arm: dts: k3-am68-sk: Add r5 specific dt support

Add initial support for AM68 SK device tree that runs on R5.

Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>

diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index d397076..3ecd6a8 100644 (file)
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -1255,6 +1255,7 @@ dtb-$(CONFIG_SOC_K3_J721E) += k3-j721e-common-proc-board.dtb \
                              k3-j721e-sk.dtb \
                              k3-j721e-r5-sk.dtb
 dtb-$(CONFIG_SOC_K3_J721S2) += k3-am68-sk-base-board.dtb\
+                              k3-am68-sk-r5-base-board.dtb\
                               k3-j721s2-common-proc-board.dtb\
                               k3-j721s2-r5-common-proc-board.dtb
 dtb-$(CONFIG_SOC_K3_AM642) += k3-am642-evm.dtb \

diff --git a/arch/arm/dts/k3-am68-sk-r5-base-board.dts b/arch/arm/dts/k3-am68-sk-r5-base-board.dts
new file mode 100644 (file)
index 0000000..46ee6c4
--- /dev/null
+++ b/arch/arm/dts/k3-am68-sk-r5-base-board.dts
@@ -0,0 +1,194 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2022 Texas Instruments Incorporated - https://www.ti.com/
+ */
+
+/dts-v1/;
+
+#include "k3-am68-sk-som.dtsi"
+#include "k3-j721s2-ddr-evm-lp4-4266.dtsi"
+#include "k3-j721s2-ddr.dtsi"
+
+/ {
+       chosen {
+               firmware-loader = &fs_loader0;
+               stdout-path = &main_uart8;
+               tick-timer = &timer1;
+       };
+
+       aliases {
+               remoteproc0 = &sysctrler;
+               remoteproc1 = &a72_0;
+       };
+
+       fs_loader0: fs_loader@0 {
+               compatible = "u-boot,fs-loader";
+               u-boot,dm-pre-reloc;
+       };
+
+       a72_0: a72@0 {
+               compatible = "ti,am654-rproc";
+               reg = <0x0 0x00a90000 0x0 0x10>;
+               power-domains = <&k3_pds 61 TI_SCI_PD_EXCLUSIVE>,
+                               <&k3_pds 202 TI_SCI_PD_EXCLUSIVE>;
+               resets = <&k3_reset 202 0>;
+               clocks = <&k3_clks 61 1>;
+               assigned-clocks = <&k3_clks 61 1>, <&k3_clks 202 0>;
+               assigned-clock-parents = <&k3_clks 61 2>;
+               assigned-clock-rates = <200000000>, <2000000000>;
+               ti,sci = <&sms>;
+               ti,sci-proc-id = <32>;
+               ti,sci-host-id = <10>;
+               u-boot,dm-spl;
+       };
+
+       clk_200mhz: dummy_clock_200mhz {
+               compatible = "fixed-clock";
+               #clock-cells = <0>;
+               clock-frequency = <200000000>;
+               u-boot,dm-spl;
+       };
+
+       clk_19_2mhz: dummy_clock_19_2mhz {
+               compatible = "fixed-clock";
+               #clock-cells = <0>;
+               clock-frequency = <19200000>;
+               u-boot,dm-spl;
+       };
+};
+
+&cbass_mcu_wakeup {
+       sa3_secproxy: secproxy@44880000 {
+               u-boot,dm-spl;
+               compatible = "ti,am654-secure-proxy";
+               reg = <0x0 0x44880000 0x0 0x20000>,
+                     <0x0 0x44860000 0x0 0x20000>,
+                     <0x0 0x43600000 0x0 0x10000>;
+               reg-names = "rt", "scfg", "target_data";
+               #mbox-cells = <1>;
+       };
+
+       mcu_secproxy: secproxy@2a380000 {
+               compatible = "ti,am654-secure-proxy";
+               reg = <0x0 0x2a380000 0x0 0x80000>,
+                     <0x0 0x2a400000 0x0 0x80000>,
+                     <0x0 0x2a480000 0x0 0x80000>;
+               reg-names = "rt", "scfg", "target_data";
+               #mbox-cells = <1>;
+               u-boot,dm-spl;
+       };
+
+       sysctrler: sysctrler {
+               compatible = "ti,am654-system-controller";
+               mboxes= <&mcu_secproxy 4>, <&mcu_secproxy 5>, <&sa3_secproxy 5>;
