#include <linux/of_platform.h>
#include <linux/if_bridge.h>
#include <linux/mdio.h>
+#include <linux/phylink.h>
#include <linux/gpio/consumer.h>
#include <linux/etherdevice.h>
mutex_unlock(&priv->reg_mutex);
}
-static int
-qca8k_set_pad_ctrl(struct qca8k_priv *priv, int port, int mode)
-{
- u32 reg, val;
-
- switch (port) {
- case 0:
- reg = QCA8K_REG_PORT0_PAD_CTRL;
- break;
- case 6:
- reg = QCA8K_REG_PORT6_PAD_CTRL;
- break;
- default:
- pr_err("Can't set PAD_CTRL on port %d\n", port);
- return -EINVAL;
- }
-
- /* Configure a port to be directly connected to an external
- * PHY or MAC.
- */
- switch (mode) {
- case PHY_INTERFACE_MODE_RGMII:
- /* RGMII mode means no delay so don't enable the delay */
- val = QCA8K_PORT_PAD_RGMII_EN;
- qca8k_write(priv, reg, val);
- break;
- case PHY_INTERFACE_MODE_RGMII_ID:
- /* RGMII_ID needs internal delay. This is enabled through
- * PORT5_PAD_CTRL for all ports, rather than individual port
- * registers
- */
- qca8k_write(priv, reg,
- QCA8K_PORT_PAD_RGMII_EN |
- QCA8K_PORT_PAD_RGMII_TX_DELAY(QCA8K_MAX_DELAY) |
- QCA8K_PORT_PAD_RGMII_RX_DELAY(QCA8K_MAX_DELAY));
- qca8k_write(priv, QCA8K_REG_PORT5_PAD_CTRL,
- QCA8K_PORT_PAD_RGMII_RX_DELAY_EN);
- break;
- case PHY_INTERFACE_MODE_SGMII:
- qca8k_write(priv, reg, QCA8K_PORT_PAD_SGMII_EN);
- break;
- default:
- pr_err("xMII mode %d not supported\n", mode);
- return -EINVAL;
- }
-
- return 0;
-}
-
static void
qca8k_port_set_status(struct qca8k_priv *priv, int port, int enable)
{
qca8k_setup(struct dsa_switch *ds)
{
struct qca8k_priv *priv = (struct qca8k_priv *)ds->priv;
- phy_interface_t phy_mode = PHY_INTERFACE_MODE_NA;
int ret, i;
- u32 mask;
/* Make sure that port 0 is the cpu port */
if (!dsa_is_cpu_port(ds, 0)) {
if (ret)
return ret;
- /* Initialize CPU port pad mode (xMII type, delays...) */
- ret = of_get_phy_mode(dsa_to_port(ds, QCA8K_CPU_PORT)->dn, &phy_mode);
- if (ret) {
- pr_err("Can't find phy-mode for master device\n");
- return ret;
- }
- ret = qca8k_set_pad_ctrl(priv, QCA8K_CPU_PORT, phy_mode);
- if (ret < 0)
- return ret;
-
- /* Enable CPU Port, force it to maximum bandwidth and full-duplex */
- mask = QCA8K_PORT_STATUS_SPEED_1000 | QCA8K_PORT_STATUS_TXFLOW |
- QCA8K_PORT_STATUS_RXFLOW | QCA8K_PORT_STATUS_DUPLEX;
- qca8k_write(priv, QCA8K_REG_PORT_STATUS(QCA8K_CPU_PORT), mask);
+ /* Enable CPU Port */
qca8k_reg_set(priv, QCA8K_REG_GLOBAL_FW_CTRL0,
QCA8K_GLOBAL_FW_CTRL0_CPU_PORT_EN);
- qca8k_port_set_status(priv, QCA8K_CPU_PORT, 1);
- priv->port_sts[QCA8K_CPU_PORT].enabled = 1;
/* Enable MIB counters */
qca8k_mib_init(priv);
qca8k_rmw(priv, QCA8K_PORT_LOOKUP_CTRL(i),
