config TARGET_NAS220
bool "BlackArmor NAS220"
-config TARGET_NSA310S
- bool "Zyxel NSA310S"
-
config TARGET_SBx81LIFKW
bool "Allied Telesis SBx81GS24/SBx81GT40/SBx81XS6/SBx81XS16"
source "board/Seagate/dockstar/Kconfig"
source "board/Seagate/goflexhome/Kconfig"
source "board/Seagate/nas220/Kconfig"
-source "board/zyxel/nsa310s/Kconfig"
source "board/alliedtelesis/SBx81LIFKW/Kconfig"
source "board/alliedtelesis/SBx81LIFXCAT/Kconfig"
+++ /dev/null
-# SPDX-License-Identifier: GPL-2.0+
-#
-# Copyright (C) 2015
-# Gerald Kerma <dreagle@doukki.net>
-# Tony Dinh <mibodhi@gmail.com>
-
-if TARGET_NSA310S
-
-config SYS_BOARD
- default "nsa310s"
-
-config SYS_VENDOR
- default "zyxel"
-
-config SYS_CONFIG_NAME
- default "nsa310s"
-
-endif
+++ /dev/null
-NSA310S BOARD
-M: Gerald Kerma <dreagle@doukki.net>
-M: Tony Dinh <mibodhi@gmail.com>
-M: Luka Perkov <luka.perkov@sartura.hr>
-S: Maintained
-F: board/zyxel/nsa310s/
-F: include/configs/nsa310s.h
-F: configs/nsa310s_defconfig
+++ /dev/null
-# SPDX-License-Identifier: GPL-2.0+
-#
-# Copyright (C) 2015
-# Gerald Kerma <dreagle@doukki.net>
-# Tony Dinh <mibodhi@gmail.com>
-
-obj-y := nsa310s.o
+++ /dev/null
-# SPDX-License-Identifier: GPL-2.0+
-#
-# Copyright (C) 2015
-# Gerald Kerma <dreagle@doukki.net>
-# Tony Dinh <mibodhi@gmail.com>
-# Refer to doc/README.kwbimage for more details about how-to
-# configure and create kirkwood boot images.
-#
-
-# Boot Media configurations
-BOOT_FROM nand
-NAND_ECC_MODE default
-NAND_PAGE_SIZE 0x0800
-
-# Configure RGMII-0 interface pad voltage to 1.8V
-DATA 0xFFD100e0 0x1b1b1b9b
-
-DATA 0xFFD01400 0x43010c30
-DATA 0xFFD01404 0x39543000
-DATA 0xFFD01408 0x22125451
-DATA 0xFFD0140C 0x00000833
-DATA 0xFFD01410 0x0000000C
-DATA 0xFFD01414 0x00000000
-DATA 0xFFD01418 0x00000000
-DATA 0xFFD0141C 0x00000652
-DATA 0xFFD01420 0x00000004
-DATA 0xFFD01424 0x0000F17F
-DATA 0xFFD01428 0x00085520
-DATA 0xFFD0147c 0x00008552
-DATA 0xFFD01504 0x0FFFFFF1
-DATA 0xFFD01508 0x10000000
-DATA 0xFFD0150C 0x00000000
-DATA 0xFFD01514 0x00000000
-DATA 0xFFD0151C 0x00000000
-DATA 0xFFD01494 0x00010000
-DATA 0xFFD01498 0x00000000
-DATA 0xFFD0149C 0x0000E403
-DATA 0xFFD01480 0x00000001
-DATA 0xFFD20134 0x66666666
-DATA 0xFFD20138 0x66666666
-DATA 0x0 0x0
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright (C) 2015
- * Gerald Kerma <dreagle@doukki.net>
- * Tony Dinh <mibodhi@gmail.com>
- */
-
-#include <common.h>
-#include <init.h>
-#include <miiphy.h>
-#include <net.h>
-#include <asm/arch/cpu.h>
-#include <asm/arch/soc.h>
-#include <asm/arch/mpp.h>
-#include <asm/global_data.h>
-#include <asm/io.h>
-#include "nsa310s.h"
-
-DECLARE_GLOBAL_DATA_PTR;
-
-int board_early_init_f(void)
-{
- /*
- * default gpio configuration
- * There are maximum 64 gpios controlled through 2 sets of registers
- * the below configuration configures mainly initial LED status
- */
- mvebu_config_gpio(NSA310S_VAL_LOW, NSA310S_VAL_HIGH,
- NSA310S_OE_LOW, NSA310S_OE_HIGH);
-
- /* (all LEDs & power off active high) */
- /* Multi-Purpose Pins Functionality configuration */
- static const u32 kwmpp_config[] = {
- MPP0_NF_IO2,
- MPP1_NF_IO3,
- MPP2_NF_IO4,
- MPP3_NF_IO5,
- MPP4_NF_IO6,
- MPP5_NF_IO7,
