bfin_write(®->clock, clk);
bfin_write(®->timing, timing);
- dev_info(dev->dev.parent, "setting CLOCK=0x%04x TIMING=0x%04x\n",
- clk, timing);
+ netdev_info(dev, "setting CLOCK=0x%04x TIMING=0x%04x\n", clk, timing);
return 0;
}
while (!(bfin_read(®->control) & CCA)) {
udelay(10);
if (--timeout == 0) {
- dev_err(dev->dev.parent,
- "fail to enter configuration mode\n");
+ netdev_err(dev, "fail to enter configuration mode\n");
BUG();
}
}
while (bfin_read(®->status) & CCA) {
udelay(10);
if (--timeout == 0) {
- dev_err(dev->dev.parent,
- "fail to leave configuration mode\n");
+ netdev_err(dev, "fail to leave configuration mode\n");
BUG();
}
}
if (isrc & RMLIS) {
/* data overrun interrupt */
- dev_dbg(dev->dev.parent, "data overrun interrupt\n");
+ netdev_dbg(dev, "data overrun interrupt\n");
cf->can_id |= CAN_ERR_CRTL;
cf->data[1] = CAN_ERR_CRTL_RX_OVERFLOW;
stats->rx_over_errors++;
}
if (isrc & BOIS) {
- dev_dbg(dev->dev.parent, "bus-off mode interrupt\n");
+ netdev_dbg(dev, "bus-off mode interrupt\n");
state = CAN_STATE_BUS_OFF;
cf->can_id |= CAN_ERR_BUSOFF;
can_bus_off(dev);
if (isrc & EPIS) {
/* error passive interrupt */
- dev_dbg(dev->dev.parent, "error passive interrupt\n");
+ netdev_dbg(dev, "error passive interrupt\n");
state = CAN_STATE_ERROR_PASSIVE;
}
if ((isrc & EWTIS) || (isrc & EWRIS)) {
- dev_dbg(dev->dev.parent,
- "Error Warning Transmit/Receive Interrupt\n");
+ netdev_dbg(dev, "Error Warning Transmit/Receive Interrupt\n");
state = CAN_STATE_ERROR_WARNING;
}
while (!(bfin_read(®->intr) & SMACK)) {
udelay(10);
if (--timeout == 0) {
- dev_err(dev->dev.parent,
- "fail to enter sleep mode\n");
+ netdev_err(dev, "fail to enter sleep mode\n");
BUG();
}
}
/* Error in one-tenth of a percent */
error = (best_error * 1000) / bt->bitrate;
if (error > CAN_CALC_MAX_ERROR) {
- dev_err(dev->dev.parent,
- "bitrate error %ld.%ld%% too high\n",
- error / 10, error % 10);
+ netdev_err(dev,
+ "bitrate error %ld.%ld%% too high\n",
+ error / 10, error % 10);
return -EDOM;
} else {
- dev_warn(dev->dev.parent, "bitrate error %ld.%ld%%\n",
- error / 10, error % 10);
+ netdev_warn(dev, "bitrate error %ld.%ld%%\n",
+ error / 10, error % 10);
}
}
#else /* !CONFIG_CAN_CALC_BITTIMING */
static int can_calc_bittiming(struct net_device *dev, struct can_bittiming *bt)
{
- dev_err(dev->dev.parent, "bit-timing calculation not available\n");
+ netdev_err(dev, "bit-timing calculation not available\n");
return -EINVAL;
}
#endif /* CONFIG_CAN_CALC_BITTIMING */
priv->echo_skb[idx] = skb;
} else {
/* locking problem with netif_stop_queue() ?? */
- dev_err(dev->dev.parent, "%s: BUG! echo_skb is occupied!\n",
- __func__);
+ netdev_err(dev, "%s: BUG! echo_skb is occupied!\n", __func__);
kfree_skb(skb);
}
}
stats->rx_bytes += cf->can_dlc;
restart:
- dev_dbg(dev->dev.parent, "restarted\n");
+ netdev_dbg(dev, "restarted\n");
priv->can_stats.restarts++;
/* Now restart the device */
netif_carrier_on(dev);
if (err)
- dev_err(dev->dev.parent, "Error %d during restart", err);
+ netdev_err(dev, "Error %d during restart", err);
