Bug hunting
+++++++++++
-Last updated: 20 December 2005
+Last updated: 28 October 2016
Introduction
============
Devices not appearing
=====================
-Often this is caused by udev. Check that first before blaming it on the
-kernel.
+Often this is caused by udev/systemd. Check that first before blaming it
+on the kernel.
Finding patch that caused a bug
===============================
-
-
-Finding using ``git-bisect``
-----------------------------
-
Using the provided tools with ``git`` makes finding bugs easy provided the bug
is reproducible.
Steps to do it:
-- start using git for the kernel source
-- read the man page for ``git-bisect``
-- have fun
-
-Finding it the old way
-----------------------
-
-[Sat Mar 2 10:32:33 PST 1996 KERNEL_BUG-HOWTO lm@sgi.com (Larry McVoy)]
-
-This is how to track down a bug if you know nothing about kernel hacking.
-It's a brute force approach but it works pretty well.
-
-You need:
-
- - A reproducible bug - it has to happen predictably (sorry)
- - All the kernel tar files from a revision that worked to the
- revision that doesn't
-
-You will then do:
-
- - Rebuild a revision that you believe works, install, and verify that.
- - Do a binary search over the kernels to figure out which one
- introduced the bug. I.e., suppose 1.3.28 didn't have the bug, but
- you know that 1.3.69 does. Pick a kernel in the middle and build
- that, like 1.3.50. Build & test; if it works, pick the mid point
- between .50 and .69, else the mid point between .28 and .50.
- - You'll narrow it down to the kernel that introduced the bug. You
- can probably do better than this but it gets tricky.
+- build the Kernel from its git source
+- start bisect with [#f1]_::
- - Narrow it down to a subdirectory
+ $ git bisect start
- - Copy kernel that works into "test". Let's say that 3.62 works,
- but 3.63 doesn't. So you diff -r those two kernels and come
- up with a list of directories that changed. For each of those
- directories:
+- mark the broken changeset with::
- Copy the non-working directory next to the working directory
- as "dir.63".
- One directory at time, try moving the working directory to
- "dir.62" and mv dir.63 dir"time, try::
+ $ git bisect bad [commit]
- mv dir dir.62
- mv dir.63 dir
- find dir -name '*.[oa]' -print | xargs rm -f
+- mark a changeset where the code is known to work with::
- And then rebuild and retest. Assuming that all related
- changes were contained in the sub directory, this should
- isolate the change to a directory.
+ $ git bisect good [commit]
- Problems: changes in header files may have occurred; I've
- found in my case that they were self explanatory - you may
- or may not want to give up when that happens.
+- rebuild the Kernel and test
+- interact with git bisect by using either::
- - Narrow it down to a file
+ $ git bisect good
- - You can apply the same technique to each file in the directory,
- hoping that the changes in that file are self contained.
+ or::
- - Narrow it down to a routine
+ $ git bisect bad
- - You can take the old file and the new file and manually create
- a merged file that has::
+ depending if the bug happened on the changeset you're testing
+- After some interactions, git bisect will give you the changeset that
+ likely caused the bug.
- #ifdef VER62
- routine()
- {
- ...
- }
- #else
- routine()
- {
- ...
- }
- #endif
+- For example, if you know that the current version is bad, and version
+ 4.8 is good, you could do::
- And then walk through that file, one routine at a time and
- prefix it with::
+ $ git bisect start
+ $ git bisect bad # Current version is bad
+ $ git bisect good v4.8
- #define VER62
- /* both routines here */
- #undef VER62
- Then recompile, retest, move the ifdefs until you find the one
- that makes the difference.
+.. [#f1] You can, optionally, provide both good and bad arguments at git
+ start::
-Finally, you take all the info that you have, kernel revisions, bug
-description, the extent to which you have narrowed it down, and pass
-that off to whomever you believe is the maintainer of that section.
-A post to linux.dev.kernel isn't such a bad idea if you've done some
-work to narrow it down.
+ git bisect start [BAD] [GOOD]
-If you get it down to a routine, you'll probably get a fix in 24 hours.
+For further references, please read:
-My apologies to Linus and the other kernel hackers for describing this
-brute force approach, it's hardly what a kernel hacker would do. However,
-it does work and it lets non-hackers help fix bugs. And it is cool
-because Linux snapshots will let you do this - something that you can't
-do with vendor supplied releases.
