* 'fbdev-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/fbdev-3.x:
vesafb: fix memory leak
fbdev: amba: Link fb device to its parent
fsl-diu-fb: remove check for pixel clock ranges
udlfb: Correct sub-optimal resolution selection.
hecubafb: add module_put on error path in hecubafb_probe()
sm501fb: fix section mismatch warning
gx1fb: Fix section mismatch warnings
fbdev: sh_mobile_meram: Correct pointer check for YCbCr chroma plane
E: zab@zabbo.net
D: maestro pci sound
-M: David Brownell
+N: David Brownell
D: Kernel engineer, mentor, and friend. Maintained USB EHCI and
D: gadget layers, SPI subsystem, GPIO subsystem, and more than a few
D: device drivers. His encouragement also helped many engineers get
Prefix: 'f71869'
Addresses scanned: none, address read from Super I/O config space
Datasheet: Available from the Fintek website
+ * Fintek F71869A
+ Prefix: 'f71869a'
+ Addresses scanned: none, address read from Super I/O config space
+ Datasheet: Not public
* Fintek F71882FG and F71883FG
Prefix: 'f71882fg'
Addresses scanned: none, address read from Super I/O config space
Socket S1G3: Athlon II, Sempron, Turion II
* AMD Family 11h processors:
Socket S1G2: Athlon (X2), Sempron (X2), Turion X2 (Ultra)
-* AMD Family 12h processors: "Llano"
-* AMD Family 14h processors: "Brazos" (C/E/G-Series)
+* AMD Family 12h processors: "Llano" (E2/A4/A6/A8-Series)
+* AMD Family 14h processors: "Brazos" (C/E/G/Z-Series)
* AMD Family 15h processors: "Bulldozer"
Prefix: 'k10temp'
http://support.amd.com/us/Processor_TechDocs/31116.pdf
BIOS and Kernel Developer's Guide (BKDG) for AMD Family 11h Processors:
http://support.amd.com/us/Processor_TechDocs/41256.pdf
+ BIOS and Kernel Developer's Guide (BKDG) for AMD Family 12h Processors:
+ http://support.amd.com/us/Processor_TechDocs/41131.pdf
BIOS and Kernel Developer's Guide (BKDG) for AMD Family 14h Models 00h-0Fh Processors:
http://support.amd.com/us/Processor_TechDocs/43170.pdf
Revision Guide for AMD Family 10h Processors:
http://support.amd.com/us/Processor_TechDocs/41322.pdf
Revision Guide for AMD Family 11h Processors:
http://support.amd.com/us/Processor_TechDocs/41788.pdf
+ Revision Guide for AMD Family 12h Processors:
+ http://support.amd.com/us/Processor_TechDocs/44739.pdf
Revision Guide for AMD Family 14h Models 00h-0Fh Processors:
http://support.amd.com/us/Processor_TechDocs/47534.pdf
AMD Family 11h Processor Power and Thermal Data Sheet for Notebooks:
should be used. Of course, for this purpose the device's run-time PM has to be
enabled earlier by calling pm_runtime_enable().
-If the device bus type's or driver's ->probe() or ->remove() callback runs
+If the device bus type's or driver's ->probe() callback runs
pm_runtime_suspend() or pm_runtime_idle() or their asynchronous counterparts,
they will fail returning -EAGAIN, because the device's usage counter is
-incremented by the core before executing ->probe() and ->remove(). Still, it
-may be desirable to suspend the device as soon as ->probe() or ->remove() has
-finished, so the PM core uses pm_runtime_idle_sync() to invoke the
-subsystem-level idle callback for the device at that time.
+incremented by the driver core before executing ->probe(). Still, it may be
+desirable to suspend the device as soon as ->probe() has finished, so the driver
+core uses pm_runtime_put_sync() to invoke the subsystem-level idle callback for
+the device at that time.
+
+Moreover, the driver core prevents runtime PM callbacks from racing with the bus
+notifier callback in __device_release_driver(), which is necessary, because the
+notifier is used by some subsystems to carry out operations affecting the
+runtime PM functionality. It does so by calling pm_runtime_get_sync() before
+driver_sysfs_remove() and the BUS_NOTIFY_UNBIND_DRIVER notifications. This
+resumes the device if it's in the suspended state and prevents it from
+being suspended again while those routines are being executed.
+
+To allow bus types and drivers to put devices into the suspended state by
+calling pm_runtime_suspend() from their ->remove() routines, the driver core
+executes pm_runtime_put_sync() after running the BUS_NOTIFY_UNBIND_DRIVER
+notifications in __device_release_driver(). This requires bus types and
+drivers to make their ->remove() callbacks avoid races with runtime PM directly,
+but also it allows of more flexibility in the handling of devices during the
+removal of their drivers.
The user space can effectively disallow the driver of the device to power manage
it at run time by changing the value of its /sys/devices/.../power/control
reported. That's because transfers often involve several packets, so that
one or more packets could finish before an error stops further endpoint I/O.
+For isochronous URBs, the urb status value is non-zero only if the URB is
+unlinked, the device is removed, the host controller is disabled, or the total
+transferred length is less than the requested length and the URB_SHORT_NOT_OK
+flag is set. Completion handlers for isochronous URBs should only see
+urb->status set to zero, -ENOENT, -ECONNRESET, -ESHUTDOWN, or -EREMOTEIO.
+Individual frame descriptor status fields may report more status codes.
+
0 Transfer completed successfully
device removal events immediately.
-EXDEV ISO transfer only partially completed
- look at individual frame status for details
+ (only set in iso_frame_desc[n].status, not urb->status)
-EINVAL ISO madness, if this happens: Log off and go home
F: include/linux/cfag12864b.h
AVR32 ARCHITECTURE
-M: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
+M: Haavard Skinnemoen <hskinnemoen@gmail.com>
+M: Hans-Christian Egtvedt <egtvedt@samfundet.no>
W: http://www.atmel.com/products/AVR32/
W: http://avr32linux.org/
W: http://avrfreaks.net/
-S: Supported
+S: Maintained
F: arch/avr32/
AVR32/AT32AP MACHINE SUPPORT
-M: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
-S: Supported
+M: Haavard Skinnemoen <hskinnemoen@gmail.com>
+M: Hans-Christian Egtvedt <egtvedt@samfundet.no>
+S: Maintained
F: arch/avr32/mach-at32ap/
AX.25 NETWORK LAYER
BATMAN ADVANCED
M: Marek Lindner <lindner_marek@yahoo.de>
M: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
-M: Sven Eckelmann <sven@narfation.org>
L: b.a.t.m.a.n@lists.open-mesh.org
W: http://www.open-mesh.org/
S: Maintained
F: arch/blackfin/
BLACKFIN EMAC DRIVER
-M: Michael Hennerich <michael.hennerich@analog.com>
L: uclinux-dist-devel@blackfin.uclinux.org
W: http://blackfin.uclinux.org
S: Supported
M: Oliver Hartkopp <socketcan@hartkopp.net>
M: Oliver Hartkopp <oliver.hartkopp@volkswagen.de>
M: Urs Thuermann <urs.thuermann@volkswagen.de>
-L: socketcan-core@lists.berlios.de
+L: socketcan-core@lists.berlios.de (subscribers-only)
L: netdev@vger.kernel.org
W: http://developer.berlios.de/projects/socketcan/
S: Maintained
CAN NETWORK DRIVERS
M: Wolfgang Grandegger <wg@grandegger.com>
-L: socketcan-core@lists.berlios.de
+L: socketcan-core@lists.berlios.de (subscribers-only)
L: netdev@vger.kernel.org
W: http://developer.berlios.de/projects/socketcan/
S: Maintained
F: drivers/net/qlcnic/
QLOGIC QLGE 10Gb ETHERNET DRIVER
+M: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
M: Ron Mercer <ron.mercer@qlogic.com>
M: linux-driver@qlogic.com
L: netdev@vger.kernel.org
F: drivers/usb/misc/rio500*
USB EHCI DRIVER
+M: Alan Stern <stern@rowland.harvard.edu>
L: linux-usb@vger.kernel.org
-S: Orphan
+S: Maintained
F: Documentation/usb/ehci.txt
F: drivers/usb/host/ehci*
F: Documentation/hid/hiddev.txt
F: drivers/hid/usbhid/
+USB/IP DRIVERS
+M: Matt Mooney <mfm@muteddisk.com>
+L: linux-usb@vger.kernel.org
+S: Maintained
+F: drivers/staging/usbip/
+
USB ISP116X DRIVER
M: Olav Kongas <ok@artecdesign.ee>
L: linux-usb@vger.kernel.org
F: sound/usb/midi.*
USB OHCI DRIVER
+M: Alan Stern <stern@rowland.harvard.edu>
L: linux-usb@vger.kernel.org
-S: Orphan
+S: Maintained
F: Documentation/usb/ohci.txt
F: drivers/usb/host/ohci*
VERSION = 3
PATCHLEVEL = 0
SUBLEVEL = 0
-EXTRAVERSION = -rc4
+EXTRAVERSION = -rc5
NAME = Sneaky Weasel
# *DOCUMENTATION*
- Linux kernel release 2.6.xx <http://kernel.org/>
+ Linux kernel release 3.x <http://kernel.org/>
-These are the release notes for Linux version 2.6. Read them carefully,
+These are the release notes for Linux version 3. Read them carefully,
as they tell you what this is all about, explain how to install the
kernel, and what to do if something goes wrong.
directory where you have permissions (eg. your home directory) and
unpack it:
- gzip -cd linux-2.6.XX.tar.gz | tar xvf -
+ gzip -cd linux-3.X.tar.gz | tar xvf -
or
- bzip2 -dc linux-2.6.XX.tar.bz2 | tar xvf -
+ bzip2 -dc linux-3.X.tar.bz2 | tar xvf -
Replace "XX" with the version number of the latest kernel.
files. They should match the library, and not get messed up by
whatever the kernel-du-jour happens to be.
- - You can also upgrade between 2.6.xx releases by patching. Patches are
+ - You can also upgrade between 3.x releases by patching. Patches are
distributed in the traditional gzip and the newer bzip2 format. To
install by patching, get all the newer patch files, enter the
- top level directory of the kernel source (linux-2.6.xx) and execute:
+ top level directory of the kernel source (linux-3.x) and execute:
- gzip -cd ../patch-2.6.xx.gz | patch -p1
+ gzip -cd ../patch-3.x.gz | patch -p1
or
- bzip2 -dc ../patch-2.6.xx.bz2 | patch -p1
+ bzip2 -dc ../patch-3.x.bz2 | patch -p1
(repeat xx for all versions bigger than the version of your current
source tree, _in_order_) and you should be ok. You may want to remove
failed patches (xxx# or xxx.rej). If there are, either you or me has
made a mistake.
- Unlike patches for the 2.6.x kernels, patches for the 2.6.x.y kernels
+ Unlike patches for the 3.x kernels, patches for the 3.x.y kernels
(also known as the -stable kernels) are not incremental but instead apply
- directly to the base 2.6.x kernel. Please read
+ directly to the base 3.x kernel. Please read
Documentation/applying-patches.txt for more information.
Alternatively, the script patch-kernel can be used to automate this
an alternative directory can be specified as the second argument.
- If you are upgrading between releases using the stable series patches
- (for example, patch-2.6.xx.y), note that these "dot-releases" are
- not incremental and must be applied to the 2.6.xx base tree. For
- example, if your base kernel is 2.6.12 and you want to apply the
- 2.6.12.3 patch, you do not and indeed must not first apply the
- 2.6.12.1 and 2.6.12.2 patches. Similarly, if you are running kernel
- version 2.6.12.2 and want to jump to 2.6.12.3, you must first
- reverse the 2.6.12.2 patch (that is, patch -R) _before_ applying
- the 2.6.12.3 patch.
+ (for example, patch-3.x.y), note that these "dot-releases" are
+ not incremental and must be applied to the 3.x base tree. For
+ example, if your base kernel is 3.0 and you want to apply the
+ 3.0.3 patch, you do not and indeed must not first apply the
+ 3.0.1 and 3.0.2 patches. Similarly, if you are running kernel
+ version 3.0.2 and want to jump to 3.0.3, you must first
+ reverse the 3.0.2 patch (that is, patch -R) _before_ applying
+ the 3.0.3 patch.
You can read more on this in Documentation/applying-patches.txt
- Make sure you have no stale .o files and dependencies lying around:
SOFTWARE REQUIREMENTS
- Compiling and running the 2.6.xx kernels requires up-to-date
+ Compiling and running the 3.x kernels requires up-to-date
versions of various software packages. Consult
Documentation/Changes for the minimum version numbers required
and how to get updates for these packages. Beware that using
Using the option "make O=output/dir" allow you to specify an alternate
place for the output files (including .config).
Example:
- kernel source code: /usr/src/linux-2.6.N
+ kernel source code: /usr/src/linux-3.N
build directory: /home/name/build/kernel
To configure and build the kernel use:
- cd /usr/src/linux-2.6.N
+ cd /usr/src/linux-3.N
make O=/home/name/build/kernel menuconfig
make O=/home/name/build/kernel
sudo make O=/home/name/build/kernel modules_install install
* Given a kernel address, find the home node of the underlying memory.
*/
#define kvaddr_to_nid(kaddr) pa_to_nid(__pa(kaddr))
-#define node_start_pfn(nid) (NODE_DATA(nid)->node_start_pfn)
/*
* Given a kaddr, LOCAL_BASE_ADDR finds the owning node of the memory
sub pc, lr, r0, lsr #32 @ properly flush pipeline
#endif
+#define PROC_ENTRY_SIZE (4*5)
+
/*
* Here follow the relocatable cache support functions for the
* various processors. This is a generic hook for locating an
ARM( addeq pc, r12, r3 ) @ call cache function
THUMB( addeq r12, r3 )
THUMB( moveq pc, r12 ) @ call cache function
- add r12, r12, #4*5
+ add r12, r12, #PROC_ENTRY_SIZE
b 1b
/*
.size proc_types, . - proc_types
+ /*
+ * If you get a "non-constant expression in ".if" statement"
+ * error from the assembler on this line, check that you have
+ * not accidentally written a "b" instruction where you should
+ * have written W(b).
+ */
+ .if (. - proc_types) % PROC_ENTRY_SIZE != 0
+ .error "The size of one or more proc_types entries is wrong."
+ .endif
+
/*
* Turn off the Cache and MMU. ARMv3 does not support
* reading the control register, but ARMv4 does.
* Do not include any C declarations in this file - it is included by
* assembler source.
*/
+#ifndef __ASM_ASSEMBLER_H__
+#define __ASM_ASSEMBLER_H__
+
#ifndef __ASSEMBLY__
#error "Only include this from assembly code"
#endif
.macro ldrusr, reg, ptr, inc, cond=al, rept=1, abort=9001f
usracc ldr, \reg, \ptr, \inc, \cond, \rept, \abort
.endm
+#endif /* __ASM_ASSEMBLER_H__ */
+#include <asm/assembler.h>
+
/*
* Interrupt handling. Preserves r7, r8, r9
*/
offset -= 0x02000000;
offset += sym->st_value - loc;
- /* only Thumb addresses allowed (no interworking) */
- if (!(offset & 1) ||
+ /*
+ * For function symbols, only Thumb addresses are
+ * allowed (no interworking).
+ *
+ * For non-function symbols, the destination
+ * has no specific ARM/Thumb disposition, so
+ * the branch is resolved under the assumption
+ * that interworking is not required.
+ */
+ if ((ELF32_ST_TYPE(sym->st_info) == STT_FUNC &&
+ !(offset & 1)) ||
offset <= (s32)0xff000000 ||
offset >= (s32)0x01000000) {
pr_err("%s: section %u reloc %u sym '%s': relocation %u out of range (%#lx -> %#x)\n",
smp_store_cpu_info(cpu);
/*
- * OK, now it's safe to let the boot CPU continue
+ * OK, now it's safe to let the boot CPU continue. Wait for
+ * the CPU migration code to notice that the CPU is online
+ * before we continue.
*/
set_cpu_online(cpu, true);
+ while (!cpu_active(cpu))
+ cpu_relax();
/*
* OK, it's off to the idle thread for us
tcfg->clocks = exynos4_serial_clocks;
tcfg->clocks_size = ARRAY_SIZE(exynos4_serial_clocks);
}
+ tcfg->flags |= NO_NEED_CHECK_CLKSRC;
}
s3c24xx_init_uartdevs("s5pv210-uart", s5p_uart_resources, cfg, no);
bool "gms30c7201"
depends on ARCH_H720X
select CPU_H7201
+ select ZONE_DMA
help
Say Y here if you are using the Hynix GMS30C7201 Reference Board
config ARCH_H7202
bool "hms30c7202"
select CPU_H7202
+ select ZONE_DMA
depends on ARCH_H720X
help
Say Y here if you are using the Hynix HMS30C7202 Reference Board
gpio_set_value(GPIO_PORT114, state);
}
-static struct sh_mobile_sdhi_info sh_sdhi1_platdata = {
+static struct sh_mobile_sdhi_info sh_sdhi1_info = {
.tmio_flags = TMIO_MMC_WRPROTECT_DISABLE,
.tmio_caps = MMC_CAP_NONREMOVABLE | MMC_CAP_SDIO_IRQ,
.tmio_ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34,
.name = "sh_mobile_sdhi",
.id = 1,
.dev = {
- .platform_data = &sh_sdhi1_platdata,
+ .platform_data = &sh_sdhi1_info,
},
.num_resources = ARRAY_SIZE(sdhi1_resources),
.resource = sdhi1_resources,
I2C_BOARD_INFO("imx074", 0x1a),
};
-struct soc_camera_link imx074_link = {
+static struct soc_camera_link imx074_link = {
.bus_id = 0,
.board_info = &imx074_info,
.i2c_adapter_id = 0,
&nor_flash_device,
&smc911x_device,
&lcdc_device,
- &usbhs0_device,
&usb1_host_device,
&usbhs1_device,
+ &usbhs0_device,
&leds_device,
&fsi_device,
&fsi_ak4643_device,
GPIO168_KP_O0,
/* UART */
- GPIO0_U0_CTSn | PIN_INPUT_PULLUP,
- GPIO1_U0_RTSn | PIN_OUTPUT_HIGH,
- GPIO2_U0_RXD | PIN_INPUT_PULLUP,
- GPIO3_U0_TXD | PIN_OUTPUT_HIGH,
+ /* uart-0 pins gpio configuration should be
+ * kept intact to prevent glitch in tx line
+ * when tty dev is opened. Later these pins
+ * are configured to uart mop500_pins_uart0
+ *
+ * It will be replaced with uart configuration
+ * once the issue is solved.
+ */
+ GPIO0_GPIO | PIN_INPUT_PULLUP,
+ GPIO1_GPIO | PIN_OUTPUT_HIGH,
+ GPIO2_GPIO | PIN_INPUT_PULLUP,
+ GPIO3_GPIO | PIN_OUTPUT_HIGH,
GPIO29_U2_RXD | PIN_INPUT_PULLUP,
GPIO30_U2_TXD | PIN_OUTPUT_HIGH,
#include <linux/leds-lp5521.h>
#include <linux/input.h>
#include <linux/gpio_keys.h>
+#include <linux/delay.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <plat/i2c.h>
#include <plat/ste_dma40.h>
+#include <plat/pincfg.h>
#include <mach/hardware.h>
#include <mach/setup.h>
#include <mach/devices.h>
#include <mach/irqs.h>
+#include "pins-db8500.h"
#include "ste-dma40-db8500.h"
#include "devices-db8500.h"
#include "board-mop500.h"
};
#endif
+
+static pin_cfg_t mop500_pins_uart0[] = {
+ GPIO0_U0_CTSn | PIN_INPUT_PULLUP,
+ GPIO1_U0_RTSn | PIN_OUTPUT_HIGH,
+ GPIO2_U0_RXD | PIN_INPUT_PULLUP,
+ GPIO3_U0_TXD | PIN_OUTPUT_HIGH,
+};
+
+#define PRCC_K_SOFTRST_SET 0x18
+#define PRCC_K_SOFTRST_CLEAR 0x1C
+static void ux500_uart0_reset(void)
+{
+ void __iomem *prcc_rst_set, *prcc_rst_clr;
+
+ prcc_rst_set = (void __iomem *)IO_ADDRESS(U8500_CLKRST1_BASE +
+ PRCC_K_SOFTRST_SET);
+ prcc_rst_clr = (void __iomem *)IO_ADDRESS(U8500_CLKRST1_BASE +
+ PRCC_K_SOFTRST_CLEAR);
+
+ /* Activate soft reset PRCC_K_SOFTRST_CLEAR */
+ writel((readl(prcc_rst_clr) | 0x1), prcc_rst_clr);
+ udelay(1);
+
+ /* Release soft reset PRCC_K_SOFTRST_SET */
+ writel((readl(prcc_rst_set) | 0x1), prcc_rst_set);
+ udelay(1);
+}
+
+static void ux500_uart0_init(void)
+{
+ int ret;
+
+ ret = nmk_config_pins(mop500_pins_uart0,
+ ARRAY_SIZE(mop500_pins_uart0));
+ if (ret < 0)
+ pr_err("pl011: uart pins_enable failed\n");
+}
+
+static void ux500_uart0_exit(void)
+{
+ int ret;
+
+ ret = nmk_config_pins_sleep(mop500_pins_uart0,
+ ARRAY_SIZE(mop500_pins_uart0));
+ if (ret < 0)
+ pr_err("pl011: uart pins_disable failed\n");
+}
+
static struct amba_pl011_data uart0_plat = {
#ifdef CONFIG_STE_DMA40
.dma_filter = stedma40_filter,
.dma_rx_param = &uart0_dma_cfg_rx,
.dma_tx_param = &uart0_dma_cfg_tx,
#endif
+ .init = ux500_uart0_init,
+ .exit = ux500_uart0_exit,
+ .reset = ux500_uart0_reset,
};
static struct amba_pl011_data uart1_plat = {
/* Suspend/resume support: derived from arch/arm/mach-s5pv210/sleep.S */
.globl cpu_v7_suspend_size
-.equ cpu_v7_suspend_size, 4 * 8
+.equ cpu_v7_suspend_size, 4 * 9
#ifdef CONFIG_PM_SLEEP
ENTRY(cpu_v7_do_suspend)
stmfd sp!, {r4 - r11, lr}
mrc p15, 0, r4, c13, c0, 0 @ FCSE/PID
mrc p15, 0, r5, c13, c0, 1 @ Context ID
+ mrc p15, 0, r6, c13, c0, 3 @ User r/o thread ID
+ stmia r0!, {r4 - r6}
mrc p15, 0, r6, c3, c0, 0 @ Domain ID
mrc p15, 0, r7, c2, c0, 0 @ TTB 0
mrc p15, 0, r8, c2, c0, 1 @ TTB 1
mrc p15, 0, r9, c1, c0, 0 @ Control register
mrc p15, 0, r10, c1, c0, 1 @ Auxiliary control register
mrc p15, 0, r11, c1, c0, 2 @ Co-processor access control
- stmia r0, {r4 - r11}
+ stmia r0, {r6 - r11}
ldmfd sp!, {r4 - r11, pc}
ENDPROC(cpu_v7_do_suspend)
mov ip, #0
mcr p15, 0, ip, c8, c7, 0 @ invalidate TLBs
mcr p15, 0, ip, c7, c5, 0 @ invalidate I cache
- ldmia r0, {r4 - r11}
+ ldmia r0!, {r4 - r6}
mcr p15, 0, r4, c13, c0, 0 @ FCSE/PID
mcr p15, 0, r5, c13, c0, 1 @ Context ID
+ mcr p15, 0, r6, c13, c0, 3 @ User r/o thread ID
+ ldmia r0, {r6 - r11}
mcr p15, 0, r6, c3, c0, 0 @ Domain ID
mcr p15, 0, r7, c2, c0, 0 @ TTB 0
mcr p15, 0, r8, c2, c0, 1 @ TTB 1
.word cpu_v7_dcache_clean_area
.word cpu_v7_switch_mm
.word cpu_v7_set_pte_ext
- .word 0
- .word 0
- .word 0
+ .word cpu_v7_suspend_size
+ .word cpu_v7_do_suspend
+ .word cpu_v7_do_resume
.size v7_processor_functions, . - v7_processor_functions
.section ".rodata"
*/
#include <linux/init.h>
#include <asm/traps.h>
+#include <asm/ptrace.h>
static int cp6_trap(struct pt_regs *regs, unsigned int instr)
{
#define S5PV210_UFSTAT_RXMASK (255<<0)
#define S5PV210_UFSTAT_RXSHIFT (0)
+#define NO_NEED_CHECK_CLKSRC 1
+
#ifndef __ASSEMBLY__
/* struct s3c24xx_uart_clksrc
#define NODE_DATA(nid) (node_data[nid])
#define node_localnr(pfn, nid) ((pfn) - NODE_DATA(nid)->node_start_pfn)
-#define node_start_pfn(nid) (NODE_DATA(nid)->node_start_pfn)
-#define node_end_pfn(nid) \
-({ \
- pg_data_t *__pgdat = NODE_DATA(nid); \
- __pgdat->node_start_pfn + __pgdat->node_spanned_pages - 1; \
-})
#define pmd_page(pmd) (pfn_to_page(pmd_val(pmd) >> PAGE_SHIFT))
/*
int node;
for (node = 0 ; node < MAX_NUMNODES ; node++)
- if (pfn >= node_start_pfn(node) && pfn <= node_end_pfn(node))
+ if (pfn >= node_start_pfn(node) && pfn < node_end_pfn(node))
break;
return node;
#define NODE_DATA(nid) (&node_data[nid].pg_data)
-#define node_start_pfn(nid) (NODE_DATA(nid)->node_start_pfn)
-#define node_end_pfn(nid) \
-({ \
- pg_data_t *__pgdat = NODE_DATA(nid); \
- __pgdat->node_start_pfn + __pgdat->node_spanned_pages; \
-})
-
/* We have these possible memory map layouts:
* Astro: 0-3.75, 67.75-68, 4-64
* zx1: 0-1, 257-260, 4-256
wm8776:codec@1a {
compatible = "wlf,wm8776";
reg = <0x1a>;
- /* MCLK source is a stand-alone oscillator */
- clock-frequency = <12288000>;
+ /*
+ * clock-frequency will be set by U-Boot if
+ * the clock is enabled.
+ */
};
};
codec-handle = <&wm8776>;
fsl,playback-dma = <&dma00>;
fsl,capture-dma = <&dma01>;
- fsl,fifo-depth = <16>;
+ fsl,fifo-depth = <15>;
+ fsl,ssi-asynchronous;
};
dma@c300 {
CONFIG_SCSI_CXGB3_ISCSI=m
CONFIG_SCSI_CXGB4_ISCSI=m
CONFIG_SCSI_BNX2_ISCSI=m
-CONFIG_SCSI_BNX2_ISCSI=m
CONFIG_BE2ISCSI=m
CONFIG_SCSI_IBMVSCSI=y
CONFIG_SCSI_IBMVFC=m
#define memory_hotplug_max() memblock_end_of_DRAM()
#endif
-/*
- * Following are macros that each numa implmentation must define.
- */
-
-#define node_start_pfn(nid) (NODE_DATA(nid)->node_start_pfn)
-#define node_end_pfn(nid) (NODE_DATA(nid)->node_end_pfn)
-
#else
#define memory_hotplug_max() memblock_end_of_DRAM()
#endif /* CONFIG_NEED_MULTIPLE_NODES */
#include <linux/init.h>
#include <linux/rtc.h>
#include <linux/delay.h>
+#include <linux/ratelimit.h>
#include <asm/prom.h>
#include <asm/rtas.h>
#include <asm/time.h>
}
} while (wait_time && (get_tb() < max_wait_tb));
- if (error != 0 && printk_ratelimit()) {
- printk(KERN_WARNING "error: reading the clock failed (%d)\n",
- error);
+ if (error != 0) {
+ printk_ratelimited(KERN_WARNING
+ "error: reading the clock failed (%d)\n",
+ error);
return 0;
}
wait_time = rtas_busy_delay_time(error);
if (wait_time) {
- if (in_interrupt() && printk_ratelimit()) {
+ if (in_interrupt()) {
memset(rtc_tm, 0, sizeof(struct rtc_time));
- printk(KERN_WARNING "error: reading clock"
- " would delay interrupt\n");
+ printk_ratelimited(KERN_WARNING
+ "error: reading clock "
+ "would delay interrupt\n");
return; /* delay not allowed */
}
msleep(wait_time);
}
} while (wait_time && (get_tb() < max_wait_tb));
- if (error != 0 && printk_ratelimit()) {
- printk(KERN_WARNING "error: reading the clock failed (%d)\n",
- error);
+ if (error != 0) {
+ printk_ratelimited(KERN_WARNING
+ "error: reading the clock failed (%d)\n",
+ error);
return;
}
}
} while (wait_time && (get_tb() < max_wait_tb));
- if (error != 0 && printk_ratelimit())
- printk(KERN_WARNING "error: setting the clock failed (%d)\n",
- error);
+ if (error != 0)
+ printk_ratelimited(KERN_WARNING
+ "error: setting the clock failed (%d)\n",
+ error);
return 0;
}
#include <linux/errno.h>
#include <linux/elf.h>
#include <linux/ptrace.h>
+#include <linux/ratelimit.h>
#ifdef CONFIG_PPC64
#include <linux/syscalls.h>
#include <linux/compat.h>
printk("badframe in handle_rt_signal, regs=%p frame=%p newsp=%lx\n",
regs, frame, newsp);
#endif
- if (show_unhandled_signals && printk_ratelimit())
- printk(KERN_INFO "%s[%d]: bad frame in handle_rt_signal32: "
- "%p nip %08lx lr %08lx\n",
- current->comm, current->pid,
- addr, regs->nip, regs->link);
+ if (show_unhandled_signals)
+ printk_ratelimited(KERN_INFO
+ "%s[%d]: bad frame in handle_rt_signal32: "
+ "%p nip %08lx lr %08lx\n",
+ current->comm, current->pid,
+ addr, regs->nip, regs->link);
force_sigsegv(sig, current);
return 0;
return 0;
bad:
- if (show_unhandled_signals && printk_ratelimit())
- printk(KERN_INFO "%s[%d]: bad frame in sys_rt_sigreturn: "
- "%p nip %08lx lr %08lx\n",
- current->comm, current->pid,
- rt_sf, regs->nip, regs->link);
+ if (show_unhandled_signals)
+ printk_ratelimited(KERN_INFO
+ "%s[%d]: bad frame in sys_rt_sigreturn: "
+ "%p nip %08lx lr %08lx\n",
+ current->comm, current->pid,
+ rt_sf, regs->nip, regs->link);
force_sig(SIGSEGV, current);
return 0;
* We kill the task with a SIGSEGV in this situation.
*/
if (do_setcontext(ctx, regs, 1)) {
- if (show_unhandled_signals && printk_ratelimit())
- printk(KERN_INFO "%s[%d]: bad frame in "
- "sys_debug_setcontext: %p nip %08lx "
- "lr %08lx\n",
- current->comm, current->pid,
- ctx, regs->nip, regs->link);
+ if (show_unhandled_signals)
+ printk_ratelimited(KERN_INFO "%s[%d]: bad frame in "
+ "sys_debug_setcontext: %p nip %08lx "
+ "lr %08lx\n",
+ current->comm, current->pid,
+ ctx, regs->nip, regs->link);
force_sig(SIGSEGV, current);
goto out;
printk("badframe in handle_signal, regs=%p frame=%p newsp=%lx\n",
regs, frame, newsp);
#endif
- if (show_unhandled_signals && printk_ratelimit())
- printk(KERN_INFO "%s[%d]: bad frame in handle_signal32: "
- "%p nip %08lx lr %08lx\n",
- current->comm, current->pid,
- frame, regs->nip, regs->link);
+ if (show_unhandled_signals)
+ printk_ratelimited(KERN_INFO
+ "%s[%d]: bad frame in handle_signal32: "
+ "%p nip %08lx lr %08lx\n",
+ current->comm, current->pid,
+ frame, regs->nip, regs->link);
force_sigsegv(sig, current);
return 0;
return 0;
badframe:
- if (show_unhandled_signals && printk_ratelimit())
- printk(KERN_INFO "%s[%d]: bad frame in sys_sigreturn: "
- "%p nip %08lx lr %08lx\n",
- current->comm, current->pid,
- addr, regs->nip, regs->link);
+ if (show_unhandled_signals)
+ printk_ratelimited(KERN_INFO
+ "%s[%d]: bad frame in sys_sigreturn: "
+ "%p nip %08lx lr %08lx\n",
+ current->comm, current->pid,
+ addr, regs->nip, regs->link);
force_sig(SIGSEGV, current);
return 0;
#include <linux/elf.h>
#include <linux/ptrace.h>
#include <linux/module.h>
+#include <linux/ratelimit.h>
#include <asm/sigcontext.h>
#include <asm/ucontext.h>
printk("badframe in sys_rt_sigreturn, regs=%p uc=%p &uc->uc_mcontext=%p\n",
regs, uc, &uc->uc_mcontext);
#endif
- if (show_unhandled_signals && printk_ratelimit())
- printk(regs->msr & MSR_64BIT ? fmt64 : fmt32,
- current->comm, current->pid, "rt_sigreturn",
- (long)uc, regs->nip, regs->link);
+ if (show_unhandled_signals)
+ printk_ratelimited(regs->msr & MSR_64BIT ? fmt64 : fmt32,
+ current->comm, current->pid, "rt_sigreturn",
+ (long)uc, regs->nip, regs->link);
force_sig(SIGSEGV, current);
return 0;
printk("badframe in setup_rt_frame, regs=%p frame=%p newsp=%lx\n",
regs, frame, newsp);
#endif
- if (show_unhandled_signals && printk_ratelimit())
- printk(regs->msr & MSR_64BIT ? fmt64 : fmt32,
- current->comm, current->pid, "setup_rt_frame",
- (long)frame, regs->nip, regs->link);
+ if (show_unhandled_signals)
+ printk_ratelimited(regs->msr & MSR_64BIT ? fmt64 : fmt32,
+ current->comm, current->pid, "setup_rt_frame",
+ (long)frame, regs->nip, regs->link);
force_sigsegv(signr, current);
return 0;
#include <linux/bug.h>
#include <linux/kdebug.h>
#include <linux/debugfs.h>
+#include <linux/ratelimit.h>
#include <asm/emulated_ops.h>
#include <asm/pgtable.h>
if (die("Exception in kernel mode", regs, signr))
return;
} else if (show_unhandled_signals &&
- unhandled_signal(current, signr) &&
- printk_ratelimit()) {
- printk(regs->msr & MSR_64BIT ? fmt64 : fmt32,
- current->comm, current->pid, signr,
- addr, regs->nip, regs->link, code);
- }
+ unhandled_signal(current, signr)) {
+ printk_ratelimited(regs->msr & MSR_64BIT ? fmt64 : fmt32,
+ current->comm, current->pid, signr,
+ addr, regs->nip, regs->link, code);
+ }
memset(&info, 0, sizeof(info));
info.si_signo = signr;
unsigned long reason = mcsr;
int recoverable = 1;
- if (reason & MCSR_BUS_RBERR) {
+ if (reason & MCSR_LD) {
recoverable = fsl_rio_mcheck_exception(regs);
if (recoverable == 1)
goto silent_out;
} else {
/* didn't recognize the instruction */
/* XXX quick hack for now: set the non-Java bit in the VSCR */
- if (printk_ratelimit())
- printk(KERN_ERR "Unrecognized altivec instruction "
- "in %s at %lx\n", current->comm, regs->nip);
+ printk_ratelimited(KERN_ERR "Unrecognized altivec instruction "
+ "in %s at %lx\n", current->comm, regs->nip);
current->thread.vscr.u[3] |= 0x10000;
}
}
void ppc_warn_emulated_print(const char *type)
{
- if (printk_ratelimit())
- pr_warning("%s used emulated %s instruction\n", current->comm,
- type);
+ pr_warn_ratelimited("%s used emulated %s instruction\n", current->comm,
+ type);
}
static int __init ppc_warn_emulated_init(void)
#include <linux/kdebug.h>
#include <linux/perf_event.h>
#include <linux/magic.h>
+#include <linux/ratelimit.h>
#include <asm/firmware.h>
#include <asm/page.h>
return 0;
}
- if (is_exec && (error_code & DSISR_PROTFAULT)
- && printk_ratelimit())
- printk(KERN_CRIT "kernel tried to execute NX-protected"
- " page (%lx) - exploit attempt? (uid: %d)\n",
- address, current_uid());
+ if (is_exec && (error_code & DSISR_PROTFAULT))
+ printk_ratelimited(KERN_CRIT "kernel tried to execute NX-protected"
+ " page (%lx) - exploit attempt? (uid: %d)\n",
+ address, current_uid());
return SIGSEGV;
#ifdef CONFIG_E500
int fsl_rio_mcheck_exception(struct pt_regs *regs)
{
- const struct exception_table_entry *entry = NULL;
- unsigned long reason = mfspr(SPRN_MCSR);
-
- if (reason & MCSR_BUS_RBERR) {
- reason = in_be32((u32 *)(rio_regs_win + RIO_LTLEDCSR));
- if (reason & (RIO_LTLEDCSR_IER | RIO_LTLEDCSR_PRT)) {
- /* Check if we are prepared to handle this fault */
- entry = search_exception_tables(regs->nip);
- if (entry) {
- pr_debug("RIO: %s - MC Exception handled\n",
- __func__);
- out_be32((u32 *)(rio_regs_win + RIO_LTLEDCSR),
- 0);
- regs->msr |= MSR_RI;
- regs->nip = entry->fixup;
- return 1;
- }
+ const struct exception_table_entry *entry;
+ unsigned long reason;
+
+ if (!rio_regs_win)
+ return 0;
+
+ reason = in_be32((u32 *)(rio_regs_win + RIO_LTLEDCSR));
+ if (reason & (RIO_LTLEDCSR_IER | RIO_LTLEDCSR_PRT)) {
+ /* Check if we are prepared to handle this fault */
+ entry = search_exception_tables(regs->nip);
+ if (entry) {
+ pr_debug("RIO: %s - MC Exception handled\n",
+ __func__);
+ out_be32((u32 *)(rio_regs_win + RIO_LTLEDCSR),
+ 0);
+ regs->msr |= MSR_RI;
+ regs->nip = entry->fixup;
+ return 1;
}
}
#include <linux/pci.h>
#include <linux/slab.h>
#include <linux/syscore_ops.h>
+#include <linux/ratelimit.h>
#include <asm/ptrace.h>
#include <asm/signal.h>
return NO_IRQ;
}
if (unlikely(mpic->protected && test_bit(src, mpic->protected))) {
- if (printk_ratelimit())
- printk(KERN_WARNING "%s: Got protected source %d !\n",
- mpic->name, (int)src);
+ printk_ratelimited(KERN_WARNING "%s: Got protected source %d !\n",
+ mpic->name, (int)src);
mpic_eoi(mpic);
return NO_IRQ;
}
return NO_IRQ;
}
if (unlikely(mpic->protected && test_bit(src, mpic->protected))) {
- if (printk_ratelimit())
- printk(KERN_WARNING "%s: Got protected source %d !\n",
- mpic->name, (int)src);
+ printk_ratelimited(KERN_WARNING "%s: Got protected source %d !\n",
+ mpic->name, (int)src);
return NO_IRQ;
}
def_bool y
prompt "s390 guest support for KVM (EXPERIMENTAL)"
depends on 64BIT && EXPERIMENTAL
+ select VIRTUALIZATION
select VIRTIO
select VIRTIO_RING
select VIRTIO_CONSOLE
memset(&parms.orvals, 0, sizeof(parms.orvals));
memset(&parms.andvals, 0xff, sizeof(parms.andvals));
- parms.orvals[cr] = 1 << bit;
+ parms.orvals[cr] = 1UL << bit;
on_each_cpu(smp_ctl_bit_callback, &parms, 1);
}
EXPORT_SYMBOL(smp_ctl_set_bit);
memset(&parms.orvals, 0, sizeof(parms.orvals));
memset(&parms.andvals, 0xff, sizeof(parms.andvals));
- parms.andvals[cr] = ~(1L << bit);
+ parms.andvals[cr] = ~(1UL << bit);
on_each_cpu(smp_ctl_bit_callback, &parms, 1);
}
EXPORT_SYMBOL(smp_ctl_clear_bit);
#include "hwsampler.h"
-#define DEFAULT_INTERVAL 4096
+#define DEFAULT_INTERVAL 4127518
#define DEFAULT_SDBT_BLOCKS 1
#define DEFAULT_SDB_BLOCKS 511
if (oprofile_max_interval == 0)
return -ENODEV;
+ /* The initial value should be sane */
+ if (oprofile_hw_interval < oprofile_min_interval)
+ oprofile_hw_interval = oprofile_min_interval;
+ if (oprofile_hw_interval > oprofile_max_interval)
+ oprofile_hw_interval = oprofile_max_interval;
+
if (oprofile_timer_init(ops))
return -ENODEV;
select SYS_SUPPORTS_CMT
select ARCH_WANT_OPTIONAL_GPIOLIB
select USB_ARCH_HAS_OHCI
+ select USB_OHCI_SH if USB_OHCI_HCD
help
Select SH7720 if you have a SH3-DSP SH7720 CPU.