+               mbox-names = "tx", "rx", "boot_notify";
+               u-boot,dm-spl;
+       };
+
+       dm_tifs: dm-tifs {
+               compatible = "ti,j721e-dm-sci";
+               ti,host-id = <3>;
+               ti,secure-host;
+               mbox-names = "rx", "tx";
+               mboxes= <&mcu_secproxy 21>,
+                       <&mcu_secproxy 23>;
+               u-boot,dm-spl;
+       };
+};
+
+&main_pmx0 {
+       main_uart8_pins_default: main-uart8-pins-default {
+               pinctrl-single,pins = <
+                       J721S2_IOPAD(0x0d0, PIN_INPUT, 11) /* (AF26) SPI0_CS1.UART8_RXD */
+                       J721S2_IOPAD(0x0d4, PIN_OUTPUT, 11) /* (AH27) SPI0_CLK.UART8_TXD */
+               >;
+       };
+
+       main_mmc1_pins_default: main-mmc1-pins-default {
+               pinctrl-single,pins = <
+                       J721S2_IOPAD(0x104, PIN_INPUT, 0) /* (P23) MMC1_CLK */
+                       J721S2_IOPAD(0x108, PIN_INPUT, 0) /* (N24) MMC1_CMD */
+                       J721S2_IOPAD(0x100, PIN_INPUT, 0) /* (###) MMC1_CLKLB */
+                       J721S2_IOPAD(0x0fc, PIN_INPUT, 0) /* (M23) MMC1_DAT0 */
+                       J721S2_IOPAD(0x0f8, PIN_INPUT, 0) /* (P24) MMC1_DAT1 */
+                       J721S2_IOPAD(0x0f4, PIN_INPUT, 0) /* (R24) MMC1_DAT2 */
+                       J721S2_IOPAD(0x0f0, PIN_INPUT, 0) /* (R22) MMC1_DAT3 */
+                       J721S2_IOPAD(0x0e8, PIN_INPUT, 8) /* (AE25) TIMER_IO0.MMC1_SDCD */
+               >;
+       };
+
+       main_usbss0_pins_default: main-usbss0-pins-default {
+               pinctrl-single,pins = <
+                       J721S2_IOPAD(0x0ec, PIN_OUTPUT, 6) /* (AG25) TIMER_IO1.USB0_DRVVBUS */
+               >;
+       };
+};
+
+&wkup_pmx0 {
+       mcu_uart0_pins_default: mcu-uart0-pins-default {
+               u-boot,dm-spl;
+               pinctrl-single,pins = <
+                       J721S2_WKUP_IOPAD(0x0f4, PIN_INPUT, 0) /*(C24) WKUP_GPIO0_13.MCU_UART0_RXD*/
+                       J721S2_WKUP_IOPAD(0x0f0, PIN_OUTPUT, 0) /*(C25) WKUP_GPIO0_12.MCU_UART0_TXD*/
+               >;
+       };
+
+       wkup_uart0_pins_default: wkup-uart0-pins-default {
+               u-boot,dm-spl;
+               pinctrl-single,pins = <
+                       J721S2_WKUP_IOPAD(0x0d8, PIN_INPUT, 0) /*(E25) WKUP_GPIO0_6.WKUP_UART0_CTSn*/
+                       J721S2_WKUP_IOPAD(0x0dc, PIN_OUTPUT, 0) /*(F28) WKUP_GPIO0_7.WKUP_UART0_RTSn*/
+                       J721S2_WKUP_IOPAD(0x0b0, PIN_INPUT, 0) /* (D28) WKUP_UART0_RXD */
+                       J721S2_WKUP_IOPAD(0x0b4, PIN_OUTPUT, 0) /* (D27) WKUP_UART0_TXD */
+               >;
+       };
+
+};
+
+&sms {
+       mboxes= <&mcu_secproxy 8>, <&mcu_secproxy 6>, <&mcu_secproxy 5>;
+       mbox-names = "tx", "rx", "notify";
+       ti,host-id = <4>;
+       ti,secure-host;
+       u-boot,dm-spl;
+};
+
+&wkup_uart0 {
+       pinctrl-names = "default";
+       pinctrl-0 = <&wkup_uart0_pins_default>;
+};
+
+&mcu_uart0 {
+       pinctrl-names = "default";
+       pinctrl-0 = <&mcu_uart0_pins_default>;
+};
+
+&main_uart8 {
+       pinctrl-names = "default";
+       pinctrl-0 = <&main_uart8_pins_default>;
+};
+
+&main_sdhci0 {
+       status = "disabled";
+};
+
+&main_sdhci1 {
+       /delete-property/ power-domains;
+       /delete-property/ assigned-clocks;
+       /delete-property/ assigned-clock-parents;
+       pinctrl-0 = <&main_mmc1_pins_default>;
+       pinctrl-names = "default";
+       clock-names = "clk_xin";
+       clocks = <&clk_200mhz>;
+       ti,driver-strength-ohm = <50>;
+};
+
+&mcu_ringacc {
+       ti,sci = <&dm_tifs>;
+};
+
+&mcu_udmap {
+       ti,sci = <&dm_tifs>;
+};
+
+#include "k3-am68-sk-base-board-u-boot.dtsi"