+- The man page for ``git-bisect``
+- `Fighting regressions with git bisect <https://www.kernel.org/pub/software/scm/git/docs/git-bisect-lk2009.html>`_
+- `Fully automated bisecting with "git bisect run" <https://lwn.net/Articles/317154>`_
+- `Using Git bisect to figure out when brokenness was introduced <http://webchick.net/node/99>`_
Fixing the bug
==============
Nobody is going to tell you how to fix bugs. Seriously. You need to work it
out. But below are some hints on how to use the tools.
+objdump
+-------
+
To debug a kernel, use objdump and look for the hex offset from the crash
output to find the valid line of code/assembler. Without debug symbols, you
will see the assembler code for the routine shown, but if your kernel has
debug symbols the C code will also be available. (Debug symbols can be enabled
in the kernel hacking menu of the menu configuration.) For example::
- objdump -r -S -l --disassemble net/dccp/ipv4.o
+ $ objdump -r -S -l --disassemble net/dccp/ipv4.o
.. note::
If you don't have access to the code you can also debug on some crash dumps
e.g. crash dump output as shown by Dave Miller::
- EIP is at ip_queue_xmit+0x14/0x4c0
+ EIP is at +0x14/0x4c0
...
Code: 44 24 04 e8 6f 05 00 00 e9 e8 fe ff ff 8d 76 00 8d bc 27 00 00
00 00 55 57 56 53 81 ec bc 00 00 00 8b ac 24 d0 00 00 00 8b 5d 08
mov 0x8(%ebp), %ebx ! %ebx = skb->sk
mov 0x13c(%ebx), %eax ! %eax = inet_sk(sk)->opt
+gdb
+---
+
In addition, you can use GDB to figure out the exact file and line
-number of the OOPS from the ``vmlinux`` file. If you have
-``CONFIG_DEBUG_INFO`` enabled, you can simply copy the EIP value from the
-OOPS::
+number of the OOPS from the ``vmlinux`` file.
+
+The usage of gdb requires a kernel compiled with ``CONFIG_DEBUG_INFO``.
+This can be set by running::
+
+ $ ./scripts/config -d COMPILE_TEST -e DEBUG_KERNEL -e DEBUG_INFO
+
+On a kernel compiled with ``CONFIG_DEBUG_INFO``, you can simply copy the
+EIP value from the OOPS::
EIP: 0060:[<c021e50e>] Not tainted VLI
And use GDB to translate that to human-readable form::
- gdb vmlinux
+ $ gdb vmlinux
(gdb) l *0xc021e50e
If you don't have ``CONFIG_DEBUG_INFO`` enabled, you use the function
And recompile the kernel with ``CONFIG_DEBUG_INFO`` enabled::
- make vmlinux
- gdb vmlinux
+ $ make vmlinux
+ $ gdb vmlinux
+ (gdb) l *vt_ioctl+0xda8
+ 0x1888 is in vt_ioctl (drivers/tty/vt/vt_ioctl.c:293).
+ 288 {
+ 289 struct vc_data *vc = NULL;
+ 290 int ret = 0;
+ 291
+ 292 console_lock();
+ 293 if (VT_BUSY(vc_num))
+ 294 ret = -EBUSY;
+ 295 else if (vc_num)
+ 296 vc = vc_deallocate(vc_num);
+ 297 console_unlock();
+
+or, if you want to be more verbose::
+
(gdb) p vt_ioctl
- (gdb) l *(0x<address of vt_ioctl> + 0xda8)
+ $1 = {int (struct tty_struct *, unsigned int, unsigned long)} 0xae0 <vt_ioctl>
+ (gdb) l *0xae0+0xda8
-or, as one command::
+You could, instead, use the object file::
- (gdb) l *(vt_ioctl + 0xda8)
+ $ make drivers/tty/
+ $ gdb drivers/tty/vt/vt_ioctl.o
+ (gdb) l *vt_ioctl+0xda8
If you have a call trace, such as::
[<ffffffff8802770b>] :jbd:journal_stop+0x1be/0x1ee
...
-this shows the problem in the :jbd: module. You can load that module in gdb
-and list the relevant code::
-
- gdb fs/jbd/jbd.ko
- (gdb) p log_wait_commit
- (gdb) l *(0x<address> + 0xa3)
-
-or::
-
- (gdb) l *(log_wait_commit + 0xa3)
+this shows the problem likely in the :jbd: module. You can load that module
+in gdb and list the relevant code::
+ $ gdb fs/jbd/jbd.ko
+ (gdb) l *log_wait_commit+0xa3
Another very useful option of the Kernel Hacking section in menuconfig is
Debug memory allocations. This will help you see whether data has been
projects / platform / kernel / linux-starfive.git / commitdiff