#ifdef CONFIG_SYS_FSL_ERRATUM_NMG_LBC103
puts("Work-around for Erratum NMG_LBC103 enabled\n");
#endif
+#ifdef CONFIG_SYS_FSL_ERRATUM_NMG_ETSEC129
+ if ((SVR_MAJ(svr) == 1) || IS_SVR_REV(svr, 2, 0))
+ puts("Work-around for Erratum NMG ETSEC129 enabled\n");
+#endif
return 0;
}
volatile ccsr_l2cache_t *l2cache = (void *)CONFIG_SYS_MPC85xx_L2_ADDR;
volatile uint cache_ctl;
uint svr, ver;
- uint l2srbar;
u32 l2siz_field;
svr = get_svr();
if (l2cache->l2ctl & MPC85xx_L2CTL_L2E) {
puts("already enabled");
- l2srbar = l2cache->l2srbar0;
#if defined(CONFIG_SYS_INIT_L2_ADDR) && defined(CONFIG_SYS_FLASH_BASE)
+ u32 l2srbar = l2cache->l2srbar0;
if (l2cache->l2ctl & MPC85xx_L2CTL_L2SRAM_ENTIRE
&& l2srbar >= CONFIG_SYS_FLASH_BASE) {
l2srbar = CONFIG_SYS_INIT_L2_ADDR;
#endif
#if defined(CONFIG_SYS_FSL_ERRATUM_IFC_A003399) && !defined(CONFIG_SYS_RAMBOOT)
ccsr_l2cache_t *l2cache = (void *)CONFIG_SYS_MPC85xx_L2_ADDR;
- u32 *l2srbar, *dst, *src;
+ u32 *dst, *src;
void (*setup_ifc_sram)(void);
#endif
dst = (u32 *) SRAM_BASE_ADDR;
src = (u32 *) setup_ifc;
for (i = 0; i < 1024; i++)
- *l2srbar++ = *src++;
+ *dst++ = *src++;
setup_ifc_sram();
int cfg;
serdes_corenet_t *srds_regs;
int lane, bank, idx;
- enum srds_prtcl lane_prtcl;
int have_bank[SRDS_MAX_BANK] = {};
#ifdef CONFIG_SYS_P4080_ERRATUM_SERDES8
u32 serdes8_devdisr = 0;
#ifdef CONFIG_SYS_P4080_ERRATUM_SERDES_A001
int need_serdes_a001; /* TRUE == need work-around for SERDES A001 */
#endif
+#ifdef CONFIG_SYS_P4080_ERRATUM_SERDES8
char buffer[HWCONFIG_BUFFER_SIZE];
char *buf = NULL;
*/
if (getenv_f("hwconfig", buffer, sizeof(buffer)) > 0)
buf = buffer;
+#endif
/* Is serdes enabled at all? */
if (!(in_be32(&gur->rcwsr[5]) & FSL_CORENET_RCWSR5_SRDS_EN))
}
}
+#if defined(CONFIG_SYS_P4080_ERRATUM_SERDES8) || defined (CONFIG_SYS_P4080_ERRATUM_SERDES9)
for (lane = 0; lane < SRDS_MAX_LANES; lane++) {
+ enum srds_prtcl lane_prtcl;
+
idx = serdes_get_lane_idx(lane);
lane_prtcl = serdes_get_prtcl(cfg, lane);
#endif
}
+#endif
#ifdef DEBUG
puts("\n");
#endif /* CONFIG_MPC8569 */
/*
+ * Search for the TLB that covers the code we're executing, and shrink it
+ * so that it covers only this 4K page. That will ensure that any other
+ * TLB we create won't interfere with it. We assume that the TLB exists,
+ * which is why we don't check the Valid bit of MAS1.
+ *
+ * This is necessary, for example, when booting from the on-chip ROM,
+ * which (oddly) creates a single 4GB TLB that covers CCSR and DDR.
+ * If we don't shrink this TLB now, then we'll accidentally delete it
+ * in "purge_old_ccsr_tlb" below.
+ */
+ bl nexti /* Find our address */
+nexti: mflr r1 /* R1 = our PC */
+ li r2, 0
+ mtspr MAS6, r2 /* Assume the current PID and AS are 0 */
+ isync
+ msync
+ tlbsx 0, r1 /* This must succeed */
+
+ /* Set the size of the TLB to 4KB */
+ mfspr r3, MAS1
+ li r2, 0xF00
+ andc r3, r3, r2 /* Clear the TSIZE bits */
+ ori r3, r3, MAS1_TSIZE(BOOKE_PAGESZ_4K)@l
+ mtspr MAS1, r3
+
+ /*
+ * Set the base address of the TLB to our PC. We assume that
+ * virtual == physical. We also assume that MAS2_EPN == MAS3_RPN.
+ */
+ lis r3, MAS2_EPN@h
+ ori r3, r3, MAS2_EPN@l /* R3 = MAS2_EPN */
+
+ and r1, r1, r3 /* Our PC, rounded down to the nearest page */
+
+ mfspr r2, MAS2
+ andc r2, r2, r3
+ or r2, r2, r1
+ mtspr MAS2, r2 /* Set the EPN to our PC base address */
+
+ mfspr r2, MAS3
+ andc r2, r2, r3
+ or r2, r2, r1
+ mtspr MAS3, r2 /* Set the RPN to our PC base address */
+
+ isync
+ msync
+ tlbwe
+
+/*
* Relocate CCSR, if necessary. We relocate CCSR if (obviously) the default
* location is not where we want it. This typically happens on a 36-bit
* system, where we want to move CCSR to near the top of 36-bit address space.
li r1, 0
mtspr MAS6, r1 /* Search the current address space and PID */
+ isync
+ msync
tlbsx 0, r8
mfspr r1, MAS1
andis. r2, r1, MAS1_VALID@h /* Check for the Valid bit */
rlwinm r1, r1, 0, 1, 31 /* Clear Valid bit */
mtspr MAS1, r1
+ isync
+ msync
tlbwe
1:
tlbwe
/*
- * Create a TLB for the old location of CCSR. Register R9 is reserved
+ * Create a TLB for the current location of CCSR. Register R9 is reserved
* for the virtual address of this TLB (CONFIG_SYS_CCSRBAR + 0x1000).