}
int can_restart_now(struct net_device *dev)
{
struct can_priv *priv = netdev_priv(dev);
- dev_dbg(dev->dev.parent, "bus-off\n");
+ netdev_dbg(dev, "bus-off\n");
netif_carrier_off(dev);
priv->can_stats.bus_off++;
struct can_priv *priv = netdev_priv(dev);
if (!priv->bittiming.tq && !priv->bittiming.bitrate) {
- dev_err(dev->dev.parent, "bit-timing not yet defined\n");
+ netdev_err(dev, "bit-timing not yet defined\n");
return -EINVAL;
}
cf->can_id |= CAN_ERR_PROT | CAN_ERR_BUSERROR;
if (reg_esr & FLEXCAN_ESR_BIT1_ERR) {
- dev_dbg(dev->dev.parent, "BIT1_ERR irq\n");
+ netdev_dbg(dev, "BIT1_ERR irq\n");
cf->data[2] |= CAN_ERR_PROT_BIT1;
tx_errors = 1;
}
if (reg_esr & FLEXCAN_ESR_BIT0_ERR) {
- dev_dbg(dev->dev.parent, "BIT0_ERR irq\n");
+ netdev_dbg(dev, "BIT0_ERR irq\n");
cf->data[2] |= CAN_ERR_PROT_BIT0;
tx_errors = 1;
}
if (reg_esr & FLEXCAN_ESR_ACK_ERR) {
- dev_dbg(dev->dev.parent, "ACK_ERR irq\n");
+ netdev_dbg(dev, "ACK_ERR irq\n");
cf->can_id |= CAN_ERR_ACK;
cf->data[3] |= CAN_ERR_PROT_LOC_ACK;
tx_errors = 1;
}
if (reg_esr & FLEXCAN_ESR_CRC_ERR) {
- dev_dbg(dev->dev.parent, "CRC_ERR irq\n");
+ netdev_dbg(dev, "CRC_ERR irq\n");
cf->data[2] |= CAN_ERR_PROT_BIT;
cf->data[3] |= CAN_ERR_PROT_LOC_CRC_SEQ;
rx_errors = 1;
}
if (reg_esr & FLEXCAN_ESR_FRM_ERR) {
- dev_dbg(dev->dev.parent, "FRM_ERR irq\n");
+ netdev_dbg(dev, "FRM_ERR irq\n");
cf->data[2] |= CAN_ERR_PROT_FORM;
rx_errors = 1;
}
if (reg_esr & FLEXCAN_ESR_STF_ERR) {
- dev_dbg(dev->dev.parent, "STF_ERR irq\n");
+ netdev_dbg(dev, "STF_ERR irq\n");
cf->data[2] |= CAN_ERR_PROT_STUFF;
rx_errors = 1;
}
*/
if (new_state >= CAN_STATE_ERROR_WARNING &&
new_state <= CAN_STATE_BUS_OFF) {
- dev_dbg(dev->dev.parent, "Error Warning IRQ\n");
+ netdev_dbg(dev, "Error Warning IRQ\n");
priv->can.can_stats.error_warning++;
cf->can_id |= CAN_ERR_CRTL;
*/
if (new_state >= CAN_STATE_ERROR_PASSIVE &&
new_state <= CAN_STATE_BUS_OFF) {
- dev_dbg(dev->dev.parent, "Error Passive IRQ\n");
+ netdev_dbg(dev, "Error Passive IRQ\n");
priv->can.can_stats.error_passive++;
cf->can_id |= CAN_ERR_CRTL;
}
break;
case CAN_STATE_BUS_OFF:
- dev_err(dev->dev.parent,
- "BUG! hardware recovered automatically from BUS_OFF\n");
+ netdev_err(dev, "BUG! "
+ "hardware recovered automatically from BUS_OFF\n");
break;
default:
break;
/* process state changes depending on the new state */
switch (new_state) {
case CAN_STATE_ERROR_ACTIVE:
- dev_dbg(dev->dev.parent, "Error Active\n");
+ netdev_dbg(dev, "Error Active\n");
cf->can_id |= CAN_ERR_PROT;
cf->data[2] = CAN_ERR_PROT_ACTIVE;
break;
if (priv->can.ctrlmode & CAN_CTRLMODE_3_SAMPLES)
reg |= FLEXCAN_CTRL_SMP;
- dev_info(dev->dev.parent, "writing ctrl=0x%08x\n", reg);
+ netdev_info(dev, "writing ctrl=0x%08x\n", reg);
flexcan_write(reg, ®s->ctrl);
/* print chip status */
- dev_dbg(dev->dev.parent, "%s: mcr=0x%08x ctrl=0x%08x\n", __func__,
- flexcan_read(®s->mcr), flexcan_read(®s->ctrl));
+ netdev_dbg(dev, "%s: mcr=0x%08x ctrl=0x%08x\n", __func__,
+ flexcan_read(®s->mcr), flexcan_read(®s->ctrl));
}
/*
reg_mcr = flexcan_read(®s->mcr);
