--- /dev/null
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * dts file for Xilinx ZynqMP ZCU106
+ *
+ * (C) Copyright 2016, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ */
+
+/dts-v1/;
+
+#include "zynqmp.dtsi"
+#include "zynqmp-clk.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+ model = "ZynqMP ZCU106 RevA";
+ compatible = "xlnx,zynqmp-zcu106-revA", "xlnx,zynqmp-zcu106", "xlnx,zynqmp";
+
+ aliases {
+ ethernet0 = &gem3;
+ i2c0 = &i2c0;
+ i2c1 = &i2c1;
+ mmc0 = &sdhci1;
+ rtc0 = &rtc;
+ serial0 = &uart0;
+ serial1 = &uart1;
+ serial2 = &dcc;
+ };
+
+ chosen {
+ bootargs = "earlycon";
+ stdout-path = "serial0:115200n8";
+ };
+
+ memory@0 {
+ device_type = "memory";
+ reg = <0x0 0x0 0x0 0x80000000>, <0x8 0x00000000 0x0 0x80000000>;
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ autorepeat;
+ sw19 {
+ label = "sw19";
+ gpios = <&gpio 22 GPIO_ACTIVE_HIGH>;
+ linux,code = <KEY_DOWN>;
+ gpio-key,wakeup;
+ autorepeat;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ heartbeat_led {
+ label = "heartbeat";
+ gpios = <&gpio 23 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
+};
+
+&can1 {
+ status = "okay";
+};
+
+&dcc {
+ status = "okay";
+};
+
+/* fpd_dma clk 667MHz, lpd_dma 500MHz */
+&fpd_dma_chan1 {
+ status = "okay";
+};
+
+&fpd_dma_chan2 {
+ status = "okay";
+};
+
+&fpd_dma_chan3 {
+ status = "okay";
+};
+
+&fpd_dma_chan4 {
+ status = "okay";
+};
+
+&fpd_dma_chan5 {
+ status = "okay";
+};
+
+&fpd_dma_chan6 {
+ status = "okay";
+};
+
+&fpd_dma_chan7 {
+ status = "okay";
+};
+
+&fpd_dma_chan8 {
+ status = "okay";
+};
+
+&gem3 {
+ status = "okay";
+ phy-handle = <&phy0>;
+ phy-mode = "rgmii-id";
+ phy0: phy@c {
+ reg = <0xc>;
+ ti,rx-internal-delay = <0x8>;
+ ti,tx-internal-delay = <0xa>;
+ ti,fifo-depth = <0x1>;
+ };
+};
+
+&gpio {
+ status = "okay";
+};
+
+&i2c0 {
+ status = "okay";
+ clock-frequency = <400000>;
+
+ tca6416_u97: gpio@20 {
+ compatible = "ti,tca6416";
+ reg = <0x20>;
+ gpio-controller; /* interrupt not connected */
+ #gpio-cells = <2>;
+ /*
+ * IRQ not connected
+ * Lines:
+ * 0 - SFP_SI5328_INT_ALM
+ * 1 - HDMI_SI5328_INT_ALM
+ * 5 - IIC_MUX_RESET_B
+ * 6 - GEM3_EXP_RESET_B
+ * 10 - FMC_HPC0_PRSNT_M2C_B
+ * 11 - FMC_HPC1_PRSNT_M2C_B
+ * 2-4, 7, 12-17 - not connected
+ */
+ };
+
+ tca6416_u61: gpio@21 {
+ compatible = "ti,tca6416";
+ reg = <0x21>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ /*
+ * IRQ not connected
+ * Lines:
+ * 0 - VCCPSPLL_EN
+ * 1 - MGTRAVCC_EN
+ * 2 - MGTRAVTT_EN
+ * 3 - VCCPSDDRPLL_EN
+ * 4 - MIO26_PMU_INPUT_LS
+ * 5 - PL_PMBUS_ALERT
+ * 6 - PS_PMBUS_ALERT
+ * 7 - MAXIM_PMBUS_ALERT
+ * 10 - PL_DDR4_VTERM_EN
+ * 11 - PL_DDR4_VPP_2V5_EN
+ * 12 - PS_DIMM_VDDQ_TO_PSVCCO_ON
+ * 13 - PS_DIMM_SUSPEND_EN
+ * 14 - PS_DDR4_VTERM_EN
+ * 15 - PS_DDR4_VPP_2V5_EN
+ * 16 - 17 - not connected
+ */
+ };
+
+ i2c-mux@75 { /* u60 */
+ compatible = "nxp,pca9544";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x75>;
+ i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ /* PS_PMBUS */
+ ina226@40 { /* u76 */
+ compatible = "ti,ina226";
+ reg = <0x40>;
+ shunt-resistor = <5000>;
+ };
+ ina226@41 { /* u77 */
+ compatible = "ti,ina226";
+ reg = <0x41>;
+ shunt-resistor = <5000>;
+ };
+ ina226@42 { /* u78 */
+ compatible = "ti,ina226";
