--- /dev/null
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2022 MediaTek Inc. All Rights Reserved.
+ *
+ * Author: SkyLake.Huang <skylake.huang@mediatek.com>
+ */
+
+#include <clk.h>
+#include <cpu_func.h>
+#include <div64.h>
+#include <dm.h>
+#include <spi.h>
+#include <spi-mem.h>
+#include <stdbool.h>
+#include <watchdog.h>
+#include <dm/device.h>
+#include <dm/device_compat.h>
+#include <dm/devres.h>
+#include <dm/pinctrl.h>
+#include <linux/bitops.h>
+#include <linux/completion.h>
+#include <linux/dma-mapping.h>
+#include <linux/io.h>
+#include <linux/iopoll.h>
+
+#define SPI_CFG0_REG 0x0000
+#define SPI_CFG1_REG 0x0004
+#define SPI_TX_SRC_REG 0x0008
+#define SPI_RX_DST_REG 0x000c
+#define SPI_TX_DATA_REG 0x0010
+#define SPI_RX_DATA_REG 0x0014
+#define SPI_CMD_REG 0x0018
+#define SPI_IRQ_REG 0x001c
+#define SPI_STATUS_REG 0x0020
+#define SPI_PAD_SEL_REG 0x0024
+#define SPI_CFG2_REG 0x0028
+#define SPI_TX_SRC_REG_64 0x002c
+#define SPI_RX_DST_REG_64 0x0030
+#define SPI_CFG3_IPM_REG 0x0040
+
+#define SPI_CFG0_SCK_HIGH_OFFSET 0
+#define SPI_CFG0_SCK_LOW_OFFSET 8
+#define SPI_CFG0_CS_HOLD_OFFSET 16
+#define SPI_CFG0_CS_SETUP_OFFSET 24
+#define SPI_ADJUST_CFG0_CS_HOLD_OFFSET 0
+#define SPI_ADJUST_CFG0_CS_SETUP_OFFSET 16
+
+#define SPI_CFG1_CS_IDLE_OFFSET 0
+#define SPI_CFG1_PACKET_LOOP_OFFSET 8
+#define SPI_CFG1_PACKET_LENGTH_OFFSET 16
+#define SPI_CFG1_GET_TICKDLY_OFFSET 29
+
+#define SPI_CFG1_GET_TICKDLY_MASK GENMASK(31, 29)
+#define SPI_CFG1_CS_IDLE_MASK 0xff
+#define SPI_CFG1_PACKET_LOOP_MASK 0xff00
+#define SPI_CFG1_PACKET_LENGTH_MASK 0x3ff0000
+#define SPI_CFG1_IPM_PACKET_LENGTH_MASK GENMASK(31, 16)
+#define SPI_CFG2_SCK_HIGH_OFFSET 0
+#define SPI_CFG2_SCK_LOW_OFFSET 16
+#define SPI_CFG2_SCK_HIGH_MASK GENMASK(15, 0)
+#define SPI_CFG2_SCK_LOW_MASK GENMASK(31, 16)
+
+#define SPI_CMD_ACT BIT(0)
+#define SPI_CMD_RESUME BIT(1)
+#define SPI_CMD_RST BIT(2)
+#define SPI_CMD_PAUSE_EN BIT(4)
+#define SPI_CMD_DEASSERT BIT(5)
+#define SPI_CMD_SAMPLE_SEL BIT(6)
+#define SPI_CMD_CS_POL BIT(7)
+#define SPI_CMD_CPHA BIT(8)
+#define SPI_CMD_CPOL BIT(9)
+#define SPI_CMD_RX_DMA BIT(10)
+#define SPI_CMD_TX_DMA BIT(11)
+#define SPI_CMD_TXMSBF BIT(12)
+#define SPI_CMD_RXMSBF BIT(13)
+#define SPI_CMD_RX_ENDIAN BIT(14)
+#define SPI_CMD_TX_ENDIAN BIT(15)
+#define SPI_CMD_FINISH_IE BIT(16)
+#define SPI_CMD_PAUSE_IE BIT(17)
+#define SPI_CMD_IPM_NONIDLE_MODE BIT(19)
+#define SPI_CMD_IPM_SPIM_LOOP BIT(21)
+#define SPI_CMD_IPM_GET_TICKDLY_OFFSET 22
+
+#define SPI_CMD_IPM_GET_TICKDLY_MASK GENMASK(24, 22)
+
+#define PIN_MODE_CFG(x) ((x) / 2)
+
+#define SPI_CFG3_IPM_PIN_MODE_OFFSET 0
+#define SPI_CFG3_IPM_HALF_DUPLEX_DIR BIT(2)
+#define SPI_CFG3_IPM_HALF_DUPLEX_EN BIT(3)
+#define SPI_CFG3_IPM_XMODE_EN BIT(4)