QCA8K_PORT_LOOKUP_MEMBER, 0);
- /* Disable MAC by default on all user ports */
+ /* Disable MAC by default on all ports */
for (i = 1; i < QCA8K_NUM_PORTS; i++)
- if (dsa_is_user_port(ds, i))
- qca8k_port_set_status(priv, i, 0);
+ qca8k_port_set_status(priv, i, 0);
/* Forward all unknown frames to CPU port for Linux processing */
qca8k_write(priv, QCA8K_REG_GLOBAL_FW_CTRL1,
}
static void
-qca8k_adjust_link(struct dsa_switch *ds, int port, struct phy_device *phy)
+qca8k_phylink_mac_config(struct dsa_switch *ds, int port, unsigned int mode,
+ const struct phylink_link_state *state)
{
struct qca8k_priv *priv = ds->priv;
u32 reg;
- /* Force fixed-link setting for CPU port, skip others. */
- if (!phy_is_pseudo_fixed_link(phy))
+ switch (port) {
+ case 0: /* 1st CPU port */
+ if (state->interface != PHY_INTERFACE_MODE_RGMII &&
+ state->interface != PHY_INTERFACE_MODE_RGMII_ID &&
+ state->interface != PHY_INTERFACE_MODE_SGMII)
+ return;
+
+ reg = QCA8K_REG_PORT0_PAD_CTRL;
+ break;
+ case 1:
+ case 2:
+ case 3:
+ case 4:
+ case 5:
+ /* Internal PHY, nothing to do */
+ return;
+ case 6: /* 2nd CPU port / external PHY */
+ if (state->interface != PHY_INTERFACE_MODE_RGMII &&
+ state->interface != PHY_INTERFACE_MODE_RGMII_ID &&
+ state->interface != PHY_INTERFACE_MODE_SGMII &&
+ state->interface != PHY_INTERFACE_MODE_1000BASEX)
+ return;
+
+ reg = QCA8K_REG_PORT6_PAD_CTRL;
+ break;
+ default:
+ dev_err(ds->dev, "%s: unsupported port: %i\n", __func__, port);
+ return;
+ }
+
+ if (port != 6 && phylink_autoneg_inband(mode)) {
+ dev_err(ds->dev, "%s: in-band negotiation unsupported\n",
+ __func__);
+ return;
+ }
+
+ switch (state->interface) {
+ case PHY_INTERFACE_MODE_RGMII:
+ /* RGMII mode means no delay so don't enable the delay */
+ qca8k_write(priv, reg, QCA8K_PORT_PAD_RGMII_EN);
+ break;
+ case PHY_INTERFACE_MODE_RGMII_ID:
+ /* RGMII_ID needs internal delay. This is enabled through
+ * PORT5_PAD_CTRL for all ports, rather than individual port
+ * registers
+ */
+ qca8k_write(priv, reg,
+ QCA8K_PORT_PAD_RGMII_EN |
+ QCA8K_PORT_PAD_RGMII_TX_DELAY(QCA8K_MAX_DELAY) |
+ QCA8K_PORT_PAD_RGMII_RX_DELAY(QCA8K_MAX_DELAY));
+ qca8k_write(priv, QCA8K_REG_PORT5_PAD_CTRL,
+ QCA8K_PORT_PAD_RGMII_RX_DELAY_EN);
+ break;
+ case PHY_INTERFACE_MODE_SGMII:
+ case PHY_INTERFACE_MODE_1000BASEX:
+ /* Enable SGMII on the port */
+ qca8k_write(priv, reg, QCA8K_PORT_PAD_SGMII_EN);
+ break;
+ default:
+ dev_err(ds->dev, "xMII mode %s not supported for port %d\n",
+ phy_modes(state->interface), port);
return;
+ }
+}
- /* Set port speed */
- switch (phy->speed) {
- case 10:
- reg = QCA8K_PORT_STATUS_SPEED_10;
