docs: misc-devices/apds990x.txt: convert to ReST format

- Adjust title markup;
- Adjust identation.

Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Link: https://lore.kernel.org/r/444743782e5c8b8085d8016c8be3baabe4d23b53.1592203650.git.mchehab+huawei@kernel.org
Signed-off-by: Jonathan Corbet <corbet@lwn.net>

diff --git a/Documentation/misc-devices/apds990x.txt b/Documentation/misc-devices/apds990x.rst
similarity index 86%
rename from Documentation/misc-devices/apds990x.txt
rename to Documentation/misc-devices/apds990x.rst
index 454d95d..e2f7557 100644 (file)
--- a/Documentation/misc-devices/apds990x.txt
+++ b/Documentation/misc-devices/apds990x.rst
@@ -1,3 +1,6 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+======================
 Kernel driver apds990x
 ======================
 
@@ -50,14 +53,18 @@ chip_id
 
 power_state
        RW - enable / disable chip. Uses counting logic
+
             1 enables the chip
             0 disables the chip
 lux0_input
        RO - measured lux value
+
             sysfs_notify called when threshold interrupt occurs
 
 lux0_sensor_range
-       RO - lux0_input max value. Actually never reaches since sensor tends
+       RO - lux0_input max value.
+
+            Actually never reaches since sensor tends
             to saturate much before that. Real max value varies depending
             on the light spectrum etc.
 
@@ -68,7 +75,9 @@ lux0_rate_avail
        RO - supported measurement rates
 
 lux0_calibscale
-       RW - calibration value. Set to neutral value by default.
+       RW - calibration value.
+
+            Set to neutral value by default.
             Output results are multiplied with calibscale / calibscale_default
             value.
 
@@ -76,16 +85,21 @@ lux0_calibscale_default
        RO - neutral calibration value
 
 lux0_thresh_above_value
-       RW - HI level threshold value. All results above the value
+       RW - HI level threshold value.
+
+            All results above the value
             trigs an interrupt. 65535 (i.e. sensor_range) disables the above
             interrupt.
 
 lux0_thresh_below_value
-       RW - LO level threshold value. All results below the value
+       RW - LO level threshold value.
+
+            All results below the value
             trigs an interrupt. 0 disables the below interrupt.
 
 prox0_raw
        RO - measured proximity value
+
             sysfs_notify called when threshold interrupt occurs
 
 prox0_sensor_range
@@ -93,11 +107,14 @@ prox0_sensor_range
 
 prox0_raw_en
        RW - enable / disable proximity - uses counting logic
-            1 enables the proximity
-            0 disables the proximity
+
+            - 1 enables the proximity
+            - 0 disables the proximity
 
 prox0_reporting_mode
-       RW - trigger / periodic. In "trigger" mode the driver tells two possible
+       RW - trigger / periodic.
+
+            In "trigger" mode the driver tells two possible
             values: 0 or prox0_sensor_range value. 0 means no proximity,
             1023 means proximity. This causes minimal number of interrupts.
             In "periodic" mode the driver reports all values above

diff --git a/Documentation/misc-devices/index.rst b/Documentation/misc-devices/index.rst
index edf66b5..46072ce 100644 (file)
--- a/Documentation/misc-devices/index.rst
+++ b/Documentation/misc-devices/index.rst
@@ -15,6 +15,7 @@ fit into other categories.
    :maxdepth: 2
 
    ad525x_dpot
+   apds990x
    bh1770glc
    eeprom
    c2port