This board has not been converted to generic board by the deadline.
Remove it.
Signed-off-by: Simon Glass <sjg@chromium.org>
config TARGET_NETSPACE_V2
bool "LaCie netspace_v2 Board"
-config TARGET_WIRELESS_SPACE
- bool "LaCie Wireless_space Board"
-
config TARGET_IB62X0
bool "ib62x0 Board"
source "board/keymile/km_arm/Kconfig"
source "board/LaCie/net2big_v2/Kconfig"
source "board/LaCie/netspace_v2/Kconfig"
-source "board/LaCie/wireless_space/Kconfig"
source "board/raidsonic/ib62x0/Kconfig"
source "board/Seagate/dockstar/Kconfig"
source "board/Seagate/goflexhome/Kconfig"
+++ /dev/null
-if TARGET_WIRELESS_SPACE
-
-config SYS_BOARD
- default "wireless_space"
-
-config SYS_VENDOR
- default "LaCie"
-
-config SYS_CONFIG_NAME
- default "wireless_space"
-
-endif
+++ /dev/null
-WIRELESS_SPACE BOARD
-M: Albert ARIBAUD <albert.u.boot@aribaud.net>
-S: Maintained
-F: board/LaCie/wireless_space/
-F: include/configs/wireless_space.h
-F: configs/wireless_space_defconfig
+++ /dev/null
-#
-# Copyright (C) 2011 Simon Guinot <sguinot@lacie.com>
-#
-# Based on Kirkwood support:
-# (C) Copyright 2009
-# Marvell Semiconductor <www.marvell.com>
-# Written-by: Prafulla Wadaskar <prafulla@marvell.com>
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-obj-y := wireless_space.o ../common/common.o
+++ /dev/null
-#
-# Copyright (C) 2012 Albert ARIBAUD <albert.u.boot@aribaud.net>
-#
-# Based on netspace_v2 kwbimage.cfg:
-# Copyright (C) 2011 Simon Guinot <sguinot@lacie.com>
-#
-# Based on Kirkwood support:
-# (C) Copyright 2009
-# Marvell Semiconductor <www.marvell.com>
-# Written-by: Prafulla Wadaskar <prafulla@marvell.com>
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-# Refer doc/README.kwbimage for more details about how-to configure
-# and create kirkwood boot image
-#
-
-# Boot Media configurations
-BOOT_FROM nand # Boot from NAND flash
-NAND_PAGE_SIZE 800
-
-# SOC registers configuration using bootrom header extension
-# Maximum KWBIMAGE_MAX_CONFIG configurations allowed
-
-# Values taken from image original LaCie U-Boot header dump!
-
-# Configure RGMII-0 interface pad voltage to 1.8V
-DATA 0xFFD100e0 0x1B1B1B9B
-
-#Dram initalization for SINGLE x16 CL=5 @ 400MHz
-DATA 0xFFD01400 0x43000c30 # DDR Configuration register
-
-DATA 0xFFD01404 0x37743000 # DDR Controller Control Low
-
-DATA 0xFFD01408 0x11012228 # DDR Timing (Low) (active cycles value +1)
-
-DATA 0xFFD0140C 0x00000A19 # DDR Timing (High)
-
-DATA 0xFFD01410 0x0000CCCC # DDR Address Control
-
-DATA 0xFFD01414 0x00000000 # DDR Open Pages Control
-
-DATA 0xFFD01418 0x00000000 # DDR Operation
-
-DATA 0xFFD0141C 0x00000662 # DDR Mode
-
-DATA 0xFFD01420 0x00000004 # DDR Extended Mode
-
-DATA 0xFFD01424 0x0000F07F # DDR Controller Control High
-
-DATA 0xFFD01428 0x00096630 # DDR2 ODT Read Timing (default values)
-
-DATA 0xFFD0147C 0x00009663 # DDR2 ODT Write Timing (default values)
-
-DATA 0xFFD01504 0x0FFFFFF1 # CS[0]n Size
-DATA 0xFFD01508 0x00000000 # CS[1]n Base address to 0x0
-DATA 0xFFD0150C 0x00000000 # CS[1]n Size, window disabled
