As explained in commit
3bedbcc3aa18 ("arm: mvebu: a38x: serdes: Don't
overwrite read-only SAR PCIe registers") it is required to set Maximum Link
Width bits of PCIe Root Port Link Capabilities Register depending of number
of used serdes lanes. As this register is part of PCIe address space and
not serdes address space, move it into pci_mvebu.c driver.
Read number of PCIe lanes from DT property "num-lanes" which is used also
by other PCIe controller drivers in Linux kernel. If this property is
absent then it defaults to 1. This property needs to be set to 4 for every
mvebu board which use PEX_ROOT_COMPLEX_X4 or PEX_BUS_MODE_X4.
Enabling of PCIe port needs to be done afer all registers in PCIe address
space are properly configure. For this purpose use new mvebu-reset driver
(part of system-controller) and remove this code from serdes code.
Because some PCIe ports cannot be enabled individually, it is required to
first setup all PCIe ports and then enable them.
This change contains also all required "num-lanes" and "resets" DTS
properties, to make pci_mvebu.c driver work correctly.
Signed-off-by: Pali Rohár <pali@kernel.org>
marvell,pcie-port = <0>;
marvell,pcie-lane = <0>;
clocks = <&gateclk 5>;
+ resets = <&systemc 0 0>;
status = "disabled";
};
marvell,pcie-port = <0>;
marvell,pcie-lane = <1>;
clocks = <&gateclk 6>;
+ resets = <&systemc 0 1>;
status = "disabled";
};
marvell,pcie-port = <0>;
marvell,pcie-lane = <0>;
clocks = <&gateclk 8>;
+ resets = <&systemc 0 0>;
status = "disabled";
};
marvell,pcie-port = <1>;
marvell,pcie-lane = <0>;
clocks = <&gateclk 5>;
+ resets = <&systemc 0 1>;
status = "disabled";
};
marvell,pcie-port = <2>;
marvell,pcie-lane = <0>;
clocks = <&gateclk 6>;
+ resets = <&systemc 0 2>;
status = "disabled";
};
};
marvell,pcie-port = <0>;
marvell,pcie-lane = <0>;
clocks = <&gateclk 8>;
+ resets = <&systemc 0 0>;
status = "disabled";
};
marvell,pcie-port = <1>;
marvell,pcie-lane = <0>;
clocks = <&gateclk 5>;
+ resets = <&systemc 0 1>;
status = "disabled";
};
marvell,pcie-port = <2>;
marvell,pcie-lane = <0>;
clocks = <&gateclk 6>;
+ resets = <&systemc 0 2>;
status = "disabled";
};
marvell,pcie-port = <3>;
marvell,pcie-lane = <0>;
clocks = <&gateclk 7>;
+ resets = <&systemc 0 3>;
status = "disabled";
};
};
marvell,pcie-port = <0>;
marvell,pcie-lane = <0>;
clocks = <&gateclk 5>;
+ resets = <&systemc 0 0>;
status = "disabled";
};
};
marvell,pcie-port = <0>;
marvell,pcie-lane = <0>;
clocks = <&gateclk 5>;
+ resets = <&systemc 0 0>;
status = "disabled";
};
marvell,pcie-port = <0>;
marvell,pcie-lane = <1>;
clocks = <&gateclk 6>;
+ resets = <&systemc 0 0>;
status = "disabled";
};
marvell,pcie-port = <0>;
marvell,pcie-lane = <2>;
clocks = <&gateclk 7>;
+ resets = <&systemc 0 0>;
status = "disabled";
};
marvell,pcie-port = <0>;
