds to low voltage threshold */
+ if (high != INT_MAX) {
+ u16 adc_code = qcom_adc_tm5_temp_volt_scale(channel->prescale,
+ chip->data->full_scale_code_volt, high);
+
+ buf[1] = adc_code & 0xff;
+ buf[2] = adc_code >> 8;
+ buf[7] |= ADC_TM5_M_LOW_THR_INT_EN;
+ } else {
+ buf[7] &= ~ADC_TM5_M_LOW_THR_INT_EN;
+ }
+
+ /* Low temperature corresponds to high voltage threshold */
+ if (low != -INT_MAX) {
+ u16 adc_code = qcom_adc_tm5_temp_volt_scale(channel->prescale,
+ chip->data->full_scale_code_volt, low);
+
+ buf[3] = adc_code & 0xff;
+ buf[4] = adc_code >> 8;
+ buf[7] |= ADC_TM5_M_HIGH_THR_INT_EN;
+ } else {
+ buf[7] &= ~ADC_TM5_M_HIGH_THR_INT_EN;
+ }
+
+ buf[5] = ADC5_TIMER_SEL_2;
+
+ /* Set calibration select, hw_settle delay */
+ buf[6] &= ~ADC_TM5_M_CTL_HW_SETTLE_DELAY_MASK;
+ buf[6] |= FIELD_PREP(ADC_TM5_M_CTL_HW_SETTLE_DELAY_MASK, channel->hw_settle_time);
+ buf[6] &= ~ADC_TM5_M_CTL_CAL_SEL_MASK;
+ buf[6] |= FIELD_PREP(ADC_TM5_M_CTL_CAL_SEL_MASK, channel->cal_method);
+
+ buf[7] |= ADC_TM5_M_MEAS_EN;
+
+ ret = adc_tm5_write(chip, reg, buf, sizeof(buf));
+ if (ret) {
+ dev_err(chip->dev, "channel %d params write failed: %d\n", channel->channel, ret);
+ return ret;
+ }
+
+ return adc_tm5_enable(chip);
+}
+
+static int adc_tm5_set_trips(void *data, int low, int high)
+{
+ struct adc_tm5_channel *channel = data;
+ struct adc_tm5_chip *chip;
+ int ret;
+
+ if (!channel)
+ return -EINVAL;
+
+ chip = channel->chip;
+ dev_dbg(chip->dev, "%d:low(mdegC):%d, high(mdegC):%d\n",
+ channel->channel, low, high);
+
+ if (high == INT_MAX && low <= -INT_MAX)
+ ret = adc_tm5_disable_channel(channel);
+ else
+ ret = adc_tm5_configure(channel, low, high);
+
+ return ret;
+}
+
+static struct thermal_zone_of_device_ops adc_tm5_ops = {
+ .get_temp = adc_tm5_get_temp,
+ .set_trips = adc_tm5_set_trips,
+};
+
+static int adc_tm5_register_tzd(struct adc_tm5_chip *adc_tm)
+{
+ unsigned int i;
+ struct thermal_zone_device *tzd;
+
+ for (i = 0; i < adc_tm->nchannels; i++) {
+ adc_tm->channels[i].chip = adc_tm;
+
+ tzd = devm_thermal_zone_of_sensor_register(adc_tm->dev,
+ adc_tm->channels[i].channel,
+ &adc_tm->channels[i],
+ &adc_tm5_ops);
+ if (IS_ERR(tzd)) {
+ dev_err(adc_tm->dev, "Error registering TZ zone for channel %d: %ld\n",
+ adc_tm->channels[i].channel, PTR_ERR(tzd));
+ return PTR_ERR(tzd);
+ }
+ adc_tm->channels[i].tzd = tzd;
+ }
+
+ return 0;
+}
+
+static int adc_tm5_init(struct adc_tm5_chip *chip)
+{
+ u8 buf[4], channels_available;
+ int ret;
+ unsigned int i;
+
+ for (i = 0; i < chip->nchannels; i++) {
+ if (chip->channels[i].channel >= channels_available) {
+ dev_err(chip->dev, "Invalid channel %d\n", chip->channels[i].channel);
+ return -EINVAL;
+ }
+ }
+
+ ret = adc_tm5_read(chip, ADC_TM5_NUM_BTM,
+ &channels_available, sizeof(channels_available));
+ if (ret) {
+ dev_err(chip->dev, "read failed for BTM channels\n");
+ return ret;
+ }
+
+ buf[0] = chip->decimation;