if (reg_mcr & FLEXCAN_MCR_SOFTRST) {
- dev_err(dev->dev.parent,
- "Failed to softreset can module (mcr=0x%08x)\n",
- reg_mcr);
+ netdev_err(dev, "Failed to softreset can module (mcr=0x%08x)\n",
+ reg_mcr);
err = -ENODEV;
goto out;
}
reg_mcr |= FLEXCAN_MCR_FRZ | FLEXCAN_MCR_FEN | FLEXCAN_MCR_HALT |
FLEXCAN_MCR_SUPV | FLEXCAN_MCR_WRN_EN |
FLEXCAN_MCR_IDAM_C | FLEXCAN_MCR_SRX_DIS;
- dev_dbg(dev->dev.parent, "%s: writing mcr=0x%08x", __func__, reg_mcr);
+ netdev_dbg(dev, "%s: writing mcr=0x%08x", __func__, reg_mcr);
flexcan_write(reg_mcr, ®s->mcr);
/*
/* save for later use */
priv->reg_ctrl_default = reg_ctrl;
- dev_dbg(dev->dev.parent, "%s: writing ctrl=0x%08x", __func__, reg_ctrl);
+ netdev_dbg(dev, "%s: writing ctrl=0x%08x", __func__, reg_ctrl);
flexcan_write(reg_ctrl, ®s->ctrl);
for (i = 0; i < ARRAY_SIZE(regs->cantxfg); i++) {
flexcan_write(FLEXCAN_IFLAG_DEFAULT, ®s->imask1);
/* print chip status */
- dev_dbg(dev->dev.parent, "%s: reading mcr=0x%08x ctrl=0x%08x\n",
- __func__, flexcan_read(®s->mcr), flexcan_read(®s->ctrl));
+ netdev_dbg(dev, "%s: reading mcr=0x%08x ctrl=0x%08x\n", __func__,
+ flexcan_read(®s->mcr), flexcan_read(®s->ctrl));
return 0;
*/
reg = flexcan_read(®s->mcr);
if (!(reg & FLEXCAN_MCR_FEN)) {
- dev_err(dev->dev.parent,
- "Could not enable RX FIFO, unsupported core\n");
+ netdev_err(dev, "Could not enable RX FIFO, unsupported core\n");
err = -ENODEV;
goto out;
}
frame->data[1] = data1;
netif_rx_ni(skb);
} else {
- dev_err(&net->dev,
- "cannot allocate error skb\n");
+ netdev_err(net, "cannot allocate error skb\n");
}
}
* any, at once.
*/
if (i >= MSCAN_SET_MODE_RETRIES)
- dev_dbg(dev->dev.parent,
- "device failed to enter sleep mode. "
- "We proceed anyhow.\n");
+ netdev_dbg(dev,
+ "device failed to enter sleep mode. "
+ "We proceed anyhow.\n");
else
priv->can.state = CAN_STATE_SLEEPING;
}
switch (hweight8(i)) {
case 0:
netif_stop_queue(dev);
- dev_err(dev->dev.parent, "Tx Ring full when queue awake!\n");
+ netdev_err(dev, "Tx Ring full when queue awake!\n");
return NETDEV_TX_BUSY;
case 1:
/*
struct net_device_stats *stats = &dev->stats;
enum can_state old_state;
- dev_dbg(dev->dev.parent, "error interrupt (canrflg=%#x)\n", canrflg);
+ netdev_dbg(dev, "error interrupt (canrflg=%#x)\n", canrflg);
frame->can_id = CAN_ERR_FLAG;
if (canrflg & MSCAN_OVRIF) {
skb = alloc_can_skb(dev, &frame);
if (!skb) {
if (printk_ratelimit())
- dev_notice(dev->dev.parent, "packet dropped\n");
+ netdev_notice(dev, "packet dropped\n");
stats->rx_dropped++;
out_8(®s->canrflg, canrflg);
continue;
BTR1_SET_TSEG2(bt->phase_seg2) |
BTR1_SET_SAM(priv->can.ctrlmode & CAN_CTRLMODE_3_SAMPLES));
- dev_info(dev->dev.parent, "setting BTR0=0x%02x BTR1=0x%02x\n",
- btr0, btr1);
+ netdev_info(dev, "setting BTR0=0x%02x BTR1=0x%02x\n", btr0, btr1);
out_8(®s->canbtr0, btr0);
out_8(®s->canbtr1, btr1);
ret = request_irq(dev->irq, mscan_isr, 0, dev->name, dev);
if (ret < 0) {
- dev_err(dev->dev.parent, "failed to attach interrupt\n");
+ netdev_err(dev, "failed to attach interrupt\n");
goto exit_napi_disable;
}