*/
create_ccsr_old_tlb:
msync
tlbwe
+ /*
+ * We have a TLB for what we think is the current (old) CCSR. Let's
+ * verify that, otherwise we won't be able to move it.
+ * CONFIG_SYS_CCSRBAR_DEFAULT is always a 32-bit number, so we only
+ * need to compare the lower 32 bits of CCSRBAR on CoreNet systems.
+ */
+verify_old_ccsr:
+ lis r0, CONFIG_SYS_CCSRBAR_DEFAULT@h
+ ori r0, r0, CONFIG_SYS_CCSRBAR_DEFAULT@l
+#ifdef CONFIG_FSL_CORENET
+ lwz r1, 4(r9) /* CCSRBARL */
+#else
+ lwz r1, 0(r9) /* CCSRBAR, shifted right by 12 */
+ slwi r1, r1, 12
+#endif
+
+ cmpl 0, r0, r1
+
+ /*
+ * If the value we read from CCSRBARL is not what we expect, then
+ * enter an infinite loop. This will at least allow a debugger to
+ * halt execution and examine TLBs, etc. There's no point in going
+ * on.
+ */
+infinite_debug_loop:
+ bne infinite_debug_loop
+
#ifdef CONFIG_FSL_CORENET
#define CCSR_LAWBARH0 (CONFIG_SYS_CCSRBAR + 0x1000)
*/
read_old_ccsrbar:
lwz r0, 0(r9) /* CCSRBARH */
- lwz r0, 4(r9) /* CCSRBARH */
+ lwz r0, 4(r9) /* CCSRBARL */
isync
/*
void disable_tlb(u8 esel)
{
- u32 _mas0, _mas1, _mas2, _mas3, _mas7;
+ u32 _mas0, _mas1, _mas2, _mas3;
free_tlb_cam(esel);
_mas1 = 0;
_mas2 = 0;
_mas3 = 0;
- _mas7 = 0;
mtspr(MAS0, _mas0);
mtspr(MAS1, _mas1);
mtspr(MAS2, _mas2);
mtspr(MAS3, _mas3);
#ifdef CONFIG_ENABLE_36BIT_PHYS
- mtspr(MAS7, _mas7);
+ mtspr(MAS7, 0);
#endif
asm volatile("isync;msync;tlbwe;isync");
unsigned int tlb_size;
unsigned int wimge = 0;
unsigned int ram_tlb_address = (unsigned int)CONFIG_SYS_DDR_SDRAM_BASE;
- unsigned int max_cam = (mfspr(SPRN_TLB1CFG) >> 16) & 0xf;
+ unsigned int max_cam;
u64 size, memsize = (u64)memsize_in_meg << 20;
#ifdef CONFIG_SYS_PPC_DDR_WIMGE
wimge = CONFIG_SYS_PPC_DDR_WIMGE;
#endif
size = min(memsize, CONFIG_MAX_MEM_MAPPED);
-
- /* Convert (4^max) kB to (2^max) bytes */
- max_cam = max_cam * 2 + 10;
+ if ((mfspr(SPRN_MMUCFG) & MMUCFG_MAVN) == MMUCFG_MAVN_V1) {
+ /* Convert (4^max) kB to (2^max) bytes */
+ max_cam = ((mfspr(SPRN_TLB1CFG) >> 16) & 0xf) * 2 + 10;
+ } else {
+ /* Convert (2^max) kB to (2^max) bytes */
+ max_cam = __ilog2(mfspr(SPRN_TLB1PS)) + 10;
+ }
for (i = 0; size && i < 8; i++) {
int ram_tlb_index = find_free_tlbcam();
rcw_en = 1;
ap_en = popts->ap_en;
} else {
- rcw_en = 0;
ap_en = 0;
}
| ((obc_cfg & 0x1) << 6)
| ((ap_en & 0x1) << 5)
| ((d_init & 0x1) << 4)
-#ifdef CONFIG_FSL_DDR3
| ((rcw_en & 0x1) << 2)
-#endif
| ((md_en & 0x1) << 0)
);
debug("FSLDDR: ddr_sdram_cfg_2 = 0x%08x\n", ddr->ddr_sdram_cfg_2);
#ifdef CONFIG_FSL_DDR3
if (unq_mrs_en) { /* unique mode registers are supported */
- for (i = 1; i < 4; i++) {
+ for (i = 1; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) {
if (popts->rtt_override)
rtt_wr = popts->rtt_wr_override_value;
else
debug("FSLDDR: ddr_sdram_mode = 0x%08x\n", ddr->ddr_sdram_mode);
if (unq_mrs_en) { /* unique mode registers are supported */
- for (i = 1; i < 4; i++) {
+ for (i = 1; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) {
if (popts->rtt_override)
rtt = popts->rtt_override_value;
else
unsigned int i;
char buffer[HWCONFIG_BUFFER_SIZE];
char *buf = NULL;
+#if defined(CONFIG_FSL_DDR3) || defined(CONFIG_FSL_DDR2)
const struct dynamic_odt *pdodt = odt_unknown;
+#endif
ulong ddr_freq;
/*
if (getenv_f("hwconfig", buffer, sizeof(buffer)) > 0)
buf = buffer;
+#if defined(CONFIG_FSL_DDR3) || defined(CONFIG_FSL_DDR2)
/* Chip select options. */
if (CONFIG_DIMM_SLOTS_PER_CTLR == 1) {
switch (pdimm[0].n_ranks) {
break;
}
}
+#endif
/* Pick chip-select local options. */
for (i = 0; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) {
#endif /* defined(CONFIG_MPC85xx) || defined(CONFIG_MPC86xx) */
#ifdef CONFIG_HAS_FSL_DR_USB
-static void fdt_fixup_usb_mode_phy_type(void *blob, const char *mode,
- const char *phy_type)
+static int fdt_fixup_usb_mode_phy_type(void *blob, const char *mode,
+ const char *phy_type, int start_offset)
{
const char *compat = "fsl-usb2-dr";
const char *prop_mode = "dr_mode";
const char *prop_type = "phy_type";
- static int start_offset = -1;