+ buf[1] = chip->avg_samples | ADC_TM5_FAST_AVG_EN;
+ buf[2] = ADC_TM5_TIMER1;
+ buf[3] = FIELD_PREP(ADC_TM5_MEAS_INTERVAL_CTL2_MASK, ADC_TM5_TIMER2) |
+ FIELD_PREP(ADC_TM5_MEAS_INTERVAL_CTL3_MASK, ADC_TM5_TIMER3);
+
+ ret = adc_tm5_write(chip, ADC_TM5_ADC_DIG_PARAM, buf, sizeof(buf));
+ if (ret) {
+ dev_err(chip->dev, "block write failed: %d\n", ret);
+ return ret;
+ }
+
+ return ret;
+}
+
+static int adc_tm5_get_dt_channel_data(struct adc_tm5_chip *adc_tm,
+ struct adc_tm5_channel *channel,
+ struct device_node *node)
+{
+ const char *name = node->name;
+ u32 chan, value, varr[2];
+ int ret;
+ struct device *dev = adc_tm->dev;
+ struct of_phandle_args args;
+
+ ret = of_property_read_u32(node, "reg", &chan);
+ if (ret) {
+ dev_err(dev, "%s: invalid channel number %d\n", name, ret);
+ return ret;
+ }
+
+ if (chan >= ADC_TM5_NUM_CHANNELS) {
+ dev_err(dev, "%s: channel number too big: %d\n", name, chan);
+ return -EINVAL;
+ }
+
+ channel->channel = chan;
+
+ /*
+ * We are tied to PMIC's ADC controller, which always use single
+ * argument for channel number. So don't bother parsing
+ * #io-channel-cells, just enforce cell_count = 1.
+ */
+ ret = of_parse_phandle_with_fixed_args(node, "io-channels", 1, 0, &args);
+ if (ret < 0) {
+ dev_err(dev, "%s: error parsing ADC channel number %d: %d\n", name, chan, ret);
+ return ret;
+ }
+ of_node_put(args.np);
+
+ if (args.args_count != 1 || args.args[0] >= ADC5_MAX_CHANNEL) {
+ dev_err(dev, "%s: invalid ADC channel number %d\n", name, chan);
+ return ret;
+ }
+ channel->adc_channel = args.args[0];
+
+ channel->iio = devm_of_iio_channel_get_by_name(adc_tm->dev, node, NULL);
+ if (IS_ERR(channel->iio)) {
+ ret = PTR_ERR(channel->iio);
+ if (ret != -EPROBE_DEFER)
+ dev_err(dev, "%s: error getting channel: %d\n", name, ret);
+ return ret;
+ }
+
+ ret = of_property_read_u32_array(node, "qcom,pre-scaling", varr, 2);
+ if (!ret) {
+ ret = qcom_adc5_prescaling_from_dt(varr[0], varr[1]);
+ if (ret < 0) {
+ dev_err(dev, "%s: invalid pre-scaling <%d %d>\n",
+ name, varr[0], varr[1]);
+ return ret;
+ }
+ channel->prescale = ret;
+ } else {
+ /* 1:1 prescale is index 0 */
+ channel->prescale = 0;
+ }
+
+ ret = of_property_read_u32(node, "qcom,hw-settle-time-us", &value);
+ if (!ret) {
+ ret = qcom_adc5_hw_settle_time_from_dt(value, adc_tm->data->hw_settle);
+ if (ret < 0) {
+ dev_err(dev, "%s invalid hw-settle-time-us %d us\n",
+ name, value);
+ return ret;
+ }
+ channel->hw_settle_time = ret;
+ } else {
+ channel->hw_settle_time = VADC_DEF_HW_SETTLE_TIME;
+ }
+
+ if (of_property_read_bool(node, "qcom,ratiometric"))
+ channel->cal_method = ADC_TM5_RATIOMETRIC_CAL;
+ else
+ channel->cal_method = ADC_TM5_ABSOLUTE_CAL;
+
+ return 0;
+}
+
+static int adc_tm5_get_dt_data(struct adc_tm5_chip *adc_tm, struct device_node *node)
+{
+ struct adc_tm5_channel *channels;
+ struct device_node *child;
+ u32 value;
+ int ret;
+ struct device *dev = adc_tm->dev;