+#define SPI_CFG3_IPM_NODATA_FLAG BIT(5)
+#define SPI_CFG3_IPM_CMD_BYTELEN_OFFSET 8
+#define SPI_CFG3_IPM_ADDR_BYTELEN_OFFSET 12
+#define SPI_CFG3_IPM_DUMMY_BYTELEN_OFFSET 16
+
+#define SPI_CFG3_IPM_CMD_PIN_MODE_MASK GENMASK(1, 0)
+#define SPI_CFG3_IPM_CMD_BYTELEN_MASK GENMASK(11, 8)
+#define SPI_CFG3_IPM_ADDR_BYTELEN_MASK GENMASK(15, 12)
+#define SPI_CFG3_IPM_DUMMY_BYTELEN_MASK GENMASK(19, 16)
+
+#define MT8173_SPI_MAX_PAD_SEL 3
+
+#define MTK_SPI_PAUSE_INT_STATUS 0x2
+
+#define MTK_SPI_IDLE 0
+#define MTK_SPI_PAUSED 1
+
+#define MTK_SPI_MAX_FIFO_SIZE 32U
+#define MTK_SPI_PACKET_SIZE 1024
+#define MTK_SPI_IPM_PACKET_SIZE SZ_64K
+#define MTK_SPI_IPM_PACKET_LOOP SZ_256
+
+#define MTK_SPI_32BITS_MASK 0xffffffff
+
+#define DMA_ADDR_EXT_BITS 36
+#define DMA_ADDR_DEF_BITS 32
+
+#define CLK_TO_US(freq, clkcnt) DIV_ROUND_UP((clkcnt), (freq) / 1000000)
+
+/* struct mtk_spim_capability
+ * @enhance_timing: Some IC design adjust cfg register to enhance time accuracy
+ * @dma_ext: Some IC support DMA addr extension
+ * @ipm_design: The IPM IP design improves some features, and supports dual/quad mode
+ * @support_quad: Whether quad mode is supported
+ */
+struct mtk_spim_capability {
+ bool enhance_timing;
+ bool dma_ext;
+ bool ipm_design;
+ bool support_quad;
+};
+
+/* struct mtk_spim_priv
+ * @base: Base address of the spi controller
+ * @state: Controller state
+ * @sel_clk: Pad clock
+ * @spi_clk: Core clock
+ * @xfer_len: Current length of data for transfer
+ * @hw_cap: Controller capabilities
+ * @tick_dly: Used to postpone SPI sampling time
+ * @sample_sel: Sample edge of MISO
+ * @dev: udevice of this spi controller
+ * @tx_dma: Tx DMA address
+ * @rx_dma: Rx DMA address
+ */
+struct mtk_spim_priv {
+ void __iomem *base;
+ u32 state;
+ struct clk sel_clk, spi_clk;
+ u32 xfer_len;
+ struct mtk_spim_capability hw_cap;
+ u32 tick_dly;
+ u32 sample_sel;
+
+ struct device *dev;
+ dma_addr_t tx_dma;
+ dma_addr_t rx_dma;
+};
+
+static void mtk_spim_reset(struct mtk_spim_priv *priv)
+{
+ /* set the software reset bit in SPI_CMD_REG. */
+ setbits_le32(priv->base + SPI_CMD_REG, SPI_CMD_RST);
+ clrbits_le32(priv->base + SPI_CMD_REG, SPI_CMD_RST);
+}
+
+static int mtk_spim_hw_init(struct spi_slave *slave)
+{
+ struct udevice *bus = dev_get_parent(slave->dev);
+ struct mtk_spim_priv *priv = dev_get_priv(bus);
+ u16 cpha, cpol;
+ u32 reg_val;
+
+ cpha = slave->mode & SPI_CPHA ? 1 : 0;
+ cpol = slave->mode & SPI_CPOL ? 1 : 0;
+
+ if (priv->hw_cap.enhance_timing) {
+ if (priv->hw_cap.ipm_design) {
+ /* CFG3 reg only used for spi-mem,
+ * here write to default value
+ */
+ writel(0x0, priv->base + SPI_CFG3_IPM_REG);
+ clrsetbits_le32(priv->base + SPI_CMD_REG,
+ SPI_CMD_IPM_GET_TICKDLY_MASK,
+ priv->tick_dly <<
