ifneq ($(CONFIG_LS1043A),)
obj-$(CONFIG_SYS_HAS_SERDES) += ls1043a_serdes.o
endif
+
+ifneq ($(CONFIG_LS1012A),)
+obj-$(CONFIG_SYS_HAS_SERDES) += ls1012a_serdes.o
+endif
1. LS1043A
2. LS2080A
+ 3. LS1012A
LS1043A
---------
- QorIQ platform's trust architecture 3.0
- Service processor (SP) provides pre-boot initialization and secure-boot
capabilities
+
+LS1012A
+--------
+The LS1012A features an advanced 64-bit ARM v8 Cortex-
+A53 processor, with 32 KB of parity protected L1-I cache,
+32 KB of ECC protected L1-D cache, as well as 256 KB of
+ECC protected L2 cache.
+
+The LS1012A SoC includes the following function and features:
+ - One 64-bit ARM v8 Cortex-A53 core with the following capabilities:
+ - ARM v8 cryptography extensions
+ - One 16-bit DDR3L SDRAM memory controller, Up to 1.0 GT/s, Supports
+ 16-/8-bit operation (no ECC support)
+ - ARM core-link CCI-400 cache coherent interconnect
+ - Packet Forwarding Engine (PFE)
+ - Cryptography acceleration (SEC)
+ - Ethernet interfaces supported by PFE:
+ - One Configurable x3 SerDes:
+ Two Serdes PLLs supported for usage by any SerDes data lane
+ Support for up to 6 GBaud operation
+ - High-speed peripheral interfaces:
+ - One PCI Express Gen2 controller, supporting x1 operation
+ - One serial ATA (SATA Gen 3.0) controller
+ - One USB 3.0/2.0 controller with integrated PHY
+ - One USB 2.0 controller with ULPI interface. .
+ - Additional peripheral interfaces:
+ - One quad serial peripheral interface (QuadSPI) controller
+ - One serial peripheral interface (SPI) controller
+ - Two enhanced secure digital host controllers
+ - Two I2C controllers
+ - One 16550 compliant DUART (two UART interfaces)
+ - Two general purpose IOs (GPIO)
+ - Two FlexTimers
+ - Five synchronous audio interfaces (SAI)
+ - Pre-boot loader (PBL) provides pre-boot initialization and RCW loading
+ - Single-source clocking solution enabling generation of core, platform,
+ DDR, SerDes, and USB clocks from a single external crystal and internal
+ crystaloscillator
+ - Thermal monitor unit (TMU) with +/- 3C accuracy
+ - Two WatchDog timers
+ - ARM generic timer
+ - QorIQ platform's trust architecture 2.1
sys_info->freq_ddrbus = sysclk;
#endif
+#ifdef CONFIG_LS1012A
+ sys_info->freq_ddrbus *= (gur_in32(&gur->rcwsr[0]) >>
+ FSL_CHASSIS2_RCWSR0_SYS_PLL_RAT_SHIFT) &
+ FSL_CHASSIS2_RCWSR0_SYS_PLL_RAT_MASK;
+#else
sys_info->freq_systembus *= (gur_in32(&gur->rcwsr[0]) >>
