spi: support inter-word delay requirement for devices

Some devices are slow and cannot keep up with the SPI bus and therefore
require a short delay between words of the SPI transfer.

The example of this that I'm looking at is a SAMA5D2 with a minimum SPI
clock of 400kHz talking to an AVR-based SPI slave.  The AVR cannot put
bytes on the bus fast enough to keep up with the SoC's SPI controller
even at the lowest bus speed.

This patch introduces the ability to specify a required inter-word
delay for SPI devices.  It is up to the controller driver to configure
itself accordingly in order to introduce the requested delay.

Note that, for spi_transfer, there is already a field word_delay that
provides similar functionality.  This field, however, is specified in
clock cycles (and worse, SPI controller cycles, not SCK cycles); that
makes this value dependent on the master clock instead of the device
clock for which the delay is intended to provide some relief.  This
patch leaves this old word_delay in place and provides a time-based
word_delay_us alongside it; the new field fits in the struct padding
so struct size is constant.  There is only one in-kernel user of the
word_delay field and presumably that driver could be reworked to use
the time-based value instead.

The time-based delay is limited to 8 bits as these delays are intended
to be short.  The SAMA5D2 that I've tested this on limits delays to a
maximum of ~100us, which is already many word-transfer periods even at
the minimum transfer speed supported by the controller.

Signed-off-by: Jonas Bonn <jonas@norrbonn.se>
CC: Mark Brown <broonie@kernel.org>
CC: Rob Herring <robh+dt@kernel.org>
CC: Mark Rutland <mark.rutland@arm.com>
CC: linux-spi@vger.kernel.org
CC: devicetree@vger.kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>

diff --git a/drivers/spi/spi.c b/drivers/spi/spi.c
index 0e0f2c6..2f7176f 100644 (file)
--- a/drivers/spi/spi.c
+++ b/drivers/spi/spi.c
@@ -3050,6 +3050,8 @@ static int __spi_validate(struct spi_device *spi, struct spi_message *message)
         * it is not set for this transfer.
         * Set transfer tx_nbits and rx_nbits as single transfer default
         * (SPI_NBITS_SINGLE) if it is not set for this transfer.
+        * Ensure transfer word_delay is at least as long as that required by
+        * device itself.
         */
        message->frame_length = 0;
        list_for_each_entry(xfer, &message->transfers, transfer_list) {
@@ -3120,6 +3122,9 @@ static int __spi_validate(struct spi_device *spi, struct spi_message *message)
                                !(spi->mode & SPI_RX_QUAD))
                                return -EINVAL;
                }
+
+               if (xfer->word_delay_usecs < spi->word_delay_usecs)
+                       xfer->word_delay_usecs = spi->word_delay_usecs;
        }
 
        message->status = -EINPROGRESS;

diff --git a/include/linux/spi/spi.h b/include/linux/spi/spi.h
index 916bba4..662b336 100644 (file)
--- a/include/linux/spi/spi.h
+++ b/include/linux/spi/spi.h
@@ -122,6 +122,8 @@ void spi_statistics_add_transfer_stats(struct spi_statistics *stats,
  *     the spi_master.
  * @cs_gpiod: gpio descriptor of the chipselect line (optional, NULL when
  *     not using a GPIO line)
+ * @word_delay_usecs: microsecond delay to be inserted between consecutive
+ *     words of a transfer
  *
  * @statistics: statistics for the spi_device
  *
@@ -169,6 +171,7 @@ struct spi_device {
        const char              *driver_override;
        int                     cs_gpio;        /* LEGACY: chip select gpio */
        struct gpio_desc        *cs_gpiod;      /* chip select gpio desc */
+       uint8_t                 word_delay_usecs; /* inter-word delay */
 
        /* the statistics */
        struct spi_statistics   statistics;
@@ -721,6 +724,8 @@ extern void spi_res_release(struct spi_controller *ctlr,
  * @delay_usecs: microseconds to delay after this transfer before
  *     (optionally) changing the chipselect status, then starting
  *     the next transfer or completing this @spi_message.
+ * @word_delay_usecs: microseconds to inter word delay after each word size
+ *     (set by bits_per_word) transmission.
  * @word_delay: clock cycles to inter word delay after each word size
  *     (set by bits_per_word) transmission.
  * @transfer_list: transfers are sequenced through @spi_message.transfers
@@ -803,6 +808,7 @@ struct spi_transfer {
 #define        SPI_NBITS_DUAL          0x02 /* 2bits transfer */
 #define        SPI_NBITS_QUAD          0x04 /* 4bits transfer */
        u8              bits_per_word;
+       u8              word_delay_usecs;
        u16             delay_usecs;
        u32             speed_hz;
        u16             word_delay;