int node_offset;
int err;
if (node_offset < 0) {
printf("WARNING: could not find compatible node %s: %s.\n",
compat, fdt_strerror(node_offset));
- return;
+ return -1;
}
if (mode) {
prop_type, compat, fdt_strerror(err));
}
- start_offset = node_offset;
+ return node_offset;
}
void fdt_fixup_dr_usb(void *blob, bd_t *bd)
{
const char *modes[] = { "host", "peripheral", "otg" };
- const char *phys[] = { "ulpi", "umti" };
+ const char *phys[] = { "ulpi", "utmi" };
const char *mode = NULL;
const char *phy_type = NULL;
char usb1_defined = 0;
+ int usb_mode_off = -1;
+ int usb_phy_off = -1;
char str[5];
int i, j;
}
}
if (mode_idx >= 0)
- fdt_fixup_usb_mode_phy_type(blob,
- modes[mode_idx], NULL);
+ usb_mode_off = fdt_fixup_usb_mode_phy_type(blob,
+ modes[mode_idx], NULL, usb_mode_off);
if (phy_idx >= 0)
- fdt_fixup_usb_mode_phy_type(blob,
- NULL, phys[phy_idx]);
+ usb_phy_off = fdt_fixup_usb_mode_phy_type(blob,
+ NULL, phys[phy_idx], usb_phy_off);
if (!strcmp(str, "usb1"))
usb1_defined = 1;
if (mode_idx < 0 && phy_idx < 0)
}
}
if (!usb1_defined) {
+ int usb_off = -1;
mode = getenv("usb_dr_mode");
phy_type = getenv("usb_phy_type");
if (!mode && !phy_type)
return;
- fdt_fixup_usb_mode_phy_type(blob, mode, phy_type);
+ fdt_fixup_usb_mode_phy_type(blob, mode, phy_type, usb_off);
}
}
#endif /* CONFIG_HAS_FSL_DR_USB */
void upmconfig(uint upm, uint *table, uint size)
{
fsl_lbc_t *lbc = LBC_BASE_ADDR;
- int i, mdr, mad, old_mad = 0;
+ int i, mad, old_mad = 0;
u32 mask = (~MxMR_OP_MSK & ~MxMR_MAD_MSK);
u32 msel = BR_UPMx_TO_MSEL(upm);
u32 *mxmr = &lbc->mamr + upm;
for (i = 0; i < size; i++) {
out_be32(mxmr, (in_be32(mxmr) & mask) | MxMR_OP_WARR | i);
out_be32(&lbc->mdr, table[i]);
- mdr = in_be32(&lbc->mdr);
+ (void)in_be32(&lbc->mdr);
*dummy = 0;
do {
mad = in_be32(mxmr) & MxMR_MAD_MSK;
#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000
#define CONFIG_SYS_FSL_ERRATUM_NMG_DDR120
#define CONFIG_SYS_FSL_ERRATUM_NMG_LBC103
+#define CONFIG_SYS_FSL_ERRATUM_NMG_ETSEC129
#elif defined(CONFIG_MPC8555)
#define CONFIG_MAX_CPUS 1
*/
#define MAS0_TLBSEL_MSK 0x30000000
-#define MAS0_TLBSEL(x) ((x << 28) & MAS0_TLBSEL_MSK)
+#define MAS0_TLBSEL(x) (((x) << 28) & MAS0_TLBSEL_MSK)
#define MAS0_ESEL_MSK 0x0FFF0000
-#define MAS0_ESEL(x) ((x << 16) & MAS0_ESEL_MSK)
+#define MAS0_ESEL(x) (((x) << 16) & MAS0_ESEL_MSK)
#define MAS0_NV(x) ((x) & 0x00000FFF)
#define MAS1_VALID 0x80000000
#define MAS1_IPROT 0x40000000
-#define MAS1_TID(x) ((x << 16) & 0x3FFF0000)
+#define MAS1_TID(x) (((x) << 16) & 0x3FFF0000)
#define MAS1_TS 0x00001000
-#define MAS1_TSIZE(x) ((x << 8) & 0x00000F00)
-#define TSIZE_TO_BYTES(x) ((phys_addr_t)(1UL << ((tsize * 2) + 10)))
+#define MAS1_TSIZE(x) (((x) << 8) & 0x00000F00)
+#define TSIZE_TO_BYTES(x) (1ULL << (((x) * 2) + 10))
#define MAS2_EPN 0xFFFFF000
#define MAS2_X0 0x00000040
#define SPRN_TLB0CFG 0x2B0 /* TLB 0 Config Register */
#define SPRN_TLB1CFG 0x2B1 /* TLB 1 Config Register */
+#define SPRN_TLB0PS 0x158 /* TLB 0 Page Size Register */
+#define SPRN_TLB1PS 0x159 /* TLB 1 Page Size Register */
#define SPRN_MMUCSR0 0x3f4 /* MMU control and status register 0 */
+#define SPRN_MMUCFG 0x3F7 /* MMU Configuration Register */
+#define MMUCFG_MAVN 0x00000003 /* MMU Architecture Version Number */
+#define MMUCFG_MAVN_V1 0x00000000 /* v1.0 */
+#define MMUCFG_MAVN_V2 0x00000001 /* v2.0 */
#define SPRN_MAS0 0x270 /* MMU Assist Register 0 */
#define SPRN_MAS1 0x271 /* MMU Assist Register 1 */
#define SPRN_MAS2 0x272 /* MMU Assist Register 2 */
#if defined(CONFIG_OF_BOARD_SETUP)
static void cds_pci_fixup(void *blob)
{
- int node, tmp[2];
+ int node;
const char *path;
int len, slot, i;
u32 *map = NULL;
node = fdt_path_offset(blob, "/aliases");
- tmp[0] = 0;
if (node >= 0) {
path = fdt_getprop(blob, node, "pci0", NULL);
if (path) {
#include "pixis.h"
#endif
+/* define for SYS CLK or CLK1Frequency */
+#define TTL 1
+#define CLK2 0
+#define CRYSTAL 0
+#define MAX_VDW (511 + 8)
+#define MAX_RDW (127 + 2)
+#define MIN_VDW (4 + 8)
