ARM: shmobile: Lager USB0 cable detection workaround

Add Lager board code to check the PWEN GPIO signal and refuse to
allow probe of the USBHS driver in case of DIP misconfiguration.

For correct operation Lager DIP switches SW5 and SW6 shall be
configured in 2-3 position to enable USB Function support.

If the DIP switch is configured incorrectly then the user can
simply adjust the hardware and either reboot or use the bind interface
to try to probe again:

# echo renesas_usbhs > /sys/bus/platform/drivers/renesas_usbhs/bind

Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
(cherry picked from commit 36be7686caa05334ca8d52df157b373a41d8d9f1)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

diff --git a/arch/arm/mach-shmobile/board-lager.c b/arch/arm/mach-shmobile/board-lager.c
index 30ebd08..6a7041f 100644 (file)
--- a/arch/arm/mach-shmobile/board-lager.c
+++ b/arch/arm/mach-shmobile/board-lager.c
@@ -408,13 +408,30 @@ static int usbhs_hardware_init(struct platform_device *pdev)
 {
        struct usbhs_private *priv = usbhs_get_priv(pdev);
        struct usb_phy *phy;
+       int ret;
+
+       /* USB0 Function - use PWEN as GPIO input to detect DIP Switch SW5
+        * setting to avoid VBUS short circuit due to wrong cable.
+        * PWEN should be pulled up high if USB Function is selected by SW5
+        */
+       gpio_request_one(RCAR_GP_PIN(5, 18), GPIOF_IN, NULL); /* USB0_PWEN */
+       if (!gpio_get_value(RCAR_GP_PIN(5, 18))) {
+               pr_warn("Error: USB Function not selected - check SW5 + SW6\n");
+               ret = -ENOTSUPP;
+               goto error;
+       }
 
        phy = usb_get_phy_dev(&pdev->dev, 0);
-       if (IS_ERR(phy))
-               return PTR_ERR(phy);
+       if (IS_ERR(phy)) {
+               ret = PTR_ERR(phy);
+               goto error;
+       }
 
        priv->phy = phy;
        return 0;
+ error:
+       gpio_free(RCAR_GP_PIN(5, 18));
+       return ret;
 }
 
 static int usbhs_hardware_exit(struct platform_device *pdev)
@@ -426,6 +443,8 @@ static int usbhs_hardware_exit(struct platform_device *pdev)
 
        usb_put_phy(priv->phy);
        priv->phy = NULL;
+
+       gpio_free(RCAR_GP_PIN(5, 18));
        return 0;
 }
 
@@ -536,7 +555,7 @@ static const struct pinctrl_map lager_pinctrl_map[] = {
                                  "vin1_clk", "vin1"),
        /* USB0 */
        PIN_MAP_MUX_GROUP_DEFAULT("renesas_usbhs", "pfc-r8a7790",
-                                 "usb0", "usb0"),
+                                 "usb0_ovc_vbus", "usb0"),
 };
 
 static void __init lager_add_standard_devices(void)