+ SPI_CMD_IPM_GET_TICKDLY_OFFSET);
+ } else {
+ clrsetbits_le32(priv->base + SPI_CFG1_REG,
+ SPI_CFG1_GET_TICKDLY_MASK,
+ priv->tick_dly <<
+ SPI_CFG1_GET_TICKDLY_OFFSET);
+ }
+ }
+
+ reg_val = readl(priv->base + SPI_CMD_REG);
+ if (priv->hw_cap.ipm_design) {
+ /* SPI transfer without idle time until packet length done */
+ reg_val |= SPI_CMD_IPM_NONIDLE_MODE;
+ if (slave->mode & SPI_LOOP)
+ reg_val |= SPI_CMD_IPM_SPIM_LOOP;
+ else
+ reg_val &= ~SPI_CMD_IPM_SPIM_LOOP;
+ }
+
+ if (cpha)
+ reg_val |= SPI_CMD_CPHA;
+ else
+ reg_val &= ~SPI_CMD_CPHA;
+ if (cpol)
+ reg_val |= SPI_CMD_CPOL;
+ else
+ reg_val &= ~SPI_CMD_CPOL;
+
+ /* set the mlsbx and mlsbtx */
+ if (slave->mode & SPI_LSB_FIRST) {
+ reg_val &= ~SPI_CMD_TXMSBF;
+ reg_val &= ~SPI_CMD_RXMSBF;
+ } else {
+ reg_val |= SPI_CMD_TXMSBF;
+ reg_val |= SPI_CMD_RXMSBF;
+ }
+
+ /* do not reverse tx/rx endian */
+ reg_val &= ~SPI_CMD_TX_ENDIAN;
+ reg_val &= ~SPI_CMD_RX_ENDIAN;
+
+ if (priv->hw_cap.enhance_timing) {
+ /* set CS polarity */
+ if (slave->mode & SPI_CS_HIGH)
+ reg_val |= SPI_CMD_CS_POL;
+ else
+ reg_val &= ~SPI_CMD_CS_POL;
+
+ if (priv->sample_sel)
+ reg_val |= SPI_CMD_SAMPLE_SEL;
+ else
+ reg_val &= ~SPI_CMD_SAMPLE_SEL;
+ }
+
+ /* disable dma mode */
+ reg_val &= ~(SPI_CMD_TX_DMA | SPI_CMD_RX_DMA);
+
+ /* disable deassert mode */
+ reg_val &= ~SPI_CMD_DEASSERT;
+
+ writel(reg_val, priv->base + SPI_CMD_REG);
+
+ return 0;
+}
+
+static void mtk_spim_prepare_transfer(struct mtk_spim_priv *priv,
+ u32 speed_hz)
+{
+ u32 spi_clk_hz, div, sck_time, cs_time, reg_val;
+
+ spi_clk_hz = clk_get_rate(&priv->spi_clk);
+ if (speed_hz <= spi_clk_hz / 4)
+ div = DIV_ROUND_UP(spi_clk_hz, speed_hz);
+ else
+ div = 4;
+
+ sck_time = (div + 1) / 2;
+ cs_time = sck_time * 2;
+
+ if (priv->hw_cap.enhance_timing) {
+ reg_val = ((sck_time - 1) & 0xffff)
+ << SPI_CFG2_SCK_HIGH_OFFSET;
+ reg_val |= ((sck_time - 1) & 0xffff)
+ << SPI_CFG2_SCK_LOW_OFFSET;
+ writel(reg_val, priv->base + SPI_CFG2_REG);
+
+ reg_val = ((cs_time - 1) & 0xffff)
+ << SPI_ADJUST_CFG0_CS_HOLD_OFFSET;
+ reg_val |= ((cs_time - 1) & 0xffff)
+ << SPI_ADJUST_CFG0_CS_SETUP_OFFSET;
+ writel(reg_val, priv->base + SPI_CFG0_REG);
+ } else {
+ reg_val = ((sck_time - 1) & 0xff)
+ << SPI_CFG0_SCK_HIGH_OFFSET;
+ reg_val |= ((sck_time - 1) & 0xff) << SPI_CFG0_SCK_LOW_OFFSET;
+ reg_val |= ((cs_time - 1) & 0xff) << SPI_CFG0_CS_HOLD_OFFSET;
+ reg_val |= ((cs_time - 1) & 0xff) << SPI_CFG0_CS_SETUP_OFFSET;
+ writel(reg_val, priv->base + SPI_CFG0_REG);
+ }
+
+ reg_val = readl(priv->base + SPI_CFG1_REG);
+ reg_val &= ~SPI_CFG1_CS_IDLE_MASK;
+ reg_val |= ((cs_time - 1) & 0xff) << SPI_CFG1_CS_IDLE_OFFSET;
+ writel(reg_val, priv->base + SPI_CFG1_REG);
+}
+
+/**
+ * mtk_spim_setup_packet() - setup packet format.
