- requirements for booting
Interrupts
- ARM Interrupt subsystem documentation
-IXP2000
- - Release Notes for Linux on Intel's IXP2000 Network Processor
msm
- MSM specific documentation
Netwinder
+++ /dev/null
-
--------------------------------------------------------------------------
-Release Notes for Linux on Intel's IXP2000 Network Processor
-
-Maintained by Deepak Saxena <dsaxena@plexity.net>
--------------------------------------------------------------------------
-
-1. Overview
-
-Intel's IXP2000 family of NPUs (IXP2400, IXP2800, IXP2850) is designed
-for high-performance network applications such high-availability
-telecom systems. In addition to an XScale core, it contains up to 8
-"MicroEngines" that run special code, several high-end networking
-interfaces (UTOPIA, SPI, etc), a PCI host bridge, one serial port,
-flash interface, and some other odds and ends. For more information, see:
-
-http://developer.intel.com
-
-2. Linux Support
-
-Linux currently supports the following features on the IXP2000 NPUs:
-
-- On-chip serial
-- PCI
-- Flash (MTD/JFFS2)
-- I2C through GPIO
-- Timers (watchdog, OS)
-
-That is about all we can support under Linux ATM b/c the core networking
-components of the chip are accessed via Intel's closed source SDK.
-Please contact Intel directly on issues with using those. There is
-also a mailing list run by some folks at Princeton University that might
-be of help: https://lists.cs.princeton.edu/mailman/listinfo/ixp2xxx
-
-WHATEVER YOU DO, DO NOT POST EMAIL TO THE LINUX-ARM OR LINUX-ARM-KERNEL
-MAILING LISTS REGARDING THE INTEL SDK.
-
-3. Supported Platforms
-
-- Intel IXDP2400 Reference Platform
-- Intel IXDP2800 Reference Platform
-- Intel IXDP2401 Reference Platform
-- Intel IXDP2801 Reference Platform
-- RadiSys ENP-2611
-
-4. Usage Notes
-
-- The IXP2000 platforms usually have rather complex PCI bus topologies
- with large memory space requirements. In addition, b/c of the way the
- Intel SDK is designed, devices are enumerated in a very specific
- way. B/c of this this, we use "pci=firmware" option in the kernel
- command line so that we do not re-enumerate the bus.
-
-- IXDP2x01 systems have variable clock tick rates that we cannot determine
- via HW registers. The "ixdp2x01_clk=XXX" cmd line options allow you
- to pass the clock rate to the board port.
-
-5. Thanks
-
-The IXP2000 work has been funded by Intel Corp. and MontaVista Software, Inc.
-
-The following people have contributed patches/comments/etc:
-
-Naeem F. Afzal
-Lennert Buytenhek
-Jeffrey Daly
-
--------------------------------------------------------------------------
-Last Update: 8/09/2004
F: drivers/amba/
F: include/linux/amba/bus.h
-ARM/ADI ROADRUNNER MACHINE SUPPORT
-M: Lennert Buytenhek <kernel@wantstofly.org>
-L: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
-S: Maintained
-F: arch/arm/mach-ixp23xx/
-F: arch/arm/mach-ixp23xx/include/mach/
-
ARM/ADS SPHERE MACHINE SUPPORT
M: Lennert Buytenhek <kernel@wantstofly.org>
L: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
L: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
S: Maintained
-ARM/INTEL IXP2000 ARM ARCHITECTURE
-M: Lennert Buytenhek <kernel@wantstofly.org>
-L: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
-S: Maintained
-
ARM/INTEL IXDP2850 MACHINE SUPPORT
M: Lennert Buytenhek <kernel@wantstofly.org>
L: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
S: Maintained
-ARM/INTEL IXP23XX ARM ARCHITECTURE
-M: Lennert Buytenhek <kernel@wantstofly.org>
-L: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
-S: Maintained
-
ARM/INTEL IXP4XX ARM ARCHITECTURE
M: Imre Kaloz <kaloz@openwrt.org>
M: Krzysztof Halasa <khc@pm.waw.pl>
help
Support for Intel's IOP33X (XScale) family of processors.
-config ARCH_IXP23XX
- bool "IXP23XX-based"
- depends on MMU
- select CPU_XSC3
- select PCI
- select ARCH_USES_GETTIMEOFFSET
- select NEED_MACH_IO_H
- select NEED_MACH_MEMORY_H
- help
- Support for Intel's IXP23xx (XScale) family of processors.
-
-config ARCH_IXP2000
- bool "IXP2400/2800-based"
- depends on MMU
- select CPU_XSCALE
- select PCI
- select ARCH_USES_GETTIMEOFFSET
- select NEED_MACH_IO_H
- select NEED_MACH_MEMORY_H
- help
- Support for Intel's IXP2400/2800 (XScale) family of processors.
-
config ARCH_IXP4XX
bool "IXP4xx-based"
depends on MMU
source "arch/arm/mach-ixp4xx/Kconfig"
-source "arch/arm/mach-ixp2000/Kconfig"
-
-source "arch/arm/mach-ixp23xx/Kconfig"
-
source "arch/arm/mach-kirkwood/Kconfig"
source "arch/arm/mach-ks8695/Kconfig"
machine-$(CONFIG_ARCH_IOP13XX) := iop13xx
machine-$(CONFIG_ARCH_IOP32X) := iop32x
machine-$(CONFIG_ARCH_IOP33X) := iop33x
-machine-$(CONFIG_ARCH_IXP2000) := ixp2000
-machine-$(CONFIG_ARCH_IXP23XX) := ixp23xx
machine-$(CONFIG_ARCH_IXP4XX) := ixp4xx
machine-$(CONFIG_ARCH_KIRKWOOD) := kirkwood
machine-$(CONFIG_ARCH_KS8695) := ks8695
bic r0, r0, #0x1000 @ clear Icache
mcr p15, 0, r0, c1, c0, 0
-#ifdef CONFIG_ARCH_IXP2000
- mov r1, #-1
- mov r0, #0xd6000000
- str r1, [r0, #0x14]
- str r1, [r0, #0x18]
-#endif
-
obj-$(CONFIG_SHARP_LOCOMO) += locomo.o
obj-$(CONFIG_SHARP_PARAM) += sharpsl_param.o
obj-$(CONFIG_SHARP_SCOOP) += scoop.o
-obj-$(CONFIG_ARCH_IXP2000) += uengine.o
-obj-$(CONFIG_ARCH_IXP23XX) += uengine.o
obj-$(CONFIG_PCI_HOST_ITE8152) += it8152.o
obj-$(CONFIG_ARM_TIMER_SP804) += timer-sp.o
+++ /dev/null
-/*
- * Generic library functions for the microengines found on the Intel
- * IXP2000 series of network processors.
- *
- * Copyright (C) 2004, 2005 Lennert Buytenhek <buytenh@wantstofly.org>
- * Dedicated to Marija Kulikova.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU Lesser General Public License as
- * published by the Free Software Foundation; either version 2.1 of the
- * License, or (at your option) any later version.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/slab.h>
-#include <linux/module.h>
-#include <linux/string.h>
-#include <linux/io.h>
-#include <mach/hardware.h>
-#include <asm/hardware/uengine.h>
-
-#if defined(CONFIG_ARCH_IXP2000)
-#define IXP_UENGINE_CSR_VIRT_BASE IXP2000_UENGINE_CSR_VIRT_BASE
-#define IXP_PRODUCT_ID IXP2000_PRODUCT_ID
-#define IXP_MISC_CONTROL IXP2000_MISC_CONTROL
-#define IXP_RESET1 IXP2000_RESET1
-#else
-#if defined(CONFIG_ARCH_IXP23XX)
-#define IXP_UENGINE_CSR_VIRT_BASE IXP23XX_UENGINE_CSR_VIRT_BASE
-#define IXP_PRODUCT_ID IXP23XX_PRODUCT_ID
-#define IXP_MISC_CONTROL IXP23XX_MISC_CONTROL
-#define IXP_RESET1 IXP23XX_RESET1
-#else
-#error unknown platform
-#endif
-#endif
-
-#define USTORE_ADDRESS 0x000
-#define USTORE_DATA_LOWER 0x004
-#define USTORE_DATA_UPPER 0x008
-#define CTX_ENABLES 0x018
-#define CC_ENABLE 0x01c
-#define CSR_CTX_POINTER 0x020
-#define INDIRECT_CTX_STS 0x040
-#define ACTIVE_CTX_STS 0x044
-#define INDIRECT_CTX_SIG_EVENTS 0x048
-#define INDIRECT_CTX_WAKEUP_EVENTS 0x050
-#define NN_PUT 0x080
-#define NN_GET 0x084
-#define TIMESTAMP_LOW 0x0c0
-#define TIMESTAMP_HIGH 0x0c4
-#define T_INDEX_BYTE_INDEX 0x0f4
-#define LOCAL_CSR_STATUS 0x180
-
-u32 ixp2000_uengine_mask;
-
-static void *ixp2000_uengine_csr_area(int uengine)
-{
- return ((void *)IXP_UENGINE_CSR_VIRT_BASE) + (uengine << 10);
-}
-
-/*
- * LOCAL_CSR_STATUS=1 after a read or write to a microengine's CSR
- * space means that the microengine we tried to access was also trying
- * to access its own CSR space on the same clock cycle as we did. When
- * this happens, we lose the arbitration process by default, and the
- * read or write we tried to do was not actually performed, so we try
- * again until it succeeds.
- */
-u32 ixp2000_uengine_csr_read(int uengine, int offset)
-{
- void *uebase;
- u32 *local_csr_status;
- u32 *reg;
- u32 value;
-
- uebase = ixp2000_uengine_csr_area(uengine);
-
- local_csr_status = (u32 *)(uebase + LOCAL_CSR_STATUS);
- reg = (u32 *)(uebase + offset);
- do {
- value = ixp2000_reg_read(reg);
- } while (ixp2000_reg_read(local_csr_status) & 1);
-
- return value;
-}
-EXPORT_SYMBOL(ixp2000_uengine_csr_read);
-
-void ixp2000_uengine_csr_write(int uengine, int offset, u32 value)
-{
- void *uebase;
- u32 *local_csr_status;
- u32 *reg;
-
- uebase = ixp2000_uengine_csr_area(uengine);
-
- local_csr_status = (u32 *)(uebase + LOCAL_CSR_STATUS);
- reg = (u32 *)(uebase + offset);
- do {
- ixp2000_reg_write(reg, value);
- } while (ixp2000_reg_read(local_csr_status) & 1);
-}
-EXPORT_SYMBOL(ixp2000_uengine_csr_write);
-
-void ixp2000_uengine_reset(u32 uengine_mask)
-{
- u32 value;
-
- value = ixp2000_reg_read(IXP_RESET1) & ~ixp2000_uengine_mask;
-
- uengine_mask &= ixp2000_uengine_mask;
- ixp2000_reg_wrb(IXP_RESET1, value | uengine_mask);
- ixp2000_reg_wrb(IXP_RESET1, value);
-}
-EXPORT_SYMBOL(ixp2000_uengine_reset);
-
-void ixp2000_uengine_set_mode(int uengine, u32 mode)
-{
- /*
- * CTL_STR_PAR_EN: unconditionally enable parity checking on
- * control store.
- */
- mode |= 0x10000000;
- ixp2000_uengine_csr_write(uengine, CTX_ENABLES, mode);
-
- /*
- * Enable updating of condition codes.
- */
- ixp2000_uengine_csr_write(uengine, CC_ENABLE, 0x00002000);
-
- /*
- * Initialise other per-microengine registers.
- */
- ixp2000_uengine_csr_write(uengine, NN_PUT, 0x00);
- ixp2000_uengine_csr_write(uengine, NN_GET, 0x00);
- ixp2000_uengine_csr_write(uengine, T_INDEX_BYTE_INDEX, 0);
-}
-EXPORT_SYMBOL(ixp2000_uengine_set_mode);
-
-static int make_even_parity(u32 x)
-{
- return hweight32(x) & 1;
-}
-
-static void ustore_write(int uengine, u64 insn)
-{
- /*
- * Generate even parity for top and bottom 20 bits.
- */
- insn |= (u64)make_even_parity((insn >> 20) & 0x000fffff) << 41;
- insn |= (u64)make_even_parity(insn & 0x000fffff) << 40;
-
- /*
- * Write to microstore. The second write auto-increments
- * the USTORE_ADDRESS index register.
- */
- ixp2000_uengine_csr_write(uengine, USTORE_DATA_LOWER, (u32)insn);
- ixp2000_uengine_csr_write(uengine, USTORE_DATA_UPPER, (u32)(insn >> 32));
-}
-
-void ixp2000_uengine_load_microcode(int uengine, u8 *ucode, int insns)
-{
- int i;
-
- /*
- * Start writing to microstore at address 0.
- */
- ixp2000_uengine_csr_write(uengine, USTORE_ADDRESS, 0x80000000);
- for (i = 0; i < insns; i++) {
- u64 insn;
-
- insn = (((u64)ucode[0]) << 32) |
- (((u64)ucode[1]) << 24) |
- (((u64)ucode[2]) << 16) |
- (((u64)ucode[3]) << 8) |
- ((u64)ucode[4]);
- ucode += 5;
-
- ustore_write(uengine, insn);
- }
-
- /*
- * Pad with a few NOPs at the end (to avoid the microengine
- * aborting as it prefetches beyond the last instruction), unless
- * we run off the end of the instruction store first, at which
- * point the address register will wrap back to zero.
- */
- for (i = 0; i < 4; i++) {
- u32 addr;
-
- addr = ixp2000_uengine_csr_read(uengine, USTORE_ADDRESS);
- if (addr == 0x80000000)
- break;
- ustore_write(uengine, 0xf0000c0300ULL);
- }
-
- /*
- * End programming.
- */
- ixp2000_uengine_csr_write(uengine, USTORE_ADDRESS, 0x00000000);
-}
-EXPORT_SYMBOL(ixp2000_uengine_load_microcode);
-
-void ixp2000_uengine_init_context(int uengine, int context, int pc)
-{
- /*
- * Select the right context for indirect access.
- */
- ixp2000_uengine_csr_write(uengine, CSR_CTX_POINTER, context);
-
- /*
- * Initialise signal masks to immediately go to Ready state.
- */
- ixp2000_uengine_csr_write(uengine, INDIRECT_CTX_SIG_EVENTS, 1);
- ixp2000_uengine_csr_write(uengine, INDIRECT_CTX_WAKEUP_EVENTS, 1);
-
- /*
- * Set program counter.
- */
- ixp2000_uengine_csr_write(uengine, INDIRECT_CTX_STS, pc);
-}
-EXPORT_SYMBOL(ixp2000_uengine_init_context);
-
-void ixp2000_uengine_start_contexts(int uengine, u8 ctx_mask)
-{
- u32 mask;
-
- /*
- * Enable the specified context to go to Executing state.
- */
- mask = ixp2000_uengine_csr_read(uengine, CTX_ENABLES);
- mask |= ctx_mask << 8;
- ixp2000_uengine_csr_write(uengine, CTX_ENABLES, mask);
-}
-EXPORT_SYMBOL(ixp2000_uengine_start_contexts);
-
-void ixp2000_uengine_stop_contexts(int uengine, u8 ctx_mask)
-{
- u32 mask;
-
- /*
- * Disable the Ready->Executing transition. Note that this
- * does not stop the context until it voluntarily yields.
- */
- mask = ixp2000_uengine_csr_read(uengine, CTX_ENABLES);
- mask &= ~(ctx_mask << 8);
- ixp2000_uengine_csr_write(uengine, CTX_ENABLES, mask);
-}
-EXPORT_SYMBOL(ixp2000_uengine_stop_contexts);
-
-static int check_ixp_type(struct ixp2000_uengine_code *c)
-{
- u32 product_id;
- u32 rev;
-
- product_id = ixp2000_reg_read(IXP_PRODUCT_ID);
- if (((product_id >> 16) & 0x1f) != 0)
- return 0;
-
- switch ((product_id >> 8) & 0xff) {
-#ifdef CONFIG_ARCH_IXP2000
- case 0: /* IXP2800 */
- if (!(c->cpu_model_bitmask & 4))
- return 0;
- break;
-
- case 1: /* IXP2850 */
- if (!(c->cpu_model_bitmask & 8))
- return 0;
- break;
-
- case 2: /* IXP2400 */
- if (!(c->cpu_model_bitmask & 2))
- return 0;
- break;
-#endif
-
-#ifdef CONFIG_ARCH_IXP23XX
- case 4: /* IXP23xx */
- if (!(c->cpu_model_bitmask & 0x3f0))
- return 0;
- break;
-#endif
-
- default:
- return 0;
- }
-
- rev = product_id & 0xff;
- if (rev < c->cpu_min_revision || rev > c->cpu_max_revision)
- return 0;
-
- return 1;
-}
-
-static void generate_ucode(u8 *ucode, u32 *gpr_a, u32 *gpr_b)
-{
- int offset;
- int i;
-
- offset = 0;
-
- for (i = 0; i < 128; i++) {
- u8 b3;
- u8 b2;
- u8 b1;
- u8 b0;
-
- b3 = (gpr_a[i] >> 24) & 0xff;
- b2 = (gpr_a[i] >> 16) & 0xff;
- b1 = (gpr_a[i] >> 8) & 0xff;
- b0 = gpr_a[i] & 0xff;
-
- /* immed[@ai, (b1 << 8) | b0] */
- /* 11110000 0000VVVV VVVV11VV VVVVVV00 1IIIIIII */
- ucode[offset++] = 0xf0;
- ucode[offset++] = (b1 >> 4);
- ucode[offset++] = (b1 << 4) | 0x0c | (b0 >> 6);
- ucode[offset++] = (b0 << 2);
- ucode[offset++] = 0x80 | i;
-
- /* immed_w1[@ai, (b3 << 8) | b2] */
- /* 11110100 0100VVVV VVVV11VV VVVVVV00 1IIIIIII */
- ucode[offset++] = 0xf4;
- ucode[offset++] = 0x40 | (b3 >> 4);
- ucode[offset++] = (b3 << 4) | 0x0c | (b2 >> 6);
- ucode[offset++] = (b2 << 2);
- ucode[offset++] = 0x80 | i;
- }
-
- for (i = 0; i < 128; i++) {
- u8 b3;
- u8 b2;
- u8 b1;
- u8 b0;
-
- b3 = (gpr_b[i] >> 24) & 0xff;
- b2 = (gpr_b[i] >> 16) & 0xff;
- b1 = (gpr_b[i] >> 8) & 0xff;
- b0 = gpr_b[i] & 0xff;
-
- /* immed[@bi, (b1 << 8) | b0] */
- /* 11110000 0000VVVV VVVV001I IIIIII11 VVVVVVVV */
- ucode[offset++] = 0xf0;
- ucode[offset++] = (b1 >> 4);
- ucode[offset++] = (b1 << 4) | 0x02 | (i >> 6);
- ucode[offset++] = (i << 2) | 0x03;
- ucode[offset++] = b0;
-
- /* immed_w1[@bi, (b3 << 8) | b2] */
- /* 11110100 0100VVVV VVVV001I IIIIII11 VVVVVVVV */
- ucode[offset++] = 0xf4;
- ucode[offset++] = 0x40 | (b3 >> 4);
- ucode[offset++] = (b3 << 4) | 0x02 | (i >> 6);
- ucode[offset++] = (i << 2) | 0x03;
- ucode[offset++] = b2;
- }
-
- /* ctx_arb[kill] */
- ucode[offset++] = 0xe0;
- ucode[offset++] = 0x00;
- ucode[offset++] = 0x01;
- ucode[offset++] = 0x00;
- ucode[offset++] = 0x00;
-}
-
-static int set_initial_registers(int uengine, struct ixp2000_uengine_code *c)
-{
- int per_ctx_regs;
- u32 *gpr_a;
- u32 *gpr_b;
- u8 *ucode;
- int i;
-
- gpr_a = kzalloc(128 * sizeof(u32), GFP_KERNEL);
- gpr_b = kzalloc(128 * sizeof(u32), GFP_KERNEL);
- ucode = kmalloc(513 * 5, GFP_KERNEL);
- if (gpr_a == NULL || gpr_b == NULL || ucode == NULL) {
- kfree(ucode);
- kfree(gpr_b);
- kfree(gpr_a);
- return 1;
- }
-
- per_ctx_regs = 16;
- if (c->uengine_parameters & IXP2000_UENGINE_4_CONTEXTS)
- per_ctx_regs = 32;
-
- for (i = 0; i < 256; i++) {
- struct ixp2000_reg_value *r = c->initial_reg_values + i;
- u32 *bank;
- int inc;
- int j;
-
- if (r->reg == -1)
- break;
-
- bank = (r->reg & 0x400) ? gpr_b : gpr_a;
- inc = (r->reg & 0x80) ? 128 : per_ctx_regs;
-
- j = r->reg & 0x7f;
- while (j < 128) {
- bank[j] = r->value;
- j += inc;
- }
- }
-
- generate_ucode(ucode, gpr_a, gpr_b);
- ixp2000_uengine_load_microcode(uengine, ucode, 513);
- ixp2000_uengine_init_context(uengine, 0, 0);
- ixp2000_uengine_start_contexts(uengine, 0x01);
- for (i = 0; i < 100; i++) {
- u32 status;
-
- status = ixp2000_uengine_csr_read(uengine, ACTIVE_CTX_STS);
- if (!(status & 0x80000000))
- break;
- }
- ixp2000_uengine_stop_contexts(uengine, 0x01);
-
- kfree(ucode);
- kfree(gpr_b);
- kfree(gpr_a);
-
- return !!(i == 100);
-}
-
-int ixp2000_uengine_load(int uengine, struct ixp2000_uengine_code *c)
-{
- int ctx;
-
- if (!check_ixp_type(c))
- return 1;
-
- if (!(ixp2000_uengine_mask & (1 << uengine)))
- return 1;
-
- ixp2000_uengine_reset(1 << uengine);
- ixp2000_uengine_set_mode(uengine, c->uengine_parameters);
- if (set_initial_registers(uengine, c))
- return 1;
- ixp2000_uengine_load_microcode(uengine, c->insns, c->num_insns);
-
- for (ctx = 0; ctx < 8; ctx++)
- ixp2000_uengine_init_context(uengine, ctx, 0);
-
- return 0;
-}
-EXPORT_SYMBOL(ixp2000_uengine_load);
-
-
-static int __init ixp2000_uengine_init(void)
-{
- int uengine;
- u32 value;
-
- /*
- * Determine number of microengines present.
- */
- switch ((ixp2000_reg_read(IXP_PRODUCT_ID) >> 8) & 0x1fff) {
-#ifdef CONFIG_ARCH_IXP2000
- case 0: /* IXP2800 */
- case 1: /* IXP2850 */
- ixp2000_uengine_mask = 0x00ff00ff;
- break;
-
- case 2: /* IXP2400 */
- ixp2000_uengine_mask = 0x000f000f;
- break;
-#endif
-
-#ifdef CONFIG_ARCH_IXP23XX
- case 4: /* IXP23xx */
- ixp2000_uengine_mask = (*IXP23XX_EXP_CFG_FUSE >> 8) & 0xf;
- break;
-#endif
-
- default:
- printk(KERN_INFO "Detected unknown IXP2000 model (%.8x)\n",
- (unsigned int)ixp2000_reg_read(IXP_PRODUCT_ID));
- ixp2000_uengine_mask = 0x00000000;
- break;
- }
-
- /*
- * Reset microengines.
- */
- ixp2000_uengine_reset(ixp2000_uengine_mask);
-
- /*
- * Synchronise timestamp counters across all microengines.
- */
- value = ixp2000_reg_read(IXP_MISC_CONTROL);
- ixp2000_reg_wrb(IXP_MISC_CONTROL, value & ~0x80);
- for (uengine = 0; uengine < 32; uengine++) {
- if (ixp2000_uengine_mask & (1 << uengine)) {
- ixp2000_uengine_csr_write(uengine, TIMESTAMP_LOW, 0);
- ixp2000_uengine_csr_write(uengine, TIMESTAMP_HIGH, 0);
- }
- }
- ixp2000_reg_wrb(IXP_MISC_CONTROL, value | 0x80);
-
- return 0;
-}
-
-subsys_initcall(ixp2000_uengine_init);
+++ /dev/null
-CONFIG_EXPERIMENTAL=y
-CONFIG_SYSVIPC=y
-CONFIG_BSD_PROCESS_ACCT=y
-CONFIG_LOG_BUF_SHIFT=14
-CONFIG_BLK_DEV_INITRD=y
-CONFIG_EXPERT=y
-# CONFIG_HOTPLUG is not set
-CONFIG_SLAB=y
-CONFIG_MODULES=y
-CONFIG_MODULE_UNLOAD=y
-CONFIG_ARCH_IXP2000=y
-CONFIG_ARCH_ENP2611=y
-CONFIG_ARCH_IXDP2400=y
-CONFIG_ARCH_IXDP2800=y
-CONFIG_ARCH_IXDP2401=y
-CONFIG_ARCH_IXDP2801=y
-# CONFIG_IXP2000_SUPPORT_BROKEN_PCI_IO is not set
-# CONFIG_ARM_THUMB is not set
-CONFIG_CPU_BIG_ENDIAN=y
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZBOOT_ROM_BSS=0x0
-CONFIG_CMDLINE="console=ttyS0,57600 root=/dev/nfs ip=bootp mem=64M@0x0"
-CONFIG_FPE_NWFPE=y
-CONFIG_FPE_NWFPE_XP=y
-CONFIG_NET=y
-CONFIG_PACKET=y
-CONFIG_UNIX=y
-CONFIG_INET=y
-CONFIG_IP_PNP=y
-CONFIG_IP_PNP_DHCP=y
-CONFIG_IP_PNP_BOOTP=y
-CONFIG_SYN_COOKIES=y
-CONFIG_IPV6=y
-# CONFIG_INET6_XFRM_MODE_TRANSPORT is not set
-# CONFIG_INET6_XFRM_MODE_TUNNEL is not set
-# CONFIG_INET6_XFRM_MODE_BEET is not set
-# CONFIG_IPV6_SIT is not set
-# CONFIG_PREVENT_FIRMWARE_BUILD is not set
-CONFIG_MTD=y
-CONFIG_MTD_PARTITIONS=y
-CONFIG_MTD_REDBOOT_PARTS=y
-CONFIG_MTD_REDBOOT_PARTS_UNALLOCATED=y
-CONFIG_MTD_REDBOOT_PARTS_READONLY=y
-CONFIG_MTD_CHAR=y
-CONFIG_MTD_BLOCK=y
-CONFIG_MTD_CFI=y
-CONFIG_MTD_CFI_INTELEXT=y
-CONFIG_MTD_COMPLEX_MAPPINGS=y
-CONFIG_MTD_IXP2000=y
-CONFIG_BLK_DEV_LOOP=y
-CONFIG_BLK_DEV_NBD=y
-CONFIG_BLK_DEV_RAM=y
-CONFIG_BLK_DEV_RAM_SIZE=8192
-CONFIG_EEPROM_LEGACY=y
-CONFIG_NETDEVICES=y
-CONFIG_DUMMY=y
-CONFIG_NET_ETHERNET=y
-CONFIG_NET_PCI=y
-CONFIG_CS89x0=y
-CONFIG_E100=y
-CONFIG_ENP2611_MSF_NET=y
-CONFIG_WAN=y
-CONFIG_HDLC=y
-CONFIG_HDLC_RAW=y
-CONFIG_HDLC_CISCO=y
-CONFIG_HDLC_FR=y
-CONFIG_HDLC_PPP=y
-CONFIG_DLCI=y
-# CONFIG_INPUT_KEYBOARD is not set
-# CONFIG_INPUT_MOUSE is not set
-# CONFIG_SERIO is not set
-# CONFIG_VT is not set
-CONFIG_SERIAL_8250=y
-CONFIG_SERIAL_8250_CONSOLE=y
-CONFIG_SERIAL_8250_NR_UARTS=3
-# CONFIG_HW_RANDOM is not set
-CONFIG_I2C=y
-CONFIG_I2C_CHARDEV=y
-CONFIG_I2C_IXP2000=y
-CONFIG_WATCHDOG=y
-CONFIG_IXP2000_WATCHDOG=y
-CONFIG_EXT2_FS=y
-CONFIG_EXT2_FS_XATTR=y
-CONFIG_EXT2_FS_POSIX_ACL=y
-CONFIG_EXT3_FS=y
-CONFIG_EXT3_FS_POSIX_ACL=y
-CONFIG_INOTIFY=y
-CONFIG_TMPFS=y
-CONFIG_JFFS2_FS=y
-CONFIG_NFS_FS=y
-CONFIG_NFS_V3=y
-CONFIG_ROOT_NFS=y
-CONFIG_PARTITION_ADVANCED=y
-CONFIG_MAGIC_SYSRQ=y
-CONFIG_DEBUG_KERNEL=y
-CONFIG_DEBUG_MUTEXES=y
-CONFIG_DEBUG_USER=y
-CONFIG_DEBUG_ERRORS=y
-CONFIG_DEBUG_LL=y
+++ /dev/null
-CONFIG_EXPERIMENTAL=y
-CONFIG_SYSVIPC=y
-CONFIG_BSD_PROCESS_ACCT=y
-CONFIG_LOG_BUF_SHIFT=14
-CONFIG_BLK_DEV_INITRD=y
-CONFIG_EXPERT=y
-CONFIG_SLAB=y
-CONFIG_MODULES=y
-CONFIG_MODULE_UNLOAD=y
-CONFIG_ARCH_IXP23XX=y
-CONFIG_MACH_ESPRESSO=y
-CONFIG_MACH_IXDP2351=y
-CONFIG_MACH_ROADRUNNER=y
-# CONFIG_ARM_THUMB is not set
-CONFIG_CPU_BIG_ENDIAN=y
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZBOOT_ROM_BSS=0x0
-CONFIG_CMDLINE="console=ttyS0,115200 root=/dev/nfs ip=bootp"
-CONFIG_FPE_NWFPE=y
-CONFIG_FPE_NWFPE_XP=y
-CONFIG_NET=y
-CONFIG_PACKET=y
-CONFIG_UNIX=y
-CONFIG_INET=y
-CONFIG_IP_PNP=y
-CONFIG_IP_PNP_DHCP=y
-CONFIG_IP_PNP_BOOTP=y
-CONFIG_SYN_COOKIES=y
-CONFIG_IPV6=y
-# CONFIG_INET6_XFRM_MODE_TRANSPORT is not set
-# CONFIG_INET6_XFRM_MODE_TUNNEL is not set
-# CONFIG_INET6_XFRM_MODE_BEET is not set
-# CONFIG_IPV6_SIT is not set
-# CONFIG_PREVENT_FIRMWARE_BUILD is not set
-# CONFIG_FW_LOADER is not set
-CONFIG_MTD=y
-CONFIG_MTD_PARTITIONS=y
-CONFIG_MTD_REDBOOT_PARTS=y
-CONFIG_MTD_REDBOOT_PARTS_UNALLOCATED=y
-CONFIG_MTD_REDBOOT_PARTS_READONLY=y
-CONFIG_MTD_CHAR=y
-CONFIG_MTD_BLOCK=y
-CONFIG_MTD_CFI=y
-CONFIG_MTD_CFI_INTELEXT=y
-CONFIG_MTD_COMPLEX_MAPPINGS=y
-CONFIG_MTD_PHYSMAP=y
-CONFIG_BLK_DEV_LOOP=y
-CONFIG_BLK_DEV_NBD=y
-CONFIG_BLK_DEV_RAM=y
-CONFIG_BLK_DEV_RAM_SIZE=8192
-CONFIG_EEPROM_LEGACY=y
-CONFIG_IDE=y
-CONFIG_BLK_DEV_SIIMAGE=y
-CONFIG_SCSI=y
-CONFIG_BLK_DEV_SD=y
-CONFIG_NETDEVICES=y
-CONFIG_DUMMY=y
-CONFIG_NET_ETHERNET=y
-CONFIG_NET_PCI=y
-CONFIG_E100=y
-CONFIG_E1000=y
-CONFIG_WAN=y
-CONFIG_HDLC=y
-CONFIG_HDLC_RAW=y
-CONFIG_HDLC_CISCO=y
-CONFIG_HDLC_FR=y
-CONFIG_HDLC_PPP=y
-CONFIG_DLCI=y
-# CONFIG_INPUT_KEYBOARD is not set
-# CONFIG_INPUT_MOUSE is not set
-# CONFIG_SERIO is not set
-# CONFIG_VT is not set
-CONFIG_SERIAL_8250=y
-CONFIG_SERIAL_8250_CONSOLE=y
-# CONFIG_HW_RANDOM is not set
-CONFIG_I2C=y
-CONFIG_I2C_CHARDEV=y
-CONFIG_WATCHDOG=y
-# CONFIG_USB_HID is not set
-CONFIG_USB=y
-CONFIG_USB_MON=y
-CONFIG_USB_EHCI_HCD=y
-CONFIG_USB_OHCI_HCD=y
-CONFIG_USB_UHCI_HCD=y
-CONFIG_USB_STORAGE=y
-CONFIG_EXT2_FS=y
-CONFIG_EXT2_FS_XATTR=y
-CONFIG_EXT2_FS_POSIX_ACL=y
-CONFIG_EXT3_FS=y
-CONFIG_EXT3_FS_POSIX_ACL=y
-CONFIG_INOTIFY=y
-CONFIG_MSDOS_FS=y
-CONFIG_TMPFS=y
-CONFIG_JFFS2_FS=y
-CONFIG_NFS_FS=y
-CONFIG_NFS_V3=y
-CONFIG_ROOT_NFS=y
-CONFIG_PARTITION_ADVANCED=y
-CONFIG_NLS_CODEPAGE_437=y
-CONFIG_MAGIC_SYSRQ=y
-CONFIG_DEBUG_KERNEL=y
-CONFIG_DEBUG_MUTEXES=y
-CONFIG_DEBUG_USER=y
-CONFIG_DEBUG_ERRORS=y
-CONFIG_DEBUG_LL=y
+++ /dev/null
-/*
- * Generic library functions for the microengines found on the Intel
- * IXP2000 series of network processors.
- *
- * Copyright (C) 2004, 2005 Lennert Buytenhek <buytenh@wantstofly.org>
- * Dedicated to Marija Kulikova.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU Lesser General Public License as
- * published by the Free Software Foundation; either version 2.1 of the
- * License, or (at your option) any later version.
- */
-
-#ifndef __IXP2000_UENGINE_H
-#define __IXP2000_UENGINE_H
-
-extern u32 ixp2000_uengine_mask;
-
-struct ixp2000_uengine_code
-{
- u32 cpu_model_bitmask;
- u8 cpu_min_revision;
- u8 cpu_max_revision;
-
- u32 uengine_parameters;
-
- struct ixp2000_reg_value {
- int reg;
- u32 value;
- } *initial_reg_values;
-
- int num_insns;
- u8 *insns;
-};
-
-u32 ixp2000_uengine_csr_read(int uengine, int offset);
-void ixp2000_uengine_csr_write(int uengine, int offset, u32 value);
-void ixp2000_uengine_reset(u32 uengine_mask);
-void ixp2000_uengine_set_mode(int uengine, u32 mode);
-void ixp2000_uengine_load_microcode(int uengine, u8 *ucode, int insns);
-void ixp2000_uengine_init_context(int uengine, int context, int pc);
-void ixp2000_uengine_start_contexts(int uengine, u8 ctx_mask);
-void ixp2000_uengine_stop_contexts(int uengine, u8 ctx_mask);
-int ixp2000_uengine_load(int uengine, struct ixp2000_uengine_code *c);
-
-#define IXP2000_UENGINE_8_CONTEXTS 0x00000000
-#define IXP2000_UENGINE_4_CONTEXTS 0x80000000
-#define IXP2000_UENGINE_PRN_UPDATE_EVERY 0x40000000
-#define IXP2000_UENGINE_PRN_UPDATE_ON_ACCESS 0x00000000
-#define IXP2000_UENGINE_NN_FROM_SELF 0x00100000
-#define IXP2000_UENGINE_NN_FROM_PREVIOUS 0x00000000
-#define IXP2000_UENGINE_ASSERT_EMPTY_AT_3 0x000c0000
-#define IXP2000_UENGINE_ASSERT_EMPTY_AT_2 0x00080000
-#define IXP2000_UENGINE_ASSERT_EMPTY_AT_1 0x00040000
-#define IXP2000_UENGINE_ASSERT_EMPTY_AT_0 0x00000000
-#define IXP2000_UENGINE_LM_ADDR1_GLOBAL 0x00020000
-#define IXP2000_UENGINE_LM_ADDR1_PER_CONTEXT 0x00000000
-#define IXP2000_UENGINE_LM_ADDR0_GLOBAL 0x00010000
-#define IXP2000_UENGINE_LM_ADDR0_PER_CONTEXT 0x00000000
-
-
-#endif
+++ /dev/null
-
-if ARCH_IXP2000
-
-config ARCH_SUPPORTS_BIG_ENDIAN
- bool
- default y
-
-menu "Intel IXP2400/2800 Implementation Options"
-
-comment "IXP2400/2800 Platforms"
-
-config ARCH_ENP2611
- bool "Support Radisys ENP-2611"
- help
- Say 'Y' here if you want your kernel to support the Radisys
- ENP2611 PCI network processing card. For more information on
- this card, see <file:Documentation/arm/IXP2000>.