status = priv->read_reg(priv, REG_MOD);
}
- dev_err(dev->dev.parent, "setting SJA1000 into reset mode failed!\n");
+ netdev_err(dev, "setting SJA1000 into reset mode failed!\n");
}
static void set_normal_mode(struct net_device *dev)
status = priv->read_reg(priv, REG_MOD);
}
- dev_err(dev->dev.parent, "setting SJA1000 into normal mode failed!\n");
+ netdev_err(dev, "setting SJA1000 into normal mode failed!\n");
}
static void sja1000_start(struct net_device *dev)
if (priv->can.ctrlmode & CAN_CTRLMODE_3_SAMPLES)
btr1 |= 0x80;
- dev_info(dev->dev.parent,
- "setting BTR0=0x%02x BTR1=0x%02x\n", btr0, btr1);
+ netdev_info(dev, "setting BTR0=0x%02x BTR1=0x%02x\n", btr0, btr1);
priv->write_reg(priv, REG_BTR0, btr0);
priv->write_reg(priv, REG_BTR1, btr1);
if (isrc & IRQ_DOI) {
/* data overrun interrupt */
- dev_dbg(dev->dev.parent, "data overrun interrupt\n");
+ netdev_dbg(dev, "data overrun interrupt\n");
cf->can_id |= CAN_ERR_CRTL;
cf->data[1] = CAN_ERR_CRTL_RX_OVERFLOW;
stats->rx_over_errors++;
if (isrc & IRQ_EI) {
/* error warning interrupt */
- dev_dbg(dev->dev.parent, "error warning interrupt\n");
+ netdev_dbg(dev, "error warning interrupt\n");
if (status & SR_BS) {
state = CAN_STATE_BUS_OFF;
}
if (isrc & IRQ_EPI) {
/* error passive interrupt */
- dev_dbg(dev->dev.parent, "error passive interrupt\n");
+ netdev_dbg(dev, "error passive interrupt\n");
if (status & SR_ES)
state = CAN_STATE_ERROR_PASSIVE;
else
}
if (isrc & IRQ_ALI) {
/* arbitration lost interrupt */
- dev_dbg(dev->dev.parent, "arbitration lost interrupt\n");
+ netdev_dbg(dev, "arbitration lost interrupt\n");
alc = priv->read_reg(priv, REG_ALC);
priv->can.can_stats.arbitration_lost++;
stats->tx_errors++;
status = priv->read_reg(priv, REG_SR);
if (isrc & IRQ_WUI)
- dev_warn(dev->dev.parent, "wakeup interrupt\n");
+ netdev_warn(dev, "wakeup interrupt\n");
if (isrc & IRQ_TI) {
/* transmission complete interrupt */
priv->post_irq(priv);
if (n >= SJA1000_MAX_IRQ)
- dev_dbg(dev->dev.parent, "%d messages handled in ISR", n);
+ netdev_dbg(dev, "%d messages handled in ISR", n);
return (n) ? IRQ_HANDLED : IRQ_NONE;
}
if (bit_timing->brp > 4)
can_btc |= HECC_CANBTC_SAM;
else
- dev_warn(priv->ndev->dev.parent, "WARN: Triple" \
+ netdev_warn(priv->ndev, "WARN: Triple"
"sampling not set due to h/w limitations");
}
can_btc |= ((bit_timing->sjw - 1) & 0x3) << 8;
/* ERM being set to 0 by default meaning resync at falling edge */
hecc_write(priv, HECC_CANBTC, can_btc);
- dev_info(priv->ndev->dev.parent, "setting CANBTC=%#x\n", can_btc);
+ netdev_info(priv->ndev, "setting CANBTC=%#x\n", can_btc);
return 0;
}
u32 cnt;
struct ti_hecc_priv *priv = netdev_priv(ndev);
- dev_dbg(ndev->dev.parent, "resetting hecc ...\n");
+ netdev_dbg(ndev, "resetting hecc ...\n");
hecc_set_bit(priv, HECC_CANMC, HECC_CANMC_SRES);
/* Set change control request and wait till enabled */
if (unlikely(hecc_read(priv, HECC_CANME) & mbx_mask)) {
spin_unlock_irqrestore(&priv->mbx_lock, flags);
netif_stop_queue(ndev);
- dev_err(priv->ndev->dev.parent,
+ netdev_err(priv->ndev,
