bool ssi_on_imx;
bool imx_ac97;
bool use_dma;
+ bool baudclk_locked;
+ bool irq_stats;
+ bool offline_config;
+ bool use_dual_fifo;
+ u8 i2s_mode;
+ spinlock_t baudclk_lock;
+ struct clk *baudclk;
struct clk *clk;
struct snd_dmaengine_dai_dma_data dma_params_tx;
struct snd_dmaengine_dai_dma_data dma_params_rx;
* because it is also running without an active substream. Normally SSI
* is only enabled when there is a substream.
*/
- if (ssi_private->imx_ac97) {
- /*
- * Setup the clock control register
- */
- write_ssi(CCSR_SSI_SxCCR_WL(17) | CCSR_SSI_SxCCR_DC(13),
- &ssi->stccr);
- write_ssi(CCSR_SSI_SxCCR_WL(17) | CCSR_SSI_SxCCR_DC(13),
- &ssi->srccr);
-
- /*
- * Enable AC97 mode and startup the SSI
- */
- write_ssi(CCSR_SSI_SACNT_AC97EN | CCSR_SSI_SACNT_FV,
- &ssi->sacnt);
- write_ssi(0xff, &ssi->saccdis);
- write_ssi(0x300, &ssi->saccen);
-
- /*
- * Enable SSI, Transmit and Receive
- */
- write_ssi_mask(&ssi->scr, 0, CCSR_SSI_SCR_SSIEN |
- CCSR_SSI_SCR_TE | CCSR_SSI_SCR_RE);
+ if (ssi_private->imx_ac97)
+ fsl_ssi_setup_ac97(ssi_private);
- write_ssi(CCSR_SSI_SOR_WAIT(3), &ssi->sor);
+ /*
+ * Set a default slot number so that there is no need for those common
+ * cases like I2S mode to call the extra set_tdm_slot() any more.
+ */
+ if (!ssi_private->imx_ac97) {
+ write_ssi_mask(&ssi->stccr, CCSR_SSI_SxCCR_DC_MASK,
+ CCSR_SSI_SxCCR_DC(2));
+ write_ssi_mask(&ssi->srccr, CCSR_SSI_SxCCR_DC_MASK,
+ CCSR_SSI_SxCCR_DC(2));
}
+ if (ssi_private->use_dual_fifo) {
+ write_ssi_mask(&ssi->srcr, 0, CCSR_SSI_SRCR_RFEN1);
+ write_ssi_mask(&ssi->stcr, 0, CCSR_SSI_STCR_TFEN1);
+ write_ssi_mask(&ssi->scr, 0, CCSR_SSI_SCR_TCH_EN);
+ }
+
return 0;
}
struct snd_soc_pcm_runtime *rtd = substream->private_data;
struct fsl_ssi_private *ssi_private =
snd_soc_dai_get_drvdata(rtd->cpu_dai);
- int synchronous = ssi_private->cpu_dai_drv.symmetric_rates;
+ unsigned long flags;
- /*
- * If this is the first stream opened, then request the IRQ
- * and initialize the SSI registers.
+ /* First, we only do fsl_ssi_setup() when SSI is going to be active.
+ * Second, fsl_ssi_setup was already called by ac97_init earlier if
+ * the driver is in ac97 mode.
*/
- if (!ssi_private->first_stream) {
- ssi_private->first_stream = substream;
-
- /*
- * fsl_ssi_setup was already called by ac97_init earlier if
- * the driver is in ac97 mode.
- */
- if (!ssi_private->imx_ac97)
- fsl_ssi_setup(ssi_private);
- } else {
- if (synchronous) {
- struct snd_pcm_runtime *first_runtime =
- ssi_private->first_stream->runtime;
- /*
- * This is the second stream open, and we're in
- * synchronous mode, so we need to impose sample
- * sample size constraints. This is because STCCR is
- * used for playback and capture in synchronous mode,
- * so there's no way to specify different word
- * lengths.
- *
- * Note that this can cause a race condition if the
- * second stream is opened before the first stream is
- * fully initialized. We provide some protection by
- * checking to make sure the first stream is
- * initialized, but it's not perfect. ALSA sometimes
- * re-initializes the driver with a different sample
- * rate or size. If the second stream is opened
- * before the first stream has received its final
- * parameters, then the second stream may be
- * constrained to the wrong sample rate or size.
