ipmi: add parameter to limit CPU usage in kipmid

In some cases kipmid can use a lot of CPU.  This adds a way to tune the
CPU used by kipmid to help in those cases.  By setting kipmid_max_busy_us
to a value between 100 and 500, it is possible to bring down kipmid CPU
load to practically 0 without loosing too much ipmi throughput
performance.  Not setting the value, or setting the value to zero,
operation is unaffected.

Signed-off-by: Martin Wilck <martin.wilck@ts.fujitsu.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Cc: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

diff --git a/Documentation/IPMI.txt b/Documentation/IPMI.txt
index bc38283..69dd29e 100644 (file)
--- a/Documentation/IPMI.txt
+++ b/Documentation/IPMI.txt
@@ -365,6 +365,7 @@ You can change this at module load time (for a module) with:
        regshifts=<shift1>,<shift2>,...
        slave_addrs=<addr1>,<addr2>,...
        force_kipmid=<enable1>,<enable2>,...
+       kipmid_max_busy_us=<ustime1>,<ustime2>,...
        unload_when_empty=[0|1]
 
 Each of these except si_trydefaults is a list, the first item for the
@@ -433,6 +434,7 @@ kernel command line as:
        ipmi_si.regshifts=<shift1>,<shift2>,...
        ipmi_si.slave_addrs=<addr1>,<addr2>,...
        ipmi_si.force_kipmid=<enable1>,<enable2>,...
+       ipmi_si.kipmid_max_busy_us=<ustime1>,<ustime2>,...
 
 It works the same as the module parameters of the same names.
 
@@ -450,6 +452,16 @@ force this thread on or off.  If you force it off and don't have
 interrupts, the driver will run VERY slowly.  Don't blame me,
 these interfaces suck.
 
+Unfortunately, this thread can use a lot of CPU depending on the
+interface's performance.  This can waste a lot of CPU and cause
+various issues with detecting idle CPU and using extra power.  To
+avoid this, the kipmid_max_busy_us sets the maximum amount of time, in
+microseconds, that kipmid will spin before sleeping for a tick.  This
+value sets a balance between performance and CPU waste and needs to be
+tuned to your needs.  Maybe, someday, auto-tuning will be added, but
+that's not a simple thing and even the auto-tuning would need to be
+tuned to the user's desired performance.
+
 The driver supports a hot add and remove of interfaces.  This way,
 interfaces can be added or removed after the kernel is up and running.
 This is done using /sys/modules/ipmi_si/parameters/hotmod, which is a

diff --git a/drivers/char/ipmi/ipmi_si_intf.c b/drivers/char/ipmi/ipmi_si_intf.c
index 176f175..c234ada 100644 (file)
--- a/drivers/char/ipmi/ipmi_si_intf.c
+++ b/drivers/char/ipmi/ipmi_si_intf.c
@@ -295,6 +295,9 @@ struct smi_info {
 static int force_kipmid[SI_MAX_PARMS];
 static int num_force_kipmid;
 
+static unsigned int kipmid_max_busy_us[SI_MAX_PARMS];
+static int num_max_busy_us;
+
 static int unload_when_empty = 1;
 
 static int try_smi_init(struct smi_info *smi);
@@ -925,23 +928,77 @@ static void set_run_to_completion(void *send_info, int i_run_to_completion)
        }
 }
 
+/*
+ * Use -1 in the nsec value of the busy waiting timespec to tell that
+ * we are spinning in kipmid looking for something and not delaying
+ * between checks
+ */
+static inline void ipmi_si_set_not_busy(struct timespec *ts)
+{
+       ts->tv_nsec = -1;
+}
+static inline int ipmi_si_is_busy(struct timespec *ts)
+{
+       return ts->tv_nsec != -1;
+}
+
+static int ipmi_thread_busy_wait(enum si_sm_result smi_result,
+                                const struct smi_info *smi_info,
+                                struct timespec *busy_until)
+{
+       unsigned int max_busy_us = 0;
+
+       if (smi_info->intf_num < num_max_busy_us)
+               max_busy_us = kipmid_max_busy_us[smi_info->intf_num];
+       if (max_busy_us == 0 || smi_result != SI_SM_CALL_WITH_DELAY)
+               ipmi_si_set_not_busy(busy_until);
+       else if (!ipmi_si_is_busy(busy_until)) {
+               getnstimeofday(busy_until);
+               timespec_add_ns(busy_until, max_busy_us*NSEC_PER_USEC);
+       } else {
+               struct timespec now;
+               getnstimeofday(&now);
+               if (unlikely(timespec_compare(&now, busy_until) > 0)) {
+                       ipmi_si_set_not_busy(busy_until);
+                       return 0;
+               }
+       }
+       return 1;
+}
+
+
+/*
+ * A busy-waiting loop for speeding up IPMI operation.
+ *
+ * Lousy hardware makes this hard.  This is only enabled for systems
+ * that are not BT and do not have interrupts.  It starts spinning
+ * when an operation is complete or until max_busy tells it to stop
+ * (if that is enabled).  See the paragraph on kimid_max_busy_us in
+ * Documentation/IPMI.txt for details.
+ */
 static int ipmi_thread(void *data)
 {
        struct smi_info *smi_info = data;
        unsigned long flags;
        enum si_sm_result smi_result;
+       struct timespec busy_until;
 
+       ipmi_si_set_not_busy(&busy_until);
        set_user_nice(current, 19);
        while (!kthread_should_stop()) {
+               int busy_wait;
+
                spin_lock_irqsave(&(smi_info->si_lock), flags);
                smi_result = smi_event_handler(smi_info, 0);
                spin_unlock_irqrestore(&(smi_info->si_lock), flags);
+               busy_wait = ipmi_thread_busy_wait(smi_result, smi_info,
+                                                 &busy_until);
                if (smi_result == SI_SM_CALL_WITHOUT_DELAY)
                        ; /* do nothing */
-               else if (smi_result == SI_SM_CALL_WITH_DELAY)
+               else if (smi_result == SI_SM_CALL_WITH_DELAY && busy_wait)
                        schedule();
                else
-                       schedule_timeout_interruptible(1);
+                       schedule_timeout_interruptible(0);
        }
        return 0;
 }
@@ -1212,6 +1269,11 @@ module_param(unload_when_empty, int, 0);
 MODULE_PARM_DESC(unload_when_empty, "Unload the module if no interfaces are"
                 " specified or found, default is 1.  Setting to 0"
                 " is useful for hot add of devices using hotmod.");
+module_param_array(kipmid_max_busy_us, uint, &num_max_busy_us, 0644);
+MODULE_PARM_DESC(kipmid_max_busy_us,
+                "Max time (in microseconds) to busy-wait for IPMI data before"
+                " sleeping. 0 (default) means to wait forever. Set to 100-500"
+                " if kipmid is using up a lot of CPU time.");
 
 
 static void std_irq_cleanup(struct smi_info *info)