+ reg = <0x42>;
+ shunt-resistor = <5000>;
+ };
+ ina226@43 { /* u87 */
+ compatible = "ti,ina226";
+ reg = <0x43>;
+ shunt-resistor = <5000>;
+ };
+ ina226@44 { /* u85 */
+ compatible = "ti,ina226";
+ reg = <0x44>;
+ shunt-resistor = <5000>;
+ };
+ ina226@45 { /* u86 */
+ compatible = "ti,ina226";
+ reg = <0x45>;
+ shunt-resistor = <5000>;
+ };
+ ina226@46 { /* u93 */
+ compatible = "ti,ina226";
+ reg = <0x46>;
+ shunt-resistor = <5000>;
+ };
+ ina226@47 { /* u88 */
+ compatible = "ti,ina226";
+ reg = <0x47>;
+ shunt-resistor = <5000>;
+ };
+ ina226@4a { /* u15 */
+ compatible = "ti,ina226";
+ reg = <0x4a>;
+ shunt-resistor = <5000>;
+ };
+ ina226@4b { /* u92 */
+ compatible = "ti,ina226";
+ reg = <0x4b>;
+ shunt-resistor = <5000>;
+ };
+ };
+ i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ /* PL_PMBUS */
+ ina226@40 { /* u79 */
+ compatible = "ti,ina226";
+ reg = <0x40>;
+ shunt-resistor = <2000>;
+ };
+ ina226@41 { /* u81 */
+ compatible = "ti,ina226";
+ reg = <0x41>;
+ shunt-resistor = <5000>;
+ };
+ ina226@42 { /* u80 */
+ compatible = "ti,ina226";
+ reg = <0x42>;
+ shunt-resistor = <5000>;
+ };
+ ina226@43 { /* u84 */
+ compatible = "ti,ina226";
+ reg = <0x43>;
+ shunt-resistor = <5000>;
+ };
+ ina226@44 { /* u16 */
+ compatible = "ti,ina226";
+ reg = <0x44>;
+ shunt-resistor = <5000>;
+ };
+ ina226@45 { /* u65 */
+ compatible = "ti,ina226";
+ reg = <0x45>;
+ shunt-resistor = <5000>;
+ };
+ ina226@46 { /* u74 */
+ compatible = "ti,ina226";
+ reg = <0x46>;
+ shunt-resistor = <5000>;
+ };
+ ina226@47 { /* u75 */
+ compatible = "ti,ina226";
+ reg = <0x47>;
+ shunt-resistor = <5000>;
+ };
+ };
+ i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+ /* MAXIM_PMBUS - 00 */
+ max15301@a { /* u46 */
+ compatible = "maxim,max15301";
+ reg = <0xa>;
+ };
+ max15303@b { /* u4 */
+ compatible = "maxim,max15303";
+ reg = <0xb>;
+ };
+ max15303@10 { /* u13 */
+ compatible = "maxim,max15303";
+ reg = <0x10>;
+ };
+ max15301@13 { /* u47 */
+ compatible = "maxim,max15301";
+ reg = <0x13>;
+ };
+ max15303@14 { /* u7 */
+ compatible = "maxim,max15303";
+ reg = <0x14>;
+ };
+ max15303@15 { /* u6 */
+ compatible = "maxim,max15303";
+ reg = <0x15>;
+ };
+ max15303@16 { /* u10 */
+ compatible = "maxim,max15303";
+ reg = <0x16>;
+ };
+ max15303@17 { /* u9 */
+ compatible = "maxim,max15303";
+ reg = <0x17>;
+ };
+ max15301@18 { /* u63 */
+ compatible = "maxim,max15301";
+ reg = <0x18>;
+ };
+ max15303@1a { /* u49 */
+ compatible = "maxim,max15303";
+ reg = <0x1a>;
+ };
+ max15303@1b { /* u8 */
+ compatible = "maxim,max15303";
+ reg = <0x1b>;
+ };
+ max15303@1d { /* u18 */
+ compatible = "maxim,max15303";
+ reg = <0x1d>;
+ };
+
+ max20751@72 { /* u95 */
+ compatible = "maxim,max20751";
+ reg = <0x72>;
+ };
+ max20751@73 { /* u96 */
+ compatible = "maxim,max20751";
+ reg = <0x73>;
+ };
+ };
+ /* Bus 3 is not connected */
+ };
+};
+
+&i2c1 {
+ status = "okay";
+ clock-frequency = <400000>;
+
+ /* PL i2c via PCA9306 - u45 */
+ i2c-mux@74 { /* u34 */
+ compatible = "nxp,pca9548";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x74>;
+ i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ /*
+ * IIC_EEPROM 1kB memory which uses 256B blocks
+ * where every block has different address.