"BUG: TX mbx not ready tx_head=%08X, tx_tail=%08X\n",
priv->tx_head, priv->tx_tail);
return NETDEV_TX_BUSY;
skb = alloc_can_skb(priv->ndev, &cf);
if (!skb) {
if (printk_ratelimit())
- dev_err(priv->ndev->dev.parent,
+ netdev_err(priv->ndev,
"ti_hecc_rx_pkt: alloc_can_skb() failed\n");
return -ENOMEM;
}
skb = alloc_can_err_skb(ndev, &cf);
if (!skb) {
if (printk_ratelimit())
- dev_err(priv->ndev->dev.parent,
+ netdev_err(priv->ndev,
"ti_hecc_error: alloc_can_err_skb() failed\n");
return -ENOMEM;
}
cf->data[1] |= CAN_ERR_CRTL_RX_WARNING;
}
hecc_set_bit(priv, HECC_CANES, HECC_CANES_EW);
- dev_dbg(priv->ndev->dev.parent, "Error Warning interrupt\n");
+ netdev_dbg(priv->ndev, "Error Warning interrupt\n");
hecc_clear_bit(priv, HECC_CANMC, HECC_CANMC_CCR);
}
cf->data[1] |= CAN_ERR_CRTL_RX_PASSIVE;
}
hecc_set_bit(priv, HECC_CANES, HECC_CANES_EP);
- dev_dbg(priv->ndev->dev.parent, "Error passive interrupt\n");
+ netdev_dbg(priv->ndev, "Error passive interrupt\n");
hecc_clear_bit(priv, HECC_CANMC, HECC_CANMC_CCR);
}
err = request_irq(ndev->irq, ti_hecc_interrupt, IRQF_SHARED,
ndev->name, ndev);
if (err) {
- dev_err(ndev->dev.parent, "error requesting interrupt\n");
+ netdev_err(ndev, "error requesting interrupt\n");
return err;
}
/* Open common can device */
err = open_candev(ndev);
if (err) {
- dev_err(ndev->dev.parent, "open_candev() failed %d\n", err);
+ netdev_err(ndev, "open_candev() failed %d\n", err);
ti_hecc_transceiver_switch(priv, 0);
free_irq(ndev->irq, ndev);
return err;
return;
default:
- dev_info(netdev->dev.parent, "Rx interrupt aborted %d\n",
- urb->status);
+ netdev_info(netdev, "Rx interrupt aborted %d\n", urb->status);
break;
}
if (err == -ENODEV)
netif_device_detach(netdev);
else if (err)
- dev_err(netdev->dev.parent,
- "failed resubmitting intr urb: %d\n", err);
+ netdev_err(netdev, "failed resubmitting intr urb: %d\n", err);
}
static void ems_usb_rx_can_msg(struct ems_usb *dev, struct ems_cpc_msg *msg)
return;
default:
- dev_info(netdev->dev.parent, "Rx URB aborted (%d)\n",
- urb->status);
+ netdev_info(netdev, "Rx URB aborted (%d)\n", urb->status);
goto resubmit_urb;
}
msg_count--;
if (start > urb->transfer_buffer_length) {
- dev_err(netdev->dev.parent, "format error\n");
+ netdev_err(netdev, "format error\n");
break;
}
}
if (retval == -ENODEV)
netif_device_detach(netdev);
else if (retval)
- dev_err(netdev->dev.parent,
- "failed resubmitting read bulk urb: %d\n", retval);
+ netdev_err(netdev,
+ "failed resubmitting read bulk urb: %d\n", retval);
}
/*
return;
if (urb->status)
- dev_info(netdev->dev.parent, "Tx URB aborted (%d)\n",
- urb->status);
+ netdev_info(netdev, "Tx URB aborted (%d)\n", urb->status);
netdev->trans_start = jiffies;
/* create a URB, and a buffer for it */
urb = usb_alloc_urb(0, GFP_KERNEL);
if (!urb) {
- dev_err(netdev->dev.parent,
- "No memory left for URBs\n");
+ netdev_err(netdev, "No memory left for URBs\n");
err = -ENOMEM;
break;
}
buf = usb_alloc_coherent(dev->udev, RX_BUFFER_SIZE, GFP_KERNEL,
&urb->transfer_dma);
if (!buf) {
- dev_err(netdev->dev.parent,