+#define MIN_RDW (1 + 2)
+#define NUM_OD_SETTING 8
+/*
+ * These defines cover the industrial temperature range part,
+ * for commercial, change below to 400000 and 55000, respectively
+ */
+#define MAX_VCO 360000
+#define MIN_VCO 60000
+
/* decode S[0-2] to Output Divider (OD) */
static u8 ics307_s_to_od[] = {
10, 2, 8, 4, 5, 7, 3, 6
};
/*
+ * Find one solution to generate required frequency for SYSCLK
+ * out_freq: KHz, required frequency to the SYSCLK
+ * the result will be retuned with component RDW, VDW, OD, TTL,
+ * CLK2 and crystal
+ */
+unsigned long ics307_sysclk_calculator(unsigned long out_freq)
+{
+ const unsigned long input_freq = CONFIG_ICS307_REFCLK_HZ;
+ unsigned long vdw, rdw, odp, s_vdw = 0, s_rdw = 0, s_odp = 0, od;
+ unsigned long tmp_out, diff, result = 0;
+ int found = 0;
+
+ for (odp = 0; odp < NUM_OD_SETTING; odp++) {
+ od = ics307_s_to_od[odp];
+ if (od * out_freq < MIN_VCO || od * out_freq > MAX_VCO)
+ continue;
+ for (rdw = MIN_RDW; rdw <= MAX_RDW; rdw++) {
+ /* Calculate the VDW */
+ vdw = out_freq * 1000 * od * rdw / (input_freq * 2);
+ if (vdw > MAX_VDW)
+ vdw = MAX_VDW;
+ if (vdw < MIN_VDW)
+ continue;
+ /* Calculate the temp out frequency */
+ tmp_out = input_freq * 2 * vdw / (rdw * od * 1000);
+ diff = MAX(out_freq, tmp_out) - MIN(out_freq, tmp_out);
+ /*
+ * calculate the percent, the precision is 1/1000
+ * If greater than 1/1000, continue
+ * otherwise, we think the solution is we required
+ */
+ if (diff * 1000 / out_freq > 1)
+ continue;
+ else {
+ s_vdw = vdw;
+ s_rdw = rdw;
+ s_odp = odp;
+ found = 1;
+ break;
+ }
+ }
+ }
+
+ if (found)
+ result = (s_rdw - 2) | (s_vdw - 8) << 7 | s_odp << 16 |
+ CLK2 << 19 | TTL << 21 | CRYSTAL << 22;
+
+ debug("ICS307-02: RDW: %ld, VDW: %ld, OD: %d\n", s_rdw - 2, s_vdw - 8,
+ ics307_s_to_od[s_odp]);
+ return result;
+}
+
+/*
* Calculate frequency being generated by ICS307-02 clock chip based upon
* the control bytes being programmed into it.
*/
/*
- * Copyright 2010 Freescale Semiconductor, Inc.
+ * Copyright 2010-2011 Freescale Semiconductor, Inc.
*
* See file CREDITS for list of people who contributed to this
* project.
#define __ICS_CLK_H_ 1
#ifndef __ASSEMBLY__
+
extern unsigned long get_board_sys_clk(void);
extern unsigned long get_board_ddr_clk(void);
+extern unsigned long ics307_sysclk_calculator(unsigned long out_freq);
#endif
#endif /* __ICS_CLK_H_ */
}
#endif
+void pixis_sysclk_set(unsigned long sysclk)
+{
+ unsigned long freq_word;
+ u8 sclk0, sclk1, sclk2;
+
+ freq_word = ics307_sysclk_calculator(sysclk);
+ sclk2 = freq_word & 0xff;
+ sclk1 = (freq_word >> 8) & 0xff;
+ sclk0 = (freq_word >> 16) & 0xff;
+
+ /* set SYSCLK enable bit */
+ PIXIS_WRITE(vcfgen0, 0x01);
+
+ /* SYSCLK to required frequency */
+ PIXIS_WRITE(sclk[0], sclk0);
+ PIXIS_WRITE(sclk[1], sclk1);
+ PIXIS_WRITE(sclk[2], sclk2);
+}
+
int pixis_reset_cmd(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
{
unsigned int i;
+ unsigned long sysclk;
char *p_altbank = NULL;
#ifdef DEBUG
char *p_dump = NULL;
continue;
}
#endif
+ if (strcmp(argv[i], "sysclk") == 0) {
+ sysclk = simple_strtoul(argv[i + 1], NULL, 0);
+ i += 1;
+ pixis_sysclk_set(sysclk);
+ continue;
+ }
unknown_param = argv[i];
}
#ifdef DEBUG
"pixis_reset dump - display the PIXIS registers\n"
#endif
+ "pixis_reset sysclk <SYSCLK_freq> - reset with SYSCLK frequency(KHz)\n"
);
{
int i, j;
int mulconst;
- int intarr_len, no_dec = 0;
+ int no_dec = 0;
unsigned long intval = 0, decval = 0;
char intarr[3], decarr[3];
i++;
}
- /* Assign length of integer part to intarr_len. */
- intarr_len = i;
intarr[i] = '\0';
if (no_dec) {
int board_eth_init(bd_t *bis)
{
#ifdef CONFIG_FMAN_ENET
- struct dtsec *tsec = (void *)CONFIG_SYS_FSL_FM1_DTSEC1_ADDR;
struct fsl_pq_mdio_info dtsec_mdio_info;
struct tgec_mdio_info tgec_mdio_info;
unsigned int i, slot;
initialize_lane_to_slot();
- /*
- * Set TBIPA on FM1@DTSEC1. This is needed for configurations
- * where FM1@DTSEC1 isn't used directly, since it provides
- * MDIO for other ports.
