#define PEAK_PCI_CDR (CDR_CBP | CDR_CLKOUT_MASK)
#define PEAK_PCI_OCR OCR_TX0_PUSHPULL
-/*
- * Important PITA registers
- */
+/* Important PITA registers */
#define PITA_ICR 0x00 /* Interrupt control register */
#define PITA_GPIOICR 0x18 /* GPIO interface control register */
#define PITA_MISC 0x1C /* Miscellaneous register */
MODULE_DEVICE_TABLE(pci, peak_pci_tbl);
#ifdef CONFIG_CAN_PEAK_PCIEC
-/*
- * PCAN-ExpressCard needs I2C bit-banging configuration option.
- */
+/* PCAN-ExpressCard needs I2C bit-banging configuration option. */
/* GPIOICR byte access offsets */
#define PITA_GPOUT 0x18 /* GPx output value */
return (readb(card->cfg_base + PITA_GPIN) & PITA_GPIN_SCL) ? 1 : 0;
}
-/*
- * write commands to the LED chip though the I2C-bus of the PCAN-PCIeC
- */
+/* write commands to the LED chip though the I2C-bus of the PCAN-PCIeC */
static int peak_pciec_write_pca9553(struct peak_pciec_card *card,
u8 offset, u8 data)
{
return 0;
}
-/*
- * delayed work callback used to control the LEDs
- */
+/* delayed work callback used to control the LEDs */
static void peak_pciec_led_work(struct work_struct *work)
{
struct peak_pciec_card *card =
schedule_delayed_work(&card->led_work, HZ);
}
-/*
- * set LEDs blinking state
- */
+/* set LEDs blinking state */
static void peak_pciec_set_leds(struct peak_pciec_card *card, u8 led_mask, u8 s)
{
u8 new_led = card->led_cache;
peak_pciec_write_pca9553(card, 5, new_led);
}
-/*
- * start one second delayed work to control LEDs
- */
+/* start one second delayed work to control LEDs */
static void peak_pciec_start_led_work(struct peak_pciec_card *card)
{
schedule_delayed_work(&card->led_work, HZ);
}
-/*
- * stop LEDs delayed work
- */
+/* stop LEDs delayed work */
static void peak_pciec_stop_led_work(struct peak_pciec_card *card)
{
cancel_delayed_work_sync(&card->led_work);
}
-/*
- * initialize the PCA9553 4-bit I2C-bus LED chip
- */
+/* initialize the PCA9553 4-bit I2C-bus LED chip */
static int peak_pciec_init_leds(struct peak_pciec_card *card)
{
int err;
return peak_pciec_write_pca9553(card, 5, PCA9553_LS0_INIT);
}
-/*
- * restore LEDs state to off peak_pciec_leds_exit
- */
+/* restore LEDs state to off peak_pciec_leds_exit */
static void peak_pciec_leds_exit(struct peak_pciec_card *card)
{
/* switch LEDs to off */
peak_pciec_write_pca9553(card, 5, PCA9553_LED_OFF_ALL);
}
-/*
- * normal write sja1000 register method overloaded to catch when controller
+/* normal write sja1000 register method overloaded to catch when controller
* is started or stopped, to control leds
*/
static void peak_pciec_write_reg(const struct sja1000_priv *priv,
#else /* CONFIG_CAN_PEAK_PCIEC */
-/*
- * Placebo functions when PCAN-ExpressCard support is not selected
- */
+/* Placebo functions when PCAN-ExpressCard support is not selected */
static inline int peak_pciec_probe(struct pci_dev *pdev, struct net_device *dev)
{
return -ENODEV;
chan->prev_dev = pci_get_drvdata(pdev);
pci_set_drvdata(pdev, dev);
- /*
- * PCAN-ExpressCard needs some additional i2c init.
+ /* PCAN-ExpressCard needs some additional i2c init.
* This must be done *before* register_sja1000dev() but
* *after* devices linkage
*/
/* pci_xxx_config_word() return positive PCIBIOS_xxx error codes while
* the probe() function must return a negative errno in case of failure
- * (err is unchanged if negative) */
+ * (err is unchanged if negative)
+ */
return pcibios_err_to_errno(err);
}