+static void
+qca8k_phylink_validate(struct dsa_switch *ds, int port,
+ unsigned long *supported,
+ struct phylink_link_state *state)
+{
+ __ETHTOOL_DECLARE_LINK_MODE_MASK(mask) = { 0, };
+
+ switch (port) {
+ case 0: /* 1st CPU port */
+ if (state->interface != PHY_INTERFACE_MODE_NA &&
+ state->interface != PHY_INTERFACE_MODE_RGMII &&
+ state->interface != PHY_INTERFACE_MODE_RGMII_ID &&
+ state->interface != PHY_INTERFACE_MODE_SGMII)
+ goto unsupported;
break;
- case 100:
- reg = QCA8K_PORT_STATUS_SPEED_100;
+ case 1:
+ case 2:
+ case 3:
+ case 4:
+ case 5:
+ /* Internal PHY */
+ if (state->interface != PHY_INTERFACE_MODE_NA &&
+ state->interface != PHY_INTERFACE_MODE_GMII)
+ goto unsupported;
break;
- case 1000:
- reg = QCA8K_PORT_STATUS_SPEED_1000;
+ case 6: /* 2nd CPU port / external PHY */
+ if (state->interface != PHY_INTERFACE_MODE_NA &&
+ state->interface != PHY_INTERFACE_MODE_RGMII &&
+ state->interface != PHY_INTERFACE_MODE_RGMII_ID &&
+ state->interface != PHY_INTERFACE_MODE_SGMII &&
+ state->interface != PHY_INTERFACE_MODE_1000BASEX)
+ goto unsupported;
break;
default:
- dev_dbg(priv->dev, "port%d link speed %dMbps not supported.\n",
- port, phy->speed);
+unsupported:
+ linkmode_zero(supported);
return;
}
- /* Set duplex mode */
- if (phy->duplex == DUPLEX_FULL)
- reg |= QCA8K_PORT_STATUS_DUPLEX;
+ phylink_set_port_modes(mask);
+ phylink_set(mask, Autoneg);
+
+ phylink_set(mask, 1000baseT_Full);
+ phylink_set(mask, 10baseT_Half);
+ phylink_set(mask, 10baseT_Full);
+ phylink_set(mask, 100baseT_Half);
+ phylink_set(mask, 100baseT_Full);
+
+ if (state->interface == PHY_INTERFACE_MODE_1000BASEX)
+ phylink_set(mask, 1000baseX_Full);
+
+ phylink_set(mask, Pause);
+ phylink_set(mask, Asym_Pause);
+
+ linkmode_and(supported, supported, mask);
+ linkmode_and(state->advertising, state->advertising, mask);
+}
+
+static int
+qca8k_phylink_mac_link_state(struct dsa_switch *ds, int port,
+ struct phylink_link_state *state)
+{
+ struct qca8k_priv *priv = ds->priv;
+ u32 reg;
- /* Force flow control */
- if (dsa_is_cpu_port(ds, port))
- reg |= QCA8K_PORT_STATUS_RXFLOW | QCA8K_PORT_STATUS_TXFLOW;
+ reg = qca8k_read(priv, QCA8K_REG_PORT_STATUS(port));
+
+ state->link = !!(reg & QCA8K_PORT_STATUS_LINK_UP);
+ state->an_complete = state->link;
+ state->an_enabled = !!(reg & QCA8K_PORT_STATUS_LINK_AUTO);
+ state->duplex = (reg & QCA8K_PORT_STATUS_DUPLEX) ? DUPLEX_FULL :
+ DUPLEX_HALF;
+
+ switch (reg & QCA8K_PORT_STATUS_SPEED) {
+ case QCA8K_PORT_STATUS_SPEED_10:
+ state->speed = SPEED_10;
+ break;
+ case QCA8K_PORT_STATUS_SPEED_100:
+ state->speed = SPEED_100;
+ break;