marvell,pcie-lane = <3>;
clocks = <&gateclk 8>;
+ resets = <&systemc 0 0>;
status = "disabled";
};
marvell,pcie-port = <1>;
marvell,pcie-lane = <0>;
clocks = <&gateclk 9>;
+ resets = <&systemc 0 1>;
status = "disabled";
};
};
marvell,pcie-port = <0>;
marvell,pcie-lane = <0>;
clocks = <&gateclk 5>;
+ resets = <&systemc 0 0>;
status = "disabled";
};
marvell,pcie-port = <0>;
marvell,pcie-lane = <1>;
clocks = <&gateclk 6>;
+ resets = <&systemc 0 0>;
status = "disabled";
};
marvell,pcie-port = <0>;
marvell,pcie-lane = <2>;
clocks = <&gateclk 7>;
+ resets = <&systemc 0 0>;
status = "disabled";
};
marvell,pcie-port = <0>;
marvell,pcie-lane = <3>;
clocks = <&gateclk 8>;
+ resets = <&systemc 0 0>;
status = "disabled";
};
marvell,pcie-port = <1>;
marvell,pcie-lane = <0>;
clocks = <&gateclk 9>;
+ resets = <&systemc 0 1>;
status = "disabled";
};
marvell,pcie-port = <1>;
marvell,pcie-lane = <1>;
clocks = <&gateclk 10>;
+ resets = <&systemc 0 1>;
status = "disabled";
};
marvell,pcie-port = <1>;
marvell,pcie-lane = <2>;
clocks = <&gateclk 11>;
+ resets = <&systemc 0 1>;
status = "disabled";
};
marvell,pcie-port = <1>;
marvell,pcie-lane = <3>;
clocks = <&gateclk 12>;
+ resets = <&systemc 0 1>;
status = "disabled";
};
marvell,pcie-port = <2>;
marvell,pcie-lane = <0>;
clocks = <&gateclk 26>;
+ resets = <&systemc 0 2>;
status = "disabled";
};
};
marvell,pcie-port = <0>;
marvell,pcie-lane = <0>;
clocks = <&gateclk 5>;
+ resets = <&systemc 0 0>;
status = "disabled";
};
marvell,pcie-port = <0>;
marvell,pcie-lane = <1>;
clocks = <&gateclk 6>;
+ resets = <&systemc 0 0>;
status = "disabled";
};
marvell,pcie-port = <0>;
marvell,pcie-lane = <2>;
clocks = <&gateclk 7>;
+ resets = <&systemc 0 0>;
status = "disabled";
};
marvell,pcie-port = <0>;
marvell,pcie-lane = <3>;
clocks = <&gateclk 8>;
+ resets = <&systemc 0 0>;
status = "disabled";
};
marvell,pcie-port = <1>;
marvell,pcie-lane = <0>;
clocks = <&gateclk 9>;
+ resets = <&systemc 0 1>;
status = "disabled";
};
marvell,pcie-port = <1>;
marvell,pcie-lane = <1>;
clocks = <&gateclk 10>;
+ resets = <&systemc 0 1>;
status = "disabled";
};
marvell,pcie-port = <1>;
marvell,pcie-lane = <2>;
clocks = <&gateclk 11>;
+ resets = <&systemc 0 1>;
status = "disabled";
};
marvell,pcie-port = <1>;
marvell,pcie-lane = <3>;
clocks = <&gateclk 12>;
+ resets = <&systemc 0 1>;
status = "disabled";
};
marvell,pcie-port = <2>;
marvell,pcie-lane = <0>;
clocks = <&gateclk 26>;
+ resets = <&systemc 0 2>;
status = "disabled";
};
marvell,pcie-port = <3>;
marvell,pcie-lane = <0>;
clocks = <&gateclk 27>;
+ resets = <&systemc 0 3>;
status = "disabled";
};
};
pcie@1,0 {
/* Port 0, Lane 0 */
status = "okay";
+ num-lanes = <4>;
};
/*
pcie@9,0 {
/* Port 2, Lane 0 */
status = "okay";
+ num-lanes = <4>;
};
};
