mtd: rawnand: denali: remove ->dev_ready() hook

The Denali NAND IP has no way to read out the current signal level
of the R/B# pin. Instead, denali_dev_ready() checks if the R/B#
transition has already happened. (The INTR__INT_ACT interrupt is
asserted at the rising edge of the R/B# pin.) It is not a correct
way to implement the ->dev_ready() hook.

In fact, it has a drawback; in the nand_scan_ident phase, the chip
detection iterates over maxchips until it fails to find a homogeneous
chip. For the last loop, nand_reset() fails if no chip is there.

If ->dev_ready hook exists, nand_command(_lp) calls nand_wait_ready()
after NAND_CMD_RESET. However, we know denali_dev_ready() never
returns 1 unless there exists a chip that toggles R/B# in that chip
select. Then, nand_wait_ready() just ends up with wasting 400 msec,
in the end, shows the "timeout while waiting for chip to become ready"
warning.

Let's remove the mis-implemented dev_ready hook, and fallback to
sending the NAND_CMD_STATUS and nand_wait_status_ready(), which
bails out more quickly.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>

diff --git a/drivers/mtd/nand/raw/denali.c b/drivers/mtd/nand/raw/denali.c
index bad3b8a..3f8ee92 100644 (file)
--- a/drivers/mtd/nand/raw/denali.c
+++ b/drivers/mtd/nand/raw/denali.c
@@ -204,18 +204,6 @@ static uint32_t denali_wait_for_irq(struct denali_nand_info *denali,
        return denali->irq_status;
 }
 
-static uint32_t denali_check_irq(struct denali_nand_info *denali)
-{
-       unsigned long flags;
-       uint32_t irq_status;
-
-       spin_lock_irqsave(&denali->irq_lock, flags);
-       irq_status = denali->irq_status;
-       spin_unlock_irqrestore(&denali->irq_lock, flags);
-
-       return irq_status;
-}
-
 static void denali_read_buf(struct nand_chip *chip, uint8_t *buf, int len)
 {
        struct mtd_info *mtd = nand_to_mtd(chip);
@@ -288,8 +276,7 @@ static void denali_cmd_ctrl(struct nand_chip *chip, int dat, unsigned int ctrl)
                return;
 
        /*
-        * Some commands are followed by chip->legacy.dev_ready or
-        * chip->legacy.waitfunc.
+        * Some commands are followed by chip->legacy.waitfunc.
         * irq_status must be cleared here to catch the R/B# interrupt later.
         */
        if (ctrl & NAND_CTRL_CHANGE)
@@ -298,13 +285,6 @@ static void denali_cmd_ctrl(struct nand_chip *chip, int dat, unsigned int ctrl)
        denali->host_write(denali, DENALI_BANK(denali) | type, dat);
 }
 
-static int denali_dev_ready(struct nand_chip *chip)
-{
-       struct denali_nand_info *denali = mtd_to_denali(nand_to_mtd(chip));
-
-       return !!(denali_check_irq(denali) & INTR__INT_ACT);
-}
-
 static int denali_check_erased_page(struct mtd_info *mtd,
                                    struct nand_chip *chip, uint8_t *buf,
                                    unsigned long uncor_ecc_flags,
@@ -1360,7 +1340,6 @@ int denali_init(struct denali_nand_info *denali)
        chip->legacy.read_byte = denali_read_byte;
        chip->legacy.write_byte = denali_write_byte;
        chip->legacy.cmd_ctrl = denali_cmd_ctrl;
-       chip->legacy.dev_ready = denali_dev_ready;
        chip->legacy.waitfunc = denali_waitfunc;
 
        if (features & FEATURES__INDEX_ADDR) {