return 0;
while (retry_count < 2) {
- ret_val = e1e_rphy(hw, PHY_ID1, &phy_id);
+ ret_val = e1e_rphy(hw, MII_PHYSID1, &phy_id);
if (ret_val)
return ret_val;
phy->id = (u32)(phy_id << 16);
udelay(20);
- ret_val = e1e_rphy(hw, PHY_ID2, &phy_id);
+ ret_val = e1e_rphy(hw, MII_PHYSID2, &phy_id);
if (ret_val)
return ret_val;
u16 phy_data;
/* Resolve Master/Slave mode */
- ret_val = e1e_rphy(hw, PHY_1000T_CTRL, &phy_data);
+ ret_val = e1e_rphy(hw, MII_CTRL1000, &phy_data);
if (ret_val)
return ret_val;
/* load defaults for future use */
- hw->phy.original_ms_type = (phy_data & CR_1000T_MS_ENABLE) ?
- ((phy_data & CR_1000T_MS_VALUE) ?
+ hw->phy.original_ms_type = (phy_data & CTL1000_ENABLE_MASTER) ?
+ ((phy_data & CTL1000_AS_MASTER) ?
e1000_ms_force_master : e1000_ms_force_slave) : e1000_ms_auto;
switch (hw->phy.ms_type) {
case e1000_ms_force_master:
- phy_data |= (CR_1000T_MS_ENABLE | CR_1000T_MS_VALUE);
+ phy_data |= (CTL1000_ENABLE_MASTER | CTL1000_AS_MASTER);
break;
case e1000_ms_force_slave:
- phy_data |= CR_1000T_MS_ENABLE;
- phy_data &= ~(CR_1000T_MS_VALUE);
+ phy_data |= CTL1000_ENABLE_MASTER;
+ phy_data &= ~(CTL1000_AS_MASTER);
break;
case e1000_ms_auto:
- phy_data &= ~CR_1000T_MS_ENABLE;
+ phy_data &= ~CTL1000_ENABLE_MASTER;
/* fall-through */
default:
break;
}
- return e1e_wphy(hw, PHY_1000T_CTRL, phy_data);
+ return e1e_wphy(hw, MII_CTRL1000, phy_data);
}
/**
return ret_val;
/* Set auto Master/Slave resolution process */
- ret_val = e1e_rphy(hw, PHY_1000T_CTRL, &data);
+ ret_val = e1e_rphy(hw, MII_CTRL1000, &data);
if (ret_val)
return ret_val;
- data &= ~CR_1000T_MS_ENABLE;
- ret_val = e1e_wphy(hw, PHY_1000T_CTRL, data);
+ data &= ~CTL1000_ENABLE_MASTER;
+ ret_val = e1e_wphy(hw, MII_CTRL1000, data);
if (ret_val)
return ret_val;
}
phy->autoneg_advertised &= phy->autoneg_mask;
/* Read the MII Auto-Neg Advertisement Register (Address 4). */
- ret_val = e1e_rphy(hw, PHY_AUTONEG_ADV, &mii_autoneg_adv_reg);
+ ret_val = e1e_rphy(hw, MII_ADVERTISE, &mii_autoneg_adv_reg);
if (ret_val)
return ret_val;
if (phy->autoneg_mask & ADVERTISE_1000_FULL) {
/* Read the MII 1000Base-T Control Register (Address 9). */
- ret_val = e1e_rphy(hw, PHY_1000T_CTRL, &mii_1000t_ctrl_reg);
+ ret_val = e1e_rphy(hw, MII_CTRL1000, &mii_1000t_ctrl_reg);
if (ret_val)
return ret_val;
}
* Advertisement Register (Address 4) and the 1000 mb speed bits in
* the 1000Base-T Control Register (Address 9).