select CPU_HAS_DSP
select SYS_SUPPORTS_CMT
select USB_ARCH_HAS_OHCI
+ select USB_OHCI_SH if USB_OHCI_HCD
help
Select SH7721 if you have a SH3-DSP SH7721 CPU.
bool "Support SH7763 processor"
select CPU_SH4A
select USB_ARCH_HAS_OHCI
+ select USB_OHCI_SH if USB_OHCI_HCD
help
Select SH7763 if you have a SH4A SH7763(R5S77631) CPU.
select GENERIC_CLOCKEVENTS_BROADCAST if SMP
select ARCH_WANT_OPTIONAL_GPIOLIB
select USB_ARCH_HAS_OHCI
+ select USB_OHCI_SH if USB_OHCI_HCD
select USB_ARCH_HAS_EHCI
+ select USB_EHCI_SH if USB_EHCI_HCD
config CPU_SUBTYPE_SHX3
bool "Support SH-X3 processor"
CONFIG_TASK_IO_ACCOUNTING=y
CONFIG_LOG_BUF_SHIFT=14
CONFIG_BLK_DEV_INITRD=y
-# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
# CONFIG_SYSCTL_SYSCALL is not set
CONFIG_KALLSYMS_ALL=y
CONFIG_SLAB=y
CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
# CONFIG_FW_LOADER is not set
CONFIG_MTD=y
-CONFIG_MTD_CONCAT=y
-CONFIG_MTD_PARTITIONS=y
CONFIG_MTD_CHAR=y
CONFIG_MTD_BLOCK=y
CONFIG_MTD_M25P80=y
# CONFIG_KEYBOARD_ATKBD is not set
# CONFIG_MOUSE_PS2 is not set
# CONFIG_SERIO is not set
+# CONFIG_LEGACY_PTYS is not set
CONFIG_SERIAL_SH_SCI=y
CONFIG_SERIAL_SH_SCI_NR_UARTS=3
CONFIG_SERIAL_SH_SCI_CONSOLE=y
-# CONFIG_LEGACY_PTYS is not set
# CONFIG_HW_RANDOM is not set
CONFIG_SPI=y
CONFIG_SPI_SH=y
# CONFIG_HWMON is not set
-CONFIG_MFD_SH_MOBILE_SDHI=y
CONFIG_USB=y
CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_EHCI_SH=y
CONFIG_USB_OHCI_HCD=y
+CONFIG_USB_OHCI_SH=y
CONFIG_USB_STORAGE=y
CONFIG_MMC=y
CONFIG_MMC_SDHI=y
extern struct pglist_data *node_data[];
#define NODE_DATA(nid) (node_data[nid])
-#define node_start_pfn(nid) (NODE_DATA(nid)->node_start_pfn)
-#define node_end_pfn(nid) (NODE_DATA(nid)->node_start_pfn + \
- NODE_DATA(nid)->node_spanned_pages)
-
static inline int pfn_to_nid(unsigned long pfn)
{
int nid;
{
.slave_id = SHDMA_SLAVE_SCIF2_RX,
.addr = 0x1f4b0014,
- .chcr = SM_INC | 0x800 | 0x40000000 |
+ .chcr = DM_INC | 0x800 | 0x40000000 |
TS_INDEX2VAL(XMIT_SZ_8BIT),
.mid_rid = 0x22,
},
{
.slave_id = SHDMA_SLAVE_SCIF3_RX,
.addr = 0x1f4c0014,
- .chcr = SM_INC | 0x800 | 0x40000000 |
+ .chcr = DM_INC | 0x800 | 0x40000000 |
TS_INDEX2VAL(XMIT_SZ_8BIT),
.mid_rid = 0x2a,
},
{
.slave_id = SHDMA_SLAVE_SCIF4_RX,
.addr = 0x1f4d0014,
- .chcr = SM_INC | 0x800 | 0x40000000 |
+ .chcr = DM_INC | 0x800 | 0x40000000 |
TS_INDEX2VAL(XMIT_SZ_8BIT),
.mid_rid = 0x42,
},
{
.slave_id = SHDMA_SLAVE_RIIC0_RX,
.addr = 0x1e500013,
- .chcr = SM_INC | 0x800 | 0x40000000 |
+ .chcr = DM_INC | 0x800 | 0x40000000 |
TS_INDEX2VAL(XMIT_SZ_8BIT),
.mid_rid = 0x22,
},
{
.slave_id = SHDMA_SLAVE_RIIC1_RX,
.addr = 0x1e510013,
- .chcr = SM_INC | 0x800 | 0x40000000 |
+ .chcr = DM_INC | 0x800 | 0x40000000 |
TS_INDEX2VAL(XMIT_SZ_8BIT),
.mid_rid = 0x2a,
},
{
.slave_id = SHDMA_SLAVE_RIIC2_RX,
.addr = 0x1e520013,
- .chcr = SM_INC | 0x800 | 0x40000000 |
+ .chcr = DM_INC | 0x800 | 0x40000000 |
TS_INDEX2VAL(XMIT_SZ_8BIT),
.mid_rid = 0xa2,
},
.addr = 0x1e530012,
.chcr = SM_INC | 0x800 | 0x40000000 |
TS_INDEX2VAL(XMIT_SZ_8BIT),
- .mid_rid = 0xab,
+ .mid_rid = 0xa9,
},
{
.slave_id = SHDMA_SLAVE_RIIC3_RX,
.addr = 0x1e530013,
- .chcr = SM_INC | 0x800 | 0x40000000 |
+ .chcr = DM_INC | 0x800 | 0x40000000 |
TS_INDEX2VAL(XMIT_SZ_8BIT),
.mid_rid = 0xaf,
},
.addr = 0x1e540012,
.chcr = SM_INC | 0x800 | 0x40000000 |
TS_INDEX2VAL(XMIT_SZ_8BIT),
- .mid_rid = 0xc1,
+ .mid_rid = 0xc5,
},
{
.slave_id = SHDMA_SLAVE_RIIC4_RX,
.addr = 0x1e540013,
- .chcr = SM_INC | 0x800 | 0x40000000 |
+ .chcr = DM_INC | 0x800 | 0x40000000 |
TS_INDEX2VAL(XMIT_SZ_8BIT),
- .mid_rid = 0xc2,
+ .mid_rid = 0xc6,
},
};
{
.slave_id = SHDMA_SLAVE_RIIC5_RX,
.addr = 0x1e550013,
- .chcr = SM_INC | 0x800 | 0x40000000 |
+ .chcr = DM_INC | 0x800 | 0x40000000 |
TS_INDEX2VAL(XMIT_SZ_8BIT),
.mid_rid = 0x22,
},
{
.slave_id = SHDMA_SLAVE_RIIC6_RX,
.addr = 0x1e560013,
- .chcr = SM_INC | 0x800 | 0x40000000 |
+ .chcr = DM_INC | 0x800 | 0x40000000 |
TS_INDEX2VAL(XMIT_SZ_8BIT),
.mid_rid = 0x2a,
},
{
.slave_id = SHDMA_SLAVE_RIIC7_RX,
.addr = 0x1e570013,
- .chcr = SM_INC | 0x800 | 0x40000000 |
+ .chcr = DM_INC | 0x800 | 0x40000000 |
TS_INDEX2VAL(XMIT_SZ_8BIT),
.mid_rid = 0x42,
},
{
.slave_id = SHDMA_SLAVE_RIIC8_RX,
.addr = 0x1e580013,
- .chcr = SM_INC | 0x800 | 0x40000000 |
+ .chcr = DM_INC | 0x800 | 0x40000000 |
TS_INDEX2VAL(XMIT_SZ_8BIT),
.mid_rid = 0x46,
},
{
.slave_id = SHDMA_SLAVE_RIIC9_RX,
.addr = 0x1e590013,
- .chcr = SM_INC | 0x800 | 0x40000000 |
+ .chcr = DM_INC | 0x800 | 0x40000000 |
TS_INDEX2VAL(XMIT_SZ_8BIT),
.mid_rid = 0x52,
},
.resource = spi0_resources,
};
+static struct resource usb_ehci_resources[] = {
+ [0] = {
+ .start = 0xfe4f1000,
+ .end = 0xfe4f10ff,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = 57,
+ .end = 57,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device usb_ehci_device = {
+ .name = "sh_ehci",
+ .id = -1,
+ .dev = {
+ .dma_mask = &usb_ehci_device.dev.coherent_dma_mask,
+ .coherent_dma_mask = DMA_BIT_MASK(32),
+ },
+ .num_resources = ARRAY_SIZE(usb_ehci_resources),
+ .resource = usb_ehci_resources,
+};
+
+static struct resource usb_ohci_resources[] = {
+ [0] = {
+ .start = 0xfe4f1800,
+ .end = 0xfe4f18ff,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = 57,
+ .end = 57,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device usb_ohci_device = {
+ .name = "sh_ohci",
+ .id = -1,
+ .dev = {
+ .dma_mask = &usb_ohci_device.dev.coherent_dma_mask,
+ .coherent_dma_mask = DMA_BIT_MASK(32),
+ },
+ .num_resources = ARRAY_SIZE(usb_ohci_resources),
+ .resource = usb_ohci_resources,
+};
+
static struct platform_device *sh7757_devices[] __initdata = {
&scif2_device,
&scif3_device,
&dma2_device,
&dma3_device,
&spi0_device,
+ &usb_ehci_device,
+ &usb_ohci_device,
};
static int __init sh7757_devices_setup(void)
/* Support for external interrupt pins in IRQ mode */
static struct intc_vect vectors_irq0123[] __initdata = {
- INTC_VECT(IRQ0, 0x240), INTC_VECT(IRQ1, 0x280),
- INTC_VECT(IRQ2, 0x2c0), INTC_VECT(IRQ3, 0x300),
+ INTC_VECT(IRQ0, 0x200), INTC_VECT(IRQ1, 0x240),
+ INTC_VECT(IRQ2, 0x280), INTC_VECT(IRQ3, 0x2c0),
};
static struct intc_vect vectors_irq4567[] __initdata = {
- INTC_VECT(IRQ4, 0x340), INTC_VECT(IRQ5, 0x380),
- INTC_VECT(IRQ6, 0x3c0), INTC_VECT(IRQ7, 0x200),
+ INTC_VECT(IRQ4, 0x300), INTC_VECT(IRQ5, 0x340),
+ INTC_VECT(IRQ6, 0x380), INTC_VECT(IRQ7, 0x3c0),
};
static struct intc_sense_reg sense_registers[] __initdata = {
};
static struct intc_vect vectors_irl4567[] __initdata = {
- INTC_VECT(IRL4_LLLL, 0xb00), INTC_VECT(IRL4_LLLH, 0xb20),
- INTC_VECT(IRL4_LLHL, 0xb40), INTC_VECT(IRL4_LLHH, 0xb60),
- INTC_VECT(IRL4_LHLL, 0xb80), INTC_VECT(IRL4_LHLH, 0xba0),
- INTC_VECT(IRL4_LHHL, 0xbc0), INTC_VECT(IRL4_LHHH, 0xbe0),
- INTC_VECT(IRL4_HLLL, 0xc00), INTC_VECT(IRL4_HLLH, 0xc20),
- INTC_VECT(IRL4_HLHL, 0xc40), INTC_VECT(IRL4_HLHH, 0xc60),
- INTC_VECT(IRL4_HHLL, 0xc80), INTC_VECT(IRL4_HHLH, 0xca0),
- INTC_VECT(IRL4_HHHL, 0xcc0),
+ INTC_VECT(IRL4_LLLL, 0x200), INTC_VECT(IRL4_LLLH, 0x220),
+ INTC_VECT(IRL4_LLHL, 0x240), INTC_VECT(IRL4_LLHH, 0x260),
+ INTC_VECT(IRL4_LHLL, 0x280), INTC_VECT(IRL4_LHLH, 0x2a0),
+ INTC_VECT(IRL4_LHHL, 0x2c0), INTC_VECT(IRL4_LHHH, 0x2e0),
+ INTC_VECT(IRL4_HLLL, 0x300), INTC_VECT(IRL4_HLLH, 0x320),
+ INTC_VECT(IRL4_HLHL, 0x340), INTC_VECT(IRL4_HLHH, 0x360),
+ INTC_VECT(IRL4_HHLL, 0x380), INTC_VECT(IRL4_HHLH, 0x3a0),
+ INTC_VECT(IRL4_HHHL, 0x3c0),
};
static DECLARE_INTC_DESC(intc_desc_irl0123, "sh7757-irl0123", vectors_irl0123,
#include <linux/seq_file.h>
#include <linux/ftrace.h>
#include <linux/delay.h>
+#include <linux/ratelimit.h>
#include <asm/processor.h>
#include <asm/machvec.h>
#include <asm/uaccess.h>
unsigned int newcpu = cpumask_any_and(data->affinity,
cpu_online_mask);
if (newcpu >= nr_cpu_ids) {
- if (printk_ratelimit())
- printk(KERN_INFO "IRQ%u no longer affine to CPU%u\n",
- irq, cpu);
+ pr_info_ratelimited("IRQ%u no longer affine to CPU%u\n",
+ irq, cpu);
cpumask_setall(data->affinity);
newcpu = cpumask_any_and(data->affinity,
#include <linux/seq_file.h>
#include <linux/proc_fs.h>
#include <linux/uaccess.h>
+#include <linux/ratelimit.h>
#include <asm/alignment.h>
#include <asm/processor.h>
void unaligned_fixups_notify(struct task_struct *tsk, insn_size_t insn,
struct pt_regs *regs)
{
- if (user_mode(regs) && (se_usermode & UM_WARN) && printk_ratelimit())
- pr_notice("Fixing up unaligned userspace access "
+ if (user_mode(regs) && (se_usermode & UM_WARN))
+ pr_notice_ratelimited("Fixing up unaligned userspace access "
"in \"%s\" pid=%d pc=0x%p ins=0x%04hx\n",
tsk->comm, task_pid_nr(tsk),
(void *)instruction_pointer(regs), insn);
- else if (se_kernmode_warn && printk_ratelimit())
- pr_notice("Fixing up unaligned kernel access "
+ else if (se_kernmode_warn)
+ pr_notice_ratelimited("Fixing up unaligned kernel access "
"in \"%s\" pid=%d pc=0x%p ins=0x%04hx\n",
tsk->comm, task_pid_nr(tsk),
(void *)instruction_pointer(regs), insn);
extern struct pglist_data *node_data[];
#define NODE_DATA(nid) (node_data[nid])
-#define node_start_pfn(nid) (NODE_DATA(nid)->node_start_pfn)
-#define node_end_pfn(nid) (NODE_DATA(nid)->node_end_pfn)
extern int numa_cpu_lookup_table[];
extern cpumask_t numa_cpumask_lookup_table[];
return highbits_to_node[__pfn_to_highbits(pfn)];
}
-/*
- * Following are macros that each numa implmentation must define.
- */
-
-#define node_start_pfn(nid) (NODE_DATA(nid)->node_start_pfn)
-#define node_end_pfn(nid) \
-({ \
- pg_data_t *__pgdat = NODE_DATA(nid); \
- __pgdat->node_start_pfn + __pgdat->node_spanned_pages; \
-})
-
#define kern_addr_valid(kaddr) virt_addr_valid((void *)kaddr)
static inline int pfn_valid(int pfn)
--- /dev/null
+#ifndef __UM_PERCPU_H
+#define __UM_PERCPU_H
+
+#include <asm-generic/percpu.h>
+
+#endif /* __UM_PERCPU_H */
#else /* CONFIG_APB_TIMER */
static inline unsigned long apbt_quick_calibrate(void) {return 0; }
-static inline void apbt_time_init(void) {return 0; }
+static inline void apbt_time_init(void) { }
#endif
#endif /* ASM_X86_APBT_H */
#endif
}
-/*
- * Following are macros that each numa implmentation must define.
- */
-
-#define node_start_pfn(nid) (NODE_DATA(nid)->node_start_pfn)
-#define node_end_pfn(nid) \
-({ \
- pg_data_t *__pgdat = NODE_DATA(nid); \
- __pgdat->node_start_pfn + __pgdat->node_spanned_pages; \
-})
-
static inline int pfn_valid(int pfn)
{
int nid = pfn_to_nid(pfn);
#define NODE_DATA(nid) (node_data[nid])
-#define node_start_pfn(nid) (NODE_DATA(nid)->node_start_pfn)
-#define node_end_pfn(nid) (NODE_DATA(nid)->node_start_pfn + \
- NODE_DATA(nid)->node_spanned_pages)
#endif
#endif /* _ASM_X86_MMZONE_64_H */
int def_op_bytes, def_ad_bytes, goffset, simd_prefix;
bool op_prefix = false;
struct opcode opcode;
- struct operand memop = { .type = OP_NONE };
+ struct operand memop = { .type = OP_NONE }, *memopp = NULL;
c->eip = ctxt->eip;
c->fetch.start = c->eip;
if (memop.type == OP_MEM && c->ad_bytes != 8)
memop.addr.mem.ea = (u32)memop.addr.mem.ea;
- if (memop.type == OP_MEM && c->rip_relative)
- memop.addr.mem.ea += c->eip;
-
/*
* Decode and fetch the source operand: register, memory
* or immediate.
c->op_bytes;
srcmem_common:
c->src = memop;
+ memopp = &c->src;
break;
case SrcImmU16:
rc = decode_imm(ctxt, &c->src, 2, false);
case DstMem:
case DstMem64:
c->dst = memop;
+ memopp = &c->dst;
if ((c->d & DstMask) == DstMem64)
c->dst.bytes = 8;
else
/* Special instructions do their own operand decoding. */
default:
c->dst.type = OP_NONE; /* Disable writeback. */
- return 0;
+ break;
}
done:
+ if (memopp && memopp->type == OP_MEM && c->rip_relative)
+ memopp->addr.mem.ea += c->eip;
+
return (rc == X86EMUL_UNHANDLEABLE) ? EMULATION_FAILED : EMULATION_OK;
}
return false;
}
-static void coalesce_windows(struct pci_root_info *info, int type)
+static void coalesce_windows(struct pci_root_info *info, unsigned long type)
{
int i, j;
struct resource *res1, *res2;
struct physdev_map_pirq map_irq;
int shareable = 0;
char *name;
+ bool gsi_override = false;
if (!xen_pv_domain())
return -1;
if (pirq < 0)
goto out;
- irq = xen_bind_pirq_gsi_to_irq(gsi, pirq, shareable, name);
+ /* Before we bind the GSI to a Linux IRQ, check whether
+ * we need to override it with bus_irq (IRQ) value. Usually for
+ * IRQs below IRQ_LEGACY_IRQ this holds IRQ == GSI, as so:
+ * ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
+ * but there are oddballs where the IRQ != GSI:
+ * ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 20 low level)
+ * which ends up being: gsi_to_irq[9] == 20
+ * (which is what acpi_gsi_to_irq ends up calling when starting the
+ * the ACPI interpreter and keels over since IRQ 9 has not been
+ * setup as we had setup IRQ 20 for it).
+ */
+ if (gsi == acpi_sci_override_gsi) {
+ /* Check whether the GSI != IRQ */
+ acpi_gsi_to_irq(gsi, &irq);
+ if (irq != gsi)
+ /* Bugger, we MUST have that IRQ. */
+ gsi_override = true;
+ }
+ if (gsi_override)
+ irq = xen_bind_pirq_gsi_to_irq(irq, pirq, shareable, name);
+ else
+ irq = xen_bind_pirq_gsi_to_irq(gsi, pirq, shareable, name);
if (irq < 0)
goto out;
- printk(KERN_DEBUG "xen: --> pirq=%d -> irq=%d\n", pirq, irq);
+ printk(KERN_DEBUG "xen: --> pirq=%d -> irq=%d (gsi=%d)\n", pirq, irq, gsi);
map_irq.domid = DOMID_SELF;
map_irq.type = MAP_PIRQ_TYPE_GSI;
{
struct {
struct mmuext_op op;
+#ifdef CONFIG_SMP
DECLARE_BITMAP(mask, num_processors);
+#else
+ DECLARE_BITMAP(mask, NR_CPUS);
+#endif
} *args;
struct multicall_space mcs;
bio_list_init(&bio_list_on_stack);
- throtl_log(td, "dispatch nr_queued=%lu read=%u write=%u",
+ throtl_log(td, "dispatch nr_queued=%d read=%u write=%u",
total_nr_queued(td), td->nr_queued[READ],
td->nr_queued[WRITE]);
}
queue_bio:
- throtl_log_tg(td, tg, "[%c] bio. bdisp=%u sz=%u bps=%llu"
+ throtl_log_tg(td, tg, "[%c] bio. bdisp=%llu sz=%u bps=%llu"
" iodisp=%u iops=%u queued=%d/%d",
rw == READ ? 'R' : 'W',
tg->bytes_disp[rw], bio->bi_size, tg->bps[rw],
cfq_log_cfqg(cfqd, cfqg, "served: vt=%llu min_vt=%llu", cfqg->vdisktime,
st->min_vdisktime);
- cfq_log_cfqq(cfqq->cfqd, cfqq, "sl_used=%u disp=%u charge=%u iops=%u"
- " sect=%u", used_sl, cfqq->slice_dispatch, charge,
- iops_mode(cfqd), cfqq->nr_sectors);
+ cfq_log_cfqq(cfqq->cfqd, cfqq,
+ "sl_used=%u disp=%u charge=%u iops=%u sect=%lu",
+ used_sl, cfqq->slice_dispatch, charge,
+ iops_mode(cfqd), cfqq->nr_sectors);
cfq_blkiocg_update_timeslice_used(&cfqg->blkg, used_sl,
unaccounted_sl);
cfq_blkiocg_set_start_empty_time(&cfqg->blkg);
*/
if (sample_valid(cic->ttime_samples) &&
(cfqq->slice_end - jiffies < cic->ttime_mean)) {
- cfq_log_cfqq(cfqd, cfqq, "Not idling. think_time:%d",
- cic->ttime_mean);
+ cfq_log_cfqq(cfqd, cfqq, "Not idling. think_time:%lu",
+ cic->ttime_mean);
return;
}
smp_wmb();
cic->key = cfqd_dead_key(cfqd);
- if (ioc->ioc_data == cic)
+ if (rcu_dereference(ioc->ioc_data) == cic) {
+ spin_lock(&ioc->lock);
rcu_assign_pointer(ioc->ioc_data, NULL);
+ spin_unlock(&ioc->lock);
+ }
if (cic->cfqq[BLK_RW_ASYNC]) {
cfq_exit_cfqq(cfqd, cic->cfqq[BLK_RW_ASYNC]);
struct gendisk *disk; /* the associated disk */
spinlock_t lock;
+ struct mutex block_mutex; /* protects blocking */
int block; /* event blocking depth */
unsigned int pending; /* events already sent out */
unsigned int clearing; /* events being cleared */
return msecs_to_jiffies(intv_msecs);
}
-static void __disk_block_events(struct gendisk *disk, bool sync)
+/**
+ * disk_block_events - block and flush disk event checking
+ * @disk: disk to block events for
+ *
+ * On return from this function, it is guaranteed that event checking
+ * isn't in progress and won't happen until unblocked by
+ * disk_unblock_events(). Events blocking is counted and the actual
+ * unblocking happens after the matching number of unblocks are done.
+ *
+ * Note that this intentionally does not block event checking from
+ * disk_clear_events().
+ *
+ * CONTEXT:
+ * Might sleep.
+ */
+void disk_block_events(struct gendisk *disk)
{
struct disk_events *ev = disk->ev;
unsigned long flags;
bool cancel;
+ if (!ev)
+ return;
+
+ /*
+ * Outer mutex ensures that the first blocker completes canceling
+ * the event work before further blockers are allowed to finish.
+ */
+ mutex_lock(&ev->block_mutex);
+
spin_lock_irqsave(&ev->lock, flags);
cancel = !ev->block++;
spin_unlock_irqrestore(&ev->lock, flags);
- if (cancel) {
- if (sync)
- cancel_delayed_work_sync(&disk->ev->dwork);
- else
- cancel_delayed_work(&disk->ev->dwork);
- }
+ if (cancel)
+ cancel_delayed_work_sync(&disk->ev->dwork);
+
+ mutex_unlock(&ev->block_mutex);
}
static void __disk_unblock_events(struct gendisk *disk, bool check_now)
}
/**
- * disk_block_events - block and flush disk event checking
- * @disk: disk to block events for
- *
- * On return from this function, it is guaranteed that event checking
- * isn't in progress and won't happen until unblocked by
- * disk_unblock_events(). Events blocking is counted and the actual
- * unblocking happens after the matching number of unblocks are done.
- *
- * Note that this intentionally does not block event checking from
- * disk_clear_events().
- *
- * CONTEXT:
- * Might sleep.
- */
-void disk_block_events(struct gendisk *disk)
-{
- if (disk->ev)
- __disk_block_events(disk, true);
-}
-
-/**
* disk_unblock_events - unblock disk event checking
* @disk: disk to unblock events for
*
*/
void disk_check_events(struct gendisk *disk)
{
- if (disk->ev) {
- __disk_block_events(disk, false);
- __disk_unblock_events(disk, true);
+ struct disk_events *ev = disk->ev;
+ unsigned long flags;
+
+ if (!ev)
+ return;
+
+ spin_lock_irqsave(&ev->lock, flags);
+ if (!ev->block) {
+ cancel_delayed_work(&ev->dwork);
+ queue_delayed_work(system_nrt_wq, &ev->dwork, 0);
}
+ spin_unlock_irqrestore(&ev->lock, flags);
}
EXPORT_SYMBOL_GPL(disk_check_events);
spin_unlock_irq(&ev->lock);
/* uncondtionally schedule event check and wait for it to finish */
- __disk_block_events(disk, true);
+ disk_block_events(disk);
queue_delayed_work(system_nrt_wq, &ev->dwork, 0);
flush_delayed_work(&ev->dwork);
__disk_unblock_events(disk, false);
if (intv < 0 && intv != -1)
return -EINVAL;
- __disk_block_events(disk, true);
+ disk_block_events(disk);
disk->ev->poll_msecs = intv;
__disk_unblock_events(disk, true);
INIT_LIST_HEAD(&ev->node);
ev->disk = disk;
spin_lock_init(&ev->lock);
+ mutex_init(&ev->block_mutex);
ev->block = 1;
ev->poll_msecs = -1;
INIT_DELAYED_WORK(&ev->dwork, disk_events_workfn);
if (!disk->ev)
return;
- __disk_block_events(disk, true);
+ disk_block_events(disk);
mutex_lock(&disk_events_mutex);
list_del_init(&disk->ev->node);
#include <linux/interrupt.h>
#include <linux/mm.h>
#include <linux/net.h>
-#include <linux/slab.h>
#define DEFLATE_DEF_LEVEL Z_DEFAULT_COMPRESSION
#define DEFLATE_DEF_WINBITS 11
int ret = 0;
struct z_stream_s *stream = &ctx->decomp_stream;
- stream->workspace = kzalloc(zlib_inflate_workspacesize(), GFP_KERNEL);
+ stream->workspace = vzalloc(zlib_inflate_workspacesize());
if (!stream->workspace) {
ret = -ENOMEM;
goto out;
out:
return ret;
out_free:
- kfree(stream->workspace);
+ vfree(stream->workspace);
goto out;
}
static void deflate_decomp_exit(struct deflate_ctx *ctx)
{
zlib_inflateEnd(&ctx->decomp_stream);
- kfree(ctx->decomp_stream.workspace);
+ vfree(ctx->decomp_stream.workspace);
}
static int deflate_init(struct crypto_tfm *tfm)
#include <linux/interrupt.h>
#include <linux/mm.h>
#include <linux/net.h>
-#include <linux/slab.h>
#include <crypto/internal/compress.h>
if (stream->workspace) {
zlib_inflateEnd(stream);
- kfree(stream->workspace);
+ vfree(stream->workspace);
stream->workspace = NULL;
}
}
? nla_get_u32(tb[ZLIB_DECOMP_WINDOWBITS])
: DEF_WBITS;
- stream->workspace = kzalloc(zlib_inflate_workspacesize(), GFP_KERNEL);
+ stream->workspace = vzalloc(zlib_inflate_workspacesize());
if (!stream->workspace)
return -ENOMEM;
ret = zlib_inflateInit2(stream, ctx->decomp_windowBits);
if (ret != Z_OK) {
- kfree(stream->workspace);
+ vfree(stream->workspace);
stream->workspace = NULL;
return -EINVAL;
}
}
if (mask_port_map) {
- dev_printk(KERN_ERR, dev, "masking port_map 0x%x -> 0x%x\n",
+ dev_printk(KERN_WARNING, dev, "masking port_map 0x%x -> 0x%x\n",
port_map,
port_map & mask_port_map);
port_map &= mask_port_map;
* Devices which choke on SETXFER. Applies only if both the
* device and controller are SATA.
*/
- { "PIONEER DVD-RW DVRTD08", "1.00", ATA_HORKAGE_NOSETXFER },
- { "PIONEER DVD-RW DVR-212D", "1.28", ATA_HORKAGE_NOSETXFER },
- { "PIONEER DVD-RW DVR-216D", "1.08", ATA_HORKAGE_NOSETXFER },
+ { "PIONEER DVD-RW DVRTD08", NULL, ATA_HORKAGE_NOSETXFER },
+ { "PIONEER DVD-RW DVR-212D", NULL, ATA_HORKAGE_NOSETXFER },
+ { "PIONEER DVD-RW DVR-216D", NULL, ATA_HORKAGE_NOSETXFER },
/* End Marker */
{ }
*/
int ata_sas_port_start(struct ata_port *ap)
{
+ /*
+ * the port is marked as frozen at allocation time, but if we don't
+ * have new eh, we won't thaw it
+ */
+ if (!ap->ops->error_handler)
+ ap->pflags &= ~ATA_PFLAG_FROZEN;
return 0;
}
EXPORT_SYMBOL_GPL(ata_sas_port_start);
{ PCI_DEVICE(0x11AB, 0x6121), },
{ PCI_DEVICE(0x11AB, 0x6123), },
{ PCI_DEVICE(0x11AB, 0x6145), },
+ { PCI_DEVICE(0x1B4B, 0x91A0), },
+ { PCI_DEVICE(0x1B4B, 0x91A4), },
+
{ } /* terminate list */
};
/*
* Function: get_burst_length_encode
* arguments: datalength: length in bytes of data
- * returns value to be programmed in register corrresponding to data length
+ * returns value to be programmed in register corresponding to data length
* This value is effectively the log(base 2) of the length
*/
static int get_burst_length_encode(int datalength)
*
* Returns &struct platform_device pointer on success, or ERR_PTR() on error.
*/
-struct platform_device *__init_or_module platform_device_register_resndata(
+struct platform_device *platform_device_register_resndata(
struct device *parent,
const char *name, int id,
const struct resource *res, unsigned int num,
spin_unlock_bh(&dev->cbdev->queue_lock);
if (cbq != NULL) {
+ err = 0;
cbq->callback(msg, nsp);
kfree_skb(skb);
cn_queue_release_callback(cbq);
/* build shared descriptor for this session */
sh_desc = kmalloc(CAAM_CMD_SZ * DESC_AEAD_SHARED_TEXT_LEN +
- keys_fit_inline ?
- ctx->split_key_pad_len + ctx->enckeylen :
- CAAM_PTR_SZ * 2, GFP_DMA | GFP_KERNEL);
+ (keys_fit_inline ?
+ ctx->split_key_pad_len + ctx->enckeylen :
+ CAAM_PTR_SZ * 2), GFP_DMA | GFP_KERNEL);
if (!sh_desc) {
dev_err(jrdev, "could not allocate shared descriptor\n");
return -ENOMEM;
config GOOGLE_SMI
tristate "SMI interface for Google platforms"
depends on ACPI && DMI
+ select EFI
select EFI_VARS
help
Say Y here if you want to enable SMI callbacks for Google
#include <linux/module.h>
#include <linux/mman.h>
#include <linux/pagemap.h>
+#include <linux/shmem_fs.h>
#include "drmP.h"
/** @file drm_gem.c
if (ret)
return ret;
- seq_printf(m, "power context ");
- describe_obj(m, dev_priv->pwrctx);
- seq_printf(m, "\n");
+ if (dev_priv->pwrctx) {
+ seq_printf(m, "power context ");
+ describe_obj(m, dev_priv->pwrctx);
+ seq_printf(m, "\n");
+ }
- seq_printf(m, "render context ");
- describe_obj(m, dev_priv->renderctx);
- seq_printf(m, "\n");
+ if (dev_priv->renderctx) {
+ seq_printf(m, "render context ");
+ describe_obj(m, dev_priv->renderctx);
+ seq_printf(m, "\n");
+ }
mutex_unlock(&dev->mode_config.mutex);
intel_modeset_gem_init(dev);
- if (IS_IVYBRIDGE(dev)) {
- /* Share pre & uninstall handlers with ILK/SNB */
- dev->driver->irq_handler = ivybridge_irq_handler;
- dev->driver->irq_preinstall = ironlake_irq_preinstall;
- dev->driver->irq_postinstall = ivybridge_irq_postinstall;
- dev->driver->irq_uninstall = ironlake_irq_uninstall;
- dev->driver->enable_vblank = ivybridge_enable_vblank;
- dev->driver->disable_vblank = ivybridge_disable_vblank;
- } else if (HAS_PCH_SPLIT(dev)) {
- dev->driver->irq_handler = ironlake_irq_handler;
- dev->driver->irq_preinstall = ironlake_irq_preinstall;
- dev->driver->irq_postinstall = ironlake_irq_postinstall;
- dev->driver->irq_uninstall = ironlake_irq_uninstall;
- dev->driver->enable_vblank = ironlake_enable_vblank;
- dev->driver->disable_vblank = ironlake_disable_vblank;
- } else {
- dev->driver->irq_preinstall = i915_driver_irq_preinstall;
- dev->driver->irq_postinstall = i915_driver_irq_postinstall;
- dev->driver->irq_uninstall = i915_driver_irq_uninstall;
- dev->driver->irq_handler = i915_driver_irq_handler;
- dev->driver->enable_vblank = i915_enable_vblank;
- dev->driver->disable_vblank = i915_disable_vblank;
- }
-
ret = drm_irq_install(dev);
if (ret)
goto cleanup_gem;
/* enable GEM by default */
dev_priv->has_gem = 1;
- dev->driver->get_vblank_counter = i915_get_vblank_counter;
- dev->max_vblank_count = 0xffffff; /* only 24 bits of frame count */
- if (IS_G4X(dev) || IS_GEN5(dev) || IS_GEN6(dev) || IS_IVYBRIDGE(dev)) {
- dev->max_vblank_count = 0xffffffff; /* full 32 bit counter */
- dev->driver->get_vblank_counter = gm45_get_vblank_counter;
- }
+ intel_irq_init(dev);
/* Try to make sure MCHBAR is enabled before poking at it */
intel_setup_mchbar(dev);
/* Flush any outstanding unpin_work. */
flush_workqueue(dev_priv->wq);
- i915_gem_free_all_phys_object(dev);
-
mutex_lock(&dev->struct_mutex);
+ i915_gem_free_all_phys_object(dev);
i915_gem_cleanup_ringbuffer(dev);
mutex_unlock(&dev->struct_mutex);
if (I915_HAS_FBC(dev) && i915_powersave)
} else switch (INTEL_INFO(dev)->gen) {
case 6:
ret = gen6_do_reset(dev, flags);
+ /* If reset with a user forcewake, try to restore */
+ if (atomic_read(&dev_priv->forcewake_count))
+ __gen6_gt_force_wake_get(dev_priv);
break;
case 5:
ret = ironlake_do_reset(dev, flags);
.resume = i915_resume,
.device_is_agp = i915_driver_device_is_agp,
- .enable_vblank = i915_enable_vblank,
- .disable_vblank = i915_disable_vblank,
- .get_vblank_timestamp = i915_get_vblank_timestamp,
- .get_scanout_position = i915_get_crtc_scanoutpos,
- .irq_preinstall = i915_driver_irq_preinstall,
- .irq_postinstall = i915_driver_irq_postinstall,
- .irq_uninstall = i915_driver_irq_uninstall,
- .irq_handler = i915_driver_irq_handler,
.reclaim_buffers = drm_core_reclaim_buffers,
.master_create = i915_master_create,
.master_destroy = i915_master_destroy,
void (*fdi_link_train)(struct drm_crtc *crtc);
void (*init_clock_gating)(struct drm_device *dev);
void (*init_pch_clock_gating)(struct drm_device *dev);
+ int (*queue_flip)(struct drm_device *dev, struct drm_crtc *crtc,
+ struct drm_framebuffer *fb,
+ struct drm_i915_gem_object *obj);
/* clock updates for mode set */
/* cursor updates */
/* render clock increase/decrease */
extern int i915_suspend(struct drm_device *dev, pm_message_t state);
extern int i915_resume(struct drm_device *dev);
-extern void i915_save_display(struct drm_device *dev);
-extern void i915_restore_display(struct drm_device *dev);
extern int i915_master_create(struct drm_device *dev, struct drm_master *master);
extern void i915_master_destroy(struct drm_device *dev, struct drm_master *master);
extern int i915_irq_wait(struct drm_device *dev, void *data,
struct drm_file *file_priv);
-extern irqreturn_t i915_driver_irq_handler(DRM_IRQ_ARGS);
-extern void i915_driver_irq_preinstall(struct drm_device * dev);
-extern int i915_driver_irq_postinstall(struct drm_device *dev);
-extern void i915_driver_irq_uninstall(struct drm_device * dev);
-
-extern irqreturn_t ironlake_irq_handler(DRM_IRQ_ARGS);
-extern void ironlake_irq_preinstall(struct drm_device *dev);
-extern int ironlake_irq_postinstall(struct drm_device *dev);
-extern void ironlake_irq_uninstall(struct drm_device *dev);
-
-extern irqreturn_t ivybridge_irq_handler(DRM_IRQ_ARGS);
-extern void ivybridge_irq_preinstall(struct drm_device *dev);
-extern int ivybridge_irq_postinstall(struct drm_device *dev);
-extern void ivybridge_irq_uninstall(struct drm_device *dev);
+extern void intel_irq_init(struct drm_device *dev);
extern int i915_vblank_pipe_set(struct drm_device *dev, void *data,
struct drm_file *file_priv);
extern int i915_vblank_pipe_get(struct drm_device *dev, void *data,
struct drm_file *file_priv);
-extern int i915_enable_vblank(struct drm_device *dev, int crtc);
-extern void i915_disable_vblank(struct drm_device *dev, int crtc);
-extern int ironlake_enable_vblank(struct drm_device *dev, int crtc);
-extern void ironlake_disable_vblank(struct drm_device *dev, int crtc);
-extern int ivybridge_enable_vblank(struct drm_device *dev, int crtc);
-extern void ivybridge_disable_vblank(struct drm_device *dev, int crtc);
-extern u32 i915_get_vblank_counter(struct drm_device *dev, int crtc);
-extern u32 gm45_get_vblank_counter(struct drm_device *dev, int crtc);
extern int i915_vblank_swap(struct drm_device *dev, void *data,
struct drm_file *file_priv);
i915_disable_pipestat(drm_i915_private_t *dev_priv, int pipe, u32 mask);
void intel_enable_asle (struct drm_device *dev);
-int i915_get_vblank_timestamp(struct drm_device *dev, int crtc,
- int *max_error,
- struct timeval *vblank_time,
- unsigned flags);
-
-int i915_get_crtc_scanoutpos(struct drm_device *dev, int pipe,
- int *vpos, int *hpos);
#ifdef CONFIG_DEBUG_FS
extern void i915_destroy_error_state(struct drm_device *dev);
#include "i915_drv.h"
#include "i915_trace.h"
#include "intel_drv.h"
+#include <linux/shmem_fs.h>
#include <linux/slab.h>
#include <linux/swap.h>
#include <linux/pci.h>
if ((page_offset + remain) > PAGE_SIZE)
page_length = PAGE_SIZE - page_offset;
- page = read_cache_page_gfp(mapping, offset >> PAGE_SHIFT,
- GFP_HIGHUSER | __GFP_RECLAIMABLE);
+ page = shmem_read_mapping_page(mapping, offset >> PAGE_SHIFT);
if (IS_ERR(page))
return PTR_ERR(page);
if ((data_page_offset + page_length) > PAGE_SIZE)
page_length = PAGE_SIZE - data_page_offset;
- page = read_cache_page_gfp(mapping, offset >> PAGE_SHIFT,
- GFP_HIGHUSER | __GFP_RECLAIMABLE);
+ page = shmem_read_mapping_page(mapping, offset >> PAGE_SHIFT);
if (IS_ERR(page)) {
ret = PTR_ERR(page);
goto out;
if ((page_offset + remain) > PAGE_SIZE)
page_length = PAGE_SIZE - page_offset;
- page = read_cache_page_gfp(mapping, offset >> PAGE_SHIFT,
- GFP_HIGHUSER | __GFP_RECLAIMABLE);
+ page = shmem_read_mapping_page(mapping, offset >> PAGE_SHIFT);
if (IS_ERR(page))
return PTR_ERR(page);
if ((data_page_offset + page_length) > PAGE_SIZE)
page_length = PAGE_SIZE - data_page_offset;
- page = read_cache_page_gfp(mapping, offset >> PAGE_SHIFT,
- GFP_HIGHUSER | __GFP_RECLAIMABLE);
+ page = shmem_read_mapping_page(mapping, offset >> PAGE_SHIFT);
if (IS_ERR(page)) {
ret = PTR_ERR(page);
goto out;
ret = i915_gem_object_bind_to_gtt(obj, 0, true);
if (ret)
goto unlock;
- }
- ret = i915_gem_object_set_to_gtt_domain(obj, write);
- if (ret)
- goto unlock;
+ ret = i915_gem_object_set_to_gtt_domain(obj, write);
+ if (ret)
+ goto unlock;
+ }
if (obj->tiling_mode == I915_TILING_NONE)
ret = i915_gem_object_put_fence(obj);
inode = obj->base.filp->f_path.dentry->d_inode;
mapping = inode->i_mapping;
+ gfpmask |= mapping_gfp_mask(mapping);
+
for (i = 0; i < page_count; i++) {
- page = read_cache_page_gfp(mapping, i,
- GFP_HIGHUSER |
- __GFP_COLD |
- __GFP_RECLAIMABLE |
- gfpmask);
+ page = shmem_read_mapping_page_gfp(mapping, i, gfpmask);
if (IS_ERR(page))
goto err_pages;
/* Our goal here is to return as much of the memory as
* is possible back to the system as we are called from OOM.