+ * @priv: controller priv
+ *
+ * This controller sents/receives data in packets. The packet size is
+ * configurable.
+ *
+ * This function calculates the maximum packet size available for current
+ * data, and calculates the number of packets required to sent/receive data
+ * as much as possible.
+ */
+static void mtk_spim_setup_packet(struct mtk_spim_priv *priv)
+{
+ u32 packet_size, packet_loop, reg_val;
+
+ /* Calculate maximum packet size */
+ if (priv->hw_cap.ipm_design)
+ packet_size = min_t(u32,
+ priv->xfer_len,
+ MTK_SPI_IPM_PACKET_SIZE);
+ else
+ packet_size = min_t(u32,
+ priv->xfer_len,
+ MTK_SPI_PACKET_SIZE);
+
+ /* Calculates number of packets to sent/receive */
+ packet_loop = priv->xfer_len / packet_size;
+
+ reg_val = readl(priv->base + SPI_CFG1_REG);
+ if (priv->hw_cap.ipm_design)
+ reg_val &= ~SPI_CFG1_IPM_PACKET_LENGTH_MASK;
+ else
+ reg_val &= ~SPI_CFG1_PACKET_LENGTH_MASK;
+
+ reg_val |= (packet_size - 1) << SPI_CFG1_PACKET_LENGTH_OFFSET;
+
+ reg_val &= ~SPI_CFG1_PACKET_LOOP_MASK;
+
+ reg_val |= (packet_loop - 1) << SPI_CFG1_PACKET_LOOP_OFFSET;
+
+ writel(reg_val, priv->base + SPI_CFG1_REG);
+}
+
+static void mtk_spim_enable_transfer(struct mtk_spim_priv *priv)
+{
+ u32 cmd;
+
+ cmd = readl(priv->base + SPI_CMD_REG);
+ if (priv->state == MTK_SPI_IDLE)
+ cmd |= SPI_CMD_ACT;
+ else
+ cmd |= SPI_CMD_RESUME;
+ writel(cmd, priv->base + SPI_CMD_REG);
+}
+
+static bool mtk_spim_supports_op(struct spi_slave *slave,
+ const struct spi_mem_op *op)
+{
+ struct udevice *bus = dev_get_parent(slave->dev);
+ struct mtk_spim_priv *priv = dev_get_priv(bus);
+
+ if (op->cmd.buswidth == 0 || op->cmd.buswidth > 4 ||
+ op->addr.buswidth > 4 || op->dummy.buswidth > 4 ||
+ op->data.buswidth > 4)
+ return false;
+
+ if (!priv->hw_cap.support_quad && (op->cmd.buswidth > 2 ||
+ op->addr.buswidth > 2 || op->dummy.buswidth > 2 ||
+ op->data.buswidth > 2))
+ return false;
+
+ if (op->addr.nbytes && op->dummy.nbytes &&
+ op->addr.buswidth != op->dummy.buswidth)
+ return false;
+
+ if (op->addr.nbytes + op->dummy.nbytes > 16)
+ return false;
+
+ if (op->data.nbytes > MTK_SPI_IPM_PACKET_SIZE) {
+ if (op->data.nbytes / MTK_SPI_IPM_PACKET_SIZE >
+ MTK_SPI_IPM_PACKET_LOOP ||
+ op->data.nbytes % MTK_SPI_IPM_PACKET_SIZE != 0)
+ return false;
+ }
+
+ return true;
+}
+
+static void mtk_spim_setup_dma_xfer(struct mtk_spim_priv *priv,
+ const struct spi_mem_op *op)
+{
+ writel((u32)(priv->tx_dma & MTK_SPI_32BITS_MASK),
+ priv->base + SPI_TX_SRC_REG);
+
+ if (priv->hw_cap.dma_ext)
+ writel((u32)(priv->tx_dma >> 32),
+ priv->base + SPI_TX_SRC_REG_64);
+
+ if (op->data.dir == SPI_MEM_DATA_IN) {