# SPDX-License-Identifier: GPL-2.0+
-obj-$(CONFIG_SPL_BUILD) = ctrl_pex.o
obj-$(CONFIG_SPL_BUILD) += high_speed_env_spec.o
obj-$(CONFIG_SPL_BUILD) += high_speed_env_spec-38x.o
obj-$(CONFIG_SPL_BUILD) += seq_exec.o
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0
-/*
- * Copyright (C) Marvell International Ltd. and its affiliates
- */
-
-#include <common.h>
-#include <spl.h>
-#include <asm/io.h>
-#include <asm/arch/cpu.h>
-#include <asm/arch/soc.h>
-#include <linux/bitops.h>
-#include <linux/delay.h>
-
-#include "ctrl_pex.h"
-#include "sys_env_lib.h"
-
-int hws_pex_config(const struct serdes_map *serdes_map, u8 count)
-{
- enum serdes_type serdes_type;
- u32 idx, tmp;
-
- DEBUG_INIT_FULL_S("\n### hws_pex_config ###\n");
-
- tmp = reg_read(SOC_CONTROL_REG1);
- tmp &= ~0x03;
-
- for (idx = 0; idx < count; idx++) {
- serdes_type = serdes_map[idx].serdes_type;
- if ((serdes_type != PEX0) &&
- ((serdes_map[idx].serdes_mode == PEX_ROOT_COMPLEX_X4) ||
- (serdes_map[idx].serdes_mode == PEX_END_POINT_X4))) {
- /* for PEX by4 - relevant for the first port only */
- continue;
- }
-
- switch (serdes_type) {
- case PEX0:
- tmp |= 0x1 << PCIE0_ENABLE_OFFS;
- break;
- case PEX1:
- tmp |= 0x1 << PCIE1_ENABLE_OFFS;
- break;
- case PEX2:
- tmp |= 0x1 << PCIE2_ENABLE_OFFS;
- break;
- case PEX3:
- tmp |= 0x1 << PCIE3_ENABLE_OFFS;
- break;
- default:
- break;
- }
- }
-
- reg_write(SOC_CONTROL_REG1, tmp);
-
- return MV_OK;
-}
+++ /dev/null
-/* SPDX-License-Identifier: GPL-2.0 */
-/*
- * Copyright (C) Marvell International Ltd. and its affiliates
- */
-
-#ifndef _CTRL_PEX_H
-#define _CTRL_PEX_H
-
-#include <pci.h>
-#include "high_speed_env_spec.h"
-
-/* Direct access to PEX0 Root Port's PCIe Capability structure */
-#define PEX0_RP_PCIE_CFG_OFFSET (0x00080000 + 0x60)
-
-/* SOC_CONTROL_REG1 fields */
-#define PCIE0_ENABLE_OFFS 0
-#define PCIE0_ENABLE_MASK (0x1 << PCIE0_ENABLE_OFFS)
-#define PCIE1_ENABLE_OFFS 1
-#define PCIE1_ENABLE_MASK (0x1 << PCIE1_ENABLE_OFFS)
-#define PCIE2_ENABLE_OFFS 2
-#define PCIE2_ENABLE_MASK (0x1 << PCIE2_ENABLE_OFFS)
-#define PCIE3_ENABLE_OFFS 3
-#define PCIE4_ENABLE_MASK (0x1 << PCIE3_ENABLE_OFFS)
-
-int hws_pex_config(const struct serdes_map *serdes_map, u8 count);
-
-#endif
#include "high_speed_env_spec.h"
#include "sys_env_lib.h"
-#include "ctrl_pex.h"
/*
* serdes_seq_db - holds all serdes sequences, their size and the
After finish the Power_up sequence for all lanes,
the lanes should be released from reset state. */
CHECK_STATUS(hws_pex_tx_config_seq(serdes_map, count));
-
- /* PEX configuration */
- CHECK_STATUS(hws_pex_config(serdes_map, count));
}
/* USB2 configuration */
else
reg_data &= ~0x4000;
reg_write(SOC_CONTROL_REG1, reg_data);
-
- /*
- * Set Maximum Link Width to X1 or X4 in Root
- * Port's PCIe Link Capability register.
