Aligning all block comments in extcon subsystem as per linux coding style.
Found using checkpatch.pl script.
Signed-off-by: Srikant Ritolia <s.ritolia@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
case MAX14577_IRQ_INT1_ADC:
case MAX14577_IRQ_INT1_ADCLOW:
case MAX14577_IRQ_INT1_ADCERR:
- /* Handle all of accessory except for
- type of charger accessory */
+ /*
+ * Handle all of accessory except for
+ * type of charger accessory.
+ */
info->irq_adc = true;
return 1;
case MAX14577_IRQ_INT2_CHGTYP:
MAX77693_MUIC_ADC_AUDIO_MODE_REMOTE,
MAX77693_MUIC_ADC_OPEN,
- /* The below accessories have same ADC value so ADCLow and
- ADC1K bit is used to separate specific accessory */
+ /*
+ * The below accessories have same ADC value so ADCLow and
+ * ADC1K bit is used to separate specific accessory.
+ */
/* ADC|VBVolot|ADCLow|ADC1K| */
MAX77693_MUIC_GND_USB_HOST = 0x100, /* 0x0| 0| 0| 0| */
MAX77693_MUIC_GND_USB_HOST_VB = 0x104, /* 0x0| 1| 0| 0| */
case MAX77693_MUIC_IRQ_INT1_ADC_LOW:
case MAX77693_MUIC_IRQ_INT1_ADC_ERR:
case MAX77693_MUIC_IRQ_INT1_ADC1K:
- /* Handle all of accessory except for
- type of charger accessory */
+ /*
+ * Handle all of accessory except for
+ * type of charger accessory.
+ */
ret = max77693_muic_adc_handler(info);
break;
case MAX77693_MUIC_IRQ_INT2_CHGTYP:
MAX77843_MUIC_ADC_AUDIO_DEVICE_TYPE1,
MAX77843_MUIC_ADC_OPEN,
- /* The blow accessories should check
- not only ADC value but also ADC1K and VBVolt value. */
+ /*
+ * The below accessories should check
+ * not only ADC value but also ADC1K and VBVolt value.
+ */
/* Offset|ADC1K|VBVolt| */
MAX77843_MUIC_GND_USB_HOST = 0x100, /* 0x1| 0| 0| */
MAX77843_MUIC_GND_USB_HOST_VB = 0x101, /* 0x1| 0| 1| */
/* Check GROUND accessory with charger cable */
if (adc == MAX77843_MUIC_ADC_GROUND) {
if (chg_type == MAX77843_MUIC_CHG_NONE) {
- /* The following state when charger cable is
+ /*
+ * The following state when charger cable is
* disconnected but the GROUND accessory still
- * connected */
+ * connected.
+ */
*attached = false;
cable_type = info->prev_chg_type;
info->prev_chg_type = MAX77843_MUIC_CHG_NONE;
} else {
- /* The following state when charger cable is
- * connected on the GROUND accessory */
+ /*
+ * The following state when charger cable is
+ * connected on the GROUND accessory.
+ */
*attached = true;
cable_type = MAX77843_MUIC_CHG_GND;
info->prev_chg_type = MAX77843_MUIC_CHG_GND;
} else {
*attached = true;
- /* Offset|ADC1K|VBVolt|
+ /*
+ * Offset|ADC1K|VBVolt|
* 0x1| 0| 0| USB-HOST
* 0x1| 0| 1| USB-HOST with VB
* 0x1| 1| 0| MHL
- * 0x1| 1| 1| MHL with VB */
+ * 0x1| 1| 1| MHL with VB
+ */
/* Get ADC1K register bit */
gnd_type = (info->status[MAX77843_MUIC_STATUS1] &
MAX77843_MUIC_STATUS1_ADC1K_MASK);
RT8973A_MUIC_ADC_UNKNOWN_ACC_5,
RT8973A_MUIC_ADC_OPEN = 0x1f,
- /* The below accessories has same ADC value (0x1f).
- So, Device type1 is used to separate specific accessory. */
+ /*
+ * The below accessories has same ADC value (0x1f).
+ * So, Device type1 is used to separate specific accessory.
+ */
/* |---------|--ADC| */
/* | [7:5]|[4:0]| */
RT8973A_MUIC_ADC_USB = 0x3f, /* | 001|11111| */
SM5502_MUIC_ADC_AUDIO_TYPE1,
SM5502_MUIC_ADC_OPEN = 0x1f,
- /* The below accessories have same ADC value (0x1f or 0x1e).
- So, Device type1 is used to separate specific accessory. */
+ /*
+ * The below accessories have same ADC value (0x1f or 0x1e).
+ * So, Device type1 is used to separate specific accessory.
+ */
/* |---------|--ADC| */
/* | [7:5]|[4:0]| */
SM5502_MUIC_ADC_AUDIO_TYPE1_FULL_REMOTE = 0x3e, /* | 001|11110| */