- */
- out_be32(&tsec->tbipa, CONFIG_SYS_TBIPA_VALUE);
-
/* We want to use the PIXIS to configure MUX routing, not GPIOs. */
setbits_8(&pixis->brdcfg2, BRDCFG2_REG_GPIO_SEL);
{
#ifdef CONFIG_FMAN_ENET
ccsr_gpio_t *pgpio = (void *)(CONFIG_SYS_MPC85xx_GPIO_ADDR);
- struct dtsec *tsec = (void *)CONFIG_SYS_FSL_FM1_DTSEC1_ADDR;
int i;
struct fsl_pq_mdio_info dtsec_mdio_info;
struct tgec_mdio_info tgec_mdio_info;
SLOT5, /* 17 - Bank 3:D */
};
- /*
- * Set TBIPA on FM1@DTSEC1. This is needed for configurations
- * where FM1@DTSEC1 isn't used directly, since it provides
- * MDIO for other ports.
- */
- out_be32(&tsec->tbipa, CONFIG_SYS_TBIPA_VALUE);
-
/* Initialize the mdio_mux array so we can recognize empty elements */
for (i = 0; i < NUM_FM_PORTS; i++)
mdio_mux[i] = EMI_NONE;
#include <miiphy.h>
#include <libfdt.h>
#include <fdt_support.h>
+#include <tsec.h>
+#include <fsl_mdio.h>
+#include <netdev.h>
#include "../common/cadmus.h"
#include "../common/eeprom.h"
volatile fsl_lbc_t *lbc = LBC_BASE_ADDR;
uint clkdiv;
- uint lbc_hz;
sys_info_t sysinfo;
get_sys_info(&sysinfo);
clkdiv = (lbc->lcrr & LCRR_CLKDIV) * 2;
- lbc_hz = sysinfo.freqSystemBus / 1000000 / clkdiv;
gur->lbiuiplldcr1 = 0x00078080;
if (clkdiv == 16) {
uint idx;
volatile fsl_lbc_t *lbc = LBC_BASE_ADDR;
uint *sdram_addr = (uint *)CONFIG_SYS_LBC_SDRAM_BASE;
- uint cpu_board_rev;
uint lsdmr_common;
puts("LBC SDRAM: ");
/*
* MPC8548 uses "new" 15-16 style addressing.
*/
- cpu_board_rev = get_cpu_board_revision();
lsdmr_common = CONFIG_SYS_LBC_LSDMR_COMMON;
lsdmr_common |= LSDMR_BSMA1516;
fsl_pcie_init_board(first_free_busno);
}
-int last_stage_init(void)
+void configure_rgmii(void)
{
unsigned short temp;
/* This is needed to get the RGMII working for the 1.3+
* CDS cards */
if (get_board_version() == 0x13) {
- miiphy_write(CONFIG_TSEC1_NAME,
+ miiphy_write(DEFAULT_MII_NAME,
TSEC1_PHY_ADDR, 29, 18);
- miiphy_read(CONFIG_TSEC1_NAME,
+ miiphy_read(DEFAULT_MII_NAME,
TSEC1_PHY_ADDR, 30, &temp);
temp = (temp & 0xf03f);
temp |= 2 << 9; /* 36 ohm */
temp |= 2 << 6; /* 39 ohm */
- miiphy_write(CONFIG_TSEC1_NAME,
+ miiphy_write(DEFAULT_MII_NAME,
TSEC1_PHY_ADDR, 30, temp);
- miiphy_write(CONFIG_TSEC1_NAME,
+ miiphy_write(DEFAULT_MII_NAME,
TSEC1_PHY_ADDR, 29, 3);
- miiphy_write(CONFIG_TSEC1_NAME,
+ miiphy_write(DEFAULT_MII_NAME,
TSEC1_PHY_ADDR, 30, 0x8000);
}
- return 0;
+ return;
}
+#ifdef CONFIG_TSEC_ENET
+int board_eth_init(bd_t *bis)
+{
+ struct fsl_pq_mdio_info mdio_info;
+ struct tsec_info_struct tsec_info[4];
+ int num = 0;
+
+#ifdef CONFIG_TSEC1
+ SET_STD_TSEC_INFO(tsec_info[num], 1);
+ num++;
+#endif
+#ifdef CONFIG_TSEC2
+ SET_STD_TSEC_INFO(tsec_info[num], 2);
+ num++;
+#endif
+#ifdef CONFIG_TSEC3
+ /* initialize TSEC3 only if Carrier is 1.3 or above on CDS */
+ if (get_board_version() >= 0x13) {
+ SET_STD_TSEC_INFO(tsec_info[num], 3);
+ tsec_info[num].interface = PHY_INTERFACE_MODE_RGMII_ID;
+ num++;
+ }
+#endif
+#ifdef CONFIG_TSEC4
+ /* initialize TSEC4 only if Carrier is 1.3 or above on CDS */
+ if (get_board_version() >= 0x13) {
+ SET_STD_TSEC_INFO(tsec_info[num], 4);
+ tsec_info[num].interface = PHY_INTERFACE_MODE_RGMII_ID;
+ num++;
+ }
+#endif
+
+ if (!num) {
+ printf("No TSECs initialized\n");