* To do this we must instruct the shmfs to drop all of its
- * backing pages, *now*. Here we mirror the actions taken
- * when by shmem_delete_inode() to release the backing store.
+ * backing pages, *now*.
*/
inode = obj->base.filp->f_path.dentry->d_inode;
- truncate_inode_pages(inode->i_mapping, 0);
- if (inode->i_op->truncate_range)
- inode->i_op->truncate_range(inode, 0, (loff_t)-1);
+ shmem_truncate_range(inode, 0, (loff_t)-1);
obj->madv = __I915_MADV_PURGED;
}
if (!ier) {
DRM_ERROR("something (likely vbetool) disabled "
"interrupts, re-enabling\n");
- i915_driver_irq_preinstall(ring->dev);
- i915_driver_irq_postinstall(ring->dev);
+ ring->dev->driver->irq_preinstall(ring->dev);
+ ring->dev->driver->irq_postinstall(ring->dev);
}
trace_i915_gem_request_wait_begin(ring, seqno);
*/
wmb();
- i915_gem_release_mmap(obj);
-
old_write_domain = obj->base.write_domain;
obj->base.write_domain = 0;
{
struct drm_i915_private *dev_priv = dev->dev_private;
struct drm_i915_gem_object *obj;
+ struct address_space *mapping;
obj = kzalloc(sizeof(*obj), GFP_KERNEL);
if (obj == NULL)
return NULL;
}
+ mapping = obj->base.filp->f_path.dentry->d_inode->i_mapping;
+ mapping_set_gfp_mask(mapping, GFP_HIGHUSER | __GFP_RECLAIMABLE);
+
i915_gem_info_add_obj(dev_priv, size);
obj->base.write_domain = I915_GEM_DOMAIN_CPU;
page_count = obj->base.size / PAGE_SIZE;
for (i = 0; i < page_count; i++) {
- struct page *page = read_cache_page_gfp(mapping, i,
- GFP_HIGHUSER | __GFP_RECLAIMABLE);
+ struct page *page = shmem_read_mapping_page(mapping, i);
if (!IS_ERR(page)) {
char *dst = kmap_atomic(page);
memcpy(dst, vaddr + i*PAGE_SIZE, PAGE_SIZE);
struct page *page;
char *dst, *src;
- page = read_cache_page_gfp(mapping, i,
- GFP_HIGHUSER | __GFP_RECLAIMABLE);
+ page = shmem_read_mapping_page(mapping, i);
if (IS_ERR(page))
return PTR_ERR(page);
if ((flush_domains | invalidate_domains) & I915_GEM_DOMAIN_CPU)
i915_gem_clflush_object(obj);
- /* blow away mappings if mapped through GTT */
- if ((flush_domains | invalidate_domains) & I915_GEM_DOMAIN_GTT)
- i915_gem_release_mmap(obj);
-
if (obj->base.pending_write_domain)
cd->flips |= atomic_read(&obj->pending_flip);
/* Called from drm generic code, passed a 'crtc', which
* we use as a pipe index
*/
-u32 i915_get_vblank_counter(struct drm_device *dev, int pipe)
+static u32 i915_get_vblank_counter(struct drm_device *dev, int pipe)
{
drm_i915_private_t *dev_priv = (drm_i915_private_t *) dev->dev_private;
unsigned long high_frame;
return (high1 << 8) | low;
}
-u32 gm45_get_vblank_counter(struct drm_device *dev, int pipe)
+static u32 gm45_get_vblank_counter(struct drm_device *dev, int pipe)
{
drm_i915_private_t *dev_priv = (drm_i915_private_t *) dev->dev_private;
int reg = PIPE_FRMCOUNT_GM45(pipe);
return I915_READ(reg);
}
-int i915_get_crtc_scanoutpos(struct drm_device *dev, int pipe,
+static int i915_get_crtc_scanoutpos(struct drm_device *dev, int pipe,
int *vpos, int *hpos)
{
drm_i915_private_t *dev_priv = (drm_i915_private_t *) dev->dev_private;
return ret;
}
-int i915_get_vblank_timestamp(struct drm_device *dev, int pipe,
+static int i915_get_vblank_timestamp(struct drm_device *dev, int pipe,
int *max_error,
struct timeval *vblank_time,
unsigned flags)
DRM_DEBUG_DRIVER("PCH transcoder A underrun interrupt\n");
}
-irqreturn_t ivybridge_irq_handler(DRM_IRQ_ARGS)
+static irqreturn_t ivybridge_irq_handler(DRM_IRQ_ARGS)
{
struct drm_device *dev = (struct drm_device *) arg;
drm_i915_private_t *dev_priv = (drm_i915_private_t *) dev->dev_private;
return ret;
}
-irqreturn_t ironlake_irq_handler(DRM_IRQ_ARGS)
+static irqreturn_t ironlake_irq_handler(DRM_IRQ_ARGS)
{
struct drm_device *dev = (struct drm_device *) arg;
drm_i915_private_t *dev_priv = (drm_i915_private_t *) dev->dev_private;
}
}
-irqreturn_t i915_driver_irq_handler(DRM_IRQ_ARGS)
+static irqreturn_t i915_driver_irq_handler(DRM_IRQ_ARGS)
{
struct drm_device *dev = (struct drm_device *) arg;
drm_i915_private_t *dev_priv = (drm_i915_private_t *) dev->dev_private;
/* Called from drm generic code, passed 'crtc' which
* we use as a pipe index
*/
-int i915_enable_vblank(struct drm_device *dev, int pipe)
+static int i915_enable_vblank(struct drm_device *dev, int pipe)
{
drm_i915_private_t *dev_priv = (drm_i915_private_t *) dev->dev_private;
unsigned long irqflags;
return 0;
}
-int ironlake_enable_vblank(struct drm_device *dev, int pipe)
+static int ironlake_enable_vblank(struct drm_device *dev, int pipe)
{
drm_i915_private_t *dev_priv = (drm_i915_private_t *) dev->dev_private;
unsigned long irqflags;
return 0;
}
-int ivybridge_enable_vblank(struct drm_device *dev, int pipe)
+static int ivybridge_enable_vblank(struct drm_device *dev, int pipe)
{
drm_i915_private_t *dev_priv = (drm_i915_private_t *) dev->dev_private;
unsigned long irqflags;
/* Called from drm generic code, passed 'crtc' which
* we use as a pipe index
*/
-void i915_disable_vblank(struct drm_device *dev, int pipe)
+static void i915_disable_vblank(struct drm_device *dev, int pipe)
{
drm_i915_private_t *dev_priv = (drm_i915_private_t *) dev->dev_private;
unsigned long irqflags;
spin_unlock_irqrestore(&dev_priv->irq_lock, irqflags);
}
-void ironlake_disable_vblank(struct drm_device *dev, int pipe)
+static void ironlake_disable_vblank(struct drm_device *dev, int pipe)
{
drm_i915_private_t *dev_priv = (drm_i915_private_t *) dev->dev_private;
unsigned long irqflags;
spin_unlock_irqrestore(&dev_priv->irq_lock, irqflags);
}
-void ivybridge_disable_vblank(struct drm_device *dev, int pipe)
+static void ivybridge_disable_vblank(struct drm_device *dev, int pipe)
{
drm_i915_private_t *dev_priv = (drm_i915_private_t *) dev->dev_private;
unsigned long irqflags;
/* drm_dma.h hooks
*/
-void ironlake_irq_preinstall(struct drm_device *dev)
+static void ironlake_irq_preinstall(struct drm_device *dev)
{
drm_i915_private_t *dev_priv = (drm_i915_private_t *) dev->dev_private;
INIT_WORK(&dev_priv->rps_work, gen6_pm_rps_work);
I915_WRITE(HWSTAM, 0xeffe);
- if (IS_GEN6(dev)) {
+ if (IS_GEN6(dev) || IS_GEN7(dev)) {
/* Workaround stalls observed on Sandy Bridge GPUs by
* making the blitter command streamer generate a
* write to the Hardware Status Page for
* happens.
*/
I915_WRITE(GEN6_BLITTER_HWSTAM, ~GEN6_BLITTER_USER_INTERRUPT);
+ I915_WRITE(GEN6_BSD_HWSTAM, ~GEN6_BSD_USER_INTERRUPT);
}
/* XXX hotplug from PCH */
POSTING_READ(SDEIER);
}
-int ironlake_irq_postinstall(struct drm_device *dev)
+static int ironlake_irq_postinstall(struct drm_device *dev)
{
drm_i915_private_t *dev_priv = (drm_i915_private_t *) dev->dev_private;
/* enable kind of interrupts always enabled */
return 0;
}
-int ivybridge_irq_postinstall(struct drm_device *dev)
+static int ivybridge_irq_postinstall(struct drm_device *dev)
{
drm_i915_private_t *dev_priv = (drm_i915_private_t *) dev->dev_private;
/* enable kind of interrupts always enabled */
return 0;
}
-void i915_driver_irq_preinstall(struct drm_device * dev)
+static void i915_driver_irq_preinstall(struct drm_device * dev)
{
drm_i915_private_t *dev_priv = (drm_i915_private_t *) dev->dev_private;
int pipe;
* Must be called after intel_modeset_init or hotplug interrupts won't be
* enabled correctly.
*/
-int i915_driver_irq_postinstall(struct drm_device *dev)
+static int i915_driver_irq_postinstall(struct drm_device *dev)
{
drm_i915_private_t *dev_priv = (drm_i915_private_t *) dev->dev_private;
u32 enable_mask = I915_INTERRUPT_ENABLE_FIX | I915_INTERRUPT_ENABLE_VAR;
return 0;
}
-void ironlake_irq_uninstall(struct drm_device *dev)
+static void ironlake_irq_uninstall(struct drm_device *dev)
{
drm_i915_private_t *dev_priv = (drm_i915_private_t *) dev->dev_private;
I915_WRITE(GTIIR, I915_READ(GTIIR));
}
-void i915_driver_irq_uninstall(struct drm_device * dev)
+static void i915_driver_irq_uninstall(struct drm_device * dev)
{
drm_i915_private_t *dev_priv = (drm_i915_private_t *) dev->dev_private;
int pipe;
I915_READ(PIPESTAT(pipe)) & 0x8000ffff);
I915_WRITE(IIR, I915_READ(IIR));
}
+
+void intel_irq_init(struct drm_device *dev)
+{
+ dev->driver->get_vblank_counter = i915_get_vblank_counter;
+ dev->max_vblank_count = 0xffffff; /* only 24 bits of frame count */
+ if (IS_G4X(dev) || IS_GEN5(dev) || IS_GEN6(dev) || IS_IVYBRIDGE(dev)) {
+ dev->max_vblank_count = 0xffffffff; /* full 32 bit counter */
+ dev->driver->get_vblank_counter = gm45_get_vblank_counter;
+ }
+
+
+ dev->driver->get_vblank_timestamp = i915_get_vblank_timestamp;
+ dev->driver->get_scanout_position = i915_get_crtc_scanoutpos;
+
+ if (IS_IVYBRIDGE(dev)) {
+ /* Share pre & uninstall handlers with ILK/SNB */
+ dev->driver->irq_handler = ivybridge_irq_handler;
+ dev->driver->irq_preinstall = ironlake_irq_preinstall;
+ dev->driver->irq_postinstall = ivybridge_irq_postinstall;
+ dev->driver->irq_uninstall = ironlake_irq_uninstall;
+ dev->driver->enable_vblank = ivybridge_enable_vblank;
+ dev->driver->disable_vblank = ivybridge_disable_vblank;
+ } else if (HAS_PCH_SPLIT(dev)) {
+ dev->driver->irq_handler = ironlake_irq_handler;
+ dev->driver->irq_preinstall = ironlake_irq_preinstall;
+ dev->driver->irq_postinstall = ironlake_irq_postinstall;
+ dev->driver->irq_uninstall = ironlake_irq_uninstall;
+ dev->driver->enable_vblank = ironlake_enable_vblank;
+ dev->driver->disable_vblank = ironlake_disable_vblank;
+ } else {
+ dev->driver->irq_preinstall = i915_driver_irq_preinstall;
+ dev->driver->irq_postinstall = i915_driver_irq_postinstall;
+ dev->driver->irq_uninstall = i915_driver_irq_uninstall;
+ dev->driver->irq_handler = i915_driver_irq_handler;
+ dev->driver->enable_vblank = i915_enable_vblank;
+ dev->driver->disable_vblank = i915_disable_vblank;
+ }
+}
#define GEN6_BSD_SLEEP_PSMI_CONTROL_RC_ILDL_MESSAGE_ENABLE 0
#define GEN6_BSD_SLEEP_PSMI_CONTROL_IDLE_INDICATOR (1 << 3)
+#define GEN6_BSD_HWSTAM 0x12098
#define GEN6_BSD_IMR 0x120a8
#define GEN6_BSD_USER_INTERRUPT (1 << 12)
return;
}
-void i915_save_display(struct drm_device *dev)
+static void i915_save_display(struct drm_device *dev)
{
struct drm_i915_private *dev_priv = dev->dev_private;
i915_save_vga(dev);
}
-void i915_restore_display(struct drm_device *dev)
+static void i915_restore_display(struct drm_device *dev)
{
struct drm_i915_private *dev_priv = dev->dev_private;
I915_WRITE(CPU_VGACNTRL, dev_priv->saveVGACNTRL);
else
I915_WRITE(VGACNTRL, dev_priv->saveVGACNTRL);
+
I915_WRITE(VGA0, dev_priv->saveVGA0);
I915_WRITE(VGA1, dev_priv->saveVGA1);
I915_WRITE(VGA_PD, dev_priv->saveVGA_PD);
pci_read_config_byte(dev->pdev, LBB, &dev_priv->saveLBB);
+ mutex_lock(&dev->struct_mutex);
+
/* Hardware status page */
dev_priv->saveHWS = I915_READ(HWS_PGA);
for (i = 0; i < 3; i++)
dev_priv->saveSWF2[i] = I915_READ(SWF30 + (i << 2));
+ mutex_unlock(&dev->struct_mutex);
+
return 0;
}
pci_write_config_byte(dev->pdev, LBB, dev_priv->saveLBB);
+ mutex_lock(&dev->struct_mutex);
+
/* Hardware status page */
I915_WRITE(HWS_PGA, dev_priv->saveHWS);
I915_WRITE(IER, dev_priv->saveIER);
I915_WRITE(IMR, dev_priv->saveIMR);
}
+ mutex_unlock(&dev->struct_mutex);
intel_init_clock_gating(dev);
if (IS_GEN6(dev))
gen6_enable_rps(dev_priv);
+ mutex_lock(&dev->struct_mutex);
+
/* Cache mode state */
I915_WRITE (CACHE_MODE_0, dev_priv->saveCACHE_MODE_0 | 0xffff0000);
for (i = 0; i < 3; i++)
I915_WRITE(SWF30 + (i << 2), dev_priv->saveSWF2[i]);
+ mutex_unlock(&dev->struct_mutex);
+
intel_i2c_reset(dev);
return 0;
I915_WRITE(DSPCNTR(plane), dspcntr);
POSTING_READ(DSPCNTR(plane));
+ intel_enable_plane(dev_priv, plane, pipe);
ret = intel_pipe_set_base(crtc, x, y, old_fb);
I915_WRITE(DSPCNTR(plane), dspcntr);
POSTING_READ(DSPCNTR(plane));
- if (!HAS_PCH_SPLIT(dev))
- intel_enable_plane(dev_priv, plane, pipe);
ret = intel_pipe_set_base(crtc, x, y, old_fb);
spin_unlock_irqrestore(&dev->event_lock, flags);
}
+static int intel_gen2_queue_flip(struct drm_device *dev,
+ struct drm_crtc *crtc,
+ struct drm_framebuffer *fb,
+ struct drm_i915_gem_object *obj)
+{
+ struct drm_i915_private *dev_priv = dev->dev_private;
+ struct intel_crtc *intel_crtc = to_intel_crtc(crtc);
+ unsigned long offset;
+ u32 flip_mask;
+ int ret;
+
+ ret = intel_pin_and_fence_fb_obj(dev, obj, LP_RING(dev_priv));
+ if (ret)
+ goto out;
+
+ /* Offset into the new buffer for cases of shared fbs between CRTCs */
+ offset = crtc->y * fb->pitch + crtc->x * fb->bits_per_pixel/8;
+
+ ret = BEGIN_LP_RING(6);
+ if (ret)
+ goto out;
+
+ /* Can't queue multiple flips, so wait for the previous
+ * one to finish before executing the next.
+ */
+ if (intel_crtc->plane)
+ flip_mask = MI_WAIT_FOR_PLANE_B_FLIP;
+ else
+ flip_mask = MI_WAIT_FOR_PLANE_A_FLIP;
+ OUT_RING(MI_WAIT_FOR_EVENT | flip_mask);
+ OUT_RING(MI_NOOP);
+ OUT_RING(MI_DISPLAY_FLIP |
+ MI_DISPLAY_FLIP_PLANE(intel_crtc->plane));
+ OUT_RING(fb->pitch);
+ OUT_RING(obj->gtt_offset + offset);
+ OUT_RING(MI_NOOP);
+ ADVANCE_LP_RING();
+out:
+ return ret;
+}
+
+static int intel_gen3_queue_flip(struct drm_device *dev,
+ struct drm_crtc *crtc,
+ struct drm_framebuffer *fb,
+ struct drm_i915_gem_object *obj)
+{
+ struct drm_i915_private *dev_priv = dev->dev_private;
+ struct intel_crtc *intel_crtc = to_intel_crtc(crtc);
+ unsigned long offset;
+ u32 flip_mask;
+ int ret;
+
+ ret = intel_pin_and_fence_fb_obj(dev, obj, LP_RING(dev_priv));
+ if (ret)
+ goto out;
+
+ /* Offset into the new buffer for cases of shared fbs between CRTCs */
+ offset = crtc->y * fb->pitch + crtc->x * fb->bits_per_pixel/8;
+
+ ret = BEGIN_LP_RING(6);
+ if (ret)
+ goto out;
+
+ if (intel_crtc->plane)
+ flip_mask = MI_WAIT_FOR_PLANE_B_FLIP;
+ else
+ flip_mask = MI_WAIT_FOR_PLANE_A_FLIP;
+ OUT_RING(MI_WAIT_FOR_EVENT | flip_mask);
+ OUT_RING(MI_NOOP);
+ OUT_RING(MI_DISPLAY_FLIP_I915 |
+ MI_DISPLAY_FLIP_PLANE(intel_crtc->plane));
+ OUT_RING(fb->pitch);
+ OUT_RING(obj->gtt_offset + offset);
+ OUT_RING(MI_NOOP);
+
+ ADVANCE_LP_RING();
+out:
+ return ret;
+}
+
+static int intel_gen4_queue_flip(struct drm_device *dev,
+ struct drm_crtc *crtc,
+ struct drm_framebuffer *fb,
+ struct drm_i915_gem_object *obj)
+{
+ struct drm_i915_private *dev_priv = dev->dev_private;
+ struct intel_crtc *intel_crtc = to_intel_crtc(crtc);
+ uint32_t pf, pipesrc;
+ int ret;
+
+ ret = intel_pin_and_fence_fb_obj(dev, obj, LP_RING(dev_priv));
+ if (ret)
+ goto out;
+
+ ret = BEGIN_LP_RING(4);
+ if (ret)
+ goto out;
+
+ /* i965+ uses the linear or tiled offsets from the
+ * Display Registers (which do not change across a page-flip)
+ * so we need only reprogram the base address.
+ */
+ OUT_RING(MI_DISPLAY_FLIP |
+ MI_DISPLAY_FLIP_PLANE(intel_crtc->plane));
+ OUT_RING(fb->pitch);
+ OUT_RING(obj->gtt_offset | obj->tiling_mode);
+
+ /* XXX Enabling the panel-fitter across page-flip is so far
+ * untested on non-native modes, so ignore it for now.
+ * pf = I915_READ(pipe == 0 ? PFA_CTL_1 : PFB_CTL_1) & PF_ENABLE;
+ */
+ pf = 0;
+ pipesrc = I915_READ(PIPESRC(intel_crtc->pipe)) & 0x0fff0fff;
+ OUT_RING(pf | pipesrc);
+ ADVANCE_LP_RING();
+out:
+ return ret;
+}
+
+static int intel_gen6_queue_flip(struct drm_device *dev,
+ struct drm_crtc *crtc,
+ struct drm_framebuffer *fb,
+ struct drm_i915_gem_object *obj)
+{
+ struct drm_i915_private *dev_priv = dev->dev_private;
+ struct intel_crtc *intel_crtc = to_intel_crtc(crtc);
+ uint32_t pf, pipesrc;
+ int ret;
+
+ ret = intel_pin_and_fence_fb_obj(dev, obj, LP_RING(dev_priv));
+ if (ret)
+ goto out;
+
+ ret = BEGIN_LP_RING(4);
+ if (ret)
+ goto out;
+
+ OUT_RING(MI_DISPLAY_FLIP |
+ MI_DISPLAY_FLIP_PLANE(intel_crtc->plane));
+ OUT_RING(fb->pitch | obj->tiling_mode);
+ OUT_RING(obj->gtt_offset);
+
+ pf = I915_READ(PF_CTL(intel_crtc->pipe)) & PF_ENABLE;
+ pipesrc = I915_READ(PIPESRC(intel_crtc->pipe)) & 0x0fff0fff;
+ OUT_RING(pf | pipesrc);
+ ADVANCE_LP_RING();
+out:
+ return ret;
+}
+
+/*
+ * On gen7 we currently use the blit ring because (in early silicon at least)
+ * the render ring doesn't give us interrpts for page flip completion, which
+ * means clients will hang after the first flip is queued. Fortunately the
+ * blit ring generates interrupts properly, so use it instead.
+ */
+static int intel_gen7_queue_flip(struct drm_device *dev,
+ struct drm_crtc *crtc,
+ struct drm_framebuffer *fb,
+ struct drm_i915_gem_object *obj)
+{
+ struct drm_i915_private *dev_priv = dev->dev_private;
+ struct intel_crtc *intel_crtc = to_intel_crtc(crtc);
+ struct intel_ring_buffer *ring = &dev_priv->ring[BCS];
+ int ret;
+
+ ret = intel_pin_and_fence_fb_obj(dev, obj, ring);
+ if (ret)
+ goto out;
+
+ ret = intel_ring_begin(ring, 4);
+ if (ret)
+ goto out;
+
+ intel_ring_emit(ring, MI_DISPLAY_FLIP_I915 | (intel_crtc->plane << 19));
+ intel_ring_emit(ring, (fb->pitch | obj->tiling_mode));
+ intel_ring_emit(ring, (obj->gtt_offset));
+ intel_ring_emit(ring, (MI_NOOP));
+ intel_ring_advance(ring);
+out:
+ return ret;
+}
+
+static int intel_default_queue_flip(struct drm_device *dev,
+ struct drm_crtc *crtc,
+ struct drm_framebuffer *fb,
+ struct drm_i915_gem_object *obj)
+{
+ return -ENODEV;
+}
+
static int intel_crtc_page_flip(struct drm_crtc *crtc,
struct drm_framebuffer *fb,
struct drm_pending_vblank_event *event)
struct drm_i915_gem_object *obj;
struct intel_crtc *intel_crtc = to_intel_crtc(crtc);
struct intel_unpin_work *work;
- unsigned long flags, offset;
- int pipe = intel_crtc->pipe;
- u32 pf, pipesrc;
+ unsigned long flags;
int ret;
work = kzalloc(sizeof *work, GFP_KERNEL);
obj = intel_fb->obj;
mutex_lock(&dev->struct_mutex);
- ret = intel_pin_and_fence_fb_obj(dev, obj, LP_RING(dev_priv));
- if (ret)
- goto cleanup_work;
/* Reference the objects for the scheduled work. */
drm_gem_object_reference(&work->old_fb_obj->base);
if (ret)
goto cleanup_objs;
- if (IS_GEN3(dev) || IS_GEN2(dev)) {
- u32 flip_mask;
-
- /* Can't queue multiple flips, so wait for the previous
- * one to finish before executing the next.
- */
- ret = BEGIN_LP_RING(2);
- if (ret)
- goto cleanup_objs;
-
- if (intel_crtc->plane)
- flip_mask = MI_WAIT_FOR_PLANE_B_FLIP;
- else
- flip_mask = MI_WAIT_FOR_PLANE_A_FLIP;
- OUT_RING(MI_WAIT_FOR_EVENT | flip_mask);
- OUT_RING(MI_NOOP);
- ADVANCE_LP_RING();
- }
-
work->pending_flip_obj = obj;
work->enable_stall_check = true;
- /* Offset into the new buffer for cases of shared fbs between CRTCs */
- offset = crtc->y * fb->pitch + crtc->x * fb->bits_per_pixel/8;
-
- ret = BEGIN_LP_RING(4);
- if (ret)
- goto cleanup_objs;
-
/* Block clients from rendering to the new back buffer until
* the flip occurs and the object is no longer visible.
*/
atomic_add(1 << intel_crtc->plane, &work->old_fb_obj->pending_flip);
- switch (INTEL_INFO(dev)->gen) {
- case 2:
- OUT_RING(MI_DISPLAY_FLIP |
- MI_DISPLAY_FLIP_PLANE(intel_crtc->plane));
- OUT_RING(fb->pitch);
- OUT_RING(obj->gtt_offset + offset);
- OUT_RING(MI_NOOP);
- break;
-
- case 3:
- OUT_RING(MI_DISPLAY_FLIP_I915 |
- MI_DISPLAY_FLIP_PLANE(intel_crtc->plane));
- OUT_RING(fb->pitch);
- OUT_RING(obj->gtt_offset + offset);
- OUT_RING(MI_NOOP);
- break;
-
- case 4:
- case 5:
- /* i965+ uses the linear or tiled offsets from the
- * Display Registers (which do not change across a page-flip)
- * so we need only reprogram the base address.
- */
- OUT_RING(MI_DISPLAY_FLIP |
- MI_DISPLAY_FLIP_PLANE(intel_crtc->plane));
- OUT_RING(fb->pitch);
- OUT_RING(obj->gtt_offset | obj->tiling_mode);
-
- /* XXX Enabling the panel-fitter across page-flip is so far
- * untested on non-native modes, so ignore it for now.