-DATA 0xFFD01514 0x00000000 # CS[2]n Size, window disabled
-DATA 0xFFD0151C 0x00000000 # CS[3]n Size, window disabled
-DATA 0xFFD01494 0x00120012 # DDR ODT Control (Low)
-DATA 0xFFD01498 0x00000000 # DDR ODT Control (High)
-DATA 0xFFD0149C 0x0000E40F # CPU ODT Control
-DATA 0xFFD01480 0x00000001 # DDR Initialization Control
-DATA 0xFFD20134 0x66666666
-DATA 0xFFD20138 0x66666666
-DATA 0xFFD10000 0x01112222
-DATA 0xFFD1000C 0x00000000
-DATA 0xFFD10104 0x00000000
-DATA 0xFFD10100 0x40000000
-# End of Header extension
-DATA 0x0 0x0
+++ /dev/null
-/*
- * Copyright (C) 2011 Simon Guinot <sguinot@lacie.com>
- *
- * Based on Kirkwood support:
- * (C) Copyright 2009
- * Marvell Semiconductor <www.marvell.com>
- * Written-by: Prafulla Wadaskar <prafulla@marvell.com>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <command.h>
-#include <asm/arch/cpu.h>
-#include <asm/arch/soc.h>
-#include <asm/arch/mpp.h>
-#include <asm/arch/gpio.h>
-
-#include "../common/common.h"
-#include "netdev.h"
-
-DECLARE_GLOBAL_DATA_PTR;
-
-/* GPIO configuration: start FAN at low speed, USB and HDD */
-
-#define WIRELESS_SPACE_OE_LOW 0xFF006808
-#define WIRELESS_SPACE_OE_HIGH 0x0000F989
-#define WIRELESS_SPACE_OE_VAL_LOW 0x00010080
-#define WIRELESS_SPACE_OE_VAL_HIGH 0x00000240
-
-#define WIRELESS_SPACE_REAR_BUTTON 13
-#define WIRELESS_SPACE_FRONT_BUTTON 43
-
-const u32 kwmpp_config[] = {
- MPP0_NF_IO2,
- MPP1_NF_IO3,
- MPP2_NF_IO4,
- MPP3_NF_IO5,
- MPP4_NF_IO6,
- MPP5_NF_IO7,
- MPP6_SYSRST_OUTn,
- MPP7_GPO, /* Fan speed (bit 1) */
- MPP8_TW_SDA,
- MPP9_TW_SCK,
- MPP10_UART0_TXD,
- MPP11_UART0_RXD,
- MPP13_GPIO, /* Red led */
- MPP14_GPIO, /* USB fuse */
- MPP15_SATA0_ACTn,
- MPP16_GPIO, /* SATA 0 power */
- MPP17_GPIO, /* SATA 1 power */
- MPP18_NF_IO0,
- MPP19_NF_IO1,
- MPP20_GE1_0, /* Gigabit Ethernet 1 */
- MPP21_GE1_1,
- MPP22_GE1_2,
- MPP23_GE1_3,
- MPP24_GE1_4,
- MPP25_GE1_5,
- MPP26_GE1_6,
- MPP27_GE1_7,
- MPP28_GE1_8,
- MPP29_GE1_9,
- MPP30_GE1_10,
- MPP31_GE1_11,
- MPP32_GE1_12,
- MPP33_GE1_13,
- MPP34_GE1_14,
- MPP35_GE1_15,
- MPP36_GPIO, /* Fan speed (bit 2) */
- MPP37_GPIO, /* Fan speed (bit 0) */
- MPP38_GPIO, /* Fan power */
- MPP39_GPIO, /* Fan rotation fail */
- MPP40_GPIO, /* Ethernet switch link */
- MPP41_GPIO, /* USB enable host vbus */
- MPP42_GPIO, /* LED clock control */
- MPP43_GPIO, /* WPS button (0=Pushed, 1=Released) */
- MPP44_GPIO, /* Red LED on/off */
- MPP45_GPIO, /* Red LED timer blink (on=off=100ms) */
- MPP46_GPIO, /* Green LED on/off */
- MPP47_GPIO, /* LED (blue, green) SATA activity blink */
- MPP48_GPIO, /* Blue LED on/off */
- 0
-};
-
-struct mv88e61xx_config swcfg = {
- .name = "egiga0",
- .vlancfg = MV88E61XX_VLANCFG_ROUTER,
- .rgmii_delay = MV88E61XX_RGMII_DELAY_EN,
- .led_init = MV88E61XX_LED_INIT_EN,
- .mdip = MV88E61XX_MDIP_NOCHANGE,
- .portstate = MV88E61XX_PORTSTT_FORWARDING,
- .cpuport = 0x20,
- .ports_enabled = 0x3F,
-};
-
-int board_early_init_f(void)
-{
- /* Gpio configuration */
- mvebu_config_gpio(WIRELESS_SPACE_OE_VAL_LOW, WIRELESS_SPACE_OE_VAL_HIGH,