-
-config ARCH_IXDP2400
- bool "Support Intel IXDP2400"
- help
- Say 'Y' here if you want your kernel to support the Intel
- IXDP2400 reference platform. For more information on
- this platform, see <file:Documentation/arm/IXP2000>.
-
-config ARCH_IXDP2800
- bool "Support Intel IXDP2800"
- help
- Say 'Y' here if you want your kernel to support the Intel
- IXDP2800 reference platform. For more information on
- this platform, see <file:Documentation/arm/IXP2000>.
-
-config ARCH_IXDP2X00
- bool
- depends on ARCH_IXDP2400 || ARCH_IXDP2800
- default y
-
-config ARCH_IXDP2401
- bool "Support Intel IXDP2401"
- help
- Say 'Y' here if you want your kernel to support the Intel
- IXDP2401 reference platform. For more information on
- this platform, see <file:Documentation/arm/IXP2000>.
-
-config ARCH_IXDP2801
- bool "Support Intel IXDP2801 and IXDP28x5"
- help
- Say 'Y' here if you want your kernel to support the Intel
- IXDP2801/2805/2855 reference platforms. For more information on
- this platform, see <file:Documentation/arm/IXP2000>.
-
-config MACH_IXDP28X5
- bool
- depends on ARCH_IXDP2801
- default y
-
-config ARCH_IXDP2X01
- bool
- depends on ARCH_IXDP2401 || ARCH_IXDP2801
- default y
-
-config IXP2000_SUPPORT_BROKEN_PCI_IO
- bool "Support broken PCI I/O on older IXP2000s"
- default y
- help
- Say 'N' here if you only intend to run your kernel on an
- IXP2000 B0 or later model and do not need the PCI I/O
- byteswap workaround. Say 'Y' otherwise.
-
-endmenu
-
-endif
+++ /dev/null
-#
-# Makefile for the linux kernel.
-#
-obj-y := core.o pci.o
-obj-m :=
-obj-n :=
-obj- :=
-
-obj-$(CONFIG_ARCH_ENP2611) += enp2611.o
-obj-$(CONFIG_ARCH_IXDP2400) += ixdp2400.o
-obj-$(CONFIG_ARCH_IXDP2800) += ixdp2800.o
-obj-$(CONFIG_ARCH_IXDP2X00) += ixdp2x00.o
-obj-$(CONFIG_ARCH_IXDP2X01) += ixdp2x01.o
-
+++ /dev/null
- zreladdr-y += 0x00008000
-params_phys-y := 0x00000100
-
+++ /dev/null
-/*
- * arch/arm/mach-ixp2000/core.c
- *
- * Common routines used by all IXP2400/2800 based platforms.
- *
- * Author: Deepak Saxena <dsaxena@plexity.net>
- *
- * Copyright 2004 (C) MontaVista Software, Inc.
- *
- * Based on work Copyright (C) 2002-2003 Intel Corporation
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-#include <linux/gpio.h>
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/spinlock.h>
-#include <linux/sched.h>
-#include <linux/interrupt.h>
-#include <linux/irq.h>
-#include <linux/serial.h>
-#include <linux/tty.h>
-#include <linux/bitops.h>
-#include <linux/serial_8250.h>
-#include <linux/mm.h>
-#include <linux/export.h>
-
-#include <asm/types.h>
-#include <asm/setup.h>
-#include <asm/memory.h>
-#include <mach/hardware.h>
-#include <asm/irq.h>
-#include <asm/tlbflush.h>
-#include <asm/pgtable.h>
-
-#include <asm/mach/map.h>
-#include <asm/mach/time.h>
-#include <asm/mach/irq.h>
-
-#include <mach/gpio-ixp2000.h>
-
-static DEFINE_SPINLOCK(ixp2000_slowport_lock);
-static unsigned long ixp2000_slowport_irq_flags;
-
-/*************************************************************************
- * Slowport access routines
- *************************************************************************/
-void ixp2000_acquire_slowport(struct slowport_cfg *new_cfg, struct slowport_cfg *old_cfg)
-{
- spin_lock_irqsave(&ixp2000_slowport_lock, ixp2000_slowport_irq_flags);
-
- old_cfg->CCR = *IXP2000_SLOWPORT_CCR;
- old_cfg->WTC = *IXP2000_SLOWPORT_WTC2;
- old_cfg->RTC = *IXP2000_SLOWPORT_RTC2;
- old_cfg->PCR = *IXP2000_SLOWPORT_PCR;
- old_cfg->ADC = *IXP2000_SLOWPORT_ADC;
-
- ixp2000_reg_write(IXP2000_SLOWPORT_CCR, new_cfg->CCR);
- ixp2000_reg_write(IXP2000_SLOWPORT_WTC2, new_cfg->WTC);
- ixp2000_reg_write(IXP2000_SLOWPORT_RTC2, new_cfg->RTC);
- ixp2000_reg_write(IXP2000_SLOWPORT_PCR, new_cfg->PCR);
- ixp2000_reg_wrb(IXP2000_SLOWPORT_ADC, new_cfg->ADC);
-}
-
-void ixp2000_release_slowport(struct slowport_cfg *old_cfg)
-{
- ixp2000_reg_write(IXP2000_SLOWPORT_CCR, old_cfg->CCR);
- ixp2000_reg_write(IXP2000_SLOWPORT_WTC2, old_cfg->WTC);
- ixp2000_reg_write(IXP2000_SLOWPORT_RTC2, old_cfg->RTC);
- ixp2000_reg_write(IXP2000_SLOWPORT_PCR, old_cfg->PCR);
- ixp2000_reg_wrb(IXP2000_SLOWPORT_ADC, old_cfg->ADC);
-
- spin_unlock_irqrestore(&ixp2000_slowport_lock,
- ixp2000_slowport_irq_flags);
-}
-
-/*************************************************************************
- * Chip specific mappings shared by all IXP2000 systems
- *************************************************************************/
-static struct map_desc ixp2000_io_desc[] __initdata = {
- {
- .virtual = IXP2000_CAP_VIRT_BASE,
- .pfn = __phys_to_pfn(IXP2000_CAP_PHYS_BASE),
- .length = IXP2000_CAP_SIZE,
- .type = MT_DEVICE,
- }, {
- .virtual = IXP2000_INTCTL_VIRT_BASE,
- .pfn = __phys_to_pfn(IXP2000_INTCTL_PHYS_BASE),
- .length = IXP2000_INTCTL_SIZE,
- .type = MT_DEVICE,
- }, {
- .virtual = IXP2000_PCI_CREG_VIRT_BASE,
- .pfn = __phys_to_pfn(IXP2000_PCI_CREG_PHYS_BASE),
- .length = IXP2000_PCI_CREG_SIZE,
- .type = MT_DEVICE,
- }, {
- .virtual = IXP2000_PCI_CSR_VIRT_BASE,
- .pfn = __phys_to_pfn(IXP2000_PCI_CSR_PHYS_BASE),
- .length = IXP2000_PCI_CSR_SIZE,
- .type = MT_DEVICE,
- }, {
- .virtual = IXP2000_MSF_VIRT_BASE,
- .pfn = __phys_to_pfn(IXP2000_MSF_PHYS_BASE),
- .length = IXP2000_MSF_SIZE,
- .type = MT_DEVICE,
- }, {
- .virtual = IXP2000_SCRATCH_RING_VIRT_BASE,
- .pfn = __phys_to_pfn(IXP2000_SCRATCH_RING_PHYS_BASE),
- .length = IXP2000_SCRATCH_RING_SIZE,
- .type = MT_DEVICE,
- }, {
- .virtual = IXP2000_SRAM0_VIRT_BASE,
- .pfn = __phys_to_pfn(IXP2000_SRAM0_PHYS_BASE),
- .length = IXP2000_SRAM0_SIZE,
- .type = MT_DEVICE,
- }, {
- .virtual = IXP2000_PCI_IO_VIRT_BASE,
- .pfn = __phys_to_pfn(IXP2000_PCI_IO_PHYS_BASE),
- .length = IXP2000_PCI_IO_SIZE,
- .type = MT_DEVICE,
- }, {
- .virtual = IXP2000_PCI_CFG0_VIRT_BASE,
- .pfn = __phys_to_pfn(IXP2000_PCI_CFG0_PHYS_BASE),
- .length = IXP2000_PCI_CFG0_SIZE,
- .type = MT_DEVICE,
- }, {
- .virtual = IXP2000_PCI_CFG1_VIRT_BASE,
- .pfn = __phys_to_pfn(IXP2000_PCI_CFG1_PHYS_BASE),
- .length = IXP2000_PCI_CFG1_SIZE,
- .type = MT_DEVICE,
- }
-};
-
-void __init ixp2000_map_io(void)
-{
- iotable_init(ixp2000_io_desc, ARRAY_SIZE(ixp2000_io_desc));
-
- /* Set slowport to 8-bit mode. */
- ixp2000_reg_wrb(IXP2000_SLOWPORT_FRM, 1);
-}
-
-
-/*************************************************************************
- * Serial port support for IXP2000
- *************************************************************************/
-static struct plat_serial8250_port ixp2000_serial_port[] = {
- {
- .mapbase = IXP2000_UART_PHYS_BASE,
- .membase = (char *)(IXP2000_UART_VIRT_BASE + 3),
- .irq = IRQ_IXP2000_UART,
- .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
- .iotype = UPIO_MEM,
- .regshift = 2,
- .uartclk = 50000000,
- },
- { },
-};
-
-static struct resource ixp2000_uart_resource = {
- .start = IXP2000_UART_PHYS_BASE,
- .end = IXP2000_UART_PHYS_BASE + 0x1f,
- .flags = IORESOURCE_MEM,
-};
-
-static struct platform_device ixp2000_serial_device = {
- .name = "serial8250",
- .id = PLAT8250_DEV_PLATFORM,
- .dev = {
- .platform_data = ixp2000_serial_port,
- },
- .num_resources = 1,
- .resource = &ixp2000_uart_resource,
-};
-
-void __init ixp2000_uart_init(void)
-{
- platform_device_register(&ixp2000_serial_device);
-}
-
-
-/*************************************************************************
- * Timer-tick functions for IXP2000
- *************************************************************************/
-static unsigned ticks_per_jiffy;
-static unsigned ticks_per_usec;
-static unsigned next_jiffy_time;
-static volatile unsigned long *missing_jiffy_timer_csr;
-
-unsigned long ixp2000_gettimeoffset (void)
-{
- unsigned long offset;
-
- offset = next_jiffy_time - *missing_jiffy_timer_csr;
-
- return offset / ticks_per_usec;
-}
-
-static irqreturn_t ixp2000_timer_interrupt(int irq, void *dev_id)
-{
- /* clear timer 1 */
- ixp2000_reg_wrb(IXP2000_T1_CLR, 1);
-
- while ((signed long)(next_jiffy_time - *missing_jiffy_timer_csr)
- >= ticks_per_jiffy) {
- timer_tick();
- next_jiffy_time -= ticks_per_jiffy;
- }
-
- return IRQ_HANDLED;
-}
-
-static struct irqaction ixp2000_timer_irq = {
- .name = "IXP2000 Timer Tick",
- .flags = IRQF_DISABLED | IRQF_TIMER | IRQF_IRQPOLL,
- .handler = ixp2000_timer_interrupt,
-};
-
-void __init ixp2000_init_time(unsigned long tick_rate)
-{
- ticks_per_jiffy = (tick_rate + HZ/2) / HZ;
- ticks_per_usec = tick_rate / 1000000;
-
- /*
- * We use timer 1 as our timer interrupt.
- */
- ixp2000_reg_write(IXP2000_T1_CLR, 0);
- ixp2000_reg_write(IXP2000_T1_CLD, ticks_per_jiffy - 1);
- ixp2000_reg_write(IXP2000_T1_CTL, (1 << 7));
-
- /*
- * We use a second timer as a monotonic counter for tracking
- * missed jiffies. The IXP2000 has four timers, but if we're
- * on an A-step IXP2800, timer 2 and 3 don't work, so on those
- * chips we use timer 4. Timer 4 is the only timer that can
- * be used for the watchdog, so we use timer 2 if we're on a
- * non-buggy chip.
- */
- if ((*IXP2000_PRODUCT_ID & 0x001ffef0) == 0x00000000) {
- printk(KERN_INFO "Enabling IXP2800 erratum #25 workaround\n");
-
- ixp2000_reg_write(IXP2000_T4_CLR, 0);
- ixp2000_reg_write(IXP2000_T4_CLD, -1);
- ixp2000_reg_wrb(IXP2000_T4_CTL, (1 << 7));
- missing_jiffy_timer_csr = IXP2000_T4_CSR;
- } else {
- ixp2000_reg_write(IXP2000_T2_CLR, 0);
- ixp2000_reg_write(IXP2000_T2_CLD, -1);
- ixp2000_reg_wrb(IXP2000_T2_CTL, (1 << 7));
- missing_jiffy_timer_csr = IXP2000_T2_CSR;
- }
- next_jiffy_time = 0xffffffff;
-
- /* register for interrupt */
- setup_irq(IRQ_IXP2000_TIMER1, &ixp2000_timer_irq);
-}
-
-/*************************************************************************
- * GPIO helpers
- *************************************************************************/
-static unsigned long GPIO_IRQ_falling_edge;
-static unsigned long GPIO_IRQ_rising_edge;
-static unsigned long GPIO_IRQ_level_low;
-static unsigned long GPIO_IRQ_level_high;
-
-static void update_gpio_int_csrs(void)
-{
- ixp2000_reg_write(IXP2000_GPIO_FEDR, GPIO_IRQ_falling_edge);
- ixp2000_reg_write(IXP2000_GPIO_REDR, GPIO_IRQ_rising_edge);
- ixp2000_reg_write(IXP2000_GPIO_LSLR, GPIO_IRQ_level_low);
- ixp2000_reg_wrb(IXP2000_GPIO_LSHR, GPIO_IRQ_level_high);
-}
-
-void gpio_line_config(int line, int direction)
-{
- unsigned long flags;
-
- local_irq_save(flags);
- if (direction == GPIO_OUT) {
- /* if it's an output, it ain't an interrupt anymore */
- GPIO_IRQ_falling_edge &= ~(1 << line);
- GPIO_IRQ_rising_edge &= ~(1 << line);
- GPIO_IRQ_level_low &= ~(1 << line);
- GPIO_IRQ_level_high &= ~(1 << line);
- update_gpio_int_csrs();
-
- ixp2000_reg_wrb(IXP2000_GPIO_PDSR, 1 << line);
- } else if (direction == GPIO_IN) {
- ixp2000_reg_wrb(IXP2000_GPIO_PDCR, 1 << line);
- }
- local_irq_restore(flags);
-}
-EXPORT_SYMBOL(gpio_line_config);
-
-
-/*************************************************************************
- * IRQ handling IXP2000
- *************************************************************************/
-static void ixp2000_GPIO_irq_handler(unsigned int irq, struct irq_desc *desc)
-{
- int i;
- unsigned long status = *IXP2000_GPIO_INST;
-
- for (i = 0; i <= 7; i++) {
- if (status & (1<<i)) {
- generic_handle_irq(i + IRQ_IXP2000_GPIO0);
- }
- }
-}
-
-static int ixp2000_GPIO_irq_type(struct irq_data *d, unsigned int type)
-{
- int line = d->irq - IRQ_IXP2000_GPIO0;
-
- /*
- * First, configure this GPIO line as an input.
- */
- ixp2000_reg_write(IXP2000_GPIO_PDCR, 1 << line);
-
- /*
- * Then, set the proper trigger type.
- */
- if (type & IRQ_TYPE_EDGE_FALLING)
- GPIO_IRQ_falling_edge |= 1 << line;
- else
- GPIO_IRQ_falling_edge &= ~(1 << line);
- if (type & IRQ_TYPE_EDGE_RISING)
- GPIO_IRQ_rising_edge |= 1 << line;
- else
- GPIO_IRQ_rising_edge &= ~(1 << line);
- if (type & IRQ_TYPE_LEVEL_LOW)
- GPIO_IRQ_level_low |= 1 << line;
- else
- GPIO_IRQ_level_low &= ~(1 << line);
- if (type & IRQ_TYPE_LEVEL_HIGH)
- GPIO_IRQ_level_high |= 1 << line;
- else
- GPIO_IRQ_level_high &= ~(1 << line);
- update_gpio_int_csrs();
-
- return 0;
-}
-
-static void ixp2000_GPIO_irq_mask_ack(struct irq_data *d)
-{
- unsigned int irq = d->irq;
-
- ixp2000_reg_write(IXP2000_GPIO_INCR, (1 << (irq - IRQ_IXP2000_GPIO0)));
-
- ixp2000_reg_write(IXP2000_GPIO_EDSR, (1 << (irq - IRQ_IXP2000_GPIO0)));
- ixp2000_reg_write(IXP2000_GPIO_LDSR, (1 << (irq - IRQ_IXP2000_GPIO0)));
- ixp2000_reg_wrb(IXP2000_GPIO_INST, (1 << (irq - IRQ_IXP2000_GPIO0)));
-}
-
-static void ixp2000_GPIO_irq_mask(struct irq_data *d)
-{
- unsigned int irq = d->irq;
-
- ixp2000_reg_wrb(IXP2000_GPIO_INCR, (1 << (irq - IRQ_IXP2000_GPIO0)));
-}
-
-static void ixp2000_GPIO_irq_unmask(struct irq_data *d)
-{
- unsigned int irq = d->irq;
-
- ixp2000_reg_write(IXP2000_GPIO_INSR, (1 << (irq - IRQ_IXP2000_GPIO0)));
-}
-
-static struct irq_chip ixp2000_GPIO_irq_chip = {
- .irq_ack = ixp2000_GPIO_irq_mask_ack,
- .irq_mask = ixp2000_GPIO_irq_mask,
- .irq_unmask = ixp2000_GPIO_irq_unmask,
- .irq_set_type = ixp2000_GPIO_irq_type,
-};
-
-static void ixp2000_pci_irq_mask(struct irq_data *d)
-{
- unsigned long temp = *IXP2000_PCI_XSCALE_INT_ENABLE;
- if (d->irq == IRQ_IXP2000_PCIA)
- ixp2000_reg_wrb(IXP2000_PCI_XSCALE_INT_ENABLE, (temp & ~(1 << 26)));
- else if (d->irq == IRQ_IXP2000_PCIB)
- ixp2000_reg_wrb(IXP2000_PCI_XSCALE_INT_ENABLE, (temp & ~(1 << 27)));
-}
-
-static void ixp2000_pci_irq_unmask(struct irq_data *d)
-{
- unsigned long temp = *IXP2000_PCI_XSCALE_INT_ENABLE;
- if (d->irq == IRQ_IXP2000_PCIA)
- ixp2000_reg_write(IXP2000_PCI_XSCALE_INT_ENABLE, (temp | (1 << 26)));
- else if (d->irq == IRQ_IXP2000_PCIB)
- ixp2000_reg_write(IXP2000_PCI_XSCALE_INT_ENABLE, (temp | (1 << 27)));
-}
-
-/*
- * Error interrupts. These are used extensively by the microengine drivers
- */
-static void ixp2000_err_irq_handler(unsigned int irq, struct irq_desc *desc)
-{
- int i;
- unsigned long status = *IXP2000_IRQ_ERR_STATUS;
-
- for(i = 31; i >= 0; i--) {
- if(status & (1 << i)) {
- generic_handle_irq(IRQ_IXP2000_DRAM0_MIN_ERR + i);
- }
- }
-}
-
-static void ixp2000_err_irq_mask(struct irq_data *d)
-{
- ixp2000_reg_write(IXP2000_IRQ_ERR_ENABLE_CLR,
- (1 << (d->irq - IRQ_IXP2000_DRAM0_MIN_ERR)));
-}
-
-static void ixp2000_err_irq_unmask(struct irq_data *d)
-{
- ixp2000_reg_write(IXP2000_IRQ_ERR_ENABLE_SET,
- (1 << (d->irq - IRQ_IXP2000_DRAM0_MIN_ERR)));
-}
-
-static struct irq_chip ixp2000_err_irq_chip = {
- .irq_ack = ixp2000_err_irq_mask,
- .irq_mask = ixp2000_err_irq_mask,
- .irq_unmask = ixp2000_err_irq_unmask
-};
-
-static struct irq_chip ixp2000_pci_irq_chip = {
- .irq_ack = ixp2000_pci_irq_mask,
- .irq_mask = ixp2000_pci_irq_mask,
- .irq_unmask = ixp2000_pci_irq_unmask
-};
-
-static void ixp2000_irq_mask(struct irq_data *d)
-{
- ixp2000_reg_wrb(IXP2000_IRQ_ENABLE_CLR, (1 << d->irq));
-}
-
-static void ixp2000_irq_unmask(struct irq_data *d)
-{
- ixp2000_reg_write(IXP2000_IRQ_ENABLE_SET, (1 << d->irq));
-}
-
-static struct irq_chip ixp2000_irq_chip = {
- .irq_ack = ixp2000_irq_mask,
- .irq_mask = ixp2000_irq_mask,
- .irq_unmask = ixp2000_irq_unmask
-};
-
-void __init ixp2000_init_irq(void)
-{
- int irq;
-
- /*
- * Mask all sources
- */
- ixp2000_reg_write(IXP2000_IRQ_ENABLE_CLR, 0xffffffff);
- ixp2000_reg_write(IXP2000_FIQ_ENABLE_CLR, 0xffffffff);
-
- /* clear all GPIO edge/level detects */
- ixp2000_reg_write(IXP2000_GPIO_REDR, 0);
- ixp2000_reg_write(IXP2000_GPIO_FEDR, 0);
- ixp2000_reg_write(IXP2000_GPIO_LSHR, 0);
- ixp2000_reg_write(IXP2000_GPIO_LSLR, 0);
- ixp2000_reg_write(IXP2000_GPIO_INCR, -1);
-
- /* clear PCI interrupt sources */
- ixp2000_reg_wrb(IXP2000_PCI_XSCALE_INT_ENABLE, 0);
-
- /*
- * Certain bits in the IRQ status register of the
- * IXP2000 are reserved. Instead of trying to map
- * things non 1:1 from bit position to IRQ number,
- * we mark the reserved IRQs as invalid. This makes
- * our mask/unmask code much simpler.
- */
- for (irq = IRQ_IXP2000_SOFT_INT; irq <= IRQ_IXP2000_THDB3; irq++) {
- if ((1 << irq) & IXP2000_VALID_IRQ_MASK) {
- irq_set_chip_and_handler(irq, &ixp2000_irq_chip,
- handle_level_irq);
- set_irq_flags(irq, IRQF_VALID);
- } else set_irq_flags(irq, 0);
- }
-
- for (irq = IRQ_IXP2000_DRAM0_MIN_ERR; irq <= IRQ_IXP2000_SP_INT; irq++) {
- if((1 << (irq - IRQ_IXP2000_DRAM0_MIN_ERR)) &
- IXP2000_VALID_ERR_IRQ_MASK) {
- irq_set_chip_and_handler(irq, &ixp2000_err_irq_chip,
- handle_level_irq);
- set_irq_flags(irq, IRQF_VALID);
- }
- else
- set_irq_flags(irq, 0);
- }
- irq_set_chained_handler(IRQ_IXP2000_ERRSUM, ixp2000_err_irq_handler);
-
- for (irq = IRQ_IXP2000_GPIO0; irq <= IRQ_IXP2000_GPIO7; irq++) {
- irq_set_chip_and_handler(irq, &ixp2000_GPIO_irq_chip,
- handle_level_irq);
- set_irq_flags(irq, IRQF_VALID);
- }
- irq_set_chained_handler(IRQ_IXP2000_GPIO, ixp2000_GPIO_irq_handler);
-
- /*
- * Enable PCI irqs. The actual PCI[AB] decoding is done in
- * entry-macro.S, so we don't need a chained handler for the
- * PCI interrupt source.
- */
- ixp2000_reg_write(IXP2000_IRQ_ENABLE_SET, (1 << IRQ_IXP2000_PCI));
- for (irq = IRQ_IXP2000_PCIA; irq <= IRQ_IXP2000_PCIB; irq++) {
- irq_set_chip_and_handler(irq, &ixp2000_pci_irq_chip,
- handle_level_irq);
- set_irq_flags(irq, IRQF_VALID);
- }
-}
-
-void ixp2000_restart(char mode, const char *cmd)
-{
- ixp2000_reg_wrb(IXP2000_RESET0, RSTALL);
-}
+++ /dev/null
-/*
- * arch/arm/mach-ixp2000/enp2611.c
- *
- * Radisys ENP-2611 support.
- *
- * Created 2004 by Lennert Buytenhek from the ixdp2x01 code. The
- * original version carries the following notices:
- *
- * Original Author: Andrzej Mialkowski <andrzej.mialkowski@intel.com>
- * Maintainer: Deepak Saxena <dsaxena@plexity.net>
- *
- * Copyright (C) 2002-2003 Intel Corp.
- * Copyright (C) 2003-2004 MontaVista Software, Inc.
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/mm.h>
-#include <linux/sched.h>
-#include <linux/interrupt.h>
-#include <linux/bitops.h>
-#include <linux/pci.h>
-#include <linux/ioport.h>
-#include <linux/delay.h>
-#include <linux/serial.h>
-#include <linux/tty.h>
-#include <linux/serial_core.h>
-#include <linux/platform_device.h>
-#include <linux/io.h>
-
-#include <asm/irq.h>
-#include <asm/pgtable.h>
-#include <asm/page.h>
-#include <mach/hardware.h>
-#include <asm/mach-types.h>
-
-#include <asm/mach/pci.h>
-#include <asm/mach/map.h>
-#include <asm/mach/irq.h>
-#include <asm/mach/time.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/flash.h>
-
-/*************************************************************************
- * ENP-2611 timer tick configuration
- *************************************************************************/
-static void __init enp2611_timer_init(void)
-{
- ixp2000_init_time(50 * 1000 * 1000);
-}
-
-static struct sys_timer enp2611_timer = {
- .init = enp2611_timer_init,
- .offset = ixp2000_gettimeoffset,
-};
-
-
-/*************************************************************************
- * ENP-2611 I/O
- *************************************************************************/
-static struct map_desc enp2611_io_desc[] __initdata = {
- {
- .virtual = ENP2611_CALEB_VIRT_BASE,
- .pfn = __phys_to_pfn(ENP2611_CALEB_PHYS_BASE),
- .length = ENP2611_CALEB_SIZE,
- .type = MT_DEVICE,
- }, {
- .virtual = ENP2611_PM3386_0_VIRT_BASE,
- .pfn = __phys_to_pfn(ENP2611_PM3386_0_PHYS_BASE),
- .length = ENP2611_PM3386_0_SIZE,
- .type = MT_DEVICE,
- }, {
- .virtual = ENP2611_PM3386_1_VIRT_BASE,
- .pfn = __phys_to_pfn(ENP2611_PM3386_1_PHYS_BASE),
- .length = ENP2611_PM3386_1_SIZE,
- .type = MT_DEVICE,
- }
-};
-
-void __init enp2611_map_io(void)
-{
- ixp2000_map_io();
- iotable_init(enp2611_io_desc, ARRAY_SIZE(enp2611_io_desc));
-}
-
-
-/*************************************************************************
- * ENP-2611 PCI
- *************************************************************************/
-static int enp2611_pci_setup(int nr, struct pci_sys_data *sys)
-{
- sys->mem_offset = 0xe0000000;
- ixp2000_pci_setup(nr, sys);
- return 1;
-}
-
-static void __init enp2611_pci_preinit(void)
-{
- ixp2000_reg_write(IXP2000_PCI_ADDR_EXT, 0x00100000);
- ixp2000_pci_preinit();
- pcibios_setup("firmware");
-}
-
-static inline int enp2611_pci_valid_device(struct pci_bus *bus,
- unsigned int devfn)
-{
- /* The 82559 ethernet controller appears at both PCI:1:0:0 and
- * PCI:1:2:0, so let's pretend the second one isn't there.
- */
- if (bus->number == 0x01 && devfn == 0x10)
- return 0;
-
- return 1;
-}
-
-static int enp2611_pci_read_config(struct pci_bus *bus, unsigned int devfn,
- int where, int size, u32 *value)
-{
- if (enp2611_pci_valid_device(bus, devfn))
- return ixp2000_pci_read_config(bus, devfn, where, size, value);
-
- return PCIBIOS_DEVICE_NOT_FOUND;
-}
-
-static int enp2611_pci_write_config(struct pci_bus *bus, unsigned int devfn,
- int where, int size, u32 value)
-{
- if (enp2611_pci_valid_device(bus, devfn))
- return ixp2000_pci_write_config(bus, devfn, where, size, value);
-
- return PCIBIOS_DEVICE_NOT_FOUND;
-}
-
-static struct pci_ops enp2611_pci_ops = {
- .read = enp2611_pci_read_config,
- .write = enp2611_pci_write_config
-};
-
-static struct pci_bus * __init enp2611_pci_scan_bus(int nr,
- struct pci_sys_data *sys)
-{
- return pci_scan_root_bus(NULL, sys->busnr, &enp2611_pci_ops, sys,
- &sys->resources);
-}
-
-static int __init enp2611_pci_map_irq(const struct pci_dev *dev, u8 slot,
- u8 pin)
-{
- int irq;
-
- if (dev->bus->number == 0 && PCI_SLOT(dev->devfn) == 0) {
- /* IXP2400. */
- irq = IRQ_IXP2000_PCIA;
- } else if (dev->bus->number == 0 && PCI_SLOT(dev->devfn) == 1) {
- /* 21555 non-transparent bridge. */
- irq = IRQ_IXP2000_PCIB;
- } else if (dev->bus->number == 0 && PCI_SLOT(dev->devfn) == 4) {
- /* PCI2050B transparent bridge. */
- irq = -1;
- } else if (dev->bus->number == 1 && PCI_SLOT(dev->devfn) == 0) {
- /* 82559 ethernet. */
- irq = IRQ_IXP2000_PCIA;
- } else if (dev->bus->number == 1 && PCI_SLOT(dev->devfn) == 1) {
- /* SPI-3 option board. */
- irq = IRQ_IXP2000_PCIB;
- } else {
- printk(KERN_ERR "enp2611_pci_map_irq() called for unknown "
- "device PCI:%d:%d:%d\n", dev->bus->number,
- PCI_SLOT(dev->devfn), PCI_FUNC(dev->devfn));
- irq = -1;
- }
-
- return irq;
-}
-
-struct hw_pci enp2611_pci __initdata = {
- .nr_controllers = 1,
- .setup = enp2611_pci_setup,
- .preinit = enp2611_pci_preinit,
- .scan = enp2611_pci_scan_bus,
- .map_irq = enp2611_pci_map_irq,
-};
-
-int __init enp2611_pci_init(void)
-{
- if (machine_is_enp2611())
- pci_common_init(&enp2611_pci);
-
- return 0;
-}
-
-subsys_initcall(enp2611_pci_init);
-
-
-/*************************************************************************
- * ENP-2611 Machine Initialization
- *************************************************************************/
-static struct flash_platform_data enp2611_flash_platform_data = {
- .map_name = "cfi_probe",
- .width = 1,
-};
-
-static struct ixp2000_flash_data enp2611_flash_data = {
- .platform_data = &enp2611_flash_platform_data,
- .nr_banks = 1
-};
-
-static struct resource enp2611_flash_resource = {
- .start = 0xc4000000,
- .end = 0xc4000000 + 0x00ffffff,
- .flags = IORESOURCE_MEM,
-};
-
-static struct platform_device enp2611_flash = {
- .name = "IXP2000-Flash",
- .id = 0,
- .dev = {
- .platform_data = &enp2611_flash_data,
- },
- .num_resources = 1,
- .resource = &enp2611_flash_resource,
-};
-
-static struct ixp2000_i2c_pins enp2611_i2c_gpio_pins = {
- .sda_pin = ENP2611_GPIO_SDA,
- .scl_pin = ENP2611_GPIO_SCL,
-};
-
-static struct platform_device enp2611_i2c_controller = {
- .name = "IXP2000-I2C",
- .id = 0,
- .dev = {
- .platform_data = &enp2611_i2c_gpio_pins
- },
- .num_resources = 0
-};
-
-static struct platform_device *enp2611_devices[] __initdata = {
- &enp2611_flash,
- &enp2611_i2c_controller
-};
-
-static void __init enp2611_init_machine(void)
-{
- platform_add_devices(enp2611_devices, ARRAY_SIZE(enp2611_devices));
- ixp2000_uart_init();
-}
-
-
-MACHINE_START(ENP2611, "Radisys ENP-2611 PCI network processor board")
- /* Maintainer: Lennert Buytenhek <buytenh@wantstofly.org> */
- .atag_offset = 0x100,
- .map_io = enp2611_map_io,
- .init_irq = ixp2000_init_irq,
- .timer = &enp2611_timer,
- .init_machine = enp2611_init_machine,
- .restart = ixp2000_restart,
-MACHINE_END
-
-
+++ /dev/null
-/* arch/arm/mach-ixp2000/include/mach/debug-macro.S
- *
- * Debugging macro include header
- *
- * Copyright (C) 1994-1999 Russell King
- * Moved from linux/arch/arm/kernel/debug.S by Ben Dooks
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
-*/
-
- .macro addruart, rp, rv, tmp
- mov \rp, #0x00030000
-#ifdef __ARMEB__
- orr \rp, \rp, #0x00000003
-#endif
- orr \rv, \rp, #0xfe000000 @ virtual base
- orr \rv, \rv, #0x00f00000
- orr \rp, \rp, #0xc0000000 @ Physical base
- .endm
-
-#define UART_SHIFT 2
-#include <asm/hardware/debug-8250.S>
+++ /dev/null
-/*
- * arch/arm/mach-ixp2000/include/mach/enp2611.h
- *
- * Register and other defines for Radisys ENP-2611
- *
- * Created 2004 by Lennert Buytenhek from the ixdp2x01 code. The
- * original version carries the following notices:
- *
- * Original Author: Naeem Afzal <naeem.m.afzal@intel.com>
- * Maintainer: Deepak Saxena <dsaxena@plexity.net>
- *
- * Copyright (C) 2002 Intel Corp.
- * Copyright (C) 2003-2004 MontaVista Software, Inc.
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- */
-
-#ifndef __ENP2611_H
-#define __ENP2611_H
-
-#define ENP2611_CALEB_PHYS_BASE 0xc5000000
-#define ENP2611_CALEB_VIRT_BASE 0xfe000000
-#define ENP2611_CALEB_SIZE 0x00100000
-
-#define ENP2611_PM3386_0_PHYS_BASE 0xc6000000
-#define ENP2611_PM3386_0_VIRT_BASE 0xfe100000
-#define ENP2611_PM3386_0_SIZE 0x00100000
-
-#define ENP2611_PM3386_1_PHYS_BASE 0xc6400000
-#define ENP2611_PM3386_1_VIRT_BASE 0xfe200000
-#define ENP2611_PM3386_1_SIZE 0x00100000
-
-#define ENP2611_GPIO_SCL 7
-#define ENP2611_GPIO_SDA 6
-
-#define IRQ_ENP2611_THERMAL IRQ_IXP2000_GPIO4
-#define IRQ_ENP2611_OPTION_BOARD IRQ_IXP2000_GPIO3
-#define IRQ_ENP2611_CALEB IRQ_IXP2000_GPIO2
-#define IRQ_ENP2611_PM3386_1 IRQ_IXP2000_GPIO1
-#define IRQ_ENP2611_PM3386_0 IRQ_IXP2000_GPIO0
-
-
-#endif
+++ /dev/null
-/*
- * arch/arm/mach-ixp2000/include/mach/entry-macro.S
- *
- * Low-level IRQ helper macros for IXP2000-based platforms
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-#include <mach/irqs.h>
-
- .macro get_irqnr_preamble, base, tmp
- .endm
-
- .macro get_irqnr_and_base, irqnr, irqstat, base, tmp
-
- mov \irqnr, #0x0 @clear out irqnr as default
- mov \base, #0xfe000000
- orr \base, \base, #0x00e00000
- orr \base, \base, #0x08
- ldr \irqstat, [\base] @ get interrupts
-
- cmp \irqstat, #0
- beq 1001f
-
- clz \irqnr, \irqstat
- mov \base, #31
- subs \irqnr, \base, \irqnr
-
- /*
- * We handle PCIA and PCIB here so we don't have an
- * extra layer of code just to check these two bits.