*/
- mii_autoneg_adv_reg &= ~(NWAY_AR_100TX_FD_CAPS |
- NWAY_AR_100TX_HD_CAPS |
- NWAY_AR_10T_FD_CAPS |
- NWAY_AR_10T_HD_CAPS);
- mii_1000t_ctrl_reg &= ~(CR_1000T_HD_CAPS | CR_1000T_FD_CAPS);
+ mii_autoneg_adv_reg &= ~(ADVERTISE_100FULL |
+ ADVERTISE_100HALF |
+ ADVERTISE_10FULL | ADVERTISE_10HALF);
+ mii_1000t_ctrl_reg &= ~(ADVERTISE_1000HALF | ADVERTISE_1000FULL);
e_dbg("autoneg_advertised %x\n", phy->autoneg_advertised);
/* Do we want to advertise 10 Mb Half Duplex? */
if (phy->autoneg_advertised & ADVERTISE_10_HALF) {
e_dbg("Advertise 10mb Half duplex\n");
- mii_autoneg_adv_reg |= NWAY_AR_10T_HD_CAPS;
+ mii_autoneg_adv_reg |= ADVERTISE_10HALF;
}
/* Do we want to advertise 10 Mb Full Duplex? */
if (phy->autoneg_advertised & ADVERTISE_10_FULL) {
e_dbg("Advertise 10mb Full duplex\n");
- mii_autoneg_adv_reg |= NWAY_AR_10T_FD_CAPS;
+ mii_autoneg_adv_reg |= ADVERTISE_10FULL;
}
/* Do we want to advertise 100 Mb Half Duplex? */
if (phy->autoneg_advertised & ADVERTISE_100_HALF) {
e_dbg("Advertise 100mb Half duplex\n");
- mii_autoneg_adv_reg |= NWAY_AR_100TX_HD_CAPS;
+ mii_autoneg_adv_reg |= ADVERTISE_100HALF;
}
/* Do we want to advertise 100 Mb Full Duplex? */
if (phy->autoneg_advertised & ADVERTISE_100_FULL) {
e_dbg("Advertise 100mb Full duplex\n");
- mii_autoneg_adv_reg |= NWAY_AR_100TX_FD_CAPS;
+ mii_autoneg_adv_reg |= ADVERTISE_100FULL;
}
/* We do not allow the Phy to advertise 1000 Mb Half Duplex */
/* Do we want to advertise 1000 Mb Full Duplex? */
if (phy->autoneg_advertised & ADVERTISE_1000_FULL) {
e_dbg("Advertise 1000mb Full duplex\n");
- mii_1000t_ctrl_reg |= CR_1000T_FD_CAPS;
+ mii_1000t_ctrl_reg |= ADVERTISE_1000FULL;
}
/* Check for a software override of the flow control settings, and
* setup the PHY advertisement registers accordingly. If
* auto-negotiation is enabled, then software will have to set the
* "PAUSE" bits to the correct value in the Auto-Negotiation
- * Advertisement Register (PHY_AUTONEG_ADV) and re-start auto-
+ * Advertisement Register (MII_ADVERTISE) and re-start auto-
* negotiation.
*
* The possible values of the "fc" parameter are:
/* Flow control (Rx & Tx) is completely disabled by a
* software over-ride.
*/
- mii_autoneg_adv_reg &= ~(NWAY_AR_ASM_DIR | NWAY_AR_PAUSE);
+ mii_autoneg_adv_reg &=
+ ~(ADVERTISE_PAUSE_ASYM | ADVERTISE_PAUSE_CAP);
break;
case e1000_fc_rx_pause:
/* Rx Flow control is enabled, and Tx Flow control is
* (in e1000e_config_fc_after_link_up) we will disable the
* hw's ability to send PAUSE frames.
*/
- mii_autoneg_adv_reg |= (NWAY_AR_ASM_DIR | NWAY_AR_PAUSE);
+ mii_autoneg_adv_reg |=
+ (ADVERTISE_PAUSE_ASYM | ADVERTISE_PAUSE_CAP);
break;
case e1000_fc_tx_pause:
/* Tx Flow control is enabled, and Rx Flow control is
* disabled, by a software over-ride.
*/
- mii_autoneg_adv_reg |= NWAY_AR_ASM_DIR;
- mii_autoneg_adv_reg &= ~NWAY_AR_PAUSE;
+ mii_autoneg_adv_reg |= ADVERTISE_PAUSE_ASYM;
+ mii_autoneg_adv_reg &= ~ADVERTISE_PAUSE_CAP;
break;
case e1000_fc_full:
/* Flow control (both Rx and Tx) is enabled by a software
* over-ride.