+ * 0 - 256B address 0x54
+ * 256B - 512B address 0x55
+ * 512B - 768B address 0x56
+ * 768B - 1024B address 0x57
+ */
+ eeprom: eeprom@54 { /* u23 */
+ compatible = "atmel,24c08";
+ reg = <0x54>;
+ };
+ };
+ i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ si5341: clock-generator@36 { /* SI5341 - u69 */
+ reg = <0x36>;
+ };
+
+ };
+ i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+ si570_1: clock-generator@5d { /* USER SI570 - u42 */
+ #clock-cells = <0>;
+ compatible = "silabs,si570";
+ reg = <0x5d>;
+ temperature-stability = <50>;
+ factory-fout = <300000000>;
+ clock-frequency = <300000000>;
+ };
+ };
+ i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+ si570_2: clock-generator@5d { /* USER MGT SI570 - u56 */
+ #clock-cells = <0>;
+ compatible = "silabs,si570";
+ reg = <0x5d>;
+ temperature-stability = <50>; /* copy from zc702 */
+ factory-fout = <156250000>;
+ clock-frequency = <148500000>;
+ };
+ };
+ i2c@4 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <4>;
+ si5328: clock-generator@69 {/* SI5328 - u20 */
+ reg = <0x69>;
+ };
+ };
+ i2c@5 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <5>; /* FAN controller */
+ temp@4c {/* lm96163 - u128 */
+ compatible = "national,lm96163";
+ reg = <0x4c>;
+ };
+ };
+ /* 6 - 7 unconnected */
+ };
+
+ i2c-mux@75 {
+ compatible = "nxp,pca9548"; /* u135 */
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x75>;
+
+ i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ /* HPC0_IIC */
+ };
+ i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ /* HPC1_IIC */
+ };
+ i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+ /* SYSMON */
+ };
+ i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+ /* DDR4 SODIMM */
+ };
+ i2c@4 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <4>;
+ /* SEP 3 */
+ };
+ i2c@5 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <5>;
+ /* SEP 2 */
+ };
+ i2c@6 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <6>;
+ /* SEP 1 */
+ };
+ i2c@7 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <7>;
+ /* SEP 0 */
+ };
+ };
+};
+
+&rtc {
+ status = "okay";
+};
+
+&sata {
+ status = "okay";
+ /* SATA OOB timing settings */
+ ceva,p0-cominit-params = /bits/ 8 <0x18 0x40 0x18 0x28>;
+ ceva,p0-comwake-params = /bits/ 8 <0x06 0x14 0x08 0x0E>;
+ ceva,p0-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>;
+ ceva,p0-retry-params = /bits/ 16 <0x96A4 0x3FFC>;
+ ceva,p1-cominit-params = /bits/ 8 <0x18 0x40 0x18 0x28>;
+ ceva,p1-comwake-params = /bits/ 8 <0x06 0x14 0x08 0x0E>;
+ ceva,p1-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>;
+ ceva,p1-retry-params = /bits/ 16 <0x96A4 0x3FFC>;
+};
+
+/* SD1 with level shifter */
+&sdhci1 {
+ status = "okay";
+ no-1-8-v;
+};
+
+&uart0 {
+ status = "okay";
+};
+
+&uart1 {
+ status = "okay";
+};
+
+/* ULPI SMSC USB3320 */
+&usb0 {
+ status = "okay";
+};
+
+&watchdog0 {
+ status = "okay";
+};
projects / platform / kernel / linux-rpi3.git / commitdiff