- */
- cmp \irqnr, #IRQ_IXP2000_PCI
- bne 1001f
-
- mov \base, #0xfe000000
- orr \base, \base, #0x00c00000
- orr \base, \base, #0x00000100
- orr \base, \base, #0x00000058
- ldr \irqstat, [\base]
-
- mov \tmp, #(1<<26)
- tst \irqstat, \tmp
- movne \irqnr, #IRQ_IXP2000_PCIA
- bne 1001f
-
- mov \tmp, #(1<<27)
- tst \irqstat, \tmp
- movne \irqnr, #IRQ_IXP2000_PCIB
-
-1001:
- .endm
-
+++ /dev/null
-/*
- * arch/arm/mach-ixp2000/include/mach/gpio.h
- *
- * Copyright (C) 2002 Intel Corporation.
- *
- * This program is free software, you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-/*
- * IXP2000 GPIO in/out, edge/level detection for IRQs:
- * IRQs are generated on Falling-edge, Rising-Edge, Level-low, Level-High
- * or both Falling-edge and Rising-edge.
- * This must be called *before* the corresponding IRQ is registerd.
- * Use this instead of directly setting the GPIO registers.
- * GPIOs may also be used as GPIOs (e.g. for emulating i2c/smb)
- */
-#ifndef __ASM_ARCH_GPIO_H
-#define __ASM_ARCH_GPIO_H
-
-#ifndef __ASSEMBLY__
-
-#define GPIO_IN 0
-#define GPIO_OUT 1
-
-#define IXP2000_GPIO_LOW 0
-#define IXP2000_GPIO_HIGH 1
-
-extern void gpio_line_config(int line, int direction);
-
-static inline int gpio_line_get(int line)
-{
- return (((*IXP2000_GPIO_PLR) >> line) & 1);
-}
-
-static inline void gpio_line_set(int line, int value)
-{
- if (value == IXP2000_GPIO_HIGH) {
- ixp2000_reg_write(IXP2000_GPIO_POSR, 1 << line);
- } else if (value == IXP2000_GPIO_LOW) {
- ixp2000_reg_write(IXP2000_GPIO_POCR, 1 << line);
- }
-}
-
-#endif /* !__ASSEMBLY__ */
-
-#endif /* ASM_ARCH_IXP2000_GPIO_H_ */
+++ /dev/null
-/*
- * arch/arm/mach-ixp2000/include/mach/hardware.h
- *
- * Hardware definitions for IXP2400/2800 based systems
- *
- * Original Author: Naeem M Afzal <naeem.m.afzal@intel.com>
- *
- * Maintainer: Deepak Saxena <dsaxena@mvista.com>
- *
- * Copyright (C) 2001-2002 Intel Corp.
- * Copyright (C) 2003-2004 MontaVista Software, Inc.
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- */
-
-#ifndef __ASM_ARCH_HARDWARE_H__
-#define __ASM_ARCH_HARDWARE_H__
-
-#include "ixp2000-regs.h" /* Chipset Registers */
-
-/*
- * Platform helper functions
- */
-#include "platform.h"
-
-/*
- * Platform-specific bits
- */
-#include "enp2611.h" /* ENP-2611 */
-#include "ixdp2x00.h" /* IXDP2400/2800 */
-#include "ixdp2x01.h" /* IXDP2401/2801 */
-
-#endif /* _ASM_ARCH_HARDWARE_H__ */
+++ /dev/null
-/*
- * arch/arm/mach-ixp2000/include/mach/io.h
- *
- * Original Author: Naeem M Afzal <naeem.m.afzal@intel.com>
- * Maintainer: Deepak Saxena <dsaxena@plexity.net>
- *
- * Copyright (C) 2002 Intel Corp.
- * Copyrgiht (C) 2003-2004 MontaVista Software, Inc.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#ifndef __ASM_ARM_ARCH_IO_H
-#define __ASM_ARM_ARCH_IO_H
-
-#include <mach/hardware.h>
-
-#define IO_SPACE_LIMIT 0xffffffff
-
-/*
- * The A? revisions of the IXP2000s assert byte lanes for PCI I/O
- * transactions the other way round (MEM transactions don't have this
- * issue), so if we want to support those models, we need to override
- * the standard I/O functions.
- *
- * B0 and later have a bit that can be set to 1 to get the proper
- * behavior for I/O transactions, which then allows us to use the
- * standard I/O functions. This is what we do if the user does not
- * explicitly ask for support for pre-B0.
- */
-#ifdef CONFIG_IXP2000_SUPPORT_BROKEN_PCI_IO
-#define ___io(p) ((void __iomem *)((p)+IXP2000_PCI_IO_VIRT_BASE))
-
-#define alignb(addr) (void __iomem *)((unsigned long)(addr) ^ 3)
-#define alignw(addr) (void __iomem *)((unsigned long)(addr) ^ 2)
-
-#define outb(v,p) __raw_writeb((v),alignb(___io(p)))
-#define outw(v,p) __raw_writew((v),alignw(___io(p)))
-#define outl(v,p) __raw_writel((v),___io(p))
-
-#define inb(p) ({ unsigned int __v = __raw_readb(alignb(___io(p))); __v; })
-#define inw(p) \
- ({ unsigned int __v = (__raw_readw(alignw(___io(p)))); __v; })
-#define inl(p) \
- ({ unsigned int __v = (__raw_readl(___io(p))); __v; })
-
-#define outsb(p,d,l) __raw_writesb(alignb(___io(p)),d,l)
-#define outsw(p,d,l) __raw_writesw(alignw(___io(p)),d,l)
-#define outsl(p,d,l) __raw_writesl(___io(p),d,l)
-
-#define insb(p,d,l) __raw_readsb(alignb(___io(p)),d,l)
-#define insw(p,d,l) __raw_readsw(alignw(___io(p)),d,l)
-#define insl(p,d,l) __raw_readsl(___io(p),d,l)
-
-#define __is_io_address(p) ((((unsigned long)(p)) & ~(IXP2000_PCI_IO_SIZE - 1)) == IXP2000_PCI_IO_VIRT_BASE)
-
-#define ioread8(p) \
- ({ \
- unsigned int __v; \
- \
- if (__is_io_address(p)) { \
- __v = __raw_readb(alignb(p)); \
- } else { \
- __v = __raw_readb(p); \
- } \
- \
- __v; \
- }) \
-
-#define ioread16(p) \
- ({ \
- unsigned int __v; \
- \
- if (__is_io_address(p)) { \
- __v = __raw_readw(alignw(p)); \
- } else { \
- __v = le16_to_cpu(__raw_readw(p)); \
- } \
- \
- __v; \
- })
-
-#define ioread32(p) \
- ({ \
- unsigned int __v; \
- \
- if (__is_io_address(p)) { \
- __v = __raw_readl(p); \
- } else { \
- __v = le32_to_cpu(__raw_readl(p)); \
- } \
- \
- __v; \
- })
-
-#define iowrite8(v,p) \
- ({ \
- if (__is_io_address(p)) { \
- __raw_writeb((v), alignb(p)); \
- } else { \
- __raw_writeb((v), p); \
- } \
- })
-
-#define iowrite16(v,p) \
- ({ \
- if (__is_io_address(p)) { \
- __raw_writew((v), alignw(p)); \
- } else { \
- __raw_writew(cpu_to_le16(v), p); \
- } \
- })
-
-#define iowrite32(v,p) \
- ({ \
- if (__is_io_address(p)) { \
- __raw_writel((v), p); \
- } else { \
- __raw_writel(cpu_to_le32(v), p); \
- } \
- })
-
-#define ioport_map(port, nr) ___io(port)
-
-#define ioport_unmap(addr)
-#else
-#define __io(p) ((void __iomem *)((p)+IXP2000_PCI_IO_VIRT_BASE))
-#endif
-
-
-#endif
+++ /dev/null
-/*
- * arch/arm/mach-ixp2000/include/mach/irqs.h
- *
- * Original Author: Naeem Afzal <naeem.m.afzal@intel.com>
- * Maintainer: Deepak Saxena <dsaxena@plexity.net>
- *
- * Copyright (C) 2002 Intel Corp.
- * Copyright (C) 2003-2004 MontaVista Software, Inc.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#ifndef _IRQS_H
-#define _IRQS_H
-
-/*
- * Do NOT add #ifdef MACHINE_FOO in here.
- * Simpy add your machine IRQs here and increase NR_IRQS if needed to
- * hold your machine's IRQ table.
- */
-
-/*
- * Some interrupt numbers go unused b/c the IRQ mask/ummask/status
- * register has those bit reserved. We just mark those interrupts
- * as invalid and this allows us to do mask/unmask with a single
- * shift operation instead of having to map the IRQ number to
- * a HW IRQ number.
- */
-#define IRQ_IXP2000_SOFT_INT 0 /* soft interrupt */
-#define IRQ_IXP2000_ERRSUM 1 /* OR of all bits in ErrorStatus reg*/
-#define IRQ_IXP2000_UART 2
-#define IRQ_IXP2000_GPIO 3
-#define IRQ_IXP2000_TIMER1 4
-#define IRQ_IXP2000_TIMER2 5
-#define IRQ_IXP2000_TIMER3 6
-#define IRQ_IXP2000_TIMER4 7
-#define IRQ_IXP2000_PMU 8
-#define IRQ_IXP2000_SPF 9 /* Slow port framer IRQ */
-#define IRQ_IXP2000_DMA1 10
-#define IRQ_IXP2000_DMA2 11
-#define IRQ_IXP2000_DMA3 12
-#define IRQ_IXP2000_PCI_DOORBELL 13
-#define IRQ_IXP2000_ME_ATTN 14
-#define IRQ_IXP2000_PCI 15 /* PCI INTA or INTB */
-#define IRQ_IXP2000_THDA0 16 /* thread 0-31A */
-#define IRQ_IXP2000_THDA1 17 /* thread 32-63A, IXP2800 only */
-#define IRQ_IXP2000_THDA2 18 /* thread 64-95A */
-#define IRQ_IXP2000_THDA3 19 /* thread 96-127A, IXP2800 only */
-#define IRQ_IXP2000_THDB0 24 /* thread 0-31B */
-#define IRQ_IXP2000_THDB1 25 /* thread 32-63B, IXP2800 only */
-#define IRQ_IXP2000_THDB2 26 /* thread 64-95B */
-#define IRQ_IXP2000_THDB3 27 /* thread 96-127B, IXP2800 only */
-
-/* define generic GPIOs */
-#define IRQ_IXP2000_GPIO0 32
-#define IRQ_IXP2000_GPIO1 33
-#define IRQ_IXP2000_GPIO2 34
-#define IRQ_IXP2000_GPIO3 35
-#define IRQ_IXP2000_GPIO4 36
-#define IRQ_IXP2000_GPIO5 37
-#define IRQ_IXP2000_GPIO6 38
-#define IRQ_IXP2000_GPIO7 39
-
-/* split off the 2 PCI sources */
-#define IRQ_IXP2000_PCIA 40
-#define IRQ_IXP2000_PCIB 41
-
-/* Int sources from IRQ_ERROR_STATUS */
-#define IRQ_IXP2000_DRAM0_MIN_ERR 42
-#define IRQ_IXP2000_DRAM0_MAJ_ERR 43
-#define IRQ_IXP2000_DRAM1_MIN_ERR 44
-#define IRQ_IXP2000_DRAM1_MAJ_ERR 45
-#define IRQ_IXP2000_DRAM2_MIN_ERR 46
-#define IRQ_IXP2000_DRAM2_MAJ_ERR 47
-/* 48-57 reserved */
-#define IRQ_IXP2000_SRAM0_ERR 58
-#define IRQ_IXP2000_SRAM1_ERR 59
-#define IRQ_IXP2000_SRAM2_ERR 60
-#define IRQ_IXP2000_SRAM3_ERR 61
-/* 62-65 reserved */
-#define IRQ_IXP2000_MEDIA_ERR 66
-#define IRQ_IXP2000_PCI_ERR 67
-#define IRQ_IXP2000_SP_INT 68
-
-#define NR_IXP2000_IRQS 69
-
-#define IXP2000_BOARD_IRQ(x) (NR_IXP2000_IRQS + (x))
-
-#define IXP2000_BOARD_IRQ_MASK(irq) (1 << (irq - NR_IXP2000_IRQS))
-
-#define IXP2000_ERR_IRQ_MASK(irq) ( 1 << (irq - IRQ_IXP2000_DRAM0_MIN_ERR))
-#define IXP2000_VALID_ERR_IRQ_MASK (\
- IXP2000_ERR_IRQ_MASK(IRQ_IXP2000_DRAM0_MIN_ERR) | \
- IXP2000_ERR_IRQ_MASK(IRQ_IXP2000_DRAM0_MAJ_ERR) | \
- IXP2000_ERR_IRQ_MASK(IRQ_IXP2000_DRAM1_MIN_ERR) | \
- IXP2000_ERR_IRQ_MASK(IRQ_IXP2000_DRAM1_MAJ_ERR) | \
- IXP2000_ERR_IRQ_MASK(IRQ_IXP2000_DRAM2_MIN_ERR) | \
- IXP2000_ERR_IRQ_MASK(IRQ_IXP2000_DRAM2_MAJ_ERR) | \
- IXP2000_ERR_IRQ_MASK(IRQ_IXP2000_SRAM0_ERR) | \
- IXP2000_ERR_IRQ_MASK(IRQ_IXP2000_SRAM1_ERR) | \
- IXP2000_ERR_IRQ_MASK(IRQ_IXP2000_SRAM2_ERR) | \
- IXP2000_ERR_IRQ_MASK(IRQ_IXP2000_SRAM3_ERR) | \
- IXP2000_ERR_IRQ_MASK(IRQ_IXP2000_MEDIA_ERR) | \
- IXP2000_ERR_IRQ_MASK(IRQ_IXP2000_PCI_ERR) | \
- IXP2000_ERR_IRQ_MASK(IRQ_IXP2000_SP_INT) )
-
-/*
- * This allows for all the on-chip sources plus up to 32 CPLD based
- * IRQs. Should be more than enough.
- */
-#define IXP2000_BOARD_IRQS 32
-#define NR_IRQS (NR_IXP2000_IRQS + IXP2000_BOARD_IRQS)
-
-
-/*
- * IXDP2400 specific IRQs
- */
-#define IRQ_IXDP2400_INGRESS_NPU IXP2000_BOARD_IRQ(0)
-#define IRQ_IXDP2400_ENET IXP2000_BOARD_IRQ(1)
-#define IRQ_IXDP2400_MEDIA_PCI IXP2000_BOARD_IRQ(2)
-#define IRQ_IXDP2400_MEDIA_SP IXP2000_BOARD_IRQ(3)
-#define IRQ_IXDP2400_SF_PCI IXP2000_BOARD_IRQ(4)
-#define IRQ_IXDP2400_SF_SP IXP2000_BOARD_IRQ(5)
-#define IRQ_IXDP2400_PMC IXP2000_BOARD_IRQ(6)
-#define IRQ_IXDP2400_TVM IXP2000_BOARD_IRQ(7)
-
-#define NR_IXDP2400_IRQS ((IRQ_IXDP2400_TVM)+1)
-#define IXDP2400_NR_IRQS NR_IXDP2400_IRQS - NR_IXP2000_IRQS
-
-/* IXDP2800 specific IRQs */
-#define IRQ_IXDP2800_EGRESS_ENET IXP2000_BOARD_IRQ(0)
-#define IRQ_IXDP2800_INGRESS_NPU IXP2000_BOARD_IRQ(1)
-#define IRQ_IXDP2800_PMC IXP2000_BOARD_IRQ(2)
-#define IRQ_IXDP2800_FABRIC_PCI IXP2000_BOARD_IRQ(3)
-#define IRQ_IXDP2800_FABRIC IXP2000_BOARD_IRQ(4)
-#define IRQ_IXDP2800_MEDIA IXP2000_BOARD_IRQ(5)
-
-#define NR_IXDP2800_IRQS ((IRQ_IXDP2800_MEDIA)+1)
-#define IXDP2800_NR_IRQS NR_IXDP2800_IRQS - NR_IXP2000_IRQS
-
-/*
- * IRQs on both IXDP2x01 boards
- */
-#define IRQ_IXDP2X01_SPCI_DB_0 IXP2000_BOARD_IRQ(2)
-#define IRQ_IXDP2X01_SPCI_DB_1 IXP2000_BOARD_IRQ(3)
-#define IRQ_IXDP2X01_SPCI_PMC_INTA IXP2000_BOARD_IRQ(4)
-#define IRQ_IXDP2X01_SPCI_PMC_INTB IXP2000_BOARD_IRQ(5)
-#define IRQ_IXDP2X01_SPCI_PMC_INTC IXP2000_BOARD_IRQ(6)
-#define IRQ_IXDP2X01_SPCI_PMC_INTD IXP2000_BOARD_IRQ(7)
-#define IRQ_IXDP2X01_SPCI_FIC_INT IXP2000_BOARD_IRQ(8)
-#define IRQ_IXDP2X01_IPMI_FROM IXP2000_BOARD_IRQ(16)
-#define IRQ_IXDP2X01_125US IXP2000_BOARD_IRQ(17)
-#define IRQ_IXDP2X01_DB_0_ADD IXP2000_BOARD_IRQ(18)
-#define IRQ_IXDP2X01_DB_1_ADD IXP2000_BOARD_IRQ(19)
-#define IRQ_IXDP2X01_UART1 IXP2000_BOARD_IRQ(21)
-#define IRQ_IXDP2X01_UART2 IXP2000_BOARD_IRQ(22)
-#define IRQ_IXDP2X01_FIC_ADD_INT IXP2000_BOARD_IRQ(24)
-#define IRQ_IXDP2X01_CS8900 IXP2000_BOARD_IRQ(25)
-#define IRQ_IXDP2X01_BBSRAM IXP2000_BOARD_IRQ(26)
-
-#define IXDP2X01_VALID_IRQ_MASK ( \
- IXP2000_BOARD_IRQ_MASK(IRQ_IXDP2X01_SPCI_DB_0) | \
- IXP2000_BOARD_IRQ_MASK(IRQ_IXDP2X01_SPCI_DB_1) | \
- IXP2000_BOARD_IRQ_MASK(IRQ_IXDP2X01_SPCI_PMC_INTA) | \
- IXP2000_BOARD_IRQ_MASK(IRQ_IXDP2X01_SPCI_PMC_INTB) | \
- IXP2000_BOARD_IRQ_MASK(IRQ_IXDP2X01_SPCI_PMC_INTC) | \
- IXP2000_BOARD_IRQ_MASK(IRQ_IXDP2X01_SPCI_PMC_INTD) | \
- IXP2000_BOARD_IRQ_MASK(IRQ_IXDP2X01_SPCI_FIC_INT) | \
- IXP2000_BOARD_IRQ_MASK(IRQ_IXDP2X01_IPMI_FROM) | \
- IXP2000_BOARD_IRQ_MASK(IRQ_IXDP2X01_125US) | \
- IXP2000_BOARD_IRQ_MASK(IRQ_IXDP2X01_DB_0_ADD) | \
- IXP2000_BOARD_IRQ_MASK(IRQ_IXDP2X01_DB_1_ADD) | \
- IXP2000_BOARD_IRQ_MASK(IRQ_IXDP2X01_UART1) | \
- IXP2000_BOARD_IRQ_MASK(IRQ_IXDP2X01_UART2) | \
- IXP2000_BOARD_IRQ_MASK(IRQ_IXDP2X01_FIC_ADD_INT) | \
- IXP2000_BOARD_IRQ_MASK(IRQ_IXDP2X01_CS8900) | \
- IXP2000_BOARD_IRQ_MASK(IRQ_IXDP2X01_BBSRAM) )
-
-/*
- * IXDP2401 specific IRQs
- */
-#define IRQ_IXDP2401_INTA_82546 IXP2000_BOARD_IRQ(0)
-#define IRQ_IXDP2401_INTB_82546 IXP2000_BOARD_IRQ(1)
-
-#define IXDP2401_VALID_IRQ_MASK ( \
- IXDP2X01_VALID_IRQ_MASK | \
- IXP2000_BOARD_IRQ_MASK(IRQ_IXDP2401_INTA_82546) |\
- IXP2000_BOARD_IRQ_MASK(IRQ_IXDP2401_INTB_82546))
-
-/*
- * IXDP2801-specific IRQs
- */
-#define IRQ_IXDP2801_RIV IXP2000_BOARD_IRQ(0)
-#define IRQ_IXDP2801_CNFG_MEDIA IXP2000_BOARD_IRQ(27)
-#define IRQ_IXDP2801_CLOCK_REF IXP2000_BOARD_IRQ(28)
-
-#define IXDP2801_VALID_IRQ_MASK ( \
- IXDP2X01_VALID_IRQ_MASK | \
- IXP2000_BOARD_IRQ_MASK(IRQ_IXDP2801_RIV) |\
- IXP2000_BOARD_IRQ_MASK(IRQ_IXDP2801_CNFG_MEDIA) |\
- IXP2000_BOARD_IRQ_MASK(IRQ_IXDP2801_CLOCK_REF))
-
-#define NR_IXDP2X01_IRQS ((IRQ_IXDP2801_CLOCK_REF) + 1)
-
-#endif /*_IRQS_H*/
+++ /dev/null
-/*
- * arch/arm/mach-ixp2000/include/mach/ixdp2x00.h
- *
- * Register and other defines for IXDP2[48]00 platforms
- *
- * Original Author: Naeem Afzal <naeem.m.afzal@intel.com>
- * Maintainer: Deepak Saxena <dsaxena@plexity.net>
- *
- * Copyright (C) 2002 Intel Corp.
- * Copyright (C) 2003-2004 MontaVista Software, Inc.
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- */
-#ifndef _IXDP2X00_H_
-#define _IXDP2X00_H_
-
-/*
- * On board CPLD memory map
- */
-#define IXDP2X00_PHYS_CPLD_BASE 0xc7000000
-#define IXDP2X00_VIRT_CPLD_BASE 0xfe000000
-#define IXDP2X00_CPLD_SIZE 0x00100000
-
-
-#define IXDP2X00_CPLD_REG(x) \
- (volatile unsigned long *)(IXDP2X00_VIRT_CPLD_BASE | x)
-
-/*
- * IXDP2400 CPLD registers
- */
-#define IXDP2400_CPLD_SYSLED IXDP2X00_CPLD_REG(0x0)
-#define IXDP2400_CPLD_DISP_DATA IXDP2X00_CPLD_REG(0x4)
-#define IXDP2400_CPLD_CLOCK_SPEED IXDP2X00_CPLD_REG(0x8)
-#define IXDP2400_CPLD_INT_STAT IXDP2X00_CPLD_REG(0xc)
-#define IXDP2400_CPLD_REV IXDP2X00_CPLD_REG(0x10)
-#define IXDP2400_CPLD_SYS_CLK_M IXDP2X00_CPLD_REG(0x14)
-#define IXDP2400_CPLD_SYS_CLK_N IXDP2X00_CPLD_REG(0x18)
-#define IXDP2400_CPLD_INT_MASK IXDP2X00_CPLD_REG(0x48)
-
-/*
- * IXDP2800 CPLD registers
- */
-#define IXDP2800_CPLD_INT_STAT IXDP2X00_CPLD_REG(0x0)
-#define IXDP2800_CPLD_INT_MASK IXDP2X00_CPLD_REG(0x140)
-
-
-#define IXDP2X00_GPIO_I2C_ENABLE 0x02
-#define IXDP2X00_GPIO_SCL 0x07
-#define IXDP2X00_GPIO_SDA 0x06
-
-/*
- * PCI devfns for on-board devices. We need these to be able to
- * properly translate IRQs and for device removal.
- */
-#define IXDP2400_SLAVE_ENET_DEVFN 0x18 /* Bus 1 */
-#define IXDP2400_MASTER_ENET_DEVFN 0x20 /* Bus 1 */
-#define IXDP2400_MEDIA_DEVFN 0x28 /* Bus 1 */
-#define IXDP2400_SWITCH_FABRIC_DEVFN 0x30 /* Bus 1 */
-
-#define IXDP2800_SLAVE_ENET_DEVFN 0x20 /* Bus 1 */
-#define IXDP2800_MASTER_ENET_DEVFN 0x18 /* Bus 1 */
-#define IXDP2800_SWITCH_FABRIC_DEVFN 0x30 /* Bus 1 */
-
-#define IXDP2X00_P2P_DEVFN 0x20 /* Bus 0 */
-#define IXDP2X00_21555_DEVFN 0x30 /* Bus 0 */
-#define IXDP2X00_SLAVE_NPU_DEVFN 0x28 /* Bus 1 */
-#define IXDP2X00_PMC_DEVFN 0x38 /* Bus 1 */
-#define IXDP2X00_MASTER_NPU_DEVFN 0x38 /* Bus 1 */
-
-#ifndef __ASSEMBLY__
-/*
- * The master NPU is always PCI master.
- */
-static inline unsigned int ixdp2x00_master_npu(void)
-{
- return !!ixp2000_is_pcimaster();
-}
-
-/*
- * Helper functions used by ixdp2400 and ixdp2800 specific code
- */
-void ixdp2x00_init_irq(volatile unsigned long*, volatile unsigned long *, unsigned long);
-void ixdp2x00_slave_pci_postinit(void);
-void ixdp2x00_init_machine(void);
-void ixdp2x00_map_io(void);
-
-#endif
-
-#endif /*_IXDP2X00_H_ */
+++ /dev/null
-/*
- * arch/arm/mach-ixp2000/include/mach/ixdp2x01.h
- *
- * Platform definitions for IXDP2X01 && IXDP2801 systems
- *
- * Author: Deepak Saxena <dsaxena@plexity.net>
- *
- * Copyright 2004 (c) MontaVista Software, Inc.
- *
- * Based on original code Copyright (c) 2002-2003 Intel Corporation
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#ifndef __IXDP2X01_H__
-#define __IXDP2X01_H__
-
-#define IXDP2X01_PHYS_CPLD_BASE 0xc6024000
-#define IXDP2X01_VIRT_CPLD_BASE 0xfe000000
-#define IXDP2X01_CPLD_REGION_SIZE 0x00100000
-
-#define IXDP2X01_CPLD_VIRT_REG(reg) (volatile unsigned long*)(IXDP2X01_VIRT_CPLD_BASE | reg)
-#define IXDP2X01_CPLD_PHYS_REG(reg) (IXDP2X01_PHYS_CPLD_BASE | reg)
-
-#define IXDP2X01_UART1_VIRT_BASE IXDP2X01_CPLD_VIRT_REG(0x40)
-#define IXDP2X01_UART1_PHYS_BASE IXDP2X01_CPLD_PHYS_REG(0x40)
-
-#define IXDP2X01_UART2_VIRT_BASE IXDP2X01_CPLD_VIRT_REG(0x60)
-#define IXDP2X01_UART2_PHYS_BASE IXDP2X01_CPLD_PHYS_REG(0x60)
-
-#define IXDP2X01_CS8900_VIRT_BASE IXDP2X01_CPLD_VIRT_REG(0x80)
-#define IXDP2X01_CS8900_VIRT_END (IXDP2X01_CS8900_VIRT_BASE + 16)
-
-#define IXDP2X01_CPLD_RESET_REG IXDP2X01_CPLD_VIRT_REG(0x00)
-#define IXDP2X01_INT_MASK_SET_REG IXDP2X01_CPLD_VIRT_REG(0x08)
-#define IXDP2X01_INT_STAT_REG IXDP2X01_CPLD_VIRT_REG(0x0C)
-#define IXDP2X01_INT_RAW_REG IXDP2X01_CPLD_VIRT_REG(0x10)
-#define IXDP2X01_INT_MASK_CLR_REG IXDP2X01_INT_RAW_REG
-#define IXDP2X01_INT_SIM_REG IXDP2X01_CPLD_VIRT_REG(0x14)
-
-#define IXDP2X01_CPLD_FLASH_REG IXDP2X01_CPLD_VIRT_REG(0x20)
-
-#define IXDP2X01_CPLD_FLASH_INTERN 0x8000
-#define IXDP2X01_CPLD_FLASH_BANK_MASK 0xF
-#define IXDP2X01_FLASH_WINDOW_BITS 25
-#define IXDP2X01_FLASH_WINDOW_SIZE (1 << IXDP2X01_FLASH_WINDOW_BITS)
-#define IXDP2X01_FLASH_WINDOW_MASK (IXDP2X01_FLASH_WINDOW_SIZE - 1)
-
-#define IXDP2X01_UART_CLK 1843200
-
-#define IXDP2X01_GPIO_I2C_ENABLE 0x02
-#define IXDP2X01_GPIO_SCL 0x07
-#define IXDP2X01_GPIO_SDA 0x06
-
-#endif /* __IXDP2x01_H__ */
+++ /dev/null
-/*
- * arch/arm/mach-ixp2000/include/mach/ixp2000-regs.h
- *
- * Chipset register definitions for IXP2400/2800 based systems.
- *
- * Original Author: Naeem Afzal <naeem.m.afzal@intel.com>
- *
- * Maintainer: Deepak Saxena <dsaxena@plexity.net>
- *
- * Copyright (C) 2002 Intel Corp.
- * Copyright (C) 2003-2004 MontaVista Software, Inc.
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- */
-#ifndef _IXP2000_REGS_H_
-#define _IXP2000_REGS_H_
-
-/*
- * IXP2000 linux memory map:
- *
- * virt phys size
- * fb000000 db000000 16M PCI CFG1
- * fc000000 da000000 16M PCI CFG0
- * fd000000 d8000000 16M PCI I/O
- * fe[0-7]00000 8M per-platform mappings
- * fe900000 80000000 1M SRAM #0 (first MB)
- * fea00000 cb400000 1M SCRATCH ring get/put
- * feb00000 c8000000 1M MSF
- * fec00000 df000000 1M PCI CSRs
- * fed00000 de000000 1M PCI CREG
- * fee00000 d6000000 1M INTCTL
- * fef00000 c0000000 1M CAP
- */
-
-/*
- * Static I/O regions.
- *
- * Most of the registers are clumped in 4K regions spread throughout
- * the 0xc0000000 -> 0xc0100000 address range, but we just map in
- * the whole range using a single 1 MB section instead of small
- * 4K pages.
- *
- * CAP stands for CSR Access Proxy.
- *
- * If you change the virtual address of this mapping, please propagate
- * the change to arch/arm/kernel/debug.S, which hardcodes the virtual
- * address of the UART located in this region.
- */
-
-#define IXP2000_CAP_PHYS_BASE 0xc0000000
-#define IXP2000_CAP_VIRT_BASE 0xfef00000
-#define IXP2000_CAP_SIZE 0x00100000
-
-/*
- * Addresses for specific on-chip peripherals.
- */
-#define IXP2000_SLOWPORT_CSR_VIRT_BASE 0xfef80000
-#define IXP2000_GLOBAL_REG_VIRT_BASE 0xfef04000
-#define IXP2000_UART_PHYS_BASE 0xc0030000
-#define IXP2000_UART_VIRT_BASE 0xfef30000
-#define IXP2000_TIMER_VIRT_BASE 0xfef20000
-#define IXP2000_UENGINE_CSR_VIRT_BASE 0xfef18000
-#define IXP2000_GPIO_VIRT_BASE 0xfef10000
-
-/*
- * Devices outside of the 0xc0000000 -> 0xc0100000 range. The virtual
- * addresses of the INTCTL and PCI_CSR mappings are hardcoded in
- * entry-macro.S, so if you ever change these please propagate
- * the change.