*/
- mii_autoneg_adv_reg |= (NWAY_AR_ASM_DIR | NWAY_AR_PAUSE);
+ mii_autoneg_adv_reg |=
+ (ADVERTISE_PAUSE_ASYM | ADVERTISE_PAUSE_CAP);
break;
default:
e_dbg("Flow control param set incorrectly\n");
return -E1000_ERR_CONFIG;
}
- ret_val = e1e_wphy(hw, PHY_AUTONEG_ADV, mii_autoneg_adv_reg);
+ ret_val = e1e_wphy(hw, MII_ADVERTISE, mii_autoneg_adv_reg);
if (ret_val)
return ret_val;
e_dbg("Auto-Neg Advertising %x\n", mii_autoneg_adv_reg);
if (phy->autoneg_mask & ADVERTISE_1000_FULL)
- ret_val = e1e_wphy(hw, PHY_1000T_CTRL, mii_1000t_ctrl_reg);
+ ret_val = e1e_wphy(hw, MII_CTRL1000, mii_1000t_ctrl_reg);
return ret_val;
}
/* Restart auto-negotiation by setting the Auto Neg Enable bit and
* the Auto Neg Restart bit in the PHY control register.
*/
- ret_val = e1e_rphy(hw, PHY_CONTROL, &phy_ctrl);
+ ret_val = e1e_rphy(hw, MII_BMCR, &phy_ctrl);
if (ret_val)
return ret_val;
- phy_ctrl |= (MII_CR_AUTO_NEG_EN | MII_CR_RESTART_AUTO_NEG);
- ret_val = e1e_wphy(hw, PHY_CONTROL, phy_ctrl);
+ phy_ctrl |= (BMCR_ANENABLE | BMCR_ANRESTART);
+ ret_val = e1e_wphy(hw, MII_BMCR, phy_ctrl);
if (ret_val)
return ret_val;
u16 phy_data;
bool link;
- ret_val = e1e_rphy(hw, PHY_CONTROL, &phy_data);
+ ret_val = e1e_rphy(hw, MII_BMCR, &phy_data);
if (ret_val)
return ret_val;
e1000e_phy_force_speed_duplex_setup(hw, &phy_data);
- ret_val = e1e_wphy(hw, PHY_CONTROL, phy_data);
+ ret_val = e1e_wphy(hw, MII_BMCR, phy_data);
if (ret_val)
return ret_val;
e_dbg("M88E1000 PSCR: %X\n", phy_data);
- ret_val = e1e_rphy(hw, PHY_CONTROL, &phy_data);
+ ret_val = e1e_rphy(hw, MII_BMCR, &phy_data);
if (ret_val)
return ret_val;
e1000e_phy_force_speed_duplex_setup(hw, &phy_data);
- ret_val = e1e_wphy(hw, PHY_CONTROL, phy_data);
+ ret_val = e1e_wphy(hw, MII_BMCR, phy_data);
if (ret_val)
return ret_val;
u16 data;
bool link;
- ret_val = e1e_rphy(hw, PHY_CONTROL, &data);
+ ret_val = e1e_rphy(hw, MII_BMCR, &data);
if (ret_val)
return ret_val;
e1000e_phy_force_speed_duplex_setup(hw, &data);
- ret_val = e1e_wphy(hw, PHY_CONTROL, data);
+ ret_val = e1e_wphy(hw, MII_BMCR, data);
if (ret_val)
return ret_val;
/**
* e1000e_phy_force_speed_duplex_setup - Configure forced PHY speed/duplex
* @hw: pointer to the HW structure
- * @phy_ctrl: pointer to current value of PHY_CONTROL
+ * @phy_ctrl: pointer to current value of MII_BMCR
*
* Forces speed and duplex on the PHY by doing the following: disable flow
* control, force speed/duplex on the MAC, disable auto speed detection,
* disable auto-negotiation, configure duplex, configure speed, configure
* the collision distance, write configuration to CTRL register. The
- * caller must write to the PHY_CONTROL register for these settings to
+ * caller must write to the MII_BMCR register for these settings to
* take affect.
