bnx2x: Warpcore HW reset following fan failure

Put Warpcore in low power mode in case of fan failure to reduce heat.

Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

diff --git a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.c b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.c
index de03730..7eabcee 100644 (file)
--- a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.c
+++ b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.c
@@ -8216,7 +8216,15 @@ static void bnx2x_warpcore_power_module(struct link_params *params,
 static void bnx2x_warpcore_hw_reset(struct bnx2x_phy *phy,
                                    struct link_params *params)
 {
+       struct bnx2x *bp = params->bp;
        bnx2x_warpcore_power_module(params, phy, 0);
+       /* Put Warpcore in low power mode */
+       REG_WR(bp, MISC_REG_WC0_RESET, 0x0c0e);
+
+       /* Put LCPLL in low power mode */
+       REG_WR(bp, MISC_REG_LCPLL_E40_PWRDWN, 1);
+       REG_WR(bp, MISC_REG_LCPLL_E40_RESETB_ANA, 0);
+       REG_WR(bp, MISC_REG_LCPLL_E40_RESETB_DIG, 0);
 }
 
 static void bnx2x_power_sfp_module(struct link_params *params,

diff --git a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_reg.h b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_reg.h
index 92584d3..d5a0dde 100644 (file)
--- a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_reg.h
+++ b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_reg.h
@@ -1622,6 +1622,14 @@
    register bits. */
 #define MISC_REG_LCPLL_CTRL_1                                   0xa2a4
 #define MISC_REG_LCPLL_CTRL_REG_2                               0xa2a8
+/* [RW 1] LCPLL power down. Global register. Active High. Reset on POR
+ * reset. */
+#define MISC_REG_LCPLL_E40_PWRDWN                               0xaa74
+/* [RW 1] LCPLL VCO reset. Global register. Active Low Reset on POR reset. */
+#define MISC_REG_LCPLL_E40_RESETB_ANA                           0xaa78
+/* [RW 1] LCPLL post-divider reset. Global register. Active Low Reset on POR
+ * reset. */
+#define MISC_REG_LCPLL_E40_RESETB_DIG                           0xaa7c
 /* [RW 4] Interrupt mask register #0 read/write */
 #define MISC_REG_MISC_INT_MASK                                  0xa388
 /* [RW 1] Parity mask register #0 read/write */
@@ -1757,6 +1765,7 @@
  * is compared to the value on ctrl_md_devad. Drives output
  * misc_xgxs0_phy_addr. Global register. */
 #define MISC_REG_WC0_CTRL_PHY_ADDR                              0xa9cc
+#define MISC_REG_WC0_RESET                                      0xac30
 /* [RW 2] XMAC Core port mode. Indicates the number of ports on the system
    side. This should be less than or equal to phy_port_mode; if some of the
    ports are not used. This enables reduction of frequency on the core side.