- */
-#define IXP2000_INTCTL_PHYS_BASE 0xd6000000
-#define IXP2000_INTCTL_VIRT_BASE 0xfee00000
-#define IXP2000_INTCTL_SIZE 0x00100000
-
-#define IXP2000_PCI_CREG_PHYS_BASE 0xde000000
-#define IXP2000_PCI_CREG_VIRT_BASE 0xfed00000
-#define IXP2000_PCI_CREG_SIZE 0x00100000
-
-#define IXP2000_PCI_CSR_PHYS_BASE 0xdf000000
-#define IXP2000_PCI_CSR_VIRT_BASE 0xfec00000
-#define IXP2000_PCI_CSR_SIZE 0x00100000
-
-#define IXP2000_MSF_PHYS_BASE 0xc8000000
-#define IXP2000_MSF_VIRT_BASE 0xfeb00000
-#define IXP2000_MSF_SIZE 0x00100000
-
-#define IXP2000_SCRATCH_RING_PHYS_BASE 0xcb400000
-#define IXP2000_SCRATCH_RING_VIRT_BASE 0xfea00000
-#define IXP2000_SCRATCH_RING_SIZE 0x00100000
-
-#define IXP2000_SRAM0_PHYS_BASE 0x80000000
-#define IXP2000_SRAM0_VIRT_BASE 0xfe900000
-#define IXP2000_SRAM0_SIZE 0x00100000
-
-#define IXP2000_PCI_IO_PHYS_BASE 0xd8000000
-#define IXP2000_PCI_IO_VIRT_BASE 0xfd000000
-#define IXP2000_PCI_IO_SIZE 0x01000000
-
-#define IXP2000_PCI_CFG0_PHYS_BASE 0xda000000
-#define IXP2000_PCI_CFG0_VIRT_BASE 0xfc000000
-#define IXP2000_PCI_CFG0_SIZE 0x01000000
-
-#define IXP2000_PCI_CFG1_PHYS_BASE 0xdb000000
-#define IXP2000_PCI_CFG1_VIRT_BASE 0xfb000000
-#define IXP2000_PCI_CFG1_SIZE 0x01000000
-
-/*
- * Timers
- */
-#define IXP2000_TIMER_REG(x) ((volatile unsigned long*)(IXP2000_TIMER_VIRT_BASE | (x)))
-/* Timer control */
-#define IXP2000_T1_CTL IXP2000_TIMER_REG(0x00)
-#define IXP2000_T2_CTL IXP2000_TIMER_REG(0x04)
-#define IXP2000_T3_CTL IXP2000_TIMER_REG(0x08)
-#define IXP2000_T4_CTL IXP2000_TIMER_REG(0x0c)
-/* Store initial value */
-#define IXP2000_T1_CLD IXP2000_TIMER_REG(0x10)
-#define IXP2000_T2_CLD IXP2000_TIMER_REG(0x14)
-#define IXP2000_T3_CLD IXP2000_TIMER_REG(0x18)
-#define IXP2000_T4_CLD IXP2000_TIMER_REG(0x1c)
-/* Read current value */
-#define IXP2000_T1_CSR IXP2000_TIMER_REG(0x20)
-#define IXP2000_T2_CSR IXP2000_TIMER_REG(0x24)
-#define IXP2000_T3_CSR IXP2000_TIMER_REG(0x28)
-#define IXP2000_T4_CSR IXP2000_TIMER_REG(0x2c)
-/* Clear associated timer interrupt */
-#define IXP2000_T1_CLR IXP2000_TIMER_REG(0x30)
-#define IXP2000_T2_CLR IXP2000_TIMER_REG(0x34)
-#define IXP2000_T3_CLR IXP2000_TIMER_REG(0x38)
-#define IXP2000_T4_CLR IXP2000_TIMER_REG(0x3c)
-/* Timer watchdog enable for T4 */
-#define IXP2000_TWDE IXP2000_TIMER_REG(0x40)
-
-#define WDT_ENABLE 0x00000001
-#define TIMER_DIVIDER_256 0x00000008
-#define TIMER_ENABLE 0x00000080
-#define IRQ_MASK_TIMER1 (1 << 4)
-
-/*
- * Interrupt controller registers
- */
-#define IXP2000_INTCTL_REG(x) (volatile unsigned long*)(IXP2000_INTCTL_VIRT_BASE | (x))
-#define IXP2000_IRQ_STATUS IXP2000_INTCTL_REG(0x08)
-#define IXP2000_IRQ_ENABLE IXP2000_INTCTL_REG(0x10)
-#define IXP2000_IRQ_ENABLE_SET IXP2000_INTCTL_REG(0x10)
-#define IXP2000_IRQ_ENABLE_CLR IXP2000_INTCTL_REG(0x18)
-#define IXP2000_FIQ_ENABLE_CLR IXP2000_INTCTL_REG(0x14)
-#define IXP2000_IRQ_ERR_STATUS IXP2000_INTCTL_REG(0x24)
-#define IXP2000_IRQ_ERR_ENABLE_SET IXP2000_INTCTL_REG(0x2c)
-#define IXP2000_FIQ_ERR_ENABLE_CLR IXP2000_INTCTL_REG(0x30)
-#define IXP2000_IRQ_ERR_ENABLE_CLR IXP2000_INTCTL_REG(0x34)
-#define IXP2000_IRQ_THD_RAW_STATUS_A_0 IXP2000_INTCTL_REG(0x60)
-#define IXP2000_IRQ_THD_RAW_STATUS_A_1 IXP2000_INTCTL_REG(0x64)
-#define IXP2000_IRQ_THD_RAW_STATUS_A_2 IXP2000_INTCTL_REG(0x68)
-#define IXP2000_IRQ_THD_RAW_STATUS_A_3 IXP2000_INTCTL_REG(0x6c)
-#define IXP2000_IRQ_THD_RAW_STATUS_B_0 IXP2000_INTCTL_REG(0x80)
-#define IXP2000_IRQ_THD_RAW_STATUS_B_1 IXP2000_INTCTL_REG(0x84)
-#define IXP2000_IRQ_THD_RAW_STATUS_B_2 IXP2000_INTCTL_REG(0x88)
-#define IXP2000_IRQ_THD_RAW_STATUS_B_3 IXP2000_INTCTL_REG(0x8c)
-#define IXP2000_IRQ_THD_STATUS_A_0 IXP2000_INTCTL_REG(0xe0)
-#define IXP2000_IRQ_THD_STATUS_A_1 IXP2000_INTCTL_REG(0xe4)
-#define IXP2000_IRQ_THD_STATUS_A_2 IXP2000_INTCTL_REG(0xe8)
-#define IXP2000_IRQ_THD_STATUS_A_3 IXP2000_INTCTL_REG(0xec)
-#define IXP2000_IRQ_THD_STATUS_B_0 IXP2000_INTCTL_REG(0x100)
-#define IXP2000_IRQ_THD_STATUS_B_1 IXP2000_INTCTL_REG(0x104)
-#define IXP2000_IRQ_THD_STATUS_B_2 IXP2000_INTCTL_REG(0x108)
-#define IXP2000_IRQ_THD_STATUS_B_3 IXP2000_INTCTL_REG(0x10c)
-#define IXP2000_IRQ_THD_ENABLE_SET_A_0 IXP2000_INTCTL_REG(0x160)
-#define IXP2000_IRQ_THD_ENABLE_SET_A_1 IXP2000_INTCTL_REG(0x164)
-#define IXP2000_IRQ_THD_ENABLE_SET_A_2 IXP2000_INTCTL_REG(0x168)
-#define IXP2000_IRQ_THD_ENABLE_SET_A_3 IXP2000_INTCTL_REG(0x16c)
-#define IXP2000_IRQ_THD_ENABLE_SET_B_0 IXP2000_INTCTL_REG(0x180)
-#define IXP2000_IRQ_THD_ENABLE_SET_B_1 IXP2000_INTCTL_REG(0x184)
-#define IXP2000_IRQ_THD_ENABLE_SET_B_2 IXP2000_INTCTL_REG(0x188)
-#define IXP2000_IRQ_THD_ENABLE_SET_B_3 IXP2000_INTCTL_REG(0x18c)
-#define IXP2000_IRQ_THD_ENABLE_CLEAR_A_0 IXP2000_INTCTL_REG(0x1e0)
-#define IXP2000_IRQ_THD_ENABLE_CLEAR_A_1 IXP2000_INTCTL_REG(0x1e4)
-#define IXP2000_IRQ_THD_ENABLE_CLEAR_A_2 IXP2000_INTCTL_REG(0x1e8)
-#define IXP2000_IRQ_THD_ENABLE_CLEAR_A_3 IXP2000_INTCTL_REG(0x1ec)
-#define IXP2000_IRQ_THD_ENABLE_CLEAR_B_0 IXP2000_INTCTL_REG(0x200)
-#define IXP2000_IRQ_THD_ENABLE_CLEAR_B_1 IXP2000_INTCTL_REG(0x204)
-#define IXP2000_IRQ_THD_ENABLE_CLEAR_B_2 IXP2000_INTCTL_REG(0x208)
-#define IXP2000_IRQ_THD_ENABLE_CLEAR_B_3 IXP2000_INTCTL_REG(0x20c)
-
-/*
- * Mask of valid IRQs in the 32-bit IRQ register. We use
- * this to mark certain IRQs as being invalid.
- */
-#define IXP2000_VALID_IRQ_MASK 0x0f0fffff
-
-/*
- * PCI config register access from core
- */
-#define IXP2000_PCI_CREG(x) (volatile unsigned long*)(IXP2000_PCI_CREG_VIRT_BASE | (x))
-#define IXP2000_PCI_CMDSTAT IXP2000_PCI_CREG(0x04)
-#define IXP2000_PCI_CSR_BAR IXP2000_PCI_CREG(0x10)
-#define IXP2000_PCI_SRAM_BAR IXP2000_PCI_CREG(0x14)
-#define IXP2000_PCI_SDRAM_BAR IXP2000_PCI_CREG(0x18)
-
-/*
- * PCI CSRs
- */
-#define IXP2000_PCI_CSR(x) (volatile unsigned long*)(IXP2000_PCI_CSR_VIRT_BASE | (x))
-
-/*
- * PCI outbound interrupts
- */
-#define IXP2000_PCI_OUT_INT_STATUS IXP2000_PCI_CSR(0x30)
-#define IXP2000_PCI_OUT_INT_MASK IXP2000_PCI_CSR(0x34)
-/*
- * PCI communications
- */
-#define IXP2000_PCI_MAILBOX0 IXP2000_PCI_CSR(0x50)
-#define IXP2000_PCI_MAILBOX1 IXP2000_PCI_CSR(0x54)
-#define IXP2000_PCI_MAILBOX2 IXP2000_PCI_CSR(0x58)
-#define IXP2000_PCI_MAILBOX3 IXP2000_PCI_CSR(0x5C)
-#define IXP2000_XSCALE_DOORBELL IXP2000_PCI_CSR(0x60)
-#define IXP2000_XSCALE_DOORBELL_SETUP IXP2000_PCI_CSR(0x64)
-#define IXP2000_PCI_DOORBELL IXP2000_PCI_CSR(0x70)
-#define IXP2000_PCI_DOORBELL_SETUP IXP2000_PCI_CSR(0x74)
-
-/*
- * DMA engines
- */
-#define IXP2000_PCI_CH1_BYTE_CNT IXP2000_PCI_CSR(0x80)
-#define IXP2000_PCI_CH1_ADDR IXP2000_PCI_CSR(0x84)
-#define IXP2000_PCI_CH1_DRAM_ADDR IXP2000_PCI_CSR(0x88)
-#define IXP2000_PCI_CH1_DESC_PTR IXP2000_PCI_CSR(0x8C)
-#define IXP2000_PCI_CH1_CNTRL IXP2000_PCI_CSR(0x90)
-#define IXP2000_PCI_CH1_ME_PARAM IXP2000_PCI_CSR(0x94)
-#define IXP2000_PCI_CH2_BYTE_CNT IXP2000_PCI_CSR(0xA0)
-#define IXP2000_PCI_CH2_ADDR IXP2000_PCI_CSR(0xA4)
-#define IXP2000_PCI_CH2_DRAM_ADDR IXP2000_PCI_CSR(0xA8)
-#define IXP2000_PCI_CH2_DESC_PTR IXP2000_PCI_CSR(0xAC)
-#define IXP2000_PCI_CH2_CNTRL IXP2000_PCI_CSR(0xB0)
-#define IXP2000_PCI_CH2_ME_PARAM IXP2000_PCI_CSR(0xB4)
-#define IXP2000_PCI_CH3_BYTE_CNT IXP2000_PCI_CSR(0xC0)
-#define IXP2000_PCI_CH3_ADDR IXP2000_PCI_CSR(0xC4)
-#define IXP2000_PCI_CH3_DRAM_ADDR IXP2000_PCI_CSR(0xC8)
-#define IXP2000_PCI_CH3_DESC_PTR IXP2000_PCI_CSR(0xCC)
-#define IXP2000_PCI_CH3_CNTRL IXP2000_PCI_CSR(0xD0)
-#define IXP2000_PCI_CH3_ME_PARAM IXP2000_PCI_CSR(0xD4)
-#define IXP2000_DMA_INF_MODE IXP2000_PCI_CSR(0xE0)
-/*
- * Size masks for BARs
- */
-#define IXP2000_PCI_SRAM_BASE_ADDR_MASK IXP2000_PCI_CSR(0xFC)
-#define IXP2000_PCI_DRAM_BASE_ADDR_MASK IXP2000_PCI_CSR(0x100)
-/*
- * Control and uEngine related
- */
-#define IXP2000_PCI_CONTROL IXP2000_PCI_CSR(0x13C)
-#define IXP2000_PCI_ADDR_EXT IXP2000_PCI_CSR(0x140)
-#define IXP2000_PCI_ME_PUSH_STATUS IXP2000_PCI_CSR(0x148)
-#define IXP2000_PCI_ME_PUSH_EN IXP2000_PCI_CSR(0x14C)
-#define IXP2000_PCI_ERR_STATUS IXP2000_PCI_CSR(0x150)
-#define IXP2000_PCI_ERR_ENABLE IXP2000_PCI_CSR(0x154)
-/*
- * Inbound PCI interrupt control
- */
-#define IXP2000_PCI_XSCALE_INT_STATUS IXP2000_PCI_CSR(0x158)
-#define IXP2000_PCI_XSCALE_INT_ENABLE IXP2000_PCI_CSR(0x15C)
-
-#define IXP2000_PCICNTL_PNR (1<<17) /* PCI not Reset bit of PCI_CONTROL */
-#define IXP2000_PCICNTL_PCF (1<<28) /* PCI Central function bit */
-#define IXP2000_XSCALE_INT (1<<1) /* Interrupt from XScale to PCI */
-
-/* These are from the IRQ register in the PCI ISR register */
-#define PCI_CONTROL_BE_DEO (1 << 22) /* Big Endian Data Enable Out */
-#define PCI_CONTROL_BE_DEI (1 << 21) /* Big Endian Data Enable In */
-#define PCI_CONTROL_BE_BEO (1 << 20) /* Big Endian Byte Enable Out */
-#define PCI_CONTROL_BE_BEI (1 << 19) /* Big Endian Byte Enable In */
-#define PCI_CONTROL_IEE (1 << 17) /* I/O cycle Endian swap Enable */
-
-#define IXP2000_PCI_RST_REL (1 << 2)
-#define CFG_RST_DIR (*IXP2000_PCI_CONTROL & IXP2000_PCICNTL_PCF)
-#define CFG_PCI_BOOT_HOST (1 << 2)
-#define CFG_BOOT_PROM (1 << 1)
-
-/*
- * SlowPort CSRs
- *
- * The slowport is used to access things like flash, SONET framer control
- * ports, slave microprocessors, CPLDs, and others of chip memory mapped
- * peripherals.
- */
-#define SLOWPORT_CSR(x) (volatile unsigned long*)(IXP2000_SLOWPORT_CSR_VIRT_BASE | (x))
-
-#define IXP2000_SLOWPORT_CCR SLOWPORT_CSR(0x00)
-#define IXP2000_SLOWPORT_WTC1 SLOWPORT_CSR(0x04)
-#define IXP2000_SLOWPORT_WTC2 SLOWPORT_CSR(0x08)
-#define IXP2000_SLOWPORT_RTC1 SLOWPORT_CSR(0x0c)
-#define IXP2000_SLOWPORT_RTC2 SLOWPORT_CSR(0x10)
-#define IXP2000_SLOWPORT_FSR SLOWPORT_CSR(0x14)
-#define IXP2000_SLOWPORT_PCR SLOWPORT_CSR(0x18)
-#define IXP2000_SLOWPORT_ADC SLOWPORT_CSR(0x1C)
-#define IXP2000_SLOWPORT_FAC SLOWPORT_CSR(0x20)
-#define IXP2000_SLOWPORT_FRM SLOWPORT_CSR(0x24)
-#define IXP2000_SLOWPORT_FIN SLOWPORT_CSR(0x28)
-
-/*
- * CCR values.
- * The CCR configures the clock division for the slowport interface.
- */
-#define SLOWPORT_CCR_DIV_1 0x00
-#define SLOWPORT_CCR_DIV_2 0x01
-#define SLOWPORT_CCR_DIV_4 0x02
-#define SLOWPORT_CCR_DIV_6 0x03
-#define SLOWPORT_CCR_DIV_8 0x04
-#define SLOWPORT_CCR_DIV_10 0x05
-#define SLOWPORT_CCR_DIV_12 0x06
-#define SLOWPORT_CCR_DIV_14 0x07
-#define SLOWPORT_CCR_DIV_16 0x08
-#define SLOWPORT_CCR_DIV_18 0x09
-#define SLOWPORT_CCR_DIV_20 0x0a
-#define SLOWPORT_CCR_DIV_22 0x0b
-#define SLOWPORT_CCR_DIV_24 0x0c
-#define SLOWPORT_CCR_DIV_26 0x0d
-#define SLOWPORT_CCR_DIV_28 0x0e
-#define SLOWPORT_CCR_DIV_30 0x0f
-
-/*
- * PCR values. PCR configure the mode of the interface.
- */
-#define SLOWPORT_MODE_FLASH 0x00
-#define SLOWPORT_MODE_LUCENT 0x01
-#define SLOWPORT_MODE_PMC_SIERRA 0x02
-#define SLOWPORT_MODE_INTEL_UP 0x03
-#define SLOWPORT_MODE_MOTOROLA_UP 0x04
-
-/*
- * ADC values. Defines data and address bus widths.
- */
-#define SLOWPORT_ADDR_WIDTH_8 0x00
-#define SLOWPORT_ADDR_WIDTH_16 0x01
-#define SLOWPORT_ADDR_WIDTH_24 0x02
-#define SLOWPORT_ADDR_WIDTH_32 0x03
-#define SLOWPORT_DATA_WIDTH_8 0x00
-#define SLOWPORT_DATA_WIDTH_16 0x10
-#define SLOWPORT_DATA_WIDTH_24 0x20
-#define SLOWPORT_DATA_WIDTH_32 0x30
-
-/*
- * Masks and shifts for various fields in the WTC and RTC registers.
- */
-#define SLOWPORT_WRTC_MASK_HD 0x0003
-#define SLOWPORT_WRTC_MASK_PW 0x003c
-#define SLOWPORT_WRTC_MASK_SU 0x03c0
-
-#define SLOWPORT_WRTC_SHIFT_HD 0x00
-#define SLOWPORT_WRTC_SHIFT_SU 0x02
-#define SLOWPORT_WRTC_SHFIT_PW 0x06
-
-
-/*
- * GPIO registers & GPIO interface.
- */
-#define IXP2000_GPIO_REG(x) ((volatile unsigned long*)(IXP2000_GPIO_VIRT_BASE+(x)))
-#define IXP2000_GPIO_PLR IXP2000_GPIO_REG(0x00)
-#define IXP2000_GPIO_PDPR IXP2000_GPIO_REG(0x04)
-#define IXP2000_GPIO_PDSR IXP2000_GPIO_REG(0x08)
-#define IXP2000_GPIO_PDCR IXP2000_GPIO_REG(0x0c)
-#define IXP2000_GPIO_POPR IXP2000_GPIO_REG(0x10)
-#define IXP2000_GPIO_POSR IXP2000_GPIO_REG(0x14)
-#define IXP2000_GPIO_POCR IXP2000_GPIO_REG(0x18)
-#define IXP2000_GPIO_REDR IXP2000_GPIO_REG(0x1c)
-#define IXP2000_GPIO_FEDR IXP2000_GPIO_REG(0x20)
-#define IXP2000_GPIO_EDSR IXP2000_GPIO_REG(0x24)
-#define IXP2000_GPIO_LSHR IXP2000_GPIO_REG(0x28)
-#define IXP2000_GPIO_LSLR IXP2000_GPIO_REG(0x2c)
-#define IXP2000_GPIO_LDSR IXP2000_GPIO_REG(0x30)
-#define IXP2000_GPIO_INER IXP2000_GPIO_REG(0x34)
-#define IXP2000_GPIO_INSR IXP2000_GPIO_REG(0x38)
-#define IXP2000_GPIO_INCR IXP2000_GPIO_REG(0x3c)
-#define IXP2000_GPIO_INST IXP2000_GPIO_REG(0x40)
-
-/*
- * "Global" registers...whatever that's supposed to mean.
- */
-#define GLOBAL_REG_BASE (IXP2000_GLOBAL_REG_VIRT_BASE + 0x0a00)
-#define GLOBAL_REG(x) (volatile unsigned long*)(GLOBAL_REG_BASE | (x))
-
-#define IXP2000_MAJ_PROD_TYPE_MASK 0x001F0000
-#define IXP2000_MAJ_PROD_TYPE_IXP2000 0x00000000
-#define IXP2000_MIN_PROD_TYPE_MASK 0x0000FF00
-#define IXP2000_MIN_PROD_TYPE_IXP2400 0x00000200
-#define IXP2000_MIN_PROD_TYPE_IXP2850 0x00000100
-#define IXP2000_MIN_PROD_TYPE_IXP2800 0x00000000
-#define IXP2000_MAJ_REV_MASK 0x000000F0
-#define IXP2000_MIN_REV_MASK 0x0000000F
-#define IXP2000_PROD_ID_MASK 0xFFFFFFFF
-
-#define IXP2000_PRODUCT_ID GLOBAL_REG(0x00)
-#define IXP2000_MISC_CONTROL GLOBAL_REG(0x04)
-#define IXP2000_MSF_CLK_CNTRL GLOBAL_REG(0x08)
-#define IXP2000_RESET0 GLOBAL_REG(0x0c)
-#define IXP2000_RESET1 GLOBAL_REG(0x10)
-#define IXP2000_CCR GLOBAL_REG(0x14)
-#define IXP2000_STRAP_OPTIONS GLOBAL_REG(0x18)
-
-#define RSTALL (1 << 16)
-#define WDT_RESET_ENABLE 0x01000000
-
-
-/*
- * MSF registers. The IXP2400 and IXP2800 have somewhat different MSF
- * units, but the registers that differ between the two don't overlap,
- * so we can have one register list for both.
- */
-#define IXP2000_MSF_REG(x) ((volatile unsigned long*)(IXP2000_MSF_VIRT_BASE + (x)))
-#define IXP2000_MSF_RX_CONTROL IXP2000_MSF_REG(0x0000)
-#define IXP2000_MSF_TX_CONTROL IXP2000_MSF_REG(0x0004)
-#define IXP2000_MSF_INTERRUPT_STATUS IXP2000_MSF_REG(0x0008)
-#define IXP2000_MSF_INTERRUPT_ENABLE IXP2000_MSF_REG(0x000c)
-#define IXP2000_MSF_CSIX_TYPE_MAP IXP2000_MSF_REG(0x0010)
-#define IXP2000_MSF_FC_EGRESS_STATUS IXP2000_MSF_REG(0x0014)
-#define IXP2000_MSF_FC_INGRESS_STATUS IXP2000_MSF_REG(0x0018)
-#define IXP2000_MSF_HWM_CONTROL IXP2000_MSF_REG(0x0024)
-#define IXP2000_MSF_FC_STATUS_OVERRIDE IXP2000_MSF_REG(0x0028)
-#define IXP2000_MSF_CLOCK_CONTROL IXP2000_MSF_REG(0x002c)
-#define IXP2000_MSF_RX_PORT_MAP IXP2000_MSF_REG(0x0040)
-#define IXP2000_MSF_RBUF_ELEMENT_DONE IXP2000_MSF_REG(0x0044)
-#define IXP2000_MSF_RX_MPHY_POLL_LIMIT IXP2000_MSF_REG(0x0048)
-#define IXP2000_MSF_RX_CALENDAR_LENGTH IXP2000_MSF_REG(0x0048)
-#define IXP2000_MSF_RX_THREAD_FREELIST_TIMEOUT_0 IXP2000_MSF_REG(0x0050)
-#define IXP2000_MSF_RX_THREAD_FREELIST_TIMEOUT_1 IXP2000_MSF_REG(0x0054)
-#define IXP2000_MSF_RX_THREAD_FREELIST_TIMEOUT_2 IXP2000_MSF_REG(0x0058)
-#define IXP2000_MSF_TX_SEQUENCE_0 IXP2000_MSF_REG(0x0060)
-#define IXP2000_MSF_TX_SEQUENCE_1 IXP2000_MSF_REG(0x0064)
-#define IXP2000_MSF_TX_SEQUENCE_2 IXP2000_MSF_REG(0x0068)
-#define IXP2000_MSF_TX_MPHY_POLL_LIMIT IXP2000_MSF_REG(0x0070)
-#define IXP2000_MSF_TX_CALENDAR_LENGTH IXP2000_MSF_REG(0x0070)
-#define IXP2000_MSF_RX_UP_CONTROL_0 IXP2000_MSF_REG(0x0080)
-#define IXP2000_MSF_RX_UP_CONTROL_1 IXP2000_MSF_REG(0x0084)
-#define IXP2000_MSF_RX_UP_CONTROL_2 IXP2000_MSF_REG(0x0088)
-#define IXP2000_MSF_RX_UP_CONTROL_3 IXP2000_MSF_REG(0x008c)
-#define IXP2000_MSF_TX_UP_CONTROL_0 IXP2000_MSF_REG(0x0090)
-#define IXP2000_MSF_TX_UP_CONTROL_1 IXP2000_MSF_REG(0x0094)
-#define IXP2000_MSF_TX_UP_CONTROL_2 IXP2000_MSF_REG(0x0098)
-#define IXP2000_MSF_TX_UP_CONTROL_3 IXP2000_MSF_REG(0x009c)
-#define IXP2000_MSF_TRAIN_DATA IXP2000_MSF_REG(0x00a0)
-#define IXP2000_MSF_TRAIN_CALENDAR IXP2000_MSF_REG(0x00a4)
-#define IXP2000_MSF_TRAIN_FLOW_CONTROL IXP2000_MSF_REG(0x00a8)
-#define IXP2000_MSF_TX_CALENDAR_0 IXP2000_MSF_REG(0x1000)
-#define IXP2000_MSF_RX_PORT_CALENDAR_STATUS IXP2000_MSF_REG(0x1400)
-
-
-#endif /* _IXP2000_H_ */
+++ /dev/null
-/*
- * arch/arm/mach-ixp2000/include/mach/memory.h
- *
- * Copyright (c) 2002 Intel Corp.
- * Copyright (c) 2003-2004 MontaVista Software, Inc.
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- */
-
-#ifndef __ASM_ARCH_MEMORY_H
-#define __ASM_ARCH_MEMORY_H
-
-#define PLAT_PHYS_OFFSET UL(0x00000000)
-
-#include <mach/ixp2000-regs.h>
-
-#define IXP2000_PCI_SDRAM_OFFSET (*IXP2000_PCI_SDRAM_BAR & 0xfffffff0)
-
-#define __phys_to_bus(x) ((x) + (IXP2000_PCI_SDRAM_OFFSET - PHYS_OFFSET))
-#define __bus_to_phys(x) ((x) - (IXP2000_PCI_SDRAM_OFFSET - PHYS_OFFSET))
-
-#define __virt_to_bus(v) __phys_to_bus(__virt_to_phys(v))
-#define __bus_to_virt(b) __phys_to_virt(__bus_to_phys(b))
-#define __pfn_to_bus(p) __phys_to_bus(__pfn_to_phys(p))
-#define __bus_to_pfn(b) __phys_to_pfn(__bus_to_phys(b))
-
-#endif
-
+++ /dev/null
-/*
- * arch/arm/mach-ixp2000/include/mach/platform.h
- *
- * Various bits of code used by platform-level code.
- *
- * Author: Deepak Saxena <dsaxena@plexity.net>
- *
- * Copyright 2004 (c) MontaVista Software, Inc.
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-
-#ifndef __ASSEMBLY__
-
-static inline unsigned long ixp2000_reg_read(volatile void *reg)
-{
- return *((volatile unsigned long *)reg);
-}
-
-static inline void ixp2000_reg_write(volatile void *reg, unsigned long val)
-{
- *((volatile unsigned long *)reg) = val;
-}
-
-/*
- * On the IXP2400, we can't use XCB=000 due to chip bugs. We use
- * XCB=101 instead, but that makes all I/O accesses bufferable. This
- * is not a problem in general, but we do have to be slightly more
- * careful because I/O writes are no longer automatically flushed out
- * of the write buffer.
- *
- * In cases where we want to make sure that a write has been flushed
- * out of the write buffer before we proceed, for example when masking
- * a device interrupt before re-enabling IRQs in CPSR, we can use this
- * function, ixp2000_reg_wrb, which performs a write, a readback, and
- * issues a dummy instruction dependent on the value of the readback
- * (mov rX, rX) to make sure that the readback has completed before we
- * continue.
- */
-static inline void ixp2000_reg_wrb(volatile void *reg, unsigned long val)
-{
- unsigned long dummy;
-
- *((volatile unsigned long *)reg) = val;
-
- dummy = *((volatile unsigned long *)reg);
- __asm__ __volatile__("mov %0, %0" : "+r" (dummy));
-}
-
-/*
- * Boards may multiplex different devices on the 2nd channel of
- * the slowport interface that each need different configuration
- * settings. For example, the IXDP2400 uses channel 2 on the interface
- * to access the CPLD, the switch fabric card, and the media card. Each
- * one needs a different mode so drivers must save/restore the mode
- * before and after each operation.
- *
- * acquire_slowport(&your_config);
- * ...
- * do slowport operations
- * ...
- * release_slowport();
- *
- * Note that while you have the slowport, you are holding a spinlock,
- * so your code should be written as if you explicitly acquired a lock.
- *
- * The configuration only affects device 2 on the slowport, so the
- * MTD map driver does not acquire/release the slowport.
- */
-struct slowport_cfg {
- unsigned long CCR; /* Clock divide */
- unsigned long WTC; /* Write Timing Control */
- unsigned long RTC; /* Read Timing Control */
- unsigned long PCR; /* Protocol Control Register */
- unsigned long ADC; /* Address/Data Width Control */
-};
-
-
-void ixp2000_acquire_slowport(struct slowport_cfg *, struct slowport_cfg *);
-void ixp2000_release_slowport(struct slowport_cfg *);
-
-/*
- * IXP2400 A0/A1 and IXP2800 A0/A1/A2 have broken slowport that requires
- * tweaking of addresses in the MTD driver.
- */
-static inline unsigned ixp2000_has_broken_slowport(void)
-{
- unsigned long id = *IXP2000_PRODUCT_ID;
- unsigned long id_prod = id & (IXP2000_MAJ_PROD_TYPE_MASK |
- IXP2000_MIN_PROD_TYPE_MASK);
- return (((id_prod ==
- /* fixed in IXP2400-B0 */
- (IXP2000_MAJ_PROD_TYPE_IXP2000 |
- IXP2000_MIN_PROD_TYPE_IXP2400)) &&
- ((id & IXP2000_MAJ_REV_MASK) == 0)) ||
- ((id_prod ==
- /* fixed in IXP2800-B0 */
- (IXP2000_MAJ_PROD_TYPE_IXP2000 |
- IXP2000_MIN_PROD_TYPE_IXP2800)) &&
- ((id & IXP2000_MAJ_REV_MASK) == 0)) ||
- ((id_prod ==
- /* fixed in IXP2850-B0 */
- (IXP2000_MAJ_PROD_TYPE_IXP2000 |
- IXP2000_MIN_PROD_TYPE_IXP2850)) &&
- ((id & IXP2000_MAJ_REV_MASK) == 0)));
-}
-
-static inline unsigned int ixp2000_has_flash(void)
-{
- return ((*IXP2000_STRAP_OPTIONS) & (CFG_BOOT_PROM));
-}
-
-static inline unsigned int ixp2000_is_pcimaster(void)
-{
- return ((*IXP2000_STRAP_OPTIONS) & (CFG_PCI_BOOT_HOST));
-}
-
-void ixp2000_map_io(void);
-void ixp2000_uart_init(void);
-void ixp2000_init_irq(void);
-void ixp2000_init_time(unsigned long);
-void ixp2000_restart(char, const char *);
-unsigned long ixp2000_gettimeoffset(void);
-
-struct pci_sys_data;
-
-u32 *ixp2000_pci_config_addr(unsigned int bus, unsigned int devfn, int where);
-void ixp2000_pci_preinit(void);
-int ixp2000_pci_setup(int, struct pci_sys_data*);
-struct pci_bus* ixp2000_pci_scan_bus(int, struct pci_sys_data*);
-int ixp2000_pci_read_config(struct pci_bus*, unsigned int, int, int, u32 *);
-int ixp2000_pci_write_config(struct pci_bus*, unsigned int, int, int, u32);
-
-/*
- * Several of the IXP2000 systems have banked flash so we need to extend the
- * flash_platform_data structure with some private pointers
- */
-struct ixp2000_flash_data {
- struct flash_platform_data *platform_data;
- int nr_banks;
- unsigned long (*bank_setup)(unsigned long);
-};
-
-struct ixp2000_i2c_pins {
- unsigned long sda_pin;
- unsigned long scl_pin;
-};
-
-
-#endif /* !__ASSEMBLY__ */
+++ /dev/null
-/*
- * arch/arm/mach-ixp2000/include/mach/timex.h
- *
- * IXP2000 architecture timex specifications
- */
-
-
-/*
- * Default clock is 50MHz APB, but platform code can override this
- */
-#define CLOCK_TICK_RATE 50000000
-
-
+++ /dev/null
-/*
- * arch/arm/mach-ixp2000/include/mach/uncompress.h
- *
- *
- * Original Author: Naeem Afzal <naeem.m.afzal@intel.com>
- * Maintainer: Deepak Saxena <dsaxena@plexity.net>
- *
- * Copyright 2002 Intel Corp.
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- *
- */
-
-#include <linux/serial_reg.h>
-
-#define UART_BASE 0xc0030000
-
-#define PHYS(x) ((volatile unsigned long *)(UART_BASE + x))
-
-#define UARTDR PHYS(0x00) /* Transmit reg dlab=0 */
-#define UARTDLL PHYS(0x00) /* Divisor Latch reg dlab=1*/
-#define UARTDLM PHYS(0x04) /* Divisor Latch reg dlab=1*/
-#define UARTIER PHYS(0x04) /* Interrupt enable reg */
-#define UARTFCR PHYS(0x08) /* FIFO control reg dlab =0*/
-#define UARTLCR PHYS(0x0c) /* Control reg */
-#define UARTSR PHYS(0x14) /* Status reg */
-
-
-static inline void putc(int c)
-{
- int j = 0x1000;
-
- while (--j && !(*UARTSR & UART_LSR_THRE))
- barrier();
-
- *UARTDR = c;
-}
-
-static inline void flush(void)
-{
-}
-
-#define arch_decomp_setup()
-#define arch_decomp_wdog()
+++ /dev/null
-/*
- * arch/arm/mach-ixp2000/ixdp2400.c
- *
- * IXDP2400 platform support
- *
- * Original Author: Naeem Afzal <naeem.m.afzal@intel.com>
- * Maintainer: Deepak Saxena <dsaxena@plexity.net>
- *
- * Copyright (C) 2002 Intel Corp.
- * Copyright (C) 2003-2004 MontaVista Software, Inc.
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- */
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/mm.h>
-#include <linux/sched.h>
-#include <linux/interrupt.h>
-#include <linux/device.h>
-#include <linux/bitops.h>
-#include <linux/pci.h>
-#include <linux/ioport.h>
-#include <linux/delay.h>
-#include <linux/io.h>
-
-#include <asm/irq.h>
-#include <asm/pgtable.h>
-#include <asm/page.h>
-#include <mach/hardware.h>
-#include <asm/mach-types.h>
-
-#include <asm/mach/pci.h>
-#include <asm/mach/map.h>
-#include <asm/mach/irq.h>
-#include <asm/mach/time.h>
-#include <asm/mach/flash.h>
-#include <asm/mach/arch.h>
-
-/*************************************************************************
- * IXDP2400 timer tick
- *************************************************************************/
-static void __init ixdp2400_timer_init(void)
-{
- int numerator, denominator;
- int denom_array[] = {2, 4, 8, 16, 1, 2, 4, 8};
-
- numerator = (*(IXDP2400_CPLD_SYS_CLK_M) & 0xFF) *2;
- denominator = denom_array[(*(IXDP2400_CPLD_SYS_CLK_N) & 0x7)];
-
- ixp2000_init_time(((3125000 * numerator) / (denominator)) / 2);
-}
-
-static struct sys_timer ixdp2400_timer = {
- .init = ixdp2400_timer_init,
- .offset = ixp2000_gettimeoffset,
-};
-
-/*************************************************************************
- * IXDP2400 PCI
- *************************************************************************/
-void __init ixdp2400_pci_preinit(void)
-{
- ixp2000_reg_write(IXP2000_PCI_ADDR_EXT, 0x00100000);
- ixp2000_pci_preinit();
- pcibios_setup("firmware");
-}
-
-int ixdp2400_pci_setup(int nr, struct pci_sys_data *sys)
-{
- sys->mem_offset = 0xe0000000;
-
- ixp2000_pci_setup(nr, sys);
-
- return 1;
-}
-
-static int __init ixdp2400_pci_map_irq(const struct pci_dev *dev, u8 slot,
- u8 pin)
-{
- if (ixdp2x00_master_npu()) {
-
- /*
- * Root bus devices. Slave NPU is only one with interrupt.
- * Everything else, we just return -1 b/c nothing else
- * on the root bus has interrupts.
- */
- if(!dev->bus->self) {
- if(dev->devfn == IXDP2X00_SLAVE_NPU_DEVFN )
- return IRQ_IXDP2400_INGRESS_NPU;
-
- return -1;
- }
-
- /*
- * Bridge behind the PMC slot.
- * NOTE: Only INTA from the PMC slot is routed. VERY BAD.
- */
- if(dev->bus->self->devfn == IXDP2X00_PMC_DEVFN &&
- dev->bus->parent->self->devfn == IXDP2X00_P2P_DEVFN &&
- !dev->bus->parent->self->bus->parent)
- return IRQ_IXDP2400_PMC;
-
- /*
- * Device behind the first bridge
- */
- if(dev->bus->self->devfn == IXDP2X00_P2P_DEVFN) {
- switch(dev->devfn) {
- case IXDP2400_MASTER_ENET_DEVFN:
- return IRQ_IXDP2400_ENET;
-
- case IXDP2400_MEDIA_DEVFN:
- return IRQ_IXDP2400_MEDIA_PCI;
-
- case IXDP2400_SWITCH_FABRIC_DEVFN:
- return IRQ_IXDP2400_SF_PCI;
-
- case IXDP2X00_PMC_DEVFN:
- return IRQ_IXDP2400_PMC;
- }
- }
-
- return -1;
- } else return IRQ_IXP2000_PCIB; /* Slave NIC interrupt */
-}
-
-
-static void ixdp2400_pci_postinit(void)
-{
- struct pci_dev *dev;
-
- if (ixdp2x00_master_npu()) {
- dev = pci_get_bus_and_slot(1, IXDP2400_SLAVE_ENET_DEVFN);
- pci_stop_and_remove_bus_device(dev);
- pci_dev_put(dev);
- } else {
- dev = pci_get_bus_and_slot(1, IXDP2400_MASTER_ENET_DEVFN);
- pci_stop_and_remove_bus_device(dev);
- pci_dev_put(dev);
-
- ixdp2x00_slave_pci_postinit();
- }
-}
-
-static struct hw_pci ixdp2400_pci __initdata = {
- .nr_controllers = 1,
- .setup = ixdp2400_pci_setup,
- .preinit = ixdp2400_pci_preinit,
- .postinit = ixdp2400_pci_postinit,
- .scan = ixp2000_pci_scan_bus,
- .map_irq = ixdp2400_pci_map_irq,
-};
-
-int __init ixdp2400_pci_init(void)
-{
- if (machine_is_ixdp2400())
- pci_common_init(&ixdp2400_pci);
-
- return 0;
-}
-
-subsys_initcall(ixdp2400_pci_init);
-
-void __init ixdp2400_init_irq(void)
-{
- ixdp2x00_init_irq(IXDP2400_CPLD_INT_STAT, IXDP2400_CPLD_INT_MASK, IXDP2400_NR_IRQS);
-}
-
-MACHINE_START(IXDP2400, "Intel IXDP2400 Development Platform")
- /* Maintainer: MontaVista Software, Inc. */
- .atag_offset = 0x100,
- .map_io = ixdp2x00_map_io,
- .init_irq = ixdp2400_init_irq,
- .timer = &ixdp2400_timer,
- .init_machine = ixdp2x00_init_machine,
- .restart = ixp2000_restart,
-MACHINE_END
-
+++ /dev/null
-/*
- * arch/arm/mach-ixp2000/ixdp2800.c
- *
- * IXDP2800 platform support
- *
- * Original Author: Jeffrey Daly <jeffrey.daly@intel.com>
- * Maintainer: Deepak Saxena <dsaxena@plexity.net>
- *
- * Copyright (C) 2002 Intel Corp.