**/
void e1000e_phy_force_speed_duplex_setup(struct e1000_hw *hw, u16 *phy_ctrl)
ctrl &= ~E1000_CTRL_ASDE;
/* Disable autoneg on the phy */
- *phy_ctrl &= ~MII_CR_AUTO_NEG_EN;
+ *phy_ctrl &= ~BMCR_ANENABLE;
/* Forcing Full or Half Duplex? */
if (mac->forced_speed_duplex & E1000_ALL_HALF_DUPLEX) {
ctrl &= ~E1000_CTRL_FD;
- *phy_ctrl &= ~MII_CR_FULL_DUPLEX;
+ *phy_ctrl &= ~BMCR_FULLDPLX;
e_dbg("Half Duplex\n");
} else {
ctrl |= E1000_CTRL_FD;
- *phy_ctrl |= MII_CR_FULL_DUPLEX;
+ *phy_ctrl |= BMCR_FULLDPLX;
e_dbg("Full Duplex\n");
}
/* Forcing 10mb or 100mb? */
if (mac->forced_speed_duplex & E1000_ALL_100_SPEED) {
ctrl |= E1000_CTRL_SPD_100;
- *phy_ctrl |= MII_CR_SPEED_100;
- *phy_ctrl &= ~(MII_CR_SPEED_1000 | MII_CR_SPEED_10);
+ *phy_ctrl |= BMCR_SPEED100;
+ *phy_ctrl &= ~BMCR_SPEED1000;
e_dbg("Forcing 100mb\n");
} else {
ctrl &= ~(E1000_CTRL_SPD_1000 | E1000_CTRL_SPD_100);
- *phy_ctrl |= MII_CR_SPEED_10;
- *phy_ctrl &= ~(MII_CR_SPEED_1000 | MII_CR_SPEED_100);
+ *phy_ctrl &= ~(BMCR_SPEED1000 | BMCR_SPEED100);
e_dbg("Forcing 10mb\n");
}
/* Break after autoneg completes or PHY_AUTO_NEG_LIMIT expires. */
for (i = PHY_AUTO_NEG_LIMIT; i > 0; i--) {
- ret_val = e1e_rphy(hw, PHY_STATUS, &phy_status);
+ ret_val = e1e_rphy(hw, MII_BMSR, &phy_status);
if (ret_val)
break;
- ret_val = e1e_rphy(hw, PHY_STATUS, &phy_status);
+ ret_val = e1e_rphy(hw, MII_BMSR, &phy_status);
if (ret_val)
break;
- if (phy_status & MII_SR_AUTONEG_COMPLETE)
+ if (phy_status & BMSR_ANEGCOMPLETE)
break;
msleep(100);
}
u16 i, phy_status;
for (i = 0; i < iterations; i++) {
- /* Some PHYs require the PHY_STATUS register to be read
+ /* Some PHYs require the MII_BMSR register to be read
* twice due to the link bit being sticky. No harm doing
* it across the board.
*/
- ret_val = e1e_rphy(hw, PHY_STATUS, &phy_status);
+ ret_val = e1e_rphy(hw, MII_BMSR, &phy_status);
if (ret_val)
/* If the first read fails, another entity may have
* ownership of the resources, wait and try again to
* see if they have relinquished the resources yet.
*/
udelay(usec_interval);
- ret_val = e1e_rphy(hw, PHY_STATUS, &phy_status);
+ ret_val = e1e_rphy(hw, MII_BMSR, &phy_status);
if (ret_val)
break;
- if (phy_status & MII_SR_LINK_STATUS)
+ if (phy_status & BMSR_LSTATUS)
break;
if (usec_interval >= 1000)
mdelay(usec_interval/1000);
if (ret_val)
return ret_val;
- ret_val = e1e_rphy(hw, PHY_1000T_STATUS, &phy_data);
+ ret_val = e1e_rphy(hw, MII_STAT1000, &phy_data);
if (ret_val)
return ret_val;
- phy->local_rx = (phy_data & SR_1000T_LOCAL_RX_STATUS)
- ? e1000_1000t_rx_status_ok
- : e1000_1000t_rx_status_not_ok;
+ phy->local_rx = (phy_data & LPA_1000LOCALRXOK)
+ ? e1000_1000t_rx_status_ok : e1000_1000t_rx_status_not_ok;
- phy->remote_rx = (phy_data & SR_1000T_REMOTE_RX_STATUS)
- ? e1000_1000t_rx_status_ok
- : e1000_1000t_rx_status_not_ok;
+ phy->remote_rx = (phy_data & LPA_1000REMRXOK)
+ ? e1000_1000t_rx_status_ok : e1000_1000t_rx_status_not_ok;
} else {
/* Set values to "undefined" */
phy->cable_length = E1000_CABLE_LENGTH_UNDEFINED;