+ writel((u32)(priv->rx_dma & MTK_SPI_32BITS_MASK),
+ priv->base + SPI_RX_DST_REG);
+
+ if (priv->hw_cap.dma_ext)
+ writel((u32)(priv->rx_dma >> 32),
+ priv->base + SPI_RX_DST_REG_64);
+ }
+}
+
+static int mtk_spim_transfer_wait(struct spi_slave *slave,
+ const struct spi_mem_op *op)
+{
+ struct udevice *bus = dev_get_parent(slave->dev);
+ struct mtk_spim_priv *priv = dev_get_priv(bus);
+ u32 sck_l, sck_h, spi_bus_clk, clk_count, reg;
+ ulong us = 1;
+ int ret = 0;
+
+ if (op->data.dir == SPI_MEM_NO_DATA)
+ clk_count = 32;
+ else
+ clk_count = op->data.nbytes;
+
+ spi_bus_clk = clk_get_rate(&priv->spi_clk);
+ sck_l = readl(priv->base + SPI_CFG2_REG) >> SPI_CFG2_SCK_LOW_OFFSET;
+ sck_h = readl(priv->base + SPI_CFG2_REG) & SPI_CFG2_SCK_HIGH_MASK;
+ do_div(spi_bus_clk, sck_l + sck_h + 2);
+
+ us = CLK_TO_US(spi_bus_clk, clk_count * 8);
+ us += 1000 * 1000; /* 1s tolerance */
+
+ if (us > UINT_MAX)
+ us = UINT_MAX;
+
+ ret = readl_poll_timeout(priv->base + SPI_STATUS_REG, reg,
+ reg & 0x1, us);
+ if (ret < 0) {
+ dev_err(priv->dev, "transfer timeout, val: 0x%lx\n", us);
+ return -ETIMEDOUT;
+ }
+
+ return 0;
+}
+
+static int mtk_spim_exec_op(struct spi_slave *slave,
+ const struct spi_mem_op *op)
+{
+ struct udevice *bus = dev_get_parent(slave->dev);
+ struct mtk_spim_priv *priv = dev_get_priv(bus);
+ u32 reg_val, nio = 1, tx_size;
+ char *tx_tmp_buf;
+ char *rx_tmp_buf;
+ int i, ret = 0;
+
+ mtk_spim_reset(priv);
+ mtk_spim_hw_init(slave);
+ mtk_spim_prepare_transfer(priv, slave->max_hz);
+
+ reg_val = readl(priv->base + SPI_CFG3_IPM_REG);
+ /* opcode byte len */
+ reg_val &= ~SPI_CFG3_IPM_CMD_BYTELEN_MASK;
+ reg_val |= 1 << SPI_CFG3_IPM_CMD_BYTELEN_OFFSET;
+
+ /* addr & dummy byte len */
+ if (op->addr.nbytes || op->dummy.nbytes)
+ reg_val |= (op->addr.nbytes + op->dummy.nbytes) <<
+ SPI_CFG3_IPM_ADDR_BYTELEN_OFFSET;
+
+ /* data byte len */
+ if (!op->data.nbytes) {
+ reg_val |= SPI_CFG3_IPM_NODATA_FLAG;
+ writel(0, priv->base + SPI_CFG1_REG);
+ } else {
+ reg_val &= ~SPI_CFG3_IPM_NODATA_FLAG;
+ priv->xfer_len = op->data.nbytes;
+ mtk_spim_setup_packet(priv);
+ }
+
+ if (op->addr.nbytes || op->dummy.nbytes) {
+ if (op->addr.buswidth == 1 || op->dummy.buswidth == 1)
+ reg_val |= SPI_CFG3_IPM_XMODE_EN;
+ else
+ reg_val &= ~SPI_CFG3_IPM_XMODE_EN;
+ }
+
+ if (op->addr.buswidth == 2 ||
+ op->dummy.buswidth == 2 ||
+ op->data.buswidth == 2)
+ nio = 2;
+ else if (op->addr.buswidth == 4 ||
+ op->dummy.buswidth == 4 ||
+ op->data.buswidth == 4)
+ nio = 4;
+
+ reg_val &= ~SPI_CFG3_IPM_CMD_PIN_MODE_MASK;
+ reg_val |= PIN_MODE_CFG(nio) << SPI_CFG3_IPM_PIN_MODE_OFFSET;
+
+ reg_val |= SPI_CFG3_IPM_HALF_DUPLEX_EN;