+
+ return 0;
+ }
+
+ mdio_info.regs = (struct tsec_mii_mng *)CONFIG_SYS_MDIO_BASE_ADDR;
+ mdio_info.name = DEFAULT_MII_NAME;
+ fsl_pq_mdio_init(bis, &mdio_info);
+
+ tsec_eth_init(bis, tsec_info, num);
+ configure_rgmii();
+
+ return pci_eth_init(bis);
+}
+#endif
#if defined(CONFIG_OF_BOARD_SETUP)
void ft_pci_setup(void *blob, bd_t *bd)
volatile fsl_lbc_t *lbc = LBC_BASE_ADDR;
uint clkdiv;
- uint lbc_hz;
sys_info_t sysinfo;
get_sys_info(&sysinfo);
clkdiv = (lbc->lcrr & LCRR_CLKDIV) * 2;
- lbc_hz = sysinfo.freqSystemBus / 1000000 / clkdiv;
gur->lbiuiplldcr1 = 0x00078080;
if (clkdiv == 16) {
i2c_write(0x27, 0x3, 1, &val8, 1);
asm("eieio");
+ i2c_set_bus_num(orig_i2c_bus);
}
#ifdef CONFIG_PCI
volatile fsl_lbc_t *lbc = LBC_BASE_ADDR;
uint clkdiv;
- uint lbc_hz;
sys_info_t sysinfo;
get_sys_info(&sysinfo);
clkdiv = (lbc->lcrr & LCRR_CLKDIV) * 2;
- lbc_hz = sysinfo.freqSystemBus / 1000000 / clkdiv;
out_be32(&gur->lbiuiplldcr1, 0x00078080);
if (clkdiv == 16)
MAS3_SX|MAS3_SR, MAS2_W|MAS2_G,
0, 2, BOOKE_PAGESZ_256M, 1),
+#ifndef CONFIG_NAND_SPL
/* *I*G* - PCI */
SET_TLB_ENTRY(1, CONFIG_SYS_PCIE3_MEM_VIRT, CONFIG_SYS_PCIE3_MEM_PHYS,
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
SET_TLB_ENTRY(1, CONFIG_SYS_PCIE3_IO_VIRT, CONFIG_SYS_PCIE3_IO_PHYS,
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
0, 6, BOOKE_PAGESZ_256K, 1),
+#endif
/* *I*G - NAND */
SET_TLB_ENTRY(1, CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE_PHYS,
fdt_fixup_memory(blob, (u64)base, (u64)size);
+#if defined(CONFIG_HAS_FSL_DR_USB)
fdt_fixup_dr_usb(blob, bd);
+#endif
/* P1014 and it's derivatives don't support CAN and eTSEC3 */
if (cpu->soc_ver == SVR_P1014 || cpu->soc_ver == SVR_P1014_E) {
fdt_fixup_memory(blob, (u64)base, (u64)size);
+#if defined(CONFIG_HAS_FSL_DR_USB)
fdt_fixup_dr_usb(blob, bd);
+#endif
#if defined(CONFIG_SDCARD) || defined(CONFIG_SPIFLASH)
/* Delete eLBC node as it is muxed with USB2 controller */
#include <asm/mmu.h>
struct law_entry law_table[] = {
- SET_LAW(CONFIG_SYS_FLASH_BASE_PHYS, LAW_SIZE_64M, LAW_TRGT_IF_LBC),
+#ifndef CONFIG_NAND_SPL
SET_LAW(CONFIG_SYS_CPLD_BASE_PHYS, LAW_SIZE_1M, LAW_TRGT_IF_LBC),
SET_LAW(CONFIG_SYS_PMC_BASE_PHYS, LAW_SIZE_64K, LAW_TRGT_IF_LBC),
-#ifdef CONFIG_SYS_NAND_BASE_PHYS
- SET_LAW(CONFIG_SYS_NAND_BASE_PHYS, LAW_SIZE_1M, LAW_TRGT_IF_LBC),
-#endif
#ifdef CONFIG_VSC7385_ENET
SET_LAW(CONFIG_SYS_VSC7385_BASE_PHYS, LAW_SIZE_1M, LAW_TRGT_IF_LBC),
#endif
+#endif
+ SET_LAW(CONFIG_SYS_FLASH_BASE_PHYS, LAW_SIZE_64M, LAW_TRGT_IF_LBC),
+#ifdef CONFIG_SYS_NAND_BASE_PHYS
+ SET_LAW(CONFIG_SYS_NAND_BASE_PHYS, LAW_SIZE_1M, LAW_TRGT_IF_LBC),
+#endif
};
int num_law_entries = ARRAY_SIZE(law_table);
fdt_board_fixup_qe_pins(blob);
#endif
#endif
+
+#if defined(CONFIG_HAS_FSL_DR_USB)
fdt_fixup_dr_usb(blob, bd);
+#endif
}
#endif
int board_eth_init(bd_t *bis)
{
#ifdef CONFIG_FMAN_ENET
- struct dtsec *tsec = (void *)CONFIG_SYS_FSL_FM1_DTSEC1_ADDR;
struct fsl_pq_mdio_info dtsec_mdio_info;
struct tgec_mdio_info tgec_mdio_info;
unsigned int i, slot;
initialize_lane_to_slot();
- /*
- * Set TBIPA on FM1@DTSEC1. This is needed for configurations
- * where FM1@DTSEC1 isn't used directly, since it provides
- * MDIO for other ports.