if (ret_val)
return ret_val;
- ret_val = e1e_rphy(hw, PHY_1000T_STATUS, &data);
+ ret_val = e1e_rphy(hw, MII_STAT1000, &data);
if (ret_val)
return ret_val;
- phy->local_rx = (data & SR_1000T_LOCAL_RX_STATUS)
- ? e1000_1000t_rx_status_ok
- : e1000_1000t_rx_status_not_ok;
+ phy->local_rx = (data & LPA_1000LOCALRXOK)
+ ? e1000_1000t_rx_status_ok : e1000_1000t_rx_status_not_ok;
- phy->remote_rx = (data & SR_1000T_REMOTE_RX_STATUS)
- ? e1000_1000t_rx_status_ok
- : e1000_1000t_rx_status_not_ok;
+ phy->remote_rx = (data & LPA_1000REMRXOK)
+ ? e1000_1000t_rx_status_ok : e1000_1000t_rx_status_not_ok;
} else {
phy->cable_length = E1000_CABLE_LENGTH_UNDEFINED;
phy->local_rx = e1000_1000t_rx_status_undefined;
s32 ret_val;
u16 phy_ctrl;
- ret_val = e1e_rphy(hw, PHY_CONTROL, &phy_ctrl);
+ ret_val = e1e_rphy(hw, MII_BMCR, &phy_ctrl);
if (ret_val)
return ret_val;
- phy_ctrl |= MII_CR_RESET;
- ret_val = e1e_wphy(hw, PHY_CONTROL, phy_ctrl);
+ phy_ctrl |= BMCR_RESET;
+ ret_val = e1e_wphy(hw, MII_BMCR, phy_ctrl);
if (ret_val)
return ret_val;
u16 mii_reg = 0;
/* The PHY will retain its settings across a power down/up cycle */
- e1e_rphy(hw, PHY_CONTROL, &mii_reg);
- mii_reg &= ~MII_CR_POWER_DOWN;
- e1e_wphy(hw, PHY_CONTROL, mii_reg);
+ e1e_rphy(hw, MII_BMCR, &mii_reg);
+ mii_reg &= ~BMCR_PDOWN;
+ e1e_wphy(hw, MII_BMCR, mii_reg);
}
/**
u16 mii_reg = 0;
/* The PHY will retain its settings across a power down/up cycle */
- e1e_rphy(hw, PHY_CONTROL, &mii_reg);
- mii_reg |= MII_CR_POWER_DOWN;
- e1e_wphy(hw, PHY_CONTROL, mii_reg);
+ e1e_rphy(hw, MII_BMCR, &mii_reg);
+ mii_reg |= BMCR_PDOWN;
+ e1e_wphy(hw, MII_BMCR, mii_reg);
usleep_range(1000, 2000);
}
return 0;
/* Do not apply workaround if in PHY loopback bit 14 set */
- e1e_rphy(hw, PHY_CONTROL, &data);
- if (data & PHY_CONTROL_LB)
+ e1e_rphy(hw, MII_BMCR, &data);
+ if (data & BMCR_LOOPBACK)
return 0;
/* check if link is up and at 1Gbps */
u16 phy_data;
bool link;
- ret_val = e1e_rphy(hw, PHY_CONTROL, &phy_data);
+ ret_val = e1e_rphy(hw, MII_BMCR, &phy_data);
if (ret_val)
return ret_val;
e1000e_phy_force_speed_duplex_setup(hw, &phy_data);
- ret_val = e1e_wphy(hw, PHY_CONTROL, phy_data);
+ ret_val = e1e_wphy(hw, MII_BMCR, phy_data);
if (ret_val)
return ret_val;
if (ret_val)
return ret_val;
- ret_val = e1e_rphy(hw, PHY_1000T_STATUS, &data);
+ ret_val = e1e_rphy(hw, MII_STAT1000, &data);
if (ret_val)
return ret_val;
- phy->local_rx = (data & SR_1000T_LOCAL_RX_STATUS)
- ? e1000_1000t_rx_status_ok
- : e1000_1000t_rx_status_not_ok;
+ phy->local_rx = (data & LPA_1000LOCALRXOK)
+ ? e1000_1000t_rx_status_ok : e1000_1000t_rx_status_not_ok;
- phy->remote_rx = (data & SR_1000T_REMOTE_RX_STATUS)
- ? e1000_1000t_rx_status_ok
- : e1000_1000t_rx_status_not_ok;
+ phy->remote_rx = (data & LPA_1000REMRXOK)
+ ? e1000_1000t_rx_status_ok : e1000_1000t_rx_status_not_ok;
} else {
phy->cable_length = E1000_CABLE_LENGTH_UNDEFINED;
phy->local_rx = e1000_1000t_rx_status_undefined;
projects / platform / kernel / linux-starfive.git / commitdiff