FSL_CHASSIS2_RCWSR0_SYS_PLL_RAT_SHIFT) &
FSL_CHASSIS2_RCWSR0_SYS_PLL_RAT_MASK;
sys_info->freq_ddrbus *= (gur_in32(&gur->rcwsr[0]) >>
FSL_CHASSIS2_RCWSR0_MEM_PLL_RAT_SHIFT) &
FSL_CHASSIS2_RCWSR0_MEM_PLL_RAT_MASK;
+#endif
for (i = 0; i < CONFIG_SYS_FSL_NUM_CC_PLLS; i++) {
ratio[i] = (in_be32(&clk->pllcgsr[i].pllcngsr) >> 1) & 0xff;
freq_c_pll[cplx_pll] / core_cplx_pll_div[c_pll_sel];
}
+#ifdef CONFIG_LS1012A
+ sys_info->freq_systembus = sys_info->freq_ddrbus / 2;
+ sys_info->freq_ddrbus *= 2;
+#endif
+
#define HWA_CGA_M1_CLK_SEL 0xe0000000
#define HWA_CGA_M1_CLK_SHIFT 29
#ifdef CONFIG_SYS_DPAA_FMAN
ret
ENDPROC(lowlevel_init)
+#ifdef CONFIG_FSL_LSCH3
hnf_pstate_poll:
/* x0 has the desired status, return 0 for success, 1 for timeout
* clobber x1, x2, x3, x4, x6, x7
mov lr, x29
ret
ENDPROC(__asm_flush_l3_cache)
+#endif
#ifdef CONFIG_MP
/* Keep literals not used by the secondary boot code outside it */
--- /dev/null
+/*
+ * Copyright 2016 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/arch/fsl_serdes.h>
+#include <asm/arch/immap_lsch2.h>
+
+struct serdes_config {
+ u32 protocol;
+ u8 lanes[SRDS_MAX_LANES];
+};
+
+static struct serdes_config serdes1_cfg_tbl[] = {
+ {0x2208, {SGMII_2500_FM1_DTSEC1, SGMII_2500_FM1_DTSEC2, NONE, SATA1} },
+ {0x0008, {NONE, NONE, NONE, SATA1} },
+ {0x3508, {SGMII_FM1_DTSEC1, PCIE1, NONE, SATA1} },
+ {0x3305, {SGMII_FM1_DTSEC1, SGMII_FM1_DTSEC2, NONE, PCIE1} },
+ {0x2205, {SGMII_2500_FM1_DTSEC1, SGMII_2500_FM1_DTSEC2, NONE, PCIE1} },
+ {0x2305, {SGMII_2500_FM1_DTSEC1, SGMII_FM1_DTSEC2, NONE, PCIE1} },
+ {0x9508, {TX_CLK, PCIE1, NONE, SATA1} },
+ {0x3905, {SGMII_FM1_DTSEC1, TX_CLK, NONE, PCIE1} },
+ {0x9305, {TX_CLK, SGMII_FM1_DTSEC2, NONE, PCIE1} },
+ {}
+};
+
+static struct serdes_config *serdes_cfg_tbl[] = {
+ serdes1_cfg_tbl,
+};
+
+enum srds_prtcl serdes_get_prtcl(int serdes, int cfg, int lane)
+{
+ struct serdes_config *ptr;
+
+ if (serdes >= ARRAY_SIZE(serdes_cfg_tbl))
+ return 0;
+
+ ptr = serdes_cfg_tbl[serdes];
+ while (ptr->protocol) {
+ if (ptr->protocol == cfg)
+ return ptr->lanes[lane];
+ ptr++;
+ }
+
+ return 0;
+}
+
+int is_serdes_prtcl_valid(int serdes, u32 prtcl)
+{
+ int i;
+ struct serdes_config *ptr;
+
+ if (serdes >= ARRAY_SIZE(serdes_cfg_tbl))
+ return 0;
+
+ ptr = serdes_cfg_tbl[serdes];
+ while (ptr->protocol) {
+ if (ptr->protocol == prtcl)
+ break;
+ ptr++;
+ }
+
+ if (!ptr->protocol)
+ return 0;
+