- * This register is read-only but if is not set
- * correctly then access to PCI config space of
- * endpoint card behind this Root Port does not
- * work.
- */
- reg_data = reg_read(PEX0_RP_PCIE_CFG_OFFSET +
- PCI_EXP_LNKCAP);
- reg_data &= ~PCI_EXP_LNKCAP_MLW;
- reg_data |= (is_pex_by1 ? 1 : 4) << 4;
- reg_write(PEX0_RP_PCIE_CFG_OFFSET +
- PCI_EXP_LNKCAP, reg_data);
}
CHECK_STATUS(mv_seq_exec(serdes_num, PEX_POWER_UP_SEQ));
bool "Enable Armada XP/38x PCIe driver"
depends on ARCH_MVEBU
select MISC
+ select DM_RESET
help
Say Y here if you want to enable PCIe controller support on
Armada XP/38x SoCs.
#include <dm/lists.h>
#include <dm/of_access.h>
#include <pci.h>
+#include <reset.h>
#include <asm/io.h>
#include <asm/arch/cpu.h>
#include <asm/arch/soc.h>
u32 intregs;
u32 port;
u32 lane;
+ bool is_x4;
int devfn;
u32 lane_mask;
int first_busno;
/* Only enable PCIe link, do not setup it */
static int mvebu_pcie_enable_link(struct mvebu_pcie *pcie, ofnode node)
{
- /* PCIe link is currently automatically enabled in SerDes code */
+ struct reset_ctl rst;
+ int ret;
+
+ ret = reset_get_by_index_nodev(node, 0, &rst);
+ if (ret == -ENOENT) {
+ return 0;
+ } else if (ret < 0) {
+ printf("%s: cannot get reset controller: %d\n", pcie->name, ret);
+ return ret;
+ }
+
+ ret = reset_request(&rst);
+ if (ret) {
+ printf("%s: cannot request reset controller: %d\n", pcie->name, ret);
+ return ret;
+ }
+
+ ret = reset_deassert(&rst);
+ reset_free(&rst);
+ if (ret) {
+ printf("%s: cannot enable PCIe port: %d\n", pcie->name, ret);
+ return ret;
+ }
+
return 0;
}
reg = readl(pcie->base + PCIE_CTRL_OFF);
reg |= PCIE_CTRL_RC_MODE;
writel(reg, pcie->base + PCIE_CTRL_OFF);
+
+ /*
+ * Set Maximum Link Width to X1 or X4 in Root Port's PCIe Link
+ * Capability register. This register is defined by PCIe specification
+ * as read-only but this mvebu controller has it as read-write and must
+ * be set to number of SerDes PCIe lanes (1 or 4). If this register is
+ * not set correctly then link with endpoint card is not established.
+ */
+ reg = readl(pcie->base + PCIE_CAPAB_OFF + PCI_EXP_LNKCAP);
+ reg &= ~PCI_EXP_LNKCAP_MLW;
+ reg |= (pcie->is_x4 ? 4 : 1) << 4;
+ writel(reg, pcie->base + PCIE_CAPAB_OFF + PCI_EXP_LNKCAP);
}
static int mvebu_pcie_probe(struct udevice *dev)
{
struct fdt_pci_addr pci_addr;
const u32 *addr;
+ u32 num_lanes;
int ret = 0;
int len;
sprintf(pcie->name, "pcie%d.%d", pcie->port, pcie->lane);
+ if (!ofnode_read_u32(node, "num-lanes", &num_lanes) && num_lanes == 4)
+ pcie->is_x4 = true;
+
/* devfn is in bits [15:8], see PCI_DEV usage */
ret = ofnode_read_pci_addr(node, FDT_PCI_SPACE_CONFIG, "reg", &pci_addr);
if (ret < 0) {
projects / platform / kernel / u-boot.git / commitdiff