- */
- out_be32(&tsec->tbipa, CONFIG_SYS_TBIPA_VALUE);
-
dtsec_mdio_info.regs =
(struct tsec_mii_mng *)CONFIG_SYS_FM1_DTSEC1_MDIO_ADDR;
dtsec_mdio_info.name = DEFAULT_FM_MDIO_NAME;
volatile fsl_lbc_t *lbc = LBC_BASE_ADDR;
uint clkdiv;
- uint lbc_hz;
sys_info_t sysinfo;
get_sys_info(&sysinfo);
clkdiv = (in_be32(&lbc->lcrr) & LCRR_CLKDIV) * 2;
- lbc_hz = sysinfo.freqSystemBus / 1000000 / clkdiv;
out_be32(&gur->lbiuiplldcr1, 0x00078080);
if (clkdiv == 16) {
void
ft_board_setup(void *blob, bd_t *bd)
{
- int node, tmp[2];
+ int node;
#ifdef CONFIG_PCI
const char *path;
#endif
ft_cpu_setup(blob, bd);
node = fdt_path_offset(blob, "/aliases");
- tmp[0] = 0;
if (node >= 0) {
#ifdef CONFIG_PCI
path = fdt_getprop(blob, node, "pci0", NULL);
int dev = CONFIG_SYS_MMC_ENV_DEV;
void *addr = malloc(CONFIG_SYS_FMAN_FW_LENGTH);
u32 cnt = CONFIG_SYS_FMAN_FW_LENGTH / 512;
- u32 n;
u32 blk = CONFIG_SYS_QE_FW_IN_MMC / 512;
struct mmc *mmc = find_mmc_device(CONFIG_SYS_MMC_ENV_DEV);
printf("\nMMC read: dev # %u, block # %u, count %u ...\n",
dev, blk, cnt);
mmc_init(mmc);
- n = mmc->block_dev.block_read(dev, blk, cnt, addr);
+ (void)mmc->block_dev.block_read(dev, blk, cnt, addr);
/* flush cache after read */
flush_cache((ulong)addr, cnt * 512);
}
#include <tsec.h>
#include <fsl_mdio.h>
#include <asm/errno.h>
+#include <asm/processor.h>
DECLARE_GLOBAL_DATA_PTR;
#error "rtx must be 64-bit aligned"
#endif
+static int tsec_send(struct eth_device *dev,
+ volatile void *packet, int length);
+
/* Default initializations for TSEC controllers. */
static struct tsec_info_struct tsec_info[] = {
(phydev->port == PORT_FIBRE) ? ", fiber mode" : "");
}
+#ifdef CONFIG_SYS_FSL_ERRATUM_NMG_ETSEC129
+/*
+ * When MACCFG1[Rx_EN] is enabled during system boot as part
+ * of the eTSEC port initialization sequence,
+ * the eTSEC Rx logic may not be properly initialized.
+ */
+void redundant_init(struct eth_device *dev)
+{
+ struct tsec_private *priv = dev->priv;
+ tsec_t *regs = priv->regs;
+ uint t, count = 0;
+ int fail = 1;
+ static const u8 pkt[] = {
+ 0x00, 0x1e, 0x4f, 0x12, 0xcb, 0x2c, 0x00, 0x25,
+ 0x64, 0xbb, 0xd1, 0xab, 0x08, 0x00, 0x45, 0x00,
+ 0x00, 0x5c, 0xdd, 0x22, 0x00, 0x00, 0x80, 0x01,
+ 0x1f, 0x71, 0x0a, 0xc1, 0x14, 0x22, 0x0a, 0xc1,
+ 0x14, 0x6a, 0x08, 0x00, 0xef, 0x7e, 0x02, 0x00,
+ 0x94, 0x05, 0x61, 0x62, 0x63, 0x64, 0x65, 0x66,
+ 0x67, 0x68, 0x69, 0x6a, 0x6b, 0x6c, 0x6d, 0x6e,
+ 0x6f, 0x70, 0x71, 0x72, 0x73, 0x74, 0x75, 0x76,
+ 0x77, 0x61, 0x62, 0x63, 0x64, 0x65, 0x66, 0x67,
+ 0x68, 0x69, 0x6a, 0x6b, 0x6c, 0x6d, 0x6e, 0x6f,
+ 0x70, 0x71, 0x72, 0x73, 0x74, 0x75, 0x76, 0x77,
+ 0x61, 0x62, 0x63, 0x64, 0x65, 0x66, 0x67, 0x68,
+ 0x69, 0x6a, 0x6b, 0x6c, 0x6d, 0x6e, 0x6f, 0x70,
+ 0x71, 0x72};
+
+ /* Enable promiscuous mode */
+ setbits_be32(®s->rctrl, 0x8);
+ /* Enable loopback mode */
+ setbits_be32(®s->maccfg1, MACCFG1_LOOPBACK);
+ /* Enable transmit and receive */
+ setbits_be32(®s->maccfg1, MACCFG1_RX_EN | MACCFG1_TX_EN);
+
+ /* Tell the DMA it is clear to go */
+ setbits_be32(®s->dmactrl, DMACTRL_INIT_SETTINGS);
+ out_be32(®s->tstat, TSTAT_CLEAR_THALT);
+ out_be32(®s->rstat, RSTAT_CLEAR_RHALT);
+ clrbits_be32(®s->dmactrl, DMACTRL_GRS | DMACTRL_GTS);
+
+ do {
+ tsec_send(dev, (void *)pkt, sizeof(pkt));
+
+ /* Wait for buffer to be received */
+ for (t = 0; rtx.rxbd[rxIdx].status & RXBD_EMPTY; t++) {
+ if (t >= 10 * TOUT_LOOP) {
+ printf("%s: tsec: rx error\n", dev->name);
+ break;
+ }
+ }
+
+ if (!memcmp(pkt, (void *)NetRxPackets[rxIdx], sizeof(pkt)))
+ fail = 0;
+
+ rtx.rxbd[rxIdx].length = 0;
+ rtx.rxbd[rxIdx].status =
+ RXBD_EMPTY | (((rxIdx + 1) == PKTBUFSRX) ? RXBD_WRAP : 0);
+ rxIdx = (rxIdx + 1) % PKTBUFSRX;
+
+ if (in_be32(®s->ievent) & IEVENT_BSY) {
+ out_be32(®s->ievent, IEVENT_BSY);
+ out_be32(®s->rstat, RSTAT_CLEAR_RHALT);
+ }
+ if (fail) {
+ printf("loopback recv packet error!\n");