- * Copyright (C) 2003-2004 MontaVista Software, Inc.
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- */
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/mm.h>
-#include <linux/sched.h>
-#include <linux/interrupt.h>
-#include <linux/device.h>
-#include <linux/bitops.h>
-#include <linux/pci.h>
-#include <linux/ioport.h>
-#include <linux/delay.h>
-#include <linux/io.h>
-
-#include <asm/irq.h>
-#include <asm/pgtable.h>
-#include <asm/page.h>
-#include <mach/hardware.h>
-#include <asm/mach-types.h>
-
-#include <asm/mach/pci.h>
-#include <asm/mach/map.h>
-#include <asm/mach/irq.h>
-#include <asm/mach/time.h>
-#include <asm/mach/flash.h>
-#include <asm/mach/arch.h>
-
-/*************************************************************************
- * IXDP2800 timer tick
- *************************************************************************/
-
-static void __init ixdp2800_timer_init(void)
-{
- ixp2000_init_time(50000000);
-}
-
-static struct sys_timer ixdp2800_timer = {
- .init = ixdp2800_timer_init,
- .offset = ixp2000_gettimeoffset,
-};
-
-/*************************************************************************
- * IXDP2800 PCI
- *************************************************************************/
-static void __init ixdp2800_slave_disable_pci_master(void)
-{
- *IXP2000_PCI_CMDSTAT &= ~(PCI_COMMAND_MASTER | PCI_COMMAND_MEMORY);
-}
-
-static void __init ixdp2800_master_wait_for_slave(void)
-{
- volatile u32 *addr;
-
- printk(KERN_INFO "IXDP2800: waiting for slave NPU to configure "
- "its BAR sizes\n");
-
- addr = ixp2000_pci_config_addr(0, IXDP2X00_SLAVE_NPU_DEVFN,
- PCI_BASE_ADDRESS_1);
- do {
- *addr = 0xffffffff;
- cpu_relax();
- } while (*addr != 0xfe000008);
-
- addr = ixp2000_pci_config_addr(0, IXDP2X00_SLAVE_NPU_DEVFN,
- PCI_BASE_ADDRESS_2);
- do {
- *addr = 0xffffffff;
- cpu_relax();
- } while (*addr != 0xc0000008);
-
- /*
- * Configure the slave's SDRAM BAR by hand.
- */
- *addr = 0x40000008;
-}
-
-static void __init ixdp2800_slave_wait_for_master_enable(void)
-{
- printk(KERN_INFO "IXDP2800: waiting for master NPU to enable us\n");
-
- while ((*IXP2000_PCI_CMDSTAT & PCI_COMMAND_MASTER) == 0)
- cpu_relax();
-}
-
-void __init ixdp2800_pci_preinit(void)
-{
- printk("ixdp2x00_pci_preinit called\n");
-
- *IXP2000_PCI_ADDR_EXT = 0x0001e000;
-
- if (!ixdp2x00_master_npu())
- ixdp2800_slave_disable_pci_master();
-
- *IXP2000_PCI_SRAM_BASE_ADDR_MASK = (0x2000000 - 1) & ~0x3ffff;
- *IXP2000_PCI_DRAM_BASE_ADDR_MASK = (0x40000000 - 1) & ~0xfffff;
-
- ixp2000_pci_preinit();
-
- if (ixdp2x00_master_npu()) {
- /*
- * Wait until the slave set its SRAM/SDRAM BAR sizes
- * correctly before we proceed to scan and enumerate
- * the bus.
- */
- ixdp2800_master_wait_for_slave();
-
- /*
- * We configure the SDRAM BARs by hand because they
- * are 1G and fall outside of the regular allocated
- * PCI address space.
- */
- *IXP2000_PCI_SDRAM_BAR = 0x00000008;
- } else {
- /*
- * Wait for the master to complete scanning the bus
- * and assigning resources before we proceed to scan
- * the bus ourselves. Set pci=firmware to honor the
- * master's resource assignment.
- */
- ixdp2800_slave_wait_for_master_enable();
- pcibios_setup("firmware");
- }
-}
-
-/*
- * We assign the SDRAM BARs for the two IXP2800 CPUs by hand, outside
- * of the regular PCI window, because there's only 512M of outbound PCI
- * memory window on each IXP, while we need 1G for each of the BARs.
- */
-static void __devinit ixp2800_pci_fixup(struct pci_dev *dev)
-{
- if (machine_is_ixdp2800()) {
- dev->resource[2].start = 0;
- dev->resource[2].end = 0;
- dev->resource[2].flags = 0;
- }
-}
-DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_IXP2800, ixp2800_pci_fixup);
-
-static int __init ixdp2800_pci_setup(int nr, struct pci_sys_data *sys)
-{
- sys->mem_offset = 0x00000000;
-
- ixp2000_pci_setup(nr, sys);
-
- return 1;
-}
-
-static int __init ixdp2800_pci_map_irq(const struct pci_dev *dev, u8 slot,
- u8 pin)
-{
- if (ixdp2x00_master_npu()) {
-
- /*
- * Root bus devices. Slave NPU is only one with interrupt.
- * Everything else, we just return -1 which is invalid.
- */
- if(!dev->bus->self) {
- if(dev->devfn == IXDP2X00_SLAVE_NPU_DEVFN )
- return IRQ_IXDP2800_INGRESS_NPU;
-
- return -1;
- }
-
- /*
- * Bridge behind the PMC slot.
- */
- if(dev->bus->self->devfn == IXDP2X00_PMC_DEVFN &&
- dev->bus->parent->self->devfn == IXDP2X00_P2P_DEVFN &&
- !dev->bus->parent->self->bus->parent)
- return IRQ_IXDP2800_PMC;
-
- /*
- * Device behind the first bridge
- */
- if(dev->bus->self->devfn == IXDP2X00_P2P_DEVFN) {
- switch(dev->devfn) {
- case IXDP2X00_PMC_DEVFN:
- return IRQ_IXDP2800_PMC;
-
- case IXDP2800_MASTER_ENET_DEVFN:
- return IRQ_IXDP2800_EGRESS_ENET;
-
- case IXDP2800_SWITCH_FABRIC_DEVFN:
- return IRQ_IXDP2800_FABRIC;
- }
- }
-
- return -1;
- } else return IRQ_IXP2000_PCIB; /* Slave NIC interrupt */
-}
-
-static void __init ixdp2800_master_enable_slave(void)
-{
- volatile u32 *addr;
-
- printk(KERN_INFO "IXDP2800: enabling slave NPU\n");
-
- addr = (volatile u32 *)ixp2000_pci_config_addr(0,
- IXDP2X00_SLAVE_NPU_DEVFN,
- PCI_COMMAND);
-
- *addr |= PCI_COMMAND_MASTER;
-}
-
-static void __init ixdp2800_master_wait_for_slave_bus_scan(void)
-{
- volatile u32 *addr;
-
- printk(KERN_INFO "IXDP2800: waiting for slave to finish bus scan\n");
-
- addr = (volatile u32 *)ixp2000_pci_config_addr(0,
- IXDP2X00_SLAVE_NPU_DEVFN,
- PCI_COMMAND);
- while ((*addr & PCI_COMMAND_MEMORY) == 0)
- cpu_relax();
-}
-
-static void __init ixdp2800_slave_signal_bus_scan_completion(void)
-{
- printk(KERN_INFO "IXDP2800: bus scan done, signaling master\n");
- *IXP2000_PCI_CMDSTAT |= PCI_COMMAND_MEMORY;
-}
-
-static void __init ixdp2800_pci_postinit(void)
-{
- if (!ixdp2x00_master_npu()) {
- ixdp2x00_slave_pci_postinit();
- ixdp2800_slave_signal_bus_scan_completion();
- }
-}
-
-struct __initdata hw_pci ixdp2800_pci __initdata = {
- .nr_controllers = 1,
- .setup = ixdp2800_pci_setup,
- .preinit = ixdp2800_pci_preinit,
- .postinit = ixdp2800_pci_postinit,
- .scan = ixp2000_pci_scan_bus,
- .map_irq = ixdp2800_pci_map_irq,
-};
-
-int __init ixdp2800_pci_init(void)
-{
- if (machine_is_ixdp2800()) {
- struct pci_dev *dev;
-
- pci_common_init(&ixdp2800_pci);
- if (ixdp2x00_master_npu()) {
- dev = pci_get_bus_and_slot(1, IXDP2800_SLAVE_ENET_DEVFN);
- pci_stop_and_remove_bus_device(dev);
- pci_dev_put(dev);
-
- ixdp2800_master_enable_slave();
- ixdp2800_master_wait_for_slave_bus_scan();
- } else {
- dev = pci_get_bus_and_slot(1, IXDP2800_MASTER_ENET_DEVFN);
- pci_stop_and_remove_bus_device(dev);
- pci_dev_put(dev);
- }
- }
-
- return 0;
-}
-
-subsys_initcall(ixdp2800_pci_init);
-
-void __init ixdp2800_init_irq(void)
-{
- ixdp2x00_init_irq(IXDP2800_CPLD_INT_STAT, IXDP2800_CPLD_INT_MASK, IXDP2800_NR_IRQS);
-}
-
-MACHINE_START(IXDP2800, "Intel IXDP2800 Development Platform")
- /* Maintainer: MontaVista Software, Inc. */
- .atag_offset = 0x100,
- .map_io = ixdp2x00_map_io,
- .init_irq = ixdp2800_init_irq,
- .timer = &ixdp2800_timer,
- .init_machine = ixdp2x00_init_machine,
- .restart = ixp2000_restart,
-MACHINE_END
-
+++ /dev/null
-/*
- * arch/arm/mach-ixp2000/ixdp2x00.c
- *
- * Code common to IXDP2400 and IXDP2800 platforms.
- *
- * Original Author: Naeem Afzal <naeem.m.afzal@intel.com>
- * Maintainer: Deepak Saxena <dsaxena@plexity.net>
- *
- * Copyright (C) 2002 Intel Corp.
- * Copyright (C) 2003-2004 MontaVista Software, Inc.
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- */
-#include <linux/gpio.h>
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/mm.h>
-#include <linux/sched.h>
-#include <linux/interrupt.h>
-#include <linux/platform_device.h>
-#include <linux/bitops.h>
-#include <linux/pci.h>
-#include <linux/ioport.h>
-#include <linux/delay.h>
-#include <linux/io.h>
-
-#include <asm/irq.h>
-#include <asm/pgtable.h>
-#include <asm/page.h>
-#include <mach/hardware.h>
-#include <asm/mach-types.h>
-
-#include <asm/mach/pci.h>
-#include <asm/mach/map.h>
-#include <asm/mach/irq.h>
-#include <asm/mach/time.h>
-#include <asm/mach/flash.h>
-#include <asm/mach/arch.h>
-
-#include <mach/gpio-ixp2000.h>
-
-/*************************************************************************
- * IXDP2x00 IRQ Initialization
- *************************************************************************/
-static volatile unsigned long *board_irq_mask;
-static volatile unsigned long *board_irq_stat;
-static unsigned long board_irq_count;
-
-#ifdef CONFIG_ARCH_IXDP2400
-/*
- * Slowport configuration for accessing CPLD registers on IXDP2x00
- */
-static struct slowport_cfg slowport_cpld_cfg = {
- .CCR = SLOWPORT_CCR_DIV_2,
- .WTC = 0x00000070,
- .RTC = 0x00000070,
- .PCR = SLOWPORT_MODE_FLASH,
- .ADC = SLOWPORT_ADDR_WIDTH_24 | SLOWPORT_DATA_WIDTH_8
-};
-#endif
-
-static void ixdp2x00_irq_mask(struct irq_data *d)
-{
- unsigned long dummy;
- static struct slowport_cfg old_cfg;
-
- /*
- * This is ugly in common code but really don't know
- * of a better way to handle it. :(
- */
-#ifdef CONFIG_ARCH_IXDP2400
- if (machine_is_ixdp2400())
- ixp2000_acquire_slowport(&slowport_cpld_cfg, &old_cfg);
-#endif
-
- dummy = *board_irq_mask;
- dummy |= IXP2000_BOARD_IRQ_MASK(d->irq);
- ixp2000_reg_wrb(board_irq_mask, dummy);
-
-#ifdef CONFIG_ARCH_IXDP2400
- if (machine_is_ixdp2400())
- ixp2000_release_slowport(&old_cfg);
-#endif
-}
-
-static void ixdp2x00_irq_unmask(struct irq_data *d)
-{
- unsigned long dummy;
- static struct slowport_cfg old_cfg;
-
-#ifdef CONFIG_ARCH_IXDP2400
- if (machine_is_ixdp2400())
- ixp2000_acquire_slowport(&slowport_cpld_cfg, &old_cfg);
-#endif
-
- dummy = *board_irq_mask;
- dummy &= ~IXP2000_BOARD_IRQ_MASK(d->irq);
- ixp2000_reg_wrb(board_irq_mask, dummy);
-
- if (machine_is_ixdp2400())
- ixp2000_release_slowport(&old_cfg);
-}
-
-static void ixdp2x00_irq_handler(unsigned int irq, struct irq_desc *desc)
-{
- volatile u32 ex_interrupt = 0;
- static struct slowport_cfg old_cfg;
- int i;
-
- desc->irq_data.chip->irq_mask(&desc->irq_data);
-
-#ifdef CONFIG_ARCH_IXDP2400
- if (machine_is_ixdp2400())
- ixp2000_acquire_slowport(&slowport_cpld_cfg, &old_cfg);
-#endif
- ex_interrupt = *board_irq_stat & 0xff;
- if (machine_is_ixdp2400())
- ixp2000_release_slowport(&old_cfg);
-
- if(!ex_interrupt) {
- printk(KERN_ERR "Spurious IXDP2x00 CPLD interrupt!\n");
- return;
- }
-
- for(i = 0; i < board_irq_count; i++) {
- if(ex_interrupt & (1 << i)) {
- int cpld_irq = IXP2000_BOARD_IRQ(0) + i;
- generic_handle_irq(cpld_irq);
- }
- }
-
- desc->irq_data.chip->irq_unmask(&desc->irq_data);
-}
-
-static struct irq_chip ixdp2x00_cpld_irq_chip = {
- .irq_ack = ixdp2x00_irq_mask,
- .irq_mask = ixdp2x00_irq_mask,
- .irq_unmask = ixdp2x00_irq_unmask
-};
-
-void __init ixdp2x00_init_irq(volatile unsigned long *stat_reg, volatile unsigned long *mask_reg, unsigned long nr_of_irqs)
-{
- unsigned int irq;
-
- ixp2000_init_irq();
-
- if (!ixdp2x00_master_npu())
- return;
-
- board_irq_stat = stat_reg;
- board_irq_mask = mask_reg;
- board_irq_count = nr_of_irqs;
-
- *board_irq_mask = 0xffffffff;
-
- for(irq = IXP2000_BOARD_IRQ(0); irq < IXP2000_BOARD_IRQ(board_irq_count); irq++) {
- irq_set_chip_and_handler(irq, &ixdp2x00_cpld_irq_chip,
- handle_level_irq);
- set_irq_flags(irq, IRQF_VALID);
- }
-
- /* Hook into PCI interrupt */
- irq_set_chained_handler(IRQ_IXP2000_PCIB, ixdp2x00_irq_handler);
-}
-
-/*************************************************************************
- * IXDP2x00 memory map
- *************************************************************************/
-static struct map_desc ixdp2x00_io_desc __initdata = {
- .virtual = IXDP2X00_VIRT_CPLD_BASE,
- .pfn = __phys_to_pfn(IXDP2X00_PHYS_CPLD_BASE),
- .length = IXDP2X00_CPLD_SIZE,
- .type = MT_DEVICE
-};
-
-void __init ixdp2x00_map_io(void)
-{
- ixp2000_map_io();
-
- iotable_init(&ixdp2x00_io_desc, 1);
-}
-
-/*************************************************************************
- * IXDP2x00-common PCI init
- *
- * The IXDP2[48]00 has a horrid PCI bus layout. Basically the board
- * contains two NPUs (ingress and egress) connected over PCI, both running
- * instances of the kernel. So far so good. Peers on the PCI bus running
- * Linux is a common design in telecom systems. The problem is that instead
- * of all the devices being controlled by a single host, different
- * devices are controlled by different NPUs on the same bus, leading to
- * multiple hosts on the bus. The exact bus layout looks like:
- *
- * Bus 0
- * Master NPU <-------------------+-------------------> Slave NPU
- * |
- * |
- * P2P
- * |
- *
- * Bus 1 |
- * <--+------+---------+---------+------+-->
- * | | | | |
- * | | | | |
- * ... Dev PMC Media Eth0 Eth1 ...
- *
- * The master controls all but Eth1, which is controlled by the
- * slave. What this means is that the both the master and the slave
- * have to scan the bus, but only one of them can enumerate the bus.
- * In addition, after the bus is scanned, each kernel must remove
- * the device(s) it does not control from the PCI dev list otherwise
- * a driver on each NPU will try to manage it and we will have horrible
- * conflicts. Oh..and the slave NPU needs to see the master NPU
- * for Intel's drivers to work properly. Closed source drivers...
- *
- * The way we deal with this is fairly simple but ugly:
- *
- * 1) Let master scan and enumerate the bus completely.
- * 2) Master deletes Eth1 from device list.
- * 3) Slave scans bus and then deletes all but Eth1 (Eth0 on slave)
- * from device list.
- * 4) Find HW designers and LART them.
- *
- * The boards also do not do normal PCI IRQ routing, or any sort of
- * sensical swizzling, so we just need to check where on the bus a
- * device sits and figure out to which CPLD pin the interrupt is routed.
- * See ixdp2[48]00.c files.
- *
- *************************************************************************/
-void ixdp2x00_slave_pci_postinit(void)
-{
- struct pci_dev *dev;
-
- /*
- * Remove PMC device is there is one
- */
- if((dev = pci_get_bus_and_slot(1, IXDP2X00_PMC_DEVFN))) {
- pci_stop_and_remove_bus_device(dev);
- pci_dev_put(dev);
- }
-
- dev = pci_get_bus_and_slot(0, IXDP2X00_21555_DEVFN);
- pci_stop_and_remove_bus_device(dev);
- pci_dev_put(dev);
-}
-
-/**************************************************************************
- * IXDP2x00 Machine Setup
- *************************************************************************/
-static struct flash_platform_data ixdp2x00_platform_data = {
- .map_name = "cfi_probe",
- .width = 1,
-};
-
-static struct ixp2000_flash_data ixdp2x00_flash_data = {
- .platform_data = &ixdp2x00_platform_data,
- .nr_banks = 1
-};
-
-static struct resource ixdp2x00_flash_resource = {
- .start = 0xc4000000,
- .end = 0xc4000000 + 0x00ffffff,
- .flags = IORESOURCE_MEM,
-};
-
-static struct platform_device ixdp2x00_flash = {
- .name = "IXP2000-Flash",
- .id = 0,
- .dev = {
- .platform_data = &ixdp2x00_flash_data,
- },
- .num_resources = 1,
- .resource = &ixdp2x00_flash_resource,
-};
-
-static struct ixp2000_i2c_pins ixdp2x00_i2c_gpio_pins = {
- .sda_pin = IXDP2X00_GPIO_SDA,
- .scl_pin = IXDP2X00_GPIO_SCL,
-};
-
-static struct platform_device ixdp2x00_i2c_controller = {
- .name = "IXP2000-I2C",
- .id = 0,
- .dev = {
- .platform_data = &ixdp2x00_i2c_gpio_pins,
- },
- .num_resources = 0
-};
-
-static struct platform_device *ixdp2x00_devices[] __initdata = {
- &ixdp2x00_flash,
- &ixdp2x00_i2c_controller
-};
-
-void __init ixdp2x00_init_machine(void)
-{
- gpio_line_set(IXDP2X00_GPIO_I2C_ENABLE, 1);
- gpio_line_config(IXDP2X00_GPIO_I2C_ENABLE, GPIO_OUT);
-
- platform_add_devices(ixdp2x00_devices, ARRAY_SIZE(ixdp2x00_devices));
- ixp2000_uart_init();
-}
-
+++ /dev/null
-/*
- * arch/arm/mach-ixp2000/ixdp2x01.c
- *
- * Code common to Intel IXDP2401 and IXDP2801 platforms
- *
- * Original Author: Andrzej Mialkowski <andrzej.mialkowski@intel.com>
- * Maintainer: Deepak Saxena <dsaxena@plexity.net>
- *
- * Copyright (C) 2002-2003 Intel Corp.
- * Copyright (C) 2003-2004 MontaVista Software, Inc.
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/mm.h>
-#include <linux/sched.h>
-#include <linux/interrupt.h>
-#include <linux/bitops.h>
-#include <linux/pci.h>
-#include <linux/ioport.h>
-#include <linux/delay.h>
-#include <linux/serial.h>
-#include <linux/tty.h>
-#include <linux/serial_core.h>
-#include <linux/platform_device.h>
-#include <linux/serial_8250.h>
-#include <linux/io.h>
-
-#include <asm/irq.h>
-#include <asm/pgtable.h>
-#include <asm/page.h>
-#include <mach/hardware.h>
-#include <asm/mach-types.h>
-
-#include <asm/mach/pci.h>
-#include <asm/mach/map.h>
-#include <asm/mach/irq.h>
-#include <asm/mach/time.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/flash.h>
-
-/*************************************************************************
- * IXDP2x01 IRQ Handling
- *************************************************************************/
-static void ixdp2x01_irq_mask(struct irq_data *d)
-{
- ixp2000_reg_wrb(IXDP2X01_INT_MASK_SET_REG,
- IXP2000_BOARD_IRQ_MASK(d->irq));
-}
-
-static void ixdp2x01_irq_unmask(struct irq_data *d)
-{
- ixp2000_reg_write(IXDP2X01_INT_MASK_CLR_REG,
- IXP2000_BOARD_IRQ_MASK(d->irq));
-}
-
-static u32 valid_irq_mask;
-
-static void ixdp2x01_irq_handler(unsigned int irq, struct irq_desc *desc)
-{
- u32 ex_interrupt;
- int i;
-
- desc->irq_data.chip->irq_mask(&desc->irq_data);
-
- ex_interrupt = *IXDP2X01_INT_STAT_REG & valid_irq_mask;
-
- if (!ex_interrupt) {
- printk(KERN_ERR "Spurious IXDP2X01 CPLD interrupt!\n");
- return;
- }
-
- for (i = 0; i < IXP2000_BOARD_IRQS; i++) {
- if (ex_interrupt & (1 << i)) {
- int cpld_irq = IXP2000_BOARD_IRQ(0) + i;
- generic_handle_irq(cpld_irq);
- }
- }
-
- desc->irq_data.chip->irq_unmask(&desc->irq_data);
-}
-
-static struct irq_chip ixdp2x01_irq_chip = {
- .irq_mask = ixdp2x01_irq_mask,
- .irq_ack = ixdp2x01_irq_mask,
- .irq_unmask = ixdp2x01_irq_unmask
-};
-
-/*
- * We only do anything if we are the master NPU on the board.
- * The slave NPU only has the ethernet chip going directly to
- * the PCIB interrupt input.
- */
-void __init ixdp2x01_init_irq(void)
-{
- int irq = 0;
-
- /* initialize chip specific interrupts */
- ixp2000_init_irq();
-
- if (machine_is_ixdp2401())
- valid_irq_mask = IXDP2401_VALID_IRQ_MASK;
- else
- valid_irq_mask = IXDP2801_VALID_IRQ_MASK;
-
- /* Mask all interrupts from CPLD, disable simulation */
- ixp2000_reg_write(IXDP2X01_INT_MASK_SET_REG, 0xffffffff);
- ixp2000_reg_wrb(IXDP2X01_INT_SIM_REG, 0);
-
- for (irq = NR_IXP2000_IRQS; irq < NR_IXDP2X01_IRQS; irq++) {
- if (irq & valid_irq_mask) {
- irq_set_chip_and_handler(irq, &ixdp2x01_irq_chip,
- handle_level_irq);
- set_irq_flags(irq, IRQF_VALID);
- } else {
- set_irq_flags(irq, 0);
- }
- }
-
- /* Hook into PCI interrupts */
- irq_set_chained_handler(IRQ_IXP2000_PCIB, ixdp2x01_irq_handler);
-}
-
-
-/*************************************************************************
- * IXDP2x01 memory map
- *************************************************************************/
-static struct map_desc ixdp2x01_io_desc __initdata = {
- .virtual = IXDP2X01_VIRT_CPLD_BASE,
- .pfn = __phys_to_pfn(IXDP2X01_PHYS_CPLD_BASE),
- .length = IXDP2X01_CPLD_REGION_SIZE,
- .type = MT_DEVICE
-};
-
-static void __init ixdp2x01_map_io(void)
-{
- ixp2000_map_io();
- iotable_init(&ixdp2x01_io_desc, 1);
-}
-
-
-/*************************************************************************
- * IXDP2x01 serial ports
- *************************************************************************/
-static struct plat_serial8250_port ixdp2x01_serial_port1[] = {
- {
- .mapbase = (unsigned long)IXDP2X01_UART1_PHYS_BASE,
- .membase = (char *)IXDP2X01_UART1_VIRT_BASE,
- .irq = IRQ_IXDP2X01_UART1,
- .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
- .iotype = UPIO_MEM32,
- .regshift = 2,
- .uartclk = IXDP2X01_UART_CLK,
- },
- { }
-};
-
-static struct resource ixdp2x01_uart_resource1 = {
- .start = IXDP2X01_UART1_PHYS_BASE,
- .end = IXDP2X01_UART1_PHYS_BASE + 0xffff,
- .flags = IORESOURCE_MEM,
-};
-
-static struct platform_device ixdp2x01_serial_device1 = {
- .name = "serial8250",
- .id = PLAT8250_DEV_PLATFORM1,
- .dev = {
- .platform_data = ixdp2x01_serial_port1,
- },
- .num_resources = 1,
- .resource = &ixdp2x01_uart_resource1,
-};
-
-static struct plat_serial8250_port ixdp2x01_serial_port2[] = {
- {
- .mapbase = (unsigned long)IXDP2X01_UART2_PHYS_BASE,
- .membase = (char *)IXDP2X01_UART2_VIRT_BASE,
- .irq = IRQ_IXDP2X01_UART2,
- .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
- .iotype = UPIO_MEM32,
- .regshift = 2,
- .uartclk = IXDP2X01_UART_CLK,
- },
- { }
-};
-
-static struct resource ixdp2x01_uart_resource2 = {
- .start = IXDP2X01_UART2_PHYS_BASE,
- .end = IXDP2X01_UART2_PHYS_BASE + 0xffff,
- .flags = IORESOURCE_MEM,
-};
-
-static struct platform_device ixdp2x01_serial_device2 = {
- .name = "serial8250",
- .id = PLAT8250_DEV_PLATFORM2,
- .dev = {
- .platform_data = ixdp2x01_serial_port2,
- },
- .num_resources = 1,
- .resource = &ixdp2x01_uart_resource2,
-};
-
-static void ixdp2x01_uart_init(void)
-{
- platform_device_register(&ixdp2x01_serial_device1);
- platform_device_register(&ixdp2x01_serial_device2);
-}
-
-
-/*************************************************************************
- * IXDP2x01 timer tick configuration
- *************************************************************************/
-static unsigned int ixdp2x01_clock;
-
-static int __init ixdp2x01_clock_setup(char *str)
-{
- ixdp2x01_clock = simple_strtoul(str, NULL, 10);
-
- return 1;
-}
-
-__setup("ixdp2x01_clock=", ixdp2x01_clock_setup);
-
-static void __init ixdp2x01_timer_init(void)
-{
- if (!ixdp2x01_clock)
- ixdp2x01_clock = 50000000;
-
- ixp2000_init_time(ixdp2x01_clock);
-}
-
-static struct sys_timer ixdp2x01_timer = {
- .init = ixdp2x01_timer_init,
- .offset = ixp2000_gettimeoffset,
-};
-
-/*************************************************************************
- * IXDP2x01 PCI
- *************************************************************************/
-void __init ixdp2x01_pci_preinit(void)
-{
- ixp2000_reg_write(IXP2000_PCI_ADDR_EXT, 0x00000000);
- ixp2000_pci_preinit();
- pcibios_setup("firmware");
-}
-
-#define DEVPIN(dev, pin) ((pin) | ((dev) << 3))
-
-static int __init ixdp2x01_pci_map_irq(const struct pci_dev *dev, u8 slot,
- u8 pin)
-{
- u8 bus = dev->bus->number;
- u32 devpin = DEVPIN(PCI_SLOT(dev->devfn), pin);
- struct pci_bus *tmp_bus = dev->bus;
-
- /* Primary bus, no interrupts here */
- if (bus == 0) {
- return -1;
- }
-
- /* Lookup first leaf in bus tree */
- while ((tmp_bus->parent != NULL) && (tmp_bus->parent->parent != NULL)) {
- tmp_bus = tmp_bus->parent;
- }
-
- /* Select between known bridges */
- switch (tmp_bus->self->devfn | (tmp_bus->self->bus->number << 8)) {
- /* Device is located after first MB bridge */
- case 0x0008:
- if (tmp_bus == dev->bus) {
- /* Device is located directly after first MB bridge */
- switch (devpin) {
- case DEVPIN(1, 1): /* Onboard 82546 ch 0 */
- if (machine_is_ixdp2401())
- return IRQ_IXDP2401_INTA_82546;
- return -1;
- case DEVPIN(1, 2): /* Onboard 82546 ch 1 */
- if (machine_is_ixdp2401())
- return IRQ_IXDP2401_INTB_82546;
- return -1;
- case DEVPIN(0, 1): /* PMC INTA# */
- return IRQ_IXDP2X01_SPCI_PMC_INTA;
- case DEVPIN(0, 2): /* PMC INTB# */
- return IRQ_IXDP2X01_SPCI_PMC_INTB;
- case DEVPIN(0, 3): /* PMC INTC# */
- return IRQ_IXDP2X01_SPCI_PMC_INTC;
- case DEVPIN(0, 4): /* PMC INTD# */
- return IRQ_IXDP2X01_SPCI_PMC_INTD;
- }
- }
- break;
- case 0x0010:
- if (tmp_bus == dev->bus) {
- /* Device is located directly after second MB bridge */
- /* Secondary bus of second bridge */
- switch (devpin) {
- case DEVPIN(0, 1): /* DB#0 */
- return IRQ_IXDP2X01_SPCI_DB_0;
- case DEVPIN(1, 1): /* DB#1 */
- return IRQ_IXDP2X01_SPCI_DB_1;
- }
- } else {
- /* Device is located indirectly after second MB bridge */
- /* Not supported now */
- }
- break;
- }
-
- return -1;
-}
-
-
-static int ixdp2x01_pci_setup(int nr, struct pci_sys_data *sys)
-{
- sys->mem_offset = 0xe0000000;
-
- if (machine_is_ixdp2801() || machine_is_ixdp28x5())
- sys->mem_offset -= ((*IXP2000_PCI_ADDR_EXT & 0xE000) << 16);
-
- return ixp2000_pci_setup(nr, sys);
-}
-
-struct hw_pci ixdp2x01_pci __initdata = {
- .nr_controllers = 1,
- .setup = ixdp2x01_pci_setup,
- .preinit = ixdp2x01_pci_preinit,
- .scan = ixp2000_pci_scan_bus,
- .map_irq = ixdp2x01_pci_map_irq,
-};
-
-int __init ixdp2x01_pci_init(void)
-{
- if (machine_is_ixdp2401() || machine_is_ixdp2801() ||\
- machine_is_ixdp28x5())
- pci_common_init(&ixdp2x01_pci);
-
- return 0;
-}
-
-subsys_initcall(ixdp2x01_pci_init);
-
-/*************************************************************************
- * IXDP2x01 Machine Initialization
- *************************************************************************/
-static struct flash_platform_data ixdp2x01_flash_platform_data = {
- .map_name = "cfi_probe",
- .width = 1,
-};
-
-static unsigned long ixdp2x01_flash_bank_setup(unsigned long ofs)
-{
- ixp2000_reg_wrb(IXDP2X01_CPLD_FLASH_REG,
- ((ofs >> IXDP2X01_FLASH_WINDOW_BITS) | IXDP2X01_CPLD_FLASH_INTERN));
- return (ofs & IXDP2X01_FLASH_WINDOW_MASK);
-}
-
-static struct ixp2000_flash_data ixdp2x01_flash_data = {
- .platform_data = &ixdp2x01_flash_platform_data,
- .bank_setup = ixdp2x01_flash_bank_setup
-};
-
-static struct resource ixdp2x01_flash_resource = {
- .start = 0xc4000000,
- .end = 0xc4000000 + 0x01ffffff,
- .flags = IORESOURCE_MEM,
-};
-
-static struct platform_device ixdp2x01_flash = {
- .name = "IXP2000-Flash",
- .id = 0,
- .dev = {
- .platform_data = &ixdp2x01_flash_data,
- },
- .num_resources = 1,
- .resource = &ixdp2x01_flash_resource,
-};
-
-static struct ixp2000_i2c_pins ixdp2x01_i2c_gpio_pins = {
- .sda_pin = IXDP2X01_GPIO_SDA,
- .scl_pin = IXDP2X01_GPIO_SCL,
-};
-
-static struct platform_device ixdp2x01_i2c_controller = {
- .name = "IXP2000-I2C",
- .id = 0,
- .dev = {
- .platform_data = &ixdp2x01_i2c_gpio_pins,
- },
- .num_resources = 0
-};
-
-static struct platform_device *ixdp2x01_devices[] __initdata = {
- &ixdp2x01_flash,
- &ixdp2x01_i2c_controller
-};
-
-static void __init ixdp2x01_init_machine(void)
-{
- ixp2000_reg_wrb(IXDP2X01_CPLD_FLASH_REG,
- (IXDP2X01_CPLD_FLASH_BANK_MASK | IXDP2X01_CPLD_FLASH_INTERN));
-
- ixdp2x01_flash_data.nr_banks =
- ((*IXDP2X01_CPLD_FLASH_REG & IXDP2X01_CPLD_FLASH_BANK_MASK) + 1);
-
- platform_add_devices(ixdp2x01_devices, ARRAY_SIZE(ixdp2x01_devices));
- ixp2000_uart_init();
- ixdp2x01_uart_init();
-}
-
-static void ixdp2401_restart(char mode, const char *cmd)
-{
- /*
- * Reset flash banking register so that we are pointing at
- * RedBoot bank.
- */
- ixp2000_reg_write(IXDP2X01_CPLD_FLASH_REG,
- ((0 >> IXDP2X01_FLASH_WINDOW_BITS)
- | IXDP2X01_CPLD_FLASH_INTERN));
- ixp2000_reg_wrb(IXDP2X01_CPLD_RESET_REG, 0xffffffff);
-
- ixp2000_restart(mode, cmd);
-}
-
-static void ixdp280x_restart(char mode, const char *cmd)
-{
- /*
- * On IXDP2801 we need to write this magic sequence to the CPLD
- * to cause a complete reset of the CPU and all external devices
- * and move the flash bank register back to 0.