+ for (i = 0; i < SRDS_MAX_LANES; i++) {
+ if (ptr->lanes[i] != NONE)
+ return 1;
+ }
+
+ return 0;
+}
#include <asm/io.h>
#include <asm/global_data.h>
#include <asm/arch-fsl-layerscape/config.h>
+#ifdef CONFIG_SYS_FSL_DDR
#include <fsl_ddr_sdram.h>
#include <fsl_ddr.h>
+#endif
#ifdef CONFIG_CHAIN_OF_TRUST
#include <fsl_validate.h>
#endif
#else
#define CONFIG_SYS_FSL_DDRC_ARM_GEN3 /* Enable Freescale ARM DDR3 driver */
#endif
+
+#ifndef CONFIG_LS1012A
#define CONFIG_SYS_FSL_DDR /* Freescale DDR driver */
#define CONFIG_SYS_FSL_DDR_VER FSL_DDR_VER_5_0
+#endif
/*
* Reserve secure memory
#define CONFIG_SYS_FSL_ERRATUM_A009942
#define CONFIG_SYS_FSL_ERRATUM_A009660
#define CONFIG_SYS_FSL_MAX_NUM_OF_SEC 1
+#elif defined(CONFIG_LS1012A)
+#define CONFIG_MAX_CPUS 1
+#define CONFIG_SYS_CACHELINE_SIZE 64
+#define CONFIG_NUM_DDR_CONTROLLERS 1
+#define CONFIG_SYS_CCSRBAR_DEFAULT 0x01000000
+#define CONFIG_SYS_FSL_SEC_COMPAT 5
+#undef CONFIG_SYS_FSL_DDRC_ARM_GEN3
+
+#define CONFIG_SYS_FSL_OCRAM_BASE 0x10000000 /* initial RAM */
+#define CONFIG_SYS_FSL_OCRAM_SIZE 0x200000 /* 2 MiB */
+
+#define GICD_BASE 0x01401000
+#define GICC_BASE 0x01402000
+
+#define CONFIG_SYS_FSL_CCSR_GUR_BE
+#define CONFIG_SYS_FSL_CCSR_SCFG_BE
+#define CONFIG_SYS_FSL_ESDHC_BE
+#define CONFIG_SYS_FSL_WDOG_BE
+#define CONFIG_SYS_FSL_DSPI_BE
+#define CONFIG_SYS_FSL_QSPI_BE
+#define CONFIG_SYS_FSL_PEX_LUT_BE
+
+#define SRDS_MAX_LANES 4
+#define CONFIG_SYS_FSL_SRDS_1
+#define CONFIG_SYS_FSL_PCIE_COMPAT "fsl,qoriq-pcie-v2.4"
+#define CONFIG_SYS_FSL_SEC_BE
#else
#error SoC not defined
#endif
CPU_TYPE_ENTRY(LS1043, LS1043, 4),
CPU_TYPE_ENTRY(LS1023, LS1023, 2),
CPU_TYPE_ENTRY(LS2040, LS2040, 4),
+ CPU_TYPE_ENTRY(LS1012, LS1012, 1),
};
#ifndef CONFIG_SYS_DCACHE_OFF
SGMII_2500_FM2_DTSEC6,
SGMII_2500_FM2_DTSEC9,
SGMII_2500_FM2_DTSEC10,
+ TX_CLK,
SERDES_PRCTL_COUNT
};
#define CONFIG_SYS_PCIE2_PHYS_ADDR 0x4800000000ULL
#define CONFIG_SYS_PCIE3_PHYS_ADDR 0x5000000000ULL
/* LUT registers */
+#ifdef CONFIG_LS1012A
+#define PCIE_LUT_BASE 0xC0000
+#else
#define PCIE_LUT_BASE 0x10000
+#endif
#define PCIE_LUT_LCTRL0 0x7F8
#define PCIE_LUT_DBG 0x7FC
CSU_CSLX_IIC4 = 77,
CSU_CSLX_WDT4,
CSU_CSLX_WDT3,
+ CSU_CSLX_ESDHC2 = 80,
CSU_CSLX_WDT5 = 81,
+ CSU_CSLX_SAI2,
+ CSU_CSLX_SAI1,
+ CSU_CSLX_SAI4,
+ CSU_CSLX_SAI3,
CSU_CSLX_FTM2 = 86,
CSU_CSLX_FTM1,
CSU_CSLX_FTM4,
{CSU_CSLX_IIC4, CSU_ALL_RW},
{CSU_CSLX_WDT4, CSU_ALL_RW},
{CSU_CSLX_WDT3, CSU_ALL_RW},