- * pf = I915_READ(pipe == 0 ? PFA_CTL_1 : PFB_CTL_1) & PF_ENABLE;
- */
- pf = 0;
- pipesrc = I915_READ(PIPESRC(pipe)) & 0x0fff0fff;
- OUT_RING(pf | pipesrc);
- break;
-
- case 6:
- case 7:
- OUT_RING(MI_DISPLAY_FLIP |
- MI_DISPLAY_FLIP_PLANE(intel_crtc->plane));
- OUT_RING(fb->pitch | obj->tiling_mode);
- OUT_RING(obj->gtt_offset);
-
- pf = I915_READ(PF_CTL(pipe)) & PF_ENABLE;
- pipesrc = I915_READ(PIPESRC(pipe)) & 0x0fff0fff;
- OUT_RING(pf | pipesrc);
- break;
- }
- ADVANCE_LP_RING();
+ ret = dev_priv->display.queue_flip(dev, crtc, fb, obj);
+ if (ret)
+ goto cleanup_pending;
mutex_unlock(&dev->struct_mutex);
return 0;
+cleanup_pending:
+ atomic_sub(1 << intel_crtc->plane, &work->old_fb_obj->pending_flip);
cleanup_objs:
drm_gem_object_unreference(&work->old_fb_obj->base);
drm_gem_object_unreference(&obj->base);
-cleanup_work:
mutex_unlock(&dev->struct_mutex);
spin_lock_irqsave(&dev->event_lock, flags);
else
dev_priv->display.get_fifo_size = i830_get_fifo_size;
}
+
+ /* Default just returns -ENODEV to indicate unsupported */
+ dev_priv->display.queue_flip = intel_default_queue_flip;
+
+ switch (INTEL_INFO(dev)->gen) {
+ case 2:
+ dev_priv->display.queue_flip = intel_gen2_queue_flip;
+ break;
+
+ case 3:
+ dev_priv->display.queue_flip = intel_gen3_queue_flip;
+ break;
+
+ case 4:
+ case 5:
+ dev_priv->display.queue_flip = intel_gen4_queue_flip;
+ break;
+
+ case 6:
+ dev_priv->display.queue_flip = intel_gen6_queue_flip;
+ break;
+ case 7:
+ dev_priv->display.queue_flip = intel_gen7_queue_flip;
+ break;
+ }
}
/*
overlay = kzalloc(sizeof(struct intel_overlay), GFP_KERNEL);
if (!overlay)
return;
+
+ mutex_lock(&dev->struct_mutex);
+ if (WARN_ON(dev_priv->overlay))
+ goto out_free;
+
overlay->dev = dev;
reg_bo = i915_gem_alloc_object(dev, PAGE_SIZE);
regs = intel_overlay_map_regs(overlay);
if (!regs)
- goto out_free_bo;
+ goto out_unpin_bo;
memset(regs, 0, sizeof(struct overlay_registers));
update_polyphase_filter(regs);
intel_overlay_unmap_regs(overlay, regs);
dev_priv->overlay = overlay;
+ mutex_unlock(&dev->struct_mutex);
DRM_INFO("initialized overlay support\n");
return;
out_unpin_bo:
- i915_gem_object_unpin(reg_bo);
+ if (!OVERLAY_NEEDS_PHYSICAL(dev))
+ i915_gem_object_unpin(reg_bo);
out_free_bo:
drm_gem_object_unreference(®_bo->base);
out_free:
+ mutex_unlock(&dev->struct_mutex);
kfree(overlay);
return;
}
engine->vram.flags_valid = nv50_vram_flags_valid;
break;
case 0xC0:
- case 0xD0:
engine->instmem.init = nvc0_instmem_init;
engine->instmem.takedown = nvc0_instmem_takedown;
engine->instmem.suspend = nvc0_instmem_suspend;
dev_priv->card_type = NV_50;
break;
case 0xc0:
- case 0xd0:
dev_priv->card_type = NV_C0;
break;
default:
rdev->config.evergreen.tile_config |= (3 << 0);
break;
}
- /* num banks is 8 on all fusion asics */
+ /* num banks is 8 on all fusion asics. 0 = 4, 1 = 8, 2 = 16 */
if (rdev->flags & RADEON_IS_IGP)
- rdev->config.evergreen.tile_config |= 8 << 4;
+ rdev->config.evergreen.tile_config |= 1 << 4;
else
rdev->config.evergreen.tile_config |=
((mc_arb_ramcfg & NOOFBANK_MASK) >> NOOFBANK_SHIFT) << 4;
/* Get VRAM informations */
rdev->mc.vram_is_ddr = true;
- tmp = RREG32(MC_ARB_RAMCFG);
+ if (rdev->flags & RADEON_IS_IGP)
+ tmp = RREG32(FUS_MC_ARB_RAMCFG);
+ else
+ tmp = RREG32(MC_ARB_RAMCFG);
if (tmp & CHANSIZE_OVERRIDE) {
chansize = 16;
} else if (tmp & CHANSIZE_MASK) {
#define CGTS_USER_TCC_DISABLE 0x914C
#define TCC_DISABLE_MASK 0xFFFF0000
#define TCC_DISABLE_SHIFT 16
-#define CGTS_SM_CTRL_REG 0x915C
+#define CGTS_SM_CTRL_REG 0x9150
#define OVERRIDE (1 << 21)
#define TA_CNTL_AUX 0x9508
void radeon_combios_get_power_modes(struct radeon_device *rdev);
void radeon_atombios_get_power_modes(struct radeon_device *rdev);
void radeon_atom_set_voltage(struct radeon_device *rdev, u16 voltage_level, u8 voltage_type);
+int radeon_atom_get_max_vddc(struct radeon_device *rdev, u16 *voltage);
void rs690_pm_info(struct radeon_device *rdev);
extern int rv6xx_get_temp(struct radeon_device *rdev);
extern int rv770_get_temp(struct radeon_device *rdev);
le16_to_cpu(clock_info->r600.usVDDC);
}
+ /* patch up vddc if necessary */
+ if (rdev->pm.power_state[state_index].clock_info[mode_index].voltage.voltage == 0xff01) {
+ u16 vddc;
+
+ if (radeon_atom_get_max_vddc(rdev, &vddc) == 0)
+ rdev->pm.power_state[state_index].clock_info[mode_index].voltage.voltage = vddc;
+ }
+
if (rdev->flags & RADEON_IS_IGP) {
/* skip invalid modes */
if (rdev->pm.power_state[state_index].clock_info[mode_index].sclk == 0)
atom_execute_table(rdev->mode_info.atom_context, index, (uint32_t *)&args);
}
+int radeon_atom_get_max_vddc(struct radeon_device *rdev,
+ u16 *voltage)
+{
+ union set_voltage args;
+ int index = GetIndexIntoMasterTable(COMMAND, SetVoltage);
+ u8 frev, crev;
+
+ if (!atom_parse_cmd_header(rdev->mode_info.atom_context, index, &frev, &crev))
+ return -EINVAL;
+
+ switch (crev) {
+ case 1:
+ return -EINVAL;
+ case 2:
+ args.v2.ucVoltageType = SET_VOLTAGE_GET_MAX_VOLTAGE;
+ args.v2.ucVoltageMode = 0;
+ args.v2.usVoltageLevel = 0;
+
+ atom_execute_table(rdev->mode_info.atom_context, index, (uint32_t *)&args);
+
+ *voltage = le16_to_cpu(args.v2.usVoltageLevel);
+ break;
+ default:
+ DRM_ERROR("Unknown table version %d, %d\n", frev, crev);
+ return -EINVAL;
+ }
+ return 0;
+}
void radeon_atom_initialize_bios_scratch_regs(struct drm_device *dev)
{
static bool radeon_atrm_get_bios(struct radeon_device *rdev)
{
int ret;
- int size = 64 * 1024;
+ int size = 256 * 1024;
int i;
if (!radeon_atrm_supported(rdev->pdev))
else
tcp_chan_steer = 0x00fac688;
+ /* RV770 CE has special chremap setup */
+ if (rdev->pdev->device == 0x944e) {
+ tcp_chan_steer = 0x00b08b08;
+ mc_shared_chremap = 0x00b08b08;
+ }
+
WREG32(TCP_CHAN_STEER, tcp_chan_steer);
WREG32(MC_SHARED_CHREMAP, mc_shared_chremap);
}
#include <linux/sched.h>
#include <linux/highmem.h>
#include <linux/pagemap.h>
+#include <linux/shmem_fs.h>
#include <linux/file.h>
#include <linux/swap.h>
#include <linux/slab.h>
swap_space = swap_storage->f_path.dentry->d_inode->i_mapping;
for (i = 0; i < ttm->num_pages; ++i) {
- from_page = read_mapping_page(swap_space, i, NULL);
+ from_page = shmem_read_mapping_page(swap_space, i);
if (IS_ERR(from_page)) {
ret = PTR_ERR(from_page);
goto out_err;
from_page = ttm->pages[i];
if (unlikely(from_page == NULL))
continue;
- to_page = read_mapping_page(swap_space, i, NULL);
+ to_page = shmem_read_mapping_page(swap_space, i);
if (unlikely(IS_ERR(to_page))) {
ret = PTR_ERR(to_page);
goto out_err;
{ HID_USB_DEVICE(USB_VENDOR_ID_LOGITECH, USB_DEVICE_ID_SPACETRAVELLER) },
{ HID_USB_DEVICE(USB_VENDOR_ID_LOGITECH, USB_DEVICE_ID_SPACENAVIGATOR) },
{ HID_USB_DEVICE(USB_VENDOR_ID_LUMIO, USB_DEVICE_ID_CRYSTALTOUCH) },
+ { HID_USB_DEVICE(USB_VENDOR_ID_LUMIO, USB_DEVICE_ID_CRYSTALTOUCH_DUAL) },
{ HID_USB_DEVICE(USB_VENDOR_ID_MICROCHIP, USB_DEVICE_ID_PICOLCD) },
{ HID_USB_DEVICE(USB_VENDOR_ID_MICROCHIP, USB_DEVICE_ID_PICOLCD_BOOTLOADER) },
{ HID_USB_DEVICE(USB_VENDOR_ID_MICROSOFT, USB_DEVICE_ID_SIDEWINDER_GV) },
#define USB_VENDOR_ID_LUMIO 0x202e
#define USB_DEVICE_ID_CRYSTALTOUCH 0x0006
+#define USB_DEVICE_ID_CRYSTALTOUCH_DUAL 0x0007
#define USB_VENDOR_ID_MCC 0x09db
#define USB_DEVICE_ID_MCC_PMD1024LS 0x0076
}
return 1;
case HID_DG_CONTACTID:
+ if (!td->maxcontacts)
+ td->maxcontacts = MT_DEFAULT_MAXCONTACT;
input_mt_init_slots(hi->input, td->maxcontacts);
td->last_slot_field = usage->hid;
td->last_field_index = field->index;
if (ret)
goto fail;
- if (!td->maxcontacts)
- td->maxcontacts = MT_DEFAULT_MAXCONTACT;
-
td->slots = kzalloc(td->maxcontacts * sizeof(struct mt_slot),
GFP_KERNEL);
if (!td->slots) {
{ .driver_data = MT_CLS_CONFIDENCE_MINUS_ONE,
HID_USB_DEVICE(USB_VENDOR_ID_LUMIO,
USB_DEVICE_ID_CRYSTALTOUCH) },
+ { .driver_data = MT_CLS_CONFIDENCE_MINUS_ONE,
+ HID_USB_DEVICE(USB_VENDOR_ID_LUMIO,
+ USB_DEVICE_ID_CRYSTALTOUCH_DUAL) },
/* MosArt panels */
{ .driver_data = MT_CLS_CONFIDENCE_MINUS_ONE,
HID_USB_DEVICE(USB_VENDOR_ID_STANTUM,
USB_DEVICE_ID_MTP)},
{ .driver_data = MT_CLS_CONFIDENCE,
- HID_USB_DEVICE(USB_VENDOR_ID_STANTUM,
+ HID_USB_DEVICE(USB_VENDOR_ID_STANTUM_STM,
USB_DEVICE_ID_MTP_STM)},
{ .driver_data = MT_CLS_CONFIDENCE,
- HID_USB_DEVICE(USB_VENDOR_ID_STANTUM,
+ HID_USB_DEVICE(USB_VENDOR_ID_STANTUM_SITRONIX,
USB_DEVICE_ID_MTP_SITRONIX)},
/* Touch International panels */
F71858FG
F71862FG
F71863FG
- F71869F/E
+ F71869F/E/A
F71882FG
F71883FG
F71889FG/ED/A
const struct i2c_device_id *id)
{
int config;
+ int ret;
struct pmbus_driver_info *info;
if (!i2c_check_functionality(client->adapter,
return -ENOMEM;
config = i2c_smbus_read_byte_data(client, ADM1275_PMON_CONFIG);
- if (config < 0)
- return config;
+ if (config < 0) {
+ ret = config;
+ goto err_mem;
+ }
info->pages = 1;
info->direct[PSC_VOLTAGE_IN] = true;
else
info->func[0] |= PMBUS_HAVE_VIN | PMBUS_HAVE_STATUS_INPUT;
- return pmbus_do_probe(client, id, info);
+ ret = pmbus_do_probe(client, id, info);
+ if (ret)
+ goto err_mem;
+ return 0;
+
+err_mem:
+ kfree(info);
+ return ret;
}
static int adm1275_remove(struct i2c_client *client)
lsb = i2c_smbus_read_byte_data(client, reg);
msb = i2c_smbus_read_byte_data(client, reg + 1);
- if (lsb < 0 || msb < 0) {
- dev_err(&client->dev, "16-bit read failed at 0x%02x\n", reg);
+ if (unlikely(lsb < 0 || msb < 0)) {
+ dev_err(&client->dev, "%d-bit %s failed at 0x%02x\n",
+ 16, "read", reg);
return 0xFFFF; /* Arbitrary value */
}
int err;
err = i2c_smbus_write_byte_data(client, reg, val & 0xff);
- if (!err)
+ if (likely(!err))
err = i2c_smbus_write_byte_data(client, reg + 1, val >> 8);
- if (err < 0)
- dev_err(&client->dev, "16-bit write failed at 0x%02x\n", reg);
+ if (unlikely(err < 0))
+ dev_err(&client->dev, "%d-bit %s failed at 0x%02x\n",
+ 16, "write", reg);
+
+ return err;
+}
+
+/* Read 8-bit value from register */
+static u8 emc6w201_read8(struct i2c_client *client, u8 reg)
+{
+ int val;
+
+ val = i2c_smbus_read_byte_data(client, reg);
+ if (unlikely(val < 0)) {
+ dev_err(&client->dev, "%d-bit %s failed at 0x%02x\n",
+ 8, "read", reg);
+ return 0x00; /* Arbitrary value */
+ }
+
+ return val;
+}
+
+/* Write 8-bit value to register */
+static int emc6w201_write8(struct i2c_client *client, u8 reg, u8 val)
+{
+ int err;
+
+ err = i2c_smbus_write_byte_data(client, reg, val);
+ if (unlikely(err < 0))
+ dev_err(&client->dev, "%d-bit %s failed at 0x%02x\n",
+ 8, "write", reg);
return err;
}
if (time_after(jiffies, data->last_updated + HZ) || !data->valid) {
for (nr = 0; nr < 6; nr++) {
data->in[input][nr] =
- i2c_smbus_read_byte_data(client,
+ emc6w201_read8(client,
EMC6W201_REG_IN(nr));
data->in[min][nr] =
- i2c_smbus_read_byte_data(client,
+ emc6w201_read8(client,
EMC6W201_REG_IN_LOW(nr));
data->in[max][nr] =
- i2c_smbus_read_byte_data(client,
+ emc6w201_read8(client,
EMC6W201_REG_IN_HIGH(nr));
}
for (nr = 0; nr < 6; nr++) {
data->temp[input][nr] =
- i2c_smbus_read_byte_data(client,
+ emc6w201_read8(client,
EMC6W201_REG_TEMP(nr));
data->temp[min][nr] =
- i2c_smbus_read_byte_data(client,
+ emc6w201_read8(client,
EMC6W201_REG_TEMP_LOW(nr));
data->temp[max][nr] =
- i2c_smbus_read_byte_data(client,
+ emc6w201_read8(client,
EMC6W201_REG_TEMP_HIGH(nr));
}
mutex_lock(&data->update_lock);
data->in[sf][nr] = SENSORS_LIMIT(val, 0, 255);
- err = i2c_smbus_write_byte_data(client, reg, data->in[sf][nr]);
+ err = emc6w201_write8(client, reg, data->in[sf][nr]);
mutex_unlock(&data->update_lock);
return err < 0 ? err : count;
mutex_lock(&data->update_lock);
data->temp[sf][nr] = SENSORS_LIMIT(val, -127, 128);
- err = i2c_smbus_write_byte_data(client, reg, data->temp[sf][nr]);
+ err = emc6w201_write8(client, reg, data->temp[sf][nr]);
mutex_unlock(&data->update_lock);
return err < 0 ? err : count;
/* Check configuration */
config = i2c_smbus_read_byte_data(client, EMC6W201_REG_CONFIG);
- if ((config & 0xF4) != 0x04)
+ if (config < 0 || (config & 0xF4) != 0x04)
return -ENODEV;
if (!(config & 0x01)) {
dev_err(&client->dev, "Monitoring not enabled\n");
#define SIO_F71858_ID 0x0507 /* Chipset ID */
#define SIO_F71862_ID 0x0601 /* Chipset ID */
#define SIO_F71869_ID 0x0814 /* Chipset ID */
+#define SIO_F71869A_ID 0x1007 /* Chipset ID */
#define SIO_F71882_ID 0x0541 /* Chipset ID */
#define SIO_F71889_ID 0x0723 /* Chipset ID */
#define SIO_F71889E_ID 0x0909 /* Chipset ID */
module_param(force_id, ushort, 0);
MODULE_PARM_DESC(force_id, "Override the detected device ID");
-enum chips { f71808e, f71808a, f71858fg, f71862fg, f71869, f71882fg, f71889fg,
- f71889ed, f71889a, f8000, f81865f };
+enum chips { f71808e, f71808a, f71858fg, f71862fg, f71869, f71869a, f71882fg,
+ f71889fg, f71889ed, f71889a, f8000, f81865f };
static const char *f71882fg_names[] = {
"f71808e",
"f71858fg",
"f71862fg",
"f71869", /* Both f71869f and f71869e, reg. compatible and same id */
+ "f71869a",
"f71882fg",
"f71889fg", /* f81801u too, same id */
"f71889ed",
[f71858fg] = { 1, 1, 1, 0, 0, 0, 0, 0, 0 },
[f71862fg] = { 1, 1, 1, 1, 1, 1, 1, 1, 1 },
[f71869] = { 1, 1, 1, 1, 1, 1, 1, 1, 1 },
+ [f71869a] = { 1, 1, 1, 1, 1, 1, 1, 1, 1 },
[f71882fg] = { 1, 1, 1, 1, 1, 1, 1, 1, 1 },
[f71889fg] = { 1, 1, 1, 1, 1, 1, 1, 1, 1 },
[f71889ed] = { 1, 1, 1, 1, 1, 1, 1, 1, 1 },
[f71858fg] = 0,
[f71862fg] = 0,
[f71869] = 0,
+ [f71869a] = 0,
[f71882fg] = 1,
[f71889fg] = 1,
[f71889ed] = 1,
[f71858fg] = 0,
[f71862fg] = 1,
[f71869] = 1,
+ [f71869a] = 1,
[f71882fg] = 1,
[f71889fg] = 1,
[f71889ed] = 1,
[f71858fg] = 3,
[f71862fg] = 3,
[f71869] = 3,
+ [f71869a] = 3,
[f71882fg] = 4,
[f71889fg] = 3,
[f71889ed] = 3,
[f71858fg] = 0,
[f71862fg] = 1,
[f71869] = 1,
+ [f71869a] = 1,
[f71882fg] = 1,
[f71889fg] = 1,
[f71889ed] = 1,
[f71858fg] = 3,
[f71862fg] = 3,
[f71869] = 3,
+ [f71869a] = 3,
[f71882fg] = 3,
[f71889fg] = 3,
[f71889ed] = 3,
case f71808e:
case f71808a:
case f71869:
+ case f71869a:
/* These always have signed auto point temps */
data->auto_point_temp_signed = 1;
/* Fall through to select correct fan/pwm reg bank! */
case f71808e:
case f71808a:
case f71869:
+ case f71869a:
case f71889fg:
case f71889ed:
case f71889a:
case SIO_F71869_ID:
sio_data->type = f71869;
break;
+ case SIO_F71869A_ID:
+ sio_data->type = f71869a;
+ break;
case SIO_F71882_ID:
sio_data->type = f71882fg;
break;
}
MODULE_DESCRIPTION("F71882FG Hardware Monitoring Driver");
-MODULE_AUTHOR("Hans Edgington, Hans de Goede (hdegoede@redhat.com)");
+MODULE_AUTHOR("Hans Edgington, Hans de Goede <hdegoede@redhat.com>");
MODULE_LICENSE("GPL");
module_init(f71882fg_init);
{X86_VENDOR_CENTAUR, 0x6, 0x7, ANY, 85}, /* Eden ESP/Ezra */
{X86_VENDOR_CENTAUR, 0x6, 0x8, 0x7, 85}, /* Ezra T */
- {X86_VENDOR_CENTAUR, 0x6, 0x9, 0x7, 85}, /* Nemiah */
+ {X86_VENDOR_CENTAUR, 0x6, 0x9, 0x7, 85}, /* Nehemiah */
{X86_VENDOR_CENTAUR, 0x6, 0x9, ANY, 17}, /* C3-M, Eden-N */
{X86_VENDOR_CENTAUR, 0x6, 0xA, 0x7, 0}, /* No information */
{X86_VENDOR_CENTAUR, 0x6, 0xA, ANY, 13}, /* C7, Esther */
if (info->func[0]
&& pmbus_check_byte_register(client, 0, PMBUS_STATUS_INPUT))
info->func[0] |= PMBUS_HAVE_STATUS_INPUT;
- if (pmbus_check_word_register(client, 0, PMBUS_READ_FAN_SPEED_1)) {
+ if (pmbus_check_byte_register(client, 0, PMBUS_FAN_CONFIG_12) &&
+ pmbus_check_word_register(client, 0, PMBUS_READ_FAN_SPEED_1)) {
info->func[0] |= PMBUS_HAVE_FAN12;
if (pmbus_check_byte_register(client, 0, PMBUS_STATUS_FAN_12))
info->func[0] |= PMBUS_HAVE_STATUS_FAN12;
}
- if (pmbus_check_word_register(client, 0, PMBUS_READ_FAN_SPEED_3)) {
+ if (pmbus_check_byte_register(client, 0, PMBUS_FAN_CONFIG_34) &&
+ pmbus_check_word_register(client, 0, PMBUS_READ_FAN_SPEED_3)) {
info->func[0] |= PMBUS_HAVE_FAN34;
if (pmbus_check_byte_register(client, 0, PMBUS_STATUS_FAN_34))
info->func[0] |= PMBUS_HAVE_STATUS_FAN34;
PMBUS_STATUS_TEMPERATURE))
info->func[0] |= PMBUS_HAVE_STATUS_TEMP;
}
+ if (pmbus_check_word_register(client, 0, PMBUS_READ_TEMPERATURE_2))
+ info->func[0] |= PMBUS_HAVE_TEMP2;
+ if (pmbus_check_word_register(client, 0, PMBUS_READ_TEMPERATURE_3))
+ info->func[0] |= PMBUS_HAVE_TEMP3;
/* Sensors detected on all pages */
for (page = 0; page < info->pages; page++) {
i2c_set_clientdata(client, data);
mutex_init(&data->update_lock);
- /*
- * Bail out if status register or PMBus revision register
- * does not exist.
- */
- if (i2c_smbus_read_byte_data(client, PMBUS_STATUS_BYTE) < 0
- || i2c_smbus_read_byte_data(client, PMBUS_REVISION) < 0) {
- dev_err(&client->dev,
- "Status or revision register not found\n");
+ /* Bail out if PMBus status register does not exist. */
+ if (i2c_smbus_read_byte_data(client, PMBUS_STATUS_BYTE) < 0) {
+ dev_err(&client->dev, "PMBus status register not found\n");
ret = -ENODEV;
goto out_data;
}
}
MODULE_DESCRIPTION("SMSC SCH5627 Hardware Monitoring Driver");
-MODULE_AUTHOR("Hans de Goede (hdegoede@redhat.com)");
+MODULE_AUTHOR("Hans de Goede <hdegoede@redhat.com>");
MODULE_LICENSE("GPL");
module_init(sch5627_init);
if (taos->state != TAOS_STATE_IDLE) {
err = -ENODEV;
- dev_dbg(&serio->dev, "TAOS EVM reset failed (state=%d, "
+ dev_err(&serio->dev, "TAOS EVM reset failed (state=%d, "
"pos=%d)\n", taos->state, taos->pos);
goto exit_close;
}
msecs_to_jiffies(250));
if (taos->state != TAOS_STATE_IDLE) {
err = -ENODEV;
- dev_err(&adapter->dev, "Echo off failed "
+ dev_err(&serio->dev, "TAOS EVM echo off failed "
"(state=%d)\n", taos->state);
goto exit_close;
}
err = i2c_add_adapter(adapter);
if (err)
goto exit_close;
- dev_dbg(&serio->dev, "Connected to TAOS EVM\n");
+ dev_info(&serio->dev, "Connected to TAOS EVM\n");
taos->client = taos_instantiate_device(adapter);
return 0;
serio_set_drvdata(serio, NULL);
kfree(taos);
- dev_dbg(&serio->dev, "Disconnected from TAOS EVM\n");
+ dev_info(&serio->dev, "Disconnected from TAOS EVM\n");
}
static struct serio_device_id taos_serio_ids[] = {
i2c_set_clientdata(client, data);
- /* Read the mux register at addr to verify
- * that the mux is in fact present.
+ /* Write the mux register at addr to verify
+ * that the mux is in fact present. This also
+ * initializes the mux to disconnected state.
*/
- if (i2c_smbus_read_byte(client) < 0) {
+ if (i2c_smbus_write_byte(client, 0) < 0) {
dev_warn(&client->dev, "probe failed\n");
goto exit_free;
}
static char *cm_devnode(struct device *dev, mode_t *mode)
{
- *mode = 0666;
+ if (mode)
+ *mode = 0666;
return kasprintf(GFP_KERNEL, "infiniband/%s", dev_name(dev));
}
static char *uverbs_devnode(struct device *dev, mode_t *mode)
{
- *mode = 0666;
+ if (mode)
+ *mode = 0666;
return kasprintf(GFP_KERNEL, "infiniband/%s", dev_name(dev));
}
&lp5521_led_attribute_group);
}
-static int __init lp5521_init_led(struct lp5521_led *led,
+static int __devinit lp5521_init_led(struct lp5521_led *led,
struct i2c_client *client,
int chan, struct lp5521_platform_data *pdata)
{
return 0;
}
-static int lp5521_probe(struct i2c_client *client,
+static int __devinit lp5521_probe(struct i2c_client *client,
const struct i2c_device_id *id)
{
struct lp5521_chip *chip;
return 0;
}
-static int __init lp5523_init_led(struct lp5523_led *led, struct device *dev,
+static int __devinit lp5523_init_led(struct lp5523_led *led, struct device *dev,
int chan, struct lp5523_platform_data *pdata)
{
char name[32];
static struct i2c_driver lp5523_driver;
-static int lp5523_probe(struct i2c_client *client,
+static int __devinit lp5523_probe(struct i2c_client *client,
const struct i2c_device_id *id)
{
struct lp5523_chip *chip;
list_for_each_entry(rdev, &mddev->disks, same_set) {
if (rdev->raid_disk >= 0 &&
!test_bit(In_sync, &rdev->flags) &&
+ !test_bit(Faulty, &rdev->flags) &&
!test_bit(Blocked, &rdev->flags))
spares++;
if (rdev->raid_disk < 0
static inline bool needs_unaligned_copy(const void *ptr)
{
-#ifdef HAVE_EFFICIENT_UNALIGNED_ACCESS
+#ifdef CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS
return false;
#else
return ((ptr - NULL) & 3) != 0;
return IOC4_VARIANT_PCI_RT;
}
-static void __devinit
+static void
ioc4_load_modules(struct work_struct *work)
{
request_module("sgiioc4");
static enum cname cpoint = CN_INVALID;
static enum ctype cptype = CT_NONE;
static int count = DEFAULT_COUNT;
+static DEFINE_SPINLOCK(count_lock);
module_param(recur_count, int, 0644);
MODULE_PARM_DESC(recur_count, " Recursion level for the stack overflow test, "\
static int lkdtm_parse_commandline(void)
{
int i;
+ unsigned long flags;
if (cpoint_count < 1 || recur_count < 1)
return -EINVAL;
+ spin_lock_irqsave(&count_lock, flags);
count = cpoint_count;
+ spin_unlock_irqrestore(&count_lock, flags);
/* No special parameters */
if (!cpoint_type && !cpoint_name)
static void lkdtm_handler(void)
{
+ unsigned long flags;
+
+ spin_lock_irqsave(&count_lock, flags);
count--;
printk(KERN_INFO "lkdtm: Crash point %s of type %s hit, trigger in %d rounds\n",
cp_name_to_str(cpoint), cp_type_to_str(cptype), count);
lkdtm_do_action(cptype);
count = cpoint_count;
}
+ spin_unlock_irqrestore(&count_lock, flags);
}
static int lkdtm_register_cpoint(enum cname which)
* a master, channel ID address
* used to write to PTI HW.
*
- * @mc: master, channel apeture ID address to be released.
+ * @mc: master, channel apeture ID address to be released. This
+ * will de-allocate the structure via kfree().
*/
void pti_release_masterchannel(struct pti_masterchannel *mc)
{
else
pti_tty_data->mc = pti_request_masterchannel(2);
- if (pti_tty_data->mc == NULL)
+ if (pti_tty_data->mc == NULL) {
+ kfree(pti_tty_data);
return -ENXIO;
+ }
tty->driver_data = pti_tty_data;
}
if (pti_tty_data == NULL)
return;
pti_release_masterchannel(pti_tty_data->mc);
- kfree(tty->driver_data);
+ kfree(pti_tty_data);
tty->driver_data = NULL;
}
static int pti_char_release(struct inode *inode, struct file *filp)
{
pti_release_masterchannel(filp->private_data);
- kfree(filp->private_data);
+ filp->private_data = NULL;
return 0;
}
pr_debug("%s: %d ", __func__, proto->chnl_id);
st_kim_ref(&st_gdata, 0);
- if (proto->chnl_id >= ST_MAX_CHANNELS) {
+ if (!st_gdata || proto->chnl_id >= ST_MAX_CHANNELS) {
pr_err(" chnl_id %d not supported", proto->chnl_id);
return -EPROTONOSUPPORT;
}
pr_err("invalid action after change remote baud command");
} else {
*ptr = *ptr + sizeof(struct bts_action) +
- ((struct bts_action *)nxt_action)->size;
+ ((struct bts_action *)cur_action)->size;
*len = *len - (sizeof(struct bts_action) +
- ((struct bts_action *)nxt_action)->size);
+ ((struct bts_action *)cur_action)->size);
/* warn user on not commenting these in firmware */
pr_warn("skipping the wait event of change remote baud");
}
struct kim_data_s *kim_gdata;
/* get kim_gdata reference from platform device */
pdev = st_get_plat_device(id);
+ if (!pdev) {
+ *core_data = NULL;
+ return;
+ }
kim_gdata = dev_get_drvdata(&pdev->dev);
*core_data = kim_gdata->core_data;
}
INIT_LIST_HEAD(&md->part);
md->usage = 1;
- ret = mmc_init_queue(&md->queue, card, &md->lock);
+ ret = mmc_init_queue(&md->queue, card, &md->lock, subname);
if (ret)
goto err_putdisk;
struct mmc_blk_data *md = mmc_get_drvdata(card);
mmc_blk_remove_parts(card, md);
+ mmc_claim_host(card->host);
+ mmc_blk_part_switch(card, md);
+ mmc_release_host(card->host);
mmc_blk_remove_req(md);
mmc_set_drvdata(card, NULL);
}
* @mq: mmc queue
* @card: mmc card to attach this queue
* @lock: queue lock
+ * @subname: partition subname
*
* Initialise a MMC card request queue.
*/
-int mmc_init_queue(struct mmc_queue *mq, struct mmc_card *card, spinlock_t *lock)
+int mmc_init_queue(struct mmc_queue *mq, struct mmc_card *card,
+ spinlock_t *lock, const char *subname)
{
struct mmc_host *host = card->host;
u64 limit = BLK_BOUNCE_HIGH;
mq->queue->limits.max_discard_sectors = UINT_MAX;
if (card->erased_byte == 0)
mq->queue->limits.discard_zeroes_data = 1;
- if (!mmc_can_trim(card) && is_power_of_2(card->erase_size)) {
- mq->queue->limits.discard_granularity =
- card->erase_size << 9;
- mq->queue->limits.discard_alignment =
- card->erase_size << 9;
- }
+ mq->queue->limits.discard_granularity = card->pref_erase << 9;
if (mmc_can_secure_erase_trim(card))
queue_flag_set_unlocked(QUEUE_FLAG_SECDISCARD,
mq->queue);
sema_init(&mq->thread_sem, 1);
- mq->thread = kthread_run(mmc_queue_thread, mq, "mmcqd/%d",
- host->index);
+ mq->thread = kthread_run(mmc_queue_thread, mq, "mmcqd/%d%s",
+ host->index, subname ? subname : "");
if (IS_ERR(mq->thread)) {
ret = PTR_ERR(mq->thread);
unsigned int bounce_sg_len;
};
-extern int mmc_init_queue(struct mmc_queue *, struct mmc_card *, spinlock_t *);
+extern int mmc_init_queue(struct mmc_queue *, struct mmc_card *, spinlock_t *,
+ const char *);
extern void mmc_cleanup_queue(struct mmc_queue *);
extern void mmc_queue_suspend(struct mmc_queue *);
extern void mmc_queue_resume(struct mmc_queue *);
*/
timeout_clks <<= 1;
timeout_us += (timeout_clks * 1000) /
- (card->host->ios.clock / 1000);
+ (mmc_host_clk_rate(card->host) / 1000);
erase_timeout = timeout_us / 1000;
static int mmc_sdio_power_restore(struct mmc_host *host)
{
int ret;
+ u32 ocr;
BUG_ON(!host);
BUG_ON(!host->card);
mmc_claim_host(host);
+
+ /*
+ * Reset the card by performing the same steps that are taken by
+ * mmc_rescan_try_freq() and mmc_attach_sdio() during a "normal" probe.
+ *
+ * sdio_reset() is technically not needed. Having just powered up the
+ * hardware, it should already be in reset state. However, some
+ * platforms (such as SD8686 on OLPC) do not instantly cut power,
+ * meaning that a reset is required when restoring power soon after
+ * powering off. It is harmless in other cases.
+ *
+ * The CMD5 reset (mmc_send_io_op_cond()), according to the SDIO spec,
+ * is not necessary for non-removable cards. However, it is required
+ * for OLPC SD8686 (which expects a [CMD5,5,3,7] init sequence), and
+ * harmless in other situations.
+ *
+ * With these steps taken, mmc_select_voltage() is also required to
+ * restore the correct voltage setting of the card.
+ */
+ sdio_reset(host);
+ mmc_go_idle(host);
+ mmc_send_if_cond(host, host->ocr_avail);
+
+ ret = mmc_send_io_op_cond(host, 0, &ocr);
+ if (ret)
+ goto out;
+
+ if (host->ocr_avail_sdio)
+ host->ocr_avail = host->ocr_avail_sdio;
+
+ host->ocr = mmc_select_voltage(host, ocr & ~0x7F);
+ if (!host->ocr) {
+ ret = -EINVAL;
+ goto out;
+ }
+
ret = mmc_sdio_init_card(host, host->ocr, host->card,
mmc_card_keep_power(host));
if (!ret && host->sdio_irqs)
mmc_signal_sdio_irq(host);
+
+out:
mmc_release_host(host);
return ret;
/* Then undo the runtime PM settings in sdio_bus_probe() */
if (func->card->host->caps & MMC_CAP_POWER_OFF_CARD)
- pm_runtime_put_noidle(dev);
+ pm_runtime_put_sync(dev);
out:
return ret;
#include <linux/mmc/core.h>
#include <linux/mmc/host.h>
+/* For archs that don't support NO_IRQ (such as mips), provide a dummy value */
+#ifndef NO_IRQ
+#define NO_IRQ 0
+#endif
+
MODULE_LICENSE("GPL");
enum {
return -EINVAL;
}
}
- mmc_slot(host).ocr_mask = mmc_regulator_get_ocrmask(reg);
/* Allow an aux regulator */
reg = regulator_get(host->dev, "vmmc_aux");
spin_unlock(&host->irq_lock);
if (host->use_dma && dma_ch != -1) {
- dma_unmap_sg(mmc_dev(host->mmc), host->data->sg, host->dma_len,
+ dma_unmap_sg(mmc_dev(host->mmc), host->data->sg,
+ host->data->sg_len,
omap_hsmmc_get_dma_dir(host, host->data));
omap_free_dma(dma_ch);
}
return;
}
- dma_unmap_sg(mmc_dev(host->mmc), data->sg, host->dma_len,
+ dma_unmap_sg(mmc_dev(host->mmc), data->sg, data->sg_len,
omap_hsmmc_get_dma_dir(host, data));
req_in_progress = host->req_in_progress;
mmc_data->ocr_mask = p->tmio_ocr_mask;
mmc_data->capabilities |= p->tmio_caps;
- if (p->dma_slave_tx >= 0 && p->dma_slave_rx >= 0) {
+ if (p->dma_slave_tx > 0 && p->dma_slave_rx > 0) {
priv->param_tx.slave_id = p->dma_slave_tx;
priv->param_rx.slave_id = p->dma_slave_rx;
priv->dma_priv.chan_priv_tx = &priv->param_tx;
p->pdata = NULL;
+ tmio_mmc_host_remove(host);
+
for (i = 0; i < 3; i++) {
irq = platform_get_irq(pdev, i);
if (irq >= 0)
free_irq(irq, host);
}
- tmio_mmc_host_remove(host);
clk_disable(priv->clk);
clk_put(priv->clk);
kfree(priv);
struct tmio_mmc_host *host = mmc_priv(mmc);
struct tmio_mmc_data *pdata = host->pdata;
- return ((pdata->flags & TMIO_MMC_WRPROTECT_DISABLE) ||
- !(sd_ctrl_read32(host, CTL_STATUS) & TMIO_STAT_WRPROTECT));
+ return !((pdata->flags & TMIO_MMC_WRPROTECT_DISABLE) ||
+ (sd_ctrl_read32(host, CTL_STATUS) & TMIO_STAT_WRPROTECT));
}
static int tmio_mmc_get_cd(struct mmc_host *mmc)
static int vub300_probe(struct usb_interface *interface,
const struct usb_device_id *id)
{ /* NOT irq */
- struct vub300_mmc_host *vub300 = NULL;
+ struct vub300_mmc_host *vub300;
struct usb_host_interface *iface_desc;
struct usb_device *udev = usb_get_dev(interface_to_usbdev(interface));
int i;
command_out_urb = usb_alloc_urb(0, GFP_KERNEL);
if (!command_out_urb) {
retval = -ENOMEM;
- dev_err(&vub300->udev->dev,
- "not enough memory for the command_out_urb\n");
+ dev_err(&udev->dev, "not enough memory for command_out_urb\n");
goto error0;
}
command_res_urb = usb_alloc_urb(0, GFP_KERNEL);
if (!command_res_urb) {
retval = -ENOMEM;
- dev_err(&vub300->udev->dev,
- "not enough memory for the command_res_urb\n");
+ dev_err(&udev->dev, "not enough memory for command_res_urb\n");
goto error1;
}
/* this also allocates memory for our VUB300 mmc host device */
mmc = mmc_alloc_host(sizeof(struct vub300_mmc_host), &udev->dev);
if (!mmc) {
retval = -ENOMEM;
- dev_err(&vub300->udev->dev,
- "not enough memory for the mmc_host\n");
+ dev_err(&udev->dev, "not enough memory for the mmc_host\n");
goto error4;
}
/* MMC core transfer sizes tunable parameters */
(FIR_OP_UA << FIR_OP1_SHIFT) |
(FIR_OP_RBW << FIR_OP2_SHIFT));
out_be32(&lbc->fcr, NAND_CMD_READID << FCR_CMD0_SHIFT);
- /* 5 bytes for manuf, device and exts */
- out_be32(&lbc->fbcr, 5);
- elbc_fcm_ctrl->read_bytes = 5;
+ /* nand_get_flash_type() reads 8 bytes of entire ID string */
+ out_be32(&lbc->fbcr, 8);
+ elbc_fcm_ctrl->read_bytes = 8;
elbc_fcm_ctrl->use_mdr = 1;
elbc_fcm_ctrl->mdr = 0;
config NETCONSOLE_DYNAMIC
bool "Dynamic reconfiguration of logging targets"
- depends on NETCONSOLE && SYSFS && CONFIGFS_FS
+ depends on NETCONSOLE && SYSFS && CONFIGFS_FS && \
+ !(NETCONSOLE=y && CONFIGFS_FS=m)
help
This option enables the ability to dynamically reconfigure target
parameters (interface, IP addresses, port numbers, MAC addresses)
#include <linux/zlib.h>
#include <linux/io.h>
#include <linux/stringify.h>
+#include <linux/vmalloc.h>
#define BNX2X_MAIN
#include "bnx2x.h"
if (bp->strm == NULL)
goto gunzip_nomem2;
- bp->strm->workspace = kmalloc(zlib_inflate_workspacesize(),
- GFP_KERNEL);
+ bp->strm->workspace = vmalloc(zlib_inflate_workspacesize());
if (bp->strm->workspace == NULL)
goto gunzip_nomem3;
static void bnx2x_gunzip_end(struct bnx2x *bp)
{
if (bp->strm) {
- kfree(bp->strm->workspace);
+ vfree(bp->strm->workspace);
kfree(bp->strm);
bp->strm = NULL;
}
config CAN_DEV
tristate "Platform CAN drivers with Netlink support"
depends on CAN
- default Y
+ default y
---help---
Enables the common framework for platform CAN drivers with Netlink
support. This is the standard library for CAN drivers.
config CAN_CALC_BITTIMING
bool "CAN bit-timing calculation"
depends on CAN_DEV
- default Y
+ default y
---help---
If enabled, CAN bit-timing parameters will be calculated for the
bit-rate specified via Netlink argument "bitrate" when the device
skb->ip_summed = CHECKSUM_UNNECESSARY;
} else
skb_checksum_none_assert(skb);
- skb_record_rx_queue(skb, qs - &adap->sge.qs[0]);
+ skb_record_rx_queue(skb, qs - &adap->sge.qs[pi->first_qset]);
if (unlikely(p->vlan_valid)) {
struct vlan_group *grp = pi->vlan_grp;
if (!complete)
return;
- skb_record_rx_queue(skb, qs - &adap->sge.qs[0]);
+ skb_record_rx_queue(skb, qs - &adap->sge.qs[pi->first_qset]);
if (unlikely(cpl->vlan_valid)) {
struct vlan_group *grp = pi->vlan_grp;
if (state) {
zlib_inflateEnd(&state->strm);
- kfree(state->strm.workspace);
+ vfree(state->strm.workspace);
kfree(state);
}
}
state->w_size = w_size;
state->strm.next_out = NULL;
- state->strm.workspace = kmalloc(zlib_inflate_workspacesize(),
- GFP_KERNEL|__GFP_REPEAT);
+ state->strm.workspace = vmalloc(zlib_inflate_workspacesize());
if (state->strm.workspace == NULL)
goto out_free;
msleep(2);
for (i = 0; i < 5; i++) {
udelay(100);
- if (!(RTL_R32(ERIDR) & ERIAR_FLAG))
+ if (!(RTL_R32(ERIAR) & ERIAR_FLAG))
break;
}
static void rionet_remove(struct rio_dev *rdev)
{
- struct net_device *ndev = NULL;
+ struct net_device *ndev = rio_get_drvdata(rdev);
struct rionet_peer *peer, *tmp;
free_pages((unsigned long)rionet_active, rdev->net->hport->sys_size ?
.ndo_set_mac_address = eth_mac_addr,
};
-static int rionet_setup_netdev(struct rio_mport *mport)
+static int rionet_setup_netdev(struct rio_mport *mport, struct net_device *ndev)
{
int rc = 0;
- struct net_device *ndev = NULL;
struct rionet_private *rnet;
u16 device_id;
- /* Allocate our net_device structure */
- ndev = alloc_etherdev(sizeof(struct rionet_private));
- if (ndev == NULL) {
- printk(KERN_INFO "%s: could not allocate ethernet device.\n",
- DRV_NAME);
- rc = -ENOMEM;
- goto out;
- }
-
rionet_active = (struct rio_dev **)__get_free_pages(GFP_KERNEL,
mport->sys_size ? __fls(sizeof(void *)) + 4 : 0);
if (!rionet_active) {
int rc = -ENODEV;
u32 lpef, lsrc_ops, ldst_ops;
struct rionet_peer *peer;
+ struct net_device *ndev = NULL;
/* If local device is not rionet capable, give up quickly */
if (!rionet_capable)
goto out;
+ /* Allocate our net_device structure */
+ ndev = alloc_etherdev(sizeof(struct rionet_private));
+ if (ndev == NULL) {
+ printk(KERN_INFO "%s: could not allocate ethernet device.\n",
+ DRV_NAME);
+ rc = -ENOMEM;
+ goto out;
+ }
+
/*
* First time through, make sure local device is rionet
* capable, setup netdev, and set flags so this is skipped
goto out;
}
- rc = rionet_setup_netdev(rdev->net->hport);
+ rc = rionet_setup_netdev(rdev->net->hport, ndev);
rionet_check = 1;
}
list_add_tail(&peer->node, &rionet_peers);
}
+ rio_set_drvdata(rdev, ndev);
+
out:
return rc;
}
static int
kalmia_init_and_get_ethernet_addr(struct usbnet *dev, u8 *ethernet_addr)
{
- char init_msg_1[] =
+ const static char init_msg_1[] =
{ 0x57, 0x50, 0x04, 0x00, 0x00, 0x00, 0x00, 0x20, 0x00, 0x00,
0x00, 0x00 };
- char init_msg_2[] =
+ const static char init_msg_2[] =
{ 0x57, 0x50, 0x04, 0x00, 0x00, 0x00, 0x00, 0x02, 0x00, 0xf4,
0x00, 0x00 };
- char receive_buf[28];
+ const static int buflen = 28;
+ char *usb_buf;
int status;
- status = kalmia_send_init_packet(dev, init_msg_1, sizeof(init_msg_1)
- / sizeof(init_msg_1[0]), receive_buf, 24);
+ usb_buf = kmalloc(buflen, GFP_DMA | GFP_KERNEL);
+ if (!usb_buf)
+ return -ENOMEM;
+
+ memcpy(usb_buf, init_msg_1, 12);
+ status = kalmia_send_init_packet(dev, usb_buf, sizeof(init_msg_1)
+ / sizeof(init_msg_1[0]), usb_buf, 24);
if (status != 0)
return status;
- status = kalmia_send_init_packet(dev, init_msg_2, sizeof(init_msg_2)
- / sizeof(init_msg_2[0]), receive_buf, 28);
+ memcpy(usb_buf, init_msg_2, 12);
+ status = kalmia_send_init_packet(dev, usb_buf, sizeof(init_msg_2)
+ / sizeof(init_msg_2[0]), usb_buf, 28);
if (status != 0)
return status;
- memcpy(ethernet_addr, receive_buf + 10, ETH_ALEN);
+ memcpy(ethernet_addr, usb_buf + 10, ETH_ALEN);
+ kfree(usb_buf);
return status;
}
static int
kalmia_bind(struct usbnet *dev, struct usb_interface *intf)
{
- u8 status;
+ int status;
u8 ethernet_addr[ETH_ALEN];
/* Don't bind to AT command interface */
dev_kfree_skb_any(skb);
skb = skb2;
- done: header_start = skb_push(skb, KALMIA_HEADER_LENGTH);
+done:
+ header_start = skb_push(skb, KALMIA_HEADER_LENGTH);
ether_type_1 = header_start[KALMIA_HEADER_LENGTH + 12];
ether_type_2 = header_start[KALMIA_HEADER_LENGTH + 13];
header_start[0] = 0x57;
header_start[1] = 0x44;
content_len = skb->len - KALMIA_HEADER_LENGTH;
- header_start[2] = (content_len & 0xff); /* low byte */
- header_start[3] = (content_len >> 8); /* high byte */
+ put_unaligned_le16(content_len, &header_start[2]);
header_start[4] = ether_type_1;
header_start[5] = ether_type_2;
* Our task here is to strip off framing, leaving skb with one
* data frame for the usbnet framework code to process.