- */
- unsigned long reset_reg = *IXDP2X01_CPLD_RESET_REG;
-
- reset_reg = 0x55AA0000 | (reset_reg & 0x0000FFFF);
- ixp2000_reg_write(IXDP2X01_CPLD_RESET_REG, reset_reg);
- ixp2000_reg_wrb(IXDP2X01_CPLD_RESET_REG, 0x80000000);
-
- ixp2000_restart(mode, cmd);
-}
-
-#ifdef CONFIG_ARCH_IXDP2401
-MACHINE_START(IXDP2401, "Intel IXDP2401 Development Platform")
- /* Maintainer: MontaVista Software, Inc. */
- .atag_offset = 0x100,
- .map_io = ixdp2x01_map_io,
- .init_irq = ixdp2x01_init_irq,
- .timer = &ixdp2x01_timer,
- .init_machine = ixdp2x01_init_machine,
- .restart = ixdp2401_restart,
-MACHINE_END
-#endif
-
-#ifdef CONFIG_ARCH_IXDP2801
-MACHINE_START(IXDP2801, "Intel IXDP2801 Development Platform")
- /* Maintainer: MontaVista Software, Inc. */
- .atag_offset = 0x100,
- .map_io = ixdp2x01_map_io,
- .init_irq = ixdp2x01_init_irq,
- .timer = &ixdp2x01_timer,
- .init_machine = ixdp2x01_init_machine,
- .restart = ixdp280x_restart,
-MACHINE_END
-
-/*
- * IXDP28x5 is basically an IXDP2801 with a different CPU but Intel
- * changed the machine ID in the bootloader
- */
-MACHINE_START(IXDP28X5, "Intel IXDP2805/2855 Development Platform")
- /* Maintainer: MontaVista Software, Inc. */
- .atag_offset = 0x100,
- .map_io = ixdp2x01_map_io,
- .init_irq = ixdp2x01_init_irq,
- .timer = &ixdp2x01_timer,
- .init_machine = ixdp2x01_init_machine,
- .restart = ixdp280x_restart,
-MACHINE_END
-#endif
-
-
+++ /dev/null
-/*
- * arch/arm/mach-ixp2000/pci.c
- *
- * PCI routines for IXDP2400/IXDP2800 boards
- *
- * Original Author: Naeem Afzal <naeem.m.afzal@intel.com>
- * Maintained by: Deepak Saxena <dsaxena@plexity.net>
- *
- * Copyright 2002 Intel Corp.
- * Copyright (C) 2003-2004 MontaVista Software, Inc.
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- */
-
-#include <linux/sched.h>
-#include <linux/kernel.h>
-#include <linux/pci.h>
-#include <linux/interrupt.h>
-#include <linux/mm.h>
-#include <linux/init.h>
-#include <linux/ioport.h>
-#include <linux/delay.h>
-#include <linux/io.h>
-
-#include <asm/irq.h>
-#include <mach/hardware.h>
-
-#include <asm/mach/pci.h>
-
-static volatile int pci_master_aborts = 0;
-
-static int clear_master_aborts(void);
-
-u32 *
-ixp2000_pci_config_addr(unsigned int bus_nr, unsigned int devfn, int where)
-{
- u32 *paddress;
-
- if (PCI_SLOT(devfn) > 7)
- return 0;
-
- /* Must be dword aligned */
- where &= ~3;
-
- /*
- * For top bus, generate type 0, else type 1
- */
- if (!bus_nr) {
- /* only bits[23:16] are used for IDSEL */
- paddress = (u32 *) (IXP2000_PCI_CFG0_VIRT_BASE
- | (1 << (PCI_SLOT(devfn) + 16))
- | (PCI_FUNC(devfn) << 8) | where);
- } else {
- paddress = (u32 *) (IXP2000_PCI_CFG1_VIRT_BASE
- | (bus_nr << 16)
- | (PCI_SLOT(devfn) << 11)
- | (PCI_FUNC(devfn) << 8) | where);
- }
-
- return paddress;
-}
-
-/*
- * Mask table, bits to mask for quantity of size 1, 2 or 4 bytes.
- * 0 and 3 are not valid indexes...
- */
-static u32 bytemask[] = {
- /*0*/ 0,
- /*1*/ 0xff,
- /*2*/ 0xffff,
- /*3*/ 0,
- /*4*/ 0xffffffff,
-};
-
-
-int ixp2000_pci_read_config(struct pci_bus *bus, unsigned int devfn, int where,
- int size, u32 *value)
-{
- u32 n;
- u32 *addr;
-
- n = where % 4;
-
- addr = ixp2000_pci_config_addr(bus->number, devfn, where);
- if (!addr)
- return PCIBIOS_DEVICE_NOT_FOUND;
-
- pci_master_aborts = 0;
- *value = (*addr >> (8*n)) & bytemask[size];
- if (pci_master_aborts) {
- pci_master_aborts = 0;
- *value = 0xffffffff;
- return PCIBIOS_DEVICE_NOT_FOUND;
- }
-
- return PCIBIOS_SUCCESSFUL;
-}
-
-/*
- * We don't do error checks by calling clear_master_aborts() b/c the
- * assumption is that the caller did a read first to make sure a device
- * exists.
- */
-int ixp2000_pci_write_config(struct pci_bus *bus, unsigned int devfn, int where,
- int size, u32 value)
-{
- u32 mask;
- u32 *addr;
- u32 temp;
-
- mask = ~(bytemask[size] << ((where % 0x4) * 8));
- addr = ixp2000_pci_config_addr(bus->number, devfn, where);
- if (!addr)
- return PCIBIOS_DEVICE_NOT_FOUND;
- temp = (u32) (value) << ((where % 0x4) * 8);
- *addr = (*addr & mask) | temp;
-
- clear_master_aborts();
-
- return PCIBIOS_SUCCESSFUL;
-}
-
-
-static struct pci_ops ixp2000_pci_ops = {
- .read = ixp2000_pci_read_config,
- .write = ixp2000_pci_write_config
-};
-
-struct pci_bus *ixp2000_pci_scan_bus(int nr, struct pci_sys_data *sysdata)
-{
- return pci_scan_root_bus(NULL, sysdata->busnr, &ixp2000_pci_ops,
- sysdata, &sysdata->resources);
-}
-
-
-int ixp2000_pci_abort_handler(unsigned long addr, unsigned int fsr, struct pt_regs *regs)
-{
-
- volatile u32 temp;
- unsigned long flags;
-
- pci_master_aborts = 1;
-
- local_irq_save(flags);
- temp = *(IXP2000_PCI_CONTROL);
- if (temp & ((1 << 8) | (1 << 5))) {
- ixp2000_reg_wrb(IXP2000_PCI_CONTROL, temp);
- }
-
- temp = *(IXP2000_PCI_CMDSTAT);
- if (temp & (1 << 29)) {
- while (temp & (1 << 29)) {
- ixp2000_reg_write(IXP2000_PCI_CMDSTAT, temp);
- temp = *(IXP2000_PCI_CMDSTAT);
- }
- }
- local_irq_restore(flags);
-
- /*
- * If it was an imprecise abort, then we need to correct the
- * return address to be _after_ the instruction.
- */
- if (fsr & (1 << 10))
- regs->ARM_pc += 4;
-
- return 0;
-}
-
-int
-clear_master_aborts(void)
-{
- volatile u32 temp;
- unsigned long flags;
-
- local_irq_save(flags);
- temp = *(IXP2000_PCI_CONTROL);
- if (temp & ((1 << 8) | (1 << 5))) {
- ixp2000_reg_wrb(IXP2000_PCI_CONTROL, temp);
- }
-
- temp = *(IXP2000_PCI_CMDSTAT);
- if (temp & (1 << 29)) {
- while (temp & (1 << 29)) {
- ixp2000_reg_write(IXP2000_PCI_CMDSTAT, temp);
- temp = *(IXP2000_PCI_CMDSTAT);
- }
- }
- local_irq_restore(flags);
-
- return 0;
-}
-
-void __init
-ixp2000_pci_preinit(void)
-{
- pci_set_flags(0);
-
- pcibios_min_io = 0;
- pcibios_min_mem = 0;
-
-#ifndef CONFIG_IXP2000_SUPPORT_BROKEN_PCI_IO
- /*
- * Configure the PCI unit to properly byteswap I/O transactions,
- * and verify that it worked.
- */
- ixp2000_reg_write(IXP2000_PCI_CONTROL,
- (*IXP2000_PCI_CONTROL | PCI_CONTROL_IEE));
-
- if ((*IXP2000_PCI_CONTROL & PCI_CONTROL_IEE) == 0)
- panic("IXP2000: PCI I/O is broken on this ixp model, and "
- "the needed workaround has not been configured in");
-#endif
-
- hook_fault_code(16+6, ixp2000_pci_abort_handler, SIGBUS, 0,
- "PCI config cycle to non-existent device");
-}
-
-
-/*
- * IXP2000 systems often have large resource requirements, so we just
- * use our own resource space.
- */
-static struct resource ixp2000_pci_mem_space = {
- .start = 0xe0000000,
- .end = 0xffffffff,
- .flags = IORESOURCE_MEM,
- .name = "PCI Mem Space"
-};
-
-static struct resource ixp2000_pci_io_space = {
- .start = 0x00010000,
- .end = 0x0001ffff,
- .flags = IORESOURCE_IO,
- .name = "PCI I/O Space"
-};
-
-int ixp2000_pci_setup(int nr, struct pci_sys_data *sys)
-{
- if (nr >= 1)
- return 0;
-
- pci_add_resource_offset(&sys->resources,
- &ixp2000_pci_io_space, sys->io_offset);
- pci_add_resource_offset(&sys->resources,
- &ixp2000_pci_mem_space, sys->mem_offset);
-
- return 1;
-}
-
+++ /dev/null
-if ARCH_IXP23XX
-
-config ARCH_SUPPORTS_BIG_ENDIAN
- bool
- default y
-
-menu "Intel IXP23xx Implementation Options"
-
-comment "IXP23xx Platforms"
-
-config MACH_ESPRESSO
- bool "Support IP Fabrics Double Espresso platform"
- help
-
-config MACH_IXDP2351
- bool "Support Intel IXDP2351 platform"
- help
-
-config MACH_ROADRUNNER
- bool "Support ADI RoadRunner platform"
- help
-
-endmenu
-
-endif
+++ /dev/null
-#
-# Makefile for the linux kernel.
-#
-obj-y := core.o pci.o
-obj-m :=
-obj-n :=
-obj- :=
-
-obj-$(CONFIG_MACH_ESPRESSO) += espresso.o
-obj-$(CONFIG_MACH_IXDP2351) += ixdp2351.o
-obj-$(CONFIG_MACH_ROADRUNNER) += roadrunner.o
+++ /dev/null
- zreladdr-y += 0x00008000
-params_phys-y := 0x00000100
+++ /dev/null
-/*
- * arch/arm/mach-ixp23xx/core.c
- *
- * Core routines for IXP23xx chips
- *
- * Author: Deepak Saxena <dsaxena@plexity.net>
- *
- * Copyright 2005 (c) MontaVista Software, Inc.
- *
- * Based on 2.4 code Copyright 2004 (c) Intel Corporation
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/spinlock.h>
-#include <linux/sched.h>
-#include <linux/interrupt.h>
-#include <linux/serial.h>
-#include <linux/tty.h>
-#include <linux/bitops.h>
-#include <linux/serial_8250.h>
-#include <linux/serial_core.h>
-#include <linux/device.h>
-#include <linux/mm.h>
-#include <linux/time.h>
-#include <linux/timex.h>
-
-#include <asm/types.h>
-#include <asm/setup.h>
-#include <asm/memory.h>
-#include <mach/hardware.h>
-#include <asm/irq.h>
-#include <asm/tlbflush.h>
-#include <asm/pgtable.h>
-#include <asm/system_misc.h>
-
-#include <asm/mach/map.h>
-#include <asm/mach/time.h>
-#include <asm/mach/irq.h>
-#include <asm/mach/arch.h>
-
-
-/*************************************************************************
- * Chip specific mappings shared by all IXP23xx systems
- *************************************************************************/
-static struct map_desc ixp23xx_io_desc[] __initdata = {
- { /* XSI-CPP CSRs */
- .virtual = IXP23XX_XSI2CPP_CSR_VIRT,
- .pfn = __phys_to_pfn(IXP23XX_XSI2CPP_CSR_PHYS),
- .length = IXP23XX_XSI2CPP_CSR_SIZE,
- .type = MT_DEVICE,
- }, { /* Expansion Bus Config */
- .virtual = IXP23XX_EXP_CFG_VIRT,
- .pfn = __phys_to_pfn(IXP23XX_EXP_CFG_PHYS),
- .length = IXP23XX_EXP_CFG_SIZE,
- .type = MT_DEVICE,
- }, { /* UART, Interrupt ctrl, GPIO, timers, NPEs, MACS,.... */
- .virtual = IXP23XX_PERIPHERAL_VIRT,
- .pfn = __phys_to_pfn(IXP23XX_PERIPHERAL_PHYS),
- .length = IXP23XX_PERIPHERAL_SIZE,
- .type = MT_DEVICE,
- }, { /* CAP CSRs */
- .virtual = IXP23XX_CAP_CSR_VIRT,
- .pfn = __phys_to_pfn(IXP23XX_CAP_CSR_PHYS),
- .length = IXP23XX_CAP_CSR_SIZE,
- .type = MT_DEVICE,
- }, { /* MSF CSRs */
- .virtual = IXP23XX_MSF_CSR_VIRT,
- .pfn = __phys_to_pfn(IXP23XX_MSF_CSR_PHYS),
- .length = IXP23XX_MSF_CSR_SIZE,
- .type = MT_DEVICE,
- }, { /* PCI I/O Space */
- .virtual = IXP23XX_PCI_IO_VIRT,
- .pfn = __phys_to_pfn(IXP23XX_PCI_IO_PHYS),
- .length = IXP23XX_PCI_IO_SIZE,
- .type = MT_DEVICE,
- }, { /* PCI Config Space */
- .virtual = IXP23XX_PCI_CFG_VIRT,
- .pfn = __phys_to_pfn(IXP23XX_PCI_CFG_PHYS),
- .length = IXP23XX_PCI_CFG_SIZE,
- .type = MT_DEVICE,
- }, { /* PCI local CFG CSRs */
- .virtual = IXP23XX_PCI_CREG_VIRT,
- .pfn = __phys_to_pfn(IXP23XX_PCI_CREG_PHYS),
- .length = IXP23XX_PCI_CREG_SIZE,
- .type = MT_DEVICE,
- }, { /* PCI MEM Space */
- .virtual = IXP23XX_PCI_MEM_VIRT,
- .pfn = __phys_to_pfn(IXP23XX_PCI_MEM_PHYS),
- .length = IXP23XX_PCI_MEM_SIZE,
- .type = MT_DEVICE,
- }
-};
-
-void __init ixp23xx_map_io(void)
-{
- iotable_init(ixp23xx_io_desc, ARRAY_SIZE(ixp23xx_io_desc));
-}
-
-
-/***************************************************************************
- * IXP23xx Interrupt Handling
- ***************************************************************************/
-enum ixp23xx_irq_type {
- IXP23XX_IRQ_LEVEL, IXP23XX_IRQ_EDGE
-};
-
-static void ixp23xx_config_irq(unsigned int, enum ixp23xx_irq_type);
-
-static int ixp23xx_irq_set_type(struct irq_data *d, unsigned int type)
-{
- int line = d->irq - IRQ_IXP23XX_GPIO6 + 6;
- u32 int_style;
- enum ixp23xx_irq_type irq_type;
- volatile u32 *int_reg;
-
- /*
- * Only GPIOs 6-15 are wired to interrupts on IXP23xx
- */
- if (line < 6 || line > 15)
- return -EINVAL;
-
- switch (type) {
- case IRQ_TYPE_EDGE_BOTH:
- int_style = IXP23XX_GPIO_STYLE_TRANSITIONAL;
- irq_type = IXP23XX_IRQ_EDGE;
- break;
- case IRQ_TYPE_EDGE_RISING:
- int_style = IXP23XX_GPIO_STYLE_RISING_EDGE;
- irq_type = IXP23XX_IRQ_EDGE;
- break;
- case IRQ_TYPE_EDGE_FALLING:
- int_style = IXP23XX_GPIO_STYLE_FALLING_EDGE;
- irq_type = IXP23XX_IRQ_EDGE;
- break;
- case IRQ_TYPE_LEVEL_HIGH:
- int_style = IXP23XX_GPIO_STYLE_ACTIVE_HIGH;
- irq_type = IXP23XX_IRQ_LEVEL;
- break;
- case IRQ_TYPE_LEVEL_LOW:
- int_style = IXP23XX_GPIO_STYLE_ACTIVE_LOW;
- irq_type = IXP23XX_IRQ_LEVEL;
- break;
- default:
- return -EINVAL;
- }
-
- ixp23xx_config_irq(d->irq, irq_type);
-
- if (line >= 8) { /* pins 8-15 */
- line -= 8;
- int_reg = (volatile u32 *)IXP23XX_GPIO_GPIT2R;
- } else { /* pins 0-7 */
- int_reg = (volatile u32 *)IXP23XX_GPIO_GPIT1R;
- }
-
- /*
- * Clear pending interrupts
- */
- *IXP23XX_GPIO_GPISR = (1 << line);
-
- /* Clear the style for the appropriate pin */
- *int_reg &= ~(IXP23XX_GPIO_STYLE_MASK <<
- (line * IXP23XX_GPIO_STYLE_SIZE));
-
- /* Set the new style */
- *int_reg |= (int_style << (line * IXP23XX_GPIO_STYLE_SIZE));
-
- return 0;
-}
-
-static void ixp23xx_irq_mask(struct irq_data *d)
-{
- volatile unsigned long *intr_reg;
- unsigned int irq = d->irq;
-
- if (irq >= 56)
- irq += 8;
-
- intr_reg = IXP23XX_INTR_EN1 + (irq / 32);
- *intr_reg &= ~(1 << (irq % 32));
-}
-
-static void ixp23xx_irq_ack(struct irq_data *d)
-{
- int line = d->irq - IRQ_IXP23XX_GPIO6 + 6;
-
- if ((line < 6) || (line > 15))
- return;
-
- *IXP23XX_GPIO_GPISR = (1 << line);
-}
-
-/*
- * Level triggered interrupts on GPIO lines can only be cleared when the
- * interrupt condition disappears.
- */
-static void ixp23xx_irq_level_unmask(struct irq_data *d)
-{
- volatile unsigned long *intr_reg;
- unsigned int irq = d->irq;
-
- ixp23xx_irq_ack(d);
-
- if (irq >= 56)
- irq += 8;
-
- intr_reg = IXP23XX_INTR_EN1 + (irq / 32);
- *intr_reg |= (1 << (irq % 32));
-}
-
-static void ixp23xx_irq_edge_unmask(struct irq_data *d)
-{
- volatile unsigned long *intr_reg;
- unsigned int irq = d->irq;
-
- if (irq >= 56)
- irq += 8;
-
- intr_reg = IXP23XX_INTR_EN1 + (irq / 32);
- *intr_reg |= (1 << (irq % 32));
-}
-
-static struct irq_chip ixp23xx_irq_level_chip = {
- .irq_ack = ixp23xx_irq_mask,
- .irq_mask = ixp23xx_irq_mask,
- .irq_unmask = ixp23xx_irq_level_unmask,
- .irq_set_type = ixp23xx_irq_set_type
-};
-
-static struct irq_chip ixp23xx_irq_edge_chip = {
- .irq_ack = ixp23xx_irq_ack,
- .irq_mask = ixp23xx_irq_mask,
- .irq_unmask = ixp23xx_irq_edge_unmask,
- .irq_set_type = ixp23xx_irq_set_type
-};
-
-static void ixp23xx_pci_irq_mask(struct irq_data *d)
-{
- unsigned int irq = d->irq;
-
- *IXP23XX_PCI_XSCALE_INT_ENABLE &= ~(1 << (IRQ_IXP23XX_INTA + 27 - irq));
-}
-
-static void ixp23xx_pci_irq_unmask(struct irq_data *d)
-{
- unsigned int irq = d->irq;
-
- *IXP23XX_PCI_XSCALE_INT_ENABLE |= (1 << (IRQ_IXP23XX_INTA + 27 - irq));
-}
-
-/*
- * TODO: Should this just be done at ASM level?
- */
-static void pci_handler(unsigned int irq, struct irq_desc *desc)
-{
- u32 pci_interrupt;
- unsigned int irqno;
-
- pci_interrupt = *IXP23XX_PCI_XSCALE_INT_STATUS;
-
- desc->irq_data.chip->irq_ack(&desc->irq_data);
-
- /* See which PCI_INTA, or PCI_INTB interrupted */
- if (pci_interrupt & (1 << 26)) {
- irqno = IRQ_IXP23XX_INTB;
- } else if (pci_interrupt & (1 << 27)) {
- irqno = IRQ_IXP23XX_INTA;
- } else {
- BUG();
- }
-
- generic_handle_irq(irqno);
-
- desc->irq_data.chip->irq_unmask(&desc->irq_data);
-}
-
-static struct irq_chip ixp23xx_pci_irq_chip = {
- .irq_ack = ixp23xx_pci_irq_mask,
- .irq_mask = ixp23xx_pci_irq_mask,
- .irq_unmask = ixp23xx_pci_irq_unmask
-};
-
-static void ixp23xx_config_irq(unsigned int irq, enum ixp23xx_irq_type type)
-{
- switch (type) {
- case IXP23XX_IRQ_LEVEL:
- irq_set_chip_and_handler(irq, &ixp23xx_irq_level_chip,
- handle_level_irq);
- break;
- case IXP23XX_IRQ_EDGE:
- irq_set_chip_and_handler(irq, &ixp23xx_irq_edge_chip,
- handle_edge_irq);
- break;
- }
- set_irq_flags(irq, IRQF_VALID);
-}
-
-void __init ixp23xx_init_irq(void)
-{
- int irq;
-
- /* Route everything to IRQ */
- *IXP23XX_INTR_SEL1 = 0x0;
- *IXP23XX_INTR_SEL2 = 0x0;
- *IXP23XX_INTR_SEL3 = 0x0;
- *IXP23XX_INTR_SEL4 = 0x0;
-
- /* Mask all sources */
- *IXP23XX_INTR_EN1 = 0x0;
- *IXP23XX_INTR_EN2 = 0x0;
- *IXP23XX_INTR_EN3 = 0x0;
- *IXP23XX_INTR_EN4 = 0x0;
-
- /*
- * Configure all IRQs for level-sensitive operation
- */
- for (irq = 0; irq <= NUM_IXP23XX_RAW_IRQS; irq++) {
- ixp23xx_config_irq(irq, IXP23XX_IRQ_LEVEL);
- }
-
- for (irq = IRQ_IXP23XX_INTA; irq <= IRQ_IXP23XX_INTB; irq++) {
- irq_set_chip_and_handler(irq, &ixp23xx_pci_irq_chip,
- handle_level_irq);
- set_irq_flags(irq, IRQF_VALID);
- }
-
- irq_set_chained_handler(IRQ_IXP23XX_PCI_INT_RPH, pci_handler);
-}
-
-
-/*************************************************************************
- * Timer-tick functions for IXP23xx
- *************************************************************************/
-#define CLOCK_TICKS_PER_USEC (CLOCK_TICK_RATE / USEC_PER_SEC)
-
-static unsigned long next_jiffy_time;
-
-static unsigned long
-ixp23xx_gettimeoffset(void)
-{
- unsigned long elapsed;
-
- elapsed = *IXP23XX_TIMER_CONT - (next_jiffy_time - LATCH);
-
- return elapsed / CLOCK_TICKS_PER_USEC;
-}
-
-static irqreturn_t
-ixp23xx_timer_interrupt(int irq, void *dev_id)
-{
- /* Clear Pending Interrupt by writing '1' to it */
- *IXP23XX_TIMER_STATUS = IXP23XX_TIMER1_INT_PEND;
- while ((signed long)(*IXP23XX_TIMER_CONT - next_jiffy_time) >= LATCH) {
- timer_tick();
- next_jiffy_time += LATCH;
- }
-
- return IRQ_HANDLED;
-}
-
-static struct irqaction ixp23xx_timer_irq = {
- .name = "IXP23xx Timer Tick",
- .handler = ixp23xx_timer_interrupt,
- .flags = IRQF_DISABLED | IRQF_TIMER | IRQF_IRQPOLL,
-};
-
-void __init ixp23xx_init_timer(void)
-{
- /* Clear Pending Interrupt by writing '1' to it */
- *IXP23XX_TIMER_STATUS = IXP23XX_TIMER1_INT_PEND;
-
- /* Setup the Timer counter value */
- *IXP23XX_TIMER1_RELOAD =
- (LATCH & ~IXP23XX_TIMER_RELOAD_MASK) | IXP23XX_TIMER_ENABLE;
-
- *IXP23XX_TIMER_CONT = 0;
- next_jiffy_time = LATCH;
-
- /* Connect the interrupt handler and enable the interrupt */
- setup_irq(IRQ_IXP23XX_TIMER1, &ixp23xx_timer_irq);
-}
-
-struct sys_timer ixp23xx_timer = {
- .init = ixp23xx_init_timer,
- .offset = ixp23xx_gettimeoffset,
-};
-
-
-/*************************************************************************
- * IXP23xx Platform Initialization
- *************************************************************************/
-static struct resource ixp23xx_uart_resources[] = {
- {
- .start = IXP23XX_UART1_PHYS,
- .end = IXP23XX_UART1_PHYS + 0x0fff,
- .flags = IORESOURCE_MEM
- }, {
- .start = IXP23XX_UART2_PHYS,
- .end = IXP23XX_UART2_PHYS + 0x0fff,
- .flags = IORESOURCE_MEM
- }
-};
-
-static struct plat_serial8250_port ixp23xx_uart_data[] = {
- {
- .mapbase = IXP23XX_UART1_PHYS,
- .membase = (char *)(IXP23XX_UART1_VIRT + 3),
- .irq = IRQ_IXP23XX_UART1,
- .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
- .iotype = UPIO_MEM,
- .regshift = 2,
- .uartclk = IXP23XX_UART_XTAL,
- }, {
- .mapbase = IXP23XX_UART2_PHYS,
- .membase = (char *)(IXP23XX_UART2_VIRT + 3),
- .irq = IRQ_IXP23XX_UART2,
- .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
- .iotype = UPIO_MEM,
- .regshift = 2,
- .uartclk = IXP23XX_UART_XTAL,
- },
- { },
-};
-
-static struct platform_device ixp23xx_uart = {
- .name = "serial8250",
- .id = 0,
- .dev.platform_data = ixp23xx_uart_data,
- .num_resources = 2,
- .resource = ixp23xx_uart_resources,
-};
-
-static struct platform_device *ixp23xx_devices[] __initdata = {
- &ixp23xx_uart,
-};
-
-void __init ixp23xx_sys_init(void)
-{
- /* by default, the idle code is disabled */
- disable_hlt();
-
- *IXP23XX_EXP_UNIT_FUSE |= 0xf;
- platform_add_devices(ixp23xx_devices, ARRAY_SIZE(ixp23xx_devices));
-}
-
-void ixp23xx_restart(char mode, const char *cmd)
-{
- /* Use on-chip reset capability */
- *IXP23XX_RESET0 |= IXP23XX_RST_ALL;
-}
+++ /dev/null
-/*
- * arch/arm/mach-ixp23xx/espresso.c
- *
- * Double Espresso-specific routines
- *
- * Author: Lennert Buytenhek <buytenh@wantstofly.org>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/spinlock.h>
-#include <linux/sched.h>
-#include <linux/interrupt.h>
-#include <linux/serial.h>
-#include <linux/tty.h>
-#include <linux/bitops.h>
-#include <linux/ioport.h>
-#include <linux/serial_8250.h>
-#include <linux/serial_core.h>
-#include <linux/device.h>
-#include <linux/mm.h>
-#include <linux/pci.h>
-#include <linux/mtd/physmap.h>
-
-#include <asm/types.h>
-#include <asm/setup.h>
-#include <asm/memory.h>
-#include <mach/hardware.h>
-#include <asm/mach-types.h>
-#include <asm/irq.h>
-#include <asm/tlbflush.h>
-#include <asm/pgtable.h>
-
-#include <asm/mach/map.h>
-#include <asm/mach/irq.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/pci.h>
-
-static int __init espresso_pci_init(void)
-{
- if (machine_is_espresso())
- ixp23xx_pci_slave_init();
-
- return 0;
-};
-subsys_initcall(espresso_pci_init);
-
-static struct physmap_flash_data espresso_flash_data = {
- .width = 2,
-};
-
-static struct resource espresso_flash_resource = {
- .start = 0x90000000,
- .end = 0x91ffffff,
- .flags = IORESOURCE_MEM,
-};
-
-static struct platform_device espresso_flash = {
- .name = "physmap-flash",
- .id = 0,
- .dev = {
- .platform_data = &espresso_flash_data,
- },
- .num_resources = 1,
- .resource = &espresso_flash_resource,
-};
-
-static void __init espresso_init(void)
-{
- platform_device_register(&espresso_flash);
-
- /*
- * Mark flash as writeable.
- */
- IXP23XX_EXP_CS0[0] |= IXP23XX_FLASH_WRITABLE;
- IXP23XX_EXP_CS0[1] |= IXP23XX_FLASH_WRITABLE;
-
- ixp23xx_sys_init();
-}
-
-MACHINE_START(ESPRESSO, "IP Fabrics Double Espresso")
- /* Maintainer: Lennert Buytenhek */
- .map_io = ixp23xx_map_io,
- .init_irq = ixp23xx_init_irq,
- .timer = &ixp23xx_timer,
- .atag_offset = 0x100,
- .init_machine = espresso_init,
- .restart = ixp23xx_restart,
-MACHINE_END
+++ /dev/null
-/*
- * arch/arm/mach-ixp23xx/include/mach/debug-macro.S
- *
- * Debugging macro include header
- *
- * Copyright (C) 1994-1999 Russell King
- * Moved from linux/arch/arm/kernel/debug.S by Ben Dooks
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-#include <mach/ixp23xx.h>
-
- .macro addruart, rp, rv, tmp
- ldr \rp, =IXP23XX_PERIPHERAL_PHYS @ physical
- ldr \rv, =IXP23XX_PERIPHERAL_VIRT @ virtual
-#ifdef __ARMEB__
- orr \rp, \rp, #0x00000003
- orr \rv, \rv, #0x00000003
-#endif
- .endm
-
-#define UART_SHIFT 2
-#include <asm/hardware/debug-8250.S>
+++ /dev/null
-/*
- * arch/arm/mach-ixp23xx/include/mach/entry-macro.S
- */
-
- .macro get_irqnr_preamble, base, tmp
- .endm
-
- .macro get_irqnr_and_base, irqnr, irqstat, base, tmp
- ldr \irqnr, =(IXP23XX_INTC_VIRT + IXP23XX_INTR_IRQ_ENC_ST_OFFSET)
- ldr \irqnr, [\irqnr] @ get interrupt number
- cmp \irqnr, #0x0 @ spurious interrupt ?
- movne \irqnr, \irqnr, lsr #2 @ skip unwanted low order bits
- subne \irqnr, \irqnr, #1 @ convert to 0 based
-
-#if 0
- cmp \irqnr, #IRQ_IXP23XX_PCI_INT_RPH
- bne 1001f
- mov \irqnr, #IRQ_IXP23XX_INTA
-
- ldr \irqnr, =0xf5000030
-
- mov \tmp, #(1<<26)
- tst \irqnr, \tmp
- movne \irqnr, #IRQ_IXP23XX_INTB
-
- mov \tmp, #(1<<27)
- tst \irqnr, \tmp
- movne \irqnr, #IRQ_IXP23XX_INTA
-1001:
-#endif
- .endm
+++ /dev/null
-/*
- * arch/arm/mach-ixp23xx/include/mach/hardware.h
- *
- * Copyright (C) 2002-2004 Intel Corporation.
- * Copyricht (C) 2005 MontaVista Software, Inc.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
- * Hardware definitions for IXP23XX based systems
- */
-
-#ifndef __ASM_ARCH_HARDWARE_H
-#define __ASM_ARCH_HARDWARE_H
-
-/* PCI IO info */
-
-#include "ixp23xx.h"
-
-/*
- * Platform helper functions
- */
-#include "platform.h"
-
-/*
- * Platform-specific headers
- */
-#include "ixdp2351.h"
-
-
-#endif
+++ /dev/null
-/*
- * arch/arm/mach-ixp23xx/include/mach/io.h
- *
- * Original Author: Naeem M Afzal <naeem.m.afzal@intel.com>
- * Maintainer: Deepak Saxena <dsaxena@plexity.net>
- *
- * Copyright (C) 2003-2005 Intel Corp.