+ {CSU_CSLX_ESDHC2, CSU_ALL_RW},
{CSU_CSLX_WDT5, CSU_ALL_RW},
+ {CSU_CSLX_SAI2, CSU_ALL_RW},
+ {CSU_CSLX_SAI1, CSU_ALL_RW},
+ {CSU_CSLX_SAI4, CSU_ALL_RW},
+ {CSU_CSLX_SAI3, CSU_ALL_RW},
{CSU_CSLX_FTM2, CSU_ALL_RW},
{CSU_CSLX_FTM1, CSU_ALL_RW},
{CSU_CSLX_FTM4, CSU_ALL_RW},
{ .name = #n, .soc_ver = SVR_##v, .num_cores = (nc)}
#define SVR_WO_E 0xFFFFFE
+#define SVR_LS1012 0x870400
#define SVR_LS1043 0x879200
#define SVR_LS1023 0x879208
#define SVR_LS2045 0x870120
--- /dev/null
+/*
+ * Copyright 2016 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef FSL_MMDC_H
+#define FSL_MMDC_H
+
+#define CONFIG_SYS_MMDC_CORE_ODT_TIMING 0x12554000
+#define CONFIG_SYS_MMDC_CORE_TIMING_CFG_0 0xbabf7954
+#define CONFIG_SYS_MMDC_CORE_TIMING_CFG_1 0xff328f64
+#define CONFIG_SYS_MMDC_CORE_TIMING_CFG_2 0x01ff00db
+
+#define CONFIG_SYS_MMDC_CORE_MISC 0x00000680
+#define CONFIG_SYS_MMDC_PHY_MEASURE_UNIT 0x00000800
+#define CONFIG_SYS_MMDC_CORE_RDWR_CMD_DELAY 0x00002000
+#define CONFIG_SYS_MMDC_PHY_ODT_CTRL 0x0000022a
+
+#define CONFIG_SYS_MMDC_CORE_OUT_OF_RESET_DELAY 0x00bf1023
+
+#define CONFIG_SYS_MMDC_CORE_ADDR_PARTITION 0x0000007f
+
+#define CONFIG_SYS_MMDC_PHY_ZQ_HW_CTRL 0xa1390003
+
+#define FORCE_ZQ_AUTO_CALIBRATION (0x1 << 16)
+
+/* PHY Write Leveling Configuration and Error Status (MPWLGCR) */
+#define WR_LVL_HW_EN 0x00000001
+
+/* PHY Pre-defined Compare and CA delay-line Configuration (MPPDCMPR2) */
+#define MPR_COMPARE_EN 0x00000001
+
+#define CONFIG_SYS_MMDC_PHY_RD_DLY_LINES_CFG 0x40404040
+
+/* MMDC PHY Read DQS gating control register 0 (MPDGCTRL0) */
+#define AUTO_RD_DQS_GATING_CALIBRATION_EN 0x10000000
+
+/* MMDC PHY Read Delay HW Calibration Control Register (MPRDDLHWCTL) */
+#define AUTO_RD_CALIBRATION_EN 0x00000010
+
+#define CONFIG_SYS_MMDC_CORE_PWR_DOWN_CTRL 0x00030035
+
+#define CONFIG_SYS_MMDC_CORE_PWR_SAV_CTRL_STAT 0x00001067
+
+#define CONFIG_SYS_MMDC_CORE_REFRESH_CTL 0x103e8000
+
+#define START_REFRESH 0x00000001
+
+/* MMDC Core Special Command Register (MDSCR) */
+#define CMD_ADDR_MSB_MR_OP(x) (x << 24)
+
+#define CMD_ADDR_LSB_MR_ADDR(x) (x << 16)
+
+#define DISABLE_CFG_REQ 0x0
+#define CONFIGURATION_REQ (0x1 << 15)
+#define WL_EN (0x1 << 9)
+
+#define CMD_NORMAL (0x0 << 4)
+#define CMD_PRECHARGE (0x1 << 4)
+#define CMD_AUTO_REFRESH (0x2 << 4)
+#define CMD_LOAD_MODE_REG (0x3 << 4)
+#define CMD_ZQ_CALIBRATION (0x4 << 4)
+#define CMD_PRECHARGE_BANK_OPEN (0x5 << 4)