+ case QCA8K_PORT_STATUS_SPEED_1000:
+ state->speed = SPEED_1000;
+ break;
+ default:
+ state->speed = SPEED_UNKNOWN;
+ break;
+ }
+
+ state->pause = MLO_PAUSE_NONE;
+ if (reg & QCA8K_PORT_STATUS_RXFLOW)
+ state->pause |= MLO_PAUSE_RX;
+ if (reg & QCA8K_PORT_STATUS_TXFLOW)
+ state->pause |= MLO_PAUSE_TX;
+
+ return 1;
+}
+
+static void
+qca8k_phylink_mac_link_down(struct dsa_switch *ds, int port, unsigned int mode,
+ phy_interface_t interface)
+{
+ struct qca8k_priv *priv = ds->priv;
- /* Force link down before changing MAC options */
qca8k_port_set_status(priv, port, 0);
+}
+
+static void
+qca8k_phylink_mac_link_up(struct dsa_switch *ds, int port, unsigned int mode,
+ phy_interface_t interface, struct phy_device *phydev,
+ int speed, int duplex, bool tx_pause, bool rx_pause)
+{
+ struct qca8k_priv *priv = ds->priv;
+ u32 reg;
+
+ if (phylink_autoneg_inband(mode)) {
+ reg = QCA8K_PORT_STATUS_LINK_AUTO;
+ } else {
+ switch (speed) {
+ case SPEED_10:
+ reg = QCA8K_PORT_STATUS_SPEED_10;
+ break;
+ case SPEED_100:
+ reg = QCA8K_PORT_STATUS_SPEED_100;
+ break;
+ case SPEED_1000:
+ reg = QCA8K_PORT_STATUS_SPEED_1000;
+ break;
+ default:
+ reg = QCA8K_PORT_STATUS_LINK_AUTO;
+ break;
+ }
+
+ if (duplex == DUPLEX_FULL)
+ reg |= QCA8K_PORT_STATUS_DUPLEX;
+
+ if (rx_pause || dsa_is_cpu_port(ds, port))
+ reg |= QCA8K_PORT_STATUS_RXFLOW;
+
+ if (tx_pause || dsa_is_cpu_port(ds, port))
+ reg |= QCA8K_PORT_STATUS_TXFLOW;
+ }
+
+ reg |= QCA8K_PORT_STATUS_TXMAC | QCA8K_PORT_STATUS_RXMAC;
+
qca8k_write(priv, QCA8K_REG_PORT_STATUS(port), reg);
- qca8k_port_set_status(priv, port, 1);
}
static void
{
struct qca8k_priv *priv = (struct qca8k_priv *)ds->priv;
- if (!dsa_is_user_port(ds, port))
- return 0;
-
qca8k_port_set_status(priv, port, 1);
priv->port_sts[port].enabled = 1;
- phy_support_asym_pause(phy);
+ if (dsa_is_user_port(ds, port))
+ phy_support_asym_pause(phy);
return 0;
}
static const struct dsa_switch_ops qca8k_switch_ops = {
.get_tag_protocol = qca8k_get_tag_protocol,
.setup = qca8k_setup,
- .adjust_link = qca8k_adjust_link,
.get_strings = qca8k_get_strings,
.get_ethtool_stats = qca8k_get_ethtool_stats,
.get_sset_count = qca8k_get_sset_count,
.port_fdb_add = qca8k_port_fdb_add,
.port_fdb_del = qca8k_port_fdb_del,
.port_fdb_dump = qca8k_port_fdb_dump,
+ .phylink_validate = qca8k_phylink_validate,
+ .phylink_mac_link_state = qca8k_phylink_mac_link_state,
+ .phylink_mac_config = qca8k_phylink_mac_config,
+ .phylink_mac_link_down = qca8k_phylink_mac_link_down,
+ .phylink_mac_link_up = qca8k_phylink_mac_link_up,
};
static int
projects / platform / kernel / linux-starfive.git / commitdiff