+ clrbits_be32(®s->maccfg1, MACCFG1_RX_EN);
+ udelay(1000);
+ setbits_be32(®s->maccfg1, MACCFG1_RX_EN);
+ }
+ } while ((count++ < 4) && (fail == 1));
+
+ if (fail)
+ panic("eTSEC init fail!\n");
+ /* Disable promiscuous mode */
+ clrbits_be32(®s->rctrl, 0x8);
+ /* Disable loopback mode */
+ clrbits_be32(®s->maccfg1, MACCFG1_LOOPBACK);
+}
+#endif
+
/* Set up the buffers and their descriptors, and bring up the
* interface
*/
/* reset the indices to zero */
rxIdx = 0;
txIdx = 0;
+#ifdef CONFIG_SYS_FSL_ERRATUM_NMG_ETSEC129
+ uint svr;
+#endif
/* Point to the buffer descriptors */
out_be32(®s->tbase, (unsigned int)(&rtx.txbd[txIdx]));
}
rtx.txbd[TX_BUF_CNT - 1].status |= TXBD_WRAP;
+#ifdef CONFIG_SYS_FSL_ERRATUM_NMG_ETSEC129
+ svr = get_svr();
+ if ((SVR_MAJ(svr) == 1) || IS_SVR_REV(svr, 2, 0))
+ redundant_init(dev);
+#endif
/* Enable Transmit and Receive */
setbits_be32(®s->maccfg1, MACCFG1_RX_EN | MACCFG1_TX_EN);
static int uec_stop(uec_private_t *uec, comm_dir_e mode)
{
- ucc_fast_private_t *uccf;
-
if (!uec || !uec->uccf) {
printf("%s: No handle passed.\n", __FUNCTION__);
return -EINVAL;
}
- uccf = uec->uccf;
/* check if the UCC number is in range. */
if (uec->uec_info->uf_info.ucc_num >= UCC_MAX_NUM) {
phy_interface_t if_mode, int speed)
{
phy_interface_t enet_if_mode;
- uec_info_t *uec_info;
uec_t *uec_regs;
u32 upsmr;
u32 maccfg2;
return -EINVAL;
}
- uec_info = uec->uec_info;
uec_regs = uec->uec_regs;
enet_if_mode = if_mode;
static void adjust_link(struct eth_device *dev)
{
uec_private_t *uec = (uec_private_t *)dev->priv;
- uec_t *uec_regs;
struct uec_mii_info *mii_info = uec->mii_info;
extern void change_phy_interface_mode(struct eth_device *dev,
phy_interface_t mode, int speed);
- uec_regs = uec->uec_regs;
if (mii_info->link) {
/* Now we make sure that we can be in full duplex mode.
int ehci_hcd_init(void)
{
struct usb_ehci *ehci;
- char usb_phy[5];
const char *phy_type = NULL;
size_t len;
+#ifdef CONFIG_SYS_FSL_USB_INTERNAL_UTMI_PHY
+ char usb_phy[5];
usb_phy[0] = '\0';
+#endif
ehci = (struct usb_ehci *)CONFIG_SYS_FSL_USB_ADDR;
hccr = (struct ehci_hccr *)((uint32_t)&ehci->caplength);
#define CONFIG_PHY_REALTEK
#define CONFIG_PHY_NATSEMI
#define CONFIG_PHY_LXT
+#define CONFIG_PHY_ATHEROS
#ifdef CONFIG_PHYLIB_10G
#define CONFIG_PHY_TERANETICS
#define CONFIG_SYS_CCSRBAR 0xffe00000
#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
-#if defined(CONFIG_RAMBOOT_NAND) && !defined(CONFIG_NAND_SPL)
+#if defined(CONFIG_NAND_SPL)
#define CONFIG_SYS_CCSR_DO_NOT_RELOCATE
#endif
#define CONFIG_TSEC4_NAME "eTSEC3"
#undef CONFIG_MPC85XX_FEC
+#define CONFIG_PHY_MARVELL
+
#define TSEC1_PHY_ADDR 0
#define TSEC2_PHY_ADDR 1
#define TSEC3_PHY_ADDR 2
#define CONFIG_SYS_CCSRBAR 0xe0000000
#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
-#if defined(CONFIG_RAMBOOT_NAND) && !defined(CONFIG_NAND_SPL)
+#if defined(CONFIG_NAND_SPL)
#define CONFIG_SYS_CCSR_DO_NOT_RELOCATE
#endif
#define CONFIG_SYS_CCSRBAR 0xffe00000
#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
-#if defined(CONFIG_RAMBOOT_NAND) && !defined(CONFIG_NAND_SPL)
+#if defined(CONFIG_NAND_SPL)
#define CONFIG_SYS_CCSR_DO_NOT_RELOCATE
#endif
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
#define CONFIG_SYS_MONITOR_LEN (512 * 1024)
-#define CONFIG_SYS_MALLOC_LEN (6 * 1024 * 1024)
+#define CONFIG_SYS_MALLOC_LEN (10 * 1024 * 1024)
/*
* Serial Port
#define CONFIG_SYS_CCSRBAR 0xffe00000
#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
-#if defined(CONFIG_RAMBOOT_NAND) && !defined(CONFIG_NAND_SPL)
+#if defined(CONFIG_NAND_SPL)
#define CONFIG_SYS_CCSR_DO_NOT_RELOCATE
#endif
/* IN case of NAND bootloader relocate CCSRBAR in RAMboot code not in the 4k
SPL code*/
-#if defined(CONFIG_NAND_U_BOOT) && defined(CONFIG_NAND_SPL)
+#if defined(CONFIG_NAND_SPL)
#define CONFIG_SYS_CCSR_DO_NOT_RELOCATE
#endif
projects / platform / kernel / u-boot.git / commitdiff