- "No memory left for USB buffer\n");
+ netdev_err(netdev, "No memory left for USB buffer\n");
usb_free_urb(urb);
err = -ENOMEM;
break;
/* Did we submit any URBs */
if (i == 0) {
- dev_warn(netdev->dev.parent, "couldn't setup read URBs\n");
+ netdev_warn(netdev, "couldn't setup read URBs\n");
return err;
}
/* Warn if we've couldn't transmit all the URBs */
if (i < MAX_RX_URBS)
- dev_warn(netdev->dev.parent, "rx performance may be slow\n");
+ netdev_warn(netdev, "rx performance may be slow\n");
/* Setup and start interrupt URB */
usb_fill_int_urb(dev->intr_urb, dev->udev,
err = usb_submit_urb(dev->intr_urb, GFP_KERNEL);
if (err) {
- dev_warn(netdev->dev.parent, "intr URB submit failed: %d\n",
- err);
+ netdev_warn(netdev, "intr URB submit failed: %d\n", err);
return err;
}
return 0;
failed:
- dev_warn(netdev->dev.parent, "couldn't submit control: %d\n", err);
+ netdev_warn(netdev, "couldn't submit control: %d\n", err);
return err;
}
if (err == -ENODEV)
netif_device_detach(dev->netdev);
- dev_warn(netdev->dev.parent, "couldn't start device: %d\n",
- err);
+ netdev_warn(netdev, "couldn't start device: %d\n", err);
close_candev(netdev);
/* create a URB, and a buffer for it, and copy the data to the URB */
urb = usb_alloc_urb(0, GFP_ATOMIC);
if (!urb) {
- dev_err(netdev->dev.parent, "No memory left for URBs\n");
+ netdev_err(netdev, "No memory left for URBs\n");
goto nomem;
}
buf = usb_alloc_coherent(dev->udev, size, GFP_ATOMIC, &urb->transfer_dma);
if (!buf) {
- dev_err(netdev->dev.parent, "No memory left for USB buffer\n");
+ netdev_err(netdev, "No memory left for USB buffer\n");
usb_free_urb(urb);
goto nomem;
}
usb_unanchor_urb(urb);
usb_free_coherent(dev->udev, size, buf, urb->transfer_dma);
- dev_warn(netdev->dev.parent, "couldn't find free context\n");
+ netdev_warn(netdev, "couldn't find free context\n");
return NETDEV_TX_BUSY;
}
if (err == -ENODEV) {
netif_device_detach(netdev);
} else {
- dev_warn(netdev->dev.parent, "failed tx_urb %d\n", err);
+ netdev_warn(netdev, "failed tx_urb %d\n", err);
stats->tx_dropped++;
}
/* Set CAN controller to reset mode */
if (ems_usb_write_mode(dev, SJA1000_MOD_RM))
- dev_warn(netdev->dev.parent, "couldn't stop device");
+ netdev_warn(netdev, "couldn't stop device");
close_candev(netdev);
switch (mode) {
case CAN_MODE_START:
if (ems_usb_write_mode(dev, SJA1000_MOD_NORMAL))
- dev_warn(netdev->dev.parent, "couldn't start device");
+ netdev_warn(netdev, "couldn't start device");
if (netif_queue_stopped(netdev))
netif_wake_queue(netdev);
if (dev->can.ctrlmode & CAN_CTRLMODE_3_SAMPLES)
btr1 |= 0x80;
- dev_info(netdev->dev.parent, "setting BTR0=0x%02x BTR1=0x%02x\n",
- btr0, btr1);
+ netdev_info(netdev, "setting BTR0=0x%02x BTR1=0x%02x\n", btr0, btr1);
dev->active_params.msg.can_params.cc_params.sja1000.btr0 = btr0;
dev->active_params.msg.can_params.cc_params.sja1000.btr1 = btr1;
err = ems_usb_command_msg(dev, &dev->active_params);
if (err) {
- dev_err(netdev->dev.parent,
- "couldn't initialize controller: %d\n", err);
+ netdev_err(netdev, "couldn't initialize controller: %d\n", err);