*/
- const u8 HEADER_END_OF_USB_PACKET[] =
+ const static u8 HEADER_END_OF_USB_PACKET[] =
{ 0x57, 0x5a, 0x00, 0x00, 0x08, 0x00 };
- const u8 EXPECTED_UNKNOWN_HEADER_1[] =
+ const static u8 EXPECTED_UNKNOWN_HEADER_1[] =
{ 0x57, 0x43, 0x1e, 0x00, 0x15, 0x02 };
- const u8 EXPECTED_UNKNOWN_HEADER_2[] =
+ const static u8 EXPECTED_UNKNOWN_HEADER_2[] =
{ 0x57, 0x50, 0x0e, 0x00, 0x00, 0x00 };
- u8 i = 0;
+ int i = 0;
/* incomplete header? */
if (skb->len < KALMIA_HEADER_LENGTH)
/* subtract start header and end header */
usb_packet_length = skb->len - (2 * KALMIA_HEADER_LENGTH);
- ether_packet_length = header_start[2] + (header_start[3] << 8);
+ ether_packet_length = get_unaligned_le16(&header_start[2]);
skb_pull(skb, KALMIA_HEADER_LENGTH);
/* Some small packets misses end marker */
ZAURUS_MASTER_INTERFACE,
.driver_info = ZAURUS_PXA_INFO,
},
-
-
-/* At least some of the newest PXA units have very different lies about
- * their standards support: they claim to be cell phones offering
- * direct access to their radios! (No, they don't conform to CDC MDLM.)
- */
{
- USB_INTERFACE_INFO(USB_CLASS_COMM, USB_CDC_SUBCLASS_MDLM,
- USB_CDC_PROTO_NONE),
- .driver_info = (unsigned long) &bogus_mdlm_info,
-}, {
/* Motorola MOTOMAGX phones */
USB_DEVICE_AND_INTERFACE_INFO(0x22b8, 0x6425, USB_CLASS_COMM,
USB_CDC_SUBCLASS_MDLM, USB_CDC_PROTO_NONE),
pci_read_config_byte(pdev, 0x8, &revisionid);
pci_read_config_word(pdev, 0x3C, &irqline);
+ /* PCI ID 0x10ec:0x8192 occurs for both RTL8192E, which uses
+ * r8192e_pci, and RTL8192SE, which uses this driver. If the
+ * revision ID is RTL_PCI_REVISION_ID_8192PCIE (0x01), then
+ * the correct driver is r8192e_pci, thus this routine should
+ * return false.
+ */
+ if (deviceid == RTL_PCI_8192SE_DID &&
+ revisionid == RTL_PCI_REVISION_ID_8192PCIE)
+ return false;
+
if (deviceid == RTL_PCI_8192_DID ||
deviceid == RTL_PCI_0044_DID ||
deviceid == RTL_PCI_0047_DID ||
pci_write_config_byte(pdev, 0x04, 0x07);
/* find adapter */
- _rtl_pci_find_adapter(pdev, hw);
+ if (!_rtl_pci_find_adapter(pdev, hw))
+ goto fail3;
/* Init IO handler */
_rtl_pci_io_handler_init(&pdev->dev, hw);
static int rtl92cu_init_sw_vars(struct ieee80211_hw *hw)
{
struct rtl_priv *rtlpriv = rtl_priv(hw);
+ const struct firmware *firmware;
+ int err;
rtlpriv->dm.dm_initialgain_enable = 1;
rtlpriv->dm.dm_flag = 0;
("Can't alloc buffer for fw.\n"));
return 1;
}
+ /* request fw */
+ err = request_firmware(&firmware, rtlpriv->cfg->fw_name,
+ rtlpriv->io.dev);
+ if (err) {
+ RT_TRACE(rtlpriv, COMP_ERR, DBG_EMERG,
+ ("Failed to request firmware!\n"));
+ return 1;
+ }
+ if (firmware->size > 0x4000) {
+ RT_TRACE(rtlpriv, COMP_ERR, DBG_EMERG,
+ ("Firmware is too big!\n"));
+ release_firmware(firmware);
+ return 1;
+ }
+ memcpy(rtlpriv->rtlhal.pfirmware, firmware->data, firmware->size);
+ rtlpriv->rtlhal.fwsize = firmware->size;
+ release_firmware(firmware);
+
return 0;
}
* @dev: the PCI device
* @decode: true = enable decoding, false = disable decoding
* @command_bits: PCI_COMMAND_IO and/or PCI_COMMAND_MEMORY
- * @change_bridge_flags: traverse ancestors and change bridges
+ * @flags: traverse ancestors and change bridges
* CHANGE_BRIDGE_ONLY / CHANGE_BRIDGE
*/
int pci_set_vga_state(struct pci_dev *dev, bool decode,
res->flags |= pci_calc_resource_flags(l) | IORESOURCE_SIZEALIGN;
if (type == pci_bar_io) {
l &= PCI_BASE_ADDRESS_IO_MASK;
- mask = PCI_BASE_ADDRESS_IO_MASK & IO_SPACE_LIMIT;
+ mask = PCI_BASE_ADDRESS_IO_MASK & (u32) IO_SPACE_LIMIT;
} else {
l &= PCI_BASE_ADDRESS_MEM_MASK;
mask = (u32)PCI_BASE_ADDRESS_MEM_MASK;
}
DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_RICOH, PCI_DEVICE_ID_RICOH_R5C832, ricoh_mmc_fixup_r5c832);
DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_RICOH, PCI_DEVICE_ID_RICOH_R5C832, ricoh_mmc_fixup_r5c832);
+DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_RICOH, PCI_DEVICE_ID_RICOH_R5CE823, ricoh_mmc_fixup_r5c832);
+DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_RICOH, PCI_DEVICE_ID_RICOH_R5CE823, ricoh_mmc_fixup_r5c832);
#endif /*CONFIG_MMC_RICOH_MMC*/
#if defined(CONFIG_DMAR) || defined(CONFIG_INTR_REMAP)
{ "ds1340", ds_1340 },
{ "ds3231", ds_3231 },
{ "m41t00", m41t00 },
+ { "pt7c4338", ds_1307 },
{ "rx8025", rx_8025 },
{ }
};
void __iomem *regbase;
struct resource *res;
int irq_alarm;
- int irq_hz;
struct rtc_device *rtc;
spinlock_t lock; /* Protects this structure */
};
if (isr & 1)
events |= RTC_AF | RTC_IRQF;
- /* Only second/minute interrupts are supported */
- if (isr & 2)
- events |= RTC_UF | RTC_IRQF;
-
rtc_update_irq(vt8500_rtc->rtc, 1, events);
return IRQ_HANDLED;
return 0;
}
-static int vt8500_update_irq_enable(struct device *dev, unsigned int enabled)
-{
- struct vt8500_rtc *vt8500_rtc = dev_get_drvdata(dev);
- unsigned long tmp = readl(vt8500_rtc->regbase + VT8500_RTC_CR);
-
- if (enabled)
- tmp |= VT8500_RTC_CR_SM_SEC | VT8500_RTC_CR_SM_ENABLE;
- else
- tmp &= ~VT8500_RTC_CR_SM_ENABLE;
-
- writel(tmp, vt8500_rtc->regbase + VT8500_RTC_CR);
- return 0;
-}
-
static const struct rtc_class_ops vt8500_rtc_ops = {
.read_time = vt8500_rtc_read_time,
.set_time = vt8500_rtc_set_time,
.read_alarm = vt8500_rtc_read_alarm,
.set_alarm = vt8500_rtc_set_alarm,
.alarm_irq_enable = vt8500_alarm_irq_enable,
- .update_irq_enable = vt8500_update_irq_enable,
};
static int __devinit vt8500_rtc_probe(struct platform_device *pdev)
goto err_free;
}
- vt8500_rtc->irq_hz = platform_get_irq(pdev, 1);
- if (vt8500_rtc->irq_hz < 0) {
- dev_err(&pdev->dev, "No 1Hz IRQ resource defined\n");
- ret = -ENXIO;
- goto err_free;
- }
-
vt8500_rtc->res = request_mem_region(vt8500_rtc->res->start,
resource_size(vt8500_rtc->res),
"vt8500-rtc");
goto err_release;
}
- /* Enable the second/minute interrupt generation and enable RTC */
- writel(VT8500_RTC_CR_ENABLE | VT8500_RTC_CR_24H
- | VT8500_RTC_CR_SM_ENABLE | VT8500_RTC_CR_SM_SEC,
+ /* Enable RTC and set it to 24-hour mode */
+ writel(VT8500_RTC_CR_ENABLE | VT8500_RTC_CR_24H,
vt8500_rtc->regbase + VT8500_RTC_CR);
vt8500_rtc->rtc = rtc_device_register("vt8500-rtc", &pdev->dev,
goto err_unmap;
}
- ret = request_irq(vt8500_rtc->irq_hz, vt8500_rtc_irq, 0,
- "rtc 1Hz", vt8500_rtc);
- if (ret < 0) {
- dev_err(&pdev->dev, "can't get irq %i, err %d\n",
- vt8500_rtc->irq_hz, ret);
- goto err_unreg;
- }
-
ret = request_irq(vt8500_rtc->irq_alarm, vt8500_rtc_irq, 0,
"rtc alarm", vt8500_rtc);
if (ret < 0) {
dev_err(&pdev->dev, "can't get irq %i, err %d\n",
vt8500_rtc->irq_alarm, ret);
- goto err_free_hz;
+ goto err_unreg;
}
return 0;
-err_free_hz:
- free_irq(vt8500_rtc->irq_hz, vt8500_rtc);
err_unreg:
rtc_device_unregister(vt8500_rtc->rtc);
err_unmap:
struct vt8500_rtc *vt8500_rtc = platform_get_drvdata(pdev);
free_irq(vt8500_rtc->irq_alarm, vt8500_rtc);
- free_irq(vt8500_rtc->irq_hz, vt8500_rtc);
rtc_device_unregister(vt8500_rtc->rtc);
default n
depends on PCI
depends on WLAN && MAC80211
+ depends on X86 || MIPS
select BRCMUTIL
select FW_LOADER
select CRC_CCITT
default n
depends on MMC
depends on WLAN && CFG80211
+ depends on X86 || MIPS
select BRCMUTIL
select FW_LOADER
select WIRELESS_EXT
tristate "Data acquisition support (comedi)"
default N
depends on m
+ depends on BROKEN || FRV || M32R || MN10300 || SUPERH || TILE || X86
---help---
Enable support a wide range of data acquisition devices
for Linux.
config COMEDI_PCL812
tristate "Advantech PCL-812/813 and ADlink ACL-8112/8113/8113/8216"
+ depends on VIRT_TO_BUS
default N
---help---
Enable support for Advantech PCL-812/PG, PCL-813/B, ADLink
config COMEDI_PCL816
tristate "Advantech PCL-814 and PCL-816 ISA card support"
+ depends on VIRT_TO_BUS
default N
---help---
Enable support for Advantech PCL-814 and PCL-816 ISA cards
config COMEDI_PCL818
tristate "Advantech PCL-718 and PCL-818 ISA card support"
+ depends on VIRT_TO_BUS
default N
---help---
Enable support for Advantech PCL-818 ISA cards
config COMEDI_DAS1800
tristate "DAS1800 and compatible ISA card support"
+ depends on VIRT_TO_BUS
select COMEDI_FC
default N
---help---
config COMEDI_DT282X
tristate "Data Translation DT2821 series and DT-EZ ISA card support"
select COMEDI_FC
+ depends on VIRT_TO_BUS
default N
---help---
Enable support for Data Translation DT2821 series including DT-EZ
config COMEDI_NI_AT_A2150
tristate "NI AT-A2150 ISA card support"
depends on COMEDI_NI_COMMON
+ depends on VIRT_TO_BUS
default N
---help---
Enable support for National Instruments AT-A2150 cards
config COMEDI_ADDI_APCI_035
tristate "ADDI-DATA APCI_035 support"
+ depends on VIRT_TO_BUS
default N
---help---
Enable support for ADDI-DATA APCI_035 cards
config COMEDI_ADDI_APCI_1032
tristate "ADDI-DATA APCI_1032 support"
+ depends on VIRT_TO_BUS
default N
---help---
Enable support for ADDI-DATA APCI_1032 cards
config COMEDI_ADDI_APCI_1500
tristate "ADDI-DATA APCI_1500 support"
+ depends on VIRT_TO_BUS
default N
---help---
Enable support for ADDI-DATA APCI_1500 cards
config COMEDI_ADDI_APCI_1516
tristate "ADDI-DATA APCI_1516 support"
+ depends on VIRT_TO_BUS
default N
---help---
Enable support for ADDI-DATA APCI_1516 cards
config COMEDI_ADDI_APCI_1564
tristate "ADDI-DATA APCI_1564 support"
+ depends on VIRT_TO_BUS
default N
---help---
Enable support for ADDI-DATA APCI_1564 cards
config COMEDI_ADDI_APCI_16XX
tristate "ADDI-DATA APCI_16xx support"
+ depends on VIRT_TO_BUS
default N
---help---
Enable support for ADDI-DATA APCI_16xx cards
config COMEDI_ADDI_APCI_2016
tristate "ADDI-DATA APCI_2016 support"
+ depends on VIRT_TO_BUS
default N
---help---
Enable support for ADDI-DATA APCI_2016 cards
config COMEDI_ADDI_APCI_2032
tristate "ADDI-DATA APCI_2032 support"
+ depends on VIRT_TO_BUS
default N
---help---
Enable support for ADDI-DATA APCI_2032 cards
config COMEDI_ADDI_APCI_2200
tristate "ADDI-DATA APCI_2200 support"
+ depends on VIRT_TO_BUS
default N
---help---
Enable support for ADDI-DATA APCI_2200 cards
config COMEDI_ADDI_APCI_3001
tristate "ADDI-DATA APCI_3001 support"
+ depends on VIRT_TO_BUS
select COMEDI_FC
default N
---help---
config COMEDI_ADDI_APCI_3120
tristate "ADDI-DATA APCI_3520 support"
+ depends on VIRT_TO_BUS
select COMEDI_FC
default N
---help---
config COMEDI_ADDI_APCI_3501
tristate "ADDI-DATA APCI_3501 support"
+ depends on VIRT_TO_BUS
default N
---help---
Enable support for ADDI-DATA APCI_3501 cards
config COMEDI_ADDI_APCI_3XXX
tristate "ADDI-DATA APCI_3xxx support"
+ depends on VIRT_TO_BUS
default N
---help---
Enable support for ADDI-DATA APCI_3xxx cards
config COMEDI_ADL_PCI9118
tristate "ADLink PCI-9118DG, PCI-9118HG, PCI-9118HR support"
select COMEDI_FC
+ depends on VIRT_TO_BUS
default N
---help---
Enable support for ADlink PCI-9118DG, PCI-9118HG, PCI-9118HR cards
depends on COMEDI_MITE
select COMEDI_8255
select COMEDI_FC
+ depends on VIRT_TO_BUS
default N
---help---
Enable support for National Instruments Lab-PC and compatibles
menuconfig IIO
tristate "Industrial I/O support"
- depends on !S390
+ depends on GENERIC_HARDIRQS
help
The industrial I/O subsystem provides a unified framework for
drivers for many different types of embedded sensors using a
int adis16204_set_irq(struct iio_dev *indio_dev, bool enable);
-#ifdef CONFIG_IIO_RING_BUFFER
enum adis16204_scan {
ADIS16204_SCAN_SUPPLY,
ADIS16204_SCAN_ACC_X,
ADIS16204_SCAN_TEMP,
};
+#ifdef CONFIG_IIO_RING_BUFFER
void adis16204_remove_trigger(struct iio_dev *indio_dev);
int adis16204_probe_trigger(struct iio_dev *indio_dev);
int adis16209_set_irq(struct iio_dev *indio_dev, bool enable);
-#ifdef CONFIG_IIO_RING_BUFFER
-
#define ADIS16209_SCAN_SUPPLY 0
#define ADIS16209_SCAN_ACC_X 1
#define ADIS16209_SCAN_ACC_Y 2
#define ADIS16209_SCAN_INCLI_Y 6
#define ADIS16209_SCAN_ROT 7
+#ifdef CONFIG_IIO_RING_BUFFER
+
void adis16209_remove_trigger(struct iio_dev *indio_dev);
int adis16209_probe_trigger(struct iio_dev *indio_dev);
int adis16260_set_irq(struct iio_dev *indio_dev, bool enable);
-#ifdef CONFIG_IIO_RING_BUFFER
/* At the moment triggers are only used for ring buffer
* filling. This may change!
*/
#define ADIS16260_SCAN_TEMP 3
#define ADIS16260_SCAN_ANGL 4
+#ifdef CONFIG_IIO_RING_BUFFER
void adis16260_remove_trigger(struct iio_dev *indio_dev);
int adis16260_probe_trigger(struct iio_dev *indio_dev);
int adis16400_set_irq(struct iio_dev *indio_dev, bool enable);
-#ifdef CONFIG_IIO_RING_BUFFER
/* At the moment triggers are only used for ring buffer
* filling. This may change!
*/
#define ADIS16300_SCAN_INCLI_X 12
#define ADIS16300_SCAN_INCLI_Y 13
+#ifdef CONFIG_IIO_RING_BUFFER
void adis16400_remove_trigger(struct iio_dev *indio_dev);
int adis16400_probe_trigger(struct iio_dev *indio_dev);
mutex_lock(&dev->device_lock);
}
- if (!err && !dev->recvd_msg) {
+ if (err <= 0 && !dev->recvd_msg) {
dev->mei_state = MEI_DISABLED;
dev_dbg(&dev->pdev->dev,
"wait_event_interruptible_timeout failed"
ret = wait_event_interruptible_timeout(dev->wait_stop_wd,
dev->wd_stopped, 10 * HZ);
mutex_lock(&dev->device_lock);
- if (!dev->wd_stopped)
- dev_dbg(&dev->pdev->dev, "stop wd failed to complete.\n");
- else
- dev_dbg(&dev->pdev->dev, "stop wd complete.\n");
+ if (dev->wd_stopped) {
+ dev_dbg(&dev->pdev->dev, "stop wd complete ret=%d.\n", ret);
+ ret = 0;
+ } else {
+ if (!ret)
+ ret = -ETIMEDOUT;
+ dev_warn(&dev->pdev->dev,
+ "stop wd failed to complete ret=%d.\n", ret);
+ }
if (preserve)
dev->wd_timeout = wd_timeout;
*/
se_cmd->se_tmr_req = core_tmr_alloc_req(se_cmd, (void *)tl_tmr,
TMR_LUN_RESET);
- if (!se_cmd->se_tmr_req)
+ if (IS_ERR(se_cmd->se_tmr_req))
goto release;
/*
* Locate the underlying TCM struct se_lun from sc->device->lun
struct se_portal_group *se_tpg;
struct tcm_loop_hba *tl_hba = tl_tpg->tl_hba;
struct tcm_loop_nexus *tl_nexus;
+ int ret = -ENOMEM;
if (tl_tpg->tl_hba->tl_nexus) {
printk(KERN_INFO "tl_tpg->tl_hba->tl_nexus already exists\n");
* Initialize the struct se_session pointer
*/
tl_nexus->se_sess = transport_init_session();
- if (!tl_nexus->se_sess)
+ if (IS_ERR(tl_nexus->se_sess)) {
+ ret = PTR_ERR(tl_nexus->se_sess);
goto out;
+ }
/*
* Since we are running in 'demo mode' this call with generate a
* struct se_node_acl for the tcm_loop struct se_portal_group with the SCSI
out:
kfree(tl_nexus);
- return -ENOMEM;
+ return ret;
}
static int tcm_loop_drop_nexus(
* the fabric protocol_id set in tcm_loop_make_scsi_hba(), and call
* tcm_loop_make_nexus()
*/
- if (strlen(page) > TL_WWN_ADDR_LEN) {
+ if (strlen(page) >= TL_WWN_ADDR_LEN) {
printk(KERN_ERR "Emulated NAA Sas Address: %s, exceeds"
" max: %d\n", page, TL_WWN_ADDR_LEN);
return -EINVAL;
return ERR_PTR(-EINVAL);
check_len:
- if (strlen(name) > TL_WWN_ADDR_LEN) {
+ if (strlen(name) >= TL_WWN_ADDR_LEN) {
printk(KERN_ERR "Emulated NAA %s Address: %s, exceeds"
" max: %d\n", name, tcm_loop_dump_proto_id(tl_hba),
TL_WWN_ADDR_LEN);
printk(KERN_ERR "Unable to locate passed fabric name\n");
return NULL;
}
- if (strlen(name) > TARGET_FABRIC_NAME_SIZE) {
+ if (strlen(name) >= TARGET_FABRIC_NAME_SIZE) {
printk(KERN_ERR "Passed name: %s exceeds TARGET_FABRIC"
"_NAME_SIZE\n", name);
return NULL;
tf = kzalloc(sizeof(struct target_fabric_configfs), GFP_KERNEL);
if (!(tf))
- return ERR_PTR(-ENOMEM);
+ return NULL;
INIT_LIST_HEAD(&tf->tf_list);
atomic_set(&tf->tf_access_cnt, 0);
return -EOPNOTSUPP;
}
- if ((strlen(page) + 1) > INQUIRY_VPD_SERIAL_LEN) {
+ if (strlen(page) >= INQUIRY_VPD_SERIAL_LEN) {
printk(KERN_ERR "Emulated VPD Unit Serial exceeds"
" INQUIRY_VPD_SERIAL_LEN: %d\n", INQUIRY_VPD_SERIAL_LEN);
return -EOVERFLOW;
transport_dump_vpd_proto_id(vpd, buf, VPD_TMP_BUF_SIZE);
- if ((len + strlen(buf) > PAGE_SIZE))
+ if ((len + strlen(buf) >= PAGE_SIZE))
break;
len += sprintf(page+len, "%s", buf);
\
memset(buf, 0, VPD_TMP_BUF_SIZE); \
transport_dump_vpd_assoc(vpd, buf, VPD_TMP_BUF_SIZE); \
- if ((len + strlen(buf) > PAGE_SIZE)) \
+ if ((len + strlen(buf) >= PAGE_SIZE)) \
break; \
len += sprintf(page+len, "%s", buf); \
\
memset(buf, 0, VPD_TMP_BUF_SIZE); \
transport_dump_vpd_ident_type(vpd, buf, VPD_TMP_BUF_SIZE); \
- if ((len + strlen(buf) > PAGE_SIZE)) \
+ if ((len + strlen(buf) >= PAGE_SIZE)) \
break; \
len += sprintf(page+len, "%s", buf); \
\
memset(buf, 0, VPD_TMP_BUF_SIZE); \
transport_dump_vpd_ident(vpd, buf, VPD_TMP_BUF_SIZE); \
- if ((len + strlen(buf) > PAGE_SIZE)) \
+ if ((len + strlen(buf) >= PAGE_SIZE)) \
break; \
len += sprintf(page+len, "%s", buf); \
} \
&i_buf[0] : "", pr_reg->pr_res_key,
pr_reg->pr_res_generation);
- if ((len + strlen(buf) > PAGE_SIZE))
+ if ((len + strlen(buf) >= PAGE_SIZE))
break;
len += sprintf(page+len, "%s", buf);
ret = -ENOMEM;
goto out;
}
- if (strlen(i_port) > PR_APTPL_MAX_IPORT_LEN) {
+ if (strlen(i_port) >= PR_APTPL_MAX_IPORT_LEN) {
printk(KERN_ERR "APTPL metadata initiator_node="
" exceeds PR_APTPL_MAX_IPORT_LEN: %d\n",
PR_APTPL_MAX_IPORT_LEN);
ret = -ENOMEM;
goto out;
}
- if (strlen(isid) > PR_REG_ISID_LEN) {
+ if (strlen(isid) >= PR_REG_ISID_LEN) {
printk(KERN_ERR "APTPL metadata initiator_isid"
"= exceeds PR_REG_ISID_LEN: %d\n",
PR_REG_ISID_LEN);
ret = -ENOMEM;
goto out;
}
- if (strlen(t_port) > PR_APTPL_MAX_TPORT_LEN) {
+ if (strlen(t_port) >= PR_APTPL_MAX_TPORT_LEN) {
printk(KERN_ERR "APTPL metadata target_node="
" exceeds PR_APTPL_MAX_TPORT_LEN: %d\n",
PR_APTPL_MAX_TPORT_LEN);
int ret;
memset(buf, 0, TARGET_CORE_NAME_MAX_LEN);
- if (strlen(name) > TARGET_CORE_NAME_MAX_LEN) {
+ if (strlen(name) >= TARGET_CORE_NAME_MAX_LEN) {
printk(KERN_ERR "Passed *name strlen(): %d exceeds"
" TARGET_CORE_NAME_MAX_LEN: %d\n", (int)strlen(name),
TARGET_CORE_NAME_MAX_LEN);
&SE_NODE_ACL(se_sess)->device_list[unpacked_lun];
if (deve->lun_flags & TRANSPORT_LUNFLAGS_INITIATOR_ACCESS) {
se_lun = se_cmd->se_lun = se_tmr->tmr_lun = deve->se_lun;
- dev = se_tmr->tmr_dev = se_lun->lun_se_dev;
+ dev = se_lun->lun_se_dev;
se_cmd->pr_res_key = deve->pr_res_key;
se_cmd->orig_fe_lun = unpacked_lun;
se_cmd->se_orig_obj_ptr = SE_LUN(se_cmd)->lun_se_dev;
se_cmd->se_cmd_flags |= SCF_SCSI_CDB_EXCEPTION;
return -1;
}
+ se_tmr->tmr_dev = dev;
spin_lock(&dev->se_tmr_lock);
list_add_tail(&se_tmr->tmr_list, &dev->dev_tmr_list);
struct se_lun_acl *lacl;
struct se_node_acl *nacl;
- if (strlen(initiatorname) > TRANSPORT_IQN_LEN) {
+ if (strlen(initiatorname) >= TRANSPORT_IQN_LEN) {
printk(KERN_ERR "%s InitiatorName exceeds maximum size.\n",
TPG_TFO(tpg)->get_fabric_name());
*ret = -EOVERFLOW;
pr_reg->pr_res_mapped_lun);
}
- if ((len + strlen(tmp) > pr_aptpl_buf_len)) {
+ if ((len + strlen(tmp) >= pr_aptpl_buf_len)) {
printk(KERN_ERR "Unable to update renaming"
" APTPL metadata\n");
spin_unlock(&T10_RES(su_dev)->registration_lock);
TPG_TFO(tpg)->tpg_get_tag(tpg),
lun->lun_sep->sep_rtpi, lun->unpacked_lun, reg_count);
- if ((len + strlen(tmp) > pr_aptpl_buf_len)) {
+ if ((len + strlen(tmp) >= pr_aptpl_buf_len)) {
printk(KERN_ERR "Unable to update renaming"
" APTPL metadata\n");
spin_unlock(&T10_RES(su_dev)->registration_lock);
memset(iov, 0, sizeof(struct iovec));
memset(path, 0, 512);
- if (strlen(&wwn->unit_serial[0]) > 512) {
+ if (strlen(&wwn->unit_serial[0]) >= 512) {
printk(KERN_ERR "WWN value for struct se_device does not fit"
" into path buffer\n");
return -1;
{
struct se_device *dev = tmr->tmr_dev;
+ if (!dev) {
+ kmem_cache_free(se_tmr_req_cache, tmr);
+ return;
+ }
+
spin_lock(&dev->se_tmr_lock);
list_del(&tmr->tmr_list);
- kmem_cache_free(se_tmr_req_cache, tmr);
spin_unlock(&dev->se_tmr_lock);
+
+ kmem_cache_free(se_tmr_req_cache, tmr);
}
static void core_tmr_handle_tas_abort(
void transport_deregister_session_configfs(struct se_session *se_sess)
{
struct se_node_acl *se_nacl;
-
+ unsigned long flags;
/*
* Used by struct se_node_acl's under ConfigFS to locate active struct se_session
*/
se_nacl = se_sess->se_node_acl;
if ((se_nacl)) {
- spin_lock_irq(&se_nacl->nacl_sess_lock);
+ spin_lock_irqsave(&se_nacl->nacl_sess_lock, flags);
list_del(&se_sess->sess_acl_list);
/*
* If the session list is empty, then clear the pointer.
se_nacl->acl_sess_list.prev,
struct se_session, sess_acl_list);
}
- spin_unlock_irq(&se_nacl->nacl_sess_lock);
+ spin_unlock_irqrestore(&se_nacl->nacl_sess_lock, flags);
}
}
EXPORT_SYMBOL(transport_deregister_session_configfs);
*/
struct ft_cmd {
enum ft_cmd_state state;
- u16 lun; /* LUN from request */
+ u32 lun; /* LUN from request */
struct ft_sess *sess; /* session held for cmd */
struct fc_seq *seq; /* sequence in exchange mgr */
struct se_cmd se_cmd; /* Local TCM I/O descriptor */
16, 4, cmd->cdb, MAX_COMMAND_SIZE, 0);
}
-/*
- * Get LUN from CDB.
- */
-static int ft_get_lun_for_cmd(struct ft_cmd *cmd, u8 *lunp)
-{
- u64 lun;
-
- lun = lunp[1];
- switch (lunp[0] >> 6) {
- case 0:
- break;
- case 1:
- lun |= (lunp[0] & 0x3f) << 8;
- break;
- default:
- return -1;
- }
- if (lun >= TRANSPORT_MAX_LUNS_PER_TPG)
- return -1;
- cmd->lun = lun;
- return transport_get_lun_for_cmd(&cmd->se_cmd, NULL, lun);
-}
-
static void ft_queue_cmd(struct ft_sess *sess, struct ft_cmd *cmd)
{
struct se_queue_obj *qobj;
{
struct se_tmr_req *tmr;
struct fcp_cmnd *fcp;
+ struct ft_sess *sess;
u8 tm_func;
fcp = fc_frame_payload_get(cmd->req_frame, sizeof(*fcp));
switch (fcp->fc_tm_flags) {
case FCP_TMF_LUN_RESET:
tm_func = TMR_LUN_RESET;
- if (ft_get_lun_for_cmd(cmd, fcp->fc_lun) < 0) {
- ft_dump_cmd(cmd, __func__);
- transport_send_check_condition_and_sense(&cmd->se_cmd,
- cmd->se_cmd.scsi_sense_reason, 0);
- ft_sess_put(cmd->sess);
- return;
- }
break;
case FCP_TMF_TGT_RESET:
tm_func = TMR_TARGET_WARM_RESET;
return;
}
cmd->se_cmd.se_tmr_req = tmr;
+
+ switch (fcp->fc_tm_flags) {
+ case FCP_TMF_LUN_RESET:
+ cmd->lun = scsilun_to_int((struct scsi_lun *)fcp->fc_lun);
+ if (transport_get_lun_for_tmr(&cmd->se_cmd, cmd->lun) < 0) {
+ /*
+ * Make sure to clean up newly allocated TMR request
+ * since "unable to handle TMR request because failed
+ * to get to LUN"
+ */
+ FT_TM_DBG("Failed to get LUN for TMR func %d, "
+ "se_cmd %p, unpacked_lun %d\n",
+ tm_func, &cmd->se_cmd, cmd->lun);
+ ft_dump_cmd(cmd, __func__);
+ sess = cmd->sess;
+ transport_send_check_condition_and_sense(&cmd->se_cmd,
+ cmd->se_cmd.scsi_sense_reason, 0);
+ transport_generic_free_cmd(&cmd->se_cmd, 0, 1, 0);
+ ft_sess_put(sess);
+ return;
+ }
+ break;
+ case FCP_TMF_TGT_RESET:
+ case FCP_TMF_CLR_TASK_SET:
+ case FCP_TMF_ABT_TASK_SET:
+ case FCP_TMF_CLR_ACA:
+ break;
+ default:
+ return;
+ }
transport_generic_handle_tmr(&cmd->se_cmd);
}
fc_seq_exch(cmd->seq)->lp->tt.seq_set_resp(cmd->seq, ft_recv_seq, cmd);
- ret = ft_get_lun_for_cmd(cmd, fcp->fc_lun);
+ cmd->lun = scsilun_to_int((struct scsi_lun *)fcp->fc_lun);
+ ret = transport_get_lun_for_cmd(&cmd->se_cmd, NULL, cmd->lun);
if (ret < 0) {
ft_dump_cmd(cmd, __func__);
transport_send_check_condition_and_sense(&cmd->se_cmd,
/* XXX For now, initiator will retry */
if (printk_ratelimit())
printk(KERN_ERR "%s: Failed to send frame %p, "
- "xid <0x%x>, remaining <0x%x>, "
+ "xid <0x%x>, remaining %zu, "
"lso_max <0x%x>\n",
__func__, fp, ep->xid,
remaining, lport->lso_max);
return NULL;
sess->se_sess = transport_init_session();
- if (!sess->se_sess) {
+ if (IS_ERR(sess->se_sess)) {
kfree(sess);
return NULL;
}
lport = sess->tport->lport;
port_id = sess->port_id;
if (port_id == -1) {
- mutex_lock(&ft_lport_lock);
+ mutex_unlock(&ft_lport_lock);
return;
}
FT_SESS_DBG("port_id %x\n", port_id);
*dp++ = last << 7 | first << 6 | 1; /* EA */
len--;
}
- memcpy(dp, skb_pull(dlci->skb, len), len);
+ memcpy(dp, dlci->skb->data, len);
+ skb_pull(dlci->skb, len);
__gsm_data_queue(dlci, msg);
if (last)
dlci->skb = NULL;
*/
static void gsm_process_modem(struct tty_struct *tty, struct gsm_dlci *dlci,
- u32 modem)
+ u32 modem, int clen)
{
int mlines = 0;
- u8 brk = modem >> 6;
+ u8 brk = 0;
+
+ /* The modem status command can either contain one octet (v.24 signals)
+ or two octets (v.24 signals + break signals). The length field will
+ either be 2 or 3 respectively. This is specified in section
+ 5.4.6.3.7 of the 27.010 mux spec. */
+
+ if (clen == 2)
+ modem = modem & 0x7f;
+ else {
+ brk = modem & 0x7f;
+ modem = (modem >> 7) & 0x7f;
+ };
/* Flow control/ready to communicate */
if (modem & MDM_FC) {
return;
}
tty = tty_port_tty_get(&dlci->port);
- gsm_process_modem(tty, dlci, modem);
+ gsm_process_modem(tty, dlci, modem, clen);
if (tty) {
tty_wakeup(tty);
tty_kref_put(tty);
* open we shovel the bits down it, if not we drop them.
*/
-static void gsm_dlci_data(struct gsm_dlci *dlci, u8 *data, int len)
+static void gsm_dlci_data(struct gsm_dlci *dlci, u8 *data, int clen)
{
/* krefs .. */
struct tty_port *port = &dlci->port;
struct tty_struct *tty = tty_port_tty_get(port);
unsigned int modem = 0;
+ int len = clen;
if (debug & 16)
pr_debug("%d bytes for tty %p\n", len, tty);
if (len == 0)
return;
}
- gsm_process_modem(tty, dlci, modem);
+ gsm_process_modem(tty, dlci, modem, clen);
/* Line state will go via DLCI 0 controls only */
case 1:
default:
/* FIXME: does n_tty_set_room need locking ? */
n_tty_set_room(tty);
timeout = schedule_timeout(timeout);
+ BUG_ON(!tty->read_buf);
continue;
}
__set_current_state(TASK_RUNNING);
uart->port.flags &= ~UPF_BOOT_AUTOCONF;
uart->port.type = PORT_UNKNOWN;
uart->port.dev = &serial8250_isa_devs->dev;
+ uart->capabilities = uart_config[uart->port.type].flags;
uart_add_one_port(&serial8250_reg, &uart->port);
} else {
uart->port.dev = NULL;
static int
pci_omegapci_setup(struct serial_private *priv,
- struct pciserial_board *board,
+ const struct pciserial_board *board,
struct uart_port *port, int idx)
{
return setup_port(priv, port, 2, idx * 8, 0);
return pci_default_setup(priv, board, port, idx);
}
+static int pci_eg20t_init(struct pci_dev *dev)
+{
+#if defined(CONFIG_SERIAL_PCH_UART) || defined(CONFIG_SERIAL_PCH_UART_MODULE)
+ return -ENODEV;
+#else
+ return 0;
+#endif
+}
+
/* This should be in linux/pci_ids.h */
#define PCI_VENDOR_ID_SBSMODULARIO 0x124B
#define PCI_SUBVENDOR_ID_SBSMODULARIO 0x124B
.init = pci_oxsemi_tornado_init,
.setup = pci_default_setup,
},
+ {
+ .vendor = PCI_VENDOR_ID_INTEL,
+ .device = 0x8811,
+ .init = pci_eg20t_init,
+ },
+ {
+ .vendor = PCI_VENDOR_ID_INTEL,
+ .device = 0x8812,
+ .init = pci_eg20t_init,
+ },
+ {
+ .vendor = PCI_VENDOR_ID_INTEL,
+ .device = 0x8813,
+ .init = pci_eg20t_init,
+ },
+ {
+ .vendor = PCI_VENDOR_ID_INTEL,
+ .device = 0x8814,
+ .init = pci_eg20t_init,
+ },
+ {
+ .vendor = 0x10DB,
+ .device = 0x8027,
+ .init = pci_eg20t_init,
+ },
+ {
+ .vendor = 0x10DB,
+ .device = 0x8028,
+ .init = pci_eg20t_init,
+ },
+ {
+ .vendor = 0x10DB,
+ .device = 0x8029,
+ .init = pci_eg20t_init,
+ },
+ {
+ .vendor = 0x10DB,
+ .device = 0x800C,
+ .init = pci_eg20t_init,
+ },
+ {
+ .vendor = 0x10DB,
+ .device = 0x800D,
+ .init = pci_eg20t_init,
+ },
+ {
+ .vendor = 0x10DB,
+ .device = 0x800D,
+ .init = pci_eg20t_init,
+ },
/*
* Cronyx Omega PCI (PLX-chip based)
*/
#include <linux/dmaengine.h>
#include <linux/dma-mapping.h>
#include <linux/scatterlist.h>
+#include <linux/delay.h>
#include <asm/io.h>
#include <asm/sizes.h>
#define UART_DR_ERROR (UART011_DR_OE|UART011_DR_BE|UART011_DR_PE|UART011_DR_FE)
#define UART_DUMMY_DR_RX (1 << 16)
+
+#define UART_WA_SAVE_NR 14
+
+static void pl011_lockup_wa(unsigned long data);
+static const u32 uart_wa_reg[UART_WA_SAVE_NR] = {
+ ST_UART011_DMAWM,
+ ST_UART011_TIMEOUT,
+ ST_UART011_LCRH_RX,
+ UART011_IBRD,
+ UART011_FBRD,
+ ST_UART011_LCRH_TX,
+ UART011_IFLS,
+ ST_UART011_XFCR,
+ ST_UART011_XON1,
+ ST_UART011_XON2,
+ ST_UART011_XOFF1,
+ ST_UART011_XOFF2,
+ UART011_CR,
+ UART011_IMSC
+};
+
+static u32 uart_wa_regdata[UART_WA_SAVE_NR];
+static DECLARE_TASKLET(pl011_lockup_tlet, pl011_lockup_wa, 0);
+
/* There is by now at least one vendor with differing details, so handle it */
struct vendor_data {
unsigned int ifls;
unsigned int lcrh_tx;
unsigned int lcrh_rx;
bool oversampling;
+ bool interrupt_may_hang; /* vendor-specific */
bool dma_threshold;
};
.lcrh_tx = ST_UART011_LCRH_TX,
.lcrh_rx = ST_UART011_LCRH_RX,
.oversampling = true,
+ .interrupt_may_hang = true,
.dma_threshold = true,
};
+static struct uart_amba_port *amba_ports[UART_NR];
+
/* Deals with DMA transactions */
struct pl011_sgbuf {
unsigned int lcrh_rx; /* vendor-specific */
bool autorts;
char type[12];
+ bool interrupt_may_hang; /* vendor-specific */
#ifdef CONFIG_DMA_ENGINE
/* DMA stuff */
bool using_tx_dma;
#endif
+/*
+ * pl011_lockup_wa
+ * This workaround aims to break the deadlock situation
+ * when after long transfer over uart in hardware flow
+ * control, uart interrupt registers cannot be cleared.