- MPP6_SYSRST_OUTn,
- MPP7_GPO,
- MPP8_TW_SDA,
- MPP9_TW_SCK,
- MPP10_UART0_TXD,
- MPP11_UART0_RXD,
- MPP12_GPO,
- MPP13_GPIO,
- MPP14_GPIO,
- MPP15_GPIO,
- MPP16_GPIO,
- MPP17_GPIO,
- MPP18_NF_IO0,
- MPP19_NF_IO1,
- MPP20_GPIO,
- MPP21_GPIO,
- MPP22_GPIO,
- MPP23_GPIO,
- MPP24_GPIO,
- MPP25_GPIO,
- MPP26_GPIO,
- MPP27_GPIO,
- MPP28_GPIO,
- MPP29_GPIO,
- MPP30_GPIO,
- MPP31_GPIO,
- MPP32_GPIO,
- MPP33_GPIO,
- MPP34_GPIO,
- MPP35_GPIO,
- 0
- };
- kirkwood_mpp_conf(kwmpp_config, NULL);
- return 0;
-}
-
-int board_init(void)
-{
- /* address of boot parameters */
- gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100;
-
- return 0;
-}
-
-#ifdef CONFIG_RESET_PHY_R
-void reset_phy(void)
-{
- u16 reg;
- u16 phyaddr;
- char *name = "egiga0";
-
- if (miiphy_set_current_dev(name))
- return;
-
- /* read PHY dev address */
- if (miiphy_read(name, 0xee, 0xee, (u16 *) &phyaddr)) {
- printf("could not read PHY dev address\n");
- return;
- }
-
- /* set RGMII delay */
- miiphy_write(name, phyaddr, MV88E1318_PGADR_REG, MV88E1318_MAC_CTRL_PG);
- miiphy_read(name, phyaddr, MV88E1318_MAC_CTRL_REG, ®);
- reg |= (MV88E1318_RGMII_RX_CTRL | MV88E1318_RGMII_TX_CTRL);
- miiphy_write(name, phyaddr, MV88E1318_MAC_CTRL_REG, reg);
- miiphy_write(name, phyaddr, MV88E1318_PGADR_REG, 0);
-
- /* reset PHY */
- if (miiphy_reset(name, phyaddr))
- return;
-
- /*
- * ZyXEL NSA310S uses the 88E1310S Alaska (interface identical to 88E1318)
- * and has an MCU attached to the LED[2] via tristate interrupt
- */
-
- /* switch to LED register page */
- miiphy_write(name, phyaddr, MV88E1318_PGADR_REG, MV88E1318_LED_PG);
- /* read out LED polarity register */
- miiphy_read(name, phyaddr, MV88E1318_LED_POL_REG, ®);
- /* clear 4, set 5 - LED2 low, tri-state */
- reg &= ~(MV88E1318_LED2_4);
- reg |= (MV88E1318_LED2_5);
- /* write back LED polarity register */
- miiphy_write(name, phyaddr, MV88E1318_LED_POL_REG, reg);
- /* jump back to page 0, per the PHY chip documenation. */
- miiphy_write(name, phyaddr, MV88E1318_PGADR_REG, 0);
-
- /* set PHY back to auto-negotiation mode */
- miiphy_write(name, phyaddr, 0x4, 0x1e1);
- miiphy_write(name, phyaddr, 0x9, 0x300);
- /* downshift */
- miiphy_write(name, phyaddr, 0x10, 0x3860);
- miiphy_write(name, phyaddr, 0x0, 0x9140);
-}
-#endif /* CONFIG_RESET_PHY_R */
+++ /dev/null
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * Copyright (C) 2015
- * Gerald Kerma <dreagle@doukki.net>
- * Tony Dinh <mibodhi@gmail.com>
- */
-
-#ifndef __NSA310S_H
-#define __NSA310S_H
-
-/* low GPIO's */
-#define HDD1_GREEN_LED (1 << 16)
-#define HDD1_RED_LED (1 << 13)
-#define USB_GREEN_LED (1 << 15)
-#define USB_POWER (1 << 21)
-#define SYS_GREEN_LED (1 << 28)
-#define SYS_ORANGE_LED (1 << 29)
-
-#define COPY_GREEN_LED (1 << 22)
-#define COPY_RED_LED (1 << 23)
-
-#define PIN_USB_GREEN_LED 15
-#define PIN_USB_POWER 21
-
-#define NSA310S_OE_LOW (~(0))
-#define NSA310S_VAL_LOW (SYS_GREEN_LED | USB_POWER)
-
-/* high GPIO's */
-#define HDD2_GREEN_LED (1 << 2)
-#define HDD2_POWER (1 << 1)
-
-#define NSA310S_OE_HIGH (~(0))
-#define NSA310S_VAL_HIGH (HDD2_POWER)
-
-/* PHY related */
-#define MV88E1318_PGADR_REG 22
-#define MV88E1318_MAC_CTRL_PG 2
