powerpc: mpc85xx: Use binman to embed dtb inside U-Boot

Below is the sequence to embed dtb inside U-Boot,
1. Remove bootpg and resetvec section if needed
2. Append dtb
3. Append bootpg and resetvec section back if removed in step 1

Above procedure is required only when CONFIG_MPC85xx and
CONFIG_OF_SEPARATE are defined.

Add new config CONFIG_MPC85XX_HAVE_RESET_VECTOR to indicate that
image has resetvec section. Step 1 and step 3 described above are
required only if this config is y.

Signed-off-by: Jagdish Gediya <jagdish.gediya@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <york.sun@nxp.com>

diff --git a/Makefile b/Makefile
index e38966e..fa1a8dc 100644 (file)
--- a/Makefile
+++ b/Makefile
@@ -861,6 +861,10 @@ ifneq ($(CONFIG_SYS_INIT_SP_BSS_OFFSET),)
 ALL-y += init_sp_bss_offset_check
 endif
 
+ifeq ($(CONFIG_MPC85xx)$(CONFIG_OF_SEPARATE),yy)
+ALL-y += u-boot-with-dtb.bin
+endif
+
 LDFLAGS_u-boot += $(LDFLAGS_FINAL)
 
 # Avoid 'Not enough room for program headers' error on binutils 2.28 onwards.
@@ -983,7 +987,8 @@ spl/u-boot-spl.srec: spl/u-boot-spl FORCE
        $(call if_changed,objcopy)
 
 OBJCOPYFLAGS_u-boot-nodtb.bin := -O binary \
-               $(if $(CONFIG_X86_16BIT_INIT),-R .start16 -R .resetvec)
+               $(if $(CONFIG_X86_16BIT_INIT),-R .start16 -R .resetvec) \
+               $(if $(CONFIG_MPC85XX_HAVE_RESET_VECTOR),-R .bootpg -R .resetvec)
 
 OBJCOPYFLAGS_u-boot-spl.hex = $(OBJCOPYFLAGS_u-boot.hex)
 
@@ -1207,6 +1212,18 @@ u-boot-with-spl.sfp: spl/u-boot-spl.sfp u-boot.img FORCE
        $(call if_changed,socboot)
 endif
 
+ifeq ($(CONFIG_MPC85xx)$(CONFIG_OF_SEPARATE),yy)
+u-boot-with-dtb.bin: u-boot.bin u-boot.dtb \
+       $(if $(CONFIG_MPC85XX_HAVE_RESET_VECTOR), u-boot-br.bin) FORCE
+       $(call if_changed,binman)
+
+ifeq ($(CONFIG_MPC85XX_HAVE_RESET_VECTOR),y)
+OBJCOPYFLAGS_u-boot-br.bin := -O binary -j .bootpg -j .resetvec
+u-boot-br.bin: u-boot FORCE
+       $(call if_changed,objcopy)
+endif
+endif
+
 # x86 uses a large ROM. We fill it with 0xff, put the 16-bit stuff (including
 # reset vector) at the top, Intel ME descriptor at the bottom, and U-Boot in
 # the middle. This is handled by binman based on an image description in the
@@ -1301,8 +1318,12 @@ spl/u-boot-spl.pbl: spl/u-boot-spl.bin FORCE
 ifeq ($(ARCH),arm)
 UBOOT_BINLOAD := u-boot.img
 else
+ifeq ($(CONFIG_MPC85xx)$(CONFIG_OF_SEPARATE),yy)
+UBOOT_BINLOAD := u-boot-with-dtb.bin
+else
 UBOOT_BINLOAD := u-boot.bin
 endif
+endif
 
 OBJCOPYFLAGS_u-boot-with-spl-pbl.bin = -I binary -O binary --pad-to=$(CONFIG_SPL_PAD_TO) \
                          --gap-fill=0xff

diff --git a/arch/powerpc/cpu/mpc85xx/Kconfig b/arch/powerpc/cpu/mpc85xx/Kconfig
index 19e8d02..7d139ff 100644 (file)
--- a/arch/powerpc/cpu/mpc85xx/Kconfig
+++ b/arch/powerpc/cpu/mpc85xx/Kconfig
@@ -1143,6 +1143,10 @@ config ARCH_T4240
        imply CMD_REGINFO
        imply FSL_SATA
 
+config MPC85XX_HAVE_RESET_VECTOR
+       bool "Indicate reset vector at CONFIG_RESET_VECTOR_ADDRESS - 0xffc"
+       depends on MPC85xx
+
 config BOOKE
        bool
        default y