xilinx: zynqmp: Add support for runtime dfu_alt_info setup

The main reason for this to be implemented is capsule update.
Two memories are supported and tested which is MMC FAT based and QSPI
based.

For creating capsule these commands are used:
./tools/mkeficapsule --raw spl/boot.bin --index 1 capsule1.bin
./tools/mkeficapsule --raw u-boot.itb --index 2 capsule2.bin

Then transfer to SD card where these commands run:
load mmc 0 10000000 capsule1.bin
efidebug capsule update -v 10000000
load mmc 0 10000000 capsule2.bin
efidebug capsule update -v 10000000

Depends on the boot device used are binaries loaded to qspi or mmc fat
partition.
Also multiboot register is handled to make sure that the same location(id)
is used as image which is upgraded.

Two locations are used by purpose for SPL flow. If only boot.bin is used
create only one capsule.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

diff --git a/board/xilinx/zynqmp/zynqmp.c b/board/xilinx/zynqmp/zynqmp.c
index 1b0356c..27bb2b0 100644 (file)
--- a/board/xilinx/zynqmp/zynqmp.c
+++ b/board/xilinx/zynqmp/zynqmp.c
@@ -8,6 +8,7 @@
 #include <command.h>
 #include <cpu_func.h>
 #include <debug_uart.h>
+#include <dfu.h>
 #include <env.h>
 #include <env_internal.h>
 #include <init.h>
@@ -19,6 +20,7 @@
 #include <ahci.h>
 #include <scsi.h>
 #include <malloc.h>
+#include <memalign.h>
 #include <wdt.h>
 #include <asm/arch/clk.h>
 #include <asm/arch/hardware.h>
@@ -818,3 +820,55 @@ enum env_location env_get_location(enum env_operation op, int prio)
                return ENVL_NOWHERE;
        }
 }
+
+#if defined(CONFIG_SET_DFU_ALT_INFO)
+
+#define DFU_ALT_BUF_LEN                SZ_1K
+
+void set_dfu_alt_info(char *interface, char *devstr)
+{
+       u8 multiboot;
+       int bootseq = 0;
+
+       ALLOC_CACHE_ALIGN_BUFFER(char, buf, DFU_ALT_BUF_LEN);
+
+       if (env_get("dfu_alt_info"))
+               return;
+
+       memset(buf, 0, sizeof(buf));
+
+       multiboot = multi_boot();
+       debug("Multiboot: %d\n", multiboot);
+
+       switch (zynqmp_get_bootmode()) {
+       case EMMC_MODE:
+       case SD_MODE:
+       case SD1_LSHFT_MODE:
+       case SD_MODE1:
+               bootseq = mmc_get_env_dev();
+               if (!multiboot)
+                       snprintf(buf, DFU_ALT_BUF_LEN,
+                                "mmc %d:1=boot.bin fat %d 1;"
+                                "u-boot.itb fat %d 1",
+                                bootseq, bootseq, bootseq);
+               else
+                       snprintf(buf, DFU_ALT_BUF_LEN,
+                                "mmc %d:1=boot%04d.bin fat %d 1;"
+                                "u-boot.itb fat %d 1",
+                                bootseq, multiboot, bootseq, bootseq);
+               break;
+       case QSPI_MODE_24BIT:
+       case QSPI_MODE_32BIT:
+               snprintf(buf, DFU_ALT_BUF_LEN,
+                        "sf 0:0=boot.bin raw %x 0x1500000;"
+                        "u-boot.itb raw 0x%x 0x500000",
+                        multiboot * SZ_32K, CONFIG_SYS_SPI_U_BOOT_OFFS);
+               break;
+       default:
+               return;
+       }
+
+       env_set("dfu_alt_info", buf);
+       puts("DFU alt info setting: done\n");
+}
+#endif

diff --git a/configs/xilinx_zynqmp_virt_defconfig b/configs/xilinx_zynqmp_virt_defconfig
index 73972a0..40a87ca 100644 (file)
--- a/configs/xilinx_zynqmp_virt_defconfig
+++ b/configs/xilinx_zynqmp_virt_defconfig
@@ -94,6 +94,7 @@ CONFIG_DFU_NAND=y
 CONFIG_DFU_RAM=y
 CONFIG_DFU_SF=y
 CONFIG_DFU_MTD=y
+CONFIG_SET_DFU_ALT_INFO=y
 CONFIG_SYS_DFU_DATA_BUF_SIZE=0x1800000
 CONFIG_USB_FUNCTION_FASTBOOT=y
 CONFIG_FASTBOOT_FLASH=y