+ * Hence uart transfer gets blocked.
+ *
+ * It is seen that during such deadlock condition ICR
+ * don't get cleared even on multiple write. This leads
+ * pass_counter to decrease and finally reach zero. This
+ * can be taken as trigger point to run this UART_BT_WA.
+ *
+ */
+static void pl011_lockup_wa(unsigned long data)
+{
+ struct uart_amba_port *uap = amba_ports[0];
+ void __iomem *base = uap->port.membase;
+ struct circ_buf *xmit = &uap->port.state->xmit;
+ struct tty_struct *tty = uap->port.state->port.tty;
+ int buf_empty_retries = 200;
+ int loop;
+
+ /* Stop HCI layer from submitting data for tx */
+ tty->hw_stopped = 1;
+ while (!uart_circ_empty(xmit)) {
+ if (buf_empty_retries-- == 0)
+ break;
+ udelay(100);
+ }
+
+ /* Backup registers */
+ for (loop = 0; loop < UART_WA_SAVE_NR; loop++)
+ uart_wa_regdata[loop] = readl(base + uart_wa_reg[loop]);
+
+ /* Disable UART so that FIFO data is flushed out */
+ writew(0x00, uap->port.membase + UART011_CR);
+
+ /* Soft reset UART module */
+ if (uap->port.dev->platform_data) {
+ struct amba_pl011_data *plat;
+
+ plat = uap->port.dev->platform_data;
+ if (plat->reset)
+ plat->reset();
+ }
+
+ /* Restore registers */
+ for (loop = 0; loop < UART_WA_SAVE_NR; loop++)
+ writew(uart_wa_regdata[loop] ,
+ uap->port.membase + uart_wa_reg[loop]);
+
+ /* Initialise the old status of the modem signals */
+ uap->old_status = readw(uap->port.membase + UART01x_FR) &
+ UART01x_FR_MODEM_ANY;
+
+ if (readl(base + UART011_MIS) & 0x2)
+ printk(KERN_EMERG "UART_BT_WA: ***FAILED***\n");
+
+ /* Start Tx/Rx */
+ tty->hw_stopped = 0;
+}
+
static void pl011_stop_tx(struct uart_port *port)
{
struct uart_amba_port *uap = (struct uart_amba_port *)port;
if (status & UART011_TXIS)
pl011_tx_chars(uap);
- if (pass_counter-- == 0)
+ if (pass_counter-- == 0) {
+ if (uap->interrupt_may_hang)
+ tasklet_schedule(&pl011_lockup_tlet);
break;
+ }
status = readw(uap->port.membase + UART011_MIS);
} while (status != 0);
writew(uap->im, uap->port.membase + UART011_IMSC);
spin_unlock_irq(&uap->port.lock);
+ if (uap->port.dev->platform_data) {
+ struct amba_pl011_data *plat;
+
+ plat = uap->port.dev->platform_data;
+ if (plat->init)
+ plat->init();
+ }
+
return 0;
clk_dis:
* Shut down the clock producer
*/
clk_disable(uap->clk);
+
+ if (uap->port.dev->platform_data) {
+ struct amba_pl011_data *plat;
+
+ plat = uap->port.dev->platform_data;
+ if (plat->exit)
+ plat->exit();
+ }
+
}
static void
if (!uap)
return -ENODEV;
+ if (uap->port.dev->platform_data) {
+ struct amba_pl011_data *plat;
+
+ plat = uap->port.dev->platform_data;
+ if (plat->init)
+ plat->init();
+ }
+
uap->port.uartclk = clk_get_rate(uap->clk);
if (options)
uap->lcrh_rx = vendor->lcrh_rx;
uap->lcrh_tx = vendor->lcrh_tx;
uap->fifosize = vendor->fifosize;
+ uap->interrupt_may_hang = vendor->interrupt_may_hang;
uap->port.dev = &dev->dev;
uap->port.mapbase = dev->res.start;
uap->port.membase = base;
/* get overrun/fifo empty information from ier
* register */
iestat = bcm_uart_readl(port, UART_IR_REG);
+
+ if (unlikely(iestat & UART_IR_STAT(UART_IR_RXOVER))) {
+ unsigned int val;
+
+ /* fifo reset is required to clear
+ * interrupt */
+ val = bcm_uart_readl(port, UART_CTL_REG);
+ val |= UART_CTL_RSTRXFIFO_MASK;
+ bcm_uart_writel(port, val, UART_CTL_REG);
+
+ port->icount.overrun++;
+ tty_insert_flip_char(tty, 0, TTY_OVERRUN);
+ }
+
if (!(iestat & UART_IR_STAT(UART_IR_RXNOTEMPTY)))
break;
if (uart_handle_sysrq_char(port, c))
continue;
- if (unlikely(iestat & UART_IR_STAT(UART_IR_RXOVER))) {
- port->icount.overrun++;
- tty_insert_flip_char(tty, 0, TTY_OVERRUN);
- }
if ((cstat & port->ignore_status_mask) == 0)
tty_insert_flip_char(tty, c, flag);
brd->bd_uart_offset = 0x200;
brd->bd_dividend = 921600;
- brd->re_map_membase = ioremap(brd->membase, 0x1000);
+ brd->re_map_membase = ioremap(brd->membase, pci_resource_len(pdev, 0));
if (!brd->re_map_membase) {
dev_err(&pdev->dev,
"card has no PCI Memory resources, "
int ret = 0;
struct circ_buf *xmit = &max->con_xmit;
- init_waitqueue_head(wq);
pr_info(PR_FMT "start main thread\n");
do {
res = RC_TAG;
ret = max3110_write_then_read(max, (u8 *)&res, (u8 *)&res, 2, 0);
if (ret < 0 || res == 0 || res == 0xffff) {
- printk(KERN_ERR "MAX3111 deemed not present (conf reg %04x)",
+ dev_dbg(&spi->dev, "MAX3111 deemed not present (conf reg %04x)",
res);
ret = -ENODEV;
goto err_get_page;
max->con_xmit.head = 0;
max->con_xmit.tail = 0;
+ init_waitqueue_head(&max->wq);
+
max->main_thread = kthread_run(max3110_main_thread,
max, "max3110_main");
if (IS_ERR(max->main_thread)) {
struct s3c2410_uartcfg *cfg = port->dev->platform_data;
unsigned long ucon = rd_regl(port, S3C2410_UCON);
- if ((cfg->clocks_size) == 1)
+ if (cfg->flags & NO_NEED_CHECK_CLKSRC)
return 0;
if (strcmp(clk->name, "pclk") == 0)
clk->divisor = 1;
- if ((cfg->clocks_size) == 1)
+ if (cfg->flags & NO_NEED_CHECK_CLKSRC)
return 0;
switch (ucon & S5PV210_UCON_CLKMASK) {
static int tty_ldisc_wait_idle(struct tty_struct *tty)
{
int ret;
- ret = wait_event_interruptible_timeout(tty_ldisc_idle,
+ ret = wait_event_timeout(tty_ldisc_idle,
atomic_read(&tty->ldisc->users) == 1, 5 * HZ);
if (ret < 0)
return ret;
if (IS_ERR(ld))
return -1;
+ WARN_ON_ONCE(tty_ldisc_wait_idle(tty));
+
tty_ldisc_close(tty, tty->ldisc);
tty_ldisc_put(tty->ldisc);
tty->ldisc = NULL;
for (i = n - 1; i >= 0; --i) {
intf = udev->actconfig->interface[i];
status = usb_suspend_interface(udev, intf, msg);
+
+ /* Ignore errors during system sleep transitions */
+ if (!(msg.event & PM_EVENT_AUTO))
+ status = 0;
if (status != 0)
break;
}
}
- if (status == 0)
+ if (status == 0) {
status = usb_suspend_device(udev, msg);
+ /* Again, ignore errors during system sleep transitions */
+ if (!(msg.event & PM_EVENT_AUTO))
+ status = 0;
+ }
+
/* If the suspend failed, resume interfaces that did get suspended */
if (status != 0) {
msg.event ^= (PM_EVENT_SUSPEND | PM_EVENT_RESUME);
{
struct usb_device *udev = *pdev;
int i;
+ struct usb_hcd *hcd = bus_to_hcd(udev->bus);
if (!udev) {
pr_debug ("%s nodev\n", __func__);
* so that the hardware is now fully quiesced.
*/
dev_dbg (&udev->dev, "unregistering device\n");
+ mutex_lock(hcd->bandwidth_mutex);
usb_disable_device(udev, 0);
+ mutex_unlock(hcd->bandwidth_mutex);
usb_hcd_synchronize_unlinks(udev);
usb_remove_ep_devs(&udev->ep0);
USB_DEVICE_REMOTE_WAKEUP, 0,
NULL, 0,
USB_CTRL_SET_TIMEOUT);
+
+ /* System sleep transitions should never fail */
+ if (!(msg.event & PM_EVENT_AUTO))
+ status = 0;
} else {
/* device has up to 10 msec to fully suspend */
dev_dbg(&udev->dev, "usb %ssuspend\n",
struct usb_device *hdev = hub->hdev;
unsigned port1;
- /* fail if children aren't already suspended */
+ /* Warn if children aren't already suspended */
for (port1 = 1; port1 <= hdev->maxchild; port1++) {
struct usb_device *udev;
udev = hdev->children [port1-1];
if (udev && udev->can_submit) {
- if (!(msg.event & PM_EVENT_AUTO))
- dev_dbg(&intf->dev, "port %d nyet suspended\n",
- port1);
- return -EBUSY;
+ dev_warn(&intf->dev, "port %d nyet suspended\n", port1);
+ if (msg.event & PM_EVENT_AUTO)
+ return -EBUSY;
}
}
* Deallocates hcd/hardware state for the endpoints (nuking all or most
* pending urbs) and usbcore state for the interfaces, so that usbcore
* must usb_set_configuration() before any interfaces could be used.
+ *
+ * Must be called with hcd->bandwidth_mutex held.
*/
void usb_disable_device(struct usb_device *dev, int skip_ep0)
{
int i;
+ struct usb_hcd *hcd = bus_to_hcd(dev->bus);
/* getting rid of interfaces will disconnect
* any drivers bound to them (a key side effect)
dev_dbg(&dev->dev, "%s nuking %s URBs\n", __func__,
skip_ep0 ? "non-ep0" : "all");
+ if (hcd->driver->check_bandwidth) {
+ /* First pass: Cancel URBs, leave endpoint pointers intact. */
+ for (i = skip_ep0; i < 16; ++i) {
+ usb_disable_endpoint(dev, i, false);
+ usb_disable_endpoint(dev, i + USB_DIR_IN, false);
+ }
+ /* Remove endpoints from the host controller internal state */
+ usb_hcd_alloc_bandwidth(dev, NULL, NULL, NULL);
+ /* Second pass: remove endpoint pointers */
+ }
for (i = skip_ep0; i < 16; ++i) {
usb_disable_endpoint(dev, i, true);
usb_disable_endpoint(dev, i + USB_DIR_IN, true);
/* if it's already configured, clear out old state first.
* getting rid of old interfaces means unbinding their drivers.
*/
+ mutex_lock(hcd->bandwidth_mutex);
if (dev->state != USB_STATE_ADDRESS)
usb_disable_device(dev, 1); /* Skip ep0 */
* host controller will not allow submissions to dropped endpoints. If
* this call fails, the device state is unchanged.
*/
- mutex_lock(hcd->bandwidth_mutex);
ret = usb_hcd_alloc_bandwidth(dev, cp, NULL, NULL);
if (ret < 0) {
mutex_unlock(hcd->bandwidth_mutex);
struct ehci_hcd *ehci = hcd_to_ehci(hcd);
struct platform_device *pdev = to_platform_device(hcd->self.controller);
const struct platform_device_id *id;
- int hclength;
int ret;
id = platform_get_device_id(pdev);
return -EINVAL;
}
- hclength = HC_LENGTH(ehci, ehci_readl(ehci, &ehci->caps->hc_capbase));
switch (id->driver_data) {
case EHCI_ATH79_IP_V1:
ehci->has_synopsys_hc_bug = 1;
ehci->caps = hcd->regs;
- ehci->regs = hcd->regs + hclength;
+ ehci->regs = hcd->regs +
+ HC_LENGTH(ehci,
+ ehci_readl(ehci, &ehci->caps->hc_capbase));
break;
case EHCI_ATH79_IP_V2:
hcd->has_tt = 1;
ehci->caps = hcd->regs + 0x100;
- ehci->regs = hcd->regs + 0x100 + hclength;
+ ehci->regs = hcd->regs + 0x100 +
+ HC_LENGTH(ehci,
+ ehci_readl(ehci, &ehci->caps->hc_capbase));
break;
default:
/*
+ * Enhanced Host Controller Interface (EHCI) driver for USB.
+ *
+ * Maintainer: Alan Stern <stern@rowland.harvard.edu>
+ *
* Copyright (c) 2000-2004 by David Brownell
*
* This program is free software; you can redistribute it and/or modify it
/* We need to forcefully reclaim the slot since some transfers never
return, e.g. interrupt transfers and NAKed bulk transfers. */
- if (usb_pipebulk(urb->pipe)) {
+ if (usb_pipecontrol(urb->pipe) || usb_pipebulk(urb->pipe)) {
skip_map = reg_read32(hcd->regs, HC_ATL_PTD_SKIPMAP_REG);
skip_map |= (1 << qh->slot);
reg_write32(hcd->regs, HC_ATL_PTD_SKIPMAP_REG, skip_map);
/*
- * OHCI HCD (Host Controller Driver) for USB.
+ * Open Host Controller Interface (OHCI) driver for USB.
+ *
+ * Maintainer: Alan Stern <stern@rowland.harvard.edu>
*
* (C) Copyright 1999 Roman Weissgaerber <weissg@vienna.at>
* (C) Copyright 2000-2004 David Brownell <dbrownell@users.sourceforge.net>
INIT_LIST_HEAD(&r8a66597->child_device);
hcd->rsrc_start = res->start;
+ hcd->has_tt = 1;
ret = usb_add_hcd(hcd, irq, IRQF_DISABLED | irq_trigger);
if (ret != 0) {
ep_ctx->ep_info2 |= cpu_to_le32(MAX_PACKET(max_packet));
/* dig out max burst from ep companion desc */
max_packet = ep->ss_ep_comp.bMaxBurst;
- if (!max_packet)
- xhci_warn(xhci, "WARN no SS endpoint bMaxBurst\n");
ep_ctx->ep_info2 |= cpu_to_le32(MAX_BURST(max_packet));
break;
case USB_SPEED_HIGH:
#define PCI_VENDOR_ID_FRESCO_LOGIC 0x1b73
#define PCI_DEVICE_ID_FRESCO_LOGIC_PDK 0x1000
+#define PCI_VENDOR_ID_ETRON 0x1b6f
+#define PCI_DEVICE_ID_ASROCK_P67 0x7023
+
static const char hcd_name[] = "xhci_hcd";
/* called after powerup, by probe or system-pm "wakeup" */
xhci->quirks |= XHCI_EP_LIMIT_QUIRK;
xhci->limit_active_eps = 64;
}
+ if (pdev->vendor == PCI_VENDOR_ID_ETRON &&
+ pdev->device == PCI_DEVICE_ID_ASROCK_P67) {
+ xhci->quirks |= XHCI_RESET_ON_RESUME;
+ xhci_dbg(xhci, "QUIRK: Resetting on resume\n");
+ }
/* Make sure the HC is halted. */
retval = xhci_halt(xhci);
frame->status = -EOVERFLOW;
skip_td = true;
break;
+ case COMP_DEV_ERR:
case COMP_STALL:
frame->status = -EPROTO;
skip_td = true;
}
}
- if ((idx == urb_priv->length - 1) && *status == -EINPROGRESS)
- *status = 0;
-
return finish_td(xhci, td, event_trb, event, ep, status, false);
}
idx = urb_priv->td_cnt;
frame = &td->urb->iso_frame_desc[idx];
- /* The transfer is partly done */
- *status = -EXDEV;
+ /* The transfer is partly done. */
frame->status = -EXDEV;
/* calc actual length */
TRB_TO_SLOT_ID(le32_to_cpu(event->flags)),
ep_index);
goto cleanup;
+ case COMP_DEV_ERR:
+ xhci_warn(xhci, "WARN: detect an incompatible device");
+ status = -EPROTO;
+ break;
case COMP_MISSED_INT:
/*
* When encounter missed service error, one or more isoc tds
/* Is this a TRB in the currently executing TD? */
event_seg = trb_in_td(ep_ring->deq_seg, ep_ring->dequeue,
td->last_trb, event_dma);
+
+ /*
+ * Skip the Force Stopped Event. The event_trb(event_dma) of FSE
+ * is not in the current TD pointed by ep_ring->dequeue because
+ * that the hardware dequeue pointer still at the previous TRB
+ * of the current TD. The previous TRB maybe a Link TD or the
+ * last TRB of the previous TD. The command completion handle
+ * will take care the rest.
+ */
+ if (!event_seg && trb_comp_code == COMP_STOP_INVAL) {
+ ret = 0;
+ goto cleanup;
+ }
+
if (!event_seg) {
if (!ep->skip ||
!usb_endpoint_xfer_isoc(&td->urb->ep->desc)) {
urb->transfer_buffer_length,
status);
spin_unlock(&xhci->lock);
+ /* EHCI, UHCI, and OHCI always unconditionally set the
+ * urb->status of an isochronous endpoint to 0.
+ */
+ if (usb_pipetype(urb->pipe) == PIPE_ISOCHRONOUS)
+ status = 0;
usb_hcd_giveback_urb(bus_to_hcd(urb->dev->bus), urb, status);
spin_lock(&xhci->lock);
}
msleep(100);
spin_lock_irq(&xhci->lock);
+ if (xhci->quirks & XHCI_RESET_ON_RESUME)
+ hibernated = true;
if (!hibernated) {
/* step 1: restore register */
u32 added_ctxs;
unsigned int last_ctx;
u32 new_add_flags, new_drop_flags, new_slot_info;
+ struct xhci_virt_device *virt_dev;
int ret = 0;
ret = xhci_check_args(hcd, udev, ep, 1, true, __func__);
return 0;
}
- in_ctx = xhci->devs[udev->slot_id]->in_ctx;
- out_ctx = xhci->devs[udev->slot_id]->out_ctx;
+ virt_dev = xhci->devs[udev->slot_id];
+ in_ctx = virt_dev->in_ctx;
+ out_ctx = virt_dev->out_ctx;
ctrl_ctx = xhci_get_input_control_ctx(xhci, in_ctx);
ep_index = xhci_get_endpoint_index(&ep->desc);
ep_ctx = xhci_get_ep_ctx(xhci, out_ctx, ep_index);
+
+ /* If this endpoint is already in use, and the upper layers are trying
+ * to add it again without dropping it, reject the addition.
+ */
+ if (virt_dev->eps[ep_index].ring &&
+ !(le32_to_cpu(ctrl_ctx->drop_flags) &
+ xhci_get_endpoint_flag(&ep->desc))) {
+ xhci_warn(xhci, "Trying to add endpoint 0x%x "
+ "without dropping it.\n",
+ (unsigned int) ep->desc.bEndpointAddress);
+ return -EINVAL;
+ }
+
/* If the HCD has already noted the endpoint is enabled,
* ignore this request.
*/
* process context, not interrupt context (or so documenation
* for usb_set_interface() and usb_set_configuration() claim).
*/
- if (xhci_endpoint_init(xhci, xhci->devs[udev->slot_id],
- udev, ep, GFP_NOIO) < 0) {
+ if (xhci_endpoint_init(xhci, virt_dev, udev, ep, GFP_NOIO) < 0) {
dev_dbg(&udev->dev, "%s - could not initialize ep %#x\n",
__func__, ep->desc.bEndpointAddress);
return -ENOMEM;
"and endpoint is not disabled.\n");
ret = -EINVAL;
break;
+ case COMP_DEV_ERR:
+ dev_warn(&udev->dev, "ERROR: Incompatible device for endpoint "
+ "configure command.\n");
+ ret = -ENODEV;
+ break;
case COMP_SUCCESS:
dev_dbg(&udev->dev, "Successful Endpoint Configure command\n");
ret = 0;
xhci_dbg_ctx(xhci, virt_dev->out_ctx, 1);
ret = -EINVAL;
break;
+ case COMP_DEV_ERR:
+ dev_warn(&udev->dev, "ERROR: Incompatible device for evaluate "
+ "context command.\n");
+ ret = -ENODEV;
+ break;
case COMP_MEL_ERR:
/* Max Exit Latency too large error */
dev_warn(&udev->dev, "WARN: Max Exit Latency too large\n");
dev_warn(&udev->dev, "Device not responding to set address.\n");
ret = -EPROTO;
break;
+ case COMP_DEV_ERR:
+ dev_warn(&udev->dev, "ERROR: Incompatible device for address "
+ "device command.\n");
+ ret = -ENODEV;
+ break;
case COMP_SUCCESS:
xhci_dbg(xhci, "Successful Address Device command\n");
break;
#define COMP_PING_ERR 20
/* Event Ring is full */
#define COMP_ER_FULL 21
+/* Incompatible Device Error */
+#define COMP_DEV_ERR 22
/* Missed Service Error - HC couldn't service an isoc ep within interval */
#define COMP_MISSED_INT 23
/* Successfully stopped command ring */
*/
#define XHCI_EP_LIMIT_QUIRK (1 << 5)
#define XHCI_BROKEN_MSI (1 << 6)
+#define XHCI_RESET_ON_RESUME (1 << 7)
unsigned int num_active_eps;
unsigned int limit_active_eps;
/* There are two roothubs to keep track of bus suspend info for */
csr = musb_readw(epio, MUSB_TXCSR);
if (csr & MUSB_TXCSR_FIFONOTEMPTY) {
csr |= MUSB_TXCSR_FLUSHFIFO | MUSB_TXCSR_P_WZC_BITS;
+ /*
+ * Setting both TXPKTRDY and FLUSHFIFO makes controller
+ * to interrupt current FIFO loading, but not flushing
+ * the already loaded ones.
+ */
+ csr &= ~MUSB_TXCSR_TXPKTRDY;
musb_writew(epio, MUSB_TXCSR, csr);
/* REVISIT may be inappropriate w/o FIFONOTEMPTY ... */
musb_writew(epio, MUSB_TXCSR, csr);
/* even if there was an error, we did the dma
* for iso_frame_desc->length
*/
- if (d->status != EILSEQ && d->status != -EOVERFLOW)
+ if (d->status != -EILSEQ && d->status != -EOVERFLOW)
d->status = 0;
if (++qh->iso_idx >= urb->number_of_packets)
{ USB_DEVICE(FTDI_VID, FTDI_232RL_PID) },
{ USB_DEVICE(FTDI_VID, FTDI_8U2232C_PID) },
{ USB_DEVICE(FTDI_VID, FTDI_4232H_PID) },
+ { USB_DEVICE(FTDI_VID, FTDI_232H_PID) },
{ USB_DEVICE(FTDI_VID, FTDI_MICRO_CHAMELEON_PID) },
{ USB_DEVICE(FTDI_VID, FTDI_RELAIS_PID) },
{ USB_DEVICE(FTDI_VID, FTDI_OPENDCC_PID) },
[FT2232C] = "FT2232C",
[FT232RL] = "FT232RL",
[FT2232H] = "FT2232H",
- [FT4232H] = "FT4232H"
+ [FT4232H] = "FT4232H",
+ [FT232H] = "FT232H"
};
break;
case FT2232H: /* FT2232H chip */
case FT4232H: /* FT4232H chip */
+ case FT232H: /* FT232H chip */
if ((baud <= 12000000) & (baud >= 1200)) {
div_value = ftdi_2232h_baud_to_divisor(baud);
} else if (baud < 1200) {
} else if (version < 0x600) {
/* Assume it's an FT232BM (or FT245BM) */
priv->chip_type = FT232BM;
- } else {
- /* Assume it's an FT232R */
+ } else if (version < 0x900) {
+ /* Assume it's an FT232RL */
priv->chip_type = FT232RL;
+ } else {
+ /* Assume it's an FT232H */
+ priv->chip_type = FT232H;
}
dev_info(&udev->dev, "Detected %s\n", ftdi_chip_name[priv->chip_type]);
}
priv->chip_type == FT2232C ||
priv->chip_type == FT232RL ||
priv->chip_type == FT2232H ||
- priv->chip_type == FT4232H)) {
+ priv->chip_type == FT4232H ||
+ priv->chip_type == FT232H)) {
retval = device_create_file(&port->dev,
&dev_attr_latency_timer);
}
priv->chip_type == FT2232C ||
priv->chip_type == FT232RL ||
priv->chip_type == FT2232H ||
- priv->chip_type == FT4232H) {
+ priv->chip_type == FT4232H ||
+ priv->chip_type == FT232H) {
device_remove_file(&port->dev, &dev_attr_latency_timer);
}
}
case FT232RL:
case FT2232H:
case FT4232H:
+ case FT232H:
len = 2;
break;
default:
FT2232C = 4,
FT232RL = 5,
FT2232H = 6,
- FT4232H = 7
+ FT4232H = 7,
+ FT232H = 8
};
enum ftdi_sio_baudrate {
#define FTDI_8U232AM_ALT_PID 0x6006 /* FTDI's alternate PID for above */
#define FTDI_8U2232C_PID 0x6010 /* Dual channel device */
#define FTDI_4232H_PID 0x6011 /* Quad channel hi-speed device */
+#define FTDI_232H_PID 0x6014 /* Single channel hi-speed device */
#define FTDI_SIO_PID 0x8372 /* Product Id SIO application of 8U100AX */
#define FTDI_232RL_PID 0xFBFA /* Product ID for FT232RL */
}
if (fw_p->size > TI_FIRMWARE_BUF_SIZE) {
dev_err(&dev->dev, "%s - firmware too large %zu\n", __func__, fw_p->size);
+ release_firmware(fw_p);
return -ENOENT;
}
config INTEL_SCU_WATCHDOG
bool "Intel SCU Watchdog for Mobile Platforms"
- depends on WATCHDOG
- depends on INTEL_SCU_IPC
+ depends on X86_MRST
---help---
Hardware driver for the watchdog time built into the Intel SCU
for Intel Mobile Platforms.
}
module_exit(at32_wdt_exit);
-MODULE_AUTHOR("Hans-Christian Egtvedt <hcegtvedt@atmel.com>");
+MODULE_AUTHOR("Hans-Christian Egtvedt <egtvedt@samfundet.no>");
MODULE_DESCRIPTION("Watchdog driver for Atmel AT32AP700X");
MODULE_LICENSE("GPL");
MODULE_ALIAS_MISCDEV(WATCHDOG_MINOR);
MODULE_DESCRIPTION("GE watchdog driver");
MODULE_LICENSE("GPL");
MODULE_ALIAS_MISCDEV(WATCHDOG_MINOR);
-MODULE_ALIAS("platform: gef_wdt");
+MODULE_ALIAS("platform:gef_wdt");
#include <linux/sched.h>
#include <linux/signal.h>
#include <linux/sfi.h>
-#include <linux/types.h>
#include <asm/irq.h>
#include <asm/atomic.h>
#include <asm/intel_scu_ipc.h>
int default_ticks;
unsigned long inuse;
unsigned gpio;
- int gstate;
+ unsigned int gstate;
} mtx1_wdt_device;
static void mtx1_wdt_trigger(unsigned long unused)
{
- u32 tmp;
-
spin_lock(&mtx1_wdt_device.lock);
if (mtx1_wdt_device.running)
ticks--;
/* toggle wdt gpio */
- mtx1_wdt_device.gstate = ~mtx1_wdt_device.gstate;
- if (mtx1_wdt_device.gstate)
- gpio_direction_output(mtx1_wdt_device.gpio, 1);
- else
- gpio_direction_input(mtx1_wdt_device.gpio);
+ mtx1_wdt_device.gstate = !mtx1_wdt_device.gstate;
+ gpio_set_value(mtx1_wdt_device.gpio, mtx1_wdt_device.gstate);
if (mtx1_wdt_device.queue && ticks)
mod_timer(&mtx1_wdt_device.timer, jiffies + MTX1_WDT_INTERVAL);
if (!mtx1_wdt_device.queue) {
mtx1_wdt_device.queue = 1;
mtx1_wdt_device.gstate = 1;
- gpio_direction_output(mtx1_wdt_device.gpio, 1);
+ gpio_set_value(mtx1_wdt_device.gpio, 1);
mod_timer(&mtx1_wdt_device.timer, jiffies + MTX1_WDT_INTERVAL);
}
mtx1_wdt_device.running++;
if (mtx1_wdt_device.queue) {
mtx1_wdt_device.queue = 0;
mtx1_wdt_device.gstate = 0;
- gpio_direction_output(mtx1_wdt_device.gpio, 0);
+ gpio_set_value(mtx1_wdt_device.gpio, 0);
}
ticks = mtx1_wdt_device.default_ticks;
spin_unlock_irqrestore(&mtx1_wdt_device.lock, flags);
int ret;
mtx1_wdt_device.gpio = pdev->resource[0].start;
+ ret = gpio_request_one(mtx1_wdt_device.gpio,
+ GPIOF_OUT_INIT_HIGH, "mtx1-wdt");
+ if (ret < 0) {
+ dev_err(&pdev->dev, "failed to request gpio");
+ return ret;
+ }
spin_lock_init(&mtx1_wdt_device.lock);
init_completion(&mtx1_wdt_device.stop);
mtx1_wdt_device.queue = 0;
wait_for_completion(&mtx1_wdt_device.stop);
}
+
+ gpio_free(mtx1_wdt_device.gpio);
misc_deregister(&mtx1_wdt_misc);
return 0;
}
-static struct platform_driver mtx1_wdt = {
+static struct platform_driver mtx1_wdt_driver = {
.probe = mtx1_wdt_probe,
.remove = __devexit_p(mtx1_wdt_remove),
.driver.name = "mtx1-wdt",
static int __init mtx1_wdt_init(void)
{
- return platform_driver_register(&mtx1_wdt);
+ return platform_driver_register(&mtx1_wdt_driver);
}
static void __exit mtx1_wdt_exit(void)
{
- platform_driver_unregister(&mtx1_wdt);
+ platform_driver_unregister(&mtx1_wdt_driver);
}
module_init(mtx1_wdt_init);
struct wm831x_watchdog_pdata *pdata;
int reg, ret;
+ if (wm831x) {
+ dev_err(&pdev->dev, "wm831x watchdog already registered\n");
+ return -EBUSY;
+ }
+
wm831x = dev_get_drvdata(pdev->dev.parent);
ret = wm831x_reg_read(wm831x, WM831X_WATCHDOG);
if (!disk)
return ERR_PTR(-ENXIO);
- whole = bdget_disk(disk, 0);
+ /*
+ * Normally, @bdev should equal what's returned from bdget_disk()
+ * if partno is 0; however, some drivers (floppy) use multiple
+ * bdev's for the same physical device and @bdev may be one of the
+ * aliases. Keep @bdev if partno is 0. This means claimer
+ * tracking is broken for those devices but it has always been that
+ * way.
+ */
+ if (partno)
+ whole = bdget_disk(disk, 0);
+ else
+ whole = bdgrab(bdev);
+
module_put(disk->fops->owner);
put_disk(disk);
if (!whole)
#ifndef __BTRFS_CTREE__
#define __BTRFS_CTREE__
-#include <linux/version.h>
#include <linux/mm.h>
#include <linux/highmem.h>
#include <linux/fs.h>
return root->fs_info->delayed_root;
}
-static struct btrfs_delayed_node *btrfs_get_or_create_delayed_node(
- struct inode *inode)
+static struct btrfs_delayed_node *btrfs_get_delayed_node(struct inode *inode)
{
- struct btrfs_delayed_node *node;
struct btrfs_inode *btrfs_inode = BTRFS_I(inode);
struct btrfs_root *root = btrfs_inode->root;
u64 ino = btrfs_ino(inode);
- int ret;
+ struct btrfs_delayed_node *node;
-again:
node = ACCESS_ONCE(btrfs_inode->delayed_node);
if (node) {
- atomic_inc(&node->refs); /* can be accessed */
+ atomic_inc(&node->refs);
return node;
}
node = radix_tree_lookup(&root->delayed_nodes_tree, ino);
if (node) {
if (btrfs_inode->delayed_node) {
+ atomic_inc(&node->refs); /* can be accessed */
+ BUG_ON(btrfs_inode->delayed_node != node);
spin_unlock(&root->inode_lock);
- goto again;
+ return node;
}
btrfs_inode->delayed_node = node;
atomic_inc(&node->refs); /* can be accessed */
}
spin_unlock(&root->inode_lock);
+ return NULL;
+}
+
+static struct btrfs_delayed_node *btrfs_get_or_create_delayed_node(
+ struct inode *inode)
+{
+ struct btrfs_delayed_node *node;
+ struct btrfs_inode *btrfs_inode = BTRFS_I(inode);
+ struct btrfs_root *root = btrfs_inode->root;
+ u64 ino = btrfs_ino(inode);
+ int ret;
+
+again:
+ node = btrfs_get_delayed_node(inode);
+ if (node)
+ return node;
+
node = kmem_cache_alloc(delayed_node_cache, GFP_NOFS);
if (!node)
return ERR_PTR(-ENOMEM);
return next;
}
-static inline struct btrfs_delayed_node *btrfs_get_delayed_node(
- struct inode *inode)
-{
- struct btrfs_inode *btrfs_inode = BTRFS_I(inode);
- struct btrfs_delayed_node *delayed_node;
-
- delayed_node = btrfs_inode->delayed_node;
- if (delayed_node)
- atomic_inc(&delayed_node->refs);
-
- return delayed_node;
-}
-
static inline struct btrfs_root *btrfs_get_fs_root(struct btrfs_root *root,
u64 root_id)
{
int btrfs_inode_delayed_dir_index_count(struct inode *inode)
{
- struct btrfs_delayed_node *delayed_node = BTRFS_I(inode)->delayed_node;
- int ret = 0;
+ struct btrfs_delayed_node *delayed_node = btrfs_get_delayed_node(inode);
if (!delayed_node)
return -ENOENT;
* a new directory index is added into the delayed node and index_cnt
* is updated now. So we needn't lock the delayed node.
