rockchip: rk3288: Move veyron_init() back to veyron.c

The veyron_init() should go to its board file veyron.c,
and the board_early_init_f() could be the right place.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>

diff --git a/arch/arm/mach-rockchip/rk3288-board.c b/arch/arm/mach-rockchip/rk3288-board.c
index e629df3..915f82e 100644 (file)
--- a/arch/arm/mach-rockchip/rk3288-board.c
+++ b/arch/arm/mach-rockchip/rk3288-board.c
@@ -15,7 +15,6 @@
 #include <asm/arch-rockchip/pmu_rk3288.h>
 #include <asm/arch-rockchip/boot_mode.h>
 #include <asm/gpio.h>
-#include <dt-bindings/clock/rk3288-cru.h>
 #include <power/regulator.h>
 
 DECLARE_GLOBAL_DATA_PTR;
@@ -70,73 +69,9 @@ int board_late_init(void)
        return rk_board_late_init();
 }
 
-#if !CONFIG_IS_ENABLED(ROCKCHIP_BACK_TO_BROM)
-static int veyron_init(void)
-{
-       struct udevice *dev;
-       struct clk clk;
-       int ret;
-
-       ret = regulator_get_by_platname("vdd_arm", &dev);
-       if (ret) {
-               debug("Cannot set regulator name\n");
-               return ret;
-       }
-
-       /* Slowly raise to max CPU voltage to prevent overshoot */
-       ret = regulator_set_value(dev, 1200000);
-       if (ret)
-               return ret;
-       udelay(175); /* Must wait for voltage to stabilize, 2mV/us */
-       ret = regulator_set_value(dev, 1400000);
-       if (ret)
-               return ret;
-       udelay(100); /* Must wait for voltage to stabilize, 2mV/us */
-
-       ret = rockchip_get_clk(&clk.dev);
-       if (ret)
-               return ret;
-       clk.id = PLL_APLL;
-       ret = clk_set_rate(&clk, 1800000000);
-       if (IS_ERR_VALUE(ret))
-               return ret;
-
-       ret = regulator_get_by_platname("vcc33_sd", &dev);
-       if (ret) {
-               debug("Cannot get regulator name\n");
-               return ret;
-       }
-
-       ret = regulator_set_value(dev, 3300000);
-       if (ret)
-               return ret;
-
-       ret = regulators_enable_boot_on(false);
-       if (ret) {
-               debug("%s: Cannot enable boot on regulators\n", __func__);
-               return ret;
-       }
-
-       return 0;
-}
-#endif
-
 int board_init(void)
 {
-#if CONFIG_IS_ENABLED(ROCKCHIP_BACK_TO_BROM)
        return 0;
-#else
-       int ret;
-
-       /* We do some SoC one time setting here */
-       if (!fdt_node_check_compatible(gd->fdt_blob, 0, "google,veyron")) {
-               ret = veyron_init();
-               if (ret)
-                       return ret;
-       }
-
-       return 0;
-#endif
 }
 
 #if !CONFIG_IS_ENABLED(SYS_DCACHE_OFF)

diff --git a/board/google/veyron/veyron.c b/board/google/veyron/veyron.c
index 361f0e9..dd2c014 100644 (file)
--- a/board/google/veyron/veyron.c
+++ b/board/google/veyron/veyron.c
@@ -3,20 +3,82 @@
  * (C) Copyright 2015 Google, Inc
  */
 
+#include <clk.h>
 #include <common.h>
+#include <dm.h>
 #include <asm/arch-rockchip/clock.h>
+#include <dt-bindings/clock/rk3288-cru.h>
+#include <power/regulator.h>
 
 /*
  * We should increase the DDR voltage to 1.2V using the PWM regulator.
  * There is a U-Boot driver for this but it may need to add support for the
  * 'voltage-table' property.
  */
+#ifndef CONFIG_SPL_BUILD
+#if !CONFIG_IS_ENABLED(ROCKCHIP_BACK_TO_BROM)
+static int veyron_init(void)
+{
+       struct udevice *dev;
+       struct clk clk;
+       int ret;
+
+       ret = regulator_get_by_platname("vdd_arm", &dev);
+       if (ret) {
+               debug("Cannot set regulator name\n");
+               return ret;
+       }
+
+       /* Slowly raise to max CPU voltage to prevent overshoot */
+       ret = regulator_set_value(dev, 1200000);
+       if (ret)
+               return ret;
+       udelay(175); /* Must wait for voltage to stabilize, 2mV/us */
+       ret = regulator_set_value(dev, 1400000);
+       if (ret)
+               return ret;
+       udelay(100); /* Must wait for voltage to stabilize, 2mV/us */
+
+       ret = rockchip_get_clk(&clk.dev);
+       if (ret)
+               return ret;
+       clk.id = PLL_APLL;
+       ret = clk_set_rate(&clk, 1800000000);
+       if (IS_ERR_VALUE(ret))
+               return ret;
+
+       ret = regulator_get_by_platname("vcc33_sd", &dev);
+       if (ret) {
+               debug("Cannot get regulator name\n");
+               return ret;
+       }
+
+       ret = regulator_set_value(dev, 3300000);
+       if (ret)
+               return ret;
+
+       ret = regulators_enable_boot_on(false);
+       if (ret) {
+               debug("%s: Cannot enable boot on regulators\n", __func__);
+               return ret;
+       }
+
+       return 0;
+}
+#endif
 
 int board_early_init_f(void)
 {
        struct udevice *dev;
        int ret;
 
+#if !CONFIG_IS_ENABLED(ROCKCHIP_BACK_TO_BROM)
+       if (!fdt_node_check_compatible(gd->fdt_blob, 0, "google,veyron")) {
+               ret = veyron_init();
+               if (ret)
+                       return ret;
+       }
+#endif
        /*
         * This init is done in SPL, but when chain-loading U-Boot SPL will
         * have been skipped. Allow the clock driver to check if it needs
@@ -30,3 +92,4 @@ int board_early_init_f(void)
 
        return 0;
 }
+#endif