ide: move CONFIG_IDE_ETRAX to drivers/ide/Kconfig

* Move ETRAX_IDE and friends from arch/cris/arch-{v10,v32}/drivers/Kconfig
  to drivers/ide/Kconfig.

* Don't force selecting ide-disk and ide-cd device drivers
  (please handle this through defconfig if necessary).

* Make ETRAX_IDE depend on BROKEN for the time being
  (it doesn't even compile currently).

Cc: Mikael Starvik <starvik@axis.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

diff --git a/arch/cris/arch-v10/drivers/Kconfig b/arch/cris/arch-v10/drivers/Kconfig
index faf8b4d..e3c0f29 100644 (file)
--- a/arch/cris/arch-v10/drivers/Kconfig
+++ b/arch/cris/arch-v10/drivers/Kconfig
@@ -542,45 +542,6 @@ config ETRAX_RS485_DISABLE_RECEIVER
          loopback.  Not all products are able to do this in software only.
          Axis 2400/2401 must disable receiver.
 
-config ETRAX_IDE
-       bool "ATA/IDE support"
-       select IDE
-       select BLK_DEV_IDE
-       select BLK_DEV_IDEDISK
-       select BLK_DEV_IDECD
-       select BLK_DEV_IDEDMA
-       select IDE_GENERIC
-       help
-         Enable this to get support for ATA/IDE.
-         You can't use parallel ports or SCSI ports
-         at the same time.
-
-
-config ETRAX_IDE_DELAY
-       int "Delay for drives to regain consciousness"
-       depends on ETRAX_IDE
-       default 15
-       help
-         Number of seconds to wait for IDE drives to spin up after an IDE
-         reset.
-choice
-       prompt "IDE reset pin"
-       depends on ETRAX_IDE
-       default ETRAX_IDE_PB7_RESET
-
-config ETRAX_IDE_PB7_RESET
-       bool "Port_PB_Bit_7"
-       help
-         IDE reset on pin 7 on port B
-
-config ETRAX_IDE_G27_RESET
-       bool "Port_G_Bit_27"
-       help
-         IDE reset on pin 27 on port G
-
-endchoice
-
-
 config ETRAX_USB_HOST
        bool "USB host"
        select USB

diff --git a/arch/cris/arch-v32/drivers/Kconfig b/arch/cris/arch-v32/drivers/Kconfig
index 7f72d7c..9bccb5e 100644 (file)
--- a/arch/cris/arch-v32/drivers/Kconfig
+++ b/arch/cris/arch-v32/drivers/Kconfig
@@ -582,18 +582,6 @@ config ETRAX_PE_CHANGEABLE_BITS
          that a user can change the value on using ioctl's.
          Bit set = changeable.
 
-config ETRAX_IDE
-       bool "ATA/IDE support"
-       depends on ETRAX_ARCH_V32
-       select IDE
-       select BLK_DEV_IDE
-       select BLK_DEV_IDEDISK
-       select BLK_DEV_IDECD
-       select BLK_DEV_IDEDMA
-       select IDE_GENERIC
-       help
-         Enables the ETRAX IDE driver.
-
 config ETRAX_CARDBUS
         bool "Cardbus support"
         depends on ETRAX_ARCH_V32

diff --git a/drivers/ide/Kconfig b/drivers/ide/Kconfig
index ca8239a..403e3ff 100644 (file)
--- a/drivers/ide/Kconfig
+++ b/drivers/ide/Kconfig
@@ -882,6 +882,41 @@ config BLK_DEV_IDE_BAST
          Say Y here if you want to support the onboard IDE channels on the
          Simtec BAST or the Thorcom VR1000
 
+config ETRAX_IDE
+       bool "ETRAX IDE support"
+       depends on CRIS && BROKEN
+       select BLK_DEV_IDEDMA
+       select IDE_GENERIC
+       help
+         Enables the ETRAX IDE driver.
+
+         You can't use parallel ports or SCSI ports at the same time.
+
+config ETRAX_IDE_DELAY
+       int "Delay for drives to regain consciousness"
+       depends on ETRAX_IDE && ETRAX_ARCH_V10
+       default 15
+       help
+         Number of seconds to wait for IDE drives to spin up after an IDE
+         reset.
+
+choice
+       prompt "IDE reset pin"
+       depends on ETRAX_IDE && ETRAX_ARCH_V10
+       default ETRAX_IDE_PB7_RESET
+
+config ETRAX_IDE_PB7_RESET
+       bool "Port_PB_Bit_7"
+       help
+         IDE reset on pin 7 on port B
+
+config ETRAX_IDE_G27_RESET
+       bool "Port_G_Bit_27"
+       help
+         IDE reset on pin 27 on port G
+
+endchoice
+
 config IDE_H8300
        bool "H8300 IDE support"
        depends on H8300