*/
- if (!delayed_node->index_cnt)
+ if (!delayed_node->index_cnt) {
+ btrfs_release_delayed_node(delayed_node);
return -EINVAL;
+ }
BTRFS_I(inode)->index_cnt = delayed_node->index_cnt;
- return ret;
+ btrfs_release_delayed_node(delayed_node);
+ return 0;
}
void btrfs_get_delayed_items(struct inode *inode, struct list_head *ins_list,
inode->i_ctime.tv_nsec);
}
+int btrfs_fill_inode(struct inode *inode, u32 *rdev)
+{
+ struct btrfs_delayed_node *delayed_node;
+ struct btrfs_inode_item *inode_item;
+ struct btrfs_timespec *tspec;
+
+ delayed_node = btrfs_get_delayed_node(inode);
+ if (!delayed_node)
+ return -ENOENT;
+
+ mutex_lock(&delayed_node->mutex);
+ if (!delayed_node->inode_dirty) {
+ mutex_unlock(&delayed_node->mutex);
+ btrfs_release_delayed_node(delayed_node);
+ return -ENOENT;
+ }
+
+ inode_item = &delayed_node->inode_item;
+
+ inode->i_uid = btrfs_stack_inode_uid(inode_item);
+ inode->i_gid = btrfs_stack_inode_gid(inode_item);
+ btrfs_i_size_write(inode, btrfs_stack_inode_size(inode_item));
+ inode->i_mode = btrfs_stack_inode_mode(inode_item);
+ inode->i_nlink = btrfs_stack_inode_nlink(inode_item);
+ inode_set_bytes(inode, btrfs_stack_inode_nbytes(inode_item));
+ BTRFS_I(inode)->generation = btrfs_stack_inode_generation(inode_item);
+ BTRFS_I(inode)->sequence = btrfs_stack_inode_sequence(inode_item);
+ inode->i_rdev = 0;
+ *rdev = btrfs_stack_inode_rdev(inode_item);
+ BTRFS_I(inode)->flags = btrfs_stack_inode_flags(inode_item);
+
+ tspec = btrfs_inode_atime(inode_item);
+ inode->i_atime.tv_sec = btrfs_stack_timespec_sec(tspec);
+ inode->i_atime.tv_nsec = btrfs_stack_timespec_nsec(tspec);
+
+ tspec = btrfs_inode_mtime(inode_item);
+ inode->i_mtime.tv_sec = btrfs_stack_timespec_sec(tspec);
+ inode->i_mtime.tv_nsec = btrfs_stack_timespec_nsec(tspec);
+
+ tspec = btrfs_inode_ctime(inode_item);
+ inode->i_ctime.tv_sec = btrfs_stack_timespec_sec(tspec);
+ inode->i_ctime.tv_nsec = btrfs_stack_timespec_nsec(tspec);
+
+ inode->i_generation = BTRFS_I(inode)->generation;
+ BTRFS_I(inode)->index_cnt = (u64)-1;
+
+ mutex_unlock(&delayed_node->mutex);
+ btrfs_release_delayed_node(delayed_node);
+ return 0;
+}
+
int btrfs_delayed_update_inode(struct btrfs_trans_handle *trans,
struct btrfs_root *root, struct inode *inode)
{
int btrfs_delayed_update_inode(struct btrfs_trans_handle *trans,
struct btrfs_root *root, struct inode *inode);
+int btrfs_fill_inode(struct inode *inode, u32 *rdev);
/* Used for drop dead root */
void btrfs_kill_all_delayed_nodes(struct btrfs_root *root);
u64 num_bytes, u64 empty_size,
u64 search_start, u64 search_end,
u64 hint_byte, struct btrfs_key *ins,
- int data)
+ u64 data)
{
int ret = 0;
struct btrfs_root *root = orig_root->fs_info->extent_root;
space_info = __find_space_info(root->fs_info, data);
if (!space_info) {
- printk(KERN_ERR "No space info for %d\n", data);
+ printk(KERN_ERR "No space info for %llu\n", data);
return -ENOSPC;
}
while ((node = rb_last(&ctl->free_space_offset)) != NULL) {
info = rb_entry(node, struct btrfs_free_space, offset_index);
- unlink_free_space(ctl, info);
- kfree(info->bitmap);
- kmem_cache_free(btrfs_free_space_cachep, info);
+ if (!info->bitmap) {
+ unlink_free_space(ctl, info);
+ kmem_cache_free(btrfs_free_space_cachep, info);
+ } else {
+ free_bitmap(ctl, info);
+ }
if (need_resched()) {
spin_unlock(&ctl->tree_lock);
cond_resched();
int maybe_acls;
u32 rdev;
int ret;
+ bool filled = false;
+
+ ret = btrfs_fill_inode(inode, &rdev);
+ if (!ret)
+ filled = true;
path = btrfs_alloc_path();
BUG_ON(!path);
goto make_bad;
leaf = path->nodes[0];
+
+ if (filled)
+ goto cache_acl;
+
inode_item = btrfs_item_ptr(leaf, path->slots[0],
struct btrfs_inode_item);
if (!leaf->map_token)
BTRFS_I(inode)->index_cnt = (u64)-1;
BTRFS_I(inode)->flags = btrfs_inode_flags(leaf, inode_item);
-
+cache_acl:
/*
* try to precache a NULL acl entry for files that don't have
* any xattrs or acls
}
btrfs_free_path(path);
- inode_item = NULL;
switch (inode->i_mode & S_IFMT) {
case S_IFREG:
inode_tree_add(inode);
trace_btrfs_inode_new(inode);
+ btrfs_set_inode_last_trans(trans, inode);
return inode;
fail:
config CIFS_NFSD_EXPORT
bool "Allow nfsd to export CIFS file system (EXPERIMENTAL)"
- depends on CIFS && EXPERIMENTAL
+ depends on CIFS && EXPERIMENTAL && BROKEN
help
Allows NFS server to export a CIFS mounted share (nfsd over cifs)
#define CIFS_MOUNT_MULTIUSER 0x20000 /* multiuser mount */
#define CIFS_MOUNT_STRICT_IO 0x40000 /* strict cache mode */
#define CIFS_MOUNT_RWPIDFORWARD 0x80000 /* use pid forwarding for rw */
+#define CIFS_MOUNT_POSIXACL 0x100000 /* mirror of MS_POSIXACL in mnt_cifs_flags */
struct cifs_sb_info {
struct rb_root tlink_tree;
}
static int
-cifs_read_super(struct super_block *sb, struct smb_vol *volume_info,
- const char *devname, int silent)
+cifs_read_super(struct super_block *sb)
{
struct inode *inode;
struct cifs_sb_info *cifs_sb;
cifs_sb = CIFS_SB(sb);
- spin_lock_init(&cifs_sb->tlink_tree_lock);
- cifs_sb->tlink_tree = RB_ROOT;
+ if (cifs_sb->mnt_cifs_flags & CIFS_MOUNT_POSIXACL)
+ sb->s_flags |= MS_POSIXACL;
- rc = bdi_setup_and_register(&cifs_sb->bdi, "cifs", BDI_CAP_MAP_COPY);
- if (rc)
- return rc;
-
- cifs_sb->bdi.ra_pages = default_backing_dev_info.ra_pages;
+ if (cifs_sb_master_tcon(cifs_sb)->ses->capabilities & CAP_LARGE_FILES)
+ sb->s_maxbytes = MAX_LFS_FILESIZE;
+ else
+ sb->s_maxbytes = MAX_NON_LFS;
- rc = cifs_mount(sb, cifs_sb, volume_info, devname);
-
- if (rc) {
- if (!silent)
- cERROR(1, "cifs_mount failed w/return code = %d", rc);
- goto out_mount_failed;
- }
+ /* BB FIXME fix time_gran to be larger for LANMAN sessions */
+ sb->s_time_gran = 100;
sb->s_magic = CIFS_MAGIC_NUMBER;
sb->s_op = &cifs_super_ops;
if (inode)
iput(inode);
- cifs_umount(sb, cifs_sb);
-
-out_mount_failed:
- bdi_destroy(&cifs_sb->bdi);
return rc;
}
-static void
-cifs_put_super(struct super_block *sb)
+static void cifs_kill_sb(struct super_block *sb)
{
- int rc = 0;
- struct cifs_sb_info *cifs_sb;
-
- cFYI(1, "In cifs_put_super");
- cifs_sb = CIFS_SB(sb);
- if (cifs_sb == NULL) {
- cFYI(1, "Empty cifs superblock info passed to unmount");
- return;
- }
-
- rc = cifs_umount(sb, cifs_sb);
- if (rc)
- cERROR(1, "cifs_umount failed with return code %d", rc);
- if (cifs_sb->mountdata) {
- kfree(cifs_sb->mountdata);
- cifs_sb->mountdata = NULL;
- }
-
- unload_nls(cifs_sb->local_nls);
- bdi_destroy(&cifs_sb->bdi);
- kfree(cifs_sb);
+ struct cifs_sb_info *cifs_sb = CIFS_SB(sb);
+ kill_anon_super(sb);
+ cifs_umount(cifs_sb);
}
static int
}
static const struct super_operations cifs_super_ops = {
- .put_super = cifs_put_super,
.statfs = cifs_statfs,
.alloc_inode = cifs_alloc_inode,
.destroy_inode = cifs_destroy_inode,
full_path = cifs_build_path_to_root(vol, cifs_sb,
cifs_sb_master_tcon(cifs_sb));
if (full_path == NULL)
- return NULL;
+ return ERR_PTR(-ENOMEM);
cFYI(1, "Get root dentry for %s", full_path);
dchild = d_alloc(dparent, &name);
if (dchild == NULL) {
dput(dparent);
- dparent = NULL;
+ dparent = ERR_PTR(-ENOMEM);
goto out;
}
}
if (rc) {
dput(dchild);
dput(dparent);
- dparent = NULL;
+ dparent = ERR_PTR(rc);
goto out;
}
alias = d_materialise_unique(dchild, inode);
dput(dchild);
if (IS_ERR(alias)) {
dput(dparent);
- dparent = NULL;
+ dparent = ERR_PTR(-EINVAL); /* XXX */
goto out;
}
dchild = alias;
return dparent;
}
+static int cifs_set_super(struct super_block *sb, void *data)
+{
+ struct cifs_mnt_data *mnt_data = data;
+ sb->s_fs_info = mnt_data->cifs_sb;
+ return set_anon_super(sb, NULL);
+}
+
static struct dentry *
cifs_do_mount(struct file_system_type *fs_type,
int flags, const char *dev_name, void *data)
cifs_sb = kzalloc(sizeof(struct cifs_sb_info), GFP_KERNEL);
if (cifs_sb == NULL) {
root = ERR_PTR(-ENOMEM);
- goto out;
+ goto out_nls;
+ }
+
+ cifs_sb->mountdata = kstrndup(data, PAGE_SIZE, GFP_KERNEL);
+ if (cifs_sb->mountdata == NULL) {
+ root = ERR_PTR(-ENOMEM);
+ goto out_cifs_sb;
}
cifs_setup_cifs_sb(volume_info, cifs_sb);
+ rc = cifs_mount(cifs_sb, volume_info);
+ if (rc) {
+ if (!(flags & MS_SILENT))
+ cERROR(1, "cifs_mount failed w/return code = %d", rc);
+ root = ERR_PTR(rc);
+ goto out_mountdata;
+ }
+
mnt_data.vol = volume_info;
mnt_data.cifs_sb = cifs_sb;
mnt_data.flags = flags;
- sb = sget(fs_type, cifs_match_super, set_anon_super, &mnt_data);
+ sb = sget(fs_type, cifs_match_super, cifs_set_super, &mnt_data);
if (IS_ERR(sb)) {
root = ERR_CAST(sb);
- goto out_cifs_sb;
+ cifs_umount(cifs_sb);
+ goto out;
}
- if (sb->s_fs_info) {
+ if (sb->s_root) {
cFYI(1, "Use existing superblock");
- goto out_shared;
- }
-
- /*
- * Copy mount params for use in submounts. Better to do
- * the copy here and deal with the error before cleanup gets
- * complicated post-mount.
- */
- cifs_sb->mountdata = kstrndup(data, PAGE_SIZE, GFP_KERNEL);
- if (cifs_sb->mountdata == NULL) {
- root = ERR_PTR(-ENOMEM);
- goto out_super;
- }
-
- sb->s_flags = flags;
- /* BB should we make this contingent on mount parm? */
- sb->s_flags |= MS_NODIRATIME | MS_NOATIME;
- sb->s_fs_info = cifs_sb;
+ cifs_umount(cifs_sb);
+ } else {
+ sb->s_flags = flags;
+ /* BB should we make this contingent on mount parm? */
+ sb->s_flags |= MS_NODIRATIME | MS_NOATIME;
+
+ rc = cifs_read_super(sb);
+ if (rc) {
+ root = ERR_PTR(rc);
+ goto out_super;
+ }
- rc = cifs_read_super(sb, volume_info, dev_name,
- flags & MS_SILENT ? 1 : 0);
- if (rc) {
- root = ERR_PTR(rc);
- goto out_super;
+ sb->s_flags |= MS_ACTIVE;
}
- sb->s_flags |= MS_ACTIVE;
-
root = cifs_get_root(volume_info, sb);
- if (root == NULL)
+ if (IS_ERR(root))
goto out_super;
cFYI(1, "dentry root is: %p", root);
goto out;
-out_shared:
- root = cifs_get_root(volume_info, sb);
- if (root)
- cFYI(1, "dentry root is: %p", root);
- goto out;
-
out_super:
- kfree(cifs_sb->mountdata);
deactivate_locked_super(sb);
-
-out_cifs_sb:
- unload_nls(cifs_sb->local_nls);
- kfree(cifs_sb);
-
out:
cifs_cleanup_volume_info(&volume_info);
return root;
+
+out_mountdata:
+ kfree(cifs_sb->mountdata);
+out_cifs_sb:
+ kfree(cifs_sb);
+out_nls:
+ unload_nls(volume_info->local_nls);
+ goto out;
}
static ssize_t cifs_file_aio_write(struct kiocb *iocb, const struct iovec *iov,
.owner = THIS_MODULE,
.name = "cifs",
.mount = cifs_do_mount,
- .kill_sb = kill_anon_super,
+ .kill_sb = cifs_kill_sb,
/* .fs_flags */
};
const struct inode_operations cifs_dir_inode_ops = {
extern void cifs_cleanup_volume_info(struct smb_vol **pvolume_info);
extern int cifs_setup_volume_info(struct smb_vol **pvolume_info,
char *mount_data, const char *devname);
-extern int cifs_mount(struct super_block *, struct cifs_sb_info *,
- struct smb_vol *, const char *);
-extern int cifs_umount(struct super_block *, struct cifs_sb_info *);
+extern int cifs_mount(struct cifs_sb_info *, struct smb_vol *);
+extern void cifs_umount(struct cifs_sb_info *);
extern void cifs_dfs_release_automount_timer(void);
void cifs_proc_init(void);
void cifs_proc_clean(void);
struct dfs_info3_param **preferrals,
int remap);
extern void reset_cifs_unix_caps(int xid, struct cifs_tcon *tcon,
- struct super_block *sb, struct smb_vol *vol);
+ struct cifs_sb_info *cifs_sb,
+ struct smb_vol *vol);
extern int CIFSSMBQFSInfo(const int xid, struct cifs_tcon *tcon,
struct kstatfs *FSData);
extern int SMBOldQFSInfo(const int xid, struct cifs_tcon *tcon,
if (rc < 0)
return rc;
- rc = socket->ops->connect(socket, saddr, slen, 0);
- if (rc < 0) {
- cFYI(1, "Error %d connecting to server", rc);
- sock_release(socket);
- server->ssocket = NULL;
- return rc;
- }
-
/*
* Eventually check for other socket options to change from
* the default. sock_setsockopt not used because it expects
socket->sk->sk_sndbuf,
socket->sk->sk_rcvbuf, socket->sk->sk_rcvtimeo);
+ rc = socket->ops->connect(socket, saddr, slen, 0);
+ if (rc < 0) {
+ cFYI(1, "Error %d connecting to server", rc);
+ sock_release(socket);
+ server->ssocket = NULL;
+ return rc;
+ }
+
if (sport == htons(RFC1001_PORT))
rc = ip_rfc1001_connect(server);
}
void reset_cifs_unix_caps(int xid, struct cifs_tcon *tcon,
- struct super_block *sb, struct smb_vol *vol_info)
+ struct cifs_sb_info *cifs_sb, struct smb_vol *vol_info)
{
/* if we are reconnecting then should we check to see if
* any requested capabilities changed locally e.g. via
cap &= ~CIFS_UNIX_POSIX_ACL_CAP;
else if (CIFS_UNIX_POSIX_ACL_CAP & cap) {
cFYI(1, "negotiated posix acl support");
- if (sb)
- sb->s_flags |= MS_POSIXACL;
+ if (cifs_sb)
+ cifs_sb->mnt_cifs_flags |=
+ CIFS_MOUNT_POSIXACL;
}
if (vol_info && vol_info->posix_paths == 0)
cap &= ~CIFS_UNIX_POSIX_PATHNAMES_CAP;
else if (cap & CIFS_UNIX_POSIX_PATHNAMES_CAP) {
cFYI(1, "negotiate posix pathnames");
- if (sb)
- CIFS_SB(sb)->mnt_cifs_flags |=
+ if (cifs_sb)
+ cifs_sb->mnt_cifs_flags |=
CIFS_MOUNT_POSIX_PATHS;
}
- if (sb && (CIFS_SB(sb)->rsize > 127 * 1024)) {
+ if (cifs_sb && (cifs_sb->rsize > 127 * 1024)) {
if ((cap & CIFS_UNIX_LARGE_READ_CAP) == 0) {
- CIFS_SB(sb)->rsize = 127 * 1024;
+ cifs_sb->rsize = 127 * 1024;
cFYI(DBG2, "larger reads not supported by srv");
}
}
{
INIT_DELAYED_WORK(&cifs_sb->prune_tlinks, cifs_prune_tlinks);
+ spin_lock_init(&cifs_sb->tlink_tree_lock);
+ cifs_sb->tlink_tree = RB_ROOT;
+
if (pvolume_info->rsize > CIFSMaxBufSize) {
cERROR(1, "rsize %d too large, using MaxBufSize",
pvolume_info->rsize);
/*
* When the server supports very large writes via POSIX extensions, we can
- * allow up to 2^24 - PAGE_CACHE_SIZE.
+ * allow up to 2^24-1, minus the size of a WRITE_AND_X header, not including
+ * the RFC1001 length.
*
* Note that this might make for "interesting" allocation problems during
- * writeback however (as we have to allocate an array of pointers for the
- * pages). A 16M write means ~32kb page array with PAGE_CACHE_SIZE == 4096.
+ * writeback however as we have to allocate an array of pointers for the
+ * pages. A 16M write means ~32kb page array with PAGE_CACHE_SIZE == 4096.
*/
-#define CIFS_MAX_WSIZE ((1<<24) - PAGE_CACHE_SIZE)
+#define CIFS_MAX_WSIZE ((1<<24) - 1 - sizeof(WRITE_REQ) + 4)
/*
- * When the server doesn't allow large posix writes, default to a wsize of
- * 128k - PAGE_CACHE_SIZE -- one page less than the largest frame size
- * described in RFC1001. This allows space for the header without going over
- * that by default.
+ * When the server doesn't allow large posix writes, only allow a wsize of
+ * 128k minus the size of the WRITE_AND_X header. That allows for a write up
+ * to the maximum size described by RFC1002.
*/
-#define CIFS_MAX_RFC1001_WSIZE (128 * 1024 - PAGE_CACHE_SIZE)
+#define CIFS_MAX_RFC1002_WSIZE (128 * 1024 - sizeof(WRITE_REQ) + 4)
/*
* The default wsize is 1M. find_get_pages seems to return a maximum of 256
/* can server support 24-bit write sizes? (via UNIX extensions) */
if (!tcon->unix_ext || !(unix_cap & CIFS_UNIX_LARGE_WRITE_CAP))
- wsize = min_t(unsigned int, wsize, CIFS_MAX_RFC1001_WSIZE);
+ wsize = min_t(unsigned int, wsize, CIFS_MAX_RFC1002_WSIZE);
- /* no CAP_LARGE_WRITE_X? Limit it to 16 bits */
- if (!(server->capabilities & CAP_LARGE_WRITE_X))
- wsize = min_t(unsigned int, wsize, USHRT_MAX);
+ /*
+ * no CAP_LARGE_WRITE_X or is signing enabled without CAP_UNIX set?
+ * Limit it to max buffer offered by the server, minus the size of the
+ * WRITEX header, not including the 4 byte RFC1001 length.
+ */
+ if (!(server->capabilities & CAP_LARGE_WRITE_X) ||
+ (!(server->capabilities & CAP_UNIX) &&
+ (server->sec_mode & (SECMODE_SIGN_ENABLED|SECMODE_SIGN_REQUIRED))))
+ wsize = min_t(unsigned int, wsize,
+ server->maxBuf - sizeof(WRITE_REQ) + 4);
/* hard limit of CIFS_MAX_WSIZE */
wsize = min_t(unsigned int, wsize, CIFS_MAX_WSIZE);
if (volume_info->nullauth) {
cFYI(1, "null user");
- volume_info->username = "";
+ volume_info->username = kzalloc(1, GFP_KERNEL);
+ if (volume_info->username == NULL) {
+ rc = -ENOMEM;
+ goto out;
+ }
} else if (volume_info->username) {
/* BB fixme parse for domain name here */
cFYI(1, "Username: %s", volume_info->username);
}
int
-cifs_mount(struct super_block *sb, struct cifs_sb_info *cifs_sb,
- struct smb_vol *volume_info, const char *devname)
+cifs_mount(struct cifs_sb_info *cifs_sb, struct smb_vol *volume_info)
{
int rc = 0;
int xid;
struct tcon_link *tlink;
#ifdef CONFIG_CIFS_DFS_UPCALL
int referral_walks_count = 0;
+
+ rc = bdi_setup_and_register(&cifs_sb->bdi, "cifs", BDI_CAP_MAP_COPY);
+ if (rc)
+ return rc;
+
+ cifs_sb->bdi.ra_pages = default_backing_dev_info.ra_pages;
+
try_mount_again:
/* cleanup activities if we're chasing a referral */
if (referral_walks_count) {
srvTcp = cifs_get_tcp_session(volume_info);
if (IS_ERR(srvTcp)) {
rc = PTR_ERR(srvTcp);
+ bdi_destroy(&cifs_sb->bdi);
goto out;
}
goto mount_fail_check;
}
- if (pSesInfo->capabilities & CAP_LARGE_FILES)
- sb->s_maxbytes = MAX_LFS_FILESIZE;
- else
- sb->s_maxbytes = MAX_NON_LFS;
-
- /* BB FIXME fix time_gran to be larger for LANMAN sessions */
- sb->s_time_gran = 100;
-
/* search for existing tcon to this server share */
tcon = cifs_get_tcon(pSesInfo, volume_info);
if (IS_ERR(tcon)) {
if (tcon->ses->capabilities & CAP_UNIX) {
/* reset of caps checks mount to see if unix extensions
disabled for just this mount */
- reset_cifs_unix_caps(xid, tcon, sb, volume_info);
+ reset_cifs_unix_caps(xid, tcon, cifs_sb, volume_info);
if ((tcon->ses->server->tcpStatus == CifsNeedReconnect) &&
(le64_to_cpu(tcon->fsUnixInfo.Capability) &
CIFS_UNIX_TRANSPORT_ENCRYPTION_MANDATORY_CAP)) {
cifs_put_smb_ses(pSesInfo);
else
cifs_put_tcp_session(srvTcp);
+ bdi_destroy(&cifs_sb->bdi);
goto out;
}
return rc;
}
-int
-cifs_umount(struct super_block *sb, struct cifs_sb_info *cifs_sb)
+void
+cifs_umount(struct cifs_sb_info *cifs_sb)
{
struct rb_root *root = &cifs_sb->tlink_tree;
struct rb_node *node;
}
spin_unlock(&cifs_sb->tlink_tree_lock);
- return 0;
+ bdi_destroy(&cifs_sb->bdi);
+ kfree(cifs_sb->mountdata);
+ unload_nls(cifs_sb->local_nls);
+ kfree(cifs_sb);
}
int cifs_negotiate_protocol(unsigned int xid, struct cifs_ses *ses)
sg_init_one(&sgout, out, 8);
rc = crypto_blkcipher_encrypt(&desc, &sgout, &sgin, 8);
- if (rc) {
+ if (rc)
cERROR(1, "could not encrypt crypt key rc: %d\n", rc);
- crypto_free_blkcipher(tfm_des);
- goto smbhash_err;
- }
+ crypto_free_blkcipher(tfm_des);
smbhash_err:
return rc;
}
void end_writeback(struct inode *inode)
{
might_sleep();
+ /*
+ * We have to cycle tree_lock here because reclaim can be still in the
+ * process of removing the last page (in __delete_from_page_cache())
+ * and we must not free mapping under it.
+ */
+ spin_lock_irq(&inode->i_data.tree_lock);
BUG_ON(inode->i_data.nrpages);
+ spin_unlock_irq(&inode->i_data.tree_lock);
BUG_ON(!list_empty(&inode->i_data.private_list));
BUG_ON(!(inode->i_state & I_FREEING));
BUG_ON(inode->i_state & I_CLEAR);
* Released under GPL v2.
*/
-#include <linux/version.h>
#include <linux/module.h>
#include <linux/fs.h>
#include <linux/buffer_head.h>
struct task_io_accounting acct = task->ioac;
unsigned long flags;
+ if (!ptrace_may_access(task, PTRACE_MODE_READ))
+ return -EACCES;
+
if (whole && lock_task_sighand(task, &flags)) {
struct task_struct *t = task;
REG("coredump_filter", S_IRUGO|S_IWUSR, proc_coredump_filter_operations),
#endif
#ifdef CONFIG_TASK_IO_ACCOUNTING
- INF("io", S_IRUGO, proc_tgid_io_accounting),
+ INF("io", S_IRUSR, proc_tgid_io_accounting),
#endif
#ifdef CONFIG_HARDWALL
INF("hardwall", S_IRUGO, proc_pid_hardwall),
REG("make-it-fail", S_IRUGO|S_IWUSR, proc_fault_inject_operations),
#endif
#ifdef CONFIG_TASK_IO_ACCOUNTING
- INF("io", S_IRUGO, proc_tid_io_accounting),
+ INF("io", S_IRUSR, proc_tid_io_accounting),
#endif
#ifdef CONFIG_HARDWALL
INF("hardwall", S_IRUGO, proc_pid_hardwall),
{
struct inode *inode = file->f_mapping->host;
struct mtd_info *mtd = inode->i_sb->s_mtd;
- unsigned long isize, offset;
+ unsigned long isize, offset, maxpages, lpages;
if (!mtd)
goto cant_map_directly;
+ /* the mapping mustn't extend beyond the EOF */
+ lpages = (len + PAGE_SIZE - 1) >> PAGE_SHIFT;
isize = i_size_read(inode);
offset = pgoff << PAGE_SHIFT;
- if (offset > isize || len > isize || offset > isize - len)
+
+ maxpages = (isize + PAGE_SIZE - 1) >> PAGE_SHIFT;
+ if ((pgoff >= maxpages) || (maxpages - pgoff < lpages))
return (unsigned long) -EINVAL;
/* we need to call down to the MTD layer to do the actual mapping */
args.whichfork = XFS_ATTR_FORK;
/*
+ * we have no control over the attribute names that userspace passes us
+ * to remove, so we have to allow the name lookup prior to attribute
+ * removal to fail.
+ */
+ args.op_flags = XFS_DA_OP_OKNOENT;
+
+ /*
* Attach the dquots to the inode.
*/
error = xfs_qm_dqattach(dp, 0);
rcu_read_lock();
spin_lock(&ip->i_flags_lock);
- ip->i_flags &= ~XFS_INEW;
- ip->i_flags |= XFS_IRECLAIMABLE;
- __xfs_inode_set_reclaim_tag(pag, ip);
+ ip->i_flags &= ~(XFS_INEW | XFS_IRECLAIM);
+ ASSERT(ip->i_flags & XFS_IRECLAIMABLE);
trace_xfs_iget_reclaim_fail(ip);
goto out_error;
}
spin_lock(&pag->pag_ici_lock);
spin_lock(&ip->i_flags_lock);
- ip->i_flags &= ~(XFS_IRECLAIMABLE | XFS_IRECLAIM);
+
+ /*
+ * Clear the per-lifetime state in the inode as we are now
+ * effectively a new inode and need to return to the initial
+ * state before reuse occurs.
+ */
+ ip->i_flags &= ~XFS_IRECLAIM_RESET_FLAGS;
ip->i_flags |= XFS_INEW;
__xfs_inode_clear_reclaim_tag(mp, pag, ip);
inode->i_state = I_NEW;
#define XFS_IDIRTY_RELEASE 0x0040 /* dirty release already seen */
/*
+ * Per-lifetime flags need to be reset when re-using a reclaimable inode during
+ * inode lookup. Thi prevents unintended behaviour on the new inode from
+ * ocurring.
+ */
+#define XFS_IRECLAIM_RESET_FLAGS \
+ (XFS_IRECLAIMABLE | XFS_IRECLAIM | \
+ XFS_IDIRTY_RELEASE | XFS_ITRUNCATED | \
+ XFS_IFILESTREAM);
+
+/*
* Flags for inode locking.
* Bit ranges: 1<<1 - 1<<16-1 -- iolock/ilock modes (bitfield)
* 1<<16 - 1<<32-1 -- lockdep annotation (integers)
* be exposed to that problem.
*/
truncated = xfs_iflags_test_and_clear(ip, XFS_ITRUNCATED);
- if (truncated && VN_DIRTY(VFS_I(ip)) && ip->i_delayed_blks > 0)
- xfs_flush_pages(ip, 0, -1, XBF_ASYNC, FI_NONE);
+ if (truncated) {
+ xfs_iflags_clear(ip, XFS_IDIRTY_RELEASE);
+ if (VN_DIRTY(VFS_I(ip)) && ip->i_delayed_blks > 0)
+ xfs_flush_pages(ip, 0, -1, XBF_ASYNC, FI_NONE);
+ }
}
if (ip->i_d.di_nlink == 0)
bool (*dma_filter)(struct dma_chan *chan, void *filter_param);
void *dma_rx_param;
void *dma_tx_param;
+ void (*init) (void);
+ void (*exit) (void);
+ void (*reset) (void);
};
#endif
(REQ_FAILFAST_DEV | REQ_FAILFAST_TRANSPORT | REQ_FAILFAST_DRIVER)
#define REQ_COMMON_MASK \
(REQ_WRITE | REQ_FAILFAST_MASK | REQ_SYNC | REQ_META | REQ_DISCARD | \
- REQ_NOIDLE | REQ_FLUSH | REQ_FUA)
+ REQ_NOIDLE | REQ_FLUSH | REQ_FUA | REQ_SECURE)
#define REQ_CLONE_MASK REQ_COMMON_MASK
#define REQ_RAHEAD (1 << __REQ_RAHEAD)
extern int do_blk_trace_setup(struct request_queue *q, char *name,
dev_t dev, struct block_device *bdev,
struct blk_user_trace_setup *buts);
-extern void __trace_note_message(struct blk_trace *, const char *fmt, ...);
+extern __attribute__((format(printf, 2, 3)))
+void __trace_note_message(struct blk_trace *, const char *fmt, ...);
/**
* blk_add_trace_msg - Add a (simple) message to the blktrace stream
char __user *optval, unsigned int optlen);
asmlinkage long compat_sys_sendmsg(int fd, struct compat_msghdr __user *msg,
unsigned flags);
+asmlinkage long compat_sys_sendmmsg(int fd, struct compat_mmsghdr __user *mmsg,
+ unsigned vlen, unsigned int flags);
asmlinkage long compat_sys_recvmsg(int fd, struct compat_msghdr __user *msg,
unsigned int flags);
asmlinkage long compat_sys_recv(int fd, void __user *buf, size_t len,
#define CN_VAL_DRBD 0x1
#define CN_KVP_IDX 0x9 /* HyperV KVP */
-#define CN_NETLINK_USERS 9
+#define CN_NETLINK_USERS 10 /* Highest index + 1 */
/*
* Maximum connector's message size.
* @dma_mem: Internal for coherent mem override.
* @archdata: For arch-specific additions.
* @of_node: Associated device tree node.
- * @of_match: Matching of_device_id from driver.
* @devt: For creating the sysfs "dev".
* @devres_lock: Spinlock to protect the resource of the device.
* @devres_head: The resources list of the device.
struct prio_tree_root i_mmap; /* tree of private and shared mappings */
struct list_head i_mmap_nonlinear;/*list VM_NONLINEAR mappings */
struct mutex i_mmap_mutex; /* protect tree, count, list */
+ /* Protected by tree_lock together with the radix tree */
unsigned long nrpages; /* number of total pages */
pgoff_t writeback_index;/* writeback starts here */
const struct address_space_operations *a_ops; /* methods */
* @cpu_base: per cpu clock base
* @index: clock type index for per_cpu support when moving a
* timer to a base on another cpu.
+ * @clockid: clock id for per_cpu support
* @active: red black tree root node for the active timers
* @resolution: the resolution of the clock, in nanoseconds
* @get_time: function to retrieve the current time of the clock
#endif
#define nid_page_nr(nid, pagenr) pgdat_page_nr(NODE_DATA(nid),(pagenr))
+#define node_start_pfn(nid) (NODE_DATA(nid)->node_start_pfn)
+
+#define node_end_pfn(nid) ({\
+ pg_data_t *__pgdat = NODE_DATA(nid);\
+ __pgdat->node_start_pfn + __pgdat->node_spanned_pages;\
+})
+
#include <linux/memory_hotplug.h>
extern struct mutex zonelists_mutex;
#define PCI_DEVICE_ID_RICOH_RL5C476 0x0476
#define PCI_DEVICE_ID_RICOH_RL5C478 0x0478
#define PCI_DEVICE_ID_RICOH_R5C822 0x0822
+#define PCI_DEVICE_ID_RICOH_R5CE823 0xe823
#define PCI_DEVICE_ID_RICOH_R5C832 0x0832
#define PCI_DEVICE_ID_RICOH_R5C843 0x0843
#include <linux/swap.h>
#include <linux/mempolicy.h>
+#include <linux/pagemap.h>
#include <linux/percpu_counter.h>
/* inode in-kernel data */
return container_of(inode, struct shmem_inode_info, vfs_inode);
}
+/*
+ * Functions in mm/shmem.c called directly from elsewhere:
+ */
extern int init_tmpfs(void);
extern int shmem_fill_super(struct super_block *sb, void *data, int silent);
+extern struct file *shmem_file_setup(const char *name,
+ loff_t size, unsigned long flags);
+extern int shmem_zero_setup(struct vm_area_struct *);
+extern int shmem_lock(struct file *file, int lock, struct user_struct *user);
+extern struct page *shmem_read_mapping_page_gfp(struct address_space *mapping,
+ pgoff_t index, gfp_t gfp_mask);
+extern void shmem_truncate_range(struct inode *inode, loff_t start, loff_t end);
+extern int shmem_unuse(swp_entry_t entry, struct page *page);
+extern void mem_cgroup_get_shmem_target(struct inode *inode, pgoff_t pgoff,
+ struct page **pagep, swp_entry_t *ent);
+
+static inline struct page *shmem_read_mapping_page(
+ struct address_space *mapping, pgoff_t index)
+{
+ return shmem_read_mapping_page_gfp(mapping, index,
+ mapping_gfp_mask(mapping));
+}
#endif
extern int kswapd_run(int nid);
extern void kswapd_stop(int nid);
-#ifdef CONFIG_MMU
-/* linux/mm/shmem.c */
-extern int shmem_unuse(swp_entry_t entry, struct page *page);
-#endif /* CONFIG_MMU */
-
-#ifdef CONFIG_CGROUP_MEM_RES_CTLR
-extern void mem_cgroup_get_shmem_target(struct inode *inode, pgoff_t pgoff,
- struct page **pagep, swp_entry_t *ent);
-#endif
-
#ifdef CONFIG_SWAP
/* linux/mm/page_io.c */
extern int swap_readpage(struct page *);
* @sk_dst_cache: destination cache
* @sk_dst_lock: destination cache lock
* @sk_policy: flow policy
- * @sk_rmem_alloc: receive queue bytes committed
* @sk_receive_queue: incoming packets
* @sk_wmem_alloc: transmit queue bytes committed
* @sk_write_queue: Packet sending queue
/* get CSP information */
#define SNDRV_SB_CSP_IOCTL_INFO _IOR('H', 0x10, struct snd_sb_csp_info)
/* load microcode to CSP */
-#define SNDRV_SB_CSP_IOCTL_LOAD_CODE _IOW('H', 0x11, struct snd_sb_csp_microcode)
+/* NOTE: struct snd_sb_csp_microcode overflows the max size (13 bits)
+ * defined for some architectures like MIPS, and it leads to build errors.
+ * (x86 and co have 14-bit size, thus it's valid, though.)
+ * As a workaround for skipping the size-limit check, here we don't use the
+ * normal _IOW() macro but _IOC() with the manual argument.
+ */
+#define SNDRV_SB_CSP_IOCTL_LOAD_CODE \
+ _IOC(_IOC_WRITE, 'H', 0x11, sizeof(struct snd_sb_csp_microcode))
/* unload microcode from CSP */
#define SNDRV_SB_CSP_IOCTL_UNLOAD_CODE _IO('H', 0x12)
/* start CSP */
extern struct snd_ac97_bus_ops soc_ac97_ops;
enum snd_soc_control_type {
- SND_SOC_CUSTOM = 1,
- SND_SOC_I2C,
+ SND_SOC_I2C = 1,
SND_SOC_SPI,
};
void __cpuinit calibrate_delay(void)
{
+ unsigned long lpj;
static bool printed;
if (preset_lpj) {
- loops_per_jiffy = preset_lpj;
+ lpj = preset_lpj;
if (!printed)
pr_info("Calibrating delay loop (skipped) "
"preset value.. ");
} else if ((!printed) && lpj_fine) {
- loops_per_jiffy = lpj_fine;
+ lpj = lpj_fine;
pr_info("Calibrating delay loop (skipped), "
"value calculated using timer frequency.. ");
- } else if ((loops_per_jiffy = calibrate_delay_direct()) != 0) {
+ } else if ((lpj = calibrate_delay_direct()) != 0) {
if (!printed)
pr_info("Calibrating delay using timer "
"specific routine.. ");
} else {
if (!printed)
pr_info("Calibrating delay loop... ");
- loops_per_jiffy = calibrate_delay_converge();
+ lpj = calibrate_delay_converge();
}
if (!printed)
pr_cont("%lu.%02lu BogoMIPS (lpj=%lu)\n",
- loops_per_jiffy/(500000/HZ),
- (loops_per_jiffy/(5000/HZ)) % 100, loops_per_jiffy);
+ lpj/(500000/HZ),
+ (lpj/(5000/HZ)) % 100, lpj);
+ loops_per_jiffy = lpj;
printed = true;
}
static int add_del_listener(pid_t pid, const struct cpumask *mask, int isadd)
{
struct listener_list *listeners;
- struct listener *s, *tmp;
+ struct listener *s, *tmp, *s2;
unsigned int cpu;
if (!cpumask_subset(mask, cpu_possible_mask))
return -EINVAL;
+ s = NULL;
if (isadd == REGISTER) {
for_each_cpu(cpu, mask) {
- s = kmalloc_node(sizeof(struct listener), GFP_KERNEL,
- cpu_to_node(cpu));
+ if (!s)
+ s = kmalloc_node(sizeof(struct listener),
+ GFP_KERNEL, cpu_to_node(cpu));
if (!s)
goto cleanup;
s->pid = pid;
listeners = &per_cpu(listener_array, cpu);
down_write(&listeners->sem);
+ list_for_each_entry_safe(s2, tmp, &listeners->list, list) {
+ if (s2->pid == pid)
+ goto next_cpu;
+ }
list_add(&s->list, &listeners->list);
+ s = NULL;
+next_cpu:
up_write(&listeners->sem);
}
+ kfree(s);
return 0;
}
clockid_t base_clockid;
} alarm_bases[ALARM_NUMTYPE];
+/* freezer delta & lock used to handle clock_nanosleep triggered wakeups */
+static ktime_t freezer_delta;
+static DEFINE_SPINLOCK(freezer_delta_lock);
+
#ifdef CONFIG_RTC_CLASS
/* rtc timer and device for setting alarm wakeups at suspend */
static struct rtc_timer rtctimer;
static struct rtc_device *rtcdev;
-#endif
+static DEFINE_SPINLOCK(rtcdev_lock);
-/* freezer delta & lock used to handle clock_nanosleep triggered wakeups */
-static ktime_t freezer_delta;
-static DEFINE_SPINLOCK(freezer_delta_lock);
+/**
+ * has_wakealarm - check rtc device has wakealarm ability
+ * @dev: current device
+ * @name_ptr: name to be returned
+ *
+ * This helper function checks to see if the rtc device can wake
+ * from suspend.
+ */
+static int has_wakealarm(struct device *dev, void *name_ptr)
+{
+ struct rtc_device *candidate = to_rtc_device(dev);
+
+ if (!candidate->ops->set_alarm)
+ return 0;
+ if (!device_may_wakeup(candidate->dev.parent))
+ return 0;
+
+ *(const char **)name_ptr = dev_name(dev);
+ return 1;
+}
+
+/**
+ * alarmtimer_get_rtcdev - Return selected rtcdevice
+ *
+ * This function returns the rtc device to use for wakealarms.
+ * If one has not already been chosen, it checks to see if a
+ * functional rtc device is available.
+ */
+static struct rtc_device *alarmtimer_get_rtcdev(void)
+{
+ struct device *dev;
+ char *str;
+ unsigned long flags;
+ struct rtc_device *ret;
+
+ spin_lock_irqsave(&rtcdev_lock, flags);
+ if (!rtcdev) {
+ /* Find an rtc device and init the rtc_timer */
+ dev = class_find_device(rtc_class, NULL, &str, has_wakealarm);
+ /* If we have a device then str is valid. See has_wakealarm() */
+ if (dev) {
+ rtcdev = rtc_class_open(str);
+ /*
+ * Drop the reference we got in class_find_device,
+ * rtc_open takes its own.