- * Copyright (C) 2005 MontaVista Software, Inc
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#ifndef __ASM_ARCH_IO_H
-#define __ASM_ARCH_IO_H
-
-#define IO_SPACE_LIMIT 0xffffffff
-
-#define __io(p) ((void __iomem*)((p) + IXP23XX_PCI_IO_VIRT))
-
-#endif
+++ /dev/null
-/*
- * arch/arm/mach-ixp23xx/include/mach/irqs.h
- *
- * IRQ definitions for IXP23XX based systems
- *
- * Author: Naeem Afzal <naeem.m.afzal@intel.com>
- *
- * Copyright (C) 2003-2004 Intel Corporation.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#ifndef __ASM_ARCH_IRQS_H
-#define __ASM_ARCH_IRQS_H
-
-#define NR_IXP23XX_IRQS IRQ_IXP23XX_INTB+1
-#define IRQ_IXP23XX_EXTIRQS NR_IXP23XX_IRQS
-
-
-#define IRQ_IXP23XX_DBG0 0 /* Debug/Execution/MBox */
-#define IRQ_IXP23XX_DBG1 1 /* Debug/Execution/MBox */
-#define IRQ_IXP23XX_NPE_TRG 2 /* npe_trigger */
-#define IRQ_IXP23XX_TIMER1 3 /* Timer[0] */
-#define IRQ_IXP23XX_TIMER2 4 /* Timer[1] */
-#define IRQ_IXP23XX_TIMESTAMP 5 /* Timer[2], Time-stamp */
-#define IRQ_IXP23XX_WDOG 6 /* Time[3], Watchdog Timer */
-#define IRQ_IXP23XX_PCI_DBELL 7 /* PCI Doorbell */
-#define IRQ_IXP23XX_PCI_DMA1 8 /* PCI DMA Channel 1 */
-#define IRQ_IXP23XX_PCI_DMA2 9 /* PCI DMA Channel 2 */
-#define IRQ_IXP23XX_PCI_DMA3 10 /* PCI DMA Channel 3 */
-#define IRQ_IXP23XX_PCI_INT_RPH 11 /* pcxg_pci_int_rph */
-#define IRQ_IXP23XX_CPP_PMU 12 /* xpxg_pm_int_rpl */
-#define IRQ_IXP23XX_SWINT0 13 /* S/W Interrupt0 */
-#define IRQ_IXP23XX_SWINT1 14 /* S/W Interrupt1 */
-#define IRQ_IXP23XX_UART2 15 /* UART1 Interrupt */
-#define IRQ_IXP23XX_UART1 16 /* UART0 Interrupt */
-#define IRQ_IXP23XX_XSI_PMU_ROLLOVER 17 /* AHB Performance M. Unit counter rollover */
-#define IRQ_IXP23XX_XSI_AHB_PM0 18 /* intr_pm_o */
-#define IRQ_IXP23XX_XSI_AHB_ECE0 19 /* intr_ece_o */
-#define IRQ_IXP23XX_XSI_AHB_GASKET 20 /* gas_intr_o */
-#define IRQ_IXP23XX_XSI_CPP 21 /* xsi2cpp_int */
-#define IRQ_IXP23XX_CPP_XSI 22 /* cpp2xsi_int */
-#define IRQ_IXP23XX_ME_ATTN0 23 /* ME_ATTN */
-#define IRQ_IXP23XX_ME_ATTN1 24 /* ME_ATTN */
-#define IRQ_IXP23XX_ME_ATTN2 25 /* ME_ATTN */
-#define IRQ_IXP23XX_ME_ATTN3 26 /* ME_ATTN */
-#define IRQ_IXP23XX_PCI_ERR_RPH 27 /* PCXG_PCI_ERR_RPH */
-#define IRQ_IXP23XX_D0XG_ECC_CORR 28 /* D0XG_DRAM_ECC_CORR */
-#define IRQ_IXP23XX_D0XG_ECC_UNCORR 29 /* D0XG_DRAM_ECC_UNCORR */
-#define IRQ_IXP23XX_SRAM_ERR1 30 /* SRAM1_ERR */
-#define IRQ_IXP23XX_SRAM_ERR0 31 /* SRAM0_ERR */
-#define IRQ_IXP23XX_MEDIA_ERR 32 /* MEDIA_ERR */
-#define IRQ_IXP23XX_STH_DRAM_ECC_MAJ 33 /* STH_DRAM0_ECC_MAJ */
-#define IRQ_IXP23XX_GPIO6 34 /* GPIO0 interrupts */
-#define IRQ_IXP23XX_GPIO7 35 /* GPIO1 interrupts */
-#define IRQ_IXP23XX_GPIO8 36 /* GPIO2 interrupts */
-#define IRQ_IXP23XX_GPIO9 37 /* GPIO3 interrupts */
-#define IRQ_IXP23XX_GPIO10 38 /* GPIO4 interrupts */
-#define IRQ_IXP23XX_GPIO11 39 /* GPIO5 interrupts */
-#define IRQ_IXP23XX_GPIO12 40 /* GPIO6 interrupts */
-#define IRQ_IXP23XX_GPIO13 41 /* GPIO7 interrupts */
-#define IRQ_IXP23XX_GPIO14 42 /* GPIO8 interrupts */
-#define IRQ_IXP23XX_GPIO15 43 /* GPIO9 interrupts */
-#define IRQ_IXP23XX_SHAC_RING0 44 /* SHAC Ring Full */
-#define IRQ_IXP23XX_SHAC_RING1 45 /* SHAC Ring Full */
-#define IRQ_IXP23XX_SHAC_RING2 46 /* SHAC Ring Full */
-#define IRQ_IXP23XX_SHAC_RING3 47 /* SHAC Ring Full */
-#define IRQ_IXP23XX_SHAC_RING4 48 /* SHAC Ring Full */
-#define IRQ_IXP23XX_SHAC_RING5 49 /* SHAC Ring Full */
-#define IRQ_IXP23XX_SHAC_RING6 50 /* SHAC RING Full */
-#define IRQ_IXP23XX_SHAC_RING7 51 /* SHAC Ring Full */
-#define IRQ_IXP23XX_SHAC_RING8 52 /* SHAC Ring Full */
-#define IRQ_IXP23XX_SHAC_RING9 53 /* SHAC Ring Full */
-#define IRQ_IXP23XX_SHAC_RING10 54 /* SHAC Ring Full */
-#define IRQ_IXP23XX_SHAC_RING11 55 /* SHAC Ring Full */
-#define IRQ_IXP23XX_ME_THREAD_A0_ME0 56 /* ME_THREAD_A */
-#define IRQ_IXP23XX_ME_THREAD_A1_ME0 57 /* ME_THREAD_A */
-#define IRQ_IXP23XX_ME_THREAD_A2_ME0 58 /* ME_THREAD_A */
-#define IRQ_IXP23XX_ME_THREAD_A3_ME0 59 /* ME_THREAD_A */
-#define IRQ_IXP23XX_ME_THREAD_A4_ME0 60 /* ME_THREAD_A */
-#define IRQ_IXP23XX_ME_THREAD_A5_ME0 61 /* ME_THREAD_A */
-#define IRQ_IXP23XX_ME_THREAD_A6_ME0 62 /* ME_THREAD_A */
-#define IRQ_IXP23XX_ME_THREAD_A7_ME0 63 /* ME_THREAD_A */
-#define IRQ_IXP23XX_ME_THREAD_A8_ME1 64 /* ME_THREAD_A */
-#define IRQ_IXP23XX_ME_THREAD_A9_ME1 65 /* ME_THREAD_A */
-#define IRQ_IXP23XX_ME_THREAD_A10_ME1 66 /* ME_THREAD_A */
-#define IRQ_IXP23XX_ME_THREAD_A11_ME1 67 /* ME_THREAD_A */
-#define IRQ_IXP23XX_ME_THREAD_A12_ME1 68 /* ME_THREAD_A */
-#define IRQ_IXP23XX_ME_THREAD_A13_ME1 69 /* ME_THREAD_A */
-#define IRQ_IXP23XX_ME_THREAD_A14_ME1 70 /* ME_THREAD_A */
-#define IRQ_IXP23XX_ME_THREAD_A15_ME1 71 /* ME_THREAD_A */
-#define IRQ_IXP23XX_ME_THREAD_A16_ME2 72 /* ME_THREAD_A */
-#define IRQ_IXP23XX_ME_THREAD_A17_ME2 73 /* ME_THREAD_A */
-#define IRQ_IXP23XX_ME_THREAD_A18_ME2 74 /* ME_THREAD_A */
-#define IRQ_IXP23XX_ME_THREAD_A19_ME2 75 /* ME_THREAD_A */
-#define IRQ_IXP23XX_ME_THREAD_A20_ME2 76 /* ME_THREAD_A */
-#define IRQ_IXP23XX_ME_THREAD_A21_ME2 77 /* ME_THREAD_A */
-#define IRQ_IXP23XX_ME_THREAD_A22_ME2 78 /* ME_THREAD_A */
-#define IRQ_IXP23XX_ME_THREAD_A23_ME2 79 /* ME_THREAD_A */
-#define IRQ_IXP23XX_ME_THREAD_A24_ME3 80 /* ME_THREAD_A */
-#define IRQ_IXP23XX_ME_THREAD_A25_ME3 81 /* ME_THREAD_A */
-#define IRQ_IXP23XX_ME_THREAD_A26_ME3 82 /* ME_THREAD_A */
-#define IRQ_IXP23XX_ME_THREAD_A27_ME3 83 /* ME_THREAD_A */
-#define IRQ_IXP23XX_ME_THREAD_A28_ME3 84 /* ME_THREAD_A */
-#define IRQ_IXP23XX_ME_THREAD_A29_ME3 85 /* ME_THREAD_A */
-#define IRQ_IXP23XX_ME_THREAD_A30_ME3 86 /* ME_THREAD_A */
-#define IRQ_IXP23XX_ME_THREAD_A31_ME3 87 /* ME_THREAD_A */
-#define IRQ_IXP23XX_ME_THREAD_B0_ME0 88 /* ME_THREAD_B */
-#define IRQ_IXP23XX_ME_THREAD_B1_ME0 89 /* ME_THREAD_B */
-#define IRQ_IXP23XX_ME_THREAD_B2_ME0 90 /* ME_THREAD_B */
-#define IRQ_IXP23XX_ME_THREAD_B3_ME0 91 /* ME_THREAD_B */
-#define IRQ_IXP23XX_ME_THREAD_B4_ME0 92 /* ME_THREAD_B */
-#define IRQ_IXP23XX_ME_THREAD_B5_ME0 93 /* ME_THREAD_B */
-#define IRQ_IXP23XX_ME_THREAD_B6_ME0 94 /* ME_THREAD_B */
-#define IRQ_IXP23XX_ME_THREAD_B7_ME0 95 /* ME_THREAD_B */
-#define IRQ_IXP23XX_ME_THREAD_B8_ME1 96 /* ME_THREAD_B */
-#define IRQ_IXP23XX_ME_THREAD_B9_ME1 97 /* ME_THREAD_B */
-#define IRQ_IXP23XX_ME_THREAD_B10_ME1 98 /* ME_THREAD_B */
-#define IRQ_IXP23XX_ME_THREAD_B11_ME1 99 /* ME_THREAD_B */
-#define IRQ_IXP23XX_ME_THREAD_B12_ME1 100 /* ME_THREAD_B */
-#define IRQ_IXP23XX_ME_THREAD_B13_ME1 101 /* ME_THREAD_B */
-#define IRQ_IXP23XX_ME_THREAD_B14_ME1 102 /* ME_THREAD_B */
-#define IRQ_IXP23XX_ME_THREAD_B15_ME1 103 /* ME_THREAD_B */
-#define IRQ_IXP23XX_ME_THREAD_B16_ME2 104 /* ME_THREAD_B */
-#define IRQ_IXP23XX_ME_THREAD_B17_ME2 105 /* ME_THREAD_B */
-#define IRQ_IXP23XX_ME_THREAD_B18_ME2 106 /* ME_THREAD_B */
-#define IRQ_IXP23XX_ME_THREAD_B19_ME2 107 /* ME_THREAD_B */
-#define IRQ_IXP23XX_ME_THREAD_B20_ME2 108 /* ME_THREAD_B */
-#define IRQ_IXP23XX_ME_THREAD_B21_ME2 109 /* ME_THREAD_B */
-#define IRQ_IXP23XX_ME_THREAD_B22_ME2 110 /* ME_THREAD_B */
-#define IRQ_IXP23XX_ME_THREAD_B23_ME2 111 /* ME_THREAD_B */
-#define IRQ_IXP23XX_ME_THREAD_B24_ME3 112 /* ME_THREAD_B */
-#define IRQ_IXP23XX_ME_THREAD_B25_ME3 113 /* ME_THREAD_B */
-#define IRQ_IXP23XX_ME_THREAD_B26_ME3 114 /* ME_THREAD_B */
-#define IRQ_IXP23XX_ME_THREAD_B27_ME3 115 /* ME_THREAD_B */
-#define IRQ_IXP23XX_ME_THREAD_B28_ME3 116 /* ME_THREAD_B */
-#define IRQ_IXP23XX_ME_THREAD_B29_ME3 117 /* ME_THREAD_B */
-#define IRQ_IXP23XX_ME_THREAD_B30_ME3 118 /* ME_THREAD_B */
-#define IRQ_IXP23XX_ME_THREAD_B31_ME3 119 /* ME_THREAD_B */
-
-#define NUM_IXP23XX_RAW_IRQS 120
-
-#define IRQ_IXP23XX_INTA 120 /* Indirect pcxg_pci_int_rph */
-#define IRQ_IXP23XX_INTB 121 /* Indirect pcxg_pci_int_rph */
-
-#define NR_IXP23XX_IRQ (IRQ_IXP23XX_INTB + 1)
-
-/*
- * We default to 32 per-board IRQs. Increase this number if you need
- * more, but keep it realistic.
- */
-#define NR_IXP23XX_MACH_IRQS 32
-
-#define NR_IRQS (NR_IXP23XX_IRQS + NR_IXP23XX_MACH_IRQS)
-
-#define IXP23XX_MACH_IRQ(irq) (NR_IXP23XX_IRQ + (irq))
-
-
-/*
- * IXDP2351-specific interrupts
- */
-
-/*
- * External PCI interrupts signaled through INTB
- *
- */
-#define IXDP2351_INTB_IRQ_BASE 0
-#define IRQ_IXDP2351_INTA_82546 IXP23XX_MACH_IRQ(0)
-#define IRQ_IXDP2351_INTB_82546 IXP23XX_MACH_IRQ(1)
-#define IRQ_IXDP2351_SPCI_DB_0 IXP23XX_MACH_IRQ(2)
-#define IRQ_IXDP2351_SPCI_DB_1 IXP23XX_MACH_IRQ(3)
-#define IRQ_IXDP2351_SPCI_PMC_INTA IXP23XX_MACH_IRQ(4)
-#define IRQ_IXDP2351_SPCI_PMC_INTB IXP23XX_MACH_IRQ(5)
-#define IRQ_IXDP2351_SPCI_PMC_INTC IXP23XX_MACH_IRQ(6)
-#define IRQ_IXDP2351_SPCI_PMC_INTD IXP23XX_MACH_IRQ(7)
-#define IRQ_IXDP2351_SPCI_FIC IXP23XX_MACH_IRQ(8)
-
-#define IXDP2351_INTB_IRQ_BIT(irq) (irq - IXP23XX_MACH_IRQ(0))
-#define IXDP2351_INTB_IRQ_MASK(irq) (1 << IXDP2351_INTB_IRQ_BIT(irq))
-#define IXDP2351_INTB_IRQ_VALID 0x01FF
-#define IXDP2351_INTB_IRQ_NUM 16
-
-/*
- * Other external interrupts signaled through INTA
- */
-#define IXDP2351_INTA_IRQ_BASE 16
-#define IRQ_IXDP2351_IPMI_FROM IXP23XX_MACH_IRQ(16)
-#define IRQ_IXDP2351_125US IXP23XX_MACH_IRQ(17)
-#define IRQ_IXDP2351_DB_0_ADD IXP23XX_MACH_IRQ(18)
-#define IRQ_IXDP2351_DB_1_ADD IXP23XX_MACH_IRQ(19)
-#define IRQ_IXDP2351_DEBUG1 IXP23XX_MACH_IRQ(20)
-#define IRQ_IXDP2351_ADD_UART IXP23XX_MACH_IRQ(21)
-#define IRQ_IXDP2351_FIC_ADD IXP23XX_MACH_IRQ(24)
-#define IRQ_IXDP2351_CS8900 IXP23XX_MACH_IRQ(25)
-#define IRQ_IXDP2351_BBSRAM IXP23XX_MACH_IRQ(26)
-#define IRQ_IXDP2351_CONFIG_MEDIA IXP23XX_MACH_IRQ(27)
-#define IRQ_IXDP2351_CLOCK_REF IXP23XX_MACH_IRQ(28)
-#define IRQ_IXDP2351_A10_NP IXP23XX_MACH_IRQ(29)
-#define IRQ_IXDP2351_A11_NP IXP23XX_MACH_IRQ(30)
-#define IRQ_IXDP2351_DEBUG_NP IXP23XX_MACH_IRQ(31)
-
-#define IXDP2351_INTA_IRQ_BIT(irq) (irq - IXP23XX_MACH_IRQ(16))
-#define IXDP2351_INTA_IRQ_MASK(irq) (1 << IXDP2351_INTA_IRQ_BIT(irq))
-#define IXDP2351_INTA_IRQ_VALID 0xFF3F
-#define IXDP2351_INTA_IRQ_NUM 16
-
-
-/*
- * ADI RoadRunner IRQs
- */
-#define IRQ_ROADRUNNER_PCI_INTA IRQ_IXP23XX_INTA
-#define IRQ_ROADRUNNER_PCI_INTB IRQ_IXP23XX_INTB
-#define IRQ_ROADRUNNER_PCI_INTC IRQ_IXP23XX_GPIO11
-#define IRQ_ROADRUNNER_PCI_INTD IRQ_IXP23XX_GPIO12
-
-/*
- * Put new board definitions here
- */
-
-
-#endif
+++ /dev/null
-/*
- * arch/arm/mach-ixp23xx/include/mach/ixdp2351.h
- *
- * Register and other defines for IXDP2351
- *
- * Copyright (c) 2002-2004 Intel Corp.
- * Copytight (c) 2005 MontaVista Software, Inc.
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- */
-
-#ifndef __ASM_ARCH_IXDP2351_H
-#define __ASM_ARCH_IXDP2351_H
-
-/*
- * NP module memory map
- */
-#define IXDP2351_NP_PHYS_BASE (IXP23XX_EXP_BUS_CS4_BASE)
-#define IXDP2351_NP_PHYS_SIZE 0x00100000
-#define IXDP2351_NP_VIRT_BASE 0xeff00000
-
-#define IXDP2351_VIRT_CS8900_BASE (IXDP2351_NP_VIRT_BASE)
-#define IXDP2351_VIRT_CS8900_END (IXDP2351_VIRT_CS8900_BASE + 16)
-
-#define IXDP2351_VIRT_NP_CPLD_BASE (IXP23XX_EXP_BUS_CS4_BASE_VIRT + 0x00010000)
-
-#define IXDP2351_NP_CPLD_REG(reg) ((volatile u16 *)(IXDP2351_VIRT_NP_CPLD_BASE + reg))
-
-#define IXDP2351_NP_CPLD_RESET1_REG IXDP2351_NP_CPLD_REG(0x00)
-#define IXDP2351_NP_CPLD_LED_REG IXDP2351_NP_CPLD_REG(0x02)
-#define IXDP2351_NP_CPLD_VERSION_REG IXDP2351_NP_CPLD_REG(0x04)
-
-/*
- * Base board module memory map
- */
-
-#define IXDP2351_BB_BASE_PHYS (IXP23XX_EXP_BUS_CS5_BASE)
-#define IXDP2351_BB_SIZE 0x01000000
-#define IXDP2351_BB_BASE_VIRT (0xee000000)
-
-#define IXDP2351_BB_AREA_BASE(offset) (IXDP2351_BB_BASE_VIRT + offset)
-
-#define IXDP2351_VIRT_NVRAM_BASE IXDP2351_BB_AREA_BASE(0x0)
-#define IXDP2351_NVRAM_SIZE (0x20000)
-
-#define IXDP2351_VIRT_MB_IXF1104_BASE IXDP2351_BB_AREA_BASE(0x00020000)
-#define IXDP2351_VIRT_ADD_UART_BASE IXDP2351_BB_AREA_BASE(0x000240C0)
-#define IXDP2351_VIRT_FIC_BASE IXDP2351_BB_AREA_BASE(0x00200000)
-#define IXDP2351_VIRT_DB0_BASE IXDP2351_BB_AREA_BASE(0x00400000)
-#define IXDP2351_VIRT_DB1_BASE IXDP2351_BB_AREA_BASE(0x00600000)
-#define IXDP2351_VIRT_CPLD_BASE IXDP2351_BB_AREA_BASE(0x00024000)
-
-/*
- * On board CPLD registers
- */
-#define IXDP2351_CPLD_BB_REG(reg) ((volatile u16 *)(IXDP2351_VIRT_CPLD_BASE + reg))
-
-#define IXDP2351_CPLD_RESET0_REG IXDP2351_CPLD_BB_REG(0x00)
-#define IXDP2351_CPLD_RESET1_REG IXDP2351_CPLD_BB_REG(0x04)
-
-#define IXDP2351_CPLD_RESET1_MAGIC 0x55AA
-#define IXDP2351_CPLD_RESET1_ENABLE 0x8000
-
-#define IXDP2351_CPLD_FPGA_CONFIG_REG IXDP2351_CPLD_BB_REG(0x08)
-#define IXDP2351_CPLD_INTB_MASK_SET_REG IXDP2351_CPLD_BB_REG(0x10)
-#define IXDP2351_CPLD_INTA_MASK_SET_REG IXDP2351_CPLD_BB_REG(0x14)
-#define IXDP2351_CPLD_INTB_STAT_REG IXDP2351_CPLD_BB_REG(0x18)
-#define IXDP2351_CPLD_INTA_STAT_REG IXDP2351_CPLD_BB_REG(0x1C)
-#define IXDP2351_CPLD_INTB_RAW_REG IXDP2351_CPLD_BB_REG(0x20) /* read */
-#define IXDP2351_CPLD_INTA_RAW_REG IXDP2351_CPLD_BB_REG(0x24) /* read */
-#define IXDP2351_CPLD_INTB_MASK_CLR_REG IXDP2351_CPLD_INTB_RAW_REG /* write */
-#define IXDP2351_CPLD_INTA_MASK_CLR_REG IXDP2351_CPLD_INTA_RAW_REG /* write */
-#define IXDP2351_CPLD_INTB_SIM_REG IXDP2351_CPLD_BB_REG(0x28)
-#define IXDP2351_CPLD_INTA_SIM_REG IXDP2351_CPLD_BB_REG(0x2C)
- /* Interrupt bits are defined in irqs.h */
-#define IXDP2351_CPLD_BB_GBE0_REG IXDP2351_CPLD_BB_REG(0x30)
-#define IXDP2351_CPLD_BB_GBE1_REG IXDP2351_CPLD_BB_REG(0x34)
-
-/* #define IXDP2351_CPLD_BB_MISC_REG IXDP2351_CPLD_REG(0x1C) */
-/* #define IXDP2351_CPLD_BB_MISC_REV_MASK 0xFF */
-/* #define IXDP2351_CPLD_BB_GDXCS0_REG IXDP2351_CPLD_REG(0x24) */
-/* #define IXDP2351_CPLD_BB_GDXCS1_REG IXDP2351_CPLD_REG(0x28) */
-/* #define IXDP2351_CPLD_BB_CLOCK_REG IXDP2351_CPLD_REG(0x04) */
-
-
-#endif
+++ /dev/null
-/*
- * arch/arm/mach-ixp23xx/include/mach/ixp23xx.h
- *
- * Register definitions for IXP23XX
- *
- * Copyright (C) 2003-2005 Intel Corporation.
- * Copyright (C) 2005 MontaVista Software, Inc.
- *
- * Maintainer: Deepak Saxena <dsaxena@plexity.net>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#ifndef __ASM_ARCH_IXP23XX_H
-#define __ASM_ARCH_IXP23XX_H
-
-/*
- * IXP2300 linux memory map:
- *
- * virt phys size
- * fffd0000 a0000000 64K XSI2CPP_CSR
- * fffc0000 c4000000 4K EXP_CFG
- * fff00000 c8000000 64K PERIPHERAL
- * fe000000 1c0000000 16M CAP_CSR
- * fd000000 1c8000000 16M MSF_CSR
- * fb000000 16M ---
- * fa000000 1d8000000 32M PCI_IO
- * f8000000 1da000000 32M PCI_CFG
- * f6000000 1de000000 32M PCI_CREG
- * f4000000 32M ---
- * f0000000 1e0000000 64M PCI_MEM
- * e[c-f]000000 per-platform mappings
- */
-
-
-/****************************************************************************
- * Static mappings.
- ****************************************************************************/
-#define IXP23XX_XSI2CPP_CSR_PHYS 0xa0000000
-#define IXP23XX_XSI2CPP_CSR_VIRT 0xfffd0000
-#define IXP23XX_XSI2CPP_CSR_SIZE 0x00010000
-
-#define IXP23XX_EXP_CFG_PHYS 0xc4000000
-#define IXP23XX_EXP_CFG_VIRT 0xfffc0000
-#define IXP23XX_EXP_CFG_SIZE 0x00001000
-
-#define IXP23XX_PERIPHERAL_PHYS 0xc8000000
-#define IXP23XX_PERIPHERAL_VIRT 0xfff00000
-#define IXP23XX_PERIPHERAL_SIZE 0x00010000
-
-#define IXP23XX_CAP_CSR_PHYS 0x1c0000000ULL
-#define IXP23XX_CAP_CSR_VIRT 0xfe000000
-#define IXP23XX_CAP_CSR_SIZE 0x01000000
-
-#define IXP23XX_MSF_CSR_PHYS 0x1c8000000ULL
-#define IXP23XX_MSF_CSR_VIRT 0xfd000000
-#define IXP23XX_MSF_CSR_SIZE 0x01000000
-
-#define IXP23XX_PCI_IO_PHYS 0x1d8000000ULL
-#define IXP23XX_PCI_IO_VIRT 0xfa000000
-#define IXP23XX_PCI_IO_SIZE 0x02000000
-
-#define IXP23XX_PCI_CFG_PHYS 0x1da000000ULL
-#define IXP23XX_PCI_CFG_VIRT 0xf8000000
-#define IXP23XX_PCI_CFG_SIZE 0x02000000
-#define IXP23XX_PCI_CFG0_VIRT IXP23XX_PCI_CFG_VIRT
-#define IXP23XX_PCI_CFG1_VIRT (IXP23XX_PCI_CFG_VIRT + 0x01000000)
-
-#define IXP23XX_PCI_CREG_PHYS 0x1de000000ULL
-#define IXP23XX_PCI_CREG_VIRT 0xf6000000
-#define IXP23XX_PCI_CREG_SIZE 0x02000000
-#define IXP23XX_PCI_CSR_VIRT (IXP23XX_PCI_CREG_VIRT + 0x01000000)
-
-#define IXP23XX_PCI_MEM_START 0xe0000000
-#define IXP23XX_PCI_MEM_PHYS 0x1e0000000ULL
-#define IXP23XX_PCI_MEM_VIRT 0xf0000000
-#define IXP23XX_PCI_MEM_SIZE 0x04000000
-
-
-/****************************************************************************
- * XSI2CPP CSRs.
- ****************************************************************************/
-#define IXP23XX_XSI2CPP_REG(x) ((volatile unsigned long *)(IXP23XX_XSI2CPP_CSR_VIRT + (x)))
-#define IXP23XX_CPP2XSI_CURR_XFER_REG3 IXP23XX_XSI2CPP_REG(0xf8)
-#define IXP23XX_CPP2XSI_ADDR_31 (1 << 19)
-#define IXP23XX_CPP2XSI_PSH_OFF (1 << 20)
-#define IXP23XX_CPP2XSI_COH_OFF (1 << 21)
-
-
-/****************************************************************************
- * Expansion Bus Config.
- ****************************************************************************/
-#define IXP23XX_EXP_CFG_REG(x) ((volatile unsigned long *)(IXP23XX_EXP_CFG_VIRT + (x)))
-#define IXP23XX_EXP_CS0 IXP23XX_EXP_CFG_REG(0x00)
-#define IXP23XX_EXP_CS1 IXP23XX_EXP_CFG_REG(0x04)
-#define IXP23XX_EXP_CS2 IXP23XX_EXP_CFG_REG(0x08)
-#define IXP23XX_EXP_CS3 IXP23XX_EXP_CFG_REG(0x0c)
-#define IXP23XX_EXP_CS4 IXP23XX_EXP_CFG_REG(0x10)
-#define IXP23XX_EXP_CS5 IXP23XX_EXP_CFG_REG(0x14)
-#define IXP23XX_EXP_CS6 IXP23XX_EXP_CFG_REG(0x18)
-#define IXP23XX_EXP_CS7 IXP23XX_EXP_CFG_REG(0x1c)
-#define IXP23XX_FLASH_WRITABLE (0x2)
-#define IXP23XX_FLASH_BUS8 (0x1)
-
-#define IXP23XX_EXP_CFG0 IXP23XX_EXP_CFG_REG(0x20)
-#define IXP23XX_EXP_CFG1 IXP23XX_EXP_CFG_REG(0x24)
-#define IXP23XX_EXP_CFG0_MEM_MAP (1 << 31)
-#define IXP23XX_EXP_CFG0_XSCALE_SPEED_SEL (3 << 22)
-#define IXP23XX_EXP_CFG0_XSCALE_SPEED_EN (1 << 21)
-#define IXP23XX_EXP_CFG0_CPP_SPEED_SEL (3 << 19)
-#define IXP23XX_EXP_CFG0_CPP_SPEED_EN (1 << 18)
-#define IXP23XX_EXP_CFG0_PCI_SWIN (3 << 16)
-#define IXP23XX_EXP_CFG0_PCI_DWIN (3 << 14)
-#define IXP23XX_EXP_CFG0_PCI33_MODE (1 << 13)
-#define IXP23XX_EXP_CFG0_QDR_SPEED_SEL (1 << 12)
-#define IXP23XX_EXP_CFG0_CPP_DIV_SEL (1 << 5)
-#define IXP23XX_EXP_CFG0_XSI_NOT_PRES (1 << 4)
-#define IXP23XX_EXP_CFG0_PROM_BOOT (1 << 3)
-#define IXP23XX_EXP_CFG0_PCI_ARB (1 << 2)
-#define IXP23XX_EXP_CFG0_PCI_HOST (1 << 1)
-#define IXP23XX_EXP_CFG0_FLASH_WIDTH (1 << 0)
-
-#define IXP23XX_EXP_UNIT_FUSE IXP23XX_EXP_CFG_REG(0x28)
-#define IXP23XX_EXP_MSF_MUX IXP23XX_EXP_CFG_REG(0x30)
-#define IXP23XX_EXP_CFG_FUSE IXP23XX_EXP_CFG_REG(0x34)
-
-#define IXP23XX_EXP_BUS_PHYS 0x90000000
-#define IXP23XX_EXP_BUS_WINDOW_SIZE 0x01000000
-
-#define IXP23XX_EXP_BUS_CS0_BASE (IXP23XX_EXP_BUS_PHYS + 0x00000000)
-#define IXP23XX_EXP_BUS_CS1_BASE (IXP23XX_EXP_BUS_PHYS + 0x01000000)
-#define IXP23XX_EXP_BUS_CS2_BASE (IXP23XX_EXP_BUS_PHYS + 0x02000000)
-#define IXP23XX_EXP_BUS_CS3_BASE (IXP23XX_EXP_BUS_PHYS + 0x03000000)
-#define IXP23XX_EXP_BUS_CS4_BASE (IXP23XX_EXP_BUS_PHYS + 0x04000000)
-#define IXP23XX_EXP_BUS_CS5_BASE (IXP23XX_EXP_BUS_PHYS + 0x05000000)
-#define IXP23XX_EXP_BUS_CS6_BASE (IXP23XX_EXP_BUS_PHYS + 0x06000000)
-#define IXP23XX_EXP_BUS_CS7_BASE (IXP23XX_EXP_BUS_PHYS + 0x07000000)
-
-
-/****************************************************************************
- * Peripherals.
- ****************************************************************************/
-#define IXP23XX_UART1_VIRT (IXP23XX_PERIPHERAL_VIRT + 0x0000)
-#define IXP23XX_UART2_VIRT (IXP23XX_PERIPHERAL_VIRT + 0x1000)
-#define IXP23XX_PMU_VIRT (IXP23XX_PERIPHERAL_VIRT + 0x2000)
-#define IXP23XX_INTC_VIRT (IXP23XX_PERIPHERAL_VIRT + 0x3000)
-#define IXP23XX_GPIO_VIRT (IXP23XX_PERIPHERAL_VIRT + 0x4000)
-#define IXP23XX_TIMER_VIRT (IXP23XX_PERIPHERAL_VIRT + 0x5000)
-#define IXP23XX_NPE0_VIRT (IXP23XX_PERIPHERAL_VIRT + 0x6000)
-#define IXP23XX_DSR_VIRT (IXP23XX_PERIPHERAL_VIRT + 0x7000)
-#define IXP23XX_NPE1_VIRT (IXP23XX_PERIPHERAL_VIRT + 0x8000)
-#define IXP23XX_ETH0_VIRT (IXP23XX_PERIPHERAL_VIRT + 0x9000)
-#define IXP23XX_ETH1_VIRT (IXP23XX_PERIPHERAL_VIRT + 0xA000)
-#define IXP23XX_GIG0_VIRT (IXP23XX_PERIPHERAL_VIRT + 0xB000)
-#define IXP23XX_GIG1_VIRT (IXP23XX_PERIPHERAL_VIRT + 0xC000)
-#define IXP23XX_DDRS_VIRT (IXP23XX_PERIPHERAL_VIRT + 0xD000)
-
-#define IXP23XX_UART1_PHYS (IXP23XX_PERIPHERAL_PHYS + 0x0000)
-#define IXP23XX_UART2_PHYS (IXP23XX_PERIPHERAL_PHYS + 0x1000)
-#define IXP23XX_PMU_PHYS (IXP23XX_PERIPHERAL_PHYS + 0x2000)
-#define IXP23XX_INTC_PHYS (IXP23XX_PERIPHERAL_PHYS + 0x3000)
-#define IXP23XX_GPIO_PHYS (IXP23XX_PERIPHERAL_PHYS + 0x4000)
-#define IXP23XX_TIMER_PHYS (IXP23XX_PERIPHERAL_PHYS + 0x5000)
-#define IXP23XX_NPE0_PHYS (IXP23XX_PERIPHERAL_PHYS + 0x6000)
-#define IXP23XX_DSR_PHYS (IXP23XX_PERIPHERAL_PHYS + 0x7000)
-#define IXP23XX_NPE1_PHYS (IXP23XX_PERIPHERAL_PHYS + 0x8000)
-#define IXP23XX_ETH0_PHYS (IXP23XX_PERIPHERAL_PHYS + 0x9000)
-#define IXP23XX_ETH1_PHYS (IXP23XX_PERIPHERAL_PHYS + 0xA000)
-#define IXP23XX_GIG0_PHYS (IXP23XX_PERIPHERAL_PHYS + 0xB000)
-#define IXP23XX_GIG1_PHYS (IXP23XX_PERIPHERAL_PHYS + 0xC000)
-#define IXP23XX_DDRS_PHYS (IXP23XX_PERIPHERAL_PHYS + 0xD000)
-
-
-/****************************************************************************
- * Interrupt controller.
- ****************************************************************************/
-#define IXP23XX_INTC_REG(x) ((volatile unsigned long *)(IXP23XX_INTC_VIRT + (x)))
-#define IXP23XX_INTR_ST1 IXP23XX_INTC_REG(0x00)
-#define IXP23XX_INTR_ST2 IXP23XX_INTC_REG(0x04)
-#define IXP23XX_INTR_ST3 IXP23XX_INTC_REG(0x08)
-#define IXP23XX_INTR_ST4 IXP23XX_INTC_REG(0x0c)
-#define IXP23XX_INTR_EN1 IXP23XX_INTC_REG(0x10)
-#define IXP23XX_INTR_EN2 IXP23XX_INTC_REG(0x14)
-#define IXP23XX_INTR_EN3 IXP23XX_INTC_REG(0x18)
-#define IXP23XX_INTR_EN4 IXP23XX_INTC_REG(0x1c)
-#define IXP23XX_INTR_SEL1 IXP23XX_INTC_REG(0x20)
-#define IXP23XX_INTR_SEL2 IXP23XX_INTC_REG(0x24)
-#define IXP23XX_INTR_SEL3 IXP23XX_INTC_REG(0x28)
-#define IXP23XX_INTR_SEL4 IXP23XX_INTC_REG(0x2c)
-#define IXP23XX_INTR_IRQ_ST1 IXP23XX_INTC_REG(0x30)
-#define IXP23XX_INTR_IRQ_ST2 IXP23XX_INTC_REG(0x34)
-#define IXP23XX_INTR_IRQ_ST3 IXP23XX_INTC_REG(0x38)
-#define IXP23XX_INTR_IRQ_ST4 IXP23XX_INTC_REG(0x3c)
-#define IXP23XX_INTR_IRQ_ENC_ST_OFFSET 0x54
-
-
-/****************************************************************************
- * GPIO.
- ****************************************************************************/
-#define IXP23XX_GPIO_REG(x) ((volatile unsigned long *)(IXP23XX_GPIO_VIRT + (x)))
-#define IXP23XX_GPIO_GPOUTR IXP23XX_GPIO_REG(0x00)
-#define IXP23XX_GPIO_GPOER IXP23XX_GPIO_REG(0x04)
-#define IXP23XX_GPIO_GPINR IXP23XX_GPIO_REG(0x08)
-#define IXP23XX_GPIO_GPISR IXP23XX_GPIO_REG(0x0c)
-#define IXP23XX_GPIO_GPIT1R IXP23XX_GPIO_REG(0x10)
-#define IXP23XX_GPIO_GPIT2R IXP23XX_GPIO_REG(0x14)
-#define IXP23XX_GPIO_GPCLKR IXP23XX_GPIO_REG(0x18)
-#define IXP23XX_GPIO_GPDBSELR IXP23XX_GPIO_REG(0x1c)
-
-#define IXP23XX_GPIO_STYLE_MASK 0x7
-#define IXP23XX_GPIO_STYLE_ACTIVE_HIGH 0x0
-#define IXP23XX_GPIO_STYLE_ACTIVE_LOW 0x1
-#define IXP23XX_GPIO_STYLE_RISING_EDGE 0x2
-#define IXP23XX_GPIO_STYLE_FALLING_EDGE 0x3
-#define IXP23XX_GPIO_STYLE_TRANSITIONAL 0x4
-
-#define IXP23XX_GPIO_STYLE_SIZE 3
-
-
-/****************************************************************************
- * Timer.