+#define CMD_MRR (0x6 << 4)
+
+#define CMD_BANK_ADDR_0 0x0
+#define CMD_BANK_ADDR_1 0x1
+#define CMD_BANK_ADDR_2 0x2
+#define CMD_BANK_ADDR_3 0x3
+#define CMD_BANK_ADDR_4 0x4
+#define CMD_BANK_ADDR_5 0x5
+#define CMD_BANK_ADDR_6 0x6
+#define CMD_BANK_ADDR_7 0x7
+
+/* MMDC Registers */
+struct mmdc_p_regs {
+ u32 mdctl;
+ u32 mdpdc;
+ u32 mdotc;
+ u32 mdcfg0;
+ u32 mdcfg1;
+ u32 mdcfg2;
+ u32 mdmisc;
+ u32 mdscr;
+ u32 mdref;
+ u32 res1[2];
+ u32 mdrwd;
+ u32 mdor;
+ u32 mdmrr;
+ u32 mdcfg3lp;
+ u32 mdmr4;
+ u32 mdasp;
+ u32 res2[239];
+ u32 maarcr;
+ u32 mapsr;
+ u32 maexidr0;
+ u32 maexidr1;
+ u32 madpcr0;
+ u32 madpcr1;
+ u32 madpsr0;
+ u32 madpsr1;
+ u32 madpsr2;
+ u32 madpsr3;
+ u32 madpsr4;
+ u32 madpsr5;
+ u32 masbs0;
+ u32 masbs1;
+ u32 res3[2];
+ u32 magenp;
+ u32 res4[239];
+ u32 mpzqhwctrl;
+ u32 mpzqswctrl;
+ u32 mpwlgcr;
+ u32 mpwldectrl0;
+ u32 mpwldectrl1;
+ u32 mpwldlst;
+ u32 mpodtctrl;
+ u32 mprddqby0dl;
+ u32 mprddqby1dl;
+ u32 mprddqby2dl;
+ u32 mprddqby3dl;
+ u32 res5[4];
+ u32 mpdgctrl0;
+ u32 mpdgctrl1;
+ u32 mpdgdlst0;
+ u32 mprddlctl;
+ u32 mprddlst;
+ u32 mpwrdlctl;
+ u32 mpwrdlst;
+ u32 mpsdctrl;
+ u32 mpzqlp2ctl;
+ u32 mprddlhwctl;
+ u32 mpwrdlhwctl;
+ u32 mprddlhwst0;
+ u32 mprddlhwst1;
+ u32 mpwrdlhwst0;
+ u32 mpwrdlhwst1;
+ u32 mpwlhwerr;
+ u32 mpdghwst0;
+ u32 mpdghwst1;
+ u32 mpdghwst2;
+ u32 mpdghwst3;
+ u32 mppdcmpr1;
+ u32 mppdcmpr2;
+ u32 mpswdar0;
+ u32 mpswdrdr0;
+ u32 mpswdrdr1;
+ u32 mpswdrdr2;
+ u32 mpswdrdr3;
+ u32 mpswdrdr4;
+ u32 mpswdrdr5;
+ u32 mpswdrdr6;
+ u32 mpswdrdr7;
+ u32 mpmur0;
+ u32 mpwrcadl;
+ u32 mpdccr;
+};
+
+#endif /* FSL_MMDC_H */
#define CONFIG_SYS_FSL_XHCI_USB1_ADDR CONFIG_SYS_LS2080A_XHCI_USB1_ADDR
#define CONFIG_SYS_FSL_XHCI_USB2_ADDR CONFIG_SYS_LS2080A_XHCI_USB2_ADDR
#define CONFIG_SYS_FSL_XHCI_USB3_ADDR 0
-#elif defined(CONFIG_LS1043A)
+#elif defined(CONFIG_LS1043A) || defined(CONFIG_LS1012A)
#define CONFIG_SYS_FSL_XHCI_USB1_ADDR CONFIG_SYS_LS1043A_XHCI_USB1_ADDR
#define CONFIG_SYS_FSL_XHCI_USB2_ADDR CONFIG_SYS_LS1043A_XHCI_USB2_ADDR
#define CONFIG_SYS_FSL_XHCI_USB3_ADDR CONFIG_SYS_LS1043A_XHCI_USB3_ADDR
+#elif defined(CONFIG_LS1012A)
+#define CONFIG_SYS_FSL_XHCI_USB1_ADDR CONFIG_SYS_LS1043A_XHCI_USB1_ADDR
+#define CONFIG_SYS_FSL_XHCI_USB2_ADDR 0
+#define CONFIG_SYS_FSL_XHCI_USB3_ADDR 0
#endif
#define FSL_USB_XHCI_ADDR {CONFIG_SYS_FSL_XHCI_USB1_ADDR, \
projects / platform / kernel / u-boot.git / commitdiff