+
+ adc_tm->nchannels = of_get_available_child_count(node);
+ if (!adc_tm->nchannels)
+ return -EINVAL;
+
+ adc_tm->channels = devm_kcalloc(dev, adc_tm->nchannels,
+ sizeof(*adc_tm->channels), GFP_KERNEL);
+ if (!adc_tm->channels)
+ return -ENOMEM;
+
+ channels = adc_tm->channels;
+
+ adc_tm->data = of_device_get_match_data(dev);
+ if (!adc_tm->data)
+ adc_tm->data = &adc_tm5_data_pmic;
+
+ ret = of_property_read_u32(node, "qcom,decimation", &value);
+ if (!ret) {
+ ret = qcom_adc5_decimation_from_dt(value, adc_tm->data->decimation);
+ if (ret < 0) {
+ dev_err(dev, "invalid decimation %d\n", value);
+ return ret;
+ }
+ adc_tm->decimation = ret;
+ } else {
+ adc_tm->decimation = ADC5_DECIMATION_DEFAULT;
+ }
+
+ ret = of_property_read_u32(node, "qcom,avg-samples", &value);
+ if (!ret) {
+ ret = qcom_adc5_avg_samples_from_dt(value);
+ if (ret < 0) {
+ dev_err(dev, "invalid avg-samples %d\n", value);
+ return ret;
+ }
+ adc_tm->avg_samples = ret;
+ } else {
+ adc_tm->avg_samples = VADC_DEF_AVG_SAMPLES;
+ }
+
+ for_each_available_child_of_node(node, child) {
+ ret = adc_tm5_get_dt_channel_data(adc_tm, channels, child);
+ if (ret) {
+ of_node_put(child);
+ return ret;
+ }
+
+ channels++;
+ }
+
+ return 0;
+}
+
+static int adc_tm5_probe(struct platform_device *pdev)
+{
+ struct device_node *node = pdev->dev.of_node;
+ struct device *dev = &pdev->dev;
+ struct adc_tm5_chip *adc_tm;
+ struct regmap *regmap;
+ int ret, irq;
+ u32 reg;
+
+ regmap = dev_get_regmap(dev->parent, NULL);
+ if (!regmap)
+ return -ENODEV;
+
+ ret = of_property_read_u32(node, "reg", ®);
+ if (ret)
+ return ret;
+
+ adc_tm = devm_kzalloc(&pdev->dev, sizeof(*adc_tm), GFP_KERNEL);
+ if (!adc_tm)
+ return -ENOMEM;
+
+ adc_tm->regmap = regmap;
+ adc_tm->dev = dev;
+ adc_tm->base = reg;
+
+ irq = platform_get_irq(pdev, 0);
+ if (irq < 0) {
+ dev_err(dev, "get_irq failed: %d\n", irq);
+ return irq;
+ }
+
+ ret = adc_tm5_get_dt_data(adc_tm, node);
+ if (ret) {
+ dev_err(dev, "get dt data failed: %d\n", ret);
+ return ret;
+ }
+
+ ret = adc_tm5_init(adc_tm);
+ if (ret) {
+ dev_err(dev, "adc-tm init failed\n");
+ return ret;
+ }
+
+ ret = adc_tm5_register_tzd(adc_tm);
+ if (ret) {
+ dev_err(dev, "tzd register failed\n");
+ return ret;
+ }
+
+ return devm_request_threaded_irq(dev, irq, NULL, adc_tm5_isr,
+ IRQF_ONESHOT, "pm-adc-tm5", adc_tm);
+}
+
+static const struct of_device_id adc_tm5_match_table[] = {
+ {
+ .compatible = "qcom,spmi-adc-tm5",
+ .data = &adc_tm5_data_pmic,
+ },
+ { }
+};
+MODULE_DEVICE_TABLE(of, adc_tm5_match_table);
+
+static struct platform_driver adc_tm5_driver = {
+ .driver = {
+ .name = "qcom-spmi-adc-tm5",
+ .of_match_table = adc_tm5_match_table,
+ },
+ .probe = adc_tm5_probe,
+};
+module_platform_driver(adc_tm5_driver);
+
+MODULE_DESCRIPTION("SPMI PMIC Thermal Monitor ADC driver");
+MODULE_LICENSE("GPL v2");
projects / platform / kernel / linux-rpi.git / commitdiff