- ****************************************************************************/
-#define IXP23XX_TIMER_REG(x) ((volatile unsigned long *)(IXP23XX_TIMER_VIRT + (x)))
-#define IXP23XX_TIMER_CONT IXP23XX_TIMER_REG(0x00)
-#define IXP23XX_TIMER1_TIMESTAMP IXP23XX_TIMER_REG(0x04)
-#define IXP23XX_TIMER1_RELOAD IXP23XX_TIMER_REG(0x08)
-#define IXP23XX_TIMER2_TIMESTAMP IXP23XX_TIMER_REG(0x0c)
-#define IXP23XX_TIMER2_RELOAD IXP23XX_TIMER_REG(0x10)
-#define IXP23XX_TIMER_WDOG IXP23XX_TIMER_REG(0x14)
-#define IXP23XX_TIMER_WDOG_EN IXP23XX_TIMER_REG(0x18)
-#define IXP23XX_TIMER_WDOG_KEY IXP23XX_TIMER_REG(0x1c)
-#define IXP23XX_TIMER_WDOG_KEY_MAGIC 0x482e
-#define IXP23XX_TIMER_STATUS IXP23XX_TIMER_REG(0x20)
-#define IXP23XX_TIMER_SOFT_RESET IXP23XX_TIMER_REG(0x24)
-#define IXP23XX_TIMER_SOFT_RESET_EN IXP23XX_TIMER_REG(0x28)
-
-#define IXP23XX_TIMER_ENABLE (1 << 0)
-#define IXP23XX_TIMER_ONE_SHOT (1 << 1)
-/* Low order bits of reload value ignored */
-#define IXP23XX_TIMER_RELOAD_MASK (0x3)
-#define IXP23XX_TIMER_DISABLED (0x0)
-#define IXP23XX_TIMER1_INT_PEND (1 << 0)
-#define IXP23XX_TIMER2_INT_PEND (1 << 1)
-#define IXP23XX_TIMER_STATUS_TS_PEND (1 << 2)
-#define IXP23XX_TIMER_STATUS_WDOG_PEND (1 << 3)
-#define IXP23XX_TIMER_STATUS_WARM_RESET (1 << 4)
-
-
-/****************************************************************************
- * CAP CSRs.
- ****************************************************************************/
-#define IXP23XX_GLOBAL_REG(x) ((volatile unsigned long *)(IXP23XX_CAP_CSR_VIRT + 0x4a00 + (x)))
-#define IXP23XX_PRODUCT_ID IXP23XX_GLOBAL_REG(0x00)
-#define IXP23XX_MISC_CONTROL IXP23XX_GLOBAL_REG(0x04)
-#define IXP23XX_MSF_CLK_CNTRL IXP23XX_GLOBAL_REG(0x08)
-#define IXP23XX_RESET0 IXP23XX_GLOBAL_REG(0x0c)
-#define IXP23XX_RESET1 IXP23XX_GLOBAL_REG(0x10)
-#define IXP23XX_STRAP_OPTIONS IXP23XX_GLOBAL_REG(0x18)
-
-#define IXP23XX_ENABLE_WATCHDOG (1 << 24)
-#define IXP23XX_SHPC_INIT_COMP (1 << 21)
-#define IXP23XX_RST_ALL (1 << 16)
-#define IXP23XX_RESET_PCI (1 << 2)
-#define IXP23XX_PCI_UNIT_RESET (1 << 1)
-#define IXP23XX_XSCALE_RESET (1 << 0)
-
-#define IXP23XX_UENGINE_CSR_VIRT_BASE (IXP23XX_CAP_CSR_VIRT + 0x18000)
-
-
-/****************************************************************************
- * PCI CSRs.
- ****************************************************************************/
-#define IXP23XX_PCI_CREG(x) ((volatile unsigned long *)(IXP23XX_PCI_CREG_VIRT + (x)))
-#define IXP23XX_PCI_CMDSTAT IXP23XX_PCI_CREG(0x04)
-#define IXP23XX_PCI_SRAM_BAR IXP23XX_PCI_CREG(0x14)
-#define IXP23XX_PCI_SDRAM_BAR IXP23XX_PCI_CREG(0x18)
-
-
-#define IXP23XX_PCI_CSR(x) ((volatile unsigned long *)(IXP23XX_PCI_CREG_VIRT + 0x01000000 + (x)))
-#define IXP23XX_PCI_OUT_INT_STATUS IXP23XX_PCI_CSR(0x0030)
-#define IXP23XX_PCI_OUT_INT_MASK IXP23XX_PCI_CSR(0x0034)
-#define IXP23XX_PCI_SRAM_BASE_ADDR_MASK IXP23XX_PCI_CSR(0x00fc)
-#define IXP23XX_PCI_DRAM_BASE_ADDR_MASK IXP23XX_PCI_CSR(0x0100)
-#define IXP23XX_PCI_CONTROL IXP23XX_PCI_CSR(0x013c)
-#define IXP23XX_PCI_ADDR_EXT IXP23XX_PCI_CSR(0x0140)
-#define IXP23XX_PCI_ME_PUSH_STATUS IXP23XX_PCI_CSR(0x0148)
-#define IXP23XX_PCI_ME_PUSH_EN IXP23XX_PCI_CSR(0x014c)
-#define IXP23XX_PCI_ERR_STATUS IXP23XX_PCI_CSR(0x0150)
-#define IXP23XX_PCI_ERROR_STATUS IXP23XX_PCI_CSR(0x0150)
-#define IXP23XX_PCI_ERR_ENABLE IXP23XX_PCI_CSR(0x0154)
-#define IXP23XX_PCI_XSCALE_INT_STATUS IXP23XX_PCI_CSR(0x0158)
-#define IXP23XX_PCI_XSCALE_INT_ENABLE IXP23XX_PCI_CSR(0x015c)
-#define IXP23XX_PCI_CPP_ADDR_BITS IXP23XX_PCI_CSR(0x0160)
-
-
-#endif
+++ /dev/null
-/*
- * arch/arm/mach-ixp23xx/include/mach/memory.h
- *
- * Copyright (c) 2003-2004 Intel Corp.
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- */
-
-#ifndef __ASM_ARCH_MEMORY_H
-#define __ASM_ARCH_MEMORY_H
-
-#include <mach/hardware.h>
-
-/*
- * Physical DRAM offset.
- */
-#define PLAT_PHYS_OFFSET (0x00000000)
-
-#define IXP23XX_PCI_SDRAM_OFFSET (*((volatile int *)IXP23XX_PCI_SDRAM_BAR) & 0xfffffff0)
-
-#define __phys_to_bus(x) ((x) + (IXP23XX_PCI_SDRAM_OFFSET - PHYS_OFFSET))
-#define __bus_to_phys(x) ((x) - (IXP23XX_PCI_SDRAM_OFFSET - PHYS_OFFSET))
-
-#define __virt_to_bus(v) __phys_to_bus(__virt_to_phys(v))
-#define __bus_to_virt(b) __phys_to_virt(__bus_to_phys(b))
-#define __pfn_to_bus(p) __phys_to_bus(__pfn_to_phys(p))
-#define __bus_to_pfn(b) __phys_to_pfn(__bus_to_phys(b))
-
-#define arch_is_coherent() 1
-
-#endif
+++ /dev/null
-/*
- * arch/arm/mach-ixp23xx/include/mach/platform.h
- *
- * Various bits of code used by platform-level code.
- *
- * Author: Deepak Saxena <dsaxena@plexity.net>
- *
- * Copyright 2005 (c) MontaVista Software, Inc.
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#ifndef __ASSEMBLY__
-
-static inline unsigned long ixp2000_reg_read(volatile void *reg)
-{
- return *((volatile unsigned long *)reg);
-}
-
-static inline void ixp2000_reg_write(volatile void *reg, unsigned long val)
-{
- *((volatile unsigned long *)reg) = val;
-}
-
-static inline void ixp2000_reg_wrb(volatile void *reg, unsigned long val)
-{
- *((volatile unsigned long *)reg) = val;
-}
-
-struct pci_sys_data;
-
-void ixp23xx_map_io(void);
-void ixp23xx_init_irq(void);
-void ixp23xx_sys_init(void);
-void ixp23xx_restart(char, const char *);
-int ixp23xx_pci_setup(int, struct pci_sys_data *);
-void ixp23xx_pci_preinit(void);
-struct pci_bus *ixp23xx_pci_scan_bus(int, struct pci_sys_data*);
-void ixp23xx_pci_slave_init(void);
-
-extern struct sys_timer ixp23xx_timer;
-
-#define IXP23XX_UART_XTAL 14745600
-
-#ifndef __ASSEMBLY__
-/*
- * Is system memory on the XSI or CPP bus?
- */
-static inline unsigned ixp23xx_cpp_boot(void)
-{
- return (*IXP23XX_EXP_CFG0 & IXP23XX_EXP_CFG0_XSI_NOT_PRES);
-}
-#endif
-
-
-#endif
+++ /dev/null
-/*
- * arch/arm/mach-ixp23xx/include/mach/time.h
- */
+++ /dev/null
-/*
- * arch/arm/mach-ixp23xx/include/mach/timex.h
- *
- * XScale architecture timex specifications
- */
-
-#define CLOCK_TICK_RATE 75000000
+++ /dev/null
-/*
- * arch/arm/mach-ixp23xx/include/mach/uncompress.h
- *
- * Copyright (C) 2002-2004 Intel Corporation.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#ifndef __ASM_ARCH_UNCOMPRESS_H
-#define __ASM_ARCH_UNCOMPRESS_H
-
-#include <mach/ixp23xx.h>
-#include <linux/serial_reg.h>
-
-#define UART_BASE ((volatile u32 *)IXP23XX_UART1_PHYS)
-
-static inline void putc(char c)
-{
- int j;
-
- for (j = 0; j < 0x1000; j++) {
- if (UART_BASE[UART_LSR] & UART_LSR_THRE)
- break;
- barrier();
- }
-
- UART_BASE[UART_TX] = c;
-}
-
-static inline void flush(void)
-{
-}
-
-#define arch_decomp_setup()
-#define arch_decomp_wdog()
-
-
-#endif
+++ /dev/null
-/*
- * arch/arm/mach-ixp23xx/ixdp2351.c
- *
- * IXDP2351 board-specific routines
- *
- * Author: Deepak Saxena <dsaxena@plexity.net>
- *
- * Copyright 2005 (c) MontaVista Software, Inc.
- *
- * Based on 2.4 code Copyright 2004 (c) Intel Corporation
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/spinlock.h>
-#include <linux/sched.h>
-#include <linux/interrupt.h>
-#include <linux/irq.h>
-#include <linux/serial.h>
-#include <linux/tty.h>
-#include <linux/bitops.h>
-#include <linux/ioport.h>
-#include <linux/serial_8250.h>
-#include <linux/serial_core.h>
-#include <linux/device.h>
-#include <linux/mm.h>
-#include <linux/pci.h>
-#include <linux/mtd/physmap.h>
-
-#include <asm/types.h>
-#include <asm/setup.h>
-#include <asm/memory.h>
-#include <mach/hardware.h>
-#include <asm/mach-types.h>
-#include <asm/tlbflush.h>
-#include <asm/pgtable.h>
-
-#include <asm/mach/map.h>
-#include <asm/mach/irq.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/pci.h>
-
-/*
- * IXDP2351 Interrupt Handling
- */
-static void ixdp2351_inta_mask(struct irq_data *d)
-{
- *IXDP2351_CPLD_INTA_MASK_SET_REG = IXDP2351_INTA_IRQ_MASK(d->irq);
-}
-
-static void ixdp2351_inta_unmask(struct irq_data *d)
-{
- *IXDP2351_CPLD_INTA_MASK_CLR_REG = IXDP2351_INTA_IRQ_MASK(d->irq);
-}
-
-static void ixdp2351_inta_handler(unsigned int irq, struct irq_desc *desc)
-{
- u16 ex_interrupt =
- *IXDP2351_CPLD_INTA_STAT_REG & IXDP2351_INTA_IRQ_VALID;
- int i;
-
- desc->irq_data.chip->irq_mask(&desc->irq_data);
-
- for (i = 0; i < IXDP2351_INTA_IRQ_NUM; i++) {
- if (ex_interrupt & (1 << i)) {
- int cpld_irq =
- IXP23XX_MACH_IRQ(IXDP2351_INTA_IRQ_BASE + i);
- generic_handle_irq(cpld_irq);
- }
- }
-
- desc->irq_data.chip->irq_unmask(&desc->irq_data);
-}
-
-static struct irq_chip ixdp2351_inta_chip = {
- .irq_ack = ixdp2351_inta_mask,
- .irq_mask = ixdp2351_inta_mask,
- .irq_unmask = ixdp2351_inta_unmask
-};
-
-static void ixdp2351_intb_mask(struct irq_data *d)
-{
- *IXDP2351_CPLD_INTB_MASK_SET_REG = IXDP2351_INTB_IRQ_MASK(d->irq);
-}
-
-static void ixdp2351_intb_unmask(struct irq_data *d)
-{
- *IXDP2351_CPLD_INTB_MASK_CLR_REG = IXDP2351_INTB_IRQ_MASK(d->irq);
-}
-
-static void ixdp2351_intb_handler(unsigned int irq, struct irq_desc *desc)
-{
- u16 ex_interrupt =
- *IXDP2351_CPLD_INTB_STAT_REG & IXDP2351_INTB_IRQ_VALID;
- int i;
-
- desc->irq_data.chip->irq_ack(&desc->irq_data);
-
- for (i = 0; i < IXDP2351_INTB_IRQ_NUM; i++) {
- if (ex_interrupt & (1 << i)) {
- int cpld_irq =
- IXP23XX_MACH_IRQ(IXDP2351_INTB_IRQ_BASE + i);
- generic_handle_irq(cpld_irq);
- }
- }
-
- desc->irq_data.chip->irq_unmask(&desc->irq_data);
-}
-
-static struct irq_chip ixdp2351_intb_chip = {
- .irq_ack = ixdp2351_intb_mask,
- .irq_mask = ixdp2351_intb_mask,
- .irq_unmask = ixdp2351_intb_unmask
-};
-
-void __init ixdp2351_init_irq(void)
-{
- int irq;
-
- /* Mask all interrupts from CPLD, disable simulation */
- *IXDP2351_CPLD_INTA_MASK_SET_REG = (u16) -1;
- *IXDP2351_CPLD_INTB_MASK_SET_REG = (u16) -1;
- *IXDP2351_CPLD_INTA_SIM_REG = 0;
- *IXDP2351_CPLD_INTB_SIM_REG = 0;
-
- ixp23xx_init_irq();
-
- for (irq = IXP23XX_MACH_IRQ(IXDP2351_INTA_IRQ_BASE);
- irq <
- IXP23XX_MACH_IRQ(IXDP2351_INTA_IRQ_BASE + IXDP2351_INTA_IRQ_NUM);
- irq++) {
- if (IXDP2351_INTA_IRQ_MASK(irq) & IXDP2351_INTA_IRQ_VALID) {
- set_irq_flags(irq, IRQF_VALID);
- irq_set_chip_and_handler(irq, &ixdp2351_inta_chip,
- handle_level_irq);
- }
- }
-
- for (irq = IXP23XX_MACH_IRQ(IXDP2351_INTB_IRQ_BASE);
- irq <
- IXP23XX_MACH_IRQ(IXDP2351_INTB_IRQ_BASE + IXDP2351_INTB_IRQ_NUM);
- irq++) {
- if (IXDP2351_INTB_IRQ_MASK(irq) & IXDP2351_INTB_IRQ_VALID) {
- set_irq_flags(irq, IRQF_VALID);
- irq_set_chip_and_handler(irq, &ixdp2351_intb_chip,
- handle_level_irq);
- }
- }
-
- irq_set_chained_handler(IRQ_IXP23XX_INTA, ixdp2351_inta_handler);
- irq_set_chained_handler(IRQ_IXP23XX_INTB, ixdp2351_intb_handler);
-}
-
-/*
- * IXDP2351 PCI
- */
-
-/*
- * This board does not do normal PCI IRQ routing, or any
- * sort of swizzling, so we just need to check where on the
- * bus the device is and figure out what CPLD pin it is
- * being routed to.
- */
-#define DEVPIN(dev, pin) ((pin) | ((dev) << 3))
-
-static int __init ixdp2351_map_irq(const struct pci_dev *dev, u8 slot, u8 pin)
-{
- u8 bus = dev->bus->number;
- u32 devpin = DEVPIN(PCI_SLOT(dev->devfn), pin);
- struct pci_bus *tmp_bus = dev->bus;
-
- /* Primary bus, no interrupts here */
- if (!bus)
- return -1;
-
- /* Lookup first leaf in bus tree */
- while ((tmp_bus->parent != NULL) && (tmp_bus->parent->parent != NULL))
- tmp_bus = tmp_bus->parent;
-
- /* Select between known bridges */
- switch (tmp_bus->self->devfn | (tmp_bus->self->bus->number << 8)) {
- /* Device is located after first bridge */
- case 0x0008:
- if (tmp_bus == dev->bus) {
- /* Device is located directy after first bridge */
- switch (devpin) {
- /* Onboard 82546 */
- case DEVPIN(1, 1): /* Onboard 82546 ch 0 */
- return IRQ_IXDP2351_INTA_82546;
- case DEVPIN(1, 2): /* Onboard 82546 ch 1 */
- return IRQ_IXDP2351_INTB_82546;
- /* PMC SLOT */
- case DEVPIN(0, 1): /* PMCP INTA# */
- case DEVPIN(2, 4): /* PMCS INTD# */
- return IRQ_IXDP2351_SPCI_PMC_INTA;
- case DEVPIN(0, 2): /* PMCP INTB# */
- case DEVPIN(2, 1): /* PMCS INTA# */
- return IRQ_IXDP2351_SPCI_PMC_INTB;
- case DEVPIN(0, 3): /* PMCP INTC# */
- case DEVPIN(2, 2): /* PMCS INTB# */
- return IRQ_IXDP2351_SPCI_PMC_INTC;
- case DEVPIN(0, 4): /* PMCP INTD# */
- case DEVPIN(2, 3): /* PMCS INTC# */
- return IRQ_IXDP2351_SPCI_PMC_INTD;
- }
- } else {
- /* Device is located indirectly after first bridge */
- /* Not supported now */
- return -1;
- }
- break;
- case 0x0010:
- if (tmp_bus == dev->bus) {
- /* Device is located directy after second bridge */
- /* Secondary bus of second bridge */
- switch (devpin) {
- case DEVPIN(0, 1): /* DB#0 */
- case DEVPIN(0, 2):
- case DEVPIN(0, 3):
- case DEVPIN(0, 4):
- return IRQ_IXDP2351_SPCI_DB_0;
- case DEVPIN(1, 1): /* DB#1 */
- case DEVPIN(1, 2):
- case DEVPIN(1, 3):
- case DEVPIN(1, 4):
- return IRQ_IXDP2351_SPCI_DB_1;
- case DEVPIN(2, 1): /* FIC1 */
- case DEVPIN(2, 2):
- case DEVPIN(2, 3):
- case DEVPIN(2, 4):
- case DEVPIN(3, 1): /* FIC2 */
- case DEVPIN(3, 2):
- case DEVPIN(3, 3):
- case DEVPIN(3, 4):
- return IRQ_IXDP2351_SPCI_FIC;
- }
- } else {
- /* Device is located indirectly after second bridge */
- /* Not supported now */
- return -1;
- }
- break;
- }
-
- return -1;
-}
-
-struct hw_pci ixdp2351_pci __initdata = {
- .nr_controllers = 1,
- .preinit = ixp23xx_pci_preinit,
- .setup = ixp23xx_pci_setup,
- .scan = ixp23xx_pci_scan_bus,
- .map_irq = ixdp2351_map_irq,
-};
-
-int __init ixdp2351_pci_init(void)
-{
- if (machine_is_ixdp2351())
- pci_common_init(&ixdp2351_pci);
-
- return 0;
-}
-
-subsys_initcall(ixdp2351_pci_init);
-
-/*
- * IXDP2351 Static Mapped I/O
- */
-static struct map_desc ixdp2351_io_desc[] __initdata = {
- {
- .virtual = IXDP2351_NP_VIRT_BASE,
- .pfn = __phys_to_pfn((u64)IXDP2351_NP_PHYS_BASE),
- .length = IXDP2351_NP_PHYS_SIZE,
- .type = MT_DEVICE
- }, {
- .virtual = IXDP2351_BB_BASE_VIRT,
- .pfn = __phys_to_pfn((u64)IXDP2351_BB_BASE_PHYS),
- .length = IXDP2351_BB_SIZE,
- .type = MT_DEVICE
- }
-};
-
-static void __init ixdp2351_map_io(void)
-{
- ixp23xx_map_io();
- iotable_init(ixdp2351_io_desc, ARRAY_SIZE(ixdp2351_io_desc));
-}
-
-static struct physmap_flash_data ixdp2351_flash_data = {
- .width = 1,
-};
-
-static struct resource ixdp2351_flash_resource = {
- .start = 0x90000000,
- .end = 0x93ffffff,
- .flags = IORESOURCE_MEM,
-};
-
-static struct platform_device ixdp2351_flash = {
- .name = "physmap-flash",
- .id = 0,
- .dev = {
- .platform_data = &ixdp2351_flash_data,
- },
- .num_resources = 1,
- .resource = &ixdp2351_flash_resource,
-};
-
-static void __init ixdp2351_init(void)
-{
- platform_device_register(&ixdp2351_flash);
-
- /*
- * Mark flash as writeable
- */
- IXP23XX_EXP_CS0[0] |= IXP23XX_FLASH_WRITABLE;
- IXP23XX_EXP_CS0[1] |= IXP23XX_FLASH_WRITABLE;
- IXP23XX_EXP_CS0[2] |= IXP23XX_FLASH_WRITABLE;
- IXP23XX_EXP_CS0[3] |= IXP23XX_FLASH_WRITABLE;
-
- ixp23xx_sys_init();
-}
-
-static void ixdp2351_restart(char mode, const char *cmd)
-{
- /* First try machine specific support */
-
- *IXDP2351_CPLD_RESET1_REG = IXDP2351_CPLD_RESET1_MAGIC;
- (void) *IXDP2351_CPLD_RESET1_REG;
- *IXDP2351_CPLD_RESET1_REG = IXDP2351_CPLD_RESET1_ENABLE;
-
- ixp23xx_restart(mode, cmd);
-}
-
-MACHINE_START(IXDP2351, "Intel IXDP2351 Development Platform")
- /* Maintainer: MontaVista Software, Inc. */
- .map_io = ixdp2351_map_io,
- .init_irq = ixdp2351_init_irq,
- .timer = &ixp23xx_timer,
- .atag_offset = 0x100,
- .init_machine = ixdp2351_init,
- .restart = ixdp2351_restart,
-MACHINE_END
+++ /dev/null
-/*
- * arch/arm/mach-ixp23xx/pci.c
- *
- * PCI routines for IXP23XX based systems
- *
- * Copyright (c) 2005 MontaVista Software, Inc.
- *
- * based on original code:
- *
- * Author: Naeem Afzal <naeem.m.afzal@intel.com>
- * Copyright 2002-2005 Intel Corp.
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- */
-
-#include <linux/sched.h>
-#include <linux/kernel.h>
-#include <linux/pci.h>
-#include <linux/interrupt.h>
-#include <linux/mm.h>
-#include <linux/init.h>
-#include <linux/ioport.h>
-#include <linux/delay.h>
-#include <linux/io.h>
-
-#include <asm/irq.h>
-#include <asm/sizes.h>
-#include <asm/mach/pci.h>
-#include <mach/hardware.h>
-
-extern int (*external_fault) (unsigned long, struct pt_regs *);
-
-static volatile int pci_master_aborts = 0;
-
-#ifdef DEBUG
-#define DBG(x...) printk(x)
-#else
-#define DBG(x...)
-#endif
-
-int clear_master_aborts(void);
-
-static u32
-*ixp23xx_pci_config_addr(unsigned int bus_nr, unsigned int devfn, int where)
-{
- u32 *paddress;
-
- /*
- * Must be dword aligned
- */
- where &= ~3;
-
- /*
- * For top bus, generate type 0, else type 1
- */
- if (!bus_nr) {
- if (PCI_SLOT(devfn) >= 8)
- return 0;
-
- paddress = (u32 *) (IXP23XX_PCI_CFG0_VIRT
- | (1 << (PCI_SLOT(devfn) + 16))
- | (PCI_FUNC(devfn) << 8) | where);
- } else {
- paddress = (u32 *) (IXP23XX_PCI_CFG1_VIRT
- | (bus_nr << 16)
- | (PCI_SLOT(devfn) << 11)
- | (PCI_FUNC(devfn) << 8) | where);
- }
-
- return paddress;
-}
-
-/*
- * Mask table, bits to mask for quantity of size 1, 2 or 4 bytes.
- * 0 and 3 are not valid indexes...
- */
-static u32 bytemask[] = {
- /*0*/ 0,
- /*1*/ 0xff,
- /*2*/ 0xffff,
- /*3*/ 0,
- /*4*/ 0xffffffff,
-};
-
-static int ixp23xx_pci_read_config(struct pci_bus *bus, unsigned int devfn,
- int where, int size, u32 *value)
-{
- u32 n;
- u32 *addr;
-
- n = where % 4;
-
- DBG("In config_read(%d) %d from dev %d:%d:%d\n", size, where,
- bus->number, PCI_SLOT(devfn), PCI_FUNC(devfn));
-
- addr = ixp23xx_pci_config_addr(bus->number, devfn, where);
- if (!addr)
- return PCIBIOS_DEVICE_NOT_FOUND;
-
- pci_master_aborts = 0;
- *value = (*addr >> (8*n)) & bytemask[size];
- if (pci_master_aborts) {
- pci_master_aborts = 0;
- *value = 0xffffffff;
- return PCIBIOS_DEVICE_NOT_FOUND;
- }
-
- return PCIBIOS_SUCCESSFUL;
-}
-
-/*
- * We don't do error checking on the address for writes.
- * It's assumed that the user checked for the device existing first
- * by doing a read first.
- */
-static int ixp23xx_pci_write_config(struct pci_bus *bus, unsigned int devfn,
- int where, int size, u32 value)
-{
- u32 mask;
- u32 *addr;
- u32 temp;
-
- mask = ~(bytemask[size] << ((where % 0x4) * 8));
- addr = ixp23xx_pci_config_addr(bus->number, devfn, where);
- if (!addr)
- return PCIBIOS_DEVICE_NOT_FOUND;
- temp = (u32) (value) << ((where % 0x4) * 8);
- *addr = (*addr & mask) | temp;
-
- clear_master_aborts();
-
- return PCIBIOS_SUCCESSFUL;
-}
-
-struct pci_ops ixp23xx_pci_ops = {
- .read = ixp23xx_pci_read_config,
- .write = ixp23xx_pci_write_config,
-};
-
-struct pci_bus *ixp23xx_pci_scan_bus(int nr, struct pci_sys_data *sysdata)
-{
- return pci_scan_root_bus(NULL, sysdata->busnr, &ixp23xx_pci_ops,
- sysdata, &sysdata->resources);
-}
-
-int ixp23xx_pci_abort_handler(unsigned long addr, unsigned int fsr, struct pt_regs *regs)
-{
- volatile unsigned long temp;
- unsigned long flags;
-
- pci_master_aborts = 1;
-
- local_irq_save(flags);
- temp = *IXP23XX_PCI_CONTROL;
-
- /*
- * master abort and cmd tgt err
- */
- if (temp & ((1 << 8) | (1 << 5)))
- *IXP23XX_PCI_CONTROL = temp;
-
- temp = *IXP23XX_PCI_CMDSTAT;
-
- if (temp & (1 << 29))
- *IXP23XX_PCI_CMDSTAT = temp;
- local_irq_restore(flags);
-
- /*
- * If it was an imprecise abort, then we need to correct the
- * return address to be _after_ the instruction.
- */
- if (fsr & (1 << 10))
- regs->ARM_pc += 4;
-
- return 0;
-}
-
-int clear_master_aborts(void)
-{
- volatile u32 temp;
-
- temp = *IXP23XX_PCI_CONTROL;
-
- /*
- * master abort and cmd tgt err
- */
- if (temp & ((1 << 8) | (1 << 5)))
- *IXP23XX_PCI_CONTROL = temp;
-
- temp = *IXP23XX_PCI_CMDSTAT;
-
- if (temp & (1 << 29))
- *IXP23XX_PCI_CMDSTAT = temp;
-
- return 0;
-}
-
-static void __init ixp23xx_pci_common_init(void)
-{
-#ifdef __ARMEB__
- *IXP23XX_PCI_CONTROL |= 0x20000; /* set I/O swapping */
-#endif
- /*
- * ADDR_31 needs to be clear for PCI memory access to CPP memory
- */
- *IXP23XX_CPP2XSI_CURR_XFER_REG3 &= ~IXP23XX_CPP2XSI_ADDR_31;
- *IXP23XX_CPP2XSI_CURR_XFER_REG3 |= IXP23XX_CPP2XSI_PSH_OFF;
-
- /*
- * Select correct memory for PCI inbound transactions
- */
- if (ixp23xx_cpp_boot()) {
- *IXP23XX_PCI_CPP_ADDR_BITS &= ~(1 << 1);
- } else {
- *IXP23XX_PCI_CPP_ADDR_BITS |= (1 << 1);
-
- /*
- * Enable coherency on A2 silicon.
- */
- if (arch_is_coherent())
- *IXP23XX_CPP2XSI_CURR_XFER_REG3 &= ~IXP23XX_CPP2XSI_COH_OFF;
- }
-}
-
-void __init ixp23xx_pci_preinit(void)
-{
- pcibios_min_io = 0;
- pcibios_min_mem = 0xe0000000;
-
- pci_set_flags(0);
-
- ixp23xx_pci_common_init();
-
- hook_fault_code(16+6, ixp23xx_pci_abort_handler, SIGBUS, 0,
- "PCI config cycle to non-existent device");
-
- *IXP23XX_PCI_ADDR_EXT = 0x0000e000;
-}
-
-/*
- * Prevent PCI layer from seeing the inbound host-bridge resources
- */
-static void __devinit pci_fixup_ixp23xx(struct pci_dev *dev)
-{
- int i;
-
- dev->class &= 0xff;
- dev->class |= PCI_CLASS_BRIDGE_HOST << 8;
- for (i = 0; i < PCI_NUM_RESOURCES; i++) {
- dev->resource[i].start = 0;
- dev->resource[i].end = 0;
- dev->resource[i].flags = 0;
- }
-}
-DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x9002, pci_fixup_ixp23xx);
-
-/*
- * IXP2300 systems often have large resource requirements, so we just
- * use our own resource space.
- */
-static struct resource ixp23xx_pci_mem_space = {
- .start = IXP23XX_PCI_MEM_START,
- .end = IXP23XX_PCI_MEM_START + IXP23XX_PCI_MEM_SIZE - 1,
- .flags = IORESOURCE_MEM,
- .name = "PCI Mem Space"
-};
-
-static struct resource ixp23xx_pci_io_space = {
- .start = 0x00000100,
- .end = 0x01ffffff,
- .flags = IORESOURCE_IO,
- .name = "PCI I/O Space"
-};
-
-int ixp23xx_pci_setup(int nr, struct pci_sys_data *sys)
-{
- if (nr >= 1)
- return 0;
-
- pci_add_resource_offset(&sys->resources,
- &ixp23xx_pci_io_space, sys->io_offset);
- pci_add_resource_offset(&sys->resources,
- &ixp23xx_pci_mem_space, sys->mem_offset);
-
- return 1;
-}
-
-void __init ixp23xx_pci_slave_init(void)
-{
- ixp23xx_pci_common_init();
-}
+++ /dev/null
-/*
- * arch/arm/mach-ixp23xx/roadrunner.c
- *
- * RoadRunner board-specific routines
- *
- * Author: Deepak Saxena <dsaxena@plexity.net>
- *
- * Copyright 2005 (c) MontaVista Software, Inc.
- *
- * Based on 2.4 code Copyright 2005 (c) ADI Engineering Corporation
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/spinlock.h>
-#include <linux/sched.h>
-#include <linux/interrupt.h>
-#include <linux/serial.h>
-#include <linux/tty.h>
-#include <linux/bitops.h>
-#include <linux/ioport.h>
-#include <linux/serial_8250.h>
-#include <linux/serial_core.h>
-#include <linux/device.h>
-#include <linux/mm.h>
-#include <linux/pci.h>
-#include <linux/mtd/physmap.h>
-
-#include <asm/types.h>
-#include <asm/setup.h>
-#include <asm/memory.h>
-#include <mach/hardware.h>
-#include <asm/mach-types.h>
-#include <asm/irq.h>
-#include <asm/tlbflush.h>
-#include <asm/pgtable.h>
-
-#include <asm/mach/map.h>
-#include <asm/mach/irq.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/pci.h>
-
-/*
- * Interrupt mapping
- */
-#define INTA IRQ_ROADRUNNER_PCI_INTA
-#define INTB IRQ_ROADRUNNER_PCI_INTB
-#define INTC IRQ_ROADRUNNER_PCI_INTC
-#define INTD IRQ_ROADRUNNER_PCI_INTD
-
-#define INTC_PIN IXP23XX_GPIO_PIN_11
-#define INTD_PIN IXP23XX_GPIO_PIN_12
-
-static int __init roadrunner_map_irq(const struct pci_dev *dev, u8 idsel,
- u8 pin)
-{
- static int pci_card_slot_irq[] = {INTB, INTC, INTD, INTA};
- static int pmc_card_slot_irq[] = {INTA, INTB, INTC, INTD};
- static int usb_irq[] = {INTB, INTC, INTD, -1};
- static int mini_pci_1_irq[] = {INTB, INTC, -1, -1};
- static int mini_pci_2_irq[] = {INTC, INTD, -1, -1};
-
- switch(dev->bus->number) {
- case 0:
- switch(dev->devfn) {
- case 0x0: // PCI-PCI bridge
- break;
- case 0x8: // PCI Card Slot
- return pci_card_slot_irq[pin - 1];
- case 0x10: // PMC Slot
- return pmc_card_slot_irq[pin - 1];
- case 0x18: // PMC Slot Secondary Agent
- break;
- case 0x20: // IXP Processor
- break;
- default:
- return NO_IRQ;
- }
- break;
-
- case 1:
- switch(dev->devfn) {
- case 0x0: // IDE Controller
- return (pin == 1) ? INTC : -1;
- case 0x8: // USB fun 0
- case 0x9: // USB fun 1
- case 0xa: // USB fun 2
- return usb_irq[pin - 1];
- case 0x10: // Mini PCI 1
- return mini_pci_1_irq[pin-1];
- case 0x18: // Mini PCI 2
- return mini_pci_2_irq[pin-1];
- case 0x20: // MEM slot
- return (pin == 1) ? INTA : -1;
- default:
- return NO_IRQ;
- }
- break;
-
- default:
- return NO_IRQ;
- }
-
- return NO_IRQ;
-}
-
-static void __init roadrunner_pci_preinit(void)
-{
- irq_set_irq_type(IRQ_ROADRUNNER_PCI_INTC, IRQ_TYPE_LEVEL_LOW);
- irq_set_irq_type(IRQ_ROADRUNNER_PCI_INTD, IRQ_TYPE_LEVEL_LOW);
-
- ixp23xx_pci_preinit();
-}
-
-static struct hw_pci roadrunner_pci __initdata = {
- .nr_controllers = 1,
- .preinit = roadrunner_pci_preinit,
- .setup = ixp23xx_pci_setup,
- .scan = ixp23xx_pci_scan_bus,
- .map_irq = roadrunner_map_irq,
-};
-
-static int __init roadrunner_pci_init(void)
-{
- if (machine_is_roadrunner())
- pci_common_init(&roadrunner_pci);
-
- return 0;
-};
-
-subsys_initcall(roadrunner_pci_init);
-
-static struct physmap_flash_data roadrunner_flash_data = {
- .width = 2,
-};
-
-static struct resource roadrunner_flash_resource = {
- .start = 0x90000000,
- .end = 0x93ffffff,
- .flags = IORESOURCE_MEM,
-};
-
-static struct platform_device roadrunner_flash = {
- .name = "physmap-flash",
- .id = 0,
- .dev = {
- .platform_data = &roadrunner_flash_data,
- },
- .num_resources = 1,
- .resource = &roadrunner_flash_resource,
-};
-
-static void __init roadrunner_init(void)
-{
- platform_device_register(&roadrunner_flash);
-
- /*
- * Mark flash as writeable
- */
- IXP23XX_EXP_CS0[0] |= IXP23XX_FLASH_WRITABLE;
- IXP23XX_EXP_CS0[1] |= IXP23XX_FLASH_WRITABLE;
- IXP23XX_EXP_CS0[2] |= IXP23XX_FLASH_WRITABLE;
- IXP23XX_EXP_CS0[3] |= IXP23XX_FLASH_WRITABLE;
-
- ixp23xx_sys_init();
-}
-
-MACHINE_START(ROADRUNNER, "ADI Engineering RoadRunner Development Platform")
- /* Maintainer: Deepak Saxena */
- .map_io = ixp23xx_map_io,
- .init_irq = ixp23xx_init_irq,
- .timer = &ixp23xx_timer,
- .atag_offset = 0x100,
- .init_machine = roadrunner_init,
- .restart = ixp23xx_restart,
-MACHINE_END
projects / profile / ivi / kernel-adaptation-intel-automotive.git / commitdiff