goto cleanup_tx_msg_buffer;
}
err = register_candev(netdev);
if (err) {
- dev_err(netdev->dev.parent,
- "couldn't register CAN device: %d\n", err);
+ netdev_err(netdev, "couldn't register CAN device: %d\n", err);
goto cleanup_tx_msg_buffer;
}
return;
if (urb->status)
- dev_info(netdev->dev.parent, "Tx URB aborted (%d)\n",
- urb->status);
+ netdev_info(netdev, "Tx URB aborted (%d)\n", urb->status);
netdev->trans_start = jiffies;
}
if (err == -ENODEV)
netif_device_detach(netdev);
- dev_err(netdev->dev.parent, "couldn't start device: %d\n", err);
+ netdev_err(netdev, "couldn't start device: %d\n", err);
return err;
}
/* finally start device */
err = esd_usb2_start(priv);
if (err) {
- dev_warn(netdev->dev.parent,
- "couldn't start device: %d\n", err);
+ netdev_warn(netdev, "couldn't start device: %d\n", err);
close_candev(netdev);
return err;
}
/* create a URB, and a buffer for it, and copy the data to the URB */
urb = usb_alloc_urb(0, GFP_ATOMIC);
if (!urb) {
- dev_err(netdev->dev.parent, "No memory left for URBs\n");
+ netdev_err(netdev, "No memory left for URBs\n");
stats->tx_dropped++;
dev_kfree_skb(skb);
goto nourbmem;
buf = usb_alloc_coherent(dev->udev, size, GFP_ATOMIC,
&urb->transfer_dma);
if (!buf) {
- dev_err(netdev->dev.parent, "No memory left for USB buffer\n");
+ netdev_err(netdev, "No memory left for USB buffer\n");
stats->tx_dropped++;
dev_kfree_skb(skb);
goto nobufmem;
* This may never happen.
*/
if (!context) {
- dev_warn(netdev->dev.parent, "couldn't find free context\n");
+ netdev_warn(netdev, "couldn't find free context\n");
ret = NETDEV_TX_BUSY;
goto releasebuf;
}
if (err == -ENODEV)
netif_device_detach(netdev);
else
- dev_warn(netdev->dev.parent, "failed tx_urb %d\n", err);
+ netdev_warn(netdev, "failed tx_urb %d\n", err);
goto releasebuf;
}
for (i = 0; i <= ESD_MAX_ID_SEGMENT; i++)
msg.msg.filter.mask[i] = 0;
if (esd_usb2_send_msg(priv->usb2, &msg) < 0)
- dev_err(netdev->dev.parent, "sending idadd message failed\n");
+ netdev_err(netdev, "sending idadd message failed\n");
/* set CAN controller to reset mode */
msg.msg.hdr.len = 2;
msg.msg.setbaud.rsvd = 0;
msg.msg.setbaud.baud = cpu_to_le32(ESD_USB2_NO_BAUDRATE);
if (esd_usb2_send_msg(priv->usb2, &msg) < 0)
- dev_err(netdev->dev.parent, "sending setbaud message failed\n");
+ netdev_err(netdev, "sending setbaud message failed\n");
priv->can.state = CAN_STATE_STOPPED;
msg.msg.setbaud.rsvd = 0;
msg.msg.setbaud.baud = cpu_to_le32(canbtr);
- dev_info(netdev->dev.parent, "setting BTR=%#x\n", canbtr);
+ netdev_info(netdev, "setting BTR=%#x\n", canbtr);
return esd_usb2_send_msg(priv->usb2, &msg);
}
err = register_candev(netdev);
if (err) {
- dev_err(&intf->dev,
- "couldn't register CAN device: %d\n", err);
+ dev_err(&intf->dev, "couldn't register CAN device: %d\n", err);
free_candev(netdev);
err = -ENOMEM;
goto done;
}
dev->nets[index] = priv;
- dev_info(netdev->dev.parent, "device %s registered\n", netdev->name);
+ netdev_info(netdev, "device %s registered\n", netdev->name);
done:
return err;