imx6ul: opos6ul: migrate to DM_ETH

Migrate to DM_ETH and remove code that is no longer necessary.

Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>

diff --git a/arch/arm/mach-imx/mx6/opos6ul.c b/arch/arm/mach-imx/mx6/opos6ul.c
index 3ab9a3f..0c640e2 100644 (file)
--- a/arch/arm/mach-imx/mx6/opos6ul.c
+++ b/arch/arm/mach-imx/mx6/opos6ul.c
@@ -6,11 +6,7 @@
 #include <asm/arch/clock.h>
 #include <asm/arch/crm_regs.h>
 #include <asm/arch/imx-regs.h>
-#include <asm/arch/iomux.h>
-#include <asm/arch/mx6-pins.h>
 #include <asm/arch/sys_proto.h>
-#include <asm/gpio.h>
-#include <asm/mach-imx/iomux-v3.h>
 #include <asm/io.h>
 #include <common.h>
 #include <env.h>
@@ -20,43 +16,6 @@ DECLARE_GLOBAL_DATA_PTR;
 #ifdef CONFIG_FEC_MXC
 #include <miiphy.h>
 
-#define MDIO_PAD_CTRL ( \
-       PAD_CTL_HYS | PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
-       PAD_CTL_DSE_40ohm \
-)
-
-#define ENET_PAD_CTRL_PU ( \
-       PAD_CTL_HYS | PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
-       PAD_CTL_DSE_40ohm \
-)
-
-#define ENET_PAD_CTRL_PD ( \
-       PAD_CTL_HYS | PAD_CTL_PUS_100K_DOWN | PAD_CTL_SPEED_MED | \
-       PAD_CTL_DSE_40ohm \
-)
-
-#define ENET_CLK_PAD_CTRL ( \
-       PAD_CTL_HYS | PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_LOW | \
-       PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST \
-)
-
-static iomux_v3_cfg_t const fec1_pads[] = {
-       MX6_PAD_GPIO1_IO06__ENET1_MDIO        | MUX_PAD_CTRL(MDIO_PAD_CTRL),
-       MX6_PAD_GPIO1_IO07__ENET1_MDC         | MUX_PAD_CTRL(MDIO_PAD_CTRL),
-       MX6_PAD_ENET1_RX_ER__ENET1_RX_ER      | MUX_PAD_CTRL(ENET_PAD_CTRL_PD),
-       MX6_PAD_ENET1_RX_EN__ENET1_RX_EN      | MUX_PAD_CTRL(ENET_PAD_CTRL_PD),
-       MX6_PAD_ENET1_RX_DATA1__ENET1_RDATA01 | MUX_PAD_CTRL(ENET_PAD_CTRL_PD),
-       MX6_PAD_ENET1_RX_DATA0__ENET1_RDATA00 | MUX_PAD_CTRL(ENET_PAD_CTRL_PD),
-       MX6_PAD_ENET1_TX_DATA0__ENET1_TDATA00 | MUX_PAD_CTRL(ENET_PAD_CTRL_PU),
-       MX6_PAD_ENET1_TX_DATA1__ENET1_TDATA01 | MUX_PAD_CTRL(ENET_PAD_CTRL_PU),
-       MX6_PAD_ENET1_TX_EN__ENET1_TX_EN      | MUX_PAD_CTRL(ENET_PAD_CTRL_PU),
-       /* PHY Int */
-       MX6_PAD_NAND_DQS__GPIO4_IO16          | MUX_PAD_CTRL(ENET_PAD_CTRL_PU),
-       /* PHY Reset */
-       MX6_PAD_NAND_DATA00__GPIO4_IO02       | MUX_PAD_CTRL(ENET_PAD_CTRL_PD),
-       MX6_PAD_ENET1_TX_CLK__ENET1_REF_CLK1  | MUX_PAD_CTRL(ENET_CLK_PAD_CTRL),
-};
-
 int board_phy_config(struct phy_device *phydev)
 {
        phy_write(phydev, MDIO_DEVAD_NONE, 0x1f, 0x8190);
@@ -67,43 +26,16 @@ int board_phy_config(struct phy_device *phydev)
        return 0;
 }
 
-int board_eth_init(bd_t *bis)
+static int setup_fec(void)
 {
        struct iomuxc *const iomuxc_regs = (struct iomuxc *)IOMUXC_BASE_ADDR;
-       struct gpio_desc rst;
-       int ret;
 
        /* Use 50M anatop loopback REF_CLK1 for ENET1,
         * clear gpr1[13], set gpr1[17] */
        clrsetbits_le32(&iomuxc_regs->gpr[1], IOMUX_GPR1_FEC1_MASK,
                        IOMUX_GPR1_FEC1_CLOCK_MUX1_SEL_MASK);
 
-       ret = enable_fec_anatop_clock(0, ENET_50MHZ);
-       if (ret)
-               return ret;
-
-       enable_enet_clk(1);
-
-       imx_iomux_v3_setup_multiple_pads(fec1_pads, ARRAY_SIZE(fec1_pads));
-
-       ret = dm_gpio_lookup_name("GPIO4_2", &rst);
-       if (ret) {
-               printf("Cannot get GPIO4_2\n");
-               return ret;
-       }
-
-       ret = dm_gpio_request(&rst, "phy-rst");
-       if (ret) {
-               printf("Cannot request GPIO4_2\n");
-               return ret;
-       }
-
-       dm_gpio_set_dir_flags(&rst, GPIOD_IS_OUT);
-       dm_gpio_set_value(&rst, 0);
-       udelay(1000);
-       dm_gpio_set_value(&rst, 1);
-
-       return fecmxc_initialize(bis);
+       return enable_fec_anatop_clock(0, ENET_50MHZ);
 }
 #endif /* CONFIG_FEC_MXC */
 
@@ -112,6 +44,10 @@ int board_init(void)
        /* Address of boot parameters */
        gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
 
+#ifdef CONFIG_FEC_MXC
+       setup_fec();
+#endif
+
        return 0;
 }
 

diff --git a/configs/opos6uldev_defconfig b/configs/opos6uldev_defconfig
index 5eef652..44236e9 100644 (file)
--- a/configs/opos6uldev_defconfig
+++ b/configs/opos6uldev_defconfig
@@ -73,6 +73,8 @@ CONFIG_FSL_USDHC=y
 CONFIG_PHYLIB=y
 CONFIG_PHY_MICREL=y
 CONFIG_PHY_MICREL_KSZ8XXX=y
+CONFIG_DM_ETH=y
+CONFIG_DM_MDIO=y
 CONFIG_FEC_MXC=y
 CONFIG_MII=y
 CONFIG_PINCTRL=y

diff --git a/include/configs/opos6uldev.h b/include/configs/opos6uldev.h
index 309b471..744317d 100644 (file)
--- a/include/configs/opos6uldev.h
+++ b/include/configs/opos6uldev.h
@@ -41,14 +41,6 @@
 #define CONFIG_USB_MAX_CONTROLLER_COUNT        2
 #endif
 
-/* Ethernet */
-#ifdef CONFIG_FEC_MXC
-#define IMX_FEC_BASE                   ENET_BASE_ADDR
-#define CONFIG_FEC_MXC_PHYADDR          0x1
-#define CONFIG_FEC_XCV_TYPE             RMII
-#define CONFIG_ETHPRIME                        "FEC"
-#endif
-
 /* LCD */
 #ifndef CONFIG_SPL_BUILD
 #ifdef CONFIG_VIDEO