staging: hp100: Properly indent the multiline comments.

Shift the end of multiline comments "*/" to the next line and align the
lines of the comments properly to improve code readability and to adhere
to the Linux Kernel coding style.
Reported by checkpatch.pl

Signed-off-by: Soumyajit Deb <debsoumyajit100@gmail.com>
Link: https://lore.kernel.org/r/20200325180003.46749-1-debsoumyajit100@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

diff --git a/drivers/staging/hp/hp100.c b/drivers/staging/hp/hp100.c
index 5f04ad2..62359f5 100644 (file)
--- a/drivers/staging/hp/hp100.c
+++ b/drivers/staging/hp/hp100.c
@@ -687,13 +687,15 @@ static int hp100_probe1(struct net_device *dev, int ioaddr, u_char bus,
 
        /* TODO: We do not need this with old cards, where PDLs are stored
         * in the cards shared memory area. But currently, busmaster has been
-        * implemented/tested only with the lassen chip anyway... */
+        * implemented/tested only with the lassen chip anyway...
+        */
        if (lp->mode == 1) {    /* busmaster */
                dma_addr_t page_baddr;
                /* Get physically continuous memory for TX & RX PDLs    */
                /* Conversion to new PCI API :
                 * Pages are always aligned and zeroed, no need to it ourself.
-                * Doc says should be OK for EISA bus as well - Jean II */
+                * Doc says should be OK for EISA bus as well - Jean II
+                */
                lp->page_vaddr_algn = pci_alloc_consistent(lp->pci_dev, MAX_RINGSIZE, &page_baddr);
                if (!lp->page_vaddr_algn) {
                        err = -ENOMEM;
@@ -851,7 +853,8 @@ static void hp100_hwinit(struct net_device *dev)
 
        /* Until here it was code from HWdiscover procedure. */
        /* Next comes code from mmuinit procedure of SCO BM driver which is
-        * called from HWconfigure in the SCO driver.  */
+        * called from HWconfigure in the SCO driver.
+        */
 
        /* Initialise MMU, eventually switch on Busmaster Mode, initialise
         * multicast filter...
@@ -1241,7 +1244,8 @@ static int hp100_build_rx_pdl(hp100_ring_t * ringptr,
 
        /* Allocate skb buffer of maximum size */
        /* Note: This depends on the alloc_skb functions allocating more
-        * space than requested, i.e. aligning to 16bytes */
+        * space than requested, i.e. aligning to 16bytes
+        */
 
        ringptr->skb = netdev_alloc_skb(dev, roundup(MAX_ETHER_SIZE + 2, 4));
 
@@ -1270,7 +1274,8 @@ static int hp100_build_rx_pdl(hp100_ring_t * ringptr,
 #endif
 
                /* Conversion to new PCI API : map skbuf data to PCI bus.
-                * Doc says it's OK for EISA as well - Jean II */
+                * Doc says it's OK for EISA as well - Jean II
+                */
                ringptr->pdl[0] = 0x00020000;   /* Write PDH */
                ringptr->pdl[3] = pdl_map_data(netdev_priv(dev),
                                               ringptr->skb->data);
@@ -1322,7 +1327,7 @@ static void hp100_rxfill(struct net_device *dev)
 
        while (lp->rxrcommit < MAX_RX_PDL) {
                /*
-                  ** Attempt to get a buffer and build a Rx PDL.
+                * Attempt to get a buffer and build a Rx PDL.
                 */
                ringptr = lp->rxrtail;
                if (0 == hp100_build_rx_pdl(ringptr, dev)) {
@@ -1541,7 +1546,8 @@ static netdev_tx_t hp100_start_xmit_bm(struct sk_buff *skb,
                ringptr->pdl[2] = skb->len;     /* 1st Frag: Length of frag */
        }
        /* Conversion to new PCI API : map skbuf data to PCI bus.
-        * Doc says it's OK for EISA as well - Jean II */
+        * Doc says it's OK for EISA as well - Jean II
+        */
        ringptr->pdl[1] = ((u32) pci_map_single(lp->pci_dev, skb->data, ringptr->pdl[2], PCI_DMA_TODEVICE));    /* 1st Frag: Adr. of data */
 
        /* Hand this PDL to the card. */
@@ -1680,7 +1686,8 @@ static netdev_tx_t hp100_start_xmit(struct sk_buff *skb,
        hp100_ints_off();
        val = hp100_inw(IRQ_STATUS);
        /* Ack / clear the interrupt TX_COMPLETE interrupt - this interrupt is set
-        * when the current packet being transmitted on the wire is completed. */
+        * when the current packet being transmitted on the wire is completed.
+        */
        hp100_outw(HP100_TX_COMPLETE, IRQ_STATUS);
 #ifdef HP100_DEBUG_TX
        printk("hp100: %s: start_xmit: irq_status=0x%.4x, irqmask=0x%.4x, len=%d\n",
@@ -1855,7 +1862,8 @@ static void hp100_rx_bm(struct net_device *dev)
                return;
        } else
                /* RX_PKT_CNT states how many PDLs are currently formatted and available to
-                * the cards BM engine */
+                * the cards BM engine
+                */
        if ((hp100_inw(RX_PKT_CNT) & 0x00ff) >= lp->rxrcommit) {
                printk("hp100: %s: More packets received than committed? RX_PKT_CNT=0x%x, commit=0x%x\n",
                                     dev->name, hp100_inw(RX_PKT_CNT) & 0x00ff,
@@ -2340,7 +2348,8 @@ static void hp100_start_interface(struct net_device *dev)
        }
 
        /* Note : before hp100_set_multicast_list(), because it will play with
-        * spinlock itself... Jean II */
+        * spinlock itself... Jean II
+        */
        spin_unlock_irqrestore(&lp->lock, flags);
 
        /* Enable MAC Tx and RX, set MAC modes, ... */