- WIRELESS_SPACE_OE_LOW, WIRELESS_SPACE_OE_HIGH);
-
- /* Multi-Purpose Pins Functionality configuration */
- kirkwood_mpp_conf(kwmpp_config, NULL);
-
- return 0;
-}
-
-int board_init(void)
-{
- /* Machine number */
- gd->bd->bi_arch_number = CONFIG_MACH_TYPE;
-
- /* Boot parameters address */
- gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100;
-
- return 0;
-}
-
-#if defined(CONFIG_MISC_INIT_R)
-int misc_init_r(void)
-{
-#if defined(CONFIG_CMD_I2C) && defined(CONFIG_SYS_I2C_EEPROM_ADDR)
- if (!getenv("ethaddr")) {
- uchar mac[6];
- if (lacie_read_mac_address(mac) == 0)
- eth_setenv_enetaddr("ethaddr", mac);
- }
-#endif
- return 0;
-}
-#endif
-
-#if defined(CONFIG_CMD_NET) && defined(CONFIG_RESET_PHY_R)
-/* Configure and initialize PHY */
-void reset_phy(void)
-{
- /* configure switch on egiga0 */
- mv88e61xx_switch_initialize(&swcfg);
-}
-#endif
-
-#if defined(CONFIG_KIRKWOOD_GPIO) && defined(CONFIG_WIRELESS_SPACE_CMD)
-/* Return GPIO button status */
-static int
-do_ws(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
-{
- if (strcmp(argv[1], "button") == 0) {
- if (strcmp(argv[2], "rear") == 0)
- /* invert GPIO result for intuitive while/until use */
- return !kw_gpio_get_value(WIRELESS_SPACE_REAR_BUTTON);
- else if (strcmp(argv[2], "front") == 0)
- return kw_gpio_get_value(WIRELESS_SPACE_FRONT_BUTTON);
- else
- return -1;
- } else {
- return -1;
- }
-}
-
-U_BOOT_CMD(ws, 3, 0, do_ws,
- "Return GPIO button status 0=off 1=on",
- "- ws button rear|front: test buttons' states\n"
-);
-#endif
+++ /dev/null
-CONFIG_ARM=y
-CONFIG_KIRKWOOD=y
-CONFIG_TARGET_WIRELESS_SPACE=y
-# CONFIG_CMD_IMLS is not set
-# CONFIG_CMD_FLASH is not set
-# CONFIG_CMD_SETEXPR is not set
+++ /dev/null
-/*
- * Copyright (C) 2011 Albert ARIBAUD <albert.u.boot@aribaud.net>
- *
- * Based on the netspace_v2 code which is
- * Copyright (C) 2011 Simon Guinot <sguinot@lacie.com>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#ifndef _CONFIG_WIRELESS_SPACE_H
-#define _CONFIG_WIRELESS_SPACE_H
-
-/*
- * Machine number definition
- */
-#define MACH_TYPE_WIRELESS_SPACE 2500 /* is missing in mach-types.h */
-#define CONFIG_MACH_TYPE MACH_TYPE_WIRELESS_SPACE
-#define CONFIG_IDENT_STRING " Wireless Space"
-
-/*
- * High Level Configuration Options (easy to change)
- */
-#define CONFIG_FEROCEON_88FR131 /* CPU Core subversion */
-/* SoC name */
-#define CONFIG_KW88F6281
-#define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */
-
-/*
- * Commands configuration
- */
-#define CONFIG_SYS_NO_FLASH /* no NOR or SPI flash */
-#define CONFIG_CMD_ENV
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_NAND
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IDE
-#define CONFIG_CMD_USB
-
-/*
- * Core clock definition
- */
-#define CONFIG_SYS_TCLK 166000000 /* 166MHz */
-
-/*
- * SDRAM configuration
- */
-#define CONFIG_NR_DRAM_BANKS 1
-
-/*
- * Different SDRAM configuration and size for some of the boards derived
- * from the Network Space v2
- */
-
-/*