- */
- if (first_runtime->sample_bits) {
- snd_pcm_hw_constraint_minmax(substream->runtime,
- SNDRV_PCM_HW_PARAM_SAMPLE_BITS,
- first_runtime->sample_bits,
- first_runtime->sample_bits);
- }
- }
-
- ssi_private->second_stream = substream;
+ if (!dai->active && !ssi_private->imx_ac97) {
+ fsl_ssi_setup(ssi_private);
+ spin_lock_irqsave(&ssi_private->baudclk_lock, flags);
+ ssi_private->baudclk_locked = false;
+ spin_unlock_irqrestore(&ssi_private->baudclk_lock, flags);
}
+ /* When using dual fifo mode, it is safer to ensure an even period
+ * size. If appearing to an odd number while DMA always starts its
+ * task from fifo0, fifo1 would be neglected at the end of each
+ * period. But SSI would still access fifo1 with an invalid data.
+ */
+ if (ssi_private->use_dual_fifo)
+ snd_pcm_hw_constraint_step(substream->runtime, 0,
+ SNDRV_PCM_HW_PARAM_PERIOD_SIZE, 2);
+
return 0;
}
/* Older 8610 DTs didn't have the fifo-depth property */
ssi_private->fifo_depth = 8;
- if (of_device_is_compatible(pdev->dev.of_node, "fsl,imx21-ssi")) {
+ ssi_private->baudclk_locked = false;
+ spin_lock_init(&ssi_private->baudclk_lock);
+
+ /*
+ * imx51 and later SoCs have a slightly different IP that allows the
+ * SSI configuration while the SSI unit is running.
+ *
+ * More important, it is necessary on those SoCs to configure the
+ * sperate TX/RX DMA bits just before starting the stream
+ * (fsl_ssi_trigger). The SDMA unit has to be configured before fsl_ssi
+ * sends any DMA requests to the SDMA unit, otherwise it is not defined
+ * how the SDMA unit handles the DMA request.
+ *
+ * SDMA units are present on devices starting at imx35 but the imx35
+ * reference manual states that the DMA bits should not be changed
+ * while the SSI unit is running (SSIEN). So we support the necessary
+ * online configuration of fsl-ssi starting at imx51.
+ */
+ switch (hw_type) {
+ case FSL_SSI_MCP8610:
+ case FSL_SSI_MX21:
+ case FSL_SSI_MX35:
+ ssi_private->offline_config = true;
+ break;
+ case FSL_SSI_MX51:
+ ssi_private->offline_config = false;
+ break;
+ }
+
+ if (hw_type == FSL_SSI_MX21 || hw_type == FSL_SSI_MX51 ||
+ hw_type == FSL_SSI_MX35) {
- u32 dma_events[2];
+ u32 dma_events[2], dmas[4];
ssi_private->ssi_on_imx = true;
ssi_private->clk = devm_clk_get(&pdev->dev, NULL);
goto error_clk;
}
}
-
- shared = of_device_is_compatible(of_get_parent(np),
- "fsl,spba-bus");
-
- imx_pcm_dma_params_init_data(&ssi_private->filter_data_tx,
- dma_events[0], shared ? IMX_DMATYPE_SSI_SP : IMX_DMATYPE_SSI);
- imx_pcm_dma_params_init_data(&ssi_private->filter_data_rx,
- dma_events[1], shared ? IMX_DMATYPE_SSI_SP : IMX_DMATYPE_SSI);
++ /* Should this be merge with the above? */
+ if (!of_property_read_u32_array(pdev->dev.of_node, "dmas", dmas, 4)
+ && dmas[2] == IMX_DMATYPE_SSI_DUAL) {
+ ssi_private->use_dual_fifo = true;
+ /* When using dual fifo mode, we need to keep watermark
+ * as even numbers due to dma script limitation.
+ */
+ ssi_private->dma_params_tx.maxburst &= ~0x1;
+ ssi_private->dma_params_rx.maxburst &= ~0x1;
+ }
- } else if (ssi_private->use_dma) {
+
+ shared = of_device_is_compatible(of_get_parent(np),
+ "fsl,spba-bus");
+
+ imx_pcm_dma_params_init_data(&ssi_private->filter_data_tx,
+ dma_events[0], shared ? IMX_DMATYPE_SSI_SP : IMX_DMATYPE_SSI);
+ imx_pcm_dma_params_init_data(&ssi_private->filter_data_rx,
+ dma_events[1], shared ? IMX_DMATYPE_SSI_SP : IMX_DMATYPE_SSI);
+ }
+
+ /*
+ * Enable interrupts only for MCP8610 and MX51. The other MXs have
+ * different writeable interrupt status registers.
+ */
+ if (ssi_private->use_dma) {
/* The 'name' should not have any slashes in it. */
ret = devm_request_irq(&pdev->dev, ssi_private->irq,
fsl_ssi_isr, 0, ssi_private->name,
projects / platform / kernel / linux-exynos.git / commitdiff