+ */
+ put_device(dev);
+ rtc_timer_init(&rtctimer, NULL, NULL);
+ }
+ }
+ ret = rtcdev;
+ spin_unlock_irqrestore(&rtcdev_lock, flags);
+
+ return ret;
+}
+#else
+#define alarmtimer_get_rtcdev() (0)
+#define rtcdev (0)
+#endif
/**
struct rtc_time tm;
ktime_t min, now;
unsigned long flags;
+ struct rtc_device *rtc;
int i;
spin_lock_irqsave(&freezer_delta_lock, flags);
freezer_delta = ktime_set(0, 0);
spin_unlock_irqrestore(&freezer_delta_lock, flags);
+ rtc = rtcdev;
/* If we have no rtcdev, just return */
- if (!rtcdev)
+ if (!rtc)
return 0;
/* Find the soonest timer to expire*/
WARN_ON(min.tv64 < NSEC_PER_SEC);
/* Setup an rtc timer to fire that far in the future */
- rtc_timer_cancel(rtcdev, &rtctimer);
- rtc_read_time(rtcdev, &tm);
+ rtc_timer_cancel(rtc, &rtctimer);
+ rtc_read_time(rtc, &tm);
now = rtc_tm_to_ktime(tm);
now = ktime_add(now, min);
- rtc_timer_start(rtcdev, &rtctimer, now, ktime_set(0, 0));
+ rtc_timer_start(rtc, &rtctimer, now, ktime_set(0, 0));
return 0;
}
{
clockid_t baseid = alarm_bases[clock2alarm(which_clock)].base_clockid;
+ if (!alarmtimer_get_rtcdev())
+ return -ENOTSUPP;
+
return hrtimer_get_res(baseid, tp);
}
{
struct alarm_base *base = &alarm_bases[clock2alarm(which_clock)];
+ if (!alarmtimer_get_rtcdev())
+ return -ENOTSUPP;
+
*tp = ktime_to_timespec(base->gettime());
return 0;
}
enum alarmtimer_type type;
struct alarm_base *base;
+ if (!alarmtimer_get_rtcdev())
+ return -ENOTSUPP;
+
if (!capable(CAP_WAKE_ALARM))
return -EPERM;
*/
static int alarm_timer_del(struct k_itimer *timr)
{
+ if (!rtcdev)
+ return -ENOTSUPP;
+
alarm_cancel(&timr->it.alarmtimer);
return 0;
}
struct itimerspec *new_setting,
struct itimerspec *old_setting)
{
+ if (!rtcdev)
+ return -ENOTSUPP;
+
/* Save old values */
old_setting->it_interval =
ktime_to_timespec(timr->it.alarmtimer.period);
int ret = 0;
struct restart_block *restart;
+ if (!alarmtimer_get_rtcdev())
+ return -ENOTSUPP;
+
if (!capable(CAP_WAKE_ALARM))
return -EPERM;
}
device_initcall(alarmtimer_init);
-#ifdef CONFIG_RTC_CLASS
-/**
- * has_wakealarm - check rtc device has wakealarm ability
- * @dev: current device
- * @name_ptr: name to be returned
- *
- * This helper function checks to see if the rtc device can wake
- * from suspend.
- */
-static int __init has_wakealarm(struct device *dev, void *name_ptr)
-{
- struct rtc_device *candidate = to_rtc_device(dev);
-
- if (!candidate->ops->set_alarm)
- return 0;
- if (!device_may_wakeup(candidate->dev.parent))
- return 0;
-
- *(const char **)name_ptr = dev_name(dev);
- return 1;
-}
-
-/**
- * alarmtimer_init_late - Late initializing of alarmtimer code
- *
- * This function locates a rtc device to use for wakealarms.
- * Run as late_initcall to make sure rtc devices have been
- * registered.
- */
-static int __init alarmtimer_init_late(void)
-{
- struct device *dev;
- char *str;
-
- /* Find an rtc device and init the rtc_timer */
- dev = class_find_device(rtc_class, NULL, &str, has_wakealarm);
- /* If we have a device then str is valid. See has_wakealarm() */
- if (dev) {
- rtcdev = rtc_class_open(str);
- /*
- * Drop the reference we got in class_find_device,
- * rtc_open takes its own.
- */
- put_device(dev);
- }
- if (!rtcdev) {
- printk(KERN_WARNING "No RTC device found, ALARM timers will"
- " not wake from suspend");
- }
- rtc_timer_init(&rtctimer, NULL, NULL);
-
- return 0;
-}
-#else
-static int __init alarmtimer_init_late(void)
-{
- printk(KERN_WARNING "Kernel not built with RTC support, ALARM timers"
- " will not wake from suspend");
- return 0;
-}
-#endif
-late_initcall(alarmtimer_init_late);
#include <linux/limits.h>
#include <linux/mutex.h>
#include <linux/rbtree.h>
+#include <linux/shmem_fs.h>
#include <linux/slab.h>
#include <linux/swap.h>
#include <linux/swapops.h>
struct task_struct *tsk;
struct anon_vma *av;
- read_lock(&tasklist_lock);
av = page_lock_anon_vma(page);
if (av == NULL) /* Not actually mapped anymore */
- goto out;
+ return;
+
+ read_lock(&tasklist_lock);
for_each_process (tsk) {
struct anon_vma_chain *vmac;
add_to_kill(tsk, page, vma, to_kill, tkc);
}
}
- page_unlock_anon_vma(av);
-out:
read_unlock(&tasklist_lock);
+ page_unlock_anon_vma(av);
}
/*
struct prio_tree_iter iter;
struct address_space *mapping = page->mapping;
- /*
- * A note on the locking order between the two locks.
- * We don't rely on this particular order.
- * If you have some other code that needs a different order
- * feel free to switch them around. Or add a reverse link
- * from mm_struct to task_struct, then this could be all
- * done without taking tasklist_lock and looping over all tasks.
- */
-
- read_lock(&tasklist_lock);
mutex_lock(&mapping->i_mmap_mutex);
+ read_lock(&tasklist_lock);
for_each_process(tsk) {
pgoff_t pgoff = page->index << (PAGE_CACHE_SHIFT - PAGE_SHIFT);
add_to_kill(tsk, page, vma, to_kill, tkc);
}
}
- mutex_unlock(&mapping->i_mmap_mutex);
read_unlock(&tasklist_lock);
+ mutex_unlock(&mapping->i_mmap_mutex);
}
/*
}
EXPORT_SYMBOL(unmap_mapping_range);
-int vmtruncate_range(struct inode *inode, loff_t offset, loff_t end)
-{
- struct address_space *mapping = inode->i_mapping;
-
- /*
- * If the underlying filesystem is not going to provide
- * a way to truncate a range of blocks (punch a hole) -
- * we should return failure right now.
- */
- if (!inode->i_op->truncate_range)
- return -ENOSYS;
-
- mutex_lock(&inode->i_mutex);
- down_write(&inode->i_alloc_sem);
- unmap_mapping_range(mapping, offset, (end - offset), 1);
- truncate_inode_pages_range(mapping, offset, end);
- unmap_mapping_range(mapping, offset, (end - offset), 1);
- inode->i_op->truncate_range(inode, offset, end);
- up_write(&inode->i_alloc_sem);
- mutex_unlock(&inode->i_mutex);
-
- return 0;
-}
-
/*
* We enter with non-exclusive mmap_sem (to exclude vma changes,
* but allow concurrent faults), and pte mapped but not yet locked.
* in arch-dependent flush_dcache_mmap_lock,
* within inode_wb_list_lock in __sync_single_inode)
*
- * (code doesn't rely on that order so it could be switched around)
- * ->tasklist_lock
- * anon_vma->mutex (memory_failure, collect_procs_anon)
+ * anon_vma->mutex,mapping->i_mutex (memory_failure, collect_procs_anon)
+ * ->tasklist_lock
* pte map lock
*/
} while (next);
}
-static void shmem_truncate_range(struct inode *inode, loff_t start, loff_t end)
+void shmem_truncate_range(struct inode *inode, loff_t start, loff_t end)
{
struct shmem_inode_info *info = SHMEM_I(inode);
unsigned long idx;
spinlock_t *punch_lock;
unsigned long upper_limit;
+ truncate_inode_pages_range(inode->i_mapping, start, end);
+
inode->i_ctime = inode->i_mtime = CURRENT_TIME;
idx = (start + PAGE_CACHE_SIZE - 1) >> PAGE_CACHE_SHIFT;
if (idx >= info->next_index)
* lowered next_index. Also, though shmem_getpage checks
* i_size before adding to cache, no recheck after: so fix the
* narrow window there too.
- *
- * Recalling truncate_inode_pages_range and unmap_mapping_range
- * every time for punch_hole (which never got a chance to clear
- * SHMEM_PAGEIN at the start of vmtruncate_range) is expensive,
- * yet hardly ever necessary: try to optimize them out later.
*/
truncate_inode_pages_range(inode->i_mapping, start, end);
- if (punch_hole)
- unmap_mapping_range(inode->i_mapping, start,
- end - start, 1);
}
spin_lock(&info->lock);
shmem_free_pages(pages_to_free.next);
}
}
+EXPORT_SYMBOL_GPL(shmem_truncate_range);
-static int shmem_notify_change(struct dentry *dentry, struct iattr *attr)
+static int shmem_setattr(struct dentry *dentry, struct iattr *attr)
{
struct inode *inode = dentry->d_inode;
- loff_t newsize = attr->ia_size;
int error;
error = inode_change_ok(inode, attr);
if (error)
return error;
- if (S_ISREG(inode->i_mode) && (attr->ia_valid & ATTR_SIZE)
- && newsize != inode->i_size) {
+ if (S_ISREG(inode->i_mode) && (attr->ia_valid & ATTR_SIZE)) {
+ loff_t oldsize = inode->i_size;
+ loff_t newsize = attr->ia_size;
struct page *page = NULL;
- if (newsize < inode->i_size) {
+ if (newsize < oldsize) {
/*
* If truncating down to a partial page, then
* if that page is already allocated, hold it
spin_unlock(&info->lock);
}
}
-
- /* XXX(truncate): truncate_setsize should be called last */
- truncate_setsize(inode, newsize);
+ if (newsize != oldsize) {
+ i_size_write(inode, newsize);
+ inode->i_ctime = inode->i_mtime = CURRENT_TIME;
+ }
+ if (newsize < oldsize) {
+ loff_t holebegin = round_up(newsize, PAGE_SIZE);
+ unmap_mapping_range(inode->i_mapping, holebegin, 0, 1);
+ shmem_truncate_range(inode, newsize, (loff_t)-1);
+ /* unmap again to remove racily COWed private pages */
+ unmap_mapping_range(inode->i_mapping, holebegin, 0, 1);
+ }
if (page)
page_cache_release(page);
- shmem_truncate_range(inode, newsize, (loff_t)-1);
}
setattr_copy(inode, attr);
struct shmem_xattr *xattr, *nxattr;
if (inode->i_mapping->a_ops == &shmem_aops) {
- truncate_inode_pages(inode->i_mapping, 0);
shmem_unacct_size(info->flags, inode->i_size);
inode->i_size = 0;
shmem_truncate_range(inode, 0, (loff_t)-1);
};
static const struct inode_operations shmem_inode_operations = {
- .setattr = shmem_notify_change,
+ .setattr = shmem_setattr,
.truncate_range = shmem_truncate_range,
#ifdef CONFIG_TMPFS_XATTR
.setxattr = shmem_setxattr,
.removexattr = shmem_removexattr,
#endif
#ifdef CONFIG_TMPFS_POSIX_ACL
- .setattr = shmem_notify_change,
+ .setattr = shmem_setattr,
.check_acl = generic_check_acl,
#endif
};
.removexattr = shmem_removexattr,
#endif
#ifdef CONFIG_TMPFS_POSIX_ACL
- .setattr = shmem_notify_change,
+ .setattr = shmem_setattr,
.check_acl = generic_check_acl,
#endif
};
return 0;
}
+void shmem_truncate_range(struct inode *inode, loff_t start, loff_t end)
+{
+ truncate_inode_pages_range(inode->i_mapping, start, end);
+}
+EXPORT_SYMBOL_GPL(shmem_truncate_range);
+
#ifdef CONFIG_CGROUP_MEM_RES_CTLR
/**
* mem_cgroup_get_shmem_target - find a page or entry assigned to the shmem file
vma->vm_flags |= VM_CAN_NONLINEAR;
return 0;
}
+
+/**
+ * shmem_read_mapping_page_gfp - read into page cache, using specified page allocation flags.
+ * @mapping: the page's address_space
+ * @index: the page index
+ * @gfp: the page allocator flags to use if allocating
+ *
+ * This behaves as a tmpfs "read_cache_page_gfp(mapping, index, gfp)",
+ * with any new page allocations done using the specified allocation flags.
+ * But read_cache_page_gfp() uses the ->readpage() method: which does not
+ * suit tmpfs, since it may have pages in swapcache, and needs to find those
+ * for itself; although drivers/gpu/drm i915 and ttm rely upon this support.
+ *
+ * Provide a stub for those callers to start using now, then later
+ * flesh it out to call shmem_getpage() with additional gfp mask, when
+ * shmem_file_splice_read() is added and shmem_readpage() is removed.
+ */
+struct page *shmem_read_mapping_page_gfp(struct address_space *mapping,
+ pgoff_t index, gfp_t gfp)
+{
+ return read_cache_page_gfp(mapping, index, gfp);
+}
+EXPORT_SYMBOL_GPL(shmem_read_mapping_page_gfp);
#include <linux/vmalloc.h>
#include <linux/pagemap.h>
#include <linux/namei.h>
-#include <linux/shm.h>
+#include <linux/shmem_fs.h>
#include <linux/blkdev.h>
#include <linux/random.h>
#include <linux/writeback.h>
* @lstart: offset from which to truncate
*
* Called under (and serialised by) inode->i_mutex.
+ *
+ * Note: When this function returns, there can be a page in the process of
+ * deletion (inside __delete_from_page_cache()) in the specified range. Thus
+ * mapping->nrpages can be non-zero when this function returns even after
+ * truncation of the whole mapping.
*/
void truncate_inode_pages(struct address_space *mapping, loff_t lstart)
{
return 0;
}
EXPORT_SYMBOL(vmtruncate);
+
+int vmtruncate_range(struct inode *inode, loff_t offset, loff_t end)
+{
+ struct address_space *mapping = inode->i_mapping;
+
+ /*
+ * If the underlying filesystem is not going to provide
+ * a way to truncate a range of blocks (punch a hole) -
+ * we should return failure right now.
+ */
+ if (!inode->i_op->truncate_range)
+ return -ENOSYS;
+
+ mutex_lock(&inode->i_mutex);
+ down_write(&inode->i_alloc_sem);
+ unmap_mapping_range(mapping, offset, (end - offset), 1);
+ inode->i_op->truncate_range(inode, offset, end);
+ /* unmap again to remove racily COWed private pages */
+ unmap_mapping_range(mapping, offset, (end - offset), 1);
+ up_write(&inode->i_alloc_sem);
+ mutex_unlock(&inode->i_mutex);
+
+ return 0;
+}
* If a zone is deemed to be full of pinned pages then just give it a light
* scan then give up on it.
*/
-static unsigned long shrink_zones(int priority, struct zonelist *zonelist,
+static void shrink_zones(int priority, struct zonelist *zonelist,
struct scan_control *sc)
{
struct zoneref *z;
struct zone *zone;
unsigned long nr_soft_reclaimed;
unsigned long nr_soft_scanned;
- unsigned long total_scanned = 0;
for_each_zone_zonelist_nodemask(zone, z, zonelist,
gfp_zone(sc->gfp_mask), sc->nodemask) {
continue;
if (zone->all_unreclaimable && priority != DEF_PRIORITY)
continue; /* Let kswapd poll it */
+ /*
+ * This steals pages from memory cgroups over softlimit
+ * and returns the number of reclaimed pages and
+ * scanned pages. This works for global memory pressure
+ * and balancing, not for a memcg's limit.
+ */
+ nr_soft_scanned = 0;
+ nr_soft_reclaimed = mem_cgroup_soft_limit_reclaim(zone,
+ sc->order, sc->gfp_mask,
+ &nr_soft_scanned);
+ sc->nr_reclaimed += nr_soft_reclaimed;
+ sc->nr_scanned += nr_soft_scanned;
+ /* need some check for avoid more shrink_zone() */
}
- nr_soft_scanned = 0;
- nr_soft_reclaimed = mem_cgroup_soft_limit_reclaim(zone,
- sc->order, sc->gfp_mask,
- &nr_soft_scanned);
- sc->nr_reclaimed += nr_soft_reclaimed;
- total_scanned += nr_soft_scanned;
-
shrink_zone(priority, zone, sc);
}
-
- return total_scanned;
}
static bool zone_reclaimable(struct zone *zone)
sc->nr_scanned = 0;
if (!priority)
disable_swap_token(sc->mem_cgroup);
- total_scanned += shrink_zones(priority, zonelist, sc);
+ shrink_zones(priority, zonelist, sc);
/*
* Don't shrink slabs when reclaiming memory from
* over limit cgroups
goto encrypt;
auth:
- if (test_and_set_bit(HCI_CONN_ENCRYPT_PEND, &conn->pend))
+ if (test_bit(HCI_CONN_ENCRYPT_PEND, &conn->pend))
return 0;
- hci_conn_auth(conn, sec_level, auth_type);
- return 0;
+ if (!hci_conn_auth(conn, sec_level, auth_type))
+ return 0;
encrypt:
if (conn->link_mode & HCI_LM_ENCRYPT)
}
} else if (sk->sk_state == BT_CONNECT2) {
struct l2cap_conn_rsp rsp;
- __u16 result;
+ __u16 res, stat;
if (!status) {
- sk->sk_state = BT_CONFIG;
- result = L2CAP_CR_SUCCESS;
+ if (bt_sk(sk)->defer_setup) {
+ struct sock *parent = bt_sk(sk)->parent;
+ res = L2CAP_CR_PEND;
+ stat = L2CAP_CS_AUTHOR_PEND;
+ parent->sk_data_ready(parent, 0);
+ } else {
+ sk->sk_state = BT_CONFIG;
+ res = L2CAP_CR_SUCCESS;
+ stat = L2CAP_CS_NO_INFO;
+ }
} else {
sk->sk_state = BT_DISCONN;
l2cap_sock_set_timer(sk, HZ / 10);
- result = L2CAP_CR_SEC_BLOCK;
+ res = L2CAP_CR_SEC_BLOCK;
+ stat = L2CAP_CS_NO_INFO;
}
rsp.scid = cpu_to_le16(chan->dcid);
rsp.dcid = cpu_to_le16(chan->scid);
- rsp.result = cpu_to_le16(result);
- rsp.status = cpu_to_le16(L2CAP_CS_NO_INFO);
+ rsp.result = cpu_to_le16(res);
+ rsp.status = cpu_to_le16(stat);
l2cap_send_cmd(conn, chan->ident, L2CAP_CONN_RSP,
sizeof(rsp), &rsp);
}
if (unlikely(ip_fast_csum((u8 *)iph, iph->ihl)))
return -EINVAL;
- if (iph->protocol != IPPROTO_IGMP)
+ if (iph->protocol != IPPROTO_IGMP) {
+ if ((iph->daddr & IGMP_LOCAL_GROUP_MASK) != IGMP_LOCAL_GROUP)
+ BR_INPUT_SKB_CB(skb)->mrouters_only = 1;
return 0;
+ }
len = ntohs(iph->tot_len);
if (skb->len < len || len < ip_hdrlen(skb))
skb = skb_peek_tail(queue);
exthdrlen = !skb ? rt->dst.header_len : 0;
- length += exthdrlen;
- transhdrlen += exthdrlen;
mtu = cork->fragsize;
hh_len = LL_RESERVED_SPACE(rt->dst.dev);
else
alloclen = fraglen;
+ alloclen += exthdrlen;
+
/* The last fragment gets additional space at tail.
* Note, with MSG_MORE we overallocate on fragments,
* because we have no idea what fragment will be
* the last.
*/
- if (datalen == length + fraggap) {
+ if (datalen == length + fraggap)
alloclen += rt->dst.trailer_len;
- /* make sure mtu is not reached */
- if (datalen > mtu - fragheaderlen - rt->dst.trailer_len)
- datalen -= ALIGN(rt->dst.trailer_len, 8);
- }
+
if (transhdrlen) {
skb = sock_alloc_send_skb(sk,
alloclen + hh_len + 15,
/*
* Find where to start putting bytes.
*/
- data = skb_put(skb, fraglen);
+ data = skb_put(skb, fraglen + exthdrlen);
skb_set_network_header(skb, exthdrlen);
skb->transport_header = (skb->network_header +
fragheaderlen);
- data += fragheaderlen;
+ data += fragheaderlen + exthdrlen;
if (fraggap) {
skb->csum = skb_copy_and_csum_bits(
*/
*rtp = NULL;
cork->fragsize = inet->pmtudisc == IP_PMTUDISC_PROBE ?
- rt->dst.dev->mtu : dst_mtu(rt->dst.path);
+ rt->dst.dev->mtu : dst_mtu(&rt->dst);
cork->dst = &rt->dst;
cork->length = 0;
cork->tx_flags = ipc->tx_flags;
const struct iphdr *iph = ip_hdr(skb);
struct rtable *rt;
struct flowi4 fl4 = {};
- unsigned long orefdst;
+ __be32 saddr = iph->saddr;
+ __u8 flags = 0;
unsigned int hh_len;
- unsigned int type;
- type = inet_addr_type(net, iph->saddr);
- if (skb->sk && inet_sk(skb->sk)->transparent)
- type = RTN_LOCAL;
- if (addr_type == RTN_UNSPEC)
- addr_type = type;
+ if (!skb->sk && addr_type != RTN_LOCAL) {
+ if (addr_type == RTN_UNSPEC)
+ addr_type = inet_addr_type(net, saddr);
+ if (addr_type == RTN_LOCAL || addr_type == RTN_UNICAST)
+ flags |= FLOWI_FLAG_ANYSRC;
+ else
+ saddr = 0;
+ }
/* some non-standard hacks like ipt_REJECT.c:send_reset() can cause
* packets with foreign saddr to appear on the NF_INET_LOCAL_OUT hook.
*/
- if (addr_type == RTN_LOCAL) {
- fl4.daddr = iph->daddr;
- if (type == RTN_LOCAL)
- fl4.saddr = iph->saddr;
- fl4.flowi4_tos = RT_TOS(iph->tos);
- fl4.flowi4_oif = skb->sk ? skb->sk->sk_bound_dev_if : 0;
- fl4.flowi4_mark = skb->mark;
- fl4.flowi4_flags = skb->sk ? inet_sk_flowi_flags(skb->sk) : 0;
- rt = ip_route_output_key(net, &fl4);
- if (IS_ERR(rt))
- return -1;
-
- /* Drop old route. */
- skb_dst_drop(skb);
- skb_dst_set(skb, &rt->dst);
- } else {
- /* non-local src, find valid iif to satisfy
- * rp-filter when calling ip_route_input. */
- fl4.daddr = iph->saddr;
- rt = ip_route_output_key(net, &fl4);
- if (IS_ERR(rt))
- return -1;
+ fl4.daddr = iph->daddr;
+ fl4.saddr = saddr;
+ fl4.flowi4_tos = RT_TOS(iph->tos);
+ fl4.flowi4_oif = skb->sk ? skb->sk->sk_bound_dev_if : 0;
+ fl4.flowi4_mark = skb->mark;
+ fl4.flowi4_flags = skb->sk ? inet_sk_flowi_flags(skb->sk) : flags;
+ rt = ip_route_output_key(net, &fl4);
+ if (IS_ERR(rt))
+ return -1;
- orefdst = skb->_skb_refdst;
- if (ip_route_input(skb, iph->daddr, iph->saddr,
- RT_TOS(iph->tos), rt->dst.dev) != 0) {
- dst_release(&rt->dst);
- return -1;
- }
- dst_release(&rt->dst);
- refdst_drop(orefdst);
- }
+ /* Drop old route. */
+ skb_dst_drop(skb);
+ skb_dst_set(skb, &rt->dst);
if (skb_dst(skb)->error)
return -1;
struct iphdr *niph;
const struct tcphdr *oth;
struct tcphdr _otcph, *tcph;
- unsigned int addr_type;
/* IP header checks: fragment. */
if (ip_hdr(oldskb)->frag_off & htons(IP_OFFSET))
if (oth->rst)
return;
+ if (skb_rtable(oldskb)->rt_flags & (RTCF_BROADCAST | RTCF_MULTICAST))
+ return;
+
/* Check checksum */
if (nf_ip_checksum(oldskb, hook, ip_hdrlen(oldskb), IPPROTO_TCP))
return;
nskb->csum_start = (unsigned char *)tcph - nskb->head;
nskb->csum_offset = offsetof(struct tcphdr, check);
- addr_type = RTN_UNSPEC;
- if (hook != NF_INET_FORWARD
-#ifdef CONFIG_BRIDGE_NETFILTER
- || (nskb->nf_bridge && nskb->nf_bridge->mask & BRNF_BRIDGED)
-#endif
- )
- addr_type = RTN_LOCAL;
-
/* ip_route_me_harder expects skb->dst to be set */
skb_dst_set_noref(nskb, skb_dst(oldskb));
nskb->protocol = htons(ETH_P_IP);
- if (ip_route_me_harder(nskb, addr_type))
+ if (ip_route_me_harder(nskb, RTN_UNSPEC))
goto free_nskb;
niph->ttl = ip4_dst_hoplimit(skb_dst(nskb));
if (noblock)
return -EAGAIN;
+
+ /* starting over for a new packet */
+ msg->msg_flags &= ~MSG_TRUNC;
goto try_again;
}
}
unlock_sock_fast(sk, slow);
- if (flags & MSG_DONTWAIT)
+ if (noblock)
return -EAGAIN;
+
+ /* starting over for a new packet */
+ msg->msg_flags &= ~MSG_TRUNC;
goto try_again;
}
MODULE_LICENSE("GPL");
MODULE_DESCRIPTION("Driver for Atmel Audio Bitstream DAC (ABDAC)");
-MODULE_AUTHOR("Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>");
+MODULE_AUTHOR("Hans-Christian Egtvedt <egtvedt@samfundet.no>");
MODULE_LICENSE("GPL");
MODULE_DESCRIPTION("Driver for Atmel AC97 controller");
-MODULE_AUTHOR("Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>");
+MODULE_AUTHOR("Hans-Christian Egtvedt <egtvedt@samfundet.no>");
#include "hpioctl.h"
#include <linux/pci.h>
-#include <linux/version.h>
#include <linux/init.h>
#include <linux/jiffies.h>
#include <linux/slab.h>
&((struct cs5535audio_dma_desc *) dma->desc_buf.area)[i];
desc->addr = cpu_to_le32(addr);
desc->size = cpu_to_le32(period_bytes);
- desc->ctlreserved = cpu_to_le32(PRD_EOP);
+ desc->ctlreserved = cpu_to_le16(PRD_EOP);
desc_addr += sizeof(struct cs5535audio_dma_desc);
addr += period_bytes;
}
lastdesc = &((struct cs5535audio_dma_desc *) dma->desc_buf.area)[periods];
lastdesc->addr = cpu_to_le32((u32) dma->desc_buf.addr);
lastdesc->size = 0;
- lastdesc->ctlreserved = cpu_to_le32(PRD_JMP);
+ lastdesc->ctlreserved = cpu_to_le16(PRD_JMP);
jmpprd_addr = cpu_to_le32(lastdesc->addr +
(sizeof(struct cs5535audio_dma_desc)*periods));
snd_printd(KERN_INFO "HDMI: out of range MNL %d\n", mnl);
goto out_fail;
} else
- strlcpy(e->monitor_name, buf + ELD_FIXED_BYTES, mnl);
+ strlcpy(e->monitor_name, buf + ELD_FIXED_BYTES, mnl + 1);
for (i = 0; i < e->sad_count; i++) {
if (ELD_FIXED_BYTES + mnl + 3 * (i + 1) > size) {
};
static const struct snd_pci_quirk cxt5066_cfg_tbl[] = {
+ SND_PCI_QUIRK(0x1025, 0x054c, "Acer Aspire 3830TG", CXT5066_AUTO),
SND_PCI_QUIRK_MASK(0x1025, 0xff00, 0x0400, "Acer", CXT5066_IDEAPAD),
SND_PCI_QUIRK(0x1028, 0x02d8, "Dell Vostro", CXT5066_DELL_VOSTRO),
SND_PCI_QUIRK(0x1028, 0x02f5, "Dell Vostro 320", CXT5066_IDEAPAD),
.patch = patch_cxt5066 },
{ .id = 0x14f15069, .name = "CX20585",
.patch = patch_cxt5066 },
+ { .id = 0x14f1506c, .name = "CX20588",
+ .patch = patch_cxt5066 },
{ .id = 0x14f1506e, .name = "CX20590",
.patch = patch_cxt5066 },
{ .id = 0x14f15097, .name = "CX20631",
MODULE_ALIAS("snd-hda-codec-id:14f15067");
MODULE_ALIAS("snd-hda-codec-id:14f15068");
MODULE_ALIAS("snd-hda-codec-id:14f15069");
+MODULE_ALIAS("snd-hda-codec-id:14f1506c");
MODULE_ALIAS("snd-hda-codec-id:14f1506e");
MODULE_ALIAS("snd-hda-codec-id:14f15097");
MODULE_ALIAS("snd-hda-codec-id:14f15098");
SND_PCI_QUIRK(0x1025, 0xe309, "ULI", ALC880_3ST_DIG),
SND_PCI_QUIRK(0x1025, 0xe310, "ULI", ALC880_3ST),
SND_PCI_QUIRK(0x1039, 0x1234, NULL, ALC880_6ST_DIG),
- SND_PCI_QUIRK(0x103c, 0x2a09, "HP", ALC880_5ST),
SND_PCI_QUIRK(0x1043, 0x10b3, "ASUS W1V", ALC880_ASUS_W1V),
SND_PCI_QUIRK(0x1043, 0x10c2, "ASUS W6A", ALC880_ASUS_DIG),
SND_PCI_QUIRK(0x1043, 0x10c3, "ASUS Wxx", ALC880_ASUS_DIG),
*/
enum {
PINFIX_FSC_H270,
+ PINFIX_HP_Z200,
};
static const struct alc_fixup alc262_fixups[] = {
{ }
}
},
+ [PINFIX_HP_Z200] = {
+ .type = ALC_FIXUP_PINS,
+ .v.pins = (const struct alc_pincfg[]) {
+ { 0x16, 0x99130120 }, /* internal speaker */
+ { }
+ }
+ },
};
static const struct snd_pci_quirk alc262_fixup_tbl[] = {
+ SND_PCI_QUIRK(0x103c, 0x170b, "HP Z200", PINFIX_HP_Z200),
SND_PCI_QUIRK(0x1734, 0x1147, "FSC Celsius H270", PINFIX_FSC_H270),
{}
};
ALC262_HP_BPC),
SND_PCI_QUIRK_MASK(0x103c, 0xff00, 0x1500, "HP z series",
ALC262_HP_BPC),
+ SND_PCI_QUIRK(0x103c, 0x170b, "HP Z200",
+ ALC262_AUTO),
SND_PCI_QUIRK_MASK(0x103c, 0xff00, 0x1700, "HP xw series",
ALC262_HP_BPC),
SND_PCI_QUIRK(0x103c, 0x2800, "HP D7000", ALC262_HP_BPC_D7000_WL),
SND_PCI_QUIRK(0x1043, 0x1205, "ASUS W7J", ALC268_3ST),
SND_PCI_QUIRK(0x1170, 0x0040, "ZEPTO", ALC268_ZEPTO),
SND_PCI_QUIRK(0x14c0, 0x0025, "COMPAL IFL90/JFL-92", ALC268_TOSHIBA),
- SND_PCI_QUIRK(0x152d, 0x0763, "Diverse (CPR2000)", ALC268_ACER),
SND_PCI_QUIRK(0x152d, 0x0771, "Quanta IL1", ALC267_QUANTA_IL1),
{}
};
struct via_spec *spec = codec->spec;
hda_nid_t nid = kcontrol->private_value;
unsigned int pinsel = ucontrol->value.enumerated.item[0];
+ unsigned int parm0, parm1;
/* Get Independent Mode index of headphone pin widget */
spec->hp_independent_mode = spec->hp_independent_mode_index == pinsel
? 1 : 0;
- if (spec->codec_type == VT1718S)
+ if (spec->codec_type == VT1718S) {
snd_hda_codec_write(codec, nid, 0,
AC_VERB_SET_CONNECT_SEL, pinsel ? 2 : 0);
+ /* Set correct mute switch for MW3 */
+ parm0 = spec->hp_independent_mode ?
+ AMP_IN_UNMUTE(0) : AMP_IN_MUTE(0);
+ parm1 = spec->hp_independent_mode ?
+ AMP_IN_MUTE(1) : AMP_IN_UNMUTE(1);
+ snd_hda_codec_write(codec, 0x1b, 0,
+ AC_VERB_SET_AMP_GAIN_MUTE, parm0);
+ snd_hda_codec_write(codec, 0x1b, 0,
+ AC_VERB_SET_AMP_GAIN_MUTE, parm1);
+ }
else
snd_hda_codec_write(codec, nid, 0,
AC_VERB_SET_CONNECT_SEL, pinsel);
{0x21, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(2)},
{0x21, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(3)},
{0x21, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(5)},
-
- /* Setup default input of Front HP to MW9 */
- {0x28, AC_VERB_SET_CONNECT_SEL, 0x1},
/* PW9 PW10 Output enable */
{0x2d, AC_VERB_SET_PIN_WIDGET_CONTROL, AC_PINCTL_OUT_EN},
{0x2e, AC_VERB_SET_PIN_WIDGET_CONTROL, AC_PINCTL_OUT_EN},
/* Enable Boost Volume backdoor */
{0x1, 0xf88, 0x8},
/* MW0/1/2/3/4: un-mute index 0 (AOWx), mute index 1 (MW9) */
- {0x18, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(0)},
+ {0x18, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(0)},
{0x19, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(0)},
{0x1a, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(0)},
- {0x1b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(0)},
+ {0x1b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(0)},
{0x1c, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(0)},
{0x18, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(1)},
{0x19, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(1)},
/* set MUX1 = 2 (AOW4), MUX2 = 1 (AOW3) */
{0x34, AC_VERB_SET_CONNECT_SEL, 0x2},
{0x35, AC_VERB_SET_CONNECT_SEL, 0x1},
- /* Unmute MW4's index 0 */
- {0x1c, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(0)},
{ }
};
if (err < 0)
return err;
} else if (i == AUTO_SEQ_FRONT) {
+ /* add control to mixer index 0 */
+ err = via_add_control(spec, VIA_CTL_WIDGET_VOL,
+ "Master Front Playback Volume",
+ HDA_COMPOSE_AMP_VAL(0x21, 3, 5,
+ HDA_INPUT));
+ if (err < 0)
+ return err;
+ err = via_add_control(spec, VIA_CTL_WIDGET_MUTE,
+ "Master Front Playback Switch",
+ HDA_COMPOSE_AMP_VAL(0x21, 3, 5,
+ HDA_INPUT));
+ if (err < 0)
+ return err;
/* Front */
sprintf(name, "%s Playback Volume", chname[i]);
err = via_add_control(
unsigned char max_channels_in;
unsigned char max_channels_out;
- char *channel_map_in;
- char *channel_map_out;
+ signed char *channel_map_in;
+ signed char *channel_map_out;
- char *channel_map_in_ss, *channel_map_in_ds, *channel_map_in_qs;
- char *channel_map_out_ss, *channel_map_out_ds, *channel_map_out_qs;
+ signed char *channel_map_in_ss, *channel_map_in_ds, *channel_map_in_qs;
+ signed char *channel_map_out_ss, *channel_map_out_ds, *channel_map_out_qs;
char **port_names_in;
char **port_names_out;
#include <linux/module.h>
#include <linux/moduleparam.h>
-#include <linux/version.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/delay.h>
if SND_IMX_SOC
-config SND_MXC_SOC_SSI
- tristate
-
config SND_MXC_SOC_FIQ
tristate
tristate "Audio on the the i.MX31ADS with WM1133-EV1 fitted"
depends on MACH_MX31ADS_WM1133_EV1 && EXPERIMENTAL
select SND_SOC_WM8350
- select SND_MXC_SOC_SSI
select SND_MXC_SOC_FIQ
help
Enable support for audio on the i.MX31ADS with the WM1133-EV1
tristate "SoC audio support for Visstrim M10 boards"
depends on MACH_IMX27_VISSTRIM_M10
select SND_SOC_TVL320AIC32X4
- select SND_MXC_SOC_SSI
select SND_MXC_SOC_MX2
help
Say Y if you want to add support for SoC audio on Visstrim SM10
tristate "SoC Audio support for Phytec phyCORE (and phyCARD) boards"
depends on MACH_PCM043 || MACH_PCA100
select SND_SOC_WM9712
- select SND_MXC_SOC_SSI
select SND_MXC_SOC_FIQ
help
Say Y if you want to add support for SoC audio on Phytec phyCORE
|| MACH_EUKREA_MBIMXSD35_BASEBOARD \
|| MACH_EUKREA_MBIMXSD51_BASEBOARD
select SND_SOC_TLV320AIC23
- select SND_MXC_SOC_SSI
select SND_MXC_SOC_FIQ
help
Enable I2S based access to the TLV320AIC23B codec attached
platform_driver_unregister(&imx_pcm_driver);
}
module_exit(snd_imx_pcm_exit);
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:imx-pcm-audio");
MODULE_AUTHOR("Sascha Hauer, <s.hauer@pengutronix.de>");
MODULE_DESCRIPTION("i.MX I2S/ac97 SoC Interface");
MODULE_LICENSE("GPL");
-
+MODULE_ALIAS("platform:imx-ssi");
if (!card->dev->coherent_dma_mask)
card->dev->coherent_dma_mask = DMA_BIT_MASK(32);
- if (dai->driver->playback.channels_min) {
+ if (pcm->streams[SNDRV_PCM_STREAM_PLAYBACK].substream) {
ret = pxa2xx_pcm_preallocate_dma_buffer(pcm,
SNDRV_PCM_STREAM_PLAYBACK);
if (ret)
goto out;
}
- if (dai->driver->capture.channels_min) {
+ if (pcm->streams[SNDRV_PCM_STREAM_CAPTURE].substream) {
ret = pxa2xx_pcm_preallocate_dma_buffer(pcm,
SNDRV_PCM_STREAM_CAPTURE);
if (ret)
codec->bulk_write_raw = snd_soc_hw_bulk_write_raw;
switch (control) {
- case SND_SOC_CUSTOM:
- break;
-
case SND_SOC_I2C:
#if defined(CONFIG_I2C) || (defined(CONFIG_I2C_MODULE) && defined(MODULE))
codec->hw_write = (hw_write_t)i2c_master_send;
}
module_exit(at73c213_exit);
-MODULE_AUTHOR("Hans-Christian Egtvedt <hcegtvedt@atmel.com>");
+MODULE_AUTHOR("Hans-Christian Egtvedt <egtvedt@samfundet.no>");
MODULE_DESCRIPTION("Sound driver for AT73C213 with Atmel SSC");
MODULE_LICENSE("GPL");
projects / platform / kernel / kernel-mfld-blackbay.git / commitdiff