-#define MV88E1318_MAC_CTRL_REG 21
-#define MV88E1318_RGMII_TX_CTRL (1 << 4)
-#define MV88E1318_RGMII_RX_CTRL (1 << 5)
-#define MV88E1318_LED_PG 3
-#define MV88E1318_LED_POL_REG 17
-#define MV88E1318_LED2_4 (1 << 4)
-#define MV88E1318_LED2_5 (1 << 5)
-
-#endif /* __NSA310S_H */
+++ /dev/null
-CONFIG_ARM=y
-CONFIG_SYS_DCACHE_OFF=y
-CONFIG_ARCH_CPU_INIT=y
-CONFIG_ARCH_KIRKWOOD=y
-CONFIG_SYS_TEXT_BASE=0x600000
-CONFIG_NR_DRAM_BANKS=2
-CONFIG_TARGET_NSA310S=y
-CONFIG_ENV_SIZE=0x20000
-CONFIG_ENV_OFFSET=0xE0000
-CONFIG_BOOTDELAY=3
-CONFIG_USE_PREBOOT=y
-# CONFIG_DISPLAY_BOARDINFO is not set
-CONFIG_HUSH_PARSER=y
-CONFIG_SYS_PROMPT="nsa310s => "
-CONFIG_CMD_BOOTZ=y
-# CONFIG_CMD_FLASH is not set
-CONFIG_CMD_IDE=y
-CONFIG_CMD_NAND=y
-CONFIG_CMD_USB=y
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
-CONFIG_CMD_EXT2=y
-CONFIG_CMD_FAT=y
-CONFIG_CMD_JFFS2=y
-CONFIG_CMD_MTDPARTS=y
-CONFIG_MTDPARTS_DEFAULT="mtdparts=orion_nand:0xe0000@0x0(uboot),0x20000@0xe0000(uboot_env),0x100000@0x100000(second_stage_uboot),-@0x200000(root)"
-CONFIG_CMD_UBI=y
-CONFIG_ISO_PARTITION=y
-CONFIG_ENV_OVERWRITE=y
-CONFIG_ENV_IS_IN_NAND=y
-CONFIG_SYS_RELOC_GD_ENV_ADDR=y
-CONFIG_NETCONSOLE=y
-# CONFIG_MMC is not set
-CONFIG_MTD=y
-CONFIG_MTD_RAW_NAND=y
-CONFIG_MVGBE=y
-CONFIG_MII=y
-CONFIG_SYS_NS16550=y
-CONFIG_USB=y
-CONFIG_USB_EHCI_HCD=y
-CONFIG_USB_STORAGE=y
-CONFIG_LZMA=y
-CONFIG_BZIP2=y
-CONFIG_OF_LIBFDT=y
+++ /dev/null
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * Copyright (C) 2015
- * Gerald Kerma <dreagle@doukki.net>
- * Tony Dinh <mibodhi@gmail.com>
- * Luka Perkov <luka.perkov@sartura.hr>
- */
-
-#ifndef _CONFIG_NSA310S_H
-#define _CONFIG_NSA310S_H
-
-/* high level configuration options */
-#define CONFIG_FEROCEON_88FR131 1 /* CPU Core subversion */
-#define CONFIG_KW88F6192 1 /* SOC Name */
-#define CONFIG_KW88F6702 1 /* SOC Name */
-#define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */
-
-#include "mv-common.h"
-
-/* environment variables configuration */
-
-/* default environment variables */
-#define CONFIG_BOOTCOMMAND \
- "setenv bootargs ${console} ${mtdparts} ${bootargs_root}; " \
- "ubi part root; " \
- "ubifsmount ubi:rootfs; " \
- "ubifsload 0x800000 ${kernel}; " \
- "ubifsload 0x700000 ${fdt}; " \
- "ubifsumount; " \
- "fdt addr 0x700000; fdt resize; fdt chosen; " \
- "bootz 0x800000 - 0x700000"
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "console=console=ttyS0,115200\0" \
- "mtdids=nand0=orion_nand\0" \
- "mtdparts="CONFIG_MTDPARTS_DEFAULT \
- "kernel=/boot/zImage\0" \
- "fdt=/boot/nsa310s.dtb\0" \
- "bootargs_root=ubi.mtd=3 root=ubi0:rootfs rootfstype=ubifs rw\0"
-
-/* Ethernet driver configuration */
-#ifdef CONFIG_CMD_NET
-#define CONFIG_MVGBE_PORTS {1, 0} /* enable port 0 only */
-#define CONFIG_PHY_BASE_ADR 1
-#define CONFIG_RESET_PHY_R
-#endif /* CONFIG_CMD_NET */
-
-/* SATA driver configuration */
-#ifdef CONFIG_IDE
-#define __io
-#define CONFIG_SYS_ATA_IDE0_OFFSET MV_SATA_PORT0_OFFSET
-#endif /* CONFIG_IDE */
-
-/* RTC driver configuration */
-#ifdef CONFIG_CMD_DATE
-#define CONFIG_RTC_MV
-#endif /* CONFIG_CMD_DATE */
-
-#endif /* _CONFIG_NSA310S_H */
projects / platform / kernel / u-boot.git / commitdiff