+ if (op->data.dir == SPI_MEM_DATA_IN)
+ reg_val |= SPI_CFG3_IPM_HALF_DUPLEX_DIR;
+ else
+ reg_val &= ~SPI_CFG3_IPM_HALF_DUPLEX_DIR;
+ writel(reg_val, priv->base + SPI_CFG3_IPM_REG);
+
+ tx_size = 1 + op->addr.nbytes + op->dummy.nbytes;
+ if (op->data.dir == SPI_MEM_DATA_OUT)
+ tx_size += op->data.nbytes;
+
+ tx_size = max(tx_size, (u32)32);
+
+ /* Fill up tx data */
+ tx_tmp_buf = kzalloc(tx_size, GFP_KERNEL);
+ if (!tx_tmp_buf) {
+ ret = -ENOMEM;
+ goto exit;
+ }
+
+ tx_tmp_buf[0] = op->cmd.opcode;
+
+ if (op->addr.nbytes) {
+ for (i = 0; i < op->addr.nbytes; i++)
+ tx_tmp_buf[i + 1] = op->addr.val >>
+ (8 * (op->addr.nbytes - i - 1));
+ }
+
+ if (op->dummy.nbytes)
+ memset(tx_tmp_buf + op->addr.nbytes + 1, 0xff,
+ op->dummy.nbytes);
+
+ if (op->data.nbytes && op->data.dir == SPI_MEM_DATA_OUT)
+ memcpy(tx_tmp_buf + op->dummy.nbytes + op->addr.nbytes + 1,
+ op->data.buf.out, op->data.nbytes);
+ /* Finish filling up tx data */
+
+ priv->tx_dma = dma_map_single(tx_tmp_buf, tx_size, DMA_TO_DEVICE);
+ if (dma_mapping_error(priv->dev, priv->tx_dma)) {
+ ret = -ENOMEM;
+ goto tx_free;
+ }
+
+ if (op->data.dir == SPI_MEM_DATA_IN) {
+ if (!IS_ALIGNED((size_t)op->data.buf.in, 4)) {
+ rx_tmp_buf = kzalloc(op->data.nbytes, GFP_KERNEL);
+ if (!rx_tmp_buf) {
+ ret = -ENOMEM;
+ goto tx_unmap;
+ }
+ } else {
+ rx_tmp_buf = op->data.buf.in;
+ }
+
+ priv->rx_dma = dma_map_single(rx_tmp_buf, op->data.nbytes,
+ DMA_FROM_DEVICE);
+ if (dma_mapping_error(priv->dev, priv->rx_dma)) {
+ ret = -ENOMEM;
+ goto rx_free;
+ }
+ }
+
+ reg_val = readl(priv->base + SPI_CMD_REG);
+ reg_val |= SPI_CMD_TX_DMA;
+ if (op->data.dir == SPI_MEM_DATA_IN)
+ reg_val |= SPI_CMD_RX_DMA;
+
+ writel(reg_val, priv->base + SPI_CMD_REG);
+
+ mtk_spim_setup_dma_xfer(priv, op);
+
+ mtk_spim_enable_transfer(priv);
+
+ /* Wait for the interrupt. */
+ ret = mtk_spim_transfer_wait(slave, op);
+ if (ret)
+ goto rx_unmap;
+
+ if (op->data.dir == SPI_MEM_DATA_IN &&
+ !IS_ALIGNED((size_t)op->data.buf.in, 4))
+ memcpy(op->data.buf.in, rx_tmp_buf, op->data.nbytes);
+
+rx_unmap:
+ /* spi disable dma */
+ reg_val = readl(priv->base + SPI_CMD_REG);
+ reg_val &= ~SPI_CMD_TX_DMA;
+ if (op->data.dir == SPI_MEM_DATA_IN)
+ reg_val &= ~SPI_CMD_RX_DMA;
+ writel(reg_val, priv->base + SPI_CMD_REG);
+
+ writel(0, priv->base + SPI_TX_SRC_REG);
+ writel(0, priv->base + SPI_RX_DST_REG);
+
+ if (op->data.dir == SPI_MEM_DATA_IN)
+ dma_unmap_single(priv->rx_dma,
+ op->data.nbytes, DMA_FROM_DEVICE);
+rx_free:
+ if (op->data.dir == SPI_MEM_DATA_IN &&
+ !IS_ALIGNED((size_t)op->data.buf.in, 4))
+ kfree(rx_tmp_buf);
+tx_unmap:
+ dma_unmap_single(priv->tx_dma,