- * mv-common.h should be defined after CMD configs since it used them
- * to enable certain macros
- */
-#include "mv-common.h"
-
-/* Remove or override few declarations from mv-common.h */
-#undef CONFIG_RBTREE
-#undef CONFIG_SYS_IDE_MAXBUS
-#undef CONFIG_SYS_IDE_MAXDEVICE
-#define CONFIG_SYS_IDE_MAXBUS 1
-#define CONFIG_SYS_IDE_MAXDEVICE 1
-
-/*
- * Ethernet Driver configuration
- */
-#ifdef CONFIG_CMD_NET
-#define CONFIG_MISC_INIT_R /* misc_init_r() initializes MAC address */
-#define CONFIG_MVGBE_PORTS {1, 0} /* enable only egiga0... */
-#define PORT_SERIAL_CONTROL_VALUE 0x00A4260E /* ... tied to the switch... */
-#define CONFIG_PHY_BASE_ADR 0xa /* ... through a 'fake' PHY */
-#define CONFIG_MII
-#undef CONFIG_SYS_FAULT_ECHO_LINK_DOWN
-#define CONFIG_NETCONSOLE
-#define CONFIG_MV88E61XX_SWITCH
-#define CONFIG_MV88E61XX_MULTICHIP_ADRMODE
-#define CONFIG_MV88E61XX_CMD
-#define CONFIG_CMD_TFTPPUT
-#endif /* CONFIG_CMD_NET */
-
-/*
- * SATA Driver configuration
- */
-#ifdef CONFIG_MVSATA_IDE
-#define CONFIG_SYS_ATA_IDE0_OFFSET MV_SATA_PORT0_OFFSET
-#endif /* CONFIG_MVSATA_IDE */
-
-/*
- * Enable GPI0 support
- */
-#define CONFIG_KIRKWOOD_GPIO
-
-/*
- * Enable I2C support
- */
-#ifdef CONFIG_CMD_I2C
-/* I2C EEPROM HT24LC04 (512B - 32 pages of 16 Bytes) */
-#define CONFIG_CMD_EEPROM
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 /* 16-byte page size */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* 8-bit device address */
-#endif /* CONFIG_CMD_I2C */
-
-/*
- * Partition support
- */
-#define CONFIG_DOS_PARTITION
-#define CONFIG_EFI_PARTITION
-
-/*
- * File systems support
- */
-#define CONFIG_CMD_EXT2
-#define CONFIG_CMD_FAT
-
-/*
- * Use the HUSH parser
- */
-#define CONFIG_SYS_HUSH_PARSER
-
-/*
- * Console configuration
- */
-#define CONFIG_CONSOLE_MUX
-#define CONFIG_SYS_CONSOLE_IS_IN_ENV
-
-/*
- * Enable device tree support
- */
-#define CONFIG_OF_LIBFDT
-
-/*
- * Environment variables configurations
- */
-
-#define CONFIG_ENV_IS_IN_NAND
-#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128KB */
-#define CONFIG_ENV_SIZE 0x20000 /* 128KB */
-#define CONFIG_ENV_OFFSET 0x80000 /* env starts here */
-
-/*
- * Board-specific command to make using buttons etc easier
- */
-
-#define CONFIG_WIRELESS_SPACE_CMD
-
-/*
- * Default environment variables
- */
-#define CONFIG_PREBOOT
-
-#define CONFIG_BOOTARGS "console=ttyS0,115200"
-
-#define CONFIG_BOOTCOMMAND \
- "if run usbload || run diskload; then bootm; fi"
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "stdin=serial\0" \
- "stdout=serial\0" \
- "stderr=serial\0" \
- "bootfile=uImage\0" \
- "loadaddr=0x800000\0" \
- "autoload=no\0" \
- "netconsole=" \
- "set stdin $stdin,nc; " \
- "set stdout $stdout,nc; " \
- "set stderr $stderr,nc;\0" \
- "diskload=ide reset && " \
- "ext2load ide 0:1 $loadaddr /boot/$bootfile\0" \
- "usbload=usb start && " \
- "fatload usb 0:1 $loadaddr /boot/$bootfile\0" \
- "preboot=" \
- "dhcp && run netconsole\0"
-
-#endif /* _CONFIG_WIRELESS_SPACE_H */
projects / platform / kernel / u-boot.git / commitdiff