+ tx_size, DMA_TO_DEVICE);
+tx_free:
+ kfree(tx_tmp_buf);
+exit:
+ return ret;
+}
+
+static int mtk_spim_adjust_op_size(struct spi_slave *slave,
+ struct spi_mem_op *op)
+{
+ int opcode_len;
+
+ if (!op->data.nbytes)
+ return 0;
+
+ if (op->data.dir != SPI_MEM_NO_DATA) {
+ opcode_len = 1 + op->addr.nbytes + op->dummy.nbytes;
+ if (opcode_len + op->data.nbytes > MTK_SPI_IPM_PACKET_SIZE) {
+ op->data.nbytes = MTK_SPI_IPM_PACKET_SIZE - opcode_len;
+ /* force data buffer dma-aligned. */
+ op->data.nbytes -= op->data.nbytes % 4;
+ }
+ }
+
+ return 0;
+}
+
+static int mtk_spim_get_attr(struct mtk_spim_priv *priv, struct udevice *dev)
+{
+ int ret;
+
+ priv->hw_cap.enhance_timing = dev_read_bool(dev, "enhance_timing");
+ priv->hw_cap.dma_ext = dev_read_bool(dev, "dma_ext");
+ priv->hw_cap.ipm_design = dev_read_bool(dev, "ipm_design");
+ priv->hw_cap.support_quad = dev_read_bool(dev, "support_quad");
+
+ ret = dev_read_u32(dev, "tick_dly", &priv->tick_dly);
+ if (ret < 0)
+ dev_err(priv->dev, "tick dly not set.\n");
+
+ ret = dev_read_u32(dev, "sample_sel", &priv->sample_sel);
+ if (ret < 0)
+ dev_err(priv->dev, "sample sel not set.\n");
+
+ return ret;
+}
+
+static int mtk_spim_probe(struct udevice *dev)
+{
+ struct mtk_spim_priv *priv = dev_get_priv(dev);
+ int ret;
+
+ priv->base = (void __iomem *)devfdt_get_addr(dev);
+ if (!priv->base)
+ return -EINVAL;
+
+ mtk_spim_get_attr(priv, dev);
+
+ ret = clk_get_by_name(dev, "sel-clk", &priv->sel_clk);
+ if (ret < 0) {
+ dev_err(dev, "failed to get sel-clk\n");
+ return ret;
+ }
+
+ ret = clk_get_by_name(dev, "spi-clk", &priv->spi_clk);
+ if (ret < 0) {
+ dev_err(dev, "failed to get spi-clk\n");
+ return ret;
+ }
+
+ clk_enable(&priv->sel_clk);
+ clk_enable(&priv->spi_clk);
+
+ return 0;
+}
+
+static int mtk_spim_set_speed(struct udevice *dev, uint speed)
+{
+ return 0;
+}
+
+static int mtk_spim_set_mode(struct udevice *dev, uint mode)
+{
+ return 0;
+}
+
+static const struct spi_controller_mem_ops mtk_spim_mem_ops = {
+ .adjust_op_size = mtk_spim_adjust_op_size,
+ .supports_op = mtk_spim_supports_op,
+ .exec_op = mtk_spim_exec_op
+};
+
+static const struct dm_spi_ops mtk_spim_ops = {
+ .mem_ops = &mtk_spim_mem_ops,
+ .set_speed = mtk_spim_set_speed,
+ .set_mode = mtk_spim_set_mode,
+};
+
+static const struct udevice_id mtk_spim_ids[] = {
+ { .compatible = "mediatek,ipm-spi" },
+ {}
+};
+
+U_BOOT_DRIVER(mtk_spim) = {
+ .name = "mtk_spim",
+ .id = UCLASS_SPI,
+ .of_match = mtk_spim_ids,
+ .ops = &mtk_spim_ops,
+ .priv_auto = sizeof(struct mtk_spim_priv),
+ .probe = mtk_spim_probe,
+};
